-
Drag Reduction in Flows Past 2D and 3D Circular Cylinders Through Deep Reinforcement Learning
Authors:
Michail Chatzimanolakis,
Pascal Weber,
Petros Koumoutsakos
Abstract:
We investigate drag reduction mechanisms in flows past two- and three-dimensional cylinders controlled by surface actuators using deep reinforcement learning. We investigate 2D and 3D flows at Reynolds numbers up to 8,000 and 4,000, respectively. The learning agents are trained in planar flows at various Reynolds numbers, with constraints on the available actuation energy. The discovered actuation…
▽ More
We investigate drag reduction mechanisms in flows past two- and three-dimensional cylinders controlled by surface actuators using deep reinforcement learning. We investigate 2D and 3D flows at Reynolds numbers up to 8,000 and 4,000, respectively. The learning agents are trained in planar flows at various Reynolds numbers, with constraints on the available actuation energy. The discovered actuation policies exhibit intriguing generalization capabilities, enabling open-loop control even for Reynolds numbers beyond their training range. Remarkably, the discovered two-dimensional controls, inducing delayed separation, are transferable to three-dimensional cylinder flows. We examine the trade-offs between drag reduction and energy input while discussing the associated mechanisms. The present work paves the way for control of unsteady separated flows via interpretable control strategies discovered through deep reinforcement learning.
△ Less
Submitted 5 September, 2023;
originally announced September 2023.
-
Ultraconfined plasmons in atomically thin crystalline silver nanostructures
Authors:
Vahagn Mkhitaryan,
Andrew P. Weber,
Saad Abdullah,
Laura Fernández,
Zakaria M. Abd El-Fattah,
Ignacio Piquero-Zulaica,
Hitesh Agarwal,
Kevin García Díez,
3 Frederik Schiller,
J. Enrique Ortega,
F. Javier García de Abajo
Abstract:
The ability to confine light down to atomic scales is critical for the development of applications in optoelectronics and optical sensing as well as for the exploration of nanoscale quantum phenomena. Plasmons in metallic nanostructures can achieve this type of confinement, although fabrication imperfections down to the subnanometer scale hinder actual developments. Here, we demonstrate narrow pla…
▽ More
The ability to confine light down to atomic scales is critical for the development of applications in optoelectronics and optical sensing as well as for the exploration of nanoscale quantum phenomena. Plasmons in metallic nanostructures can achieve this type of confinement, although fabrication imperfections down to the subnanometer scale hinder actual developments. Here, we demonstrate narrow plasmons in atomically thin crystalline silver nanostructures fabricated by prepatterning silicon substrates and epitaxially depositing silver films of just a few atomic layers in thickness. Combined with on-demand lateral sha**, this procedure allows for an unprecedented control over optical field confinement in the near-infrared spectral region. Specifically, we observe fundamental and higher-order plasmons featuring extreme spatial confinement and high-quality factors that reflect the crystallinity of the metal. Our approach holds potential for the design and exploitation of atomic-scale nanoplasmonic devices in optoelectronics, sensing, and quantum-physics applications.
△ Less
Submitted 20 March, 2023;
originally announced March 2023.
-
CubismAMR -- A C++ library for Distributed Block-Structured Adaptive Mesh Refinement
Authors:
Michail Chatzimanolakis,
Pascal Weber,
Fabian Wermelinger,
Petros Koumoutsakos
Abstract:
We present CubismAMR, a C++ library for distributed simulations with block-structured grids and Adaptive Mesh Refinement. A numerical method to solve the incompressible Navier-Stokes equations is proposed, that comes with a novel approach of solving the pressure Poisson equation on an adaptively refined grid. Validation and verification results for the method are presented, for the flow past an im…
▽ More
We present CubismAMR, a C++ library for distributed simulations with block-structured grids and Adaptive Mesh Refinement. A numerical method to solve the incompressible Navier-Stokes equations is proposed, that comes with a novel approach of solving the pressure Poisson equation on an adaptively refined grid. Validation and verification results for the method are presented, for the flow past an impulsively started cylinder.
△ Less
Submitted 20 June, 2022; v1 submitted 15 June, 2022;
originally announced June 2022.
