Showing 1–28 of 28 results for author: Spataro, S

Track-based alignment for the BESIII CGEM detector in the cosmic-ray test

Authors: A. Q. Guo, L. H. Wu, L. L. Wang, R. E. Mitchell, A. Amoroso, R. Baldini Ferroli, I. Balossino, M. Bertani, D. Bettoni, F. Bianchi, A. Bortone, G. Cibinetto, A. Cotta Ramusino, F. Cossio, M. Y. Dong, M. Da Rocha Rolo, F. De Mori, M. Destefanis, J. Dong, F. Evangelisti, R. Farinelli, L. Fava, G. Felici, I. Garzia, M. Gatta , et al. (27 additional authors not shown)

Abstract: The Bei**g Electron Spectrometer III (BESIII) is a multipurpose detector operating on the Bei**g Electron Positron Collider II (BEPCII). After more than ten year's operation, the efficiency of the inner layers of the Main Drift Chamber (MDC) decreased significantly. To solve this issue, the BESIII collaboration is planning to replace the inner part of the MDC with three layers of Cylindrical tri… ▽ More The Bei**g Electron Spectrometer III (BESIII) is a multipurpose detector operating on the Bei**g Electron Positron Collider II (BEPCII). After more than ten year's operation, the efficiency of the inner layers of the Main Drift Chamber (MDC) decreased significantly. To solve this issue, the BESIII collaboration is planning to replace the inner part of the MDC with three layers of Cylindrical triple Gas Electron Multipliers (CGEM). The transverse plane spatial resolution of CGEM is required to be 120 $μ$m or better. To meet this goal, a careful calibration of the detector is necessary to fully exploit the potential of the CGEM detector. In all the calibrations, the detector alignment plays an important role to improve the detector precision. The track-based alignment for the CGEM detector with the Millepede algorithm is implemented to reduce the uncertainties of the hit position measurement. Using the cosmic-ray data taken in 2020 with the two layers setup, the displacement and rotation of the outer layer with respect to the inner layer is determined by a simultaneous fit applied to more than 160000 tracks. A good alignment precision has been achieved that guarantees the design request could be satisfied in the future. A further alignment is going to be performed using the combined information of tracks from cosmic-ray and collisions after the CGEM is installed into the BESIII detector. △ Less

Submitted 14 December, 2022; v1 submitted 2 November, 2022; originally announced November 2022.

The CGEM-IT readout chain

Authors: A. Amoroso, R. Baldini Ferroli, I. Balossino, M. Bertani, D. Bettoni, F. Bianchi, A. Bortone, R. Bugalho, A. Calcaterra, S. Cerioni, S. Chiozzi, G. Cibinetto, A. Cotta Ramusino, F. Cossio, M. Da Rocha Rolo, F. De Mori, M. Destefanis, A. Di Francesco, F. Evangelisti, R. Farinelli, L. Fava, G. Felici, S. Garbolino, I. Garzia, M. Gatta , et al. (22 additional authors not shown)

Abstract: An innovative Cylindrical Gas Electron Multiplier (CGEM) detector is under construction for the upgrade of the inner tracker of the BESIII experiment. A novel system has been worked out for the readout of the CGEM detector, including a new ASIC, dubbed TIGER -Torino Integrated GEM Electronics for Readout, designed for the amplification and digitization of the CGEM output signals. The data output b… ▽ More An innovative Cylindrical Gas Electron Multiplier (CGEM) detector is under construction for the upgrade of the inner tracker of the BESIII experiment. A novel system has been worked out for the readout of the CGEM detector, including a new ASIC, dubbed TIGER -Torino Integrated GEM Electronics for Readout, designed for the amplification and digitization of the CGEM output signals. The data output by TIGER are collected and processed by a first FPGA-based module, GEM Read Out Card, in charge of configuration and control of the front-end ASICs. A second FPGA-based module, named GEM Data Concentrator, builds the trigger selected event packets containing the data and stores them via the main BESIII data acquisition system. The design of the electronics chain, including the power and signal distribution, will be presented together with its performance. △ Less

Submitted 17 August, 2021; v1 submitted 19 May, 2021; originally announced May 2021.

PARSIFAL: a toolkit for triple-GEM parametrized simulation

Authors: A. Amoroso, R. Baldini Ferroli, I. Balossino, M. Bertani, D. Bettoni, F. Bianchi, A. Bortone, A. Calcaterra, S. Cerioni, W. Cheng, G. Cibinetto, A. Cotta Ramusino, F. Cossio, M. Da Rocha Rolo, F. De Mori, M. Destefanis, J. Dong, F. Evangelisti, R. Farinelli, L. Fava, G. Felici, I. Garzia, M. Gatta, G. Giraudo, S. Gramigna , et al. (16 additional authors not shown)

Abstract: PARSIFAL (PARametrized SImulation by Farinelli And Lavezzi) is a fast and reliable software tool that reproduces the complete response of a triple-GEM detector to the passage of a charged particle, taking into account the main physical effects. Starting from the detector configuration and the particle information, PARSIFAL reproduces ionization, spatial and temporal diffusion, effect of magnetic f… ▽ More PARSIFAL (PARametrized SImulation by Farinelli And Lavezzi) is a fast and reliable software tool that reproduces the complete response of a triple-GEM detector to the passage of a charged particle, taking into account the main physical effects. Starting from the detector configuration and the particle information, PARSIFAL reproduces ionization, spatial and temporal diffusion, effect of magnetic field, if present, and GEM amplification to provide the dependable triple-GEM detector response. In the design and optimization stages of this kind of detectors, simulations play an important role. Accurate and robust software programs, such as GARFIELD++, can simulate the transport of electrons and ions in a gas medium and their interaction with the electric field, but they are CPU-time consuming. The necessity to reduce the processing time while maintaining the precision of a full simulation is the main driver of this work. For a given set of geometrical and electrical settings, GARFIELD++ is run once-and-for-all to provide the input parameters for PARSIFAL. Once PARSIFAL is initialized and run, it produces the detector output, including the signal induction and the output of the electronics. The results of the analysis of the simulated data obtained with PARSIFAL are compared with the results of the experimental data collected during a testbeam: some tuning factors are applied to the simulation to improve the agreement. This paper describes the structure of the code and the methodology used to match the output to the experimental data. △ Less

Submitted 7 June, 2023; v1 submitted 9 May, 2020; originally announced May 2020.

