-
Studying single-electron traps in newly fabricated Skipper-CCDs for the Oscura experiment using the pocket-pum** technique
Authors:
S. E. Perez,
B. A. Cervantes-Vergara,
J. Estrada,
S. Holland,
D. Rodrigues,
J. Tiffenberg
Abstract:
Understanding and characterizing very low-energy ($\sim$eV) background sources is a must in rare-event searches. Oscura, an experiment aiming to probe electron recoils from sub-GeV dark matter using a 10-kg skipper-CCD detector, has recently fabricated its first two batches of sensors. In this work, we present the characterization of defects/contaminants identified in the buried-channel region of…
▽ More
Understanding and characterizing very low-energy ($\sim$eV) background sources is a must in rare-event searches. Oscura, an experiment aiming to probe electron recoils from sub-GeV dark matter using a 10-kg skipper-CCD detector, has recently fabricated its first two batches of sensors. In this work, we present the characterization of defects/contaminants identified in the buried-channel region of these newly fabricated skipper-CCDs. These defects/contaminants produce deferred charge from trap emission in the images next to particle tracks, which can be spatially resolved due to the sub-electron resolution achieved with these sensors. Using the trap-pum** technique, we measured the energy and cross section associated to these traps in three Oscura prototype sensors from different fabrication batches which underwent different gettering methods during fabrication. Results suggest that the type of defects/contaminants is more closely linked to the fabrication batch rather than to the gettering method used. The exposure-dependent single-electron rate (SER) of one of these sensors was measured $\sim$100~m underground, yielding $(1.8\pm 0.3)\times10^{-3}~e^-$/pix/day at 131K. The impact of the identified traps on the measured exposure-dependent SER is evaluated via a Monte Carlo simulation. Results suggest that the exposure-dependent SER of Oscura prototype sensors would be lower in lower background environments as expected.
△ Less
Submitted 26 June, 2024;
originally announced June 2024.
-
Search for reactor-produced millicharged particles with Skipper-CCDs at the CONNIE and Atucha-II experiments
Authors:
Alexis A. Aguilar-Arevalo,
Nicolas Avalos,
Pablo Bellino,
Xavier Bertou,
Carla Bonifazi,
Ana Botti,
Mariano Cababié,
Gustavo Cancelo,
Brenda A. Cervantes-Vergara,
Claudio Chavez,
Fernando Chierchie,
David Delgado,
Eliana Depaoli,
Juan Carlos D'Olivo,
João dos Anjos,
Juan Estrada,
Guillermo Fernandez Moroni,
Aldo R. Fernandes Neto,
Richard Ford,
Ben Kilminster,
Kevin Kuk,
Andrew Lathrop,
Patrick Lemos,
Herman P. Lima Jr.,
Martin Makler
, et al. (15 additional authors not shown)
Abstract:
Millicharged particles, proposed by various extensions of the standard model, can be created in pairs by high-energy photons within nuclear reactors and can interact electromagnetically with electrons in matter. Recently, the existence of a plasmon peak in the interaction cross-section with silicon in the eV range was highlighted as a promising approach to enhance low-energy sensitivities. The CON…
▽ More
Millicharged particles, proposed by various extensions of the standard model, can be created in pairs by high-energy photons within nuclear reactors and can interact electromagnetically with electrons in matter. Recently, the existence of a plasmon peak in the interaction cross-section with silicon in the eV range was highlighted as a promising approach to enhance low-energy sensitivities. The CONNIE and Atucha-II reactor neutrino experiments utilize Skipper-CCD sensors, which enable the detection of interactions in the eV range. We present world-leading limits on the charge of millicharged particles within a mass range spanning six orders of magnitude, derived through a comprehensive analysis and the combination of data from both experiments.
△ Less
Submitted 25 May, 2024;
originally announced May 2024.