-
Transverse Electron Beam Sha** with Light
Authors:
Marius Constantin Chirita Mihaila,
Philipp Weber,
Matthias Schneller,
Lucas Grandits,
Stefan Nimmrichter,
Thomas Juffmann
Abstract:
Interfacing electrons and light enables ultrafast electron microscopy, quantum control of electrons, as well as new optical elements for high sensitivity imaging. Here we demonstrate for the first time programmable transverse electron beam sha** in free space based on ponderomotive potentials from short intense laser pulses. We can realize both convex and concave electron lenses with a focal len…
▽ More
Interfacing electrons and light enables ultrafast electron microscopy, quantum control of electrons, as well as new optical elements for high sensitivity imaging. Here we demonstrate for the first time programmable transverse electron beam sha** in free space based on ponderomotive potentials from short intense laser pulses. We can realize both convex and concave electron lenses with a focal length of a few millimeters, comparable to those in state-of-the-art electron microscopes. We further show that we can realize almost arbitrary deflection patterns by sha** the ponderomotive potentials using a spatial light modulator. Our modulator is lossless, programmable, has unity fill factor, and could pave the way to electron wavefront sha** with hundreds of individually addressable pixels.
△ Less
Submitted 27 August, 2023; v1 submitted 15 March, 2022;
originally announced March 2022.
-
Statistical method for analysis of interactions between chosen protein and chondroitin sulfate in an aqueous environment
Authors:
Piotr Weber,
Piotr Bełdowski,
Adam Gadomski,
Krzysztof Domino,
Piotr Sionkowski,
Damian Ledziński
Abstract:
We present the statistical method to study the interaction between a chosen protein and another molecule (e.g., both being components of lubricin found in synovial fluid) in a water environment. The research is performed on the example of univariate time series of chosen features of the dynamics of mucin, which interact with chondroitin sulfate (4 and 6) in four different saline solutions. Our sta…
▽ More
We present the statistical method to study the interaction between a chosen protein and another molecule (e.g., both being components of lubricin found in synovial fluid) in a water environment. The research is performed on the example of univariate time series of chosen features of the dynamics of mucin, which interact with chondroitin sulfate (4 and 6) in four different saline solutions. Our statistical approach is based on recurrence methods to analyze chosen features of molecular dynamics. Such recurrence methods are usually applied to reconstruct the evolution of a molecular system in its reduced phase space, where the most important variables in the process are taken into account. In detail, the analyzed time-series are spitted onto sub-series of records that are expected to carry meaningful information about the system of molecules. Elements of sub-series are splinted by the constant delay-time lag (that is the parameter determined by statistical testing in our case), and the length of sub-series is the embedded dimension parameter (using the Cao method). We use the recurrent plots approach combined with the Shannon entropy approach to analyze the robustness of the sub-series determination. We hypothesize that the robustness of the sub-series determines some specifics of the dynamics of the system of molecules. We analyze rather highly noised features to demonstrate that such features lead to recurrence plots that graphically look similar. From the recurrence plots, the Shannon entropy has been computed. We have, however, demonstrated that the Shannon entropy value is highly dependent on the delay time value for analyzed features. Hence, elaboration of a more precise method of the recurrence plot analysis is required. For this reason, we suggest the random walk method that can be applied to analyze the recurrence plots automatically.
△ Less
Submitted 22 February, 2023; v1 submitted 13 January, 2022;
originally announced February 2022.
-
Learning swimming escape patterns for larval fish under energy constraints
Authors:
Ioannis Mandralis,
Pascal Weber,
Guido Novati,
Petros Koumoutsakos
Abstract:
Swimming organisms can escape their predators by creating and harnessing unsteady flow fields through their body motions. Stochastic optimization and flow simulations have identified escape patterns that are consistent with those observed in natural larval swimmers. However, these patterns have been limited by the specification of a particular cost function and depend on a prescribed functional fo…
▽ More
Swimming organisms can escape their predators by creating and harnessing unsteady flow fields through their body motions. Stochastic optimization and flow simulations have identified escape patterns that are consistent with those observed in natural larval swimmers. However, these patterns have been limited by the specification of a particular cost function and depend on a prescribed functional form of the body motion. Here, we deploy reinforcement learning to discover swimmer escape patterns for larval fish under energy constraints. The identified patterns include the C-start mechanism, in addition to more energetically efficient escapes. We find that maximizing distance with limited energy requires swimming via short bursts of accelerating motion interlinked with phases of gliding. The present, data efficient, reinforcement learning algorithm results in an array of patterns that reveal practical flow optimization principles for efficient swimming and the methodology can be transferred to the control of aquatic robotic devices operating under energy constraints.
△ Less
Submitted 28 June, 2021; v1 submitted 3 May, 2021;
originally announced May 2021.