Comments: submitted to Computer Physics Communications, CPiC

Time performance of a triple-GEM detector at high rate

Authors: A. Amoroso, R. Baldini Ferroli, I. Balossino, M. Bertani, D. Bettoni, A. Bortone, A. Calcaterra, S. Cerioni, W. Cheng, G. Cibinetto, A. Cotta Ramusino, F. Cossio, M. Da Rocha Rolo, F. De Mori, A. Denig, M. Destefanis, J. Dong, F. Evangelisti, R. Farinelli, L. Fava, G. Felici, B. Garillon, I. Garzia, M. Gatta, G. Giraudo , et al. (23 additional authors not shown)

Abstract: Gaseous detectors are used in high energy physics as trackers or, more generally, as devices for the measurement of the particle position. For this reason, they must provide high spatial resolution and they have to be able to operate in regions of intense radiation, i.e. around the interaction point of collider machines. Among these, Micro Pattern Gaseous Detectors (MPGD) are the latest frontier a… ▽ More Gaseous detectors are used in high energy physics as trackers or, more generally, as devices for the measurement of the particle position. For this reason, they must provide high spatial resolution and they have to be able to operate in regions of intense radiation, i.e. around the interaction point of collider machines. Among these, Micro Pattern Gaseous Detectors (MPGD) are the latest frontier and allow to overcome many limitations of the pre-existing detectors, such as the radiation tolerance and the rate capability. The gas Electron Multiplier (GEM) is a MPGD that exploits an intense electric field in a reduced amplification region in order to prevent discharges. Several amplification stages, like in a triple-GEM, allow to increase the detector gain and to reduce the discharge probability. Reconstruction techniques such as charge centroid (CC) and micro-Time Projection Chamber ($\upmu$TPC) are used to perform the position measurement. From literature triple-GEMs show a stable behaviour up to $10^8\,$Hz/cm$^2$. A testbeam with four planar triple-GEMs has been performed at the Mainz Microtron (MAMI) facility and their performance was evaluated in different beam conditions. In this article a focus on the time performance for the $\upmu$TPC clusterization is given and a new measurement of the triple-GEM limits at high rate will be presented. △ Less

Submitted 10 April, 2020; originally announced April 2020.

Track Finding at Belle II

Authors: Valerio Bertacchi, Tadeas Bilka, Nils Braun, Giulia Casarosa, Luigi Corona, Sam Cunliffe, Filippo Dattola, Gaetano De Marino, Michael De Nuccio, Giacomo De Pietro, Thanh Van Dong, Giulio Dujany, Patrick Ecker, Michael Eliachevitch, Tristan Fillinger, Oliver Frost, Rudolf Fruehwirth, Uwe Gebauer, Alexander Glazov, Nicolas Gosling, Aiqiang Guo, Thomas Hauth, Martin Heck, Mateusz Kaleta, Jakub Kandra , et al. (33 additional authors not shown)

Abstract: This paper describes the track-finding algorithm that is used for event reconstruction in the Belle II experiment operating at the SuperKEKB B-factory in Tsukuba, Japan. The algorithm is designed to balance the requirements of a high efficiency to find charged particles with a good track parameter resolution, a low rate of spurious tracks, and a reasonable demand on CPU resources. The software is… ▽ More This paper describes the track-finding algorithm that is used for event reconstruction in the Belle II experiment operating at the SuperKEKB B-factory in Tsukuba, Japan. The algorithm is designed to balance the requirements of a high efficiency to find charged particles with a good track parameter resolution, a low rate of spurious tracks, and a reasonable demand on CPU resources. The software is implemented in a flexible, modular manner and employs a diverse selection of global and local track-finding algorithms to achieve an optimal performance. △ Less

Submitted 26 November, 2021; v1 submitted 27 March, 2020; originally announced March 2020.

Journal ref: Comput.Phys.Commun. 259 (2021) 107610

Technical Design Report for the PANDA Endcap Disc DIRC

Authors: Panda Collaboration, F. Davi, W. Erni, B. Krusche, M. Steinacher, N. Walford, H. Liu, Z. Liu, B. Liu, X. Shen, C. Wang, J. Zhao, M. Albrecht, T. Erlen, F. Feldbauer, M. Fink, V. Freudenreich, M. Fritsch, F. H. Heinsius, T. Held, T. Holtmann, I. Keshk, H. Koch, B. Kopf, M. Kuhlmann , et al. (441 additional authors not shown)

Abstract: PANDA (anti-Proton ANnihiliation at DArmstadt) is planned to be one of the four main experiments at the future international accelerator complex FAIR (Facility for Antiproton and Ion Research) in Darmstadt, Germany. It is going to address fundamental questions of hadron physics and quantum chromodynamics using cooled antiproton beams with a high intensity and and momenta between 1.5 and 15 GeV/c.… ▽ More PANDA (anti-Proton ANnihiliation at DArmstadt) is planned to be one of the four main experiments at the future international accelerator complex FAIR (Facility for Antiproton and Ion Research) in Darmstadt, Germany. It is going to address fundamental questions of hadron physics and quantum chromodynamics using cooled antiproton beams with a high intensity and and momenta between 1.5 and 15 GeV/c. PANDA is designed to reach a maximum luminosity of 2x10^32 cm^2 s. Most of the physics programs require an excellent particle identification (PID). The PID of hadronic states at the forward endcap of the target spectrometer will be done by a fast and compact Cherenkov detector that uses the detection of internally reflected Cherenkov light (DIRC) principle. It is designed to cover the polar angle range from 5° to 22° and to provide a separation power for the separation of charged pions and kaons up to 3 standard deviations (s.d.) for particle momenta up to 4 GeV/c in order to cover the important particle phase space. This document describes the technical design and the expected performance of the novel PANDA Disc DIRC detector that has not been used in any other high energy physics experiment (HEP) before. The performance has been studied with Monte-Carlo simulations and various beam tests at DESY and CERN. The final design meets all PANDA requirements and guarantees suffcient safety margins. △ Less

Submitted 29 December, 2019; originally announced December 2019.

Comments: TDR for Panda/Fair to be published

Triple GEM performance in magnetic field

Authors: M. Alexeev, A. Amoroso, S. Bagnasco, R. Baldini Ferroli, I. Balossino, G. Bencivenni, M. Bertani, D. Bettoni, F. Bianchi, A. Bortone, A. Calcaterra, M. Capodiferro, V. Carassiti, S. Cerioni, J. Chai, W. Cheng, S. Chiozzi, G. Cibinetto, A. Cotta Ramusino, G. Cotto, F. Cossio, M. Da Rocha Rolo, F. De Mori, M. Destefanis, D. Domenici , et al. (43 additional authors not shown)

Abstract: Performance of triple GEM prototypes in strong magnetic field has been evaluated bymeans of a muon beam at the H4 line of the SPS test area at CERN. Data have been reconstructedand analyzed offline with two reconstruction methods: the charge centroid and the micro-Time-Projection-Chamber exploiting the charge and the time measurement respectively. A combinationof the two reconstruction methods is… ▽ More Performance of triple GEM prototypes in strong magnetic field has been evaluated bymeans of a muon beam at the H4 line of the SPS test area at CERN. Data have been reconstructedand analyzed offline with two reconstruction methods: the charge centroid and the micro-Time-Projection-Chamber exploiting the charge and the time measurement respectively. A combinationof the two reconstruction methods is capable to guarantee a spatial resolution better than 150μmin magnetic field up to a 1 T. △ Less

Submitted 17 August, 2019; originally announced August 2019.