-
Deployment and performance of a Low-Energy-Threshold Skipper-CCD inside a nuclear reactor
Authors:
E. Depaoli,
D. Rodrigues,
I. Sidelnik,
P. Bellino,
A. Botti,
D. Delgado,
M. Cababie,
F. Chierchie,
J. Estrada,
G. Fernandez Moroni,
S. Perez,
J. Tiffenberg
Abstract:
Charge Coupled Devices (CCD) are used for reactor neutrino experiments and already shown their potential in constraining new physics models. The prospect of a Skipper-CCD experiment looking for standard and beyond standard model physics (BSM) in a nuclear reactor has been recently evaluated for different benchmark scenarios. Here we report the installation of the first 2 g Skipper-CCD inside the c…
▽ More
Charge Coupled Devices (CCD) are used for reactor neutrino experiments and already shown their potential in constraining new physics models. The prospect of a Skipper-CCD experiment looking for standard and beyond standard model physics (BSM) in a nuclear reactor has been recently evaluated for different benchmark scenarios. Here we report the installation of the first 2 g Skipper-CCD inside the containment building of a 2 GW$_{th}$ nuclear power plant, positioned 12 meters from the center of the reactor core. We discuss the challenges involved in the commissioning of the detector and present data acquired during reactor ON and reactor OFF periods, with the detector operating with a sub-electron readout noise of 0.17 e-. The ongoing efforts to improve sensitivities to CEvNS and BSM interaction are also discussed.
△ Less
Submitted 7 March, 2024; v1 submitted 15 January, 2024;
originally announced January 2024.
-
SENSEI: First Direct-Detection Results on sub-GeV Dark Matter from SENSEI at SNOLAB
Authors:
SENSEI Collaboration,
Prakruth Adari,
Itay M. Bloch,
Ana M. Botti,
Mariano Cababie,
Gustavo Cancelo,
Brenda A. Cervantes-Vergara,
Michael Crisler,
Miguel Daal,
Ansh Desai,
Alex Drlica-Wagner,
Rouven Essig,
Juan Estrada,
Erez Etzion,
Guillermo Fernandez Moroni,
Stephen E. Holland,
Yonatan Kehat,
Yaron Korn,
Ian Lawson,
Steffon Luoma,
Aviv Orly,
Santiago E. Perez,
Dario Rodrigues,
Nathan A. Saffold,
Silvia Scorza
, et al. (12 additional authors not shown)
Abstract:
We present the first results from a dark matter search using six Skipper-CCDs in the SENSEI detector operating at SNOLAB. With an exposure of 534.9 gram-days from well-performing sensors, we select events containing 2 to 10 electron-hole pairs. After aggressively masking images to remove backgrounds, we observe 55 two-electron events, 4 three-electron events, and no events containing 4 to 10 elect…
▽ More
We present the first results from a dark matter search using six Skipper-CCDs in the SENSEI detector operating at SNOLAB. With an exposure of 534.9 gram-days from well-performing sensors, we select events containing 2 to 10 electron-hole pairs. After aggressively masking images to remove backgrounds, we observe 55 two-electron events, 4 three-electron events, and no events containing 4 to 10 electrons. The two-electron events are consistent with pileup from one-electron events. Among the 4 three-electron events, 2 appear in pixels that are likely impacted by detector defects, although not strongly enough to trigger our "hot-pixel" mask. We use these data to set world-leading constraints on sub-GeV dark matter interacting with electrons and nuclei.
△ Less
Submitted 20 December, 2023;
originally announced December 2023.
-
Physics Opportunities at a Beam Dump Facility at PIP-II at Fermilab and Beyond
Authors:
A. A. Aguilar-Arevalo,
J. L. Barrow,
C. Bhat,
J. Bogenschuetz,
C. Bonifazi,
A. Bross,
B. Cervantes,
J. D'Olivo,
A. De Roeck,
B. Dutta,
M. Eads,
J. Eldred,
J. Estrada,
A. Fava,
C. Fernandes Vilela,
G. Fernandez Moroni,
B. Flaugher,
S. Gardiner,
G. Gurung,
P. Gutierrez,
W. Y. Jang,
K. J. Kelly,
D. Kim,
T. Kobilarcik,
Z. Liu
, et al. (23 additional authors not shown)
Abstract:
The Fermilab Proton-Improvement-Plan-II (PIP-II) is being implemented in order to support the precision neutrino oscillation measurements at the Deep Underground Neutrino Experiment, the U.S. flagship neutrino experiment. The PIP-II LINAC is presently under construction and is expected to provide 800~MeV protons with 2~mA current. This white paper summarizes the outcome of the first workshop on Ma…
▽ More
The Fermilab Proton-Improvement-Plan-II (PIP-II) is being implemented in order to support the precision neutrino oscillation measurements at the Deep Underground Neutrino Experiment, the U.S. flagship neutrino experiment. The PIP-II LINAC is presently under construction and is expected to provide 800~MeV protons with 2~mA current. This white paper summarizes the outcome of the first workshop on May 10 through 13, 2023, to exploit this capability for new physics opportunities in the kinematic regime that are unavailable to other facilities, in particular a potential beam dump facility implemented at the end of the LINAC. Various new physics opportunities have been discussed in a wide range of kinematic regime, from eV scale to keV and MeV. We also emphasize that the timely establishment of the beam dump facility at Fermilab is essential to exploit these new physics opportunities.