-
Ultrafast X-Ray Scattering: New Views of Chemical Reaction Dynamics
Authors:
Peter M. Weber,
Brian Stankus,
Adam Kirrander
Abstract:
The advent of ultrafast pulsed X-ray free-electron lasers with very high brightness has enabled the determination of transient molecular structures of small and medium-sized organic molecules in excited states and undergoing chemical dynamics using X-ray scattering. This chapter provides an introduction into X-ray scattering theory and considers several important aspects relating to the experiment…
▽ More
The advent of ultrafast pulsed X-ray free-electron lasers with very high brightness has enabled the determination of transient molecular structures of small and medium-sized organic molecules in excited states and undergoing chemical dynamics using X-ray scattering. This chapter provides an introduction into X-ray scattering theory and considers several important aspects relating to the experimental implementation. Ultrafast gas phase X-ray scattering is shown to provide new observables to elucidate the dynamics of chemical reactions by providing complete, time-dependent molecular structures. Consideration of correlations between structural parameters are important for molecules far from their equilibrium and the changes in electron density distributions of molecules upon optical excitation need to be considered in the analysis. Future technological developments are expected to lead to further important advances.
△ Less
Submitted 5 March, 2020;
originally announced March 2020.
-
To beer or not to beer: does tap** beer cans prevent beer loss? A randomised controlled trial
Authors:
Elizaveta Sopina,
Irina E. Antonescu,
Thomas Hansen,
Torben Hoejland,
Morten M. Jensen,
Simon V. Pedersen,
Wade Thompson,
Philipp Weber,
Jamie O Halloran,
Melissa G. Beach,
Ryan Pulleyblank,
Elliot J. Brown
Abstract:
Objective: Preventing or minimising beer loss when opening a can of beer is socially and economically desirable. One theoretically grounded approach is tap** the can prior to opening, although this has never been rigorously evaluated. We aimed to evaluate the effect of tap** a can of beer on beer loss. Methods: Single centre parallel-group randomised controlled trial. 1031 cans of cans of beer…
▽ More
Objective: Preventing or minimising beer loss when opening a can of beer is socially and economically desirable. One theoretically grounded approach is tap** the can prior to opening, although this has never been rigorously evaluated. We aimed to evaluate the effect of tap** a can of beer on beer loss. Methods: Single centre parallel-group randomised controlled trial. 1031 cans of cans of beer of 330mL were randomised into one of four groups before the experiment: unshaken/untapped (n=256), unshaken/tapped (n=251), shaken/untapped (n=249), or shaken/tapped (n=244). The intervention was tap** the can of beer three times on its side with a single finger. We compared tap** versus non-tap** for cans that had been shaken for 2 minutes or were unshaken. Three teams weighed, tapped or did not tap, opened cans, absorbed any beer loss using paper towels, then re-weighed cans. The teams recorded the mass of each can before and after opening with an accuracy of +/-0.01 grams. Main outcome measure: The main outcome measure was beer loss (in grams). This was calculated as the difference in the mass of the beer after the can was opened compared to before the can was opened. Results: For shaken cans, there was no statistically significant difference in the mass of beer lost when tap** compared to not tap** (mean difference of -0.159g beer lost with tap**, 95% CI -0.36 to 0.04). For unshaken cans, there was also no statistically significant difference between tap** and not tap**. Conclusion: These findings suggest that tap** shaken beer cans does not prevent beer loss when the container is opened. Thus, the practice of tap** a beer prior to opening is unsupported. The only apparent remedy to avoid liquid loss is to wait for bubbles to settle before opening the can.
△ Less
Submitted 9 December, 2019; v1 submitted 3 December, 2019;
originally announced December 2019.
-
Optimal sensing for fish school identification
Authors:
Pascal Weber,
Georgios Arampatzis,
Guido Novati,
Siddhartha Verma,
Costas Papadimitriou,
Petros Koumoutsakos
Abstract:
Fish schooling implies an awareness of the swimmers for their companions. In flow mediated environments, in addition to visual cues, pressure and shear sensors on the fish body are critical for providing quantitative information that assists the quantification of proximity to other swimmers. Here we examine the distribution of sensors on the surface of an artificial swimmer so that it can optimall…
▽ More
Fish schooling implies an awareness of the swimmers for their companions. In flow mediated environments, in addition to visual cues, pressure and shear sensors on the fish body are critical for providing quantitative information that assists the quantification of proximity to other swimmers. Here we examine the distribution of sensors on the surface of an artificial swimmer so that it can optimally identify a leading group of swimmers. We employ Bayesian experimental design coupled with two-dimensional Navier Stokes equations for multiple self-propelled swimmers. The follower tracks the school using information from its own surface pressure and shear stress. We demonstrate that the optimal sensor distribution of the follower is qualitatively similar to the distribution of neuromasts on fish. Our results show that it is possible to identify accurately the center of mass and even the number of the leading swimmers using surface only information.
△ Less
Submitted 22 October, 2019;
originally announced October 2019.
