-
A Novel Diamond-like Carbon based photocathode for PICOSEC Micromegas detectors
Authors:
X. Wang,
R. Aleksan,
Y. Angelis,
J. Bortfeldt,
F. Brunbauer,
M. Brunoldi,
E. Chatzianagnostou,
J. Datta,
K. Degmelt,
G. Fanourakis,
D. Fiorina,
K. J. Floethner,
M. Gallinaro,
F. Garcia,
I. Giomataris,
K. Gnanvo,
F. J. Iguaz,
D. Janssens,
A. Kallitsopoulou,
M. Kovacic,
B. Kross,
P. Legou,
M. Lisowska,
J. Liu,
I. Maniatis
, et al. (26 additional authors not shown)
Abstract:
The PICOSEC Micromegas (MM) detector is a precise timing gaseous detector based on a MM detector operating in a two-stage amplification mode and a Cherenkov radiator. Prototypes equipped with cesium iodide (CsI) photocathodes have shown promising time resolutions as precise as 24 picoseconds (ps) for Minimum Ionizing Particles. However, due to the high hygroscopicity and susceptibility to ion bomb…
▽ More
The PICOSEC Micromegas (MM) detector is a precise timing gaseous detector based on a MM detector operating in a two-stage amplification mode and a Cherenkov radiator. Prototypes equipped with cesium iodide (CsI) photocathodes have shown promising time resolutions as precise as 24 picoseconds (ps) for Minimum Ionizing Particles. However, due to the high hygroscopicity and susceptibility to ion bombardment of the CsI photocathodes, alternative photocathode materials are needed to improve the robustness of PICOSEC MM. Diamond-like Carbon (DLC) film have been introduced as a novel robust photocathode material, which have shown promising results. A batch of DLC photocathodes with different thicknesses were produced and evaluated using ultraviolet light. The quantum efficiency measurements indicate that the optimized thickness of the DLC photocathode is approximately 3 nm. Furthermore, DLC photocathodes show good resistance to ion bombardment in aging test compared to the CsI photocathode. Finally, a PICOSEC MM prototype equipped with DLC photocathodes was tested in muon beams. A time resolution of around 42 ps with a detection efficiency of 97% for 150 GeV/c muons were obtained. These results indicate the great potential of DLC as a photocathode for the PICOSEC MM detector.
△ Less
Submitted 25 June, 2024; v1 submitted 12 June, 2024;
originally announced June 2024.
-
Charting a finite element, mechanical atlas of dermatologic wound closure
Authors:
Congzhou M Sha
Abstract:
Wound geometry and the mechanical properties of human skin govern the failure modes of partially healed or scarred tissue. Though dermatologists and surgeons develop an intuitive understanding of the mechanical characteristics of skin through clinical practice, finite element models of wounds can aid in formalizing intuition. In this work, we explore the effect of wound geometry and primary intent…
▽ More
Wound geometry and the mechanical properties of human skin govern the failure modes of partially healed or scarred tissue. Though dermatologists and surgeons develop an intuitive understanding of the mechanical characteristics of skin through clinical practice, finite element models of wounds can aid in formalizing intuition. In this work, we explore the effect of wound geometry and primary intention closure on the propagation of mechanical stresses through skin. We use a two-layer, orthotropic, hyperelastic model of the epidermis, dermis, and subcutis to accurately capture the mechanical and geometric effects at work. We highlight the key assumptions which must be made when modeling closure of wounds by primary intention, clearly delineating promising areas for model improvement. Models are implemented in DOLFINx, an open-source finite element framework, and reference code is provided for reproducible and extensible science.
△ Less
Submitted 11 June, 2024;
originally announced June 2024.
-
Extraction of Weak Surface Diaphragmatic Electromyogram Using Modified Progressive FastICA Peel-Off
Authors:
Yao Li,
Dongsheng Zhao,
Haowen Zhao,
Xu Zhang,
Min Shao
Abstract:
Diaphragmatic electromyogram (EMGdi) contains crucial information about human respiration therefore can be used to monitor respiratory condition. Although it is practical to record EMGdi noninvasively and conveniently by placing surface electrodes over chest skin, extraction of such weak surface EMGdi (sEMGdi) from great noisy environment is a challenging task, limiting its clinical use compared w…
▽ More
Diaphragmatic electromyogram (EMGdi) contains crucial information about human respiration therefore can be used to monitor respiratory condition. Although it is practical to record EMGdi noninvasively and conveniently by placing surface electrodes over chest skin, extraction of such weak surface EMGdi (sEMGdi) from great noisy environment is a challenging task, limiting its clinical use compared with esophageal EMGdi. In this paper, a novel method is presented for extracting weak sEMGdi signal from high-noise environment based on fast independent component analysis (FastICA), constrained FastICA and a peel-off strategy. It is truly a modified version of of progressive FastICA peel-off (PFP) framework, where the constrained FastICA helps to extract and refine respiration-related sEMGdi signals, while the peel-off strategy ensures the complete extraction of weaker sEMGdi components. The method was validated using both synthetic and clinical signals. It was demonstrated that our method was able to extract clean sEMGdi signals efficiently with little distortion. It outperformed state-of-the-art comparison methods in terms of sufficiently high SIR and CORR at all noise levels when tested on synthetic data, while also achieved an accuracy of 95.06% and a F2-score of 96.73% for breath identification on clinical data. The study presents a valuable solution for noninvasive extraction of sEMGdi signals, providing a convenient and valuable way of ventilator synchrony with a significant potential in aiding respiratory rehabilitation and health.
△ Less
Submitted 28 June, 2024; v1 submitted 3 June, 2024;
originally announced June 2024.
-
Characterisation of resistive MPGDs with 2D readout
Authors:
L. Scharenberg,
F. Brunbauer,
H. Danielson,
Z. Fang,
K. J. Flöthner,
F. Garcia,
D. Janssens,
M. Lisowska,
J. Liu,
Y. Lyu,
B. Mehl,
H. Muller,
R. de Oliveira,
E. Oliveri,
G. Orlandini,
D. Pfeiffer,
O. Pizzirusso,
L. Ropelewski,
J. Samarati,
M. Shao,
A. Teixeira,
M. Van Stenis,
R. Veenhof,
Z. Zhang,
Y. Zhou
Abstract:
Micro-Pattern Gaseous Detectors (MPGDs) with resistive anode planes provide intrinsic discharge robustness while maintaining good spatial and time resolutions. Typically read out with 1D strips or pad structures, here the characterisation results of resistive anode plane MPGDs with 2D strip readout are presented. A uRWELL prototype is investigated in view of its use as a reference tracking detecto…
▽ More
Micro-Pattern Gaseous Detectors (MPGDs) with resistive anode planes provide intrinsic discharge robustness while maintaining good spatial and time resolutions. Typically read out with 1D strips or pad structures, here the characterisation results of resistive anode plane MPGDs with 2D strip readout are presented. A uRWELL prototype is investigated in view of its use as a reference tracking detector in a future gaseous beam telescope. A MicroMegas prototype with a fine-pitch mesh (730 line-pairs-per-inch) is investigated, both for comparison and to profit from the better field uniformity and thus the ability to operate the detector more stable at high gains. Furthermore, the measurements are another application of the RD51 VMM3a/SRS electronics.
△ Less
Submitted 6 February, 2024;
originally announced February 2024.
-
Pupil-driven quantitative differential phase contrast imaging
Authors:
Shuhe Zhang,
Hao Wu,
Tao Peng,
Zeyu Ke,
Meng Shao,
Tos T. J. M. Berendschot,
**hua Zhou
Abstract:
In this research, we reveal the inborn but hitherto ignored properties of quantitative differential phase contrast (qDPC) imaging: the phase transfer function being an edge detection filter. Inspired by this, we highlighted the duality of qDPC between optics and pattern recognition, and propose a simple and effective qDPC reconstruction algorithm, termed Pupil-Driven qDPC (pd-qDPC), to facilitate…
▽ More
In this research, we reveal the inborn but hitherto ignored properties of quantitative differential phase contrast (qDPC) imaging: the phase transfer function being an edge detection filter. Inspired by this, we highlighted the duality of qDPC between optics and pattern recognition, and propose a simple and effective qDPC reconstruction algorithm, termed Pupil-Driven qDPC (pd-qDPC), to facilitate the phase reconstruction quality for the family of qDPC-based phase reconstruction algorithms. We formed a new cost function in which modified L0-norm was used to represent the pupil-driven edge sparsity, and the qDPC convolution operator is duplicated in the data fidelity term to achieve automatic background removal. Further, we developed the iterative reweighted soft-threshold algorithms based on split Bregman method to solve this modified L0-norm problem. We tested pd-qDPC on both simulated and experimental data and compare against state-of-the-art (SOTA) methods including L2-norm, total variation regularization (TV-qDPC), isotropic-qDPC, and Retinex qDPC algorithms. Results show that our proposed model is superior in terms of phase reconstruction quality and implementation efficiency, in which it significantly increases the experimental robustness while maintaining the data fidelity. In general, the pd-qDPC enables the high-quality qDPC reconstruction without any modification of the optical system. It simplifies the system complexity and benefits the qDPC community and beyond including but not limited to cell segmentation and PTF learning based on the edge filtering property.
△ Less
Submitted 29 June, 2023;
originally announced June 2023.
-
A large area, high counting rate micromegas-based neutron detector for BNCT
Authors:
Zhujun Fang,
Zhiyong Zhang,
Bin Shi,
Wei Jiang,
Xianke Liu,
Siqi He,
Jun Chen,
** Cao,
Jianbei Liu,
Yi Zhou,
Ming Shao,
Botian Qu,
Shufeng Zhang,
Qian Wang
Abstract:
Beam monitoring and evaluation are very important to boron neutron capture therapy (BNCT), and a variety of detectors have been developed for these applications. However, most of the detectors used in BNCT only have a small detection area, leading to the inconvenience of the full-scale 2-D measurement of the beam. Based on micromegas technology, we designed a neutron detector with large detection…
▽ More
Beam monitoring and evaluation are very important to boron neutron capture therapy (BNCT), and a variety of detectors have been developed for these applications. However, most of the detectors used in BNCT only have a small detection area, leading to the inconvenience of the full-scale 2-D measurement of the beam. Based on micromegas technology, we designed a neutron detector with large detection area and high counting rate. This detector has a detection area of 288 mm multiples 288 mm and can measure thermal, epithermal, and fast neutrons with different detector settings. The BNCT experiments demonstrated that this detector has a very good 2-D imaging performance for the thermal, epithermal, fast neutron and gamma components, a highest counting rate of 94 kHz/channel, and a good linearity response to the beam power. Additionally, the flux fraction of each component can be calculated based on the measurement results. The Am-Be neutron source experiment indicates that this detector has a spatial resolution of approximately 1.4 mm, meeting the requirements of applications in BNCT. It is evident that this micromegas-based neutron detector with a large area and high counting rate capability has great development prospects in BNCT beam monitoring and evaluation applications.
