Showing 1–42 of 42 results for author: Zaleski, S

The atomizing pulsed jet

Authors: Yash Kulkarni, Cesar Pairetti, Raphaël Villiers, Stéphane Popinet, Stéphane Zaleski

Abstract: Direct Numerical Simulations of the injection of a pulsed round liquid jet in a stagnant gas are performed. The Reynolds and Weber numbers and the density ratio are sufficiently large for reaching a complex high-speed atomization regime. The Weber number based on grid size is small, an indication that the simulations are very well resolved. Computations are performed using octree adaptive mesh ref… ▽ More Direct Numerical Simulations of the injection of a pulsed round liquid jet in a stagnant gas are performed. The Reynolds and Weber numbers and the density ratio are sufficiently large for reaching a complex high-speed atomization regime. The Weber number based on grid size is small, an indication that the simulations are very well resolved. Computations are performed using octree adaptive mesh refinement using the Basilisk free-code platform, down to a specified minimum grid size $Δ$. Qualitative analysis of the flow and its topology reveal a complex structure of ligaments, sheets, droplets and bubbles that evolve and interact through impacts, ligament breakup, sheet rupture and engulfment of air bubbles in the liquid. A rich gallery of images of entangled structures is produced. Most processes occurring in this type of atomization are reproduced in detail, except at the instant of thin sheet perforation or breakup. We analyze drop statistics, showing that as the grid resolution is increased, the small-scale part of the distribution does not converge, and contains a large number of droplets close in order of magnitude to the minimum grid size with a significant peak at $d = 3Δ$ . This non-convergence arises from the numerical sheet breakup effect, in which the interface becomes rough just before it breaks. The rough appearance of the interface is associated to a high-wavenumber oscillation of the curvature. To recover convergence, we apply the controlled "manifold death" numerical procedure, in which thin sheets are detected, and then pierced by fiat before they reach a set critical thickness $h_c$ that is always larger than $6 Δ$. This allows convergence of the droplet frequency above a certain critical diameter $d_c$ above and close to $h_c$. A unimodal distribution is observed in the converged range. △ Less

Submitted 14 May, 2024; v1 submitted 3 May, 2024; originally announced May 2024.

Direct numerical simulations of microlayer formation during heterogeneous bubble nucleation

Authors: Mandeep Saini, Xiang Bin Chen, Stephane Zaleski, Daniel Fuster

Abstract: In this article, we present direct numerical simulation results for the expansion of spherical cap bubbles attached to a rigid wall due to a sudden drop in the ambient pressure. The critical pressure drop beyond which the bubble growth becomes unstable is found to match well with the predictions from classical theory of heterogeneous nucleation imposing a quasi-static bubble evolution. When the pr… ▽ More In this article, we present direct numerical simulation results for the expansion of spherical cap bubbles attached to a rigid wall due to a sudden drop in the ambient pressure. The critical pressure drop beyond which the bubble growth becomes unstable is found to match well with the predictions from classical theory of heterogeneous nucleation imposing a quasi-static bubble evolution. When the pressure drop is significantly higher than the critical value, a liquid microlayer appears between the bubble and the wall. In this regime, the interface outside the microlayer grows at an asymptotic velocity that can be predicted from the Rayleigh--Plesset equation, while the contact line evolves with another asymptotic velocity that scales with a visco-capillary velocity that obeys the Cox--Voinov law. In general, three distinctive regions can be distinguished: the region very close to the contact line where dynamics is governed by visco-capillary effects, an intermediate region controlled by inertio-viscous effects away from the contact line yet inside the viscous boundary layer, and the region outside the boundary layer dominated by inertial effects. The microlayer forms in a regime where the capillary effects are confined in a region much smaller than the viscous boundary layer thickness. In this regime, the global capillary number takes values much larger then the critical capillary number for bubble nucleation, and the microlayer height is controlled by viscous effects and not surface tension. △ Less

Submitted 27 May, 2024; v1 submitted 12 April, 2024; originally announced April 2024.

Journal ref: Journal of Fluid Mechanics. 2024;984:A70

An Edge-based Interface Tracking (EBIT) Method for Multiphase Flows with Phase Change

Authors: Tian Long, Jieyun Pan, Stéphane Zaleski

Abstract: In this paper, the Edge-Based Interface Tracking (EBIT) method is extended to simulate multiphase flows with phase change. As a novel Front-Tracking method, the EBIT method binds interfacial markers to the Eulerian grid to achieve automatic parallelization. To include phase change effects, the energy equation for each phase is solved, with the temperature boundary condition at the interface sharpl… ▽ More In this paper, the Edge-Based Interface Tracking (EBIT) method is extended to simulate multiphase flows with phase change. As a novel Front-Tracking method, the EBIT method binds interfacial markers to the Eulerian grid to achieve automatic parallelization. To include phase change effects, the energy equation for each phase is solved, with the temperature boundary condition at the interface sharply imposed. When using collocated grids, the cell-centered velocity is approximately projected. This will lead to unphysical oscillations in the presence of phase change, as the velocity will be discontinuous across the interface. It is demonstrated that this issue can be addressed by using the ghost fluid method, in which the ghost velocity is set according to the jump condition, thereby removing the discontinuity. A series of benchmark tests are performed to validate the present method. It is shown that the numerical results agree very well with the theoretical solutions and the experimental results. △ Less

Submitted 21 February, 2024; originally announced February 2024.

On the dynamics of a collapsing bubble in contact with a rigid wall

Authors: M Saini, E Tanne, M Arrigoni, S Zaleski, D Fuster

Abstract: This work reveals that the dynamic response of a spherical cap bubble in contact with a rigid wall depends on the effective contact angle at the instant prior to collapse. This parameter allows us to discriminate between two regimes in which the mechanisms of interaction between the collapsing bubble and its surrounding medium differ significantly: When the contact angle is smaller than 90 degrees… ▽ More This work reveals that the dynamic response of a spherical cap bubble in contact with a rigid wall depends on the effective contact angle at the instant prior to collapse. This parameter allows us to discriminate between two regimes in which the mechanisms of interaction between the collapsing bubble and its surrounding medium differ significantly: When the contact angle is smaller than 90 degrees a classical jet directed towards the wall is observed whereas if the initial contact angle is larger than 90 degrees an annular re-entrant jet parallel to the wall appears. We show that this change of the behaviour can be explained using the impulse potential flow theory for small times which shows the presence of a singularity on the initial acceleration of the contact line when the contact angle is larger then 90 degrees. Direct Numerical Simulations show that although viscosity regularises the solution at $t > 0$, the solution remains singular at $t=0$. In these circumstances numerical and experimental results show that the collapse of flat bubbles can eventually lead to the formation of a vortex ring that unexpectedly induces long-range effects. The role of the bubble geometry at the instant of maximum expansion on the overall collapse process is shown to be well captured by the impulse potential flow theory, which can be easily generalised to other bubble shapes. These results may find direct application in the interpretation of geophysical flows as well as the control and design of bio-medical, naval, manufacturing and sonochemistry applications. △ Less

Submitted 10 January, 2024; originally announced January 2024.

Journal ref: J. Fluid Mech. (2022);948:A45

A hybrid continuum surface force for the three-phase VOF method

Authors: Chunheng Zhao, Jacob Maarek, Seyed Mohammadamin Taleghani, Stephane Zaleski

Abstract: We propose a hybrid continuum surface force (CSF) formulation to model the interface interaction within the three-phase volume of fluid (VOF) method. Instead of employing the height function globally, we compute the curvature based on a smooth fraction function near the region of the triple contact line. In addition, we apply the isotropic finite difference method to calculate derivatives, and the… ▽ More We propose a hybrid continuum surface force (CSF) formulation to model the interface interaction within the three-phase volume of fluid (VOF) method. Instead of employing the height function globally, we compute the curvature based on a smooth fraction function near the region of the triple contact line. In addition, we apply the isotropic finite difference method to calculate derivatives, and the current scheme readily accommodates adaptive mesh refinement, greatly enhancing efficiency. We rigorously validate the hybrid CSF using two benchmark problems that have received limited attention in previous studies of the three-phase VOF method. Using the hybrid CSF method, we accurately predict the behavior of a liquid lens under specific surface tension ratios. Furthermore, the simulation results of the equilibrium morphology of two contacting droplets are consistent with the theoretical expectations. △ Less

Submitted 19 October, 2023; originally announced October 2023.

