Showing 1–7 of 7 results for author: Rizzi, C

Performance of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector

Authors: C. Agapopoulou, L. A. Beresford, D. E. Boumediene, L. Castillo García, S. Conforti, C. de la Taille, L. D. Corpe, M. J. Da Cunha Sargedas de Sousa, P. Dinaucourt, A. Falou, V. Gautam, D. Gong, C. Grieco, S. Grinstein, S. Guindon, A. Howard, O. Kurdysh, E. Kuwertz, C. Li, N. Makovec, B. Markovic, G. Martin-Chassal, R. Mazzini, C. Milke, M. Morenas , et al. (12 additional authors not shown)

Abstract: This paper presents the design and characterisation of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector, which is planned for the High-Luminosity phase of the LHC. This prototype, called ALTIROC1, consists of a 5$\times$5-pad matrix and contains the analog part of the single-channel readout (preamplifier, discriminator, two TDCs and SRAM). Two preamplifier architectures (t… ▽ More This paper presents the design and characterisation of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector, which is planned for the High-Luminosity phase of the LHC. This prototype, called ALTIROC1, consists of a 5$\times$5-pad matrix and contains the analog part of the single-channel readout (preamplifier, discriminator, two TDCs and SRAM). Two preamplifier architectures (transimpedance and voltage) were implemented and tested. The ASIC was characterised both alone and as a module when connected to a 5$\times$5-pad array of LGAD sensors. In calibration measurements, the ASIC operating alone was found to satisfy the technical requirements for the project, with similar performances for both preamplifier types. In particular, the jitter was found to be 15$\pm$1~ps (35$\pm$1~ps) for an injected charge of 10~fC (4~fC). A degradation in performance was observed when the ASIC was connected to the LGAD array. This is attributed to digital couplings at the entrance of the preamplifiers. When the ASIC is connected to the LGAD array, the lowest detectable charge increased from 1.5~fC to 3.4~fC. As a consequence, the jitter increased for an injected charge of 4~fC. Despite this increase, ALTIROC1 still satisfies the maximum jitter specification (below 65~ps) for the HGTD project. This coupling issue also affects the time over threshold measurements and the time-walk correction can only be performed with transimpedance preamplifiers. Beam test measurements with a pion beam at CERN were also undertaken to evaluate the performance of the module. The best time resolution obtained using only ALTIROC TDC data was 46.3$\pm$0.7~ps for a restricted time of arrival range where the coupling issue is minimized. The residual time-walk contribution is equal to 23~ps and is the dominant electronic noise contribution to the time resolution at 15~fC. △ Less

Submitted 25 July, 2023; v1 submitted 15 June, 2023; originally announced June 2023.

Comments: 20 pages, 15 figures Second version submitted to JINST including minor changes applied to address journal's comments

The FASER Detector

Authors: FASER Collaboration, Henso Abreu, Elham Amin Mansour, Claire Antel, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David W. Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Olivier Crespo-Lopez, Stephane Debieux, Monica D'Onofrio, Liam Dougherty, Candan Dozen, Abdallah Ezzat, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere , et al. (72 additional authors not shown)

Abstract: FASER, the ForwArd Search ExpeRiment, is an experiment dedicated to searching for light, extremely weakly-interacting particles at CERN's Large Hadron Collider (LHC). Such particles may be produced in the very forward direction of the LHC's high-energy collisions and then decay to visible particles inside the FASER detector, which is placed 480 m downstream of the ATLAS interaction point, aligned… ▽ More FASER, the ForwArd Search ExpeRiment, is an experiment dedicated to searching for light, extremely weakly-interacting particles at CERN's Large Hadron Collider (LHC). Such particles may be produced in the very forward direction of the LHC's high-energy collisions and then decay to visible particles inside the FASER detector, which is placed 480 m downstream of the ATLAS interaction point, aligned with the beam collisions axis. FASER also includes a sub-detector, FASER$ν$, designed to detect neutrinos produced in the LHC collisions and to study their properties. In this paper, each component of the FASER detector is described in detail, as well as the installation of the experiment system and its commissioning using cosmic-rays collected in September 2021 and during the LHC pilot beam test carried out in October 2021. FASER will start taking LHC collision data in 2022, and will run throughout LHC Run 3. △ Less

Submitted 23 July, 2022; originally announced July 2022.