△ Less
Submitted 29 April, 2023; v1 submitted 7 April, 2023;
originally announced April 2023.
-
Design and performance testing of a T0 detector for the CSR External-target Experiment
Authors:
D. Hu,
X. Wang,
M. Shao,
Y. Zhou,
S. Ye,
L. Zhao,
Y. Sun,
J. Lu,
H. Xu
Abstract:
The Cooling Storage Ring (CSR) External-target Experiment (CEE) at the Heavy Ion Research Facility in Lanzhou (HIRFL), China, is the first multi-purpose nuclear physics experimental device to operate in the Giga electron-volt (GeV) energy range. The primary goals of the CEE are to study the bulk properties of dense matter and to understand the quantum chromo-dynamic (QCD) phase diagram by measurin…
▽ More
The Cooling Storage Ring (CSR) External-target Experiment (CEE) at the Heavy Ion Research Facility in Lanzhou (HIRFL), China, is the first multi-purpose nuclear physics experimental device to operate in the Giga electron-volt (GeV) energy range. The primary goals of the CEE are to study the bulk properties of dense matter and to understand the quantum chromo-dynamic (QCD) phase diagram by measuring the charged particles produced in heavy-ion collisions in the target region with a large acceptance. The CEE is a spectrometer that focuses on charged final-state particle measurements running on the HIRFL-CSR. The time-of-flight (TOF) system is critical for identifying charged particles in the GeV energy region. In the CEE spectrometer, the TOF system consists of three parts: T0, internal TOF, and external TOF, which are used for the final-state particle identification. The T0 detector provides a high-precision start time for the TOF system by measuring the crossing time of the heavy ion beam. This study details the design, performance simulation, and performance testing of the T0 detector. The simulation results and heavy-ion beam test show that the T0 detector prototype has an excellent time resolution, which is better than 30 ps, and fulfills the requirements of the CEE.
△ Less
Submitted 6 April, 2023;
originally announced April 2023.
-
STCF Conceptual Design Report: Volume 1 -- Physics & Detector
Authors:
M. Achasov,
X. C. Ai,
R. Aliberti,
L. P. An,
Q. An,
X. Z. Bai,
Y. Bai,
O. Bakina,
A. Barnyakov,
V. Blinov,
V. Bobrovnikov,
D. Bodrov,
A. Bogomyagkov,
A. Bondar,
I. Boyko,
Z. H. Bu,
F. M. Cai,
H. Cai,
J. J. Cao,
Q. H. Cao,
Z. Cao,
Q. Chang,
K. T. Chao,
D. Y. Chen,
H. Chen
, et al. (413 additional authors not shown)
Abstract:
The Super $τ$-Charm facility (STCF) is an electron-positron collider proposed by the Chinese particle physics community. It is designed to operate in a center-of-mass energy range from 2 to 7 GeV with a peak luminosity of $0.5\times 10^{35}{\rm cm}^{-2}{\rm s}^{-1}$ or higher. The STCF will produce a data sample about a factor of 100 larger than that by the present $τ$-Charm factory -- the BEPCII,…
▽ More
The Super $τ$-Charm facility (STCF) is an electron-positron collider proposed by the Chinese particle physics community. It is designed to operate in a center-of-mass energy range from 2 to 7 GeV with a peak luminosity of $0.5\times 10^{35}{\rm cm}^{-2}{\rm s}^{-1}$ or higher. The STCF will produce a data sample about a factor of 100 larger than that by the present $τ$-Charm factory -- the BEPCII, providing a unique platform for exploring the asymmetry of matter-antimatter (charge-parity violation), in-depth studies of the internal structure of hadrons and the nature of non-perturbative strong interactions, as well as searching for exotic hadrons and physics beyond the Standard Model. The STCF project in China is under development with an extensive R\&D program. This document presents the physics opportunities at the STCF, describes conceptual designs of the STCF detector system, and discusses future plans for detector R\&D and physics case studies.
△ Less
Submitted 5 October, 2023; v1 submitted 28 March, 2023;
originally announced March 2023.
-
Landauer-QFLPS model for mixed Schottky-Ohmic contact two-dimensional transistors
Authors:
Zhao-Yi Yan,
Zhan Hou,
Kan-Hao Xue,
Tian Lu,
Ruiting Zhao,
Junying Xue,
Fan Wu,
Minghao Shao,
Jianlan Yan,
Anzhi Yan,
Zhenze Wang,
Penghui Shen,
Mingyue Zhao,
Xiangshui Miao,
Zhaoyang Lin,
Houfang Liu,
He Tian,
Yi Yang,
Tian-Ling Ren
Abstract:
Two-dimensional material-based field effect transistors (2DM-FETs) are playing a revolutionary role in electronic devices. However, after years of development, no device model can match the Pao-Sah model for standard silicon-based transistors in terms of physical accuracy and computational efficiency to support large-scale integrated circuit design. One remaining critical obstacle is the contacts…
▽ More
Two-dimensional material-based field effect transistors (2DM-FETs) are playing a revolutionary role in electronic devices. However, after years of development, no device model can match the Pao-Sah model for standard silicon-based transistors in terms of physical accuracy and computational efficiency to support large-scale integrated circuit design. One remaining critical obstacle is the contacts of 2DM-FETs. In order to self-consistently include the contact effect in the current model, it is necessary to perform self-consistent calculations, which is a fatal flaw for applications that prioritize efficiency. Here, we report that the Landauer-QFLPS model effectively overcomes the above contradiction, where QFLPS means quasi-Fermi-level phase space theory. By connecting the physical pictures of the contact and the intrinsic channel part, we have successfully derived a drain-source current formula including the contact effect. To verify the model, we prepared transistors based on two typical 2DMs, black phosphorus (BP) and molybdenum disulfide (MoS2), the former having ambipolar transport and the latter showing electron-dominant unipolar transport. The proposed new formula could describe both 2DM-FETs with Schottky or Ohmic contacts. Moreover, compared with traditional methods, the proposed model has the advantages of accuracy and efficiency, especially in describing non-monotonic drain conductance characteristics, because the contact effect is self-consistently and compactly packaged as an exponential term. More importantly, we also examined the model at the circuit level. Here, we fabricated a three-bit threshold inverter quantizer circuit based on ambipolar-BP process and experimentally demonstrated that the model can accurately predict the circuit performance. This industry-benign 2DM-FET model is supposed to be very useful for the development of 2DM-FET-based integrated circuits.
△ Less
Submitted 20 March, 2023;
originally announced March 2023.
-
A novel fast response and radiation-resistant scintillator detector for beam loss monitor
Authors:
Yuan**g Ji,
Zebo Tang,
Chen Li,
Xin Li,
Ming Shao
Abstract:
At high luminosity areas, beam loss monitor with fast response and high radiation resistance is crucial for accelerator operation. In this article, we report the design and test results of a fast response and radiation-resistant scintillator detector as the beam loss monitor for high luminosity colliders, especially at low energy regions such as RFQ. The detector consists of a 2 cm*2 cm 0.5 cm LYS…
▽ More
At high luminosity areas, beam loss monitor with fast response and high radiation resistance is crucial for accelerator operation. In this article, we report the design and test results of a fast response and radiation-resistant scintillator detector as the beam loss monitor for high luminosity colliders, especially at low energy regions such as RFQ. The detector consists of a 2 cm*2 cm 0.5 cm LYSO crystal readout by a 6 mm*6 mm Silicon photomultiplier. Test results from various radioactive sources show that the detector has good sensitivity to photons from tens of keV to several MeV with good linearity and energy resolution (23% for 60 keV γ-ray). For the field test, two such detectors are installed outside of the vacuum chamber shell of an 800 MeV electron storage ring. The details of the test and results are introduced.
△ Less
Submitted 21 February, 2023;
originally announced February 2023.
-
Differentiable Rotamer Sampling with Molecular Force Fields
Authors:
Congzhou M. Sha,
Jian Wang,
Nikolay V. Dokholyan
Abstract:
Molecular dynamics is the primary computational method by which modern structural biology explores macromolecule structure and function. Boltzmann generators have been proposed as an alternative to molecular dynamics, by replacing the integration of molecular systems over time with the training of generative neural networks. This neural network approach to MD samples rare events at a higher rate t…
▽ More
Molecular dynamics is the primary computational method by which modern structural biology explores macromolecule structure and function. Boltzmann generators have been proposed as an alternative to molecular dynamics, by replacing the integration of molecular systems over time with the training of generative neural networks. This neural network approach to MD samples rare events at a higher rate than traditional MD, however critical gaps in the theory and computational feasibility of Boltzmann generators significantly reduce their usability. Here, we develop a mathematical foundation to overcome these barriers; we demonstrate that the Boltzmann generator approach is sufficiently rapid to replace traditional MD for complex macromolecules, such as proteins in specific applications, and we provide a comprehensive toolkit for the exploration of molecular energy landscapes with neural networks.
△ Less
Submitted 22 February, 2023;
originally announced February 2023.
-
R & D of prototype iTOF-MRPC at CEE
Authors:
Y. Zhou,
D. Hu,
X. Wang,
M. Shao,
L. Zhao,
Y. Sun,
J. Lu,
H. Xua
Abstract:
The cooling storage ring (CSR) external-target experiment (CEE) is a spectrometer running at the Heavy Ion Research Facility (HIRFL) at Lanzhou. The CEE is the first large-scale nuclear physics experimental device by China to operate in the fixed-target mode with an energy of 1 GeV. The purpose of the CEE is to study the properties of dense nuclear matter. CEE uses a multi-gap resistive plate cham…
▽ More
The cooling storage ring (CSR) external-target experiment (CEE) is a spectrometer running at the Heavy Ion Research Facility (HIRFL) at Lanzhou. The CEE is the first large-scale nuclear physics experimental device by China to operate in the fixed-target mode with an energy of 1 GeV. The purpose of the CEE is to study the properties of dense nuclear matter. CEE uses a multi-gap resistive plate chamber (MRPC) as its internal time-of-flight (iTOF) detector for the identification of final-state particles. An iTOF-MRPC prototype with 24 gaps was designed to meet the requirements of CEE, and the readout electronics of the prototype use the FPGA-based time digitization technology. Using cosmic ray tests, the time resolution of the iTOF prototype was found to be approximately 30 ps. In order to further understand how to improve the time resolution of MRPC, ANSYS HFSS was used to simulate the signal transmission process in MRPC. The main factors affecting the timing performance of the MRPC and, accordingly, the optimization scheme are presented.
△ Less
Submitted 25 February, 2023; v1 submitted 23 November, 2022;
originally announced November 2022.
