-
Solid State Detectors and Tracking for Snowmass
Authors:
A. Affolder,
A. Apresyan,
S. Worm,
M. Albrow,
D. Ally,
D. Ambrose,
E. Anderssen,
N. Apadula,
P. Asenov,
W. Armstrong,
M. Artuso,
A. Barbier,
P. Barletta,
L. Bauerdick,
D. Berry,
M. Bomben,
M. Boscardin,
J. Brau,
W. Brooks,
M. Breidenbach,
J. Buckley,
V. Cairo,
R. Caputo,
L. Carpenter,
M. Centis-Vignali
, et al. (110 additional authors not shown)
Abstract:
Tracking detectors are of vital importance for collider-based high energy physics (HEP) experiments. The primary purpose of tracking detectors is the precise reconstruction of charged particle trajectories and the reconstruction of secondary vertices. The performance requirements from the community posed by the future collider experiments require an evolution of tracking systems, necessitating the…
▽ More
Tracking detectors are of vital importance for collider-based high energy physics (HEP) experiments. The primary purpose of tracking detectors is the precise reconstruction of charged particle trajectories and the reconstruction of secondary vertices. The performance requirements from the community posed by the future collider experiments require an evolution of tracking systems, necessitating the development of new techniques, materials and technologies in order to fully exploit their physics potential. In this article we summarize the discussions and conclusions of the 2022 Snowmass Instrumentation Frontier subgroup on Solid State and Tracking Detectors (Snowmass IF03).
△ Less
Submitted 19 October, 2022; v1 submitted 8 September, 2022;
originally announced September 2022.
-
Monolithic Active Pixel Sensors on CMOS technologies
Authors:
Nicole Apadula,
Whitney Armstrong,
James Brau,
Martin Breidenbach,
R. Caputo,
Gabriella Carinii,
Alberto Collu,
Marcel Demarteau,
Grzegorz Deptuch,
Angelo Dragone,
Gabriele Giacomini,
Carl Grace,
Norman Graf,
Leo Greiner,
Ryan Herbst,
Gunther Haller,
Manoj Jadhav,
Sylvester Joosten,
Christopher J. Kenney,
C. Kierans,
Jihee Kim,
Thomas Markiewicz,
Yuan Mei,
Jessica Metcalfe,
Zein-Eddine Meziani
, et al. (15 additional authors not shown)
Abstract:
Collider detectors have taken advantage of the resolution and accuracy of silicon detectors for at least four decades. Future colliders will need large areas of silicon sensors for low mass trackers and sampling calorimetry. Monolithic Active Pixel Sensors (MAPS), in which Si diodes and readout circuitry are combined in the same pixels, and can be fabricated in some of standard CMOS processes, are…
▽ More
Collider detectors have taken advantage of the resolution and accuracy of silicon detectors for at least four decades. Future colliders will need large areas of silicon sensors for low mass trackers and sampling calorimetry. Monolithic Active Pixel Sensors (MAPS), in which Si diodes and readout circuitry are combined in the same pixels, and can be fabricated in some of standard CMOS processes, are a promising technology for high-granularity and light detectors. In this paper we review 1) the requirements on MAPS for trackers and electromagnetic calorimeters (ECal) at future colliders experiments, 2) the ongoing efforts towards dedicated MAPS for the Electron-Ion Collider (EIC) at BNL, for which the EIC Silicon Consortium was already instantiated, and 3) space-born applications for MeV $γ$-ray experiments with MAPS based trackers (AstroPix).
△ Less
Submitted 28 March, 2022; v1 submitted 14 March, 2022;
originally announced March 2022.