An Edge-based Interface Tracking (EBIT) Method for Multiphase-flows Simulation with Surface Tension

Authors: Jieyun Pan, Tian Long, Leonardo Chirco, Ruben Scardovelli, Stéphane Popinet, Stéphane Zaleski

Abstract: We present a novel Front-Tracking method, the Edge-Based Interface Tracking (EBIT) method for multiphase flow simulations. In the EBIT method, the markers are located on the grid edges and the interface can be reconstructed without storing the connectivity of the markers. This feature makes the process of marker addition or removal easier than in the traditional Front-Tracking method. The EBIT met… ▽ More We present a novel Front-Tracking method, the Edge-Based Interface Tracking (EBIT) method for multiphase flow simulations. In the EBIT method, the markers are located on the grid edges and the interface can be reconstructed without storing the connectivity of the markers. This feature makes the process of marker addition or removal easier than in the traditional Front-Tracking method. The EBIT method also allows almost automatic parallelization due to the lack of explicit connectivity. In a previous journal article we have presented the kinematic part of the EBIT method, that includes the algorithms for interface linear reconstruction and advection. Here, we complete the presentation of the EBIT method and combine the kinematic algorithm with a Navier--Stokes solver. To identify the reference phase and to distinguish ambiguous topological configurations, we introduce a new feature: the Color Vertex. For the coupling with the Navier--Stokes equations, we first calculate volume fractions from the position of the markers and the Color Vertex, then viscosity and density fields from the computed volume fractions and finally surface tension stresses with the Height-Function method. In addition, an automatic topology change algorithm is implemented into the EBIT method, making it possible the simulation of more complex flows. A two-dimensional version of the EBIT method has been implemented in the open-source Basilisk platform, and validated with five standard test cases: (1) translation with uniform velocity, (2) single vortex, (3) capillary wave, (4) Rayleigh-Taylor instability and (5) rising bubble. The results are compared with those obtained with the Volume-of-Fluid (VOF) method already implemented in Basilisk. △ Less

Submitted 1 September, 2023; originally announced September 2023.

General wetting energy boundary condition in a fully explicit non-ideal fluids solver

Authors: Chunheng Zhao, Alexandre Limare, Stephane Zaleski

Abstract: We present an explicit finite difference method to simulate the non-ideal multi-phase fluid flow. The local density and the momentum transport are modeled by the Navier-Stokes (N-S) equations and the pressure is computed by the Van der Waals equation of the state (EOS). The static droplet and the dynamics of liquid-vapor separation simulations are performed as validations of this numerical scheme.… ▽ More We present an explicit finite difference method to simulate the non-ideal multi-phase fluid flow. The local density and the momentum transport are modeled by the Navier-Stokes (N-S) equations and the pressure is computed by the Van der Waals equation of the state (EOS). The static droplet and the dynamics of liquid-vapor separation simulations are performed as validations of this numerical scheme. In particular, to maintain the thermodynamic consistency, we propose a general wetting energy boundary condition at the contact line between fluids and the solid boundary. We conduct a series of comparisons between the current boundary condition and the constant contact angle boundary condition as well as the stress-balanced boundary condition. This boundary condition alleviates the instability induced by the constant contact angle boundary condition at $θ\approx0 $ and $θ\approx π$. Using this boundary condition, the equilibrium contact angle is correctly recovered and the contact line dynamics are consistent with the simulation by applying a stress-balanced boundary condition. Nevertheless, unlike the stress-balanced boundary condition for which we need to further introduce the interface thickness parameter, the current boundary condition implicitly incorporates the interface thickness information into the wetting energy. △ Less

Submitted 10 July, 2023; originally announced July 2023.

Characterizing Interface Topology in Multiphase Flows using Skeletons

Authors: Xianyang Chen, Jiacai Lu, Stéphane Zaleski, Grétar Tryggvason

Abstract: The unsteady motion of a gas-liquid interface, such as during splashing or atomization, often results in complex liquid structures embedded in the ambient fluid. Here we explore the use of skeletonization to identify the minimum amount of information needed to describe their geometry. We skeletonize a periodic liquid jet by a modification of a recently introduced approach to coarsen multiphase flo… ▽ More The unsteady motion of a gas-liquid interface, such as during splashing or atomization, often results in complex liquid structures embedded in the ambient fluid. Here we explore the use of skeletonization to identify the minimum amount of information needed to describe their geometry. We skeletonize a periodic liquid jet by a modification of a recently introduced approach to coarsen multiphase flows while retaining a sharp interface. The process consists of diffusing an index function and at the same time moving the interfaces with it, until they "collapse" into each other and form skeletons. The skeleton represents the basic topology of the jet and we also keep track of how much the interface is moved (or how much volume is "accumulated") during the process, which can be used to approximately reconstruct the jet. We explore various quantitative measures to characterize and distinguish the skeletons. Those include standard morphometrics such as branch length distribution, after segmenting the skeletons into branches, and a more sophisticated representation of the skeleton structures called Topology Morphology Descriptor (TMD), to obtain an "equivalent" description of the skeletons by retaining information about the topology in a compact way. △ Less

Submitted 12 July, 2022; originally announced July 2022.

Quality Control of Mass-Produced GEM Detectors for the CMS GE1/1 Muon Upgrade

Authors: M. Abbas, M. Abbrescia, H. Abdalla, A. Abdelalim, S. AbuZeid, A. Agapitos, A. Ahmad, A. Ahmed, W. Ahmed, C. Aimè, C. Aruta, I. Asghar, P. Aspell, C. Avila, J. Babbar, Y. Ban, R. Band, S. Bansal, L. Benussi, T. Beyrouthy, V. Bhatnagar, M. Bianco, S. Bianco, K. Black, L. Borgonovi , et al. (157 additional authors not shown)

Abstract: The series of upgrades to the Large Hadron Collider, culminating in the High Luminosity Large Hadron Collider, will enable a significant expansion of the physics program of the CMS experiment. However, the accelerator upgrades will also make the experimental conditions more challenging, with implications for detector operations, triggering, and data analysis. The luminosity of the proton-proton co… ▽ More The series of upgrades to the Large Hadron Collider, culminating in the High Luminosity Large Hadron Collider, will enable a significant expansion of the physics program of the CMS experiment. However, the accelerator upgrades will also make the experimental conditions more challenging, with implications for detector operations, triggering, and data analysis. The luminosity of the proton-proton collisions is expected to exceed $2-3\times10^{34}$~cm$^{-2}$s$^{-1}$ for Run 3 (starting in 2022), and it will be at least $5\times10^{34}$~cm$^{-2}$s$^{-1}$ when the High Luminosity Large Hadron Collider is completed for Run 4. These conditions will affect muon triggering, identification, and measurement, which are critical capabilities of the experiment. To address these challenges, additional muon detectors are being installed in the CMS endcaps, based on Gas Electron Multiplier technology. For this purpose, 161 large triple-Gas Electron Multiplier detectors have been constructed and tested. Installation of these devices began in 2019 with the GE1/1 station and will be followed by two additional stations, GE2/1 and ME0, to be installed in 2023 and 2026, respectively. The assembly and quality control of the GE1/1 detectors were distributed across several production sites around the world. We motivate and discuss the quality control procedures that were developed to standardize the performance of the detectors, and we present the final results of the production. Out of 161 detectors produced, 156 detectors passed all tests, and 144 detectors are now installed in the CMS experiment. The various visual inspections, gas tightness tests, intrinsic noise rate characterizations, and effective gas gain and response uniformity tests allowed the project to achieve this high success rate. △ Less

Submitted 22 March, 2022; originally announced March 2022.

Comments: 45 pages, 39 figures, submitted to Nuclear Instruments and Methods in Physics Research Section A

Bags mediated film atomization in a cough machine

Authors: Pallav Kant, César Pairetti, Youssef Saade, Stéphane Popinet, Stéphane Zaleski, Detlef Lohse

Abstract: We combine experiments and numerical computations to examine underlying fluid mechanical processes associated with bioaerosol generation during violent respiratory manoeuvres, such as coughing or sneezing. Analogous experiments performed in a cough machine -- consisting of a strong shearing airflow over a thin liquid film, allow us to illustrate the changes in film topology as it disintegrates int… ▽ More We combine experiments and numerical computations to examine underlying fluid mechanical processes associated with bioaerosol generation during violent respiratory manoeuvres, such as coughing or sneezing. Analogous experiments performed in a cough machine -- consisting of a strong shearing airflow over a thin liquid film, allow us to illustrate the changes in film topology as it disintegrates into small droplets. We identify that aerosol generation during the shearing of the liquid film is mediated by the formation of inflated bag-like structures. The breakup of these bags is triggered by the appearance of retracting holes that puncture the bag surface. Consequently, the cascade from inflated bags to droplets is primarily controlled by the dynamics and stability of liquid rims bounding these retracting holes. We also reveal the stabilizing role of fluid viscosity that eventually leads to the generation of smaller droplets. △ Less

Submitted 6 July, 2023; v1 submitted 28 February, 2022; originally announced February 2022.