GRAAL: Gem Reconstruction And Analysis Library

Authors: R. Farinelli, M. Alexeev, A. Amoroso, S. Bagnasco, R. BaldiniFerroli, I. Balossino, M. Bertani, D. Bettoni, A. Bortone, F. Bianchi, A. Calcaterra, S. Cerioni, J. Chai, W. Cheng, S. Chiozzi, G. Cibinetto, F. Cossio, A. Cotta Ramusino, G. Cotto, M. Da Rocha Rolo, F. De Mori, M. Destefanis, F. Evangelisti, L. Fava, G. Felici , et al. (25 additional authors not shown)

Abstract: MPGD are the new frontier in gas trackers. Among this kind of devices, theGEM chambers are widely used. The experimental signals acquired with the detector mustobviously be reconstructed and analysed. In this contribution, a new offline software to performreconstruction, alignment and analysis on the data collected with APV-25 and TIGER ASICswill be presented. GRAAL (Gem Reconstruction And Analysi… ▽ More MPGD are the new frontier in gas trackers. Among this kind of devices, theGEM chambers are widely used. The experimental signals acquired with the detector mustobviously be reconstructed and analysed. In this contribution, a new offline software to performreconstruction, alignment and analysis on the data collected with APV-25 and TIGER ASICswill be presented. GRAAL (Gem Reconstruction And Analysis Library) is able to measurethe performance of a MPGD detector with a strip segmented anode (presently). The code isdivided in three parts: reconstruction, where the hits are digitized and clusterized; tracking,where a procedure fits the points from the tracking system and uses that information to align thechamber with rotations and shifts; analysis, where the performance is evaluated (e.g. efficiency,spatial resolution,etc.). The user must set the geometry of the setup and then the programreturns automatically the analysis results, taking care of different conditions of gas mixture,electric field, magnetic field, geometries, strip orientation, dead strip, misalignment and manyothers. △ Less

Submitted 8 May, 2019; originally announced May 2019.

A fast and parametric digitization for triple-GEM detectors

Authors: R. Farinelli, M. Alexeev, A. Amoroso, S. Bagnasco, R. Baldini Ferrioli, I. Balossino, M. Bertani, D. Bettoni, A. Bortone, F. Bianchi, A. Calcaterra, S. Cerioni, J. Chai, W. Cheng, S. Chiozzi, G. Cibinetto, F. Cossio, A. Cotta Ramusino, G. Cotto, M. Da Rocha Rolo, F. De Mori, M. Destefanis, F. Evangelisti, L. Fava, G. Felici , et al. (26 additional authors not shown)

Abstract: Triple-GEM detectors are a well known technology in high energy physics. In order to have a complete understanding of their behavior, in parallel with on beam testing, a Monte Carlo code has to be developed to simulate their response to the passage of particles. The software must take into account all the physical processes involved from the primary ionization up to the signal formation, e.g. the… ▽ More Triple-GEM detectors are a well known technology in high energy physics. In order to have a complete understanding of their behavior, in parallel with on beam testing, a Monte Carlo code has to be developed to simulate their response to the passage of particles. The software must take into account all the physical processes involved from the primary ionization up to the signal formation, e.g. the avalanche multiplication and the effect of the diffusion on the electrons. In the case of gas detectors, existing software such as Garfield already perform a very detailed simulation but are CPU time consuming. A description of a reliable but faster simulation is presented here: it uses a parametric description of the variables of interest obtained by suitable preliminary Garfield simulations and tuned to the test beam data. It can reproduce the real values of the charge measured by the strip, needed to reconstruct the position with the Charge Centroid method. In addition, particular attention was put to the simulation of the timing information, which permits to apply also the micro-Time Projection Chamber position reconstruction, for the first time on a triple-GEM. A comparison between simulation and experimental values of some sentinel variables in different conditions of magnetic field, high voltage settings and incident angle will be shown. △ Less

Submitted 12 April, 2019; originally announced April 2019.

Implementation of GENFIT2 as an experiment independent track-fitting framework

Authors: Tadeas Bilka, Nils Braun, Thomas Hauth, Thomas Kuhr, Lia Lavezzi, Felix Metzner, Stephan Paul, Elisabetta Prencipe, Markus Prim, Johannes Rauch, James Ritman, Tobias Schlueter, Stefano Spataro

Abstract: The GENFIT toolkit, initially developed at the Technische Universitaet Muenchen, has been extended and modified to be more general and user-friendly. The new GENFIT, called GENFIT2, provides track representation, track-fitting algorithms and graphic visualization of tracks and detectors, and it can be used for any experiment that determines parameters of charged particle trajectories from spacial… ▽ More The GENFIT toolkit, initially developed at the Technische Universitaet Muenchen, has been extended and modified to be more general and user-friendly. The new GENFIT, called GENFIT2, provides track representation, track-fitting algorithms and graphic visualization of tracks and detectors, and it can be used for any experiment that determines parameters of charged particle trajectories from spacial coordinate measurements. Based on general Kalman filter routines, it can perform extrapolations of track parameters and covariance matrices. It also provides interfaces to Millepede II for alignment purposes, and RAVE for the vertex finder. Results of an implementation of GENFIT2 in basf2 and PandaRoot software frameworks are presented here. △ Less

Submitted 13 February, 2019; v1 submitted 12 February, 2019; originally announced February 2019.

Comments: 41 pages 24 figures, 1 table. Paper submitted to NIM

A Cylindrical GEM Inner Tracker for the BESIII experiment at IHEP

Authors: R. Farinelli, M. Alexeev, A. Amoroso, F. Bianchi, M. Bertani, D. Bettoni, N. Canale, A. Calcaterra, V. Carassiti, S. Cerioni, J. Chai, S. Chiozzi, G. Cibinetto, A. Cotta Ramusino, F. Cossio, F. De Mori, M. Destefanis, T. Edisher, F. Evangelisti, L. Fava, G. Felici, E. Fioravanti, I. Garzia, M. Gatta, M. Greco , et al. (21 additional authors not shown)

Abstract: The Bei**g Electron Spectrometer III (BESIII) is a multipurpose detector that collects data provided by the collision in the Bei**g Electron Positron Collider II (BEPCII), hosted at the Institute of High Energy Physics of Bei**g. Since the beginning of its operation, BESIII has collected the world largest sample of J/ψ and ψ(2s). Due to the increase of the luminosity up to its nominal value of… ▽ More The Bei**g Electron Spectrometer III (BESIII) is a multipurpose detector that collects data provided by the collision in the Bei**g Electron Positron Collider II (BEPCII), hosted at the Institute of High Energy Physics of Bei**g. Since the beginning of its operation, BESIII has collected the world largest sample of J/ψ and ψ(2s). Due to the increase of the luminosity up to its nominal value of 10^33 cm-2 s-1 and aging effect, the MDC decreases its efficiency in the first layers up to 35% with respect to the value in 2014. Since BESIII has to take data up to 2022 with the chance to continue up to 2027, the Italian collaboration proposed to replace the inner part of the MDC with three independent layers of Cylindrical triple-GEM (CGEM). The CGEM-IT project will deploy several new features and innovation with respect the other current GEM based detector: the μTPC and analog readout, with time and charge measurements will allow to reach the 130 μm spatial resolution in 1 T magnetic field requested by the BESIII collaboration. In this proceeding, an update of the status of the project will be presented, with a particular focus on the results with planar and cylindrical prototypes with test beams data. These results are beyond the state of the art for GEM technology in magnetic field. △ Less

Submitted 2 July, 2018; originally announced July 2018.