-
Simulating MADMAX in 3D: Requirements for Dielectric Axion Haloscopes
Authors:
S. Knirck,
J. Schütte-Engel,
S. Beurthey,
D. Breitmoser,
A. Caldwell,
C. Diaconu,
J. Diehl,
J. Egge,
M. Esposito,
A. Gardikiotis,
E. Garutti,
S. Heyminck,
F. Hubaut,
J. Jochum,
P. Karst,
M. Kramer,
C. Krieger,
D. Labat,
C. Lee,
X. Li,
A. Lindner,
B. Majorovits,
S. Martens,
M. Matysek,
E. Öz
, et al. (16 additional authors not shown)
Abstract:
We present 3D calculations for dielectric haloscopes such as the currently envisioned MADMAX experiment. For ideal systems with perfectly flat, parallel and isotropic dielectric disks of finite diameter, we find that a geometrical form factor reduces the emitted power by up to $30\,\%$ compared to earlier 1D calculations. We derive the emitted beam shape, which is important for antenna design. We…
▽ More
We present 3D calculations for dielectric haloscopes such as the currently envisioned MADMAX experiment. For ideal systems with perfectly flat, parallel and isotropic dielectric disks of finite diameter, we find that a geometrical form factor reduces the emitted power by up to $30\,\%$ compared to earlier 1D calculations. We derive the emitted beam shape, which is important for antenna design. We show that realistic dark matter axion velocities of $10^{-3} c$ and inhomogeneities of the external magnetic field at the scale of $10\,\%$ have negligible impact on the sensitivity of MADMAX. We investigate design requirements for which the emitted power changes by less than $20\,\%$ for a benchmark boost factor with a bandwidth of $50\,{\rm MHz}$ at $22\,{\rm GHz}$, corresponding to an axion mass of $90\,μ{\rm eV}$. We find that the maximum allowed disk tilt is $100\,μ{\rm m}$ divided by the disk diameter, the required disk planarity is $20\,μ{\rm m}$ (min-to-max) or better, and the maximum allowed surface roughness is $100\,μ{\rm m}$ (min-to-max). We show how using tiled dielectric disks glued together from multiple smaller patches can affect the beam shape and antenna coupling.
△ Less
Submitted 13 October, 2021; v1 submitted 13 April, 2021;
originally announced April 2021.
-
An Update to the Letter of Intent for MATHUSLA: Search for Long-Lived Particles at the HL-LHC
Authors:
Cristiano Alpigiani,
Juan Carlos Arteaga-Velázquez,
Austin Ball,
Liron Barak,
Jared Barron,
Brian Batell,
James Beacham,
Yan Benhammo,
Karen Salomé Caballero-Mora,
Paolo Camarri,
Roberto Cardarelli,
John Paul Chou,
Wentao Cui,
David Curtin,
Miriam Diamond,
Keith R. Dienes,
Liam Andrew Dougherty,
Giuseppe Di Sciascio,
Marco Drewes,
Erez Etzion,
Rouven Essig,
Jared Evans,
Arturo Fernández Téllez,
Oliver Fischer,
Jim Freeman
, et al. (58 additional authors not shown)
Abstract:
We report on recent progress in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC, updating the information in the original Letter of Intent (LoI), see CDS:LHCC-I-031, arXiv:1811.00927. A suitable site has been identified at LHC Point 5 that is closer to the CMS Interaction Point (IP) than assumed in the LoI. The decay volume has been increased from 20 m to 25 m…
▽ More
We report on recent progress in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC, updating the information in the original Letter of Intent (LoI), see CDS:LHCC-I-031, arXiv:1811.00927. A suitable site has been identified at LHC Point 5 that is closer to the CMS Interaction Point (IP) than assumed in the LoI. The decay volume has been increased from 20 m to 25 m in height. Engineering studies have been made in order to locate much of the decay volume below ground, bringing the detector even closer to the IP. With these changes, a 100 m x 100 m detector has the same physics reach for large c$τ$ as the 200 m x 200 m detector described in the LoI and other studies. The performance for small c$τ$ is improved because of the proximity to the IP. Detector technology has also evolved while retaining the strip-like sensor geometry in Resistive Plate Chambers (RPC) described in the LoI. The present design uses extruded scintillator bars read out using wavelength shifting fibers and silicon photomultipliers (SiPM). Operations will be simpler and more robust with much lower operating voltages and without the use of greenhouse gases. Manufacturing is straightforward and should result in cost savings. Understanding of backgrounds has also significantly advanced, thanks to new simulation studies and measurements taken at the MATHUSLA test stand operating above ATLAS in 2018. We discuss next steps for the MATHUSLA collaboration, and identify areas where new members can make particularly important contributions.
△ Less
Submitted 3 September, 2020;
originally announced September 2020.