Comments: 92 pages, 72 Figures

Report number: CERN-FASER-2022-001

Journal ref: JINST 19 (2024) P05066

The tracking detector of the FASER experiment

Authors: FASER Collaboration, Henso Abreu, Claire Antel, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David W. Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Olivier Crespo-Lopez, Sergey Dmitrievsky, Monica D'Onofrio, Candan Dozen, Abdallah Ezzat, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere, Stephen Gibson, Sergio Gonzalez-Sevilla , et al. (55 additional authors not shown)

Abstract: FASER is a new experiment designed to search for new light weakly-interacting long-lived particles (LLPs) and study high-energy neutrino interactions in the very forward region of the LHC collisions at CERN. The experimental apparatus is situated 480 m downstream of the ATLAS interaction-point aligned with the beam collision axis. The FASER detector includes four identical tracker stations constru… ▽ More FASER is a new experiment designed to search for new light weakly-interacting long-lived particles (LLPs) and study high-energy neutrino interactions in the very forward region of the LHC collisions at CERN. The experimental apparatus is situated 480 m downstream of the ATLAS interaction-point aligned with the beam collision axis. The FASER detector includes four identical tracker stations constructed from silicon microstrip detectors. Three of the tracker stations form a tracking spectrometer, and enable FASER to detect the decay products of LLPs decaying inside the apparatus, whereas the fourth station is used for the neutrino analysis. The spectrometer has been installed in the LHC complex since March 2021, while the fourth station is not yet installed. FASER will start physics data taking when the LHC resumes operation in early 2022. This paper describes the design, construction and testing of the tracking spectrometer, including the associated components such as the mechanics, readout electronics, power supplies and cooling system. △ Less

Submitted 31 May, 2022; v1 submitted 2 December, 2021; originally announced December 2021.

Journal ref: Nucl. Instrum. Methods Phys. Res., A 1034 (2022) 166825

The trigger and data acquisition system of the FASER experiment

Authors: FASER Collaboration, Henso Abreu, Elham Amin Mansour, Claire Antel, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Stephane Debieux, Sergey Dmitrievsky, Monica D'Onofrio, Candan Dozen, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere, Enrico Gamberini, Edward Karl Galantay , et al. (59 additional authors not shown)

Abstract: The FASER experiment is a new small and inexpensive experiment that is placed 480 meters downstream of the ATLAS experiment at the CERN LHC. FASER is designed to capture decays of new long-lived particles, produced outside of the ATLAS detector acceptance. These rare particles can decay in the FASER detector together with about 500-1000 Hz of other particles originating from the ATLAS interaction… ▽ More The FASER experiment is a new small and inexpensive experiment that is placed 480 meters downstream of the ATLAS experiment at the CERN LHC. FASER is designed to capture decays of new long-lived particles, produced outside of the ATLAS detector acceptance. These rare particles can decay in the FASER detector together with about 500-1000 Hz of other particles originating from the ATLAS interaction point. A very high efficiency trigger and data acquisition system is required to ensure that the physics events of interest will be recorded. This paper describes the trigger and data acquisition system of the FASER experiment and presents performance results of the system acquired during initial commissioning. △ Less

Submitted 10 January, 2022; v1 submitted 28 October, 2021; originally announced October 2021.

Journal ref: 2021_JINST_16_P12028

Beam test results of IHEP-NDL Low Gain Avalanche Detectors(LGAD)

Authors: S. Xiao, S. Alderweireldt, S. Ali, C. Allaire, C. Agapopoulou, N. Atanov, M. K. Ayoub, G. Barone, D. Benchekroun, A. Buzatu, D. Caforio, L. Castillo García, Y. Chan, H. Chen, V. Cindro, L. Ciucu, J. Barreiro Guimarães da Costa, H. Cui, F. Davó Miralles, Y. Davydov, G. d'Amen, C. de la Taille, R. Kiuchi, Y. Fan, A. Falou , et al. (75 additional authors not shown)

Abstract: To meet the timing resolution requirement of up-coming High Luminosity LHC (HL-LHC), a new detector based on the Low-Gain Avalanche Detector(LGAD), High-Granularity Timing Detector (HGTD), is under intensive research in ATLAS. Two types of IHEP-NDL LGADs(BV60 and BV170) for this update is being developed by Institute of High Energy Physics (IHEP) of Chinese Academic of Sciences (CAS) cooperated wi… ▽ More To meet the timing resolution requirement of up-coming High Luminosity LHC (HL-LHC), a new detector based on the Low-Gain Avalanche Detector(LGAD), High-Granularity Timing Detector (HGTD), is under intensive research in ATLAS. Two types of IHEP-NDL LGADs(BV60 and BV170) for this update is being developed by Institute of High Energy Physics (IHEP) of Chinese Academic of Sciences (CAS) cooperated with Novel Device Laboratory (NDL) of Bei**g Normal University and they are now under detailed study. These detectors are tested with $5GeV$ electron beam at DESY. A SiPM detector is chosen as a reference detector to get the timing resolution of LGADs. The fluctuation of time difference between LGAD and SiPM is extracted by fitting with a Gaussian function. Constant fraction discriminator (CFD) method is used to mitigate the effect of time walk. The timing resolution of $41 \pm 1 ps$ and $63 \pm 1 ps$ are obtained for BV60 and BV170 respectively. △ Less

Submitted 14 May, 2020; originally announced May 2020.