-
Imaging the Photochemical Ring-Opening of 1,3-Cyclohexadiene by Ultrafast Electron Diffraction
Authors:
T. J. A. Wolf,
D. M. Sanchez,
J. Yang,
R. M. Parrish,
J. P. F. Nunes,
M. Centurion,
R. Coffee,
J. P. Cryan,
M. Gühr,
K. Hegazy,
A. Kirrander,
R. K. Li,
J. Ruddock,
X. Shen,
T. Veccione,
S. P. Weathersby,
P. M. Weber,
K. Wilkin,
H. Yong,
Q. Zheng,
X. J. Wang,
M. P. Minitti,
T. J. Martínez
Abstract:
The ultrafast photoinduced ring-opening of 1,3-cyclohexadiene constitutes a textbook example of electrocyclic reactions in organic chemistry and a model for photobiological reactions in vitamin D synthesis. Here, we present direct and unambiguous observation of the ring-opening reaction path on the femtosecond timescale and sub-Ångström length scale by megaelectronvolt ultrafast electron diffracti…
▽ More
The ultrafast photoinduced ring-opening of 1,3-cyclohexadiene constitutes a textbook example of electrocyclic reactions in organic chemistry and a model for photobiological reactions in vitamin D synthesis. Here, we present direct and unambiguous observation of the ring-opening reaction path on the femtosecond timescale and sub-Ångström length scale by megaelectronvolt ultrafast electron diffraction. We follow the carbon-carbon bond dissociation and the structural opening of the 1,3-cyclohexadiene ring by direct measurement of time-dependent changes in the distribution of interatomic distances. We observe a substantial acceleration of the ring-opening motion after internal conversion to the ground state due to steepening of the electronic potential gradient towards the product minima. The ring-opening motion transforms into rotation of the terminal ethylene groups in the photoproduct 1,3,5-hexatriene on the sub-picosecond timescale. Our work demonstrates the potential of megaelectronvolt ultrafast electron diffraction to elucidate photochemical reaction paths in organic chemistry.
△ Less
Submitted 5 October, 2018;
originally announced October 2018.
-
High quality factor graphene-based 2D heterostructure mechanical resonator
Authors:
M. Will,
M. Hamer,
M. Müller,
A. Noury,
P. Weber,
A. Bachtold,
R. V. Gorbachev,
C. Stampfer,
J. Güttinger
Abstract:
Ultralight mechanical resonators based on low-dimensional materials are well suited as exceptional transducers of minuscule forces or mass changes. However, the low dimensionality also provides a challenge to minimize resistive losses and heating. Here, we report on a novel approach that aims to combine different 2D materials to tackle this challenge. We fabricated a heterostructure mechanical res…
▽ More
Ultralight mechanical resonators based on low-dimensional materials are well suited as exceptional transducers of minuscule forces or mass changes. However, the low dimensionality also provides a challenge to minimize resistive losses and heating. Here, we report on a novel approach that aims to combine different 2D materials to tackle this challenge. We fabricated a heterostructure mechanical resonator consisting of few layers of niobium diselenide (NbSe$_2$) encapsulated by two graphene sheets. The hybrid membrane shows high quality factors up to 245'000 at low temperatures, comparable to the best few-layer graphene mechanical resonators. In contrast to few-layer graphene resonators, the device shows reduced electrical losses attributed to the lower resistivity of the NbSe$_2$ layer. The peculiar low temperature dependence of the intrinsic quality factor points to dissipation over two-level systems which in turn relax over the electronic system. Our high sensitivity readout is enabled by coupling the membrane to a superconducting cavity which allows for the integration of the hybrid mechanical resonator as a sensitive and low loss transducer in future quantum circuits.
△ Less
Submitted 17 September, 2018;
originally announced September 2018.
-
Linac activation of radioisotopes and underground gammaspectrometric analyses
Authors:
Patrick Weber,
Jean-Luc Vuilleumier,
Geoffroy Guibert,
Claire Tamburella
Abstract:
After irradiating various medical linac parts with photon beams, we performed underground gamma-ray spectroscopy (GRS) measurements of the samples only a few minutes after the irradiations, in order to observe activated short-lived radioisotopes. Three samples were used: an Elekta Synergy flattening filter never irradiated before, an old flattening filter, unmounted from a linac in 2012 and a tung…
▽ More
After irradiating various medical linac parts with photon beams, we performed underground gamma-ray spectroscopy (GRS) measurements of the samples only a few minutes after the irradiations, in order to observe activated short-lived radioisotopes. Three samples were used: an Elekta Synergy flattening filter never irradiated before, an old flattening filter, unmounted from a linac in 2012 and a tungsten leaf, unmounted from the multileaf collimator (MLC) of the same linac in 2012. All three samples were measured before the irradiations in the underground laboratory of la Vue-des-Alpes.