-
High-fidelity quantitative differential phase contrast deconvolution using dark-field sparse prior
Authors:
Shuhe Zhang,
Tao Peng,
Zeyu Ke,
Meng Shao,
Tos T. J. M. Berendschot,
**hua Zhou
Abstract:
Differential phase contrast (DPC) imaging plays an important role in the family of quantitative phase measurement. However, the reconstruction algorithm for quantitative DPC (qDPC) imaging is not yet optimized, as it does not incorporate the inborn properties of qDPC imaging. In this research, we propose a simple but effective image prior, the dark-field sparse prior (DSP), to facilitate the phase…
▽ More
Differential phase contrast (DPC) imaging plays an important role in the family of quantitative phase measurement. However, the reconstruction algorithm for quantitative DPC (qDPC) imaging is not yet optimized, as it does not incorporate the inborn properties of qDPC imaging. In this research, we propose a simple but effective image prior, the dark-field sparse prior (DSP), to facilitate the phase reconstruction quality for all DPC-based phase reconstruction algorithms. The DSP is based on the key observation that most pixel values for an idea differential phase contrast image are zeros since the subtraction of two images under anti-symmetric illumination cancels all background components. With this DSP prior, we formed a new cost function in which L0-norm was used to represent the DSP. Further, we developed two different algorithms based on (1) the Half Quadratic Splitting, and (2) the Richardson-Lucy deconvolution to solve this NP-hard L0-norm problem. We tested our new model on both simulated and experimental data and compare against state-of-the-art methods including L2-norm and total variation regularizations. Results show that our proposed model is superior in terms of phase reconstruction quality and implementation efficiency, in which it significantly increases the experimental robustness, while maintaining the data fidelity.
△ Less
Submitted 15 June, 2022;
originally announced June 2022.
-
Study of Hybrid MicroPattern Gas Detector with CsI Photocathode For Super Tau-Charm Factory RICH
Authors:
** Li,
Qian Liu,
Jianbei Liu,
Ming Shao,
Zhiyong Zhang,
Jianxin Feng,
Anqi Wang,
Baolin Hou,
Lei Zhao,
Hongbang Liu
Abstract:
Super tau-Charm facility(STCF) is a future electron-position collider operating at tau-Charm energy region aimed to study hadron structure and spectroscopy. The baseline design of the STCF barrel particle identification(PID) detector in the momentum range up to 2 GeV/c is provided by a Ring Imaging Cherenkov Counter(RICH). The architecture of the RICH is an approximately focusing design with liqui…
▽ More
Super tau-Charm facility(STCF) is a future electron-position collider operating at tau-Charm energy region aimed to study hadron structure and spectroscopy. The baseline design of the STCF barrel particle identification(PID) detector in the momentum range up to 2 GeV/c is provided by a Ring Imaging Cherenkov Counter(RICH). The architecture of the RICH is an approximately focusing design with liquid perfluorohexane sealed in the quartz container as radiator and a hybrid combination of a CsI coated layers of THGEMs and a Micromegas as the photo-electron detector. A 16*16 cm^2 prototype with quartz radiator has been built and tested at DESY. It was stably operated with 10^5 effective gain. In this paper, the design, the performance, the reconstruction algorithm and the systematic error for single photon electron angular resolution in the aspect of RICH detectors are discusses.
△ Less
Submitted 3 November, 2022; v1 submitted 3 May, 2022;
originally announced May 2022.
-
CEE inner TOF prototype design and preliminary test results
Authors:
X Wang,
D Hu,
M Shao,
L Zhao,
Y Sun,
J Lu,
H Xu,
Y Zhou
Abstract:
The Cooling Storage Ring (CSR) External-target Experiment(CEE) is the first multi-purpose nuclear physics experimental device to operate in the GeV energy range at the Heavy-Ion Research Facility(HIRFL-CSR) in Lanzhou, China. The primary goals of the CEE are to study the bulk properties of dense matter and to understand the quantum chromo-dynamic (QCD) phase diagram by measuring the charged partic…
▽ More
The Cooling Storage Ring (CSR) External-target Experiment(CEE) is the first multi-purpose nuclear physics experimental device to operate in the GeV energy range at the Heavy-Ion Research Facility(HIRFL-CSR) in Lanzhou, China. The primary goals of the CEE are to study the bulk properties of dense matter and to understand the quantum chromo-dynamic (QCD) phase diagram by measuring the charged particles produced in heavy-ion collisions at the target region with a large acceptance. An inner time of flight (iTOF) system has been proposed to measure the multiplicity, angular distribution, and time information of the charged particles. Herein, we introduce the performance requirements of iTOF according to calculations and GEANT4 simulations. The proposed system is characterized by high granularity and time performance, hence, the conceptual design of the iTOF wall adopts high granularity Multi-gap Resistive Plate Chambers (MRPC) with a time resolution of around 30 ps. To evaluate the MRPC design, the cosmic ray test was performed. A timing resolution better than 28 ps and an efficiency better than 98% has been achieved for MIPs, as interpreted by the cosmic ray GEANT4 simulation of time jitter components.
△ Less
Submitted 25 March, 2022;
originally announced March 2022.
-
Snowmass 2021 White Paper Instrumentation Frontier 05 -- White Paper 1: MPGDs: Recent advances and current R&D
Authors:
K. Dehmelt,
M. Della Pietra,
H. Muller,
S. E. Tzamarias,
A. White,
S. White,
Z. Zhang,
M. Alviggi,
I. Angelis,
S. Aune,
J. Bortfeldt,
M. Bregant,
F. Brunbauer,
M. T. Camerlingo,
V. Canale,
V. D'Amico,
D. Desforge,
C. Di Donato,
R. Di Nardo,
G. Fanourakis,
K. J. Floethner,
M. Gallinaro,
F. Garcia,
I. Giomataris,
K. Gnanvo
, et al. (45 additional authors not shown)
Abstract:
This paper will review the origins, development, and examples of new versions of Micro-Pattern Gas Detectors. The goal for MPGD development was the creation of detectors that could cost-effectively cover large areas while offering excellent position and timing resolution, and the ability to operate at high incident particle rates. The early MPGD developments culminated in the formation of the RD51…
▽ More
This paper will review the origins, development, and examples of new versions of Micro-Pattern Gas Detectors. The goal for MPGD development was the creation of detectors that could cost-effectively cover large areas while offering excellent position and timing resolution, and the ability to operate at high incident particle rates. The early MPGD developments culminated in the formation of the RD51 collaboration which has become the critical organization for the promotion of MPGDs and all aspects of their production, characterization, simulation, and uses in an expanding array of experimental configurations. For the Snowmass 2021 study, a number of Letters of Interest were received that illustrate ongoing developments and expansion of the use of MPGDs. In this paper, we highlight high precision timing, high rate application, trigger capability expansion of the SRS readout system, and a structure designed for low ion backflow.
△ Less
Submitted 19 March, 2022; v1 submitted 12 March, 2022;
originally announced March 2022.
-
Electrochemical control of ferroelectricity in hafnia-based ferroelectric devices using reversible oxygen migration
Authors:
M. H. Shao,
H. F. Liu,
R. He,
X. M. Li,
L. Wu,
J. Ma,
X. C. Hu,
R. T. Zhao,
Z. C. Zhong,
Y. Yu,
C. H. Wan,
Y. Yang,
C. -W. Nan,
X. D. Bai,
T. -L. Ren,
X. Renshaw Wang
Abstract:
Ferroelectricity, especially in hafnia-based thin films at nanosizes, has been rejuvenated in the fields of low-power, nonvolatile and Si-compatible modern memory and logic applications. Despite tremendous efforts to explore the formation of the metastable ferroelectric phase and the polarization degradation during field cycling, the ability of oxygen vacancy to exactly engineer and switch polariz…
▽ More
Ferroelectricity, especially in hafnia-based thin films at nanosizes, has been rejuvenated in the fields of low-power, nonvolatile and Si-compatible modern memory and logic applications. Despite tremendous efforts to explore the formation of the metastable ferroelectric phase and the polarization degradation during field cycling, the ability of oxygen vacancy to exactly engineer and switch polarization remains to be elucidated. Here we report reversibly electrochemical control of ferroelectricity in Hf$_{0.5}$Zr$_{0.5}$O$_2$ (HZO) heterostructures with a mixed ionic-electronic LaSrMnO$_3$ electrode, achieving a hard breakdown field more than 18 MV/cm, over fourfold as high as that of typical HZO. The electrical extraction and insertion of oxygen into HZO is macroscopically characterized and atomically imaged in situ. Utilizing this reversible process, we achieved multiple polarization states and even repeatedly repaired the damaged ferroelectricity by reversed negative electric fields. Our study demonstrates the robust and switchable ferroelectricity in hafnia oxide distinctly associated with oxygen vacancy and opens up opportunities to recover, manipulate, and utilize rich ferroelectric functionalities for advanced ferroelectric functionality to empower the existing Si-based electronics such as multi-bit storage.
△ Less
Submitted 20 June, 2021;
originally announced June 2021.
-
Single-shot Compressed 3D Imaging by Exploiting Random Scattering and Astigmatism
Authors:
Qiong Gao,
Weidong Qu,
Ming Shao,
Wei Liu,
Xiangzheng Cheng
Abstract:
Based on point spread function (PSF) engineering and astigmatism due to a pair of cylindrical lenses, a novel compressed imaging mechanism is proposed to achieve single-shot incoherent 3D imaging. The speckle-like PSF of the imaging system is sensitive to axial shift, which makes it feasible to reconstruct a 3D image by solving an optimization problem with sparsity constraint. With the experimenta…
▽ More
Based on point spread function (PSF) engineering and astigmatism due to a pair of cylindrical lenses, a novel compressed imaging mechanism is proposed to achieve single-shot incoherent 3D imaging. The speckle-like PSF of the imaging system is sensitive to axial shift, which makes it feasible to reconstruct a 3D image by solving an optimization problem with sparsity constraint. With the experimentally calibrated PSFs, the proposed method is demonstrated by a synthetic 3D point object and real 3D object, and the images in different axial slices can be reconstructed faithfully. Moreover, 3D multispectral compressed imaging is explored with the same system, and the result is rather satisfactory with a synthetic point object. Because of the inherent compatibility between the compression in spectral and axial dimensions, the proposed mechanism has the potential to be a unified framework for multi-dimensional compressed imaging.
△ Less
Submitted 20 May, 2021;
originally announced May 2021.