Radiation Campaign of HPK Prototype LGAD sensors for the High-Granularity Timing Detector (HGTD)

Authors: X. Shi, M. K. Ayoub, J. Barreiro Guimarães da Costa, H. Cui, R. Kiuchi, Y. Fan, S. Han, Y. Huang, M. **g, Z. Liang, B. Liu, J. Liu, F. Lyu, B. Qi, K. Ran, L. Shan, L. Shi, Y. Tan, K. Wu, S. Xiao, T. Yang, Y. Yang, C. Yu, M. Zhao, X. Zhuang , et al. (52 additional authors not shown)

Abstract: We report on the results of a radiation campaign with neutrons and protons of Low Gain Avalanche Detectors (LGAD) produced by Hamamatsu (HPK) as prototypes for the High-Granularity Timing Detector (HGTD) in ATLAS. Sensors with an active thickness of 50~$μ$m were irradiated in steps of roughly 2$\times$ up to a fluence of $3\times10^{15}~\mathrm{n_{eq}cm^{-2}}$. As a function of the fluence, the co… ▽ More We report on the results of a radiation campaign with neutrons and protons of Low Gain Avalanche Detectors (LGAD) produced by Hamamatsu (HPK) as prototypes for the High-Granularity Timing Detector (HGTD) in ATLAS. Sensors with an active thickness of 50~$μ$m were irradiated in steps of roughly 2$\times$ up to a fluence of $3\times10^{15}~\mathrm{n_{eq}cm^{-2}}$. As a function of the fluence, the collected charge and time resolution of the irradiated sensors will be reported for operation at $-30^{\circ}$. △ Less

Submitted 28 April, 2020; originally announced April 2020.

Layout and Performance of HPK Prototype LGAD Sensors for the High-Granularity Timing Detector

Authors: X. Yang, S. Alderweireldt, N. Atanov, M. K. Ayoub, J. Barreiro Guimaraes da Costa, L. Castillo Garcia, H. Chen, S. Christie, V. Cindro, H. Cui, G. D'Amen, Y. Davydov, Y. Y. Fan, Z. Galloway, J. J. Ge, C. Gee, G. Giacomini, E. L. Gkougkousis, C. Grieco, S. Grinstein, J. Grosse-Knetter, S. Guindon, S. Han, A. Howard, Y. P. Huang , et al. (54 additional authors not shown)

Abstract: The High-Granularity Timing Detector is a detector proposed for the ATLAS Phase II upgrade. The detector, based on the Low-Gain Avalanche Detector (LGAD) technology will cover the pseudo-rapidity region of $2.4<|η|<4.0$ with two end caps on each side and a total area of 6.4 $m^2$. The timing performance can be improved by implanting an internal gain layer that can produce signal with a fast rising… ▽ More The High-Granularity Timing Detector is a detector proposed for the ATLAS Phase II upgrade. The detector, based on the Low-Gain Avalanche Detector (LGAD) technology will cover the pseudo-rapidity region of $2.4<|η|<4.0$ with two end caps on each side and a total area of 6.4 $m^2$. The timing performance can be improved by implanting an internal gain layer that can produce signal with a fast rising edge, which improve significantly the signal-to-noise ratio. The required average timing resolution per track for a minimum-ionising particle is 30 ps at the start and 50 ps at the end of the HL-LHC operation. This is achieved with several layers of LGAD. The innermost region of the detector would accumulate a 1 MeV-neutron equivalent fluence up to $2.5 \times 10^{15} cm^{-2}$ before being replaced during the scheduled shutdowns. The addition of this new detector is expected to play an important role in the mitigation of high pile-up at the HL-LHC. The layout and performance of the various versions of LGAD prototypes produced by Hamamatsu (HPK) have been studied by the ATLAS Collaboration. The breakdown voltages, depletion voltages, inter-pad gaps, collected charge as well as the time resolution have been measured and the production yield of large size sensors has been evaluated. △ Less

Submitted 31 March, 2020; originally announced March 2020.

Comments: 17 pages, 20 figures