Innovative design and construction technique for the Cylindrical GEM detector for the BESIII experiment

Authors: A. Amoroso, M. Alexeev, R. Baldini Ferroli, M. Bertani, D. Bettoni, F. Bianchi, A. Calcaterra, N. Canale, M. Capodiferro, V. Carassiti, S. Cerioni, JY. Chai, S. Chiozzi, G. Cibinetto, F. Cossio, A. Cotta Ramusino, F. De Mori, M. Destefanis, J. Dong, F. Evangelisti, R. Farinelli, L. Fava, G. Felici, E. Fioravanti, I. Garzia , et al. (27 additional authors not shown)

Abstract: Gas detector are very light instrument used in high energy physics to measure the particle properties: position and momentum. Through high electric field is possible to use the Gas Electron Multiplier (GEM) technology to detect the particles and to exploit the its properties to construct a large area detector, such as the new IT for BESIII. The state of the art in the GEM production allow to creat… ▽ More Gas detector are very light instrument used in high energy physics to measure the particle properties: position and momentum. Through high electric field is possible to use the Gas Electron Multiplier (GEM) technology to detect the particles and to exploit the its properties to construct a large area detector, such as the new IT for BESIII. The state of the art in the GEM production allow to create very large area GEM foils (up to 50x100 cm2) and thanks to the small thickness of these foil is it possible to shape it to the desired form: a Cylindrical Gas Electron Multiplier (CGEM) is then proposed. The innovative construction technique based on Rohacell, a PMI foam, will give solidity to cathode and anode with a very low impact on material budget. The entire detector is sustained by permaglass rings glued at the edges. These rings are use to assembly the CGEM together with a dedicated Vertical Insertion System and moreover there is placed the On-Detector electronic. The anode has been improved w.r.t. the state of the art through a jagged readout that minimize the inter-strip capacitance. The mechanical challenge of this detector requires a precision of the entire geometry within few hundreds of microns in the whole area. In this presentation will be presented an overview of the construction technique and the validation of this technique through the realization of a CGEM and its first tests. These activities are performed within the framework of the BESIIICGEM Project (645664), funded by the European Commission in the action H2020-RISE-MSCA-2014. △ Less

Submitted 21 March, 2018; originally announced March 2018.

Comments: Proceedings for "Technology and Instrumentation in Particle Physics 2017" (TIPP2017) Conference, 22-26 May 2017, Bei**g, China

Test beam results of a Cylindrical GEM detector for the BESIII experiment

Authors: G. Mezzadri, M. Alexeev, A. Amoroso, R. Baldini Ferroli, M. Bertani, D. Bettoni, F. Bianchi, A. Calcaterra, N. Canale, M. Capodiferro, V. Carassiti, S. Cerioni, JY. Chai, S. Chiozzi, G. Cibinetto, F. Cossio, A. Cotta Ramusino, F. De Mori, M. Destefanis, J. Dong, F. Evangelisti, R. Farinelli, L. Fava, G. Felici, E. Fioravanti , et al. (28 additional authors not shown)

Abstract: Gas detector are very light instrument used in high energy physics to measure the particle properties: position and momentum. Through high electric field is possible to use the Gas Electron Multiplier (GEM) technology to detect the charged particles and to exploit their properties to construct a large area detector, such as the new IT for BESIII. The state of the art in the GEM production allows t… ▽ More Gas detector are very light instrument used in high energy physics to measure the particle properties: position and momentum. Through high electric field is possible to use the Gas Electron Multiplier (GEM) technology to detect the charged particles and to exploit their properties to construct a large area detector, such as the new IT for BESIII. The state of the art in the GEM production allows to create very large area GEM foils (up to 50x100 $\mathrm{cm}^2$) and thanks to the small thickness of these foils is it possible to shape it to the desired form: a Cylindrical Gas Electron Multiplier (CGEM) is then proposed. The innovative construction technique based on Rohacell, a PMI foam, will give solidity to cathode and anode with a very low impact on material budget. The entire detector is sustained by Permaglass rings glued at the edges. These rings are used to assembly the CGEM, together with a dedicated Vertical Insertion System and moreover they host the On-Detector electronic. The anode has been improved w.r.t. the state of the art through a jagged readout that minimize the inter-strip capacitance. The mechanical challenge of this detector requires a precision of the entire geometry within few hundreds of microns in the whole area. In this contribution an overview of the construction technique, the validation of this technique through the realization of a CGEM, and its first tests will be presented. These activities are performed within the framework of the BESIIICGEM Project (645664), funded by the European Commission in the action H2020-RISE-MSCA-2014. △ Less

Submitted 20 March, 2018; originally announced March 2018.

Comments: 10 pages, 7 figures. Proceedings of 5th International Conference on Micro-Pattern Gas Detectors (MPGD2017), Philadelphia 22-26 May 2017

Performance of the micro-TPC Reconstruction for GEM Detectors at High Rate

Authors: L. Lavezzi, M. Alexeev, A. Amoroso, R. Baldini Ferroli, M. Bertani, D. Bettoni, F. Bianchi, A. Calcaterra, N. Canale, M. Capodiferro, V. Carassiti, S. Cerioni, JY. Chai, S. Chiozzi, G. Cibinetto, F. Cossio, A. Cotta Ramusino, F. De Mori, M. Destefanis, J. Dong, F. Evangelisti, R. Farinelli, L. Fava, G. Felici, E. Fioravanti , et al. (27 additional authors not shown)

Abstract: Gas detectors are one of the pillars of the research in fundamental physics. Since many years, a new concept of detectors, the Micro Pattern Gas Detectors, allows to overcome many of the problems of other types of commonly used detectors, as drift chambers and microstrips, reducing the discharge rate and increasing the radiation tolerance. Among these, one of the most commonly used is the Gas Elec… ▽ More Gas detectors are one of the pillars of the research in fundamental physics. Since many years, a new concept of detectors, the Micro Pattern Gas Detectors, allows to overcome many of the problems of other types of commonly used detectors, as drift chambers and microstrips, reducing the discharge rate and increasing the radiation tolerance. Among these, one of the most commonly used is the Gas Electron Multiplier. Commonly deployed as fast timing detectors and triggers, due to their fast response, high rate capability and high radiation hardness, they can also be used as trackers. The center of gravity readout technique allows to overcome the limit of the digital pads, whose spatial resolution is constrained by the pitch size. The presence of a high external magnetic field can distort the electronic cloud and affect the spatial resolution. The micro-TPC reconstruction method allows to reconstruct the three dimensional particle position as in a traditional Time Projection Chamber, but within a drift gap of a few millimeters. This method brings these detectors into a new perspective for what concerns the spatial resolution in strong magnetic field. In this report, the basis of this new technique will be shown and it will be compared to the traditional center of gravity. The results of a series of test beam performed with 10 x 10 cm2 planar prototypes in magnetic field will also be presented. This is one of the first implementations of this technique for GEM detectors in magnetic field and allows to reach unprecedented performance for gas detectors, up to a limit of 120 micron at 1T, one of the world's best results for MPGDs in strong magnetic field. The micro-TPC reconstruction has been recently tested at very high rates in a test beam at the MAMI facility; preliminary results of the test will be presented. △ Less

Submitted 20 March, 2018; originally announced March 2018.