△ Less
Submitted 16 November, 2023;
originally announced November 2023.
-
SENSEI: Search for Millicharged Particles produced in the NuMI Beam
Authors:
Liron Barak,
Itay M. Bloch,
Ana M. Botti,
Mariano Cababie,
Gustavo Cancelo,
Luke Chaplinsky,
Michael Crisler,
Alex Drlica-Wagner,
Rouven Essig,
Juan Estrada,
Erez Etzion,
Guillermo Fernandez Moroni,
Roni Harnik,
Stephen E. Holland,
Yaron Korn,
Zhen Liu,
Sravan Munagavalasa,
Aviv Orly,
Santiago E. Perez,
Ryan Plestid,
Dario Rodrigues,
Nathan A. Saffold,
Silvia Scorza,
Aman Singal,
Miguel Sofo Haro
, et al. (6 additional authors not shown)
Abstract:
Millicharged particles appear in several extensions of the Standard Model, but have not yet been detected. These hypothetical particles could be produced by an intense proton beam striking a fixed target. We use data collected in 2020 by the SENSEI experiment in the MINOS cavern at the Fermi National Accelerator Laboratory to search for ultra-relativistic millicharged particles produced in collisi…
▽ More
Millicharged particles appear in several extensions of the Standard Model, but have not yet been detected. These hypothetical particles could be produced by an intense proton beam striking a fixed target. We use data collected in 2020 by the SENSEI experiment in the MINOS cavern at the Fermi National Accelerator Laboratory to search for ultra-relativistic millicharged particles produced in collisions of protons in the NuMI beam with a fixed graphite target. The absence of any ionization events with 3 to 6 electrons in the SENSEI data allow us to place world-leading constraints on millicharged particles for masses between 30 MeV to 380 MeV. This work also demonstrates the potential of utilizing low-threshold detectors to investigate new particles in beam-dump experiments, and motivates a future experiment designed specifically for this purpose.
△ Less
Submitted 24 May, 2023; v1 submitted 8 May, 2023;
originally announced May 2023.
-
Searching for millicharged particles with 1 kg of Skipper-CCDs using the NuMI beam at Fermilab
Authors:
Santiago Perez,
Dario Rodrigues,
Juan Estrada,
Roni Harnik,
Zhen Liu,
Brenda A. Cervantes-Vergara,
Juan Carlos D'Olivo,
Ryan D. Plestid,
Javier Tiffenberg,
Tien-Tien Yu,
Alexis Aguilar-Arevalo,
Fabricio Alcalde-Bessia,
Nicolas Avalos,
Oscar Baez,
Daniel Baxter,
Xavier Bertou,
Carla Bonifazi,
Ana Botti,
Gustavo Cancelo,
Nuria Castelló-Mor,
Alvaro E. Chavarria,
Claudio R. Chavez,
Fernando Chierchie,
Juan Manuel De Egea,
Cyrus Dreyer
, et al. (35 additional authors not shown)
Abstract:
Oscura is a planned light-dark matter search experiment using Skipper-CCDs with a total active mass of 10 kg. As part of the detector development, the collaboration plans to build the Oscura Integration Test (OIT), an engineering test with 10% of the total mass. Here we discuss the early science opportunities with the OIT to search for millicharged particles (mCPs) using the NuMI beam at Fermilab.…
▽ More
Oscura is a planned light-dark matter search experiment using Skipper-CCDs with a total active mass of 10 kg. As part of the detector development, the collaboration plans to build the Oscura Integration Test (OIT), an engineering test with 10% of the total mass. Here we discuss the early science opportunities with the OIT to search for millicharged particles (mCPs) using the NuMI beam at Fermilab. mCPs would be produced at low energies through photon-mediated processes from decays of scalar, pseudoscalar, and vector mesons, or direct Drell-Yan productions. Estimates show that the OIT would be a world-leading probe for mCPs in the MeV mass range.
△ Less
Submitted 2 December, 2023; v1 submitted 17 April, 2023;
originally announced April 2023.