-
MADMAX Status Report
Authors:
S. Beurthey,
N. Böhmer,
P. Brun,
A. Caldwell,
L. Chevalier,
C. Diaconu,
G. Dvali,
P. Freire,
E. Garutti,
C. Gooch,
A. Hambarzumjan,
S. Heyminck,
F. Hubaut,
J. Jochum,
P. Karst,
S. Khan,
D. Kittlinger,
S. Knirck,
M. Kramer,
C. Krieger,
T. Lasserre,
C. Lee,
X. Li,
A. Lindner,
B. Majorovits
, et al. (20 additional authors not shown)
Abstract:
In this report we present the status of the MAgnetized Disk and Mirror Axion eXperiment (MADMAX), the first dielectric haloscope for the direct search of dark matter axions in the mass range of 40 to 400 $μ$eV. MADMAX will consist of several parallel dielectric disks, which are placed in a strong magnetic field and with adjustable separations. This setting is expected to allow for an observable em…
▽ More
In this report we present the status of the MAgnetized Disk and Mirror Axion eXperiment (MADMAX), the first dielectric haloscope for the direct search of dark matter axions in the mass range of 40 to 400 $μ$eV. MADMAX will consist of several parallel dielectric disks, which are placed in a strong magnetic field and with adjustable separations. This setting is expected to allow for an observable emission of axion induced electromagnetic waves at a frequency between 10 and 100 GHz corresponding to the axion mass. The present document orignated from a status report to the DESY PRC in 2019.
△ Less
Submitted 28 October, 2020; v1 submitted 24 March, 2020;
originally announced March 2020.
-
Quantum efficiency enhancement of bialkali photocathodes by an atomically thin layer on substrates
Authors:
Hisato Yamaguchi,
Fangze Liu,
Jeffrey DeFazio,
Mengjia Gaowei,
Lei Guo,
Anna Alexander,
Seong In Yoon,
Chohee Hyun,
Matthew Critchley,
John Sinsheimer,
Vitaly Pavlenko,
Derek Strom,
Kevin L. Jensen,
Daniel Finkenstadt,
Hyeon Suk Shin,
Masahiro Yamamoto,
John Smedley,
Nathan A. Moody
Abstract:
We report quantum efficiency (QE) enhancements in accelerator technology relevant antimonide photocathodes (K2CsSb) by interfacing them with atomically thin two-dimensional (2D) crystal layers. The enhancement occurs in a reflection mode, when a 2D crystal is placed in between the photocathodes and optically reflective substrates. Specifically, the peak QE at 405 nm (3.1 eV) increases by a relativ…
▽ More
We report quantum efficiency (QE) enhancements in accelerator technology relevant antimonide photocathodes (K2CsSb) by interfacing them with atomically thin two-dimensional (2D) crystal layers. The enhancement occurs in a reflection mode, when a 2D crystal is placed in between the photocathodes and optically reflective substrates. Specifically, the peak QE at 405 nm (3.1 eV) increases by a relative 10 percent, while the long wavelength response at 633 nm (2.0 eV) increases by a relative 36 percent on average and up to 80 percent at localized hot spot regions when photocathodes are deposited onto graphene coated stainless steel. There is a similar effect for photocathodes deposited on hexagonal boron nitride monolayer coatings using nickel substrates. The enhancement does not occur when reflective substrates are replaced with optically transparent sapphire. Optical transmission, X-ray diffraction (XRD) and X-ray fluorescence (XRF) revealed that thickness, crystal orientation, quality and elemental stoichiometry of photocathodes do not appreciably change due to 2D crystal coatings. These results suggest optical interactions are responsible for the QE enhancements when 2D crystal sublayers are present on reflective substrates, and provide a pathway toward a simple method of QE enhancement in semiconductor photocathodes by an atomically thin 2D crystal on substrates.
△ Less
Submitted 2 October, 2019;
originally announced October 2019.
-
SENSE: A comparison of photon detection efficiency and optical crosstalk of various SiPM devices
Authors:
A. Nagai,
C. Alispach,
T. Berghöfer,
G. Bonanno,
V. Coco,
D. della Volpe,
A. Haungs,
M. Heller,
K. Henjes-Kunst,
R. Mirzoyan,
T. Montaruli,
G. Romeo,
Y. Renier,
H. C. Schultz-Coulon,
W. Shen,
D. Strom,
H. Tajima,
I. Troyano-Pujadas
Abstract:
This paper describes a comparison of photon detection efficiency and optical crosstalk measurements performed by three partners: Geneva University, Catania Observatory and Nagoya University. The measurements were compared for three different SiPM devices with different active areas: from 9 $mm^2$ up to 93.6 $mm^2$ produced by Hamamatsu. The objective of this work is to establish the measurements a…
▽ More
This paper describes a comparison of photon detection efficiency and optical crosstalk measurements performed by three partners: Geneva University, Catania Observatory and Nagoya University. The measurements were compared for three different SiPM devices with different active areas: from 9 $mm^2$ up to 93.6 $mm^2$ produced by Hamamatsu. The objective of this work is to establish the measurements and analysis procedures for calculating the main SiPM parameters and their precision. This work was done in the scope of SENSE project which aims to build roadmap for the last developments in field of sensors for low light level detection.