-
DIRC-like time-of-flight detector for the experiment at the Super Tau-Charm Facility
Authors:
Binbin Qi,
Ziwei Li,
Ming Shao,
Jianbei Liu,
Zhujun Fang,
Huangchao Shi,
Xin Li
Abstract:
The Super Tau-Charm Facility (STCF) is a future electron-positron collider proposed in China with a peak luminosity of above 0.5$\times$10$^{35}$ cm$^{-2}$s$^{-1}$ and center-of-mass energy ranging from 2 to 7 GeV. An excellent particle identification (PID) capability is one of the most important requirements for the detector at the STCF. A 3$σ$ $π$/K separation power at the momentum of up to 2 Ge…
▽ More
The Super Tau-Charm Facility (STCF) is a future electron-positron collider proposed in China with a peak luminosity of above 0.5$\times$10$^{35}$ cm$^{-2}$s$^{-1}$ and center-of-mass energy ranging from 2 to 7 GeV. An excellent particle identification (PID) capability is one of the most important requirements for the detector at the STCF. A 3$σ$ $π$/K separation power at the momentum of up to 2 GeV/c is required within the detector acceptance. A DIRC-like time-of-flight (DTOF) detector is proposed to meet the PID requirement for the endcap region of the STCF. The conceptual design of the DTOF detector and its geometry optimization is herein presented. The PID performance of the detector is studied using Geant4 simulation. With a proper reconstruction algorithm, an overall time resolution of ~50 ps is achieved for the detector with an optimum geometry when convoluting contributions from all other sources, including the transit time spread (TTS) of the photodetector, electronic timing accuracy, and an assumed precision (~40 ps) of the event start time. A $π$/K separation power of better than 4$σ$ at the momentum of 2 GeV/c is achieved over the entire sensitive area of the DTOF detector, thereby fulfilling the physics requirement of the PID detector for the experiment at the STCF.
△ Less
Submitted 14 July, 2021; v1 submitted 12 April, 2021;
originally announced April 2021.
-
Quality Assurance Test of Silicon Photomultipliers and Electronic Boards for STAR Event Plane Detector
Authors:
Ming Shao,
Yitao Wu,
Zheng Liang,
Kaifeng Shen,
Zebo Tang,
M. A. Lisa,
R. Reed,
G. Visser,
Yongjie Sun,
Yi Zhou,
Jian Zhou,
Guofeng Song,
Dongdong Hu,
Xu Wang,
Xinjian Wang
Abstract:
The event plane detector (EPD), installed in the Solenoid Tracker at the Relativistic Heavy-Ion Collider located at the Brookhaven National Laboratory is a plastic scintillator-based device that measures the reaction centrality and event plane in the forward region of the relativistic heavy-ion collisions. We used silicon photomultiplier (SiPM) arrays to detect the photons produced in the scintill…
▽ More
The event plane detector (EPD), installed in the Solenoid Tracker at the Relativistic Heavy-Ion Collider located at the Brookhaven National Laboratory is a plastic scintillator-based device that measures the reaction centrality and event plane in the forward region of the relativistic heavy-ion collisions. We used silicon photomultiplier (SiPM) arrays to detect the photons produced in the scintillator via the fiber connection. Signals from the SiPM arrays were amplified by the front-end electronic (FEE) board, and sent to the analog-to-digital converter (ADC) boards for further processing via the receiver(RX) board. The full EPD system consisted of 24 super-sectors (SSs); each SS was equipped with two SiPM boards, two FEE boards and two RX boards, and they corresponded to 744 readout channels. All these boards were mass produced at the University of Science and Technology of China, with a dedicated quality assurance (QA) procedures applied to identify any problems before deployment. This article describes the details of the QA method and the related test system. The QA test results are presented along with the discussions.
△ Less
Submitted 22 November, 2020;
originally announced November 2020.
-
Direct Multipixel Imaging and Spectroscopy of an Exoplanet with a Solar Gravity Lens Mission
Authors:
Slava G. Turyshev,
Michael Shao,
Viktor T. Toth,
Louis D. Friedman,
Leon Alkalai,
Dmitri Mawet,
Janice Shen,
Mark R. Swain,
Hanying Zhou,
Henry Helvajian,
Tom Heinsheimer,
Siegfried Janson,
Zigmond Leszczynski,
John McVey,
Darren Garber,
Artur Davoyan,
Seth Redfield,
Jared R. Males
Abstract:
We examined the solar gravitational lens (SGL) as the means to produce direct high-resolution, multipixel images of exoplanets. The properties of the SGL are remarkable: it offers maximum light amplification of ~1e11 and angular resolution of ~1e-10 arcsec. A probe with a 1-m telescope in the SGL focal region can image an exoplanet at 30 pc with 10-kilometer resolution on its surface, sufficient t…
▽ More
We examined the solar gravitational lens (SGL) as the means to produce direct high-resolution, multipixel images of exoplanets. The properties of the SGL are remarkable: it offers maximum light amplification of ~1e11 and angular resolution of ~1e-10 arcsec. A probe with a 1-m telescope in the SGL focal region can image an exoplanet at 30 pc with 10-kilometer resolution on its surface, sufficient to observe seasonal changes, oceans, continents, surface topography. We reached and exceeded all objectives set for our study: We developed a new wave-optical approach to study the imaging of exoplanets while treating them as extended, resolved, faint sources at large but finite distances. We properly accounted for the solar corona brightness. We developed deconvolution algorithms and demonstrated the feasibility of high-quality image reconstruction under realistic conditions. We have proven that multipixel imaging and spectroscopy of exoplanets with the SGL are feasible. We have developed a new mission concept that delivers an array of optical telescopes to the SGL focal region relying on three innovations: i) a new way to enable direct exoplanet imaging, ii) use of smallsats solar sails fast transit through the solar system and beyond, iii) an open architecture to take advantage of swarm technology. This approach enables entirely new missions, providing a great leap in capabilities for NASA and the greater aerospace community. Our results are encouraging as they lead to a realistic design for a mission that will be able to make direct resolved images of exoplanets in our stellar neighborhood. It could allow exploration of exoplanets relying on the SGL capabilities decades, if not centuries, earlier than possible with other extant technologies. The architecture and mission concepts for a mission to the strong interference region of the SGL are promising and should be explored further.
△ Less
Submitted 19 March, 2020; v1 submitted 26 February, 2020;
originally announced February 2020.
-
The STAR Event Plane Detector
Authors:
Joseph Adams,
Annika Ewigleben,
Sierra Garrett,
Wanbing He,
Te-Chuan Huang,
Peter M. Jacobs,
Xinyue Ju,
Michael A. Lisa,
Michael Lomnitz,
Robert Pak,
Rosi Reed,
Alexander Schmah,
Prashanth Shanmuganathan,
Ming Shao,
Xu Sun,
Isaac Upsal,
Gerard Visser,
**long Zhang
Abstract:
The Event Plane Detector (EPD) is an upgrade detector to the STAR experiment at RHIC, designed to measure the pattern of forward-going charged particles emitted in a high-energy collision between heavy nuclei. It consists of two highly-segmented disks of 1.2-cm-thick scintillator embedded with wavelength-shifting fiber, coupled to silicon photomultipliers and custom electronics. We describe the ge…
▽ More
The Event Plane Detector (EPD) is an upgrade detector to the STAR experiment at RHIC, designed to measure the pattern of forward-going charged particles emitted in a high-energy collision between heavy nuclei. It consists of two highly-segmented disks of 1.2-cm-thick scintillator embedded with wavelength-shifting fiber, coupled to silicon photomultipliers and custom electronics. We describe the general design of the device, its construction, and performance on the bench and in the experiment.
△ Less
Submitted 17 April, 2020; v1 submitted 11 December, 2019;
originally announced December 2019.
-
Deep-ultraviolet second harmonic generation in a conventional crystal quartz by freeing phase-matching in nonlinear optics
Authors:
Mingchuan Shao,
Fei Liang,
Haohai Yu,
Huai** Zhang
Abstract:
Nonlinear frequency conversion in optics can originate the coherent light at the wavelength where it is hard or unlikely to achieve by directly lasing and is a fundamental topic in science and engineering covering both classical and quantum regions. The critical requirement for efficient nonlinear frequency conversion is phase-matching, a momentum conservation relation between the fundamental and…
▽ More
Nonlinear frequency conversion in optics can originate the coherent light at the wavelength where it is hard or unlikely to achieve by directly lasing and is a fundamental topic in science and engineering covering both classical and quantum regions. The critical requirement for efficient nonlinear frequency conversion is phase-matching, a momentum conservation relation between the fundamental and harmonic light. It is dreaming of a technique for compensating the phase-mismatching in universal nonlinear materials and wavelength ranges, since the phase-matching was proposed in 1962. Here, an additional periodic phase (APP) concept was proposed for the phase-matching in nonlinear optics and experimentally demonstrated the APP phase-matched second harmonic generation with a conventional crystal quartz at the wavelength deep to vacuum-ultraviolet 177.3 nm. This study may not only develop a universal way to resuscitate the nonlinear optical materials for efficient nonlinear frequency conversion, but also may revolutionize the nonlinear photonics and their further applications.
△ Less
Submitted 28 November, 2019;
originally announced November 2019.
-
A thermal bonding method for manufacturing Micromegas detectors
Authors:
Jianxin Feng,
Zhiyong Zhang,
Jianbei Liu,
Binbin Qi,
Anqi Wang,
Ming Shao,
Yi Zhou
Abstract:
For manufacturing Micromegas detectors, the "bulk" method based on photoetching, was successfully developed and widely used in nuclear and particle physics experiments. However, the complexity of the method requires a considerable number of advanced instruments and processing, limiting the accessibility of this method for production of Micromegas detectors. In view of these limitations with the bu…
▽ More
For manufacturing Micromegas detectors, the "bulk" method based on photoetching, was successfully developed and widely used in nuclear and particle physics experiments. However, the complexity of the method requires a considerable number of advanced instruments and processing, limiting the accessibility of this method for production of Micromegas detectors. In view of these limitations with the bulk method, a new method based on thermal bonding technique (TBM) has been developed to manufacture Micromegas detectors in a much simplified and efficient way without etching. This paper describes the TBM in detail and presents performance of the Micromegas detectors built with the TBM. The effectiveness of this method was investigated by testing Micromegas detector prototypes built with the method. Both X-rays and electron beams were used to characterize the prototypes in a gas mixture of argon and CO2 (7%). A typical energy resolution of ~16% (full width at half maximum, FWHM) and an absolute gain greater than 10^4 were obtained with 5.9 keV X-rays. Detection efficiency greater than 98% and a spatial resolution of ~65 μm were achieved using a 5 GeV electron beam at the DESY test-beam facility. The gas gain of a Micromegas detector could reach up to 10^5 with a uniformity of better than 10% when the size of the avalanche gap was optimized thanks to the flexibility of the TBM in defining the gap. Additionally, the TBM facilitates the exploration of new detector structures based on Micromegas owing to the much-simplified operation with the method.
△ Less
Submitted 10 December, 2020; v1 submitted 7 October, 2019;
originally announced October 2019.