An Edge-Based Interface-Tracking Method for Multiphase Flows

Authors: Leonardo Chirco, Stephane Zaleski

Abstract: We propose a novel class of Edge-Based Interface-Tracking (EBIT) methods in the field of multiphase flows for advecting the interface. The position of the interface is tracked by marker points located on the edges of the underlying grid, making the method flexible with respect to the choice of spatial discretization and suitable for parallel computation. In this paper we present a simple EBIT meth… ▽ More We propose a novel class of Edge-Based Interface-Tracking (EBIT) methods in the field of multiphase flows for advecting the interface. The position of the interface is tracked by marker points located on the edges of the underlying grid, making the method flexible with respect to the choice of spatial discretization and suitable for parallel computation. In this paper we present a simple EBIT method based on two-dimensional Cartesian grids and on a linear interface representation. △ Less

Submitted 5 July, 2022; v1 submitted 14 February, 2022; originally announced February 2022.

Comments: 8 pages, 5 figures

Nanoscale sheared droplet: Volume-of-Fluid, phase-field and no-slip molecular dynamics

Authors: Uǧis Lācis, Michele Pellegrino, Johan Sundin, Gustav Amberg, Stephané Zaleski, Berk Hess, Shervin Bagheri

Abstract: The motion of the three-phase contact line between two immiscible fluids and a solid surface arises in a variety of wetting phenomena and technological applications. One challenge in continuum theory is the effective representation of molecular phenomena close to the contact line. Here, we characterize the molecular processes of the moving contact line to assess the accuracy of two different conti… ▽ More The motion of the three-phase contact line between two immiscible fluids and a solid surface arises in a variety of wetting phenomena and technological applications. One challenge in continuum theory is the effective representation of molecular phenomena close to the contact line. Here, we characterize the molecular processes of the moving contact line to assess the accuracy of two different continuum two-phase models. Specifically, molecular dynamics (MD) simulations of a two-dimensional droplet between two moving plates are used to create reference data for different capillary numbers and contact angles. We use a simple-point-charge/extended (SPC/E) water model with particle-mesh Ewald electrostatics treatment. This model provides a very small slip and a more realistic representation of the molecular physics than Lennards-Jones models. The Cahn-Hilliard phase-field model and the Volume-of-Fluid model are calibrated against the drop displacement from MD reference data. It is demonstrated that the calibrated continuum models can accurately capture droplet displacement and droplet breakup for different capillary numbers and contact angles. However, we also observe differences between continuum and atomistic simulations in describing the transient and unsteady droplet behavior, in particular, close to dynamical wetting transitions. The molecular dynamics of the sheared droplet provide insight of the line friction experienced by the advancing and receding contact lines and evidence of large-scale temporal "stick-slip" like oscillations. The presented results will serve as a step** stone towards develo** accurate continuum models for nanoscale hydrodynamics. △ Less

Submitted 12 April, 2022; v1 submitted 17 December, 2021; originally announced December 2021.

Comments: 45 pages, 23 figures, 4 tables, 1 supplementary PDF, 2 supplementary movies, 1 supplementary archive, accepted for publication in "Journal of Fluid Mechanics"

Manifold death: a Volume of Fluid implementation of controlled topological changes in thin sheets by the signature method

Authors: Leonardo Chirco, Jacob Maarek, Stephane Popinet, Stephane Zaleski

Abstract: A well-known drawback of the Volume-Of-Fluid (VOF) method is that the breakup of thin liquid films or filaments is mainly caused by numerical aspects rather than by physical ones. The rupture of thin films occurs when their thickness reaches the order of the grid size and by refining the grid the breakup events are delayed. When thin filaments rupture, many droplets are generated due to the mass c… ▽ More A well-known drawback of the Volume-Of-Fluid (VOF) method is that the breakup of thin liquid films or filaments is mainly caused by numerical aspects rather than by physical ones. The rupture of thin films occurs when their thickness reaches the order of the grid size and by refining the grid the breakup events are delayed. When thin filaments rupture, many droplets are generated due to the mass conserving properties of VOF. Thus, the numerical character of the breakup does not allow obtaining the desired convergence of the droplet size distribution under grid refinement. In this work, we present a novel algorithm to detect and perforate thin structures. First, thin films or ligaments are identified by taking quadratic moments of an indicator obtained from the volume fraction. A multiscale approach allows us to choose the critical film thickness independently of the mesh resolution. Then, the breakup is induced by making holes in the films before their thickness reaches the grid size. We show that the method improves the convergence upon grid refinement of the droplets size distribution and of enstrophy. △ Less

Submitted 24 June, 2022; v1 submitted 10 November, 2021; originally announced November 2021.

Performance of a Triple-GEM Demonstrator in $pp$ Collisions at the CMS Detector

Authors: M. Abbas, M. Abbrescia, H. Abdalla, A. Abdelalim, S. AbuZeid, A. Agapitos, A. Ahmad, A. Ahmed, W. Ahmed, C. Aimè, C. Aruta, I. Asghar, P. Aspell, C. Avila, J. Babbar, Y. Ban, R. Band, S. Bansal, L. Benussi, V. Bhatnagar, M. Bianco, S. Bianco, K. Black, L. Borgonovi, O. Bouhali , et al. (156 additional authors not shown)

Abstract: After the Phase-2 high-luminosity upgrade to the Large Hadron Collider (LHC), the collision rate and therefore the background rate will significantly increase, particularly in the high $η$ region. To improve both the tracking and triggering of muons, the Compact Muon Solenoid (CMS) Collaboration plans to install triple-layer Gas Electron Multiplier (GEM) detectors in the CMS muon endcaps. Demonstr… ▽ More After the Phase-2 high-luminosity upgrade to the Large Hadron Collider (LHC), the collision rate and therefore the background rate will significantly increase, particularly in the high $η$ region. To improve both the tracking and triggering of muons, the Compact Muon Solenoid (CMS) Collaboration plans to install triple-layer Gas Electron Multiplier (GEM) detectors in the CMS muon endcaps. Demonstrator GEM detectors were installed in CMS during 2017 to gain operational experience and perform a preliminary investigation of detector performance. We present the results of triple-GEM detector performance studies performed in situ during normal CMS and LHC operations in 2018. The distribution of cluster size and the efficiency to reconstruct high $p_T$ muons in proton--proton collisions are presented as well as the measurement of the environmental background rate to produce hits in the GEM detector. △ Less

Submitted 22 September, 2021; v1 submitted 20 July, 2021; originally announced July 2021.

Comments: 10 pages, 5 figures

Modeling the triple-GEM detector response to background particles for the CMS Experiment

Authors: M. Abbas, M. Abbrescia, H. Abdalla, A. Abdelalim, S. AbuZeid, A. Agapitos, A. Ahmad, A. Ahmed, W. Ahmed, C. Aimè, C. Aruta, I. Asghar, P. Aspell, C. Avila, I. Azhgirey, J. Babbar, Y. Ban, R. Band, S. Bansal, L. Benussi, V. Bhatnagar, M. Bianco, S. Bianco, K. Black, L. Borgonovi , et al. (164 additional authors not shown)

Abstract: An estimate of environmental background hit rate on triple-GEM chambers is performed using Monte Carlo (MC) simulation and compared to data taken by test chambers installed in the CMS experiment (GE1/1) during Run-2 at the Large Hadron Collider (LHC). The hit rate is measured using data collected with proton-proton collisions at 13 TeV and a luminosity of 1.5$\times10^{34}$ cm$^{-2}$ s$^{-1}$. The… ▽ More An estimate of environmental background hit rate on triple-GEM chambers is performed using Monte Carlo (MC) simulation and compared to data taken by test chambers installed in the CMS experiment (GE1/1) during Run-2 at the Large Hadron Collider (LHC). The hit rate is measured using data collected with proton-proton collisions at 13 TeV and a luminosity of 1.5$\times10^{34}$ cm$^{-2}$ s$^{-1}$. The simulation framework uses a combination of the FLUKA and Geant4 packages to obtain the hit rate. FLUKA provides the radiation environment around the GE1/1 chambers, which is comprised of the particle flux with momentum direction and energy spectra ranging from $10^{-11}$ to $10^{4}$ MeV for neutrons, $10^{-3}$ to $10^{4}$ MeV for $γ$'s, $10^{-2}$ to $10^{4}$ MeV for $e^{\pm}$, and $10^{-1}$ to $10^{4}$ MeV for charged hadrons. Geant4 provides an estimate of detector response (sensitivity) based on an accurate description of detector geometry, material composition and interaction of particles with the various detector layers. The MC simulated hit rate is estimated as a function of the perpendicular distance from the beam line and agrees with data within the assigned uncertainties of 10-14.5%. This simulation framework can be used to obtain a reliable estimate of background rates expected at the High Luminosity LHC. △ Less

Submitted 8 July, 2021; originally announced July 2021.

