Showing 1–11 of 11 results for author: team, t J

3D MHD modelling of plasmoid drift following massive material injection in a tokamak

Authors: M. Kong, E. Nardon, D. Bonfiglio, M. Hoelzl, D. Hu, the JOREK team, the EUROfusion Tokamak Exploitation Team

Abstract: Mechanisms of plasmoid drift in the presence of massive material injection are studied via 3D non-linear MHD modelling with the JOREK code, using a transient neutral source deposited on the low field side midplane of a JET H-mode plasma to clarify basic processes and compare with existing theory. The simulations confirm the important role of the propagation of shear Alfvén waves (SAWs) from both e… ▽ More Mechanisms of plasmoid drift in the presence of massive material injection are studied via 3D non-linear MHD modelling with the JOREK code, using a transient neutral source deposited on the low field side midplane of a JET H-mode plasma to clarify basic processes and compare with existing theory. The simulations confirm the important role of the propagation of shear Alfvén waves (SAWs) from both ends of the plasmoid ("SAW braking") and the development of external resistive currents along magnetic field lines ("Pégourié braking") in limiting charge separation and thus the $\mathbf{E}\times \mathbf{B}$ plasmoid drift, where $\mathbf{E}$ and $\mathbf{B}$ are the electric and magnetic fields, respectively. The drift velocity is found to be limited by the SAW braking for cases with relatively small source amplitude while the Pégourié braking is shown to be stronger with larger toroidal extent of the source, both in good agreement with existing theory. The simulations also identity the key role of the size of the $\mathbf{E}\times \mathbf{B}$ flow region on plasmoid drift and show that the saturated velocity caused by dominant SAW braking agrees well with theory when considering an effective pressure within the $\mathbf{E}\times \mathbf{B}$ flow region. The existence of SAWs in the simulations is demonstrated and the 3D picture of plasmoid drift is also discussed. △ Less

Submitted 1 July, 2024; originally announced July 2024.

Comments: To be submitted to Nuclear Fusion

Neural-Parareal: Dynamically Training Neural Operators as Coarse Solvers for Time-Parallelisation of Fusion MHD Simulations

Authors: S. J. P. Pamela, N. Carey, J. Brandstetter, R. Akers, L. Zanisi, J. Buchanan, V. Gopakumar, M. Hoelzl, G. Huijsmans, K. Pentland, T. James, G. Antonucci, the JOREK Team

Abstract: The fusion research facility ITER is currently being assembled to demonstrate that fusion can be used for industrial energy production, while several other programmes across the world are also moving forward, such as EU-DEMO, CFETR, SPARC and STEP. The high engineering complexity of a tokamak makes it an extremely challenging device to optimise, and test-based optimisation would be too slow and to… ▽ More The fusion research facility ITER is currently being assembled to demonstrate that fusion can be used for industrial energy production, while several other programmes across the world are also moving forward, such as EU-DEMO, CFETR, SPARC and STEP. The high engineering complexity of a tokamak makes it an extremely challenging device to optimise, and test-based optimisation would be too slow and too costly. Instead, digital design and optimisation must be favored, which requires strongly-coupled suites of High-Performance Computing calculations. In this context, having surrogate models to provide quick estimates with uncertainty quantification is essential to explore and optimise new design options. Furthermore, these surrogates can in turn be used to accelerate simulations in the first place. This is the case of Parareal, a time-parallelisation method that can speed-up large HPC simulations, where the coarse-solver can be replaced by a surrogate. A novel framework, Neural-Parareal, is developed to integrate the training of neural operators dynamically as more data becomes available. For a given input-parameter domain, as more simulations are being run with Parareal, the large amount of data generated by the algorithm is used to train new surrogate models to be used as coarse-solvers for future Parareal simulations, leading to progressively more accurate coarse-solvers, and thus higher speed-up. It is found that such neural network surrogates can be much more effective than traditional coarse-solver in providing a speed-up with Parareal. This study is a demonstration of the convergence of HPC and AI which simply has to become common practice in the world of digital engineering design. △ Less

Submitted 2 May, 2024; originally announced May 2024.