△ Less
Submitted 26 February, 2019; v1 submitted 11 December, 2017;
originally announced December 2017.
-
Trap** in irradiated p-on-n silicon sensors at fluences anticipated at the HL-LHC outer tracker
Authors:
W. Adam,
T. Bergauer,
M. Dragicevic,
M. Friedl,
R. Fruehwirth,
M. Hoch,
J. Hrubec,
M. Krammer,
W. Treberspurg,
W. Waltenberger,
S. Alderweireldt,
W. Beaumont,
X. Janssen,
S. Luyckx,
P. Van Mechelen,
N. Van Remortel,
A. Van Spilbeeck,
P. Barria,
C. Caillol,
B. Clerbaux,
G. De Lentdecker,
D. Dobur,
L. Favart,
A. Grebenyuk,
Th. Lenzi
, et al. (663 additional authors not shown)
Abstract:
The degradation of signal in silicon sensors is studied under conditions expected at the CERN High-Luminosity LHC. 200 $μ$m thick n-type silicon sensors are irradiated with protons of different energies to fluences of up to $3 \cdot 10^{15}$ neq/cm$^2$. Pulsed red laser light with a wavelength of 672 nm is used to generate electron-hole pairs in the sensors. The induced signals are used to determi…
▽ More
The degradation of signal in silicon sensors is studied under conditions expected at the CERN High-Luminosity LHC. 200 $μ$m thick n-type silicon sensors are irradiated with protons of different energies to fluences of up to $3 \cdot 10^{15}$ neq/cm$^2$. Pulsed red laser light with a wavelength of 672 nm is used to generate electron-hole pairs in the sensors. The induced signals are used to determine the charge collection efficiencies separately for electrons and holes drifting through the sensor. The effective trap** rates are extracted by comparing the results to simulation. The electric field is simulated using Synopsys device simulation assuming two effective defects. The generation and drift of charge carriers are simulated in an independent simulation based on PixelAV. The effective trap** rates are determined from the measured charge collection efficiencies and the simulated and measured time-resolved current pulses are compared. The effective trap** rates determined for both electrons and holes are about 50% smaller than those obtained using standard extrapolations of studies at low fluences and suggests an improved tracker performance over initial expectations.
△ Less
Submitted 7 May, 2015;
originally announced May 2015.
-
Development of Readout Interconnections for the Si-W Calorimeter of SiD
Authors:
M. Woods,
R. G. Fields,
B. Holbrook,
R. L. Lander,
A. Moskaleva,
C. Neher,
J. Pasner,
M. Tripathi,
J. E. Brau,
R. E. Frey,
D. Strom,
M. Breidenbach,
D. Freytag,
G. Haller,
R. Herbst,
T. Nelson,
S. Schier,
B. Schumm
Abstract:
The SiD collaboration is develo** a Si-W sampling electromagnetic calorimeter, with anticipated application for the International Linear Collider. Assembling the modules for such a detector will involve special bonding technologies for the interconnections, especially for attaching a silicon detector wafer to a flex cable readout bus. We review the interconnect technologies involved, including o…
▽ More
The SiD collaboration is develo** a Si-W sampling electromagnetic calorimeter, with anticipated application for the International Linear Collider. Assembling the modules for such a detector will involve special bonding technologies for the interconnections, especially for attaching a silicon detector wafer to a flex cable readout bus. We review the interconnect technologies involved, including oxidation removal processes, pad surface preparation, solder ball selection and placement, and bond quality assurance. Our results show that solder ball bonding is a promising technique for the Si-W ECAL, and unresolved issues are being addressed.
△ Less
Submitted 21 November, 2011; v1 submitted 31 October, 2011;
originally announced October 2011.