Comments: 16 pages, 9 figures, 6 tables

Statistics of drops generated from ensembles of randomly corrugated ligaments

Authors: Sagar Pal, Cesar Pairetti, Marco Crialesi-Esposito, Daniel Fuster, Stéphane Zaleski

Abstract: The size of drops generated by the capillary-driven disintegration of liquid ligaments plays a fundamental role in several important natural phenomena, ranging from heat and mass transfer at the ocean-atmosphere interface to pathogen transmission. The inherent non-linearity of the equations governing the ligament destabilization leads to significant differences in the resulting drop sizes, owing t… ▽ More The size of drops generated by the capillary-driven disintegration of liquid ligaments plays a fundamental role in several important natural phenomena, ranging from heat and mass transfer at the ocean-atmosphere interface to pathogen transmission. The inherent non-linearity of the equations governing the ligament destabilization leads to significant differences in the resulting drop sizes, owing to small fluctuations in the myriad initial conditions. Previous experiments and simulations reveal a variety of drop size distributions, corresponding to competing underlying physical interpretations. Here, we perform numerical simulations of individual ligaments, the deterministic breakup of which is triggered by random initial surface corrugations. The simulations are grouped in a large ensemble, each corresponding to a random initial configuration. The resulting probability distributions reveal three stable drop sizes, generated via a sequence of two distinct stages of breakup. Four different distributions are tested, volume-based Poisson, Gaussian, Gamma and Log-Normal. Depending on the time, range of droplet sizes and criteria for success, each distribution has successes and failures. However the Log-Normal distribution roughly describes the data when fitting both the primary peak and the tail of the distribution while the number of droplets generated is the highest, while the Gamma and Log-Normal distributions perform equally well when fitting the tail. The study demonstrates a precisely controllable and reproducible framework, which can be employed to investigate the mechanisms responsible for the polydispersity of drop sizes found in complex fluid fragmentation scenarios. △ Less

Submitted 3 June, 2024; v1 submitted 30 June, 2021; originally announced June 2021.

Roughness on liquid-infused surfaces induced by capillary waves

Authors: Johan Sundin, Stéphane Zaleski, Shervin Bagheri

Abstract: Liquid-infused surfaces (LIS) are a promising technique for reducing friction, fouling and icing in both laminar and turbulent flows. Previous work has demonstrated that these surfaces are susceptible to shear-driven drainage. Here, we report a different failure mode using direct numerical simulations of a turbulent channel flow with liquid-infused longitudinal grooves. When the liquid-liquid surf… ▽ More Liquid-infused surfaces (LIS) are a promising technique for reducing friction, fouling and icing in both laminar and turbulent flows. Previous work has demonstrated that these surfaces are susceptible to shear-driven drainage. Here, we report a different failure mode using direct numerical simulations of a turbulent channel flow with liquid-infused longitudinal grooves. When the liquid-liquid surface tension is small and/or grooves are wide, we observe traveling-wave perturbations on the interface with amplitudes larger than the viscous sublayer of the turbulent flow. These capillary waves induce a roughness effect that increases drag. The generation mechanism of these waves is explained using the theory developed by Miles for gravity waves. Energy is transferred from the turbulent flow to the LIS provided that there is a negative curvature of the mean flow at the critical layer. Given the groove width, the Weber number and an estimate of the friction Reynolds number, we provide relations to determine whether a LIS behaves as a smooth or rough surface in a turbulent flow. △ Less

Submitted 12 April, 2021; v1 submitted 2 February, 2021; originally announced February 2021.

Journal ref: J. Fluid Mech. 915 (2021) R6

A numerical cough machine

Authors: Cesar Pairetti, Raphaël Villiers, Stéphane Zaleski

Abstract: We introduce a simplified model of physiological coughing or sneezing, in the form of a thin liquid layer subject to a rapid (30 m/s) air stream. The setup is simulated using the Volume-Of-Fluid method with octree mesh adaptation, the latter allowing grid sizes small enough to capture the Kolmogorov length scale. The results confirm the trend to an intermediate distribution between a Log-Normal an… ▽ More We introduce a simplified model of physiological coughing or sneezing, in the form of a thin liquid layer subject to a rapid (30 m/s) air stream. The setup is simulated using the Volume-Of-Fluid method with octree mesh adaptation, the latter allowing grid sizes small enough to capture the Kolmogorov length scale. The results confirm the trend to an intermediate distribution between a Log-Normal and a Pareto distribution $P(d) \propto d^{-3.3}$ for the distribution of droplet sizes in agreement with a previous re-analysis of experimental results by one of the authors. The mechanism of atomisation does not differ qualitatively from the multiphase mixing layer experiments and simulations. No mechanism for a bimodal distribution, also sometimes observed, is evidenced in these simulations. △ Less

Submitted 15 January, 2021; v1 submitted 14 January, 2021; originally announced January 2021.

A novel momentum-conserving, mass-momentum consistent method for interfacial flows involving large density contrasts

Authors: Sagar Pal, Daniel Fuster, Stéphane Zaleski

Abstract: We propose a novel method for the direct numerical simulation of interfacial flows involving large density contrasts, using a Volume-of-Fluid method. We employ the conservative formulation of the incompressible Navier-Stokes equations for immiscible fluids in order to ensure consistency between the discrete transport of mass and momentum in both fluids. This strategy is implemented on a uniform 3D… ▽ More We propose a novel method for the direct numerical simulation of interfacial flows involving large density contrasts, using a Volume-of-Fluid method. We employ the conservative formulation of the incompressible Navier-Stokes equations for immiscible fluids in order to ensure consistency between the discrete transport of mass and momentum in both fluids. This strategy is implemented on a uniform 3D Cartesian grid with a staggered configuration of primitive variables, wherein a geometrical reconstruction based mass advection is carried out on a grid twice as fine as that for the momentum. The implementation is in the spirit of Rudman (1998) [41], coupled with the extension of the direction-split time integration scheme of Weymouth & Yue (2010) [46] to that of conservative momentum transport. The resulting numerical method ensures discrete consistency between the mass and momentum propagation, while simultaneously enforcing conservative numerical transport to arbitrary levels of precision in 3D. We present several quantitative comparisons with benchmarks from existing literature in order to establish the accuracy of the method, and henceforth demonstrate its stability and robustness in the context of a complex turbulent interfacial flow configuration involving a falling raindrop in air. △ Less

Submitted 11 January, 2021; originally announced January 2021.

PArallel, Robust, Interface Simulator (PARIS)

Authors: W. Aniszewski, T. Arrufat, M. Crialesi-Esposito, S. Dabiri, D. Fuster, Y. Ling, J. Lu, L. Malan, S. Pal, R. Scardovelli, G. Tryggvason, P. Yecko, S. Zaleski

Abstract: Paris (PArallel, Robust, Interface Simulator) is a finite volume code for simulations of immiscible multifluid or multiphase flows. It is based on the "one-fluid" formulation of the Navier-Stokes equations where different fluids are treated as one material with variable properties, and surface tension is added as a singular interface force. The fluid equations are solved on a regular structured st… ▽ More Paris (PArallel, Robust, Interface Simulator) is a finite volume code for simulations of immiscible multifluid or multiphase flows. It is based on the "one-fluid" formulation of the Navier-Stokes equations where different fluids are treated as one material with variable properties, and surface tension is added as a singular interface force. The fluid equations are solved on a regular structured staggered grid using an explicit projection method with a first-order or second-order time integration scheme. The interface separating the different fluids is tracked by a Front-Tracking (FT) method, where the interface is represented by connected marker points, or by a Volume-of-Fluid (VOF) method, where the marker function is advected directly on the fixed grid. Paris is written in Fortran95/2002 and parallelized using MPI and domain decomposition. It is based on several earlier FT or VOF codes such as Ftc3D, Surfer or Gerris. These codes and similar ones, as well as Paris, have been used to simulate a wide range of multifluid and multiphase flows. △ Less

Submitted 21 December, 2020; originally announced December 2020.