Implementation of matrix compression in the coupling of JOREK to realistic 3D conducting wall structures

Authors: Federico Cipolletta, Nina Schwarz, Matthias Hoelzl, Salvatore Ventre, Nicola Isernia, Guglielmo Rubinacci, Alejandro Soba, Mervi Johanna Mantsinen, the JOREK Team

Abstract: JOREK is an advanced non-linear simulation code for studying MHD instabilities in magnetically confined fusion plasmas and their control and/or mitigation. A free-boundary and resistive wall extension was introduced via coupling to the STARWALL and CARIDDI codes, both able to provide dense response matrices describing the electromagnetic interactions between plasma and conducting structures. For d… ▽ More JOREK is an advanced non-linear simulation code for studying MHD instabilities in magnetically confined fusion plasmas and their control and/or mitigation. A free-boundary and resistive wall extension was introduced via coupling to the STARWALL and CARIDDI codes, both able to provide dense response matrices describing the electromagnetic interactions between plasma and conducting structures. For detailed CAD representations of the conducting structures and high resolutions for the plasma region, memory and computing time limitations restrict the possibility of simulating the ITER tokamak. In the present work, the Singular Value Decomposition provided by routines from the ScaLAPACK library has been successfully applied to compress some of the dense response matrices and thus optimize memory usage. This is demonstrated for simulations of Tearing Mode and Vertical Displacement Event instabilities. An outlook to future applications on large production cases and further extensions of the method are discussed. △ Less

Submitted 25 April, 2024; originally announced April 2024.

Comments: 19 pages, 9 figures, firstly presented at the 4th Fusion HPC Workshop in November 2023, submitted to Plasma Physics and Controlled Fusion in April 2024

Nonlinear MHD modeling of soft $β$ limits in W7-AS

Authors: Rohan Ramasamy, Ksenia Aleynikova, Nikita Nikulsin, Florian Hindenlang, Ihor Holod, Erika Strumberger, Matthias Hoelzl, the JOREK team

Abstract: An important question for the outlook of stellarator reactors is their robustness against pressure driven modes, and the underlying mechanism behind experimentally observed soft $β$ limits. Towards building a robust answer to these questions, simulation studies are presented using a recently derived reduced nonlinear MHD model. First, the initial model implementation is extended to capture fluid c… ▽ More An important question for the outlook of stellarator reactors is their robustness against pressure driven modes, and the underlying mechanism behind experimentally observed soft $β$ limits. Towards building a robust answer to these questions, simulation studies are presented using a recently derived reduced nonlinear MHD model. First, the initial model implementation is extended to capture fluid compression by including the influence of parallel flows. Linear benchmarks of a (2, 1) tearing mode in W7-AS geometry, and interchange modes in a finite $β$, net-zero current carrying stellarator with low magnetic shear are then used to demonstrate the modeling capabilities. Finally, a validation study is conducted on experimental reconstructions of finite $β$ W7-AS discharges. In agreement with past experimental analysis, it is shown that (i) the MHD activity is resistive, (ii) a soft $β$ limit is observed, when the plasma resistivity approaches the estimated experimental value, and (iii) low $n$ MHD activity is observed at intermediate $β$ values, particularly a nonlinearly dominant (2, 1) mode. The MHD activity is mild, explaining the soft $β$ limit, because the plasma volume remains separated into distinct sub-volumes in which field lines are ergodically confined. For the assumed transport parameters, the enhanced perpendicular transport along stochastic magnetic field lines can be overcome with the experimental heating power. The limitations in the current modeling are described, alongside an outlook for characterising soft $β$ limits in more detail in future work. △ Less

Submitted 5 February, 2024; originally announced February 2024.

Comments: Submitted to Nuclear Fusion

Validation of the plasma-wall self-organization model for density limit in ECRH-assisted start-up of Ohmic discharges on J-TEXT

Authors: Jiaxing Liu, ** Zhu, Dominique Franck Escande, Junli Zhang, Donghui Xia, Yuhan Wang, Jiaming Wang, Qinghu Yang, Jiangang Fang, Li Gao, Zhifeng Cheng, Zhipeng Chen, Zhoujun Yang, Zhongyong Chen, Yonghua Ding, Yuan Pan, the J-TEXT team