-
Extensive beam test study of prototype MRPCs for the T0 detector at the CSR external-target experiment
Authors:
Dongdong Hu,
Jiaming Lu,
Jian Zhou,
Peipei Deng,
Ming Shao,
Yongjie Sun,
Lei Zhao,
Hongfang Chen,
Cheng Li,
Zebo Tang,
Yifei Zhang,
Yi Zhou,
Wenhao You,
Guofeng Song,
Yitao Wu
Abstract:
The CSR External-target Experiment (CEE) will be the first large-scale nuclear physics experiment device at the Cooling Storage Ring (CSR) of the Heavy-Ion Research Facility in Lanzhou (HIRFL) in China. A new T0 detector has been proposed to measure the multiplicity, angular distribution and timing information of charged particles produced in heavy-ion collisions at the target region. Multi-gap re…
▽ More
The CSR External-target Experiment (CEE) will be the first large-scale nuclear physics experiment device at the Cooling Storage Ring (CSR) of the Heavy-Ion Research Facility in Lanzhou (HIRFL) in China. A new T0 detector has been proposed to measure the multiplicity, angular distribution and timing information of charged particles produced in heavy-ion collisions at the target region. Multi-gap resistive plate chamber (MRPC) technology was chosen as part of the construction of the T0 detector, which provides precision event collision times (T0) and collision geometry information. The prototype was tested with hadron and heavy-ion beams to study its performance. By comparing the experimental results with a Monte Carlo simulation, the time resolution of the MRPCs are found to be $\sim$ 50 ps or better. The timing performance of the T0 detector, including both detector and readout electronics, we found to fulfil the requirements of the CEE.
△ Less
Submitted 25 September, 2019;
originally announced September 2019.
-
Measurement of the neutron beam profile of the Back-n white neutron facility at CSNS with a Micromegas detector
Authors:
Binbin Qi,
Yang Li,
Danyang Zhu,
Zhiyong Zhang,
Ruirui Fan,
Jiang Pan,
Jianxin Feng,
Chengming Liu,
Changqing Feng,
Jianbei Liu,
Ming Shao,
Yi Zhou,
Yanfeng Wang,
Han Yi,
Qi An,
Huaiyong Bai,
Jie Bao,
** Cao,
Qi** Chen,
Yonghao Chen,
Pin**g Cheng,
Zengqi Cui,
Minhao Gu,
Fengqin Guo,
Changcai Han
, et al. (62 additional authors not shown)
Abstract:
The Back-n white neutron beam line, which uses back-streaming white neutrons from the spallation target of the China Spallation Neutron Source, is used for nuclear data measurements. A Micromegas-based neutron detector with two variants was specially developed to measure the beam spot distribution for this beam line. In this article, the design, fabrication, and characterization of the detector ar…
▽ More
The Back-n white neutron beam line, which uses back-streaming white neutrons from the spallation target of the China Spallation Neutron Source, is used for nuclear data measurements. A Micromegas-based neutron detector with two variants was specially developed to measure the beam spot distribution for this beam line. In this article, the design, fabrication, and characterization of the detector are described. The results of the detector performance tests are presented, which include the relative electron transparency, the gain and the gain uniformity, and the neutron beam profile reconstruction capability. The result of the first measurement of the Back-n neutron beam spot distribution is also presented.
△ Less
Submitted 19 January, 2020; v1 submitted 6 August, 2019;
originally announced August 2019.
-
Hydrogen Polarity of Interfacial Water Regulates Heterogeneous Ice Nucleation
Authors:
Mingzhe Shao,
Chuanbiao Zhang,
Conghai Qi,
Chunlei Wang,
Jianjun Wang,
Fangfu Ye,
Xin Zhou
Abstract:
Using all-atomic molecular dynamics(MD) simulations, we show that various substrates could induce interfacial water (IW) to form the same ice-like oxygen lattice but different hydrogen polarity order, and regulate the heterogeneous ice nucleation on the IW. We develop an efficient MD method to probe the shape, structure of ice nuclei and the corresponding supercooling temperatures. We find that th…
▽ More
Using all-atomic molecular dynamics(MD) simulations, we show that various substrates could induce interfacial water (IW) to form the same ice-like oxygen lattice but different hydrogen polarity order, and regulate the heterogeneous ice nucleation on the IW. We develop an efficient MD method to probe the shape, structure of ice nuclei and the corresponding supercooling temperatures. We find that the polarization of hydrogens in IW increases the surface tension between the ice nucleus and the IW, thus lifts the free energy barrier of heterogeneous ice nucleation. The results show that not only the oxygen lattice order but the hydrogen disorder of IW on substrates are required to effectively facilitate the freezing of atop water.
△ Less
Submitted 6 June, 2019;
originally announced June 2019.
-
I-mode investigation on the Experimental Advanced Superconducting Tokamak
Authors:
X. Feng,
A. D. Liu,
C. Zhou,
Z. X. Liu,
M. Y. Wang,
G. Zhuang,
X. L. Zou,
T. B. Wang,
Y. Z. Zhang,
J. L. Xie,
H. Q. Liu,
T. Zhang,
Y. Liu,
Y. M. Duan,
L. Q. Hu,
G. H. Hu,
D. F. Kong,
S. X. Wang,
H. L. Zhao,
Y. Y. Li,
L. M. Shao,
T. Y. Xia,
W. X. Ding,
T. Lan,
H. Li
, et al. (13 additional authors not shown)
Abstract:
By analyzing large quantities of discharges in the unfavorable ion $ \vec B\times \nabla B $ drift direction, the I-mode operation has been confirmed in EAST tokamak. During the L-mode to I-mode transition, the energy confinement has a prominent improvement by the formation of a high-temperature edge pedestal, while the particle confinement remains almost identical to that in the L-mode. Similar w…
▽ More
By analyzing large quantities of discharges in the unfavorable ion $ \vec B\times \nabla B $ drift direction, the I-mode operation has been confirmed in EAST tokamak. During the L-mode to I-mode transition, the energy confinement has a prominent improvement by the formation of a high-temperature edge pedestal, while the particle confinement remains almost identical to that in the L-mode. Similar with the I-mode observation on other devices, the $ E_r $ profiles obtained by the eight-channel Doppler backscattering system (DBS8)\cite{J.Q.Hu} show a deeper edge $ E_r $ well in the I-mode than that in the L-mode. And a weak coherent mode (WCM) with the frequency range of 40-150 kHz is observed at the edge plasma with the radial extend of about 2-3 cm. WCM could be observed in both density fluctuation and radial electric field fluctuation, and the bicoherence analyses showed significant couplings between WCM and high frequency turbulence, implying that the $ E_r $ fluctuation and the caused flow shear from WCM should play an important role during I-mode. In addition, a low-frequency oscillation with a frequency range of 5-10 kHz is always accompanied with WCM, where GAM intensity is decreased or disappeared. Many evidences show that the a low-frequency oscillation may be a novel kind of limited cycle oscillation but further investigations are needed to explain the new properties such as the harmonics and obvious magnetical perturbations.
△ Less
Submitted 31 May, 2019; v1 submitted 13 February, 2019;
originally announced February 2019.
-
MRPC3b mass production for CBM-TOF and eTOF at STAR
Authors:
D Hu,
D Sauter,
Y Sun,
I Deppner,
N Herrmann,
J Brandt,
H Chen,
E Lavrik,
C Li,
M Shao,
C Simon,
Z Tang,
X Wang,
Ph Weidenkaff,
Y Zhang,
J Zhou,
H Zeng
Abstract:
The Compressed Baryonic Matter (CBM) spectrometer aims to study strongly interacting matter under extreme conditions. The key element providing hadron identification at incident energies between 2 and 11 AGeV in heavy-ion collisions at the SIS100 accelerator is a Time-of-Flight (TOF) wall covering the polar angular range from $2.5^0$ --$25^0$ and full azimuth. CBM is expected to be operational in…
▽ More
The Compressed Baryonic Matter (CBM) spectrometer aims to study strongly interacting matter under extreme conditions. The key element providing hadron identification at incident energies between 2 and 11 AGeV in heavy-ion collisions at the SIS100 accelerator is a Time-of-Flight (TOF) wall covering the polar angular range from $2.5^0$ --$25^0$ and full azimuth. CBM is expected to be operational in the year 2024 at the Facility for Anti-proton and Ion Research (FAIR) in Darmstadt, Germany. The existing conceptual design foresees a 120 m^2 TOF-wall composed of Multi-gap Resistive Plate Chambers (MRPC) which is subdivided into a high rate region, a middle rate region and a low rate region. The MRPC3b Multistrip-MRPCs, foreseen to be integrated in the low rate region, have to cope with charged particle fluxes up to 1 kHz/cm2 and therefore will be constructed with thin float glass (0.28 mm thickness) as resistive electrode material. In the scope of the FAIR phase 0 program it is planned to install about 36 \% of the MRPC3b counters in the east endcap region of the STAR experiment at BNL as an upgrade for the Beam Energy Scan campaign (BESII) in 2019/2020.
△ Less
Submitted 6 July, 2018;
originally announced July 2018.
-
Accelerating Optical Absorption Spectra and Exciton Energy Computation for Nanosystems via Interpolative Separable Density Fitting
Authors:
Wei Hu,
Meiyue Shao,
Andrea Cepellotti,
Felipe H. da Jornada,
Lin Lin,
Kyle Thicke,
Chao Yang,
Steven G. Louie
Abstract:
We present an efficient way to solve the Bethe-Salpeter equation (BSE), a model for the computation of absorption spectra in molecules and solids that includes electron-hole excitations. Standard approaches to construct and diagonalize the Bethe-Salpeter Hamiltonian require at least $Ø(N_e^5)$ operations, where $N_e$ is proportional to the number of electrons in the system, limiting its applicatio…
▽ More
We present an efficient way to solve the Bethe-Salpeter equation (BSE), a model for the computation of absorption spectra in molecules and solids that includes electron-hole excitations. Standard approaches to construct and diagonalize the Bethe-Salpeter Hamiltonian require at least $Ø(N_e^5)$ operations, where $N_e$ is proportional to the number of electrons in the system, limiting its application to small systems. Our approach is based on the interpolative separable density fitting (ISDF) technique to construct low rank approximations to the bare and screened exchange operators associated with the BSE Hamiltonian. This approach reduces the complexity of the Hamiltonian construction to $Ø(N_e^3)$ with a much smaller pre-constant. Here, we implement the ISDF method for the BSE calculations within the Tamm-Dancoff approximation (TDA) in the BerkeleyGW software package. We show that ISDF-based BSE calculations in molecules and solids reproduce accurate exciton energies and optical absorption spectra with significantly reduced computational cost.
△ Less
Submitted 30 January, 2018; v1 submitted 26 January, 2018;
originally announced January 2018.