Comments: Proceedings for "2017 IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC)" (IEEE17) Conference, 21-28 October 2017, Atlanga, Georgia, USA (prepared for submission to IEEE Conference Record)

Test beam results with prototypes for the new Cylindrical GEM Inner Tracker of the BESIII experiment

Authors: L. Lavezzi, M. Alexeev, A. Amoroso, R. Baldini Ferroli, M. Bertani, D. Bettoni, F. Bianchi, A. Calcaterra, N. Canale, M. Capodiferro, V. Carassiti, S. Cerioni, JY. Chai, S. Chiozzi, G. Cibinetto, F. Cossio, A. Cotta Ramusino, F. De Mori, M. Destefanis, J. Dong, F. Evangelisti, R. Farinelli, L. Fava, G. Felici, E. Fioravanti , et al. (27 additional authors not shown)

Abstract: A cylindrical GEM tracker is under construction in order to replace and improve the inner tracking system of the BESIII experiment. Tests with planar chamber prototypes were carried out on the H4 beam line of SPS (CERN) with muons of 150 GeV/c momentum, to evaluate the efficiency and resolution under different working conditions. The obtained efficiency was in the 96 - 98% range. Two complementary… ▽ More A cylindrical GEM tracker is under construction in order to replace and improve the inner tracking system of the BESIII experiment. Tests with planar chamber prototypes were carried out on the H4 beam line of SPS (CERN) with muons of 150 GeV/c momentum, to evaluate the efficiency and resolution under different working conditions. The obtained efficiency was in the 96 - 98% range. Two complementary algorithms for the position determination were developed: the charge centroid and the micro-TPC methods. With the former, resolutions <100 micron and <200 micron were achieved without and with magnetic field, respectively. The micro-TPC improved these results. By the end of 2016, the first cylindrical prototype was tested on the same beam line. It showed optimal stability under different settings. The comparison of its performance with respect to the planar chambers is ongoing. Here, the results of the planar prototype tests will be addressed. △ Less

Submitted 20 March, 2018; originally announced March 2018.

Comments: Proceedings for "Incontri di Fisica delle Alte Energie 2017" (IFAE17) Conference, 19-21 April 2017, Trieste, Italy (prepared for submission to Nuovo Cimento C - Colloquia on Physics)

The new cylindrical GEM inner tracker of BESIII

Authors: L. Lavezzi, M. Alexeev, A. Amoroso, R. Baldini Ferroli, M. Bertani, D. Bettoni, F. Bianchi, A. Calcaterra, N. Canale, M. Capodiferro, V. Carassiti, S. Cerioni, JY. Chai, S. Chiozzi, G. Cibinetto, F. Cossio, A. Cotta Ramusino, F. De Mori, M. Destefanis, J. Dong, F. Evangelisti, R. Farinelli, L. Fava, G. Felici, E. Fioravanti , et al. (27 additional authors not shown)

Abstract: The Cylindrical GEM-Inner Tracker (CGEM-IT) is the upgrade of the internal tracking system of the BESIII experiment. It consists of three layers of cylindrically-shaped triple GEMs, with important innovations with respect to the existing GEM detectors, in order to achieve the best performance with the lowest material budget. It will be the first cylindrical GEM running with analog readout inside a… ▽ More The Cylindrical GEM-Inner Tracker (CGEM-IT) is the upgrade of the internal tracking system of the BESIII experiment. It consists of three layers of cylindrically-shaped triple GEMs, with important innovations with respect to the existing GEM detectors, in order to achieve the best performance with the lowest material budget. It will be the first cylindrical GEM running with analog readout inside a 1T magnetic field. The simultaneous measurement of both the deposited charge and the signal time will permit to use a combination of two algorithms to evaluate the spatial position of the charged tracks inside the CGEM-IT: the charge centroid and the micro time projection chamber modes. They are complementary and can cope with the asymmetry of the electron avalanche when running in magnetic field and with non-orthogonal incident tracks. To evaluate the behavior under different working settings, both planar chambers and the first cylindrical prototype have been tested during various test beams at CERN with 150 GeV/c muons and pions. This paper reports the results obtained with the two reconstruction methods and a comparison between the planar and cylindrical chambers. △ Less

Submitted 20 March, 2018; originally announced March 2018.

Comments: Proceedings for "Particles and Nuclei International Conference 2017" (PANIC17) Conference, 1-5 September 2017, Bei**g, China (prepared for submission to International Journal of Modern Physics: Conference Series)

Development and Test of a uTPC Cluster Reconstruction for a Triple GEM Detector in Strong Magnetic Field

Authors: R. Farinelli, M. Alexeev, A. Amoroso, F. Bianchi, M. Bertani, D. Bettoni, N. Canale, A. Calcaterra, V. Carassiti, S. Cerioni, J. Chai, S. Chiozzi, G. Cibinetto, A. Cotta Ramusino, F. Cossio, F. De Mori, M. Destefanis, T. Edisher, F. Evangelisti, L. Fava, G. Felici, E. Fioravanti, I. Garzia, M. Gatta, M. Greco , et al. (21 additional authors not shown)

Abstract: Performance of triple GEM prototypes has been evaluated by means of a muon beam at the H4 line of the SPS test area at CERN. The data from two planar prototypes have been reconstructed and analyzed offline with two clusterization methods: the enter of gravity of the charge distribution and the micro Time Projection Chamber (\muTPC). Concerning the spatial resolution, the charge centroid cluster re… ▽ More Performance of triple GEM prototypes has been evaluated by means of a muon beam at the H4 line of the SPS test area at CERN. The data from two planar prototypes have been reconstructed and analyzed offline with two clusterization methods: the enter of gravity of the charge distribution and the micro Time Projection Chamber (\muTPC). Concerning the spatial resolution, the charge centroid cluster reconstruction performs extremely well with no magnetic field: the resolution is well below 100 \mum . Increasing the magnetic field intensity, the resolution degrades almost linearly as effect of the Lorentz force that displaces, broadens and asymmetrizes the electron avalanche. Tuning the electric fields of the GEM prototype we could achieve the unprecedented spatial resolution of 190 \mum at 1 Tesla. In order to boost the spatial resolution with strong magnetic field and inclined tracks a \muTPC cluster reconstruction has been investigated. Such a readout mode exploits the good time resolution of the GEM detector and electronics to reconstruct the trajectory of the particle inside the conversion gap. Beside the improvement of the spatial resolution, information on the track angle can be also extracted. The new clustering algorithm has been tested with diagonal tracks with no magnetic field showing a resolution between 100 um and 150 um for the incident angle ranging from 10° to 45° . Studies show similar performance with 1 Tesla magnetic field. This is the first use of a \muTPC readout with a triple GEM detector in magnetic field. This study has shown that a combined readout is capable to guarantee stable performance over a broad spectrum of particle momenta and incident angles, up to a 1 Tesla magnetic field. △ Less

Submitted 14 July, 2017; originally announced July 2017.

The Cylindrical GEM Inner Tracker of the BESIII experiment: prototype test beam results

Authors: L. Lavezzi, M. Alexeev, A. Amoroso, R. Baldini Ferroli, M. Bertani, D. Bettoni, F. Bianchi, A. Calcaterra, N. Canale, M. Capodiferro, V. Carassiti, S. Cerioni, JY. Chai, S. Chiozzi, G. Cibinetto, F. Cossio, A. Cotta Ramusino, F. De Mori, M. Destefanis, J. Dong, F. Evangelisti, R. Farinelli, L. Fava, G. Felici, E. Fioravanti , et al. (27 additional authors not shown)