Abstract: A recently developed plasma-wall self-organization (PWSO) model predicts a significantly enhanced density limit, which may be attainable in tokamaks with ECRH-assisted ohmic startup and sufficiently high initial neutral density. Experiments have been conducted on J-TEXT to validate such a density limit scenario based on this model. Experimental results demonstrate that increasing the pre-filled ga… ▽ More A recently developed plasma-wall self-organization (PWSO) model predicts a significantly enhanced density limit, which may be attainable in tokamaks with ECRH-assisted ohmic startup and sufficiently high initial neutral density. Experiments have been conducted on J-TEXT to validate such a density limit scenario based on this model. Experimental results demonstrate that increasing the pre-filled gas pressure or ECRH power during the startup phase can effectively enhance plasma purity and raise the density limit at the flat-top. Despite the dominant carbon fraction in the wall material, some discharges approach the edge of the density-free regime of the 1D model of PWSO. △ Less

Submitted 17 April, 2023; originally announced April 2023.

Comments: 17 pages, 8 figures

Probing non-linear MHD stability of the EDA H-mode in ASDEX Upgrade

Authors: A Cathey, M Hoelzl, L Gil, MG Dunne, GF Harrer, GTA Huijsmans, J Kalis, K Lackner, SJP Pamela, E Wolfrum, S Günter, the JOREK team, the ASDEX Upgrade Team, the EUROfusion MST1 Team

Abstract: Regimes of operation in tokamaks that are devoid of large ELMs have to be better understood to extrapolate their applicability to reactor-relevant devices. This paper describes non-linear extended MHD simulations that use an experimental equilibrium from an EDA H-mode in ASDEX Upgrade. Linear ideal MHD analysis indicates that the operational point lies slightly inside of the stable region. The non… ▽ More Regimes of operation in tokamaks that are devoid of large ELMs have to be better understood to extrapolate their applicability to reactor-relevant devices. This paper describes non-linear extended MHD simulations that use an experimental equilibrium from an EDA H-mode in ASDEX Upgrade. Linear ideal MHD analysis indicates that the operational point lies slightly inside of the stable region. The non-linear simulations with the visco-resistive extended MHD code, JOREK, sustain non-axisymmetric perturbations that are linearly most unstable with toroidal mode numbers of n = \{6 \dots 9\}, but non-linearly higher and lower n become driven and the low-n become dominant. The poloidal mode velocity during the linear phase is found to correspond to the expected velocity for resistive ballooning modes. The perturbations that exist in the simulations have somewhat smaller poloidal wavenumbers (k_θ \sim 0.1 to 0.5 cm^{-1} ) than the experimental expectations for the quasi-coherent mode in EDA, and cause non-negligible transport in both the heat and particle channels. In the transition from linear to non-linear phase, the mode frequency chirps down from approximately 35 kHz to 13 kHz, which corresponds approximately to the lower end of frequencies that are typically observed in EDA H-modes in ASDEX Upgrade. △ Less

Submitted 22 January, 2023; originally announced January 2023.

Modelling of saturated external MHD instabilities in tokamaks: a comparison of 3D free boundary equilibria and nonlinear stability calculations

Authors: Rohan Ramasamy, Guillermo Bustos Ramirez, Matthias Hoelzl, Jonathan Graves, Guillermo Suárez López, Karl Lackner, Sibylle Günter, the JOREK team

Abstract: 3D free boundary equilibrium computations have recently been used to model external kinks and edge harmonic oscillations (EHOs), comparing with linear MHD stability codes, and nonlinear analytic theory [Kleiner et al, PPCF 61 084005 (2019)]. In this study, results of the VMEC equilibrium code are compared further with nonlinear reduced MHD simulations, using the JOREK code. The purpose of this inv… ▽ More 3D free boundary equilibrium computations have recently been used to model external kinks and edge harmonic oscillations (EHOs), comparing with linear MHD stability codes, and nonlinear analytic theory [Kleiner et al, PPCF 61 084005 (2019)]. In this study, results of the VMEC equilibrium code are compared further with nonlinear reduced MHD simulations, using the JOREK code. The purpose of this investigation is to understand the extent to which the modelling approaches agree, and identify the important physical effects which can modify the dynamics. For the simulated external kink, which is dominated by a single toroidal harmonic, good agreement is found when a large Lundquist number is used in the JOREK simulation, such that resistive effects are sub-dominant. Modelling EHOs where multiple toroidal harmonics are linearly unstable, the saturated perturbation observed can differ in the dominant toroidal harmonic. On the ideal timescale, a n=2 EHO is observed in JOREK, while the saturated perturbation predicted by VMEC is a n=1 mode. Extending simulations into timescales where resistive effects can play a role, similar n=1 perturbations can be found. The coupling of different linearly unstable toroidal harmonics in the JOREK simulation broadens the magnetic energy spectrum and ergodises the plasma edge region, resulting in a more localised pressure perturbation. These effects are not observed in VMEC, because closed magnetic flux surfaces are enforced. Despite the sensitivity of JOREK results on the assumed resistivity, saturated states can be found using both approaches that are in reasonable agreement, even for this more advanced case. △ Less