-
Skipper-CCD Sensors for the Oscura Experiment: Requirements and Preliminary Tests
Authors:
Brenda A. Cervantes-Vergara,
Santiago Perez,
Juan Estrada,
Ana Botti,
Claudio R. Chavez,
Fernando Chierchie,
Nathan Saffold,
Alexis Aguilar-Arevalo,
Fabricio Alcalde-Bessia,
Nicolás Avalos,
Oscar Baez,
Daniel Baxter,
Xavier Bertou,
Carla Bonifazi,
Gustavo Cancelo,
Nuria Castelló-Mor,
Alvaro E. Chavarria,
Juan Manuel De Egea,
Juan Carlos D'Olivo,
Cyrus Dreyer,
Alex Drlica-Wagner,
Rouven Essig,
Ezequiel Estrada,
Erez Etzion,
Paul Grylls
, et al. (30 additional authors not shown)
Abstract:
Oscura is a proposed multi-kg skipper-CCD experiment designed for a dark matter (DM) direct detection search that will reach unprecedented sensitivity to sub-GeV DM-electron interactions with its 10 kg detector array. Oscura is planning to operate at SNOLAB with 2070 m overburden, and aims to reach a background goal of less than one event in each electron bin in the 2-10 electron ionization-signal…
▽ More
Oscura is a proposed multi-kg skipper-CCD experiment designed for a dark matter (DM) direct detection search that will reach unprecedented sensitivity to sub-GeV DM-electron interactions with its 10 kg detector array. Oscura is planning to operate at SNOLAB with 2070 m overburden, and aims to reach a background goal of less than one event in each electron bin in the 2-10 electron ionization-signal region for the full 30 kg-year exposure, with a radiation background rate of 0.01 dru. In order to achieve this goal, Oscura must address each potential source of background events, including instrumental backgrounds. In this work, we discuss the main instrumental background sources and the strategy to control them, establishing a set of constraints on the sensors' performance parameters. We present results from the tests of the first fabricated Oscura prototype sensors, evaluate their performance in the context of the established constraints and estimate the Oscura instrumental background based on these results.
△ Less
Submitted 11 April, 2024; v1 submitted 10 April, 2023;
originally announced April 2023.
-
Adaptive weighting of Bayesian physics informed neural networks for multitask and multiscale forward and inverse problems
Authors:
Sarah Perez,
Suryanarayana Maddu,
Ivo F. Sbalzarini,
Philippe Poncet
Abstract:
In this paper, we present a novel methodology for automatic adaptive weighting of Bayesian Physics-Informed Neural Networks (BPINNs), and we demonstrate that this makes it possible to robustly address multi-objective and multi-scale problems. BPINNs are a popular framework for data assimilation, combining the constraints of Uncertainty Quantification (UQ) and Partial Differential Equation (PDE). T…
▽ More
In this paper, we present a novel methodology for automatic adaptive weighting of Bayesian Physics-Informed Neural Networks (BPINNs), and we demonstrate that this makes it possible to robustly address multi-objective and multi-scale problems. BPINNs are a popular framework for data assimilation, combining the constraints of Uncertainty Quantification (UQ) and Partial Differential Equation (PDE). The relative weights of the BPINN target distribution terms are directly related to the inherent uncertainty in the respective learning tasks. Yet, they are usually manually set a-priori, that can lead to pathological behavior, stability concerns, and to conflicts between tasks which are obstacles that have deterred the use of BPINNs for inverse problems with multi-scale dynamics. The present weighting strategy automatically tunes the weights by considering the multi-task nature of target posterior distribution. We show that this remedies the failure modes of BPINNs and provides efficient exploration of the optimal Pareto front. This leads to better convergence and stability of BPINN training while reducing sampling bias. The determined weights moreover carry information about task uncertainties, reflecting noise levels in the data and adequacy of the PDE model. We demonstrate this in numerical experiments in Sobolev training, and compare them to analytically $ε$-optimal baseline, and in a multi-scale Lokta-Volterra inverse problem. We eventually apply this framework to an inpainting task and an inverse problem, involving latent field recovery for incompressible flow in complex geometries.
△ Less
Submitted 24 February, 2023;
originally announced February 2023.