-
Luminosity measurements for the R scan experiment at BESIII
Authors:
M. Ablikim,
M. N. Achasov,
S. Ahmed,
X. C. Ai,
O. Albayrak,
M. Albrecht,
D. J. Ambrose,
A. Amoroso,
F. F. An,
Q. An,
J. Z. Bai,
O. Bakina,
R. Baldini Ferroli,
Y. Ban,
D. W. Bennett,
J. V. Bennett,
N. Berger,
M. Bertani,
D. Bettoni,
J. M. Bian,
F. Bianchi,
E. Boger,
I. Boyko,
R. A. Briere,
H. Cai
, et al. (405 additional authors not shown)
Abstract:
By analyzing the large-angle Bhabha scattering events $e^{+}e^{-}$ $\to$ ($γ$)$e^{+}e^{-}$ and diphoton events $e^{+}e^{-}$ $\to$ $γγ$ for the data sets collected at center-of-mass (c.m.) energies between 2.2324 and 4.5900 GeV (131 energy points in total) with the upgraded Bei**g Spectrometer (BESIII) at the Bei**g Electron-Positron Collider (BEPCII), the integrated luminosities have been measur…
▽ More
By analyzing the large-angle Bhabha scattering events $e^{+}e^{-}$ $\to$ ($γ$)$e^{+}e^{-}$ and diphoton events $e^{+}e^{-}$ $\to$ $γγ$ for the data sets collected at center-of-mass (c.m.) energies between 2.2324 and 4.5900 GeV (131 energy points in total) with the upgraded Bei**g Spectrometer (BESIII) at the Bei**g Electron-Positron Collider (BEPCII), the integrated luminosities have been measured at the different c.m. energies, individually. The results are the important inputs for R value and $J/ψ$ resonance parameter measurements.
△ Less
Submitted 11 February, 2017;
originally announced February 2017.
-
A structure preserving Lanczos algorithm for computing the optical absorption spectrum
Authors:
Meiyue Shao,
Felipe H. da Jornada,
Lin Lin,
Chao Yang,
Jack Deslippe,
Steven G. Louie
Abstract:
We present a new structure preserving Lanczos algorithm for approximating the optical absorption spectrum in the context of solving full Bethe--Salpeter equation without Tamm--Dancoff approximation. The new algorithm is based on a structure preserving Lanczos procedure, which exploits the special block structure of Bethe--Salpeter Hamiltonian matrices. A recently developed technique of generalized…
▽ More
We present a new structure preserving Lanczos algorithm for approximating the optical absorption spectrum in the context of solving full Bethe--Salpeter equation without Tamm--Dancoff approximation. The new algorithm is based on a structure preserving Lanczos procedure, which exploits the special block structure of Bethe--Salpeter Hamiltonian matrices. A recently developed technique of generalized averaged Gauss quadrature is incorporated to accelerate the convergence. We also establish the connection between our structure preserving Lanczos procedure with several existing Lanczos procedures developed in different contexts. Numerical examples are presented to demonstrate the effectiveness of our Lanczos algorithm.
△ Less
Submitted 5 September, 2017; v1 submitted 7 November, 2016;
originally announced November 2016.
-
Accelerating Nuclear Configuration Interaction Calculations through a Preconditioned Block Iterative Eigensolver
Authors:
Meiyue Shao,
Hasan Metin Aktulga,
Chao Yang,
Esmond G. Ng,
Pieter Maris,
James P. Vary
Abstract:
We describe a number of recently developed techniques for improving the performance of large-scale nuclear configuration interaction calculations on high performance parallel computers. We show the benefit of using a preconditioned block iterative method to replace the Lanczos algorithm that has traditionally been used to perform this type of computation. The rapid convergence of the block iterati…
▽ More
We describe a number of recently developed techniques for improving the performance of large-scale nuclear configuration interaction calculations on high performance parallel computers. We show the benefit of using a preconditioned block iterative method to replace the Lanczos algorithm that has traditionally been used to perform this type of computation. The rapid convergence of the block iterative method is achieved by a proper choice of starting guesses of the eigenvectors and the construction of an effective preconditioner. These acceleration techniques take advantage of special structure of the nuclear configuration interaction problem which we discuss in detail. The use of a block method also allows us to improve the concurrency of the computation, and take advantage of the memory hierarchy of modern microprocessors to increase the arithmetic intensity of the computation relative to data movement. We also discuss implementation details that are critical to achieving high performance on massively parallel multi-core supercomputers, and demonstrate that the new block iterative solver is two to three times faster than the Lanczos based algorithm for problems of moderate sizes on a Cray XC30 system.
△ Less
Submitted 8 September, 2017; v1 submitted 6 September, 2016;
originally announced September 2016.
-
Low Rank Approximation in $G_0W_0$ Approximation
Authors:
Meiyue Shao,
Lin Lin,
Chao Yang,
Fang Liu,
Felipe H. da Jornada,
Jack Deslippe,
Steven G. Louie
Abstract:
The single particle energies obtained in a Kohn--Sham density functional theory (DFT) calculation are generally known to be poor approximations to electron excitation energies that are measured in transport, tunneling and spectroscopic experiments such as photo-emission spectroscopy. The correction to these energies can be obtained from the poles of a single particle Green's function derived from…
▽ More
The single particle energies obtained in a Kohn--Sham density functional theory (DFT) calculation are generally known to be poor approximations to electron excitation energies that are measured in transport, tunneling and spectroscopic experiments such as photo-emission spectroscopy. The correction to these energies can be obtained from the poles of a single particle Green's function derived from a many-body perturbation theory. From a computational perspective, the accuracy and efficiency of such an approach depends on how a self energy term that properly accounts for dynamic screening of electrons is approximated. The $G_0W_0$ approximation is a widely used technique in which the self energy is expressed as the convolution of a non-interacting Green's function ($G_0$) and a screened Coulomb interaction ($W_0$) in the frequency domain. The computational cost associated with such a convolution is high due to the high complexity of evaluating $W_0$ at multiple frequencies. In this paper, we discuss how the cost of $G_0W_0$ calculation can be reduced by constructing a low rank approximation to the frequency dependent part of $W_0$. In particular, we examine the effect of such a low rank approximation on the accuracy of the $G_0W_0$ approximation. We also discuss how the numerical convolution of $G_0$ and $W_0$ can be evaluated efficiently and accurately by using a contour deformation technique with an appropriate choice of the contour.
△ Less
Submitted 7 May, 2016;
originally announced May 2016.
-
Cosmic Ray Test of Mini-drift Thick Gas Electron Multiplier Chamber for Transition Radiation Detector
Authors:
S. Yang,
S. Das,
B. Buck,
C. Li,
T. Ljubicic,
R. Majka,
M. Shao,
N. Smirnov,
G. Visser,
Z. Xu,
Y. Zhou
Abstract:
A thick gas electron multiplier (THGEM) chamber with an effective readout area of 10$\times$10 cm$^{2}$ and a 11.3 mm ionization gap has been tested along with two regular gas electron multiplier (GEM) chambers in a cosmic ray test system. The thick ionization gap makes the THGEM chamber a mini-drift chamber. This kind mini-drift THGEM chamber is proposed as part of a transition radiation detector…
▽ More
A thick gas electron multiplier (THGEM) chamber with an effective readout area of 10$\times$10 cm$^{2}$ and a 11.3 mm ionization gap has been tested along with two regular gas electron multiplier (GEM) chambers in a cosmic ray test system. The thick ionization gap makes the THGEM chamber a mini-drift chamber. This kind mini-drift THGEM chamber is proposed as part of a transition radiation detector (TRD) for identifying electrons at an Electron Ion Collider (EIC) experiment. Through this cosmic ray test, an efficiency larger than 94$\%$ and a spatial resolution $\sim$220 $μ$m are achieved for the THGEM chamber at -3.65 kV. Thanks to its outstanding spatial resolution and thick ionization gap, the THGEM chamber shows excellent track reconstruction capability. The gain uniformity and stability of the THGEM chamber are also presented.
△ Less
Submitted 17 February, 2015; v1 submitted 14 December, 2014;
originally announced December 2014.
-
A Cosmic Ray Test Platform Based on the High Time Resolution MRPC Technology
Authors:
Tianxiang Chen,
Cheng Li,
Yongjie Sun,
Hongfang Chen,
Ming Shao,
Zebo Tang,
Rongxing Yang,
Yi Zhou,
Yifei Zhang
Abstract:
In order to test the performance of detector/prototype in environment of laboratory, we design and build a larger area ($90\times52$ $cm^2$) test platform of cosmic ray based on well-designed Multi-gap Resistive Plate Chamber (MRPC) with an excellent time resolution and a high detection efficiency for the minimum ionizing particles (MIPs). The time resolution of the MRPC module used is tested to b…
▽ More
In order to test the performance of detector/prototype in environment of laboratory, we design and build a larger area ($90\times52$ $cm^2$) test platform of cosmic ray based on well-designed Multi-gap Resistive Plate Chamber (MRPC) with an excellent time resolution and a high detection efficiency for the minimum ionizing particles (MIPs). The time resolution of the MRPC module used is tested to be ~80 ps, and the position resolution along the strip is ~5 mm, while the position resolution perpendicular to the strip is ~12.7 mm. The platform constructed by four MRPC modules can be functional for tracking the cosmic rays with a spatial resolution ~6.3 mm, and provide a reference time ~40 ps.
△ Less
Submitted 13 March, 2015; v1 submitted 25 August, 2014;
originally announced August 2014.
-
Test of High Time Resolution MRPC with Different Readout Modes
Authors:
S. Yang,
Y. J. Sun,
C. Li,
Y. K. Heng,
S. Qian,
H. F. Chen,
T. X. Chen,
H. L. Dai,
H. H. Fan,
S. B. Liu,
S. D. Liu,
X. S. Jiang,
M. Shao,
Z. B. Tang,
H. Zhang,
Z. G. Zhao
Abstract:
In order to further enhance the particle identification capability of the Bei**g Spectrometer (BESIII), it is proposed to upgrade the current end-cap time-of-flight (eTOF) detector with multi-gap resistive plate chamber (MRPC). The prototypes, together with the front end electronics (FEE) and time digitizer (TDIG) module have been tested at the E3 line of Bei**g Electron Positron Collider (BEPCI…
▽ More
In order to further enhance the particle identification capability of the Bei**g Spectrometer (BESIII), it is proposed to upgrade the current end-cap time-of-flight (eTOF) detector with multi-gap resistive plate chamber (MRPC). The prototypes, together with the front end electronics (FEE) and time digitizer (TDIG) module have been tested at the E3 line of Bei**g Electron Positron Collider (BEPCII) to study the difference between the single and double-end readout MRPC designs. The time resolutions (sigma) of the single-end readout MRPC are 47/53 ps obtained by 600 MeV/c proton/pion beam, while that of the double-end readout MRPC is 40 ps (proton beam). The efficiencies of three MRPC modules tested by both proton and pion beam are better than 98%. For the double-end readout MRPC, no incident position dependence is observed.