Submitted 3 June, 2022; v1 submitted 9 March, 2022; originally announced March 2022.

Comments: Submitted to Physics of Plasmas, with revisions from review process included

Complete 3D MHD simulations of the current quench phase of ITER mitigated disruptions

Authors: F. J. Artola, A. Loarte, M. Hoelzl, M. Lehnen, N. Schwarz, the JOREK team

Abstract: Complete 3D simulations of the current quench phase of ITER disruptions are key to predict asymmetric forces acting into the ITER wall. We present for the first time such simulations for ITER mitigated disruptions at realistic Lundquist numbers. For these strongly mitigated disruptions, we find that the edge safety factor remains above 2 and the maximal integral horizontal forces remain below 1 MN… ▽ More Complete 3D simulations of the current quench phase of ITER disruptions are key to predict asymmetric forces acting into the ITER wall. We present for the first time such simulations for ITER mitigated disruptions at realistic Lundquist numbers. For these strongly mitigated disruptions, we find that the edge safety factor remains above 2 and the maximal integral horizontal forces remain below 1 MN. The maximal integral vertical force is found to be 13 MN and arises in a time scale given by the resistive wall time as expected from theoretical considerations. In this respect, the vertical force arises after the plasma current has completely decayed, showing the importance of continuing the simulations also in the absence of plasma current. We conclude that the horizontal wall force rotation is not a concern for these strongly mitigated disruptions in ITER, since when the wall forces form, there are no remaining sources of rotation. △ Less

Submitted 10 December, 2021; originally announced December 2021.

Comments: to be submitted to Nuclear Fusion

Journal ref: Nuclear Fusion 2021

MHD simulations of small ELMs at low triangularity in ASDEX Upgrade

Authors: A. Cathey, M. Hoelzl, G. Harrer, M. G. Dunne, G. T. A. Huijsmans, K. Lackner, S. J. P. Pamela, E. Wolfrum, S. Günter, the JOREK team, the ASDEX Upgrade Team, the EUROfusion MST1 Team

Abstract: The development of small- and no-ELM regimes for ITER is a high priority topic due to the risks associated to type-I ELMs. By considering non-linear extended MHD simulations of the ASDEX Upgrade tokamak with the JOREK code, we probe a regime that avoids type-I ELMs completely provided that the separatrix density is high enough. The dynamics of the pedestal in this regime are observed to be qualita… ▽ More The development of small- and no-ELM regimes for ITER is a high priority topic due to the risks associated to type-I ELMs. By considering non-linear extended MHD simulations of the ASDEX Upgrade tokamak with the JOREK code, we probe a regime that avoids type-I ELMs completely provided that the separatrix density is high enough. The dynamics of the pedestal in this regime are observed to be qualitatively similar to the so-called quasi-continuous exhaust (QCE) regime in several ways. Repetitive type-I ELMs are substituted by roughly constant levels of outwards transport caused by peeling-ballooning modes (with dominant ballooning characteristics) which are localised in the last 5\% of the confined region (in normalised poloidal flux). The simulated low triangularity plasma transitions to a type-I ELMy H-mode if the separatrix density is sufficiently reduced or if the input heating power is sufficiently increased. The stabilising factors that play a role in the suppression of the small ELMs are also investigated by analysing the simulations, and the importance of including diamagnetic effects in the simulations is highlighted. By considering a scan in the pedestal resistivity and by measuring the poloidal velocity of the modes (and comparing to theoretical estimates for ideal and resistive modes), we identify the underlying instabilities as resistive peeling-ballooning modes. Decreasing the resistivity below experimentally-relevant conditions (i.e., going towards ideal MHD), the peeling-ballooning modes that constrain the pedestal below the type-I ELM stability boundary display sharply decreasing growth rates. △ Less

Submitted 15 October, 2021; originally announced October 2021.