The new flattening filter and the leaf were then irradiated with ~200 Gy, first under 15MV and then with 6MV photon beams. The gamma counting began 20 minutes after the irradiations. Irradiations with 15MV led to (n,γ) activation of short-lived isotopes : In the leaf, the measured activity was 1556 Bq just after the irradiation and we observed various gamma lines from 187W, 57Ni and 56Mn. In the new filter, the activity was 1097 Bq and the gamma signature of 56Mn, 56Ni, 57Ni and 59Co was clearly present. The germanium detector allowed to measure gamma lines with relative intensities (branching ratio BR) down to ~0.1%, thank to its very low background. Irradiations of the new flattening filter at 6MV led to a small activation of 56Mn. Gammaspectroscopic data was taken several times after the irradiation to monitor the time evolution and the total activity. Treating patients with 15MV photon beams activate long-lived radioisotopes in the linac head. With this work, it was possible to identify these isotopes, and especially highlight the created short-lived radioisotopes.
△ Less
Submitted 28 May, 2018;
originally announced May 2018.
-
A volumetric Modulated Arc Therapy (VMAT) combined with deep inspiration breath hold (DIBH) technique for adjuvant irradiation for left sided breast cancer
Authors:
C. Tamburella,
G. Guibert,
O. Santa Cruz,
P. Weber,
P. Tsousou
Abstract:
Background: The deep inspiration breath hold technique (DIBH) is widely used for left-sided breast radiotherapy (RT), in order to reduce the dose to the heart and the risk of cardiotoxicity. The volumetric arc therapy (VMAT) technique increases the dose conformity to the planning target volume (PTV). We hereby describe the procedure of combining VMAT and DIBH without a dedicated equipment, and rep…
▽ More
Background: The deep inspiration breath hold technique (DIBH) is widely used for left-sided breast radiotherapy (RT), in order to reduce the dose to the heart and the risk of cardiotoxicity. The volumetric arc therapy (VMAT) technique increases the dose conformity to the planning target volume (PTV). We hereby describe the procedure of combining VMAT and DIBH without a dedicated equipment, and report a dosimetric study related on our implemented technique. Methods: The DIBH technique is based on voluntary breath hold of the patient which is controlled by a laser on tattoo marks. Patients were selected depending their ability to breath hold for 25s, and VMAT plans were optimized with an arrangement of 4 arcs with a maximum delivery time of 20s each. A retrospective dosimetric study was undertaken on 30 patients treated with this technique: 10 received local (whole breast) RT (L-RT) with a simultaneous integrated boost (SIB), 10 a locoregional (LR)RT of the chestwall, 10 a LR RT of the whole breast with SIB. For these patients, their DIBH-VMAT treatment plans were compared to free breathing (FB) VMAT plans, and dose characteristics of PTV and organs at risk (OAR) were evaluated. Results: The PTV coverage was identical among plans under DIBH or FB. The mean heart dose was reduced from 2.8+/-0.9Gy in FB to 1.8+/-0.6Gy in DIBH for local RT, and reduced from 3.4+/-1.3Gy in FB to 2.2+/-0.5Gy in DIBH for LR-RT. The ipsilateral mean lung dose was reduced by a factor of 12% for LR-RT, but remained unchanged for L-RT with DIBH-VMAT compared to FB treatment. No significant differences were observed in the mean dose of contra-lateral organs with either DIBH or FB VMAT techniques. Conclusion: The VMAT-DIBH technique performed without a dedicated breath hold equipment, provided important dose reductions at the heart, while preserving the ipsilateral lung and contralateral normal tissues.
△ Less
Submitted 13 March, 2019; v1 submitted 21 June, 2017;
originally announced June 2017.
-
Observation of a two-dimensional electron gas at CaTiO$_3$ film surfaces
Authors:
Stefan Muff,
Mauro Fanciulli,
Andrew P. Weber,
Nicolas Pilet,
Zoran Ristic,
Zhiming Wang,
Nicholas C. Plumb,
Milan Radovic,
J. Hugo Dil
Abstract:
The two-dimensional electron gas at the surface of titanates gathered attention due to its potential to replace conventional silicon based semiconductors in the future. In this study, we investigated films of the parent perovskite CaTiO$_3$, grown by pulsed laser deposition, by means of angular-resolved photoelectron spectroscopy. The films show a c(4x2) surface reconstruction after the growth tha…
▽ More
The two-dimensional electron gas at the surface of titanates gathered attention due to its potential to replace conventional silicon based semiconductors in the future. In this study, we investigated films of the parent perovskite CaTiO$_3$, grown by pulsed laser deposition, by means of angular-resolved photoelectron spectroscopy. The films show a c(4x2) surface reconstruction after the growth that is reduced to a p(2x2) reconstruction under UV-light. At the CaTiO$_3$ film surface, a two-dimensional electron gas (2DEG) is found with an occupied band width of 400 meV. With our findings CaTiO$_3$ is added to the group of oxides with a 2DEG at their surface. Our study widens the phase space to investigate strontium and barium doped CaTiO$_3$ and the interplay of ferroelectric properties with the 2DEG at oxide surfaces. This could open up new paths to tailor two-dimensional transport properties of these systems towards possible applications.