-
First results from a multiplexed and massive instrument with sub-electron noise Skipper-CCDs
Authors:
F. Chierchie,
C. R. Chavez,
M. Sofo Haro,
G. Fernandez Moroni,
B. A. Cervantes-Vergara,
S. Perez,
J. Estrada,
J. Tiffenberg,
S. Uemura,
A. Botti
Abstract:
We present a new instrument composed of a large number of sub-electron noise Skipper-CCDs operated with a two stage analog multiplexed readout scheme suitable for scaling to thousands of channels. New, thick, $1.35$ Mpix sensors, from a new foundry, are glued into a Multi-Chip Module (MCM) printed circuit board on a ceramic substrate which has 16 sensors each. The instrument, that can hold up-to 1…
▽ More
We present a new instrument composed of a large number of sub-electron noise Skipper-CCDs operated with a two stage analog multiplexed readout scheme suitable for scaling to thousands of channels. New, thick, $1.35$ Mpix sensors, from a new foundry, are glued into a Multi-Chip Module (MCM) printed circuit board on a ceramic substrate which has 16 sensors each. The instrument, that can hold up-to 16 MCMs, a total of 256 Skipper-CCD sensors (called a Super-Module with $\approx 130$ grams of active mass and $346$ Mpix), is part of the R$\&$D effort of the OSCURA experiment which will have $\approx 94$ super-modules. Experimental results with $10$ MCMs and $160$ Skipper-CCDs sensors are presented in this paper. This is already the largest ever build instrument with single electron sensitivity CCDs using nondestructive readout, both, in terms of active mass and number of channels.
△ Less
Submitted 2 November, 2022; v1 submitted 28 October, 2022;
originally announced October 2022.
-
Skipper-CCDs: current applications and future
Authors:
B. A. Cervantes-Vergara,
S. Perez,
J. C. D'Olivo,
J. Estrada,
D. J. Grimm,
S. Holland,
M. Sofo-Haro,
W. Wong
Abstract:
This work briefly discusses the potential applications of the Skipper-CCD technology in astronomy and reviews its current use in dark matter and neutrino experiments. An overview of the ongoing efforts to build multi-kilogram experiments with these sensors is given, in the context of the Oscura experiment. First results from the characterization of Oscura sensors from the first 200 mm wafer-fabric…
▽ More
This work briefly discusses the potential applications of the Skipper-CCD technology in astronomy and reviews its current use in dark matter and neutrino experiments. An overview of the ongoing efforts to build multi-kilogram experiments with these sensors is given, in the context of the Oscura experiment. First results from the characterization of Oscura sensors from the first 200 mm wafer-fabrication run with a new vendor are presented. The overall yield of the electron counting capability of these sensors is 71%. A noise of 0.087 e$^-$ RMS, with 1225 samples/pix, and a dark current of (0.031$\pm$0.013) e$^-$/pix/day at 140 K were measured.
△ Less
Submitted 10 August, 2022;
originally announced August 2022.
-
Unconditional bound-preserving and energy-dissipating finite-volume schemes for the Cahn-Hilliard equation
Authors:
Rafael Bailo,
José A. Carrillo,
Serafim Kalliadasis,
Sergio P. Perez
Abstract:
We propose finite-volume schemes for the Cahn-Hilliard equation which unconditionally and discretely preserve the boundedness of the phase field and the dissipation of the free energy. Our numerical framework is applicable to a variety of free-energy potentials, including Ginzburg-Landau and Flory-Huggins, to general wetting boundary conditions, and to degenerate mobilities. Its central thrust is…
▽ More
We propose finite-volume schemes for the Cahn-Hilliard equation which unconditionally and discretely preserve the boundedness of the phase field and the dissipation of the free energy. Our numerical framework is applicable to a variety of free-energy potentials, including Ginzburg-Landau and Flory-Huggins, to general wetting boundary conditions, and to degenerate mobilities. Its central thrust is the upwind methodology, which we combine with a semi-implicit formulation for the free-energy terms based on the classical convex-splitting approach. The extension of the schemes to an arbitrary number of dimensions is straightforward thanks to their dimensionally split nature, which allows to efficiently solve higher-dimensional problems with a simple parallelisation. The numerical schemes are validated and tested through a variety of examples, in different dimensions, and with various contact angles between droplets and substrates.
△ Less
Submitted 17 February, 2023; v1 submitted 11 May, 2021;
originally announced May 2021.