Abstract: A cylindrical GEM detector is under development, to serve as an upgraded inner tracker at the BESIII spectrometer. It will consist of three layers of cylindrically-shaped triple GEMs surrounding the interaction point. The experiment is taking data at the e+e- collider BEPCII in Bei**g (China) and the GEM tracker will be installed in 2018. Tests on the performances of triple GEMs in strong magneti… ▽ More A cylindrical GEM detector is under development, to serve as an upgraded inner tracker at the BESIII spectrometer. It will consist of three layers of cylindrically-shaped triple GEMs surrounding the interaction point. The experiment is taking data at the e+e- collider BEPCII in Bei**g (China) and the GEM tracker will be installed in 2018. Tests on the performances of triple GEMs in strong magnetic field have been run by means of the muon beam available in the H4 line of SPS (CERN) with both planar chambers and the first cylindrical prototype. Efficiencies and resolutions have been evaluated using different gains, gas mixtures, with and without magnetic field. The obtained efficiency is 97-98% on single coordinate view, in many operational arrangements. The spatial resolution for planar GEMs has been evaluated with two different algorithms for the position determination: the charge centroid and the micro time projection chamber (mu-TPC) methods. The two modes are complementary and are able to cope with the asymmetry of the electron avalanche when running in magnetic field, and with non-orthogonal incident tracks. With the charge centroid, a resolution lower than 100 micron has been reached without magnetic field and lower than 200 micron with a magnetic field up to 1 T. The mu-TPC mode showed to be able to improve those results. In the first beam test with the cylindrical prototype, the detector had a very good stability under different voltage configurations and particle intensities. The resolution evaluation is in progress. △ Less

Submitted 3 July, 2017; v1 submitted 7 June, 2017; originally announced June 2017.

Comments: Proceedings for "Instrumentation for Colliding Beam Physics" (INSTR17) Conference, 27 February - 3 March 2017, Novosibirsk, Russia (prepared for submission to JINST)

A custom readout electronics for the BESIII CGEM detector

Authors: M. Da Rocha Rolo, M. Alexeev, A. Amoroso, R. Baldini Ferroli, M. Bertani, D. Bettoni, F. Bianchi, R. Bugalho, A. Calcaterra, N. Canale, M. Capodiferro, V. Carassiti, S. Cerioni, JY. Chai, S. Chiozzi, G. Cibinetto, F. Cossio, A. Cotta Ramusino, F. De Mori, M. Destefanis, A. Di Francesco, J. Dong, F. Evangelisti, R. Farinelli, L. Fava , et al. (31 additional authors not shown)

Abstract: For the upgrade of the inner tracker of the BESIII spectrometer, planned for 2018, a lightweight tracker based on an innovative Cylindrical Gas Electron Multiplier (CGEM) detector is now under development. The analogue readout of the CGEM enables the use of a charge centroid algorithm to improve the spatial resolution to better than 130 um while loosening the pitch strip to 650 um, which allows to… ▽ More For the upgrade of the inner tracker of the BESIII spectrometer, planned for 2018, a lightweight tracker based on an innovative Cylindrical Gas Electron Multiplier (CGEM) detector is now under development. The analogue readout of the CGEM enables the use of a charge centroid algorithm to improve the spatial resolution to better than 130 um while loosening the pitch strip to 650 um, which allows to reduce the total number of channels to about 10 000. The channels are readout by 160 dedicated integrated 64-channel front-end ASICs, providing a time and charge measurement and featuring a fully-digital output. The energy measurement is extracted either from the time-over-threshold (ToT) or the 10-bit digitisation of the peak amplitude of the signal. The time of the event is generated by quad-buffered low-power TDCs, allowing for rates in excess of 60 kHz per channel. The TDCs are based on analogue interpolation techniques and produce a time stamp (or two, if working in ToT mode) of the event with a time resolution better than 50 ps. The front-end noise, based on a CSA and CR-RC2 shapers, dominate the channel intrinsic time jitter, which is less than 5 ns r.m.s.. The time information of the hit can be used to reconstruct the track path, operating the detector as a small TPC and hence improving the position resolution when the distribution of the cloud, due to large incident angle or magnetic field, is very broad. Event data is collected by an off-detector motherboard, where each GEM-ROC readout card handles 4 ASIC carrier PCBs (512 channels). Configuration upload and data readout between the off-detector electronics and the VME-based data collector cards are managed by bi-directional fibre optical links. △ Less

Submitted 28 June, 2017; v1 submitted 7 June, 2017; originally announced June 2017.

Comments: Proceedings for "Instrumentation for Colliding Beam Physics" (INSTR17) conference, 27 February - 3 March 2017, Novosibirsk, Russia. Updated version with minor corrections suggested by reviewers, to be published by JINST

Luminosity measurements for the R scan experiment at BESIII

Authors: M. Ablikim, M. N. Achasov, S. Ahmed, X. C. Ai, O. Albayrak, M. Albrecht, D. J. Ambrose, A. Amoroso, F. F. An, Q. An, J. Z. Bai, O. Bakina, R. Baldini Ferroli, Y. Ban, D. W. Bennett, J. V. Bennett, N. Berger, M. Bertani, D. Bettoni, J. M. Bian, F. Bianchi, E. Boger, I. Boyko, R. A. Briere, H. Cai , et al. (405 additional authors not shown)

Abstract: By analyzing the large-angle Bhabha scattering events $e^{+}e^{-}$ $\to$ ($γ$)$e^{+}e^{-}$ and diphoton events $e^{+}e^{-}$ $\to$ $γγ$ for the data sets collected at center-of-mass (c.m.) energies between 2.2324 and 4.5900 GeV (131 energy points in total) with the upgraded Bei**g Spectrometer (BESIII) at the Bei**g Electron-Positron Collider (BEPCII), the integrated luminosities have been measur… ▽ More By analyzing the large-angle Bhabha scattering events $e^{+}e^{-}$ $\to$ ($γ$)$e^{+}e^{-}$ and diphoton events $e^{+}e^{-}$ $\to$ $γγ$ for the data sets collected at center-of-mass (c.m.) energies between 2.2324 and 4.5900 GeV (131 energy points in total) with the upgraded Bei**g Spectrometer (BESIII) at the Bei**g Electron-Positron Collider (BEPCII), the integrated luminosities have been measured at the different c.m. energies, individually. The results are the important inputs for R value and $J/ψ$ resonance parameter measurements. △ Less

Submitted 11 February, 2017; originally announced February 2017.

Feasibility study for the measurement of $πN$ TDAs at PANDA in $\bar{p}p\to J/ψπ^0$

Authors: PANDA Collaboration, B. Singh, W. Erni, B. Krusche, M. Steinacher, N. Walford, H. Liu, Z. Liu, B. Liu, X. Shen, C. Wang, J. Zhao, M. Albrecht, T. Erlen, M. Fink, F. H. Heinsius, T. Held, T. Holtmann, S. Jasper, I. Keshk, H. Koch, B. Kopf, M. Kuhlmann, M. Kümmel, S. Leiber , et al. (488 additional authors not shown)

Abstract: The exclusive charmonium production process in $\bar{p}p$ annihilation with an associated $π^0$ meson $\bar{p}p\to J/ψπ^0$ is studied in the framework of QCD collinear factorization. The feasibility of measuring this reaction through the $J/ψ\to e^+e^-$ decay channel with the PANDA (AntiProton ANnihilation at DArmstadt) experiment is investigated. Simulations on signal reconstruction efficiency as… ▽ More The exclusive charmonium production process in $\bar{p}p$ annihilation with an associated $π^0$ meson $\bar{p}p\to J/ψπ^0$ is studied in the framework of QCD collinear factorization. The feasibility of measuring this reaction through the $J/ψ\to e^+e^-$ decay channel with the PANDA (AntiProton ANnihilation at DArmstadt) experiment is investigated. Simulations on signal reconstruction efficiency as well as the background rejection from various sources including the $\bar{p}p\toπ^+π^-π^0$ and $\bar{p}p\to J/ψπ^0π^0$ reactions are performed with PandaRoot, the simulation and analysis software framework of the PANDA experiment. It is shown that the measurement can be done at PANDA with significant constraining power under the assumption of an integrated luminosity attainable in four to five months of data taking at the maximum design luminosity. △ Less

Submitted 7 October, 2016; originally announced October 2016.

