-
STOPGAP -- a Time-of-Flight Extension for the Belle II TOP Barrel PID System as a Demonstrator for CMOS Fast Timing Sensors
Authors:
Oskar Hartbrich,
Umberto Tamponi,
Gary S. Varner
Abstract:
The Belle II barrel region is instrumented with the Time of Propagation (TOP) particle identification system based on sixteen fused-silica bars arranged around the interaction point acting as Cherenkov radiator. Due to the mechanical design of the TOP system these quartz bars do not overlap, but leave a gap of around 2cm between them. This leads to around 6% of all tracks in the nominal TOP accept…
▽ More
The Belle II barrel region is instrumented with the Time of Propagation (TOP) particle identification system based on sixteen fused-silica bars arranged around the interaction point acting as Cherenkov radiator. Due to the mechanical design of the TOP system these quartz bars do not overlap, but leave a gap of around 2cm between them. This leads to around 6% of all tracks in the nominal TOP acceptance region to escape without traversing any of the quartz bars and thus not giving any usable particle identification information from the TOP system and an additional 3% of tracks being degraded due to edge effects. We propose a possible solution to remedy these gaps in the TOP acceptance in the form of a Supplemental TOP GAP instrumentation (STOPGAP) that covers the dead area between adjacent quartz bars with fast silicon detectors to directly measure the time-of-flight of traversing particles for particle identification purposes. Modern, fast timing silicon sensors and readouts can offer sufficient time resolution for the task at hand, so that STOPGAP modules could be built compact enough to fit into the limited space available in the area of interest between the Belle II central drift chamber (CDC) and the TOP system.
In this article, we present a simulation study demonstrating the feasibility of a silicon time-of-flight system based on its reconstruction performance in $Υ(4S)\rightarrow B\bar{B}$ events simulated using the Belle II simulation and reconstruction software. We discuss the performance requirements for possible sensor technologies and demonstrate that such a project could be realised with novel, fast monolithic CMOS sensors that are expected to reach MIP timing resolutions of down to 50ps. Additionally, we discuss the use of fast timing layers at lower radii for track triggering as well as particle identification at low momenta <1GeV/c.
△ Less
Submitted 9 March, 2022;
originally announced March 2022.
-
The TOP counter of Belle II: status and first results
Authors:
Umberto Tamponi
Abstract:
High-efficiency and high-purity particle identification are fundamental requirements for the success of the Belle II experiment, whose main goal is to explore the new-physics scenarios in the CP-violating decays of the B mesons. To achieve the required particle identification performances, the Time-of-propagation counter has been installed in the central barrel region. This unique device consists…
▽ More
High-efficiency and high-purity particle identification are fundamental requirements for the success of the Belle II experiment, whose main goal is to explore the new-physics scenarios in the CP-violating decays of the B mesons. To achieve the required particle identification performances, the Time-of-propagation counter has been installed in the central barrel region. This unique device consists in 16 bars of fused silica that act simultaneously as radiator and as light guide for the Cerenkov light. Unlike in the DIRC detectors, the PID information is mostly extracted measuring the time of propagation of the Cherenkov light in the radiator rather than its purely geometrical patterns. We will present here a general overview of the status of the TOP counter, including the estimation of the time resolution, the calibration strategies and performances, and the first result obtained in the commissioning phase, both using cosmic rays and $e^+e^-$ collision events collected during the {\it phase II} pilot run of the Belle II experiment. These are the first measurements of the particle identification performances of a time-of-propagation detector in a full HEP experimental setup.
△ Less
Submitted 11 November, 2018;
originally announced November 2018.
-
A Roadmap for HEP Software and Computing R&D for the 2020s
Authors:
Johannes Albrecht,
Antonio Augusto Alves Jr,
Guilherme Amadio,
Giuseppe Andronico,
Nguyen Anh-Ky,
Laurent Aphecetche,
John Apostolakis,
Makoto Asai,
Luca Atzori,
Marian Babik,
Giuseppe Bagliesi,
Marilena Bandieramonte,
Sunanda Banerjee,
Martin Barisits,
Lothar A. T. Bauerdick,
Stefano Belforte,
Douglas Benjamin,
Catrin Bernius,
Wahid Bhimji,
Riccardo Maria Bianchi,
Ian Bird,
Catherine Biscarat,
Jakob Blomer,
Kenneth Bloom,
Tommaso Boccali
, et al. (285 additional authors not shown)
Abstract:
Particle physics has an ambitious and broad experimental programme for the coming decades. This programme requires large investments in detector hardware, either to build new facilities and experiments, or to upgrade existing ones. Similarly, it requires commensurate investment in the R&D of software to acquire, manage, process, and analyse the shear amounts of data to be recorded. In planning for…
▽ More
Particle physics has an ambitious and broad experimental programme for the coming decades. This programme requires large investments in detector hardware, either to build new facilities and experiments, or to upgrade existing ones. Similarly, it requires commensurate investment in the R&D of software to acquire, manage, process, and analyse the shear amounts of data to be recorded. In planning for the HL-LHC in particular, it is critical that all of the collaborating stakeholders agree on the software goals and priorities, and that the efforts complement each other. In this spirit, this white paper describes the R&D activities required to prepare for this software upgrade.
△ Less
Submitted 19 December, 2018; v1 submitted 18 December, 2017;
originally announced December 2017.