Comparing spontaneous and pellet-triggered ELMs via non-linear extended MHD simulations

Authors: A. Cathey, M. Hoelzl, S. Futatani, P. T. Lang, K. Lackner, G. T. A. Huijsmans, S. J. P. Pamela, S. Günter, the JOREK team, the ASDEX Upgrade Team, the EUROfusion MST1 Team

Abstract: Injecting frozen deuterium pellets into an ELMy H-mode plasma is a well established scheme for triggering edge localized modes (ELMs) before they naturally occur. Based on an ASDEX Upgrade H-mode plasma, this article presents a comparison of extended MHD simulations of spontaneous type-I ELMs and pellet-triggered ELMs allowing to study their non-linear dynamics in detail. In particular, pellet-tri… ▽ More Injecting frozen deuterium pellets into an ELMy H-mode plasma is a well established scheme for triggering edge localized modes (ELMs) before they naturally occur. Based on an ASDEX Upgrade H-mode plasma, this article presents a comparison of extended MHD simulations of spontaneous type-I ELMs and pellet-triggered ELMs allowing to study their non-linear dynamics in detail. In particular, pellet-triggered ELMs are simulated by injecting deuterium pellets into different time points during the pedestal build-up described in [A. Cathey et al. Nuclear Fusion 60, 124007 (2020)]. Realistic ExB and diamagnetic background plasma flows as well as the time dependent bootstrap current evolution are included during the build-up to capture the balance between stabilising and destabilising terms for the edge instabilities accurately. Dependencies on the pellet size and injection times are studied. The spatio-temporal structures of the modes and the resulting divertor heat fluxes are compared in detail between spontaneous and triggered ELMs. We observe that the premature excitation of ELMs by means of pellet injection is caused by a helical perturbation described by a toroidal mode number of n = 1. In accordance with experimental observations, the pellet-triggered ELMs show reduced thermal energy losses and narrower divertor wetted area with respect to spontaneous ELMs. The peak divertor energy fluency is seen to decrease when ELMs are triggered by pellets injected earlier during the pedestal build-up. △ Less

Submitted 11 February, 2021; originally announced February 2021.

Non-linear extended MHD simulations of type-I edge localised mode cycles in ASDEX Upgrade and their underlying triggering mechanism

Authors: Andres Cathey, M. Hoelzl, K. Lackner, G. T. A. Huijsmans, M. G. Dunne, E. Wolfrum, S. J. P. Pamela, F. Orain, S. Günter, the JOREK team, the ASDEX Upgrade Team, the EUROfusion MST1 Team

Abstract: A triggering mechanism responsible for the explosive onset of edge localised modes (ELMs) in fusion plasmas is identified by performing, for the first time, non-linear magnetohydrodynamic simulations of repetitive type-I ELMs. Briefly prior to the ELM crash, destabilising and stabilising terms are affected at different timescales by an increasingly ergodic magnetic field caused by non-linear inter… ▽ More A triggering mechanism responsible for the explosive onset of edge localised modes (ELMs) in fusion plasmas is identified by performing, for the first time, non-linear magnetohydrodynamic simulations of repetitive type-I ELMs. Briefly prior to the ELM crash, destabilising and stabilising terms are affected at different timescales by an increasingly ergodic magnetic field caused by non-linear interactions between the axisymmetric background plasma and growing non-axisymmetric perturbations. The separation of timescales prompts the explosive, i.e. faster than exponential, growth of an ELM crash which lasts ${\sim}$ 500 $μ$s. The duration and size of the simulated ELM crashes compare qualitatively well with type-I ELMs in ASDEX Upgrade. As expected for type-I ELMs, a direct proportionality between the heating power in the simulations and the ELM repetition frequency is obtained. The simulations presented here are a major step forward towards predictive modelling of ELMs and of the assessment of mitigation techniques in ITER and other future tokamaks. △ Less

Submitted 26 October, 2020; v1 submitted 20 July, 2020; originally announced July 2020.