Comments: 25 pages, 22 figures

Journal ref: Phys. Rev. D 95, 032003 (2017)

The Straw Tube Trackers of the PANDA Experiment

Authors: P. Gianotti, V. Lucherini, E. Pace, G. L. Boca, S. Costanza, P. Genova, L. Lavezzi, P. Montanga, A. Rotondi, M. Bragadireanu, M. E. Vasile, D. Pietreanu, J. Biernat, S. Jowzaee, G. Korcyl, M. Palka, P. Salabura, J. Smyrski, T. Fiutowski, M. Idzik, D. Przyborowski, K. Korcyl, P. Kulessa, K. Pysz, S. Dobbs , et al. (13 additional authors not shown)

Abstract: The PANDA experiment will be built at the FAIR facility at Darmstadt (Germany) to perform accurate tests of the strong interaction through bar pp and bar pA annihilation's studies. To track charged particles, two systems consisting of a set of planar, closed-packed, self-supporting straw tube layers are under construction. The PANDA straw tubes will have also unique characteristics in term of mate… ▽ More The PANDA experiment will be built at the FAIR facility at Darmstadt (Germany) to perform accurate tests of the strong interaction through bar pp and bar pA annihilation's studies. To track charged particles, two systems consisting of a set of planar, closed-packed, self-supporting straw tube layers are under construction. The PANDA straw tubes will have also unique characteristics in term of material budget and performance. They consist of very thin mylar-aluminized cathodes which are made self-supporting by means of the operation gas-mixture over-pressure. This solution allows to reduce at maximum the weight of the mechanical support frame and hence the detector material budget. The PANDA straw tube central tracker will not only reconstruct charged particle trajectories, but also will help in low momentum (< 1 GeV) particle identification via dE/dx measurements. This is a quite new approach that PANDA tracking group has first tested with detailed Monte Carlo simulations, and then with experimental tests of detector prototypes. This paper addresses the design issues of the PANDA straw tube trackers and the performance obtained in prototype tests. △ Less

Submitted 17 July, 2013; originally announced July 2013.

Comments: 7 pages,16 figures

Journal ref: IEEE Xplore publication 2013

Design Studies of the PWO Forward End-cap Calorimeter for PANDA

Authors: Hossein Moeini, Mohammad Al-Turany, Mohammad Babai, Alexandra Biegun, Olga Bondarenko, Klaus Gotzen, Myroslav Kavatsyuk, Michel Lindemulder, Herbert Lohner, Dima Melnychuk, Johan Messchendorp, Henk Smit, Stefano Spataro, Rick Veenstra

Abstract: The PANDA detection system at FAIR, Germany, is designed to study antiproton-proton annihilations, in order to investigate among others the realm of charm-meson states and glueballs, which has still much to reveal. The yet unknown properties of this field are to be unraveled through studying QCD phenomena in the non-perturbative regime. The multipurpose PANDA detector will be capable of tracking,… ▽ More The PANDA detection system at FAIR, Germany, is designed to study antiproton-proton annihilations, in order to investigate among others the realm of charm-meson states and glueballs, which has still much to reveal. The yet unknown properties of this field are to be unraveled through studying QCD phenomena in the non-perturbative regime. The multipurpose PANDA detector will be capable of tracking, calorimetry, and particle identification, and is foreseen to run at high luminosities providing average reaction rates up to 20 Million interactions/s. The envisaged physics program requires measurements of photons and charged particles with excellent energy, position, and time resolutions. The electromagnetic calorimeter (EMC) will serve as one of the basic components of the detector setup and comprises cooled Lead-Tungstate (PbWO4) crystals. This paper presents the mechanical design of the Forward End-cap calorimeter and analyses the response of this detector component in conjunction with the full EMC and the complete PANDA detector. The simulation studies are focused on the performance of the planned EMC with respect to the energy and spatial resolution of the reconstructed photons. Results of the Monte Carlo simulations, excluding very low-energy photons, have been validated by data obtained from a prototype calorimeter and shown to fulfil the requirements imposed by the PANDA physics program. △ Less

Submitted 11 January, 2014; v1 submitted 12 June, 2013; originally announced June 2013.

Comments: 22 Pages, 24 Figures, 4 Tables

Journal ref: Eur. Phys. J. A (2013) 49: 138

Measurements of Baryon Pair Decays of $χ_{cJ}$ Mesons

Authors: M. Ablikim, M. N. Achasov, O. Albayrak, D. J. Ambrose, F. F. An, Q. An, J. Z. Bai, Y. Ban, J. Becker, J. V. Bennett, M. Bertani, J. M. Bian, E. Boger, O. Bondarenko, I. Boyko, R. A. Briere, V. Bytev, X. Cai, O. Cakir, A. Calcaterra, G. F. Cao, S. A. Cetin, J. F. Chang, G. Chelkov, G. Chen , et al. (326 additional authors not shown)

Abstract: Using 106 $\times 10^{6}$ $ψ^{\prime}$ decays collected with the BESIII detector at the BEPCII, three decays of $χ_{cJ}$ ($J=0,1,2$) with baryon pairs ($\llb$, $\ssb$, $\SSB$) in the final state have been studied. The branching fractions are measured to be $\cal{B}$$(χ_{c0,1,2}\rightarrowΛ\barΛ) =(33.3 \pm 2.0 \pm 2.6)\times 10^{-5}$, $(12.2 \pm 1.1 \pm 1.1)\times 10^{-5}$,… ▽ More Using 106 $\times 10^{6}$ $ψ^{\prime}$ decays collected with the BESIII detector at the BEPCII, three decays of $χ_{cJ}$ ($J=0,1,2$) with baryon pairs ($\llb$, $\ssb$, $\SSB$) in the final state have been studied. The branching fractions are measured to be $\cal{B}$$(χ_{c0,1,2}\rightarrowΛ\barΛ) =(33.3 \pm 2.0 \pm 2.6)\times 10^{-5}$, $(12.2 \pm 1.1 \pm 1.1)\times 10^{-5}$, $(20.8 \pm 1.6 \pm 2.3)\times 10^{-5}$; $\cal{B}$$(χ_{c0,1,2}\rightarrowΣ^{0}\barΣ^{0})$ = $(47.8 \pm 3.4 \pm 3.9)\times 10^{-5}$, $(3.8 \pm 1.0 \pm 0.5)\times 10^{-5}$, $(4.0 \pm 1.1 \pm 0.5) \times 10^{-5}$; and $\cal{B}$$(χ_{c0,1,2}\rightarrowΣ^{+}\barΣ^{-})$ = $(45.4 \pm 4.2 \pm 3.0)\times 10^{-5}$, $(5.4 \pm 1.5 \pm 0.5)\times 10^{-5}$, $(4.9 \pm 1.9 \pm 0.7)\times 10^{-5}$, where the first error is statistical and the second is systematic. Upper limits on the branching fractions for the decays of $χ_{c1,2}\rightarrowΣ^{0}\barΣ^{0}$, $Σ^{+}\barΣ^{-}$, are estimated to be $\cal{B}$$(χ_{c1}\rightarrowΣ^{0}\barΣ^{0}) < 6.2\times 10^{-5}$, $\cal{B}$$(χ_{c2}\rightarrowΣ^{0}\barΣ^{0}) < 6.5\times 10^{-5}$, $\cal{B}$$(χ_{c1}\rightarrowΣ^{+}\barΣ^{-}) < 8.7\times 10^{-5}$ and $\cal{B}$$(χ_{c2}\rightarrowΣ^{+}\barΣ^{-}) < 8.8\times 10^{-5}$ at the 90% confidence level. △ Less

Submitted 4 March, 2013; v1 submitted 9 November, 2012; originally announced November 2012.