△ Less
Submitted 26 May, 2017;
originally announced May 2017.
-
Designs for a Quantum Electron Microscope
Authors:
Pieter Kruit,
Richard G. Hobbs,
Chung-Soo Kim,
Yujia Yang,
Vitor R. Manfrinato,
Jacob Hammer,
Sebastian Thomas,
Philipp Weber,
Brannon Klopfer,
Christoph Kohstall,
Thomas Juffmann,
Mark A. Kasevich,
Peter Hommelhoff,
Karl K. Berggren
Abstract:
One of the astounding consequences of quantum mechanics is that it allows the detection of a target using an incident probe, with only a low probability of interaction of the probe and the target. This 'quantum weirdness' could be applied in the field of electron microscopy to generate images of beam-sensitive specimens with substantially reduced damage to the specimen. A reduction of beam-induced…
▽ More
One of the astounding consequences of quantum mechanics is that it allows the detection of a target using an incident probe, with only a low probability of interaction of the probe and the target. This 'quantum weirdness' could be applied in the field of electron microscopy to generate images of beam-sensitive specimens with substantially reduced damage to the specimen. A reduction of beam-induced damage to specimens is especially of great importance if it can enable imaging of biological specimens with atomic resolution. Following a recent suggestion that interaction-free measurements are possible with electrons, we now analyze the difficulties of actually building an atomic resolution interaction-free electron microscope, or "quantum electron microscope". A quantum electron microscope would require a number of unique components not found in conventional transmission electron microscopes. These components include a coherent electron-beam splitter or two-state-coupler, and a resonator structure to allow each electron to interrogate the specimen multiple times, thus supporting high success probabilities for interaction-free detection of the specimen. Different system designs are presented here, which are based on four different choices of two-state-couplers: a thin crystal, a grating mirror, a standing light wave and an electro-dynamical pseudopotential. Challenges for the detailed electron optical design are identified as future directions for development. While it is concluded that it should be possible to build an atomic resolution quantum electron microscope, we have also identified a number of hurdles to the development of such a microscope and further theoretical investigations that will be required to enable a complete interpretation of the images produced by such a microscope.
△ Less
Submitted 20 October, 2015;
originally announced October 2015.
-
A microwave chip-based beam splitter for low-energy guided electrons
Authors:
Jakob Hammer,
Sebastian Thomas,
Philipp Weber,
Peter Hommelhoff
Abstract:
We demonstrate the splitting of a low-energy electron beam by means of a microwave pseudopotential formed above a planar chip substrate. Beam splitting arises from smoothly transforming the transverse guiding potential for an electron beam from a single-well harmonic confinement into a double-well, thereby generating two separated output beams with $5\,$mm lateral spacing. Efficient beam splitting…
▽ More
We demonstrate the splitting of a low-energy electron beam by means of a microwave pseudopotential formed above a planar chip substrate. Beam splitting arises from smoothly transforming the transverse guiding potential for an electron beam from a single-well harmonic confinement into a double-well, thereby generating two separated output beams with $5\,$mm lateral spacing. Efficient beam splitting is observed for electron kinetic energies up to $3\,$eV, in excellent agreement with particle tracking simulations. We discuss prospects of this novel beam splitter approach for electron-based quantum matter-wave optics experiments.
△ Less
Submitted 18 May, 2015; v1 submitted 12 August, 2014;
originally announced August 2014.
-
Systematic study of trace radioactive impurities in candidate construction materials for EXO-200
Authors:
D. S. Leonard,
P. Grinberg,
P. Weber,
E. Baussan,
Z. Djurcic,
G. Keefer,
A. Piepke,
A. Pocar,
J. -L. Vuilleumier,
J. -M. Vuilleumier,
D. Akimov,
A. Bellerive,
M. Bowcock,
M. Breidenbach,
A. Burenkov,
R. Conley,
W. Craddock,
M. Danilov,
R. DeVoe,
M. Dixit,
A. Dolgolenko,
I. Ekchtout,
W. Fairbank Jr.,
J. Farine,
P. Fierlinger
, et al. (32 additional authors not shown)
Abstract:
The Enriched Xenon Observatory (EXO) will search for double beta decays of 136Xe. We report the results of a systematic study of trace concentrations of radioactive impurities in a wide range of raw materials and finished parts considered for use in the construction of EXO-200, the first stage of the EXO experimental program. Analysis techniques employed, and described here, include direct gamma…
▽ More
The Enriched Xenon Observatory (EXO) will search for double beta decays of 136Xe. We report the results of a systematic study of trace concentrations of radioactive impurities in a wide range of raw materials and finished parts considered for use in the construction of EXO-200, the first stage of the EXO experimental program. Analysis techniques employed, and described here, include direct gamma counting, alpha counting, neutron activation analysis, and high-sensitivity mass spectrometry.