Interstrip Capacitances of the Readout Board used in Large Triple-GEM Detectors for the CMS Muon Upgrade

Authors: M. Abbas, M. Abbrescia, H. Abdalla, A. Abdelalim, S. AbuZeid, A. Agapitos, A. Ahmad, A. Ahmed, W. Ahmed, C. Aimè, C. Aruta, I. Asghar, P. Aspell, C. Avila, J. Babbar, Y. Ban, R. Band, S. Bansal, L. Benussi, V. Bhatnagar, M. Bianco, S. Bianco, K. Black, L. Borgonovi, O. Bouhali , et al. (156 additional authors not shown)

Abstract: We present analytical calculations, Finite Element Analysis modeling, and physical measurements of the interstrip capacitances for different potential strip geometries and dimensions of the readout boards for the GE2/1 triple-Gas Electron Multiplier detector in the CMS muon system upgrade. The main goal of the study is to find configurations that minimize the interstrip capacitances and consequent… ▽ More We present analytical calculations, Finite Element Analysis modeling, and physical measurements of the interstrip capacitances for different potential strip geometries and dimensions of the readout boards for the GE2/1 triple-Gas Electron Multiplier detector in the CMS muon system upgrade. The main goal of the study is to find configurations that minimize the interstrip capacitances and consequently maximize the signal-to-noise ratio for the detector. We find agreement at the 1.5--4.8% level between the two methods of calculations and on the average at the 17% level between calculations and measurements. A configuration with halved strip lengths and doubled strip widths results in a measured 27--29% reduction over the original configuration while leaving the total number of strips unchanged. We have now adopted this design modification for all eight module types of the GE2/1 detector and will produce the final detector with this new strip design. △ Less

Submitted 20 September, 2020; originally announced September 2020.

Comments: 22 pages, 14 figures

Journal ref: 2020 JINST 15 P12019

Host-to-Host Airborne Transmission As a Multiphase Flow Problem For Science-Based Social Distance Guidelines

Authors: S. Balachandar, S. Zaleski, A. Soldati, G. Ahmadi, L. Bourouiba

Abstract: COVID-19 pandemic has strikingly demonstrated how important it is to develop fundamental knowledge related to generation, transport and inhalation of pathogen-laden droplets and their subsequent possible fate as airborne particles, or aerosols, in the context of human to human transmission. It is also increasingly clear that airborne transmission is an important contributor to rapid spreading of t… ▽ More COVID-19 pandemic has strikingly demonstrated how important it is to develop fundamental knowledge related to generation, transport and inhalation of pathogen-laden droplets and their subsequent possible fate as airborne particles, or aerosols, in the context of human to human transmission. It is also increasingly clear that airborne transmission is an important contributor to rapid spreading of the disease. In this paper, we discuss the processes of droplet generation by exhalation, their potential transformation into airborne particles by evaporation, transport over long distances by the exhaled puff and by ambient air turbulence, and final inhalation by the receiving host as interconnected multiphase flow processes. A simple model for the time evolution of droplet/aerosol concentration is presented based on a theoretical analysis of the relevant physical processes. The modeling framework along with detailed experiments and simulations can be used to study a wide variety of scenarios involving breathing, talking, coughing and sneezing and in a number of environmental conditions, as humid or dry atmosphere, confined or open environment. Although a number of questions remain open on the physics of evaporation and coupling with persistence of the virus, it is clear that with a more reliable understanding of the underlying flow physics of virus transmission one can set the foundation for an improved methodology in designing case-specific social distancing and infection control guidelines. △ Less

Submitted 13 August, 2020; originally announced August 2020.

Comments: 14 figures and 40 pages

Dynamic wetting failure in curtain coating by the Volume-of-Fluid method

Authors: Tomas Fullana, Stéphane Zaleski, Stéphane Popinet

Abstract: In this paper we investigate dynamic wetting in the curtain coating configuration. The two-phase Navier-Stokes equations are solved by a Volume-of-Fluid method on an adaptive Cartesian mesh. We introduce the Navier boundary condition to regularize the solution at the triple point and remove the implicit numerical slip induced by the cell-centered interface advection. We use a constant contact angl… ▽ More In this paper we investigate dynamic wetting in the curtain coating configuration. The two-phase Navier-Stokes equations are solved by a Volume-of-Fluid method on an adaptive Cartesian mesh. We introduce the Navier boundary condition to regularize the solution at the triple point and remove the implicit numerical slip induced by the cell-centered interface advection. We use a constant contact angle to describe the dynamic contact line. The resolution of the governing equations allows us to predict the substrate velocity at which wetting failure occurs. The model predictions are compared with prior computations and experimental observations. △ Less

Submitted 21 May, 2020; originally announced May 2020.

Comments: 13 pages, 11 figures, post-review version, under consideration for publication in "European Physical Journal Special Topics"

Steady moving contact line of water over a no-slip substrate

Authors: Uǧis Lācis, Petter Johansson, Tomas Fullana, Berk Hess, Gustav Amberg, Shervin Bagheri, Stephané Zaleski

Abstract: The movement of the triple contact line plays a crucial role in many applications such as ink-jet printing, liquid coating and drainage (imbibition) in porous media. To design accurate computational tools for these applications, predictive models of the moving contact line are needed. However, the basic mechanisms responsible for movement of the triple contact line are not well understood but stil… ▽ More The movement of the triple contact line plays a crucial role in many applications such as ink-jet printing, liquid coating and drainage (imbibition) in porous media. To design accurate computational tools for these applications, predictive models of the moving contact line are needed. However, the basic mechanisms responsible for movement of the triple contact line are not well understood but still debated. We investigate the movement of the contact line between water, vapour and a silica-like solid surface under steady conditions in low capillary number regime. We use molecular dynamics (MD) with an atomistic water model to simulate a nanoscopic drop between two moving plates. We include hydrogen bonding between the water molecules and the solid substrate, which leads to a sub-molecular slip length. We benchmark two continuum methods, the Cahn-Hilliard phase-field (PF) model and a volume-of-fluid (VOF) model, against MD results. We show that both continuum models can reproduce the statistical measures obtained from MD reasonably well, with a trade-off in accuracy. We demonstrate the importance of the phase field mobility parameter and the local slip length in accurately modelling the moving contact line. △ Less

Submitted 5 April, 2020; v1 submitted 27 March, 2020; originally announced March 2020.

Comments: 26 pages, 13 figures, 4 tables, post-review version, under consideration for publication in "European Physical Journal Special Topics"

Short-term oscillation and falling dynamics for a water drop drip** in quiescent air

Authors: Bo Zhang, Pei-Hsun Tsai, An-Bang Wang, Stéphane Popinet, Stéphane Zaleski, Yue Ling

Abstract: The short-term transient falling dynamics of a drip** water drop in quiescent air has been investigated through both simulation and experiment. The focus is on the short term behavior and the time range considered covers about eight dominant second-mode oscillations of the drop after it is formed. Due to the small fluid inertia the growth of the drop is quasi-static and is well captured by the s… ▽ More The short-term transient falling dynamics of a drip** water drop in quiescent air has been investigated through both simulation and experiment. The focus is on the short term behavior and the time range considered covers about eight dominant second-mode oscillations of the drop after it is formed. Due to the small fluid inertia the growth of the drop is quasi-static and is well captured by the static pendant drop theory. Nevertheless, the pinching dynamics and the resulting post-formation state of the drop trigger a nonlinear oscillation when the drop falls. The initial shape of the drop when it is just formed is decomposed into spherical harmonic modes. The pinching dynamics such as interface overturning introduces small-scale variation on the drop contour, which in turn contributes to the finite amplitudes of the higher-order modes. Furthermore, the initial kinetic energy when the droplet is just formed is as important as the initial surface energy contained in the drop shape, and is found to amplify the initial oscillation amplitude and to induce a phase shift in the oscillation of all the modes. By incorporating both the initial surface and kinetic energy, the linear model for a free drop oscillation yields very good predictions for the second and third modes. The mode amplitude spectra show both the primary frequencies that are consistent with the Lamb's theory and the secondary frequencies arising from different modes due to nonlinear inter-mode coupling. The complex transient flow inside and outside the drop is induced by the interaction between the falling motion and the nonlinear oscillation. The streamlines indicate that the internal flow is substantially different from the Hill vortex for a falling drop without oscillation. The temporal evolutions of both the internal flow and the wake morphology follow the dominant second oscillation mode. △ Less

Submitted 17 March, 2020; originally announced March 2020.