-
Chronopixel Vertex Detectors for Future Linear Colliders
Authors:
C. Baltay,
W. Emmet,
D. Rabinowitz,
J. Brau,
N. Sinev,
D. Strom
Abstract:
Over the past few years we have developed, in collaboration with the SARNOFF Corporation, a design of a Monolithic CMOS Pixel Detector for ILC Vertex Detectors. The unique feature of this design is that each hit is accompanied by a time tag with sufficient precision to assign each hit to a particular bunch crossing of the ILC (thus the name Chronopixel). This reduces the occupancy even in the inne…
▽ More
Over the past few years we have developed, in collaboration with the SARNOFF Corporation, a design of a Monolithic CMOS Pixel Detector for ILC Vertex Detectors. The unique feature of this design is that each hit is accompanied by a time tag with sufficient precision to assign each hit to a particular bunch crossing of the ILC (thus the name Chronopixel). This reduces the occupancy even in the innermost Vertex Detector layer to negligible levels, allowing a robust Vertex Detector even in the case that the backgrounds in the ILC are higher than presently estimated.
△ Less
Submitted 13 September, 2011;
originally announced September 2011.
-
The Layer 0 Inner Silicon Detector of the D0 Experiment
Authors:
R. Angstadt,
L. Bagby,
A. Bean,
T. Bolton,
D. Buchholz,
D. Butler,
L. Christofek,
W. E. Cooper,
C. H. Daly,
M. Demarteau,
J. Foglesong,
C. E. Gerber,
H. Gonzalez,
J. Green,
H. Guldenman,
K. Hanagaki,
K. Herner,
J. Howell,
M. Hrycyk,
M. Johnson,
M. Kirby,
K. Krempetz,
W. Kuykendall,
F. Lehner,
R. Lipton
, et al. (24 additional authors not shown)
Abstract:
This paper describes the design, fabrication, installation and performance of the new inner layer called Layer 0 (L0) that was inserted in the existing Run IIa Silicon Micro-Strip Tracker (SMT) of the D0 experiment at the Fermilab Tevatron collider. L0 provides tracking information from two layers of sensors, which are mounted with center lines at a radial distance of 16.1 mm and 17.6 mm respect…
▽ More
This paper describes the design, fabrication, installation and performance of the new inner layer called Layer 0 (L0) that was inserted in the existing Run IIa Silicon Micro-Strip Tracker (SMT) of the D0 experiment at the Fermilab Tevatron collider. L0 provides tracking information from two layers of sensors, which are mounted with center lines at a radial distance of 16.1 mm and 17.6 mm respectively from the beam axis. The sensors and readout electronics are mounted on a specially designed and fabricated carbon fiber structure that includes cooling for sensor and readout electronics. The structure has a thin polyimide circuit bonded to it so that the circuit couples electrically to the carbon fiber allowing the support structure to be used both for detector grounding and a low impedance connection between the remotely mounted hybrids and the sensors.
△ Less
Submitted 12 November, 2009;
originally announced November 2009.
-
Status of the Chronopixel Project
Authors:
C. Baltay,
J. Brau,
W. Emmet,
D. Rabinovich,
N. Sinev,
D. Strom
Abstract:
Other the past few years we have developed a monolithic CMOS pixel detector design for the ILC in collaboration with the SARNOFF Corporation. The unique feature of this design is the recorded time tag for each hit, allowing assignment of the hit to a particular bunch crossing (thus the name Chronopixel). The prototype design was completed in 2007. The first set of prototype devices was fabricate…
▽ More
Other the past few years we have developed a monolithic CMOS pixel detector design for the ILC in collaboration with the SARNOFF Corporation. The unique feature of this design is the recorded time tag for each hit, allowing assignment of the hit to a particular bunch crossing (thus the name Chronopixel). The prototype design was completed in 2007. The first set of prototype devices was fabricated in 2008. We have developed a detailed testing plan and have designed the test electronics in collaboration with SLAC. Testing is expected to start early in 2009.
△ Less
Submitted 12 February, 2009;
originally announced February 2009.
-
A Silicon-Tungsten ECal with Integrated Electronics
Authors:
R. Frey,
J. Brau,
M. Breidenbach,
D. Freytag,
G. Haller,
R. Herbst,
R. Lander,
T. Nelson,
V. Radeka,
D. Strom,
M. Tripathi
Abstract:
We summarize recent R&D progress for a silicon-tungsten electromagnetic calorimeter (ECal) with integrated electronics, designed to meet the ILC physics requirements.
We summarize recent R&D progress for a silicon-tungsten electromagnetic calorimeter (ECal) with integrated electronics, designed to meet the ILC physics requirements.
△ Less
Submitted 11 October, 2007;
originally announced October 2007.