△ Less
Submitted 4 August, 2008; v1 submitted 28 September, 2007;
originally announced September 2007.
-
SILEM : a new gaseous detector with integrated x-y readout plane
Authors:
Patrick Weber
Abstract:
This works reports on gaseous detectors developments made in the frame of the EXO double-beta decay experiment. LEM (Large Electron Multiplication) are electron amplification grids based on GEM. They were developed in Neuchatel and showed remarquable resistance to sparks. The new SILEM grid combines the properties of the standard LEM with a micropatterned x-y readout plane on one of the grid sid…
▽ More
This works reports on gaseous detectors developments made in the frame of the EXO double-beta decay experiment. LEM (Large Electron Multiplication) are electron amplification grids based on GEM. They were developed in Neuchatel and showed remarquable resistance to sparks. The new SILEM grid combines the properties of the standard LEM with a micropatterned x-y readout plane on one of the grid side. It allows thus the amplification of the primary electrons and their position determination in the x-y plane.
△ Less
Submitted 11 June, 2007;
originally announced June 2007.
-
A linear RFQ ion trap for the Enriched Xenon Observatory
Authors:
B. Flatt,
M. Green,
J. Wodin,
R. DeVoe,
P. Fierlinger,
G. Gratta,
F. LePort,
M. Montero Diez,
R. Neilson,
K. OSullivan,
A. Pocar,
S. Waldman,
E. Baussan,
M. Breidenbach,
R. Conley,
W. Fairbank Jr.,
J. Farine,
C. Hall,
K. Hall,
D. Hallman,
C. Hargrove,
M. Hauger,
J. Hodgson,
F. Juget,
D. S. Leonard
, et al. (17 additional authors not shown)
Abstract:
The design, construction, and performance of a linear radio-frequency ion trap (RFQ) intended for use in the Enriched Xenon Observatory (EXO) are described. EXO aims to detect the neutrinoless double-beta decay of $^{136}$Xe to $^{136}$Ba. To suppress possible backgrounds EXO will complement the measurement of decay energy and, to some extent, topology of candidate events in a Xe filled detector…
▽ More
The design, construction, and performance of a linear radio-frequency ion trap (RFQ) intended for use in the Enriched Xenon Observatory (EXO) are described. EXO aims to detect the neutrinoless double-beta decay of $^{136}$Xe to $^{136}$Ba. To suppress possible backgrounds EXO will complement the measurement of decay energy and, to some extent, topology of candidate events in a Xe filled detector with the identification of the daughter nucleus ($^{136}$Ba). The ion trap described here is capable of accepting, cooling, and confining individual Ba ions extracted from the site of the candidate double-beta decay event. A single trapped ion can then be identified, with a large signal-to-noise ratio, via laser spectroscopy.
△ Less
Submitted 12 April, 2007;
originally announced April 2007.
-
Observation of single collisionally cooled trapped ions in a buffer gas
Authors:
M. Green,
J. Wodin,
R. DeVoe,
P. Fierlinger,
B. Flatt,
G. Gratta,
F. LePort,
M. Montero Diez,
R. Neilson,
K. OSullivan,
A. Pocar,
S. Waldman,
D. S. Leonard,
A. Piepke,
C. Hargrove,
D. Sinclair,
V. Strickland,
W. Fairbank Jr.,
K. Hall,
B. Mong,
M. Moe,
J. Farine,
D. Hallman,
C. Virtue,
E. Baussan
, et al. (15 additional authors not shown)
Abstract:
Individual Ba ions are trapped in a gas-filled linear ion trap and observed with a high signal-to-noise ratio by resonance fluorescence. Single-ion storage times of ~5 min (~1 min) are achieved using He (Ar) as a buffer gas at pressures in the range 8e-5 - 4e-3 torr. Trap dynamics in buffer gases are experimentally studied in the simple case of single ions. In particular, the cooling effects of…
▽ More
Individual Ba ions are trapped in a gas-filled linear ion trap and observed with a high signal-to-noise ratio by resonance fluorescence. Single-ion storage times of ~5 min (~1 min) are achieved using He (Ar) as a buffer gas at pressures in the range 8e-5 - 4e-3 torr. Trap dynamics in buffer gases are experimentally studied in the simple case of single ions. In particular, the cooling effects of light gases such as He and Ar and the destabilizing properties of heavier gases such as Xe are studied. A simple model is offered to explain the observed phenomenology.