△ Less
Submitted 8 May, 2014;
originally announced May 2014.
-
A Large area GEM Detector Using an improved Self-stretch Technique
Authors:
Wenhao You,
Yi Zhou,
Cheng Li,
Hongfang Chen,
Ming Shao,
Yongjie Sun,
Zebo Tang,
Jianbei Liu
Abstract:
A GEM detector with an effective area of 30*30 cm2 has been constructed using an improved self-stretch technique, which enables an easy and fast GEM assembling. The design and assembling of the detector is described. Results from tests of the detector with 8 keV X-rays on effective gain and energy resolution are presented.
A GEM detector with an effective area of 30*30 cm2 has been constructed using an improved self-stretch technique, which enables an easy and fast GEM assembling. The design and assembling of the detector is described. Results from tests of the detector with 8 keV X-rays on effective gain and energy resolution are presented.
△ Less
Submitted 8 May, 2014;
originally announced May 2014.
-
Measurements of Baryon Pair Decays of $χ_{cJ}$ Mesons
Authors:
M. Ablikim,
M. N. Achasov,
O. Albayrak,
D. J. Ambrose,
F. F. An,
Q. An,
J. Z. Bai,
Y. Ban,
J. Becker,
J. V. Bennett,
M. Bertani,
J. M. Bian,
E. Boger,
O. Bondarenko,
I. Boyko,
R. A. Briere,
V. Bytev,
X. Cai,
O. Cakir,
A. Calcaterra,
G. F. Cao,
S. A. Cetin,
J. F. Chang,
G. Chelkov,
G. Chen
, et al. (326 additional authors not shown)
Abstract:
Using 106 $\times 10^{6}$ $ψ^{\prime}$ decays collected with the BESIII detector at the BEPCII, three decays of $χ_{cJ}$ ($J=0,1,2$) with baryon pairs ($\llb$, $\ssb$, $\SSB$) in the final state have been studied. The branching fractions are measured to be $\cal{B}$$(χ_{c0,1,2}\rightarrowΛ\barΛ) =(33.3 \pm 2.0 \pm 2.6)\times 10^{-5}$, $(12.2 \pm 1.1 \pm 1.1)\times 10^{-5}$,…
▽ More
Using 106 $\times 10^{6}$ $ψ^{\prime}$ decays collected with the BESIII detector at the BEPCII, three decays of $χ_{cJ}$ ($J=0,1,2$) with baryon pairs ($\llb$, $\ssb$, $\SSB$) in the final state have been studied. The branching fractions are measured to be $\cal{B}$$(χ_{c0,1,2}\rightarrowΛ\barΛ) =(33.3 \pm 2.0 \pm 2.6)\times 10^{-5}$, $(12.2 \pm 1.1 \pm 1.1)\times 10^{-5}$, $(20.8 \pm 1.6 \pm 2.3)\times 10^{-5}$; $\cal{B}$$(χ_{c0,1,2}\rightarrowΣ^{0}\barΣ^{0})$ = $(47.8 \pm 3.4 \pm 3.9)\times 10^{-5}$, $(3.8 \pm 1.0 \pm 0.5)\times 10^{-5}$, $(4.0 \pm 1.1 \pm 0.5) \times 10^{-5}$; and $\cal{B}$$(χ_{c0,1,2}\rightarrowΣ^{+}\barΣ^{-})$ = $(45.4 \pm 4.2 \pm 3.0)\times 10^{-5}$, $(5.4 \pm 1.5 \pm 0.5)\times 10^{-5}$, $(4.9 \pm 1.9 \pm 0.7)\times 10^{-5}$, where the first error is statistical and the second is systematic. Upper limits on the branching fractions for the decays of $χ_{c1,2}\rightarrowΣ^{0}\barΣ^{0}$, $Σ^{+}\barΣ^{-}$, are estimated to be $\cal{B}$$(χ_{c1}\rightarrowΣ^{0}\barΣ^{0}) < 6.2\times 10^{-5}$, $\cal{B}$$(χ_{c2}\rightarrowΣ^{0}\barΣ^{0}) < 6.5\times 10^{-5}$, $\cal{B}$$(χ_{c1}\rightarrowΣ^{+}\barΣ^{-}) < 8.7\times 10^{-5}$ and $\cal{B}$$(χ_{c2}\rightarrowΣ^{+}\barΣ^{-}) < 8.8\times 10^{-5}$ at the 90% confidence level.
△ Less
Submitted 4 March, 2013; v1 submitted 9 November, 2012;
originally announced November 2012.
-
A GEANT4 Simulation Studyof BESIII endcap TOF Upgrade
Authors:
Hui Zhang,
Ming Shao,
Cheng Li,
Hongfang Chen,
Yuekun Heng,
Yongjie Sun,
Zebo Tang Changsheng Ji,
Tianxiang Chen,
Shuai Yang,
Lailin Xu
Abstract:
A GEANT4-based Monte-Carlo model is developed to study the performance of Endcap Time-Of-Flight (ETOF) at BESIII. It's found that the multiple scattering effects, mainly from the materials at the MDC endcap, can cause multi-hit on the ETOF's readout cell and significantly influence the timing property of ETOF. Multi-gap Resistive Plate Chamber (MRPC) with a smaller readout cell structure is more s…
▽ More
A GEANT4-based Monte-Carlo model is developed to study the performance of Endcap Time-Of-Flight (ETOF) at BESIII. It's found that the multiple scattering effects, mainly from the materials at the MDC endcap, can cause multi-hit on the ETOF's readout cell and significantly influence the timing property of ETOF. Multi-gap Resistive Plate Chamber (MRPC) with a smaller readout cell structure is more suitable for ETOF detector due to significantly reduced multi-hit rate, from 71.5% for currently-used scintillator-based ETOF to 21.8% or 16.7% for MRPC-based ETOF, depending on the readout pad size used. The timing performance of a MRPC ETOF is also improved. These simulation results suggest and guide an ETOF upgrade effort at BESIII.
△ Less
Submitted 15 August, 2012;
originally announced August 2012.
-
Application of a damped Locally Optimized Combination of Images method to the spectral characterization of faint companions using an Integral Field Spectrograph
Authors:
Laurent Pueyo,
Justin R. Crepp,
Gautam Vasisht,
Douglas Brenner,
Ben R. Oppenheimer,
Neil Zimmerman,
Sasha Hinkley,
Ian Parry,
Charles Beichman,
Lynne Hillenbrand,
Lewis C. Roberts Jr.,
Richard Dekany,
Mike Shao,
Rick Burruss,
Antonin Bouchez,
Jenny Roberts,
Rémi Soummer
Abstract:
High-contrast imaging instruments are now being equipped with integral field spectrographs (IFS) to facilitate the detection and characterization of faint substellar companions. Algorithms currently envisioned to handle IFS data, such as the Locally Optimized Combination of Images (LOCI) algorithm, rely upon aggressive point-spread-function (PSF) subtraction, which is ideal for initially identifyi…
▽ More
High-contrast imaging instruments are now being equipped with integral field spectrographs (IFS) to facilitate the detection and characterization of faint substellar companions. Algorithms currently envisioned to handle IFS data, such as the Locally Optimized Combination of Images (LOCI) algorithm, rely upon aggressive point-spread-function (PSF) subtraction, which is ideal for initially identifying companions but results in significantly biased photometry and spectroscopy due to unwanted mixing with residual starlight. This spectro-photometric issue is further complicated by the fact that algorithmic color response is a function of the companion's spectrum, making it difficult to calibrate the effects of the reduction without using iterations involving a series of injected synthetic companions. In this paper, we introduce a new PSF calibration method, which we call "damped LOCI", that seeks to alleviate these concerns. By modifying the cost function that determines the weighting coefficients used to construct PSF reference images, and also forcing those coefficients to be positive, it is possible to extract companion spectra with a precision that is set by calibration of the instrument response and transmission of the atmosphere, and not by post-processing. We demonstrate the utility of this approach using on-sky data obtained with the Project 1640 IFS at Palomar. Damped-LOCI does not require any iterations on the underlying spectral type of the companion, nor does it rely upon priors involving the chromatic and statistical properties of speckles. It is a general technique that can readily be applied to other current and planned instruments that employ IFS's.
△ Less
Submitted 25 November, 2011;
originally announced November 2011.
-
Looking for packing units of the protein structure
Authors:
Wei-Mou Zheng,
Hui Zeng,
Dong-Bo Bu,
Ming-Fu Shao,
Ke-Song Liu,
Chao Wang
Abstract:
Lattice-model simulations and experiments of some small proteins suggest that folding is essentially controlled by a few conserved contacts. Residues of these conserved contacts form the minimum set of native contacts needed to ensure foldability. Kee** such conserved specific contacts in mind, we examine contacts made by two secondary structure elements of different helices or sheets and look f…
▽ More
Lattice-model simulations and experiments of some small proteins suggest that folding is essentially controlled by a few conserved contacts. Residues of these conserved contacts form the minimum set of native contacts needed to ensure foldability. Kee** such conserved specific contacts in mind, we examine contacts made by two secondary structure elements of different helices or sheets and look for possible 'packing units' of the protein structure. Two short backbone fragments of width five centred at the C? atoms in contact is called an H-form, which serves as a candidate for the packing units. The structural alignment of protein family members or even across families indicates that there are conservative H-forms which are similar both in their sequences and local geometry, and consistent with the structural alignment. Carrying strong sequence signals, such packing units would provide 3D constraints as a complement of the potential functions for the structure prediction.
△ Less
Submitted 13 September, 2011;
originally announced September 2011.
-
Beam test of signal cross-talk and transmission for LMPRC
Authors:
Yongjie sun,
Cheng Li,
Zebo Tang,
Lailin Xu,
Tianxiang Chen,
Ming Shao
Abstract:
A new prototype of large area Multi-gap Resistive Plate Chamber (MRPC) with long readout strips was built. This Long-strip Multi-gap Resistive Plate Chamber (LMRPC) is double stacked and has ten 250 $μ$m-thick gas gaps. Signals are read out from two ends of strip with an active area of 50 cm$\times$2.5 cm in each. The detector was tested at FOPI in GSI, using the secondary particles of proton beam…
▽ More
A new prototype of large area Multi-gap Resistive Plate Chamber (MRPC) with long readout strips was built. This Long-strip Multi-gap Resistive Plate Chamber (LMRPC) is double stacked and has ten 250 $μ$m-thick gas gaps. Signals are read out from two ends of strip with an active area of 50 cm$\times$2.5 cm in each. The detector was tested at FOPI in GSI, using the secondary particles of proton beams ($E = 3.5 GeV$) colliding with a Pb target. The results show that the LMRPC prototype has a time resolution of about 60$\sim$70 ps; the detecting efficiency is over 98% and the ratio of cross-talk is lower than 2%. The detector also has a good spatial resolution of 0.36 cm along the strip direction.