-
A Review of Gas-Surface Interaction Models for Orbital Aerodynamics Applications
Authors:
Sabrina Livadiotti,
Nicholas H. Crisp,
Peter C. E. Roberts,
Stephen D. Worrall,
Vitor T. A. Oiko,
Steve Edmondson,
Sarah J. Haigh,
Claire Huyton,
Katharine L. Smith,
Luciana A. Sinpetru,
Brandon E. A. Holmes,
Jonathan Becedas,
Rosa María Domínguez,
Valentín Cañas,
Simon Christensen,
Anders Mølgaard,
Jens Nielsen,
Morten Bisgaard,
Yung-An Chan,
Georg H. Herdrich,
Francesco Romano,
Stefanos Fasoulas,
Constantin Traub,
Daniel Garcia-Almiñana,
Silvia Rodriguez-Donaire
, et al. (7 additional authors not shown)
Abstract:
Renewed interest in Very Low Earth Orbits (VLEO) - i.e. altitudes below 450 km - has led to an increased demand for accurate environment characterisation and aerodynamic force prediction. While the former requires knowledge of the mechanisms that drive density variations in the thermosphere, the latter also depends on the interactions between the gas-particles in the residual atmosphere and the su…
▽ More
Renewed interest in Very Low Earth Orbits (VLEO) - i.e. altitudes below 450 km - has led to an increased demand for accurate environment characterisation and aerodynamic force prediction. While the former requires knowledge of the mechanisms that drive density variations in the thermosphere, the latter also depends on the interactions between the gas-particles in the residual atmosphere and the surfaces exposed to the flow. The determination of the aerodynamic coefficients is hindered by the numerous uncertainties that characterise the physical processes occurring at the exposed surfaces. Several models have been produced over the last 60 years with the intent of combining accuracy with relatively simple implementations. In this paper the most popular models have been selected and reviewed using as discriminating factors relevance with regards to orbital aerodynamics applications and theoretical agreement with gas-beam experimental data. More sophisticated models were neglected, since their increased accuracy is generally accompanied by a substantial increase in computation times which is likely to be unsuitable for most space engineering applications. For the sake of clarity, a distinction was introduced between physical and scattering kernel theory based gas-surface interaction models. The physical model category comprises the Hard Cube model, the Soft Cube model and the Washboard model, while the scattering kernel family consists of the Maxwell model, the Nocilla-Hurlbut-Sherman model and the Cercignani-Lampis-Lord model. Limits and assets of each model have been discussed with regards to the context of this paper. Wherever possible, comments have been provided to help the reader to identify possible future challenges for gas-surface interaction science with regards to orbital aerodynamic applications.
△ Less
Submitted 22 November, 2020; v1 submitted 1 October, 2020;
originally announced October 2020.
-
The Benefits of Very Low Earth Orbit for Earth Observation Missions
Authors:
N. H. Crisp,
P. C. E. Roberts,
S. Livadiotti,
V. T. A. Oiko,
S. Edmondson,
S. J. Haigh,
C. Huyton,
L. Sinpetru,
K. L. Smith,
S. D. Worrall,
J. Becedas,
R. M. Domínguez,
D. González,
V. Hanessian,
A. Mølgaard,
J. Nielsen,
M. Bisgaard,
Y. -A. Chan,
S. Fasoulas,
G. H. Herdrich,
F. Romano,
C. Traub,
D. García-Almiñana,
S. Rodríguez-Donaire,
M. Sureda
, et al. (8 additional authors not shown)
Abstract:
Very low Earth orbits (VLEO), typically classified as orbits below approximately 450 km in altitude, have the potential to provide significant benefits to spacecraft over those that operate in higher altitude orbits. This paper provides a comprehensive review and analysis of these benefits to spacecraft operations in VLEO, with parametric investigation of those which apply specifically to Earth ob…
▽ More
Very low Earth orbits (VLEO), typically classified as orbits below approximately 450 km in altitude, have the potential to provide significant benefits to spacecraft over those that operate in higher altitude orbits. This paper provides a comprehensive review and analysis of these benefits to spacecraft operations in VLEO, with parametric investigation of those which apply specifically to Earth observation missions. The most significant benefit for optical imaging systems is that a reduction in orbital altitude improves spatial resolution for a similar payload specification. Alternatively mass and volume savings can be made whilst maintaining a given performance. Similarly, for radar and lidar systems, the signal-to-noise ratio can be improved. Additional benefits include improved geospatial position accuracy, improvements in communications link-budgets, and greater launch vehicle insertion capability. The collision risk with orbital debris and radiation environment can be shown to be improved in lower altitude orbits, whilst compliance with IADC guidelines for spacecraft post-mission lifetime and deorbit is also assisted. Finally, VLEO offers opportunities to exploit novel atmosphere-breathing electric propulsion systems and aerodynamic attitude and orbit control methods.