Journal ref: Physical Review Fluids 4, (2019) 123604

A geometric vof method for interface resolved phase change and conservative thermal energy advection

Authors: L. C. Malan, A. G. Malan, S. Zaleski, P. G. Rousseau

Abstract: We present a novel numerical method to solve the incompressible Navier-Stokes equations for two-phase flows with phase change, using a one-fluid approach. Separate phases are tracked using a geometric Volume-Of-Fluid (VOF) method with piecewise linear interface construction (PLIC). Thermal energy advection is treated in conservative form and the geometric calculation of VOF fluxes at computational… ▽ More We present a novel numerical method to solve the incompressible Navier-Stokes equations for two-phase flows with phase change, using a one-fluid approach. Separate phases are tracked using a geometric Volume-Of-Fluid (VOF) method with piecewise linear interface construction (PLIC). Thermal energy advection is treated in conservative form and the geometric calculation of VOF fluxes at computational cell boundaries is used consistently to calculate the fluxes of heat capacity. The phase boundary is treated as sharp (infinitely thin), which leads to a discontinuity in the velocity field across the interface in the presence of phase change. The numerical difficulty of this jump is accommodated with the introduction of a novel two-step VOF advection scheme. The method has been implemented in the open source code PARIS and is validated using well-known test cases. These include an evaporating circular droplet in microgravity (2D), the Stefan problem and a 3D bubble in superheated liquid. The accuracy shown in the results were encouraging. The 2D evaporating droplet showed excellent prediction of the droplet volume evolution as well as preservation of its circular shape. A relative error of less than 1% was achieved for the Stefan problem case, using water properties at atmospheric conditions. For the final radius of the bubble in superheated liquid at a Jacob number of 0.5, a relative error of less than 6% was obtained on the coarsest grid, with less than 1% on the finest. △ Less

Submitted 10 January, 2020; originally announced January 2020.

Improved Spectral Imaging Microscopy for Cultural Heritage through Oblique Illumination

Authors: Lindsay Oakley, Stephanie Zaleski, Billie Males, Ollie Cossairt, Marc Walton

Abstract: This work presents the development of a flexible microscopic chemical imaging platform for cultural heritage that utilizes wavelength-tunable oblique illumination from a point source to obtain per-pixel reflectance spectra in the VIS-NIR range. The microscope light source can be adjusted on two axes allowing for a hemisphere of possible illumination directions. The synthesis of multiple illuminati… ▽ More This work presents the development of a flexible microscopic chemical imaging platform for cultural heritage that utilizes wavelength-tunable oblique illumination from a point source to obtain per-pixel reflectance spectra in the VIS-NIR range. The microscope light source can be adjusted on two axes allowing for a hemisphere of possible illumination directions. The synthesis of multiple illumination angles allows for the calculation of surface normal vectors, similar to phase gradients, and axial optical sectioning. The extraction of spectral reflectance images with high spatial resolutions from these data is demonstrated through the analysis of a replica cross-section, created from known painting reference materials, as well as a sample extracted from a painting by Pablo Picasso entitled La Miséreuse accroupie (1902). These case studies show the rich microscale molecular information that may be obtained using this microscope and how the instrument overcomes challenges for spectral analysis commonly encountered on works of art with complex matrices composed of both inorganic minerals and organic lakes. △ Less

Submitted 1 January, 2020; originally announced January 2020.

Density contrast matters for drop fragmentation thresholds at low Ohnesorge number

Authors: Florence Marcotte, Stéphane Zaleski

Abstract: We address numerically the deformation and fragmentation dynamics of a single liquid drop subject to impulsive acceleration by a unidirectional gas stream. The density ratio between the liquid and gaseous phases is varied in the $10-2000$ range and comparisons are made with recent drop breakup experiments. We show for low Ohnesorge numbers that the liquid-gas density contrast significantly modifie… ▽ More We address numerically the deformation and fragmentation dynamics of a single liquid drop subject to impulsive acceleration by a unidirectional gas stream. The density ratio between the liquid and gaseous phases is varied in the $10-2000$ range and comparisons are made with recent drop breakup experiments. We show for low Ohnesorge numbers that the liquid-gas density contrast significantly modifies the critical Weber number for the transition between bursting and strip** fragmentation regimes, on the one hand, and for drop fragmentation, on the other hand. We suggest a simple theoretical argument to predict the transitional Weber number as a function of the density contrast and show that the stabilising influence of small contrasts can be explained by inertial effects in the nonlinear coupling between drop stretching and centroid acceleration. △ Less

Submitted 25 November, 2019; v1 submitted 24 July, 2019; originally announced July 2019.

Journal ref: Phys. Rev. Fluids, 4, 103604 (2019)

Planar Jet Strip** of Liquid Coatings: Numerical Studies

Authors: Wojciech Aniszewski, Stéphane Zaleski, Stéphane Popinet, Youssef Saade

Abstract: In this paper, we present a detailed example of numerical study of flm formation in the context of metal coating. Subsequently we simulate wi** of the film by a planar jet. The simulations have been performed using Basilisk, a grid-adapting, strongly optimized code. Mesh adaptation allows for arbitrary precision in relevant regions such as the contact line or the liquid-air impact zone, while co… ▽ More In this paper, we present a detailed example of numerical study of flm formation in the context of metal coating. Subsequently we simulate wi** of the film by a planar jet. The simulations have been performed using Basilisk, a grid-adapting, strongly optimized code. Mesh adaptation allows for arbitrary precision in relevant regions such as the contact line or the liquid-air impact zone, while coarse grid is applied elsewhere. This, as the results indicate, is the only realistic approach for a numerical method to cover the wide range of necessary scales from the predicted film thickness (tens of microns) to the domain size (meters). The results suggest assumptions of laminar flow inside the film are not justified for heavy coats (liquid zinc). As for the wi**, our simulations supply a great amount of instantaneous results concerning initial film atomization as well as film thickness. △ Less

Submitted 17 July, 2019; originally announced July 2019.

Comments: 20 pages, 20 figures

A phase inversion benchmark for multiscale multiphase flows

Authors: J. -L. Estivalezes, W. Aniszewski, F. Auguste, Y. Ling, L. Osmar, J. -P. Caltagirone, L. Chirco, A. Pedrono, S. Popinet, A. Berlemont, J. Magnaudet, T. Menard, S. Vincent, S. Zaleski

Abstract: A series of benchmarks based on the physical situation of "phase inversion" between two immiscible liquids is presented. These benchmarks aim at progressing toward the direct numerical simulation of two-phase flows. Several CFD codes developed in French laboratories and using either Volume-of-Fluid or Level-Set interface tracking methods are used to provide physical solutions of the benchmarks, co… ▽ More A series of benchmarks based on the physical situation of "phase inversion" between two immiscible liquids is presented. These benchmarks aim at progressing toward the direct numerical simulation of two-phase flows. Several CFD codes developed in French laboratories and using either Volume-of-Fluid or Level-Set interface tracking methods are used to provide physical solutions of the benchmarks, convergence studies and code comparisons. Two typical configurations are retained, with integral scale Reynolds numbers of 13.700 and 433.000, respectively. The physics of the problem are probed through macroscopic quantities such as potential and kinetic energies, or enstrophy. In addition, scaling laws for the temporal decay of the kinetic energy are derived to check the physical relevance of the simulations. Finally the droplet size distribution is probed. Additional test problems are also reported to estimate the influence of viscous effects in the vicinity of the interface. △ Less

Submitted 17 October, 2021; v1 submitted 6 June, 2019; originally announced June 2019.

Comments: 35 pages, 35 figures, third revision submitted to J. Comput. Phys

A mass-momentum consistent, Volume-of-Fluid method for incompressible flow on staggered grids

Authors: T. Arrufat, M. Crialesi-Esposito, D. Fuster, Y. Ling, L. Malan, S. Pal, R. Scardovelli, G. Tryggvason, S. Zaleski

Abstract: The computation of flows with large density contrasts is notoriously difficult. To alleviate the difficulty we consider a discretization of the Navier-Stokes equation that advects mass and momentum in a consistent manner. Incompressible flow with capillary forces is modeled and the discretization is performed on a staggered grid of Marker and Cell type. The Volume-of-Fluid method is used to track… ▽ More The computation of flows with large density contrasts is notoriously difficult. To alleviate the difficulty we consider a discretization of the Navier-Stokes equation that advects mass and momentum in a consistent manner. Incompressible flow with capillary forces is modeled and the discretization is performed on a staggered grid of Marker and Cell type. The Volume-of-Fluid method is used to track the interface and a Height-Function method is used to compute surface tension. The advection of the volume fraction is performed using either the Lagrangian-Explicit / CIAM (Calcul d'Interface Affine par Morceaux) method or the Weymouth and Yue (WY) Eulerian-Implicit method. The WY method conserves fluid mass to machine accuracy provided incompressibility is satisfied. To improve the stability of these methods momentum fluxes are advected in a manner "consistent" with the volume-fraction fluxes, that is a discontinuity of the momentum is advected at the same speed as a discontinuity of the density. To find the density on the staggered cells on which the velocity is centered, an auxiliary reconstruction of the density is performed. The method is tested for a droplet without surface tension in uniform flow, for a droplet suddenly accelerated in a carrying gas at rest at very large density ratio without viscosity or surface tension, for the Kelvin-Helmholtz instability, for a 3mm-diameter falling raindrop and for an atomizing flow in air-water conditions. △ Less

Submitted 24 February, 2021; v1 submitted 29 November, 2018; originally announced November 2018.