Comments: 13 pages, 7 figures, 3 tables

Journal ref: Phys. Rev. D 87, 032007 (2013)

Technical Design Report for the: PANDA Micro Vertex Detector

Authors: PANDA Collaboration, W. Erni, I. Keshelashvili, B. Krusche, M. Steinacher, Y. Heng, Z. Liu, H. Liu, X. Shen, Q. Wang, H. Xu, M. Albrecht, J. Becker, K. Eickel, F. Feldbauer, M. Fink, P. Friedel, F. H. Heinsius, T. Held, H. Koch, B. Kopf, M. Leyhe, C. Motzko, M. Pelizäus, J. Pychy , et al. (436 additional authors not shown)

Abstract: This document illustrates the technical layout and the expected performance of the Micro Vertex Detector (MVD) of the PANDA experiment. The MVD will detect charged particles as close as possible to the interaction zone. Design criteria and the optimisation process as well as the technical solutions chosen are discussed and the results of this process are subjected to extensive Monte Carlo physics… ▽ More This document illustrates the technical layout and the expected performance of the Micro Vertex Detector (MVD) of the PANDA experiment. The MVD will detect charged particles as close as possible to the interaction zone. Design criteria and the optimisation process as well as the technical solutions chosen are discussed and the results of this process are subjected to extensive Monte Carlo physics studies. The route towards realisation of the detector is outlined. △ Less

Submitted 10 August, 2012; v1 submitted 27 July, 2012; originally announced July 2012.

Comments: 189 pages, 225 figures, 41 tables

Technical Design Report for the: PANDA Straw Tube Tracker

Authors: PANDA Collaboration, W. Erni, I. Keshelashvili, B. Krusche, M. Steinacher, Y. Heng, Z. Liu, H. Liu, X. Shen, Q. Wang, H. Xu, A. Aab, M. Albrecht, J. Becker, A. Csapó, F. Feldbauer, M. Fink, P. Friedel, F. H. Heinsius, T. Held, L. Klask, H. Koch, B. Kopf, S. Leiber, M. Leyhe , et al. (451 additional authors not shown)

Abstract: This document describes the technical layout and the expected performance of the Straw Tube Tracker (STT), the main tracking detector of the PANDA target spectrometer. The STT encloses a Micro-Vertex-Detector (MVD) for the inner tracking and is followed in beam direction by a set of GEM-stations. The tasks of the STT are the measurement of the particle momentum from the reconstructed trajectory an… ▽ More This document describes the technical layout and the expected performance of the Straw Tube Tracker (STT), the main tracking detector of the PANDA target spectrometer. The STT encloses a Micro-Vertex-Detector (MVD) for the inner tracking and is followed in beam direction by a set of GEM-stations. The tasks of the STT are the measurement of the particle momentum from the reconstructed trajectory and the measurement of the specific energy-loss for a particle identification. Dedicated simulations with full analysis studies of certain proton-antiproton reactions, identified as being benchmark tests for the whole PANDA scientific program, have been performed to test the STT layout and performance. The results are presented, and the time lines to construct the STT are described. △ Less

Submitted 4 June, 2012; v1 submitted 24 May, 2012; originally announced May 2012.

Comments: accepted for publication on EPJA

Journal ref: Eur. Phys. J. A (2013) 49: 25

Technical Design Report for the PANDA Solenoid and Dipole Spectrometer Magnets

Authors: The PANDA Collaboration, W. Erni, I. Keshelashvili, B. Krusche, M. Steinacher, Y. Heng, Z. Liu, H. Liu, X. Shen, O. Wang, H. Xu, J. Becker, F. Feldbauer, F. -H. Heinsius, T. Held, H. Koch, B. Kopf, M. Pelizaeus, T. Schroeder, M. Steinke, U. Wiedner, J. Zhong, A. Bianconi, M. Bragadireanu, D. Pantea , et al. (387 additional authors not shown)

Abstract: This document is the Technical Design Report covering the two large spectrometer magnets of the PANDA detector set-up. It shows the conceptual design of the magnets and their anticipated performance. It precedes the tender and procurement of the magnets and, hence, is subject to possible modifications arising during this process. This document is the Technical Design Report covering the two large spectrometer magnets of the PANDA detector set-up. It shows the conceptual design of the magnets and their anticipated performance. It precedes the tender and procurement of the magnets and, hence, is subject to possible modifications arising during this process. △ Less

Submitted 1 July, 2009; originally announced July 2009.

Comments: 10 pages, 14MB, accepted by FAIR STI in May 2009, editors: Inti Lehmann (chair), Andrea Bersani, Yuri Lobanov, Jost Luehning, Jerzy Smyrski, Technical Coordiantor: Lars Schmitt, Bernd Lewandowski (deputy), Spokespersons: Ulrich Wiedner, Paola Gianotti (deputy)

Technical Design Report for PANDA Electromagnetic Calorimeter (EMC)

Authors: PANDA Collaboration, W. Erni, I. Keshelashvili, B. Krusche, M. Steinacher, Y. Heng, Z. Liu, H. Liu, X. Shen, O. Wang, H. Xu, J. Becker, F. Feldbauer, F. -H. Heinsius, T. Held, H. Koch, B. Kopf, M. Pelizaeus, T. Schroeder, M. Steinke, U. Wiedner, J. Zhong, A. Bianconi, M. Bragadireanu, D. Pantea , et al. (387 additional authors not shown)

Abstract: This document presents the technical layout and the envisaged performance of the Electromagnetic Calorimeter (EMC) for the PANDA target spectrometer. The EMC has been designed to meet the physics goals of the PANDA experiment, which is being developed for the Facility for Antiproton and Ion Research (FAIR) at Darmstadt, Germany. The performance figures are based on extensive prototype tests and… ▽ More This document presents the technical layout and the envisaged performance of the Electromagnetic Calorimeter (EMC) for the PANDA target spectrometer. The EMC has been designed to meet the physics goals of the PANDA experiment, which is being developed for the Facility for Antiproton and Ion Research (FAIR) at Darmstadt, Germany. The performance figures are based on extensive prototype tests and radiation hardness studies. The document shows that the EMC is ready for construction up to the front-end electronics interface. △ Less

Submitted 7 October, 2008; originally announced October 2008.

Comments: 199 pages, submitted to FAIR STI on July 1st 2008, Editors: Fritz-Herbert Heinsius, Bertram Kopf, Bernd Lewandowski (Deputy Technical Coordinator), Herbert Löhner, Rainer Novotny (Project Coordinator), Klaus Peters, Philippe Rosier, Lars Schmitt (Technical Coordinator), Alexander Vasiliev; Spokespersons: Ulrich Wiedner, Paola Gianotti (deputy)