However, key challenges associated with our understanding of the lower thermosphere, aerodynamic drag, the requirement to provide a meaningful orbital lifetime whilst minimising spacecraft mass and complexity, and atomic oxygen erosion still require further research. Given the scope for significant commercial, societal, and environmental impact which can be realised with higher performing Earth observation platforms, renewed research efforts to address the challenges associated with VLEO operations are required.
△ Less
Submitted 16 July, 2020; v1 submitted 15 July, 2020;
originally announced July 2020.
-
RF Helicon-based Inductive Plasma Thruster (IPT) Design for an Atmosphere-Breathing Electric Propulsion system (ABEP)
Authors:
Francesco Romano,
Yung-An Chan,
Georg Herdrich,
Peter C. E. Roberts,
C. Traub S. Fasoulas,
K. Smith,
S. Edmondson,
S. Haigh,
N. H. Crisp,
V. T. A. Oiko,
S. D. Worrall,
S. Livadiotti,
C. Huyton,
L. A. Sinpetru,
A. Straker,
J. Becedas,
R. M. Domínguez,
D. González,
V. Cañas,
V. Sulliotti-Linner,
V. Hanessian,
A. Mølgaard,
J. Nielsen,
M. Bisgaard,
D. Garcia-Almiñana
, et al. (10 additional authors not shown)
Abstract:
Challenging space missions include those at very low altitudes, where the atmosphere is source of aerodynamic drag on the spacecraft. To extend such missions lifetime, an efficient propulsion system is required. One solution is Atmosphere-Breathing Electric Propulsion (ABEP). It collects atmospheric particles to be used as propellant for an electric thruster. The system would minimize the requirem…
▽ More
Challenging space missions include those at very low altitudes, where the atmosphere is source of aerodynamic drag on the spacecraft. To extend such missions lifetime, an efficient propulsion system is required. One solution is Atmosphere-Breathing Electric Propulsion (ABEP). It collects atmospheric particles to be used as propellant for an electric thruster. The system would minimize the requirement of limited propellant availability and can also be applied to any planet with atmosphere, enabling new mission at low altitude ranges for longer times. Challenging is also the presence of reactive chemical species, such as atomic oxygen in Earth orbit. Such species cause erosion of (not only) propulsion system components, i.e. acceleration grids, electrodes, and discharge channels of conventional EP systems. IRS is develo** within the DISCOVERER project, an intake and a thruster for an ABEP system. The paper describes the design and implementation of the RF helicon-based inductive plasma thruster (IPT). This paper deals in particular with the design and implementation of a novel antenna called the birdcage antenna, a device well known in magnetic resonance imaging (MRI), and also lately employed for helicon-wave based plasma sources in fusion research. The IPT is based on RF electrodeless operation aided by an externally applied static magnetic field. The IPT is composed by an antenna, a discharge channel, a movable injector, and a solenoid. By changing the operational parameters along with the novel antenna design, the aim is to minimize losses in the RF circuit, and accelerate a quasi-neutral plasma plume. This is also to be aided by the formation of helicon waves within the plasma that are to improve the overall efficiency and achieve higher exhaust velocities. Finally, the designed IPT with a particular focus on the birdcage antenna design procedure is presented
△ Less
Submitted 14 July, 2020; v1 submitted 13 July, 2020;
originally announced July 2020.
-
High-order well-balanced finite volume schemes for hydrodynamic equations with nonlocal free energy
Authors:
José A. Carrillo,
Manuel J. Castro,
Serafim Kalliadasis,
Sergio P. Perez
Abstract:
We propose high-order well-balanced finite-volume schemes for a broad class of hydrodynamic systems with attractive-repulsive interaction forces and linear and nonlinear dam**. Our schemes are suitable for free energies containing convolutions of an interaction potential with the density, which are essential for applications such as the Keller-Segel model, more general Euler-Poisson systems, or…
▽ More
We propose high-order well-balanced finite-volume schemes for a broad class of hydrodynamic systems with attractive-repulsive interaction forces and linear and nonlinear dam**. Our schemes are suitable for free energies containing convolutions of an interaction potential with the density, which are essential for applications such as the Keller-Segel model, more general Euler-Poisson systems, or dynamic-density functional theory. Our schemes are also equipped with a nonnegative-density reconstruction which allows for vacuum regions during the simulation. We provide several prototypical examples from relevant applications highlighting the benefit of our algorithms elucidate also some of our analytical results.