Journal ref: Computers & Fluids 215 (2021): 104785

A two-phase mixing layer between parallel gas and liquid streams: multiphase turbulence statistics and influence of interfacial instability

Authors: Y. Ling, D. Fuster, G. Tryggvason, S. Zaleski

Abstract: The two-phase mixing layer formed between parallel gas and liquid streams is an important fundamental problem in turbulent multiphase flows. The problem is relevant to many industrial applications and natural phenomena, such as air-blast atomizers in fuel injection systems and breaking waves in the ocean. The velocity difference between the gas and liquid streams triggers an interfacial instabilit… ▽ More The two-phase mixing layer formed between parallel gas and liquid streams is an important fundamental problem in turbulent multiphase flows. The problem is relevant to many industrial applications and natural phenomena, such as air-blast atomizers in fuel injection systems and breaking waves in the ocean. The velocity difference between the gas and liquid streams triggers an interfacial instability which can be convective or absolute depending on the stream properties and injection parameters. In the present study, a direct numerical simulation of a two-phase gas-liquid mixing layer that lie in the absolute instability regime is conducted. A dominant frequency is observed in the simulation and the numerical result agrees well with the prediction from viscous stability theory. As the interfacial wave plays a critical role in turbulence transition and development, the temporal evolution of turbulent fluctuations (such as the enstrophy) also exhibits a similar frequency. In order to investigate the statistical response of the multiphase turbulence flow, the simulation has been run for a long physical time so that time-averaging can be performed to yield the statistically converged results for Reynolds stresses and the turbulent kinetic energy (TKE) budget. An extensive mesh refinement study using from 8 million to about 4 billions cells has been carried out. The turbulent dissipation is shown to be highly demanding on mesh resolution compared to other terms in TKE budget. The results obtained with the finest mesh are shown to be not far from converged results of turbulent dissipation which allow us to obtain estimations of the Kolmogorov and Hinze scales. The computed Hinze scale is significantly larger than the size of droplets observed and does not seem to be a relevant length scale to describe the smallest size of droplets formed in atomization. △ Less

Submitted 6 August, 2018; originally announced August 2018.

Computing Curvature for Volume of Fluid Methods using Machine Learning

Authors: Yinghe Qi, Jiacai Lu, Ruben Scardovelli, Stephane Zaleski, Gretar Tryggvason

Abstract: In spite of considerable progress, computing curvature in Volume of Fluid (VOF) methods continues to be a challenge. The goal is to develop a function or a subroutine that returns the curvature in computational cells containing an interface separating two immiscible fluids, given the volume fraction in the cell and the adjacent cells. Currently, the most accurate approach is to fit a curve (2D), o… ▽ More In spite of considerable progress, computing curvature in Volume of Fluid (VOF) methods continues to be a challenge. The goal is to develop a function or a subroutine that returns the curvature in computational cells containing an interface separating two immiscible fluids, given the volume fraction in the cell and the adjacent cells. Currently, the most accurate approach is to fit a curve (2D), or a surface (3D), matching the volume fractions and finding the curvature by differentiation. Here, a different approach is examined. A synthetic data set, relating curvature to volume fractions, is generated using well-defined shapes where the curvature and volume fractions are easily found and then machine learning is used to fit the data (training). The resulting function is used to find the curvature for shapes not used for the training and implemented into a code to track moving interfaces. The results suggest that using machine learning to generate the relationship is a viable approach that results in reasonably accurate predictions. △ Less

Submitted 27 July, 2018; originally announced July 2018.

Direct Numerical Simulations of pore competition in idealized micro-spall using the VOF method

Authors: L. C. Malan, Y. Ling, R. Scardovelli, A. Llor, S. Zaleski

Abstract: Under shock loading, metals have been found to melt and with reflection of the shock wave from the material free surface, cavities nucleate and grow. This process is referred to as micro spall and has been studied experimentally with analytical models describing debris sizes. Measurements during the cavity growth phase are not possible at present and we present here the Direct Numerical Simulation… ▽ More Under shock loading, metals have been found to melt and with reflection of the shock wave from the material free surface, cavities nucleate and grow. This process is referred to as micro spall and has been studied experimentally with analytical models describing debris sizes. Measurements during the cavity growth phase are not possible at present and we present here the Direct Numerical Simulation of an idealized problem where we assume an inviscid, incompressible liquid subject to a constant expansion rate with cavities at a vanishing vapour pressure. In order to allow for a time-varying gas volume a free-surface interface condition has been implemented in an existing incompressible multiphase Navier-Stokes solver, PARIS Simulator, using a volume-of-fluid method. The gas flow remains unsolved and is instead assumed to have a fixed pressure which is applied to the liquid through a Dirichlet boundary condition on the arbitrary liquid-gas interface. Gas bubbles are tracked individually, allowing the gas pressure to be prescribed using a suitable equation of state. Simulations with hundreds of bubbles have been performed in a fixed domain under a constant rate of expansion. A bubble competition is observed: larger bubbles tend to expand more rapidly at the demise of smaller ones. The time scale of competition is shown to depend on a modified Weber number. △ Less

Submitted 13 November, 2017; originally announced November 2017.

Transition in a numerical model of contact line dynamics and forced dewetting

Authors: S. Afkhami, J. Buongiorno, A. Guion, S. Popinet, Y. Saade, R. Scardovelli, S. Zaleski

Abstract: We investigate the transition to a Landau-Levich-Derjaguin film in forced dewetting using a quadtree adaptive solution to the Navier-Stokes equations with surface tension. We use a discretization of the capillary forces near the receding contact line that yields an equilibrium for a specified contact angle $θ_Δ$ called the numerical contact angle. Despite the well-known contact line singularity, d… ▽ More We investigate the transition to a Landau-Levich-Derjaguin film in forced dewetting using a quadtree adaptive solution to the Navier-Stokes equations with surface tension. We use a discretization of the capillary forces near the receding contact line that yields an equilibrium for a specified contact angle $θ_Δ$ called the numerical contact angle. Despite the well-known contact line singularity, dynamic simulations can proceed without any explicit additional numerical procedure. We investigate angles from $15^\circ$ to $110^\circ$ and capillary numbers from $0.00085$ to $0.2$ where the mesh size $Δ$ is varied in the range of $0.0035$ to $0.06$ of the capillary length $l_c$. To interpret the results, we use Cox's theory which involves a microscopic distance $r_m$ and a microscopic angle $θ_e$. In the numerical case, the equivalent of $θ_e$ is the angle $θ_Δ$ and we find that Cox's theory also applies. We introduce the scaling factor or gauge function $φ$ so that $r_m = Δ/φ$ and estimate this gauge function by comparing our numerics to Cox's theory. The comparison provides a direct assessment of the agreement of the numerics with Cox's theory and reveals a critical feature of the numerical treatment of contact line dynamics: agreement is poor at small angles while it is better at large angles. This scaling factor is shown to depend only on $θ_Δ$ and the viscosity ratio $q$. In the case of small $θ_e$, we use the prediction by Eggers [Phys. Rev. Lett., vol. 93, pp 094502, 2004] of the critical capillary number for the Landau-Levich-Derjaguin forced dewetting transition. We generalize this prediction to large $θ_e$ and arbitrary $q$ and express the critical capillary number as a function of $θ_e$ and $r_m$. An analogy can be drawn between $r_m$ and the numerical slip length. △ Less

Submitted 27 October, 2018; v1 submitted 20 March, 2017; originally announced March 2017.

Comments: This version of the paper includes the corrections indicated in Ref. [1]

Journal ref: Journal of Computational Physics, Volume 374, Pages 1061-1093, 2018

Dispersion and viscous attenuation of capillary waves with finite amplitude

Authors: Fabian Denner, Gounséti Paré, Stéphane Zaleski

Abstract: We present a comprehensive study of the dispersion of capillary waves with finite amplitude, based on direct numerical simulations. The presented results show an increase of viscous attenuation and, consequently, a smaller frequency of capillary waves with increasing initial wave amplitude. Interestingly, however, the critical wavenumber as well as the wavenumber at which the maximum frequency is… ▽ More We present a comprehensive study of the dispersion of capillary waves with finite amplitude, based on direct numerical simulations. The presented results show an increase of viscous attenuation and, consequently, a smaller frequency of capillary waves with increasing initial wave amplitude. Interestingly, however, the critical wavenumber as well as the wavenumber at which the maximum frequency is observed remain the same for a given two-phase system, irrespective of the wave amplitude. By devising an empirical correlation that describes the effect of the wave amplitude on the viscous attenuation, the dispersion of capillary waves with finite initial amplitude is shown to be, in very good approximation, self-similar throughout the entire underdamped regime and independent of the fluid properties. The results also shown that analytical solutions for capillary waves with infinitesimal amplitude are applicable with reasonable accuracy for capillary waves with moderate amplitude. △ Less

Submitted 26 January, 2017; originally announced January 2017.