△ Less
Submitted 31 December, 2010;
originally announced January 2011.
-
New Prototype Multi-gap Resistive Plate Chambers with Long Strips
Authors:
Y. J. Sun,
C. Li,
M. Shao,
B. Gui,
Y. E. Zhao,
H. F. Chen,
Z. B. Xu,
L. J. Ruan,
G. J. Lin,
X. Wang,
Y. Wang,
Z. B. Tang,
G. Eppley,
P. Fachini,
M. Kohl,
J. Liu,
W. J. Llope,
R. Majka,
T. Nussbaun,
E. Ramberg,
T. Sakuma,
F. Simon,
N. Smirnov,
B. Surrow,
D. Underwood
Abstract:
A new kind of Multi-gap Resistive Plate Chamber (MRPC) has been built for the large-area Muon Telescope Detector (MTD) for the STAR experiment at RHIC. These long read-out strip MRPCs (LMRPCs) have an active area of 87.0 x 17.0 cm2 and ten 250 um-thick gas gaps arranged as a double stack. Each read-out strip is 2.5 cm wide and 90 cm long. The signals are read-out at both ends of each strip. Cosm…
▽ More
A new kind of Multi-gap Resistive Plate Chamber (MRPC) has been built for the large-area Muon Telescope Detector (MTD) for the STAR experiment at RHIC. These long read-out strip MRPCs (LMRPCs) have an active area of 87.0 x 17.0 cm2 and ten 250 um-thick gas gaps arranged as a double stack. Each read-out strip is 2.5 cm wide and 90 cm long. The signals are read-out at both ends of each strip. Cosmic ray tests indicate a time resolution of ~70 ps and a detection efficiency of greater than 95%. Beam tests performed at T963 at Fermilab indicate a time resolution of 60-70 ps and a spatial resolution of ~1 cm along the strip direction.
△ Less
Submitted 16 May, 2008;
originally announced May 2008.
-
Space-based research in fundamental physics and quantum technologies
Authors:
S. G. Turyshev,
U. E. Israelsson,
M. Shao,
N. Yu,
A. Kusenko,
E. L. Wright,
C. W. F. Everitt,
M. A. Kasevich,
J. A. Lipa,
J. C. Mester,
R. D. Reasenberg,
R. L. Walsworth,
N. Ashby,
H. Gould,
H. -J. Paik
Abstract:
Space-based experiments today can uniquely address important questions related to the fundamental laws of Nature. In particular, high-accuracy physics experiments in space can test relativistic gravity and probe the physics beyond the Standard Model; they can perform direct detection of gravitational waves and are naturally suited for precision investigations in cosmology and astroparticle physi…
▽ More
Space-based experiments today can uniquely address important questions related to the fundamental laws of Nature. In particular, high-accuracy physics experiments in space can test relativistic gravity and probe the physics beyond the Standard Model; they can perform direct detection of gravitational waves and are naturally suited for precision investigations in cosmology and astroparticle physics. In addition, atomic physics has recently shown substantial progress in the development of optical clocks and atom interferometers. If placed in space, these instruments could turn into powerful high-resolution quantum sensors greatly benefiting fundamental physics.
We discuss the current status of space-based research in fundamental physics, its discovery potential, and its importance for modern science. We offer a set of recommendations to be considered by the upcoming National Academy of Sciences' Decadal Survey in Astronomy and Astrophysics. In our opinion, the Decadal Survey should include space-based research in fundamental physics as one of its focus areas. We recommend establishing an Astronomy and Astrophysics Advisory Committee's interagency ``Fundamental Physics Task Force'' to assess the status of both ground- and space-based efforts in the field, to identify the most important objectives, and to suggest the best ways to organize the work of several federal agencies involved. We also recommend establishing a new NASA-led interagency program in fundamental physics that will consolidate new technologies, prepare key instruments for future space missions, and build a strong scientific and engineering community. Our goal is to expand NASA's science objectives in space by including ``laboratory research in fundamental physics'' as an element in agency's ongoing space research efforts.
△ Less
Submitted 3 March, 2008; v1 submitted 1 November, 2007;
originally announced November 2007.
-
Experimental Design for the LATOR Mission
Authors:
Slava G. Turyshev,
Michael Shao,
Kenneth L. Nordtvedt
Abstract:
This paper discusses experimental design for the Laser Astrometric Test Of Relativity (LATOR) mission. LATOR is designed to reach unprecedented accuracy of 1 part in 10^8 in measuring the curvature of the solar gravitational field as given by the value of the key Eddington post-Newtonian parameter γ. This mission will demonstrate the accuracy needed to measure effects of the next post-Newtonian…
▽ More
This paper discusses experimental design for the Laser Astrometric Test Of Relativity (LATOR) mission. LATOR is designed to reach unprecedented accuracy of 1 part in 10^8 in measuring the curvature of the solar gravitational field as given by the value of the key Eddington post-Newtonian parameter γ. This mission will demonstrate the accuracy needed to measure effects of the next post-Newtonian order (~G^2) of light deflection resulting from gravity's intrinsic non-linearity. LATOR will provide the first precise measurement of the solar quadrupole moment parameter, J2, and will improve determination of a variety of relativistic effects including Lense-Thirring precession. The mission will benefit from the recent progress in the optical communication technologies -- the immediate and natural step above the standard radio-metric techniques. The key element of LATOR is a geometric redundancy provided by the laser ranging and long-baseline optical interferometry. We discuss the mission and optical designs, as well as the expected performance of this proposed mission. LATOR will lead to very robust advances in the tests of Fundamental physics: this mission could discover a violation or extension of general relativity, or reveal the presence of an additional long range interaction in the physical law. There are no analogs to the LATOR experiment; it is unique and is a natural culmination of solar system gravity experiments.
△ Less
Submitted 8 October, 2004;
originally announced October 2004.
-
Mission Design for the Laser Astrometric Test Of Relativity
Authors:
Slava G. Turyshev,
Michael Shao,
Kenneth L. Nordtvedt
Abstract:
This paper focuses on the mission design for the Laser Astrometric Test Of Relativity (LATOR). This mission uses laser interferometry between two micro-spacecraft whose lines of sight pass close by the Sun to accurately measure deflection of light in the solar gravity. The key element of the experimental design is a redundant geometry optical truss provided by a long-baseline (100 m) multi-chann…
▽ More
This paper focuses on the mission design for the Laser Astrometric Test Of Relativity (LATOR). This mission uses laser interferometry between two micro-spacecraft whose lines of sight pass close by the Sun to accurately measure deflection of light in the solar gravity. The key element of the experimental design is a redundant geometry optical truss provided by a long-baseline (100 m) multi-channel stellar optical interferometer placed on the International Space Station (ISS). The spatial interferometer is used for measuring the angles between the two spacecraft and for orbit determination purposes. The geometric redundancy enables LATOR to measure the departure from Euclidean geometry caused by the solar gravity field to a very high accuracy. Such a design enables LATOR to improve the value of the parameterized post-Newtonian (PPN) parameter $γ$ to unprecedented levels of accuracy of 1 part in 10$^{8}$; the misison will also measure effects of the next post-Newtonian order ($\propto G^2$) of light deflection resulting from gravity's intrinsic non-linearity. The solar quadrupole moment parameter, $J_2$, will be measured with high precision, as well as a variety of other relativistic effects including Lense-Thirring precession. LATOR will lead to very robust advances in the tests of Fundamental physics: this mission could discover a violation or extension of general relativity, or reveal the presence of an additional long range interaction in the physical law.
△ Less
Submitted 29 September, 2004;
originally announced September 2004.
-
The Laser Astrometric Test of Relativity (LATOR) Mission
Authors:
Slava G. Turyshev,
Michael Shao,
Kenneth Nordtvedt Jr
Abstract:
This paper discusses new fundamental physics experiment that will test relativistic gravity at the accuracy better than the effects of the second order in the gravitational field strength, $\propto G^2$. The Laser Astrometric Test Of Relativity (LATOR) mission uses laser interferometry between two micro-spacecraft whose lines of sight pass close by the Sun to accurately measure deflection of lig…
▽ More
This paper discusses new fundamental physics experiment that will test relativistic gravity at the accuracy better than the effects of the second order in the gravitational field strength, $\propto G^2$. The Laser Astrometric Test Of Relativity (LATOR) mission uses laser interferometry between two micro-spacecraft whose lines of sight pass close by the Sun to accurately measure deflection of light in the solar gravity. The key element of the experimental design is a redundant geometry optical truss provided by a long-baseline (100 m) multi-channel stellar optical interferometer placed on the International Space Station (ISS). The spatial interferometer is used for measuring the angles between the two spacecraft and for orbit determination purposes. The geometric redundancy enables LATOR to measure the departure from Euclidean geometry caused by the solar gravity field to a very high accuracy. LATOR will not only improve the value of the parameterized post-Newtonian (PPN) $γ$ to unprecedented levels of accuracy of 1 part in 10$^{8}$, it will also reach ability to measure effects of the next post-Newtonian order ($c^{-4}$) of light deflection resulting from gravity's intrinsic non-linearity. The solar quadrupole moment parameter, $J_2$, will be measured with high precision, as well as a variety of other relativistic effects including Lense-Thirring precession. LATOR will lead to very robust advances in the tests of Fundamental physics: this mission could discover a violation or extension of general relativity, or reveal the presence of an additional long range interaction in the physical law. There are no analogs to the LATOR experiment; it is unique and is a natural culmination of solar system gravity experiments.
△ Less
Submitted 6 May, 2004; v1 submitted 7 November, 2003;
originally announced November 2003.
-
Unified Expressions Of All Integral Variational Principles
Authors:
Y. C. Huang,
Xi-Guo Lee,
Ming-Xue Shao
Abstract:
In terms of the quantitative causal principle, this paper obtains a general variational principle, gives unified expressions of the general, Hamilton, Voss, Hölder, Maupertuis-Lagrange variational principles of integral style, the invariant quantities of the general, Voss, Hölder, Maupertuis-Lagrange variational principles are given, finally the Noether conservation charges of the general, Voss,…
▽ More
In terms of the quantitative causal principle, this paper obtains a general variational principle, gives unified expressions of the general, Hamilton, Voss, Hölder, Maupertuis-Lagrange variational principles of integral style, the invariant quantities of the general, Voss, Hölder, Maupertuis-Lagrange variational principles are given, finally the Noether conservation charges of the general, Voss, Hölder, Maupertuis-Lagrange variational principles are deduced, and the intrinsic relations among the invariant quantities and the Noether conservation charges of the all integral variational principles are achieved.
△ Less
Submitted 22 June, 2006; v1 submitted 9 March, 1999;
originally announced March 1999.