△ Less
Submitted 5 July, 2007; v1 submitted 14 February, 2007;
originally announced February 2007.
-
A liquid xenon ionization chamber in an all-fluoropolymer vessel
Authors:
EXO Collaboration,
F. LePort,
A. Pocar,
L. Bartoszek,
R. DeVoe,
P. Fierlinger,
B. Flatt,
G. Gratta,
M. Green,
T. Koffas,
M. Montero Diez,
R. Neilson,
K. O'Sullivan,
S. Waldman,
J. Wodin,
D. Woisard,
E. Baussan,
M. Breidenbach,
R. Conley,
W. Fairbank Jr.,
J. Farine,
C. Hall,
K. Hall,
D. Hallman,
C. Hargrove
, et al. (20 additional authors not shown)
Abstract:
A novel technique has been developed to build vessels for liquid xenon ionization detectors entirely out of ultra-clean fluoropolymer. We describe the advantages in terms of low radioactivity contamination, provide some details of the construction techniques, and show the energy resolution achieved with a prototype all-fluoropolymer ionization detector.
A novel technique has been developed to build vessels for liquid xenon ionization detectors entirely out of ultra-clean fluoropolymer. We describe the advantages in terms of low radioactivity contamination, provide some details of the construction techniques, and show the energy resolution achieved with a prototype all-fluoropolymer ionization detector.
△ Less
Submitted 19 November, 2006;
originally announced November 2006.
-
Are volatility correlations in financial markets related to Omori processes occurring on all scales?
Authors:
Philipp Weber,
Fengzhong Wang,
Irena Vodenska-Chitkushev,
Shlomo Havlin,
H. Eugene Stanley
Abstract:
We analyze the memory in volatility by studying volatility return intervals, defined as the time between two consecutive fluctuations larger than a given threshold, in time periods following stock market crashes. Such an aftercrash period is characterized by the Omori law, which describes the decay in the rate of aftershocks of a given size with time t by a power law with exponent close to 1. A…
▽ More
We analyze the memory in volatility by studying volatility return intervals, defined as the time between two consecutive fluctuations larger than a given threshold, in time periods following stock market crashes. Such an aftercrash period is characterized by the Omori law, which describes the decay in the rate of aftershocks of a given size with time t by a power law with exponent close to 1. A shock followed by such a power law decay in the rate is here called Omori process. Studying several aftercrash time series, we show that the Omori law holds not only after significant market crashes, but also after ``intermediate shocks''. Moreover, we find self-similar features in the volatility. Specifically, within the aftercrash period there are smaller shocks that themselves constitute Omori processes on smaller scales, similar to the Omori process after the large crash. We call these smaller shocks subcrashes, which are followed by their own aftershocks. We also find similar Omori processes after intermediate crashes in time regimes without a large market crash. By appropriate detrending we remove the influence of the crashes and subcrashes from the data, and find that this procedure significantly reduces the memory in the records. Our results are consistent with the hypothesis that the memory in volatility is related to Omori processes present on different time scales.
△ Less
Submitted 9 November, 2006;
originally announced November 2006.
-
Analysis of aggregated tick returns: evidence for anomalous diffusion
Authors:
Philipp Weber
Abstract:
In order to investigate the origin of large price fluctuations, we analyze stock price changes of ten frequently traded NASDAQ stocks in the year 2002. Though the influence of the trading frequency on the aggregate return in a certain time interval is important, it cannot alone explain the heavy tailed distribution of stock price changes. For this reason, we analyze intervals with a fixed number…
▽ More
In order to investigate the origin of large price fluctuations, we analyze stock price changes of ten frequently traded NASDAQ stocks in the year 2002. Though the influence of the trading frequency on the aggregate return in a certain time interval is important, it cannot alone explain the heavy tailed distribution of stock price changes. For this reason, we analyze intervals with a fixed number of trades in order to eliminate the influence of the trading frequency and investigate the relevance of other factors for the aggregate return. We show that in tick time the price follows a discrete diffusion process with a variable step width while the difference between the number of steps in positive and negative direction in an interval is Gaussian distributed. The step width is given by the return due to a single trade and is long-term correlated in tick time. Hence, its mean value can well characterize an interval of many trades and turns out to be an important determinant for large aggregate returns. We also present a statistical model reproducing the cumulative distribution of aggregate returns. For an accurate agreement with the empirical distribution, we also take into account asymmetries of the step widths in different directions together with crosscorrelations between these asymmetries and the mean step width as well as the signs of the steps.
△ Less
Submitted 20 June, 2006; v1 submitted 18 June, 2006;
originally announced June 2006.