Comments: Accepted manuscript for publication in European Physical Journal Special Topics

Vortices catapult droplets in atomization

Authors: J John Soundar Jerome, Sylvain Marty, Jean-Philippe Matas, Stéphane Zaleski, Jérôme Hoepffner

Abstract: A droplet ejection mechanism in planar two-phase mixing layers is examined. Any disturbance on the gas-liquid interface grows into a Kelvin-Helmholtz wave, and the wave crest forms a thin liquid film that flaps as the wave grows downstream. Increasing the gas speed, it is observed that the film breaks up into droplets which are eventually thrown into the gas stream at large angles. In a flow where… ▽ More A droplet ejection mechanism in planar two-phase mixing layers is examined. Any disturbance on the gas-liquid interface grows into a Kelvin-Helmholtz wave, and the wave crest forms a thin liquid film that flaps as the wave grows downstream. Increasing the gas speed, it is observed that the film breaks up into droplets which are eventually thrown into the gas stream at large angles. In a flow where most of the momentum is in the horizontal direction, it is surprising to observe these large ejection angles. Our experiments and simulations show that a recirculation region grows downstream of the wave and leads to vortex shedding similar to the wake of a backward-facing step. The ejection mechanism results from the interaction between the liquid film and the vortex shedding sequence: a recirculation zone appears in the wake of the wave and a liquid film emerges from the wave crest; the recirculation region detaches into a vortex and the gas flow over the wave momentarily reattaches due to the departure of the vortex; this reattached flow pushes the liquid film down; by now, a new recirculation vortex is being created in the wake of the wave - just where the liquid film is now located; the liquid film is blown up from below by the newly formed recirculation vortex in a manner similar to a bag-breakup event; the resulting droplets are catapulted by the recirculation vortex. △ Less

Submitted 27 January, 2016; originally announced January 2016.

Comments: accepted for publication (2013)

Journal ref: Physics of Fluids 25, 112109 (2013)

Droplet impact on a thin liquid film: anatomy of the splash

Authors: Christophe Josserand, Pascal Ray, Stéphane Zaleski

Abstract: We investigate the dynamics of drop impact on a thin liquid film at short times in order to identify the mechanisms of splashing formation. Using numerical simulations and scaling analysis, we show that the splashing formation depends both on the inertial dynamics of the liquid and the cushioning of the gas. Two asymptotic regimes are identified, characterized by a new dimensionless number $J$: wh… ▽ More We investigate the dynamics of drop impact on a thin liquid film at short times in order to identify the mechanisms of splashing formation. Using numerical simulations and scaling analysis, we show that the splashing formation depends both on the inertial dynamics of the liquid and the cushioning of the gas. Two asymptotic regimes are identified, characterized by a new dimensionless number $J$: when the gas cushioning is weak, the jet is formed after a sequence of bubbles are entrapped and the jet speed is mostly selected by the Reynolds number of the impact. On the other hand, when the air cushioning is important, the lubrication of the gas beneath the drop and the liquid film controls the dynamics, leading to a single bubble entrapment and a weaker jet velocity. △ Less

Submitted 30 November, 2015; originally announced November 2015.

Spray formation: a numerical closeup

Authors: Yue Ling, Daniel Fuster, Gretar Tryggvason, Stephane Zaleski

Abstract: Spray formation and atomization in a gas-liquid mixing layer is an important fundamental problem of multiphase flows. It is highly desirable to visualize the detailed atomization process and to analyze the instabilities and mechanisms involved, and massive numerical simulations are required, in addition to experiment. Rapid development of numerical methods and computer technology in the past decad… ▽ More Spray formation and atomization in a gas-liquid mixing layer is an important fundamental problem of multiphase flows. It is highly desirable to visualize the detailed atomization process and to analyze the instabilities and mechanisms involved, and massive numerical simulations are required, in addition to experiment. Rapid development of numerical methods and computer technology in the past decades now allows large-scale three-dimensional direct numerical simulations of atomization to be performed. Nevertheless, the fundamental question, whether all the physical scales involved in the primary breakup process are faithfully resolved, remains unclear. In the present study, we conduct direct numerical simulations of spray formation in a gas-liquid mixing layer with state-of-the-art computational resources (using up to 4 billion cells and 16384 cores), in order to obtain a high-fidelity numerical closeup of the detailed mechanisms of spray formation. We also aim to examine whether present computational resources are sufficient for a fully resolved direct numerical simulation of atomization. △ Less

Submitted 11 July, 2016; v1 submitted 13 November, 2015; originally announced November 2015.

Journal ref: Phys. Rev. Fluids 2, 014005 (2017)

Scaling properties of viscous fingering

Authors: Bertrand Lagrée, Stéphane Zaleski, Igor Bondino, Christophe Josserand, Stéphane Popinet

Abstract: We present a study of viscous fingering using the Volume Of Fluid method and a central injection geometry, assuming a Laplacian field and a simple surface tension law. As in experiments we see branched structures resulting from the Saffman-Taylor instability. We find that the area $A$ of a viscous-fingering cluster varies as a simple power law $A \sim L^α$ of its interface length $L$. Our results… ▽ More We present a study of viscous fingering using the Volume Of Fluid method and a central injection geometry, assuming a Laplacian field and a simple surface tension law. As in experiments we see branched structures resulting from the Saffman-Taylor instability. We find that the area $A$ of a viscous-fingering cluster varies as a simple power law $A \sim L^α$ of its interface length $L$. Our results are compared to previously published simulations in which the viscosity of the invading fluid is vanishing. We find differences in exponent $α$ and in the appearance of detached droplets and bubbles. △ Less

Submitted 31 October, 2014; originally announced October 2014.

Von Kármán Vortex Street within an Impacting Drop

Authors: Marie-Jean Thoraval, Kohsei Takehara, Takeharu Goji Etoh, Stephane Popinet, Pascal Ray, Christophe Josserand, Stephane Zaleski, Sigurdur Thoroddsen

Abstract: The splashing of a drop impacting onto a liquid pool produces a range of different sized micro-droplets. At high impact velocities, the most significant source of these droplets is a thin liquid jet emerging at the start of the impact from the neck that connects the drop to the pool. We use ultra-high-speed video imaging in combination with high-resolution numerical simulations to show how the eje… ▽ More The splashing of a drop impacting onto a liquid pool produces a range of different sized micro-droplets. At high impact velocities, the most significant source of these droplets is a thin liquid jet emerging at the start of the impact from the neck that connects the drop to the pool. We use ultra-high-speed video imaging in combination with high-resolution numerical simulations to show how the ejecta gives way to irregular splashing. At higher Reynolds number, its base becomes unstable, shedding vortex rings into the liquid from the free surface in an axisymmetric von Kármán vortex street, thus breaking the ejecta sheet as it forms. △ Less

Submitted 29 February, 2012; originally announced February 2012.

Comments: 5 pages, 4 figure, 2 supplemental videos

Journal ref: Phys. Rev. Lett. 108, 264506 (2012)

Impact of a Viscous Liquid Drop

Authors: Robert D. Schroll, Christophe Josserand, Stéphane Zaleski, Wendy W. Zhang

Abstract: We simulate the impact of a viscous liquid drop onto a smooth dry solid surface. As in experiments, when ambient air effects are negligible, impact flattens the falling drop without producing a splash. The no-slip boundary condition at the wall produces a boundary layer inside the liquid. Later, the flattening surface of the drop traces out the boundary layer. As a result, the eventual shape of… ▽ More We simulate the impact of a viscous liquid drop onto a smooth dry solid surface. As in experiments, when ambient air effects are negligible, impact flattens the falling drop without producing a splash. The no-slip boundary condition at the wall produces a boundary layer inside the liquid. Later, the flattening surface of the drop traces out the boundary layer. As a result, the eventual shape of the drop is a "pancake" of uniform thickness except at the rim, where surface tension effects are significant. The thickness of the pancake is simply the height where the drop surface first collides with the boundary layer. △ Less

Submitted 2 April, 2009; originally announced April 2009.

Comments: 5 pages, 3 figures, submitted to Physical Review Letters