△ Less
Submitted 19 November, 2020; v1 submitted 11 April, 2020;
originally announced April 2020.
-
The Artscience of Planet Formation: import ArtScience.PlanetFormation as AATS
Authors:
Sebastián Pérez
Abstract:
The Art, Astronomy, Technology and Society (AATS) project is an artscience collaboration which dwells in the inbetweenness layer of scientific understanding of the origins of planets and the embodied, intuited ways of knowing. One of the oldest and at the same time one of the newest concerns of humanity is "How did the Earth and the planets come to be?". Planet formation, an intricate and potentia…
▽ More
The Art, Astronomy, Technology and Society (AATS) project is an artscience collaboration which dwells in the inbetweenness layer of scientific understanding of the origins of planets and the embodied, intuited ways of knowing. One of the oldest and at the same time one of the newest concerns of humanity is "How did the Earth and the planets come to be?". Planet formation, an intricate and potentially chaotic process, is also very efficient. Every star harbors at least one planet, as evidenced by the high frequency of exoplanet detections. Planet formation must therefore be a frequent process. Yet, learning about the origins of planets has been difficult. Here I share my experience in the AATS artscience project and discuss the nature of artscience collaborations.
△ Less
Submitted 6 January, 2020;
originally announced January 2020.
-
A Finite-Volume Method for Fluctuating Dynamical Density Functional Theory
Authors:
Antonio Russo,
Sergio P. Perez,
Miguel A. Durán-Olivencia,
Peter Yatsyshin,
José A. Carrillo,
Serafim Kalliadasis
Abstract:
We introduce a finite-volume numerical scheme for solving stochastic gradient-flow equations. Such equations are of crucial importance within the framework of fluctuating hydrodynamics and dynamic density functional theory. Our proposed scheme deals with general free-energy functionals, including, for instance, external fields or interaction potentials. This allows us to simulate a range of physic…
▽ More
We introduce a finite-volume numerical scheme for solving stochastic gradient-flow equations. Such equations are of crucial importance within the framework of fluctuating hydrodynamics and dynamic density functional theory. Our proposed scheme deals with general free-energy functionals, including, for instance, external fields or interaction potentials. This allows us to simulate a range of physical phenomena where thermal fluctuations play a crucial role, such as nucleation and other energy-barrier crossing transitions. A positivity-preserving algorithm for the density is derived based on a hybrid space discretization of the deterministic and the stochastic terms and different implicit and explicit time integrators. We show through numerous applications that not only our scheme is able to accurately reproduce the statistical properties (structure factor and correlations) of the physical system, but, because of the multiplicative noise, it allows us to simulate energy barrier crossing dynamics, which cannot be captured by mean-field approaches.
△ Less
Submitted 31 December, 2020; v1 submitted 11 October, 2019;
originally announced October 2019.
-
Well-balanced finite volume schemes for hydrodynamic equations with general free energy
Authors:
José A. Carrillo,
Serafim Kalliadasis,
Sergio P. Perez,
Chi-Wang Shu
Abstract:
Well balanced and free energy dissipative first- and second-order accurate finite volume schemes are proposed for a general class of hydrodynamic systems with linear and nonlinear dam**. The natural Liapunov functional of the system, given by its free energy, allows for a characterization of the stationary states by its variation. An analog property at the discrete level enables us to preserve s…
▽ More
Well balanced and free energy dissipative first- and second-order accurate finite volume schemes are proposed for a general class of hydrodynamic systems with linear and nonlinear dam**. The natural Liapunov functional of the system, given by its free energy, allows for a characterization of the stationary states by its variation. An analog property at the discrete level enables us to preserve stationary states at machine precision while kee** the dissipation of the discrete free energy. These schemes allow for analysing accurately the stability properties of stationary states in challeging problems such as: phase transitions in collective behavior, generalized Euler-Poisson systems in chemotaxis and astrophysics, and models in dynamic density functional theories; having done a careful validation in a battery of relevant test cases.
△ Less
Submitted 4 November, 2020; v1 submitted 3 December, 2018;
originally announced December 2018.
-
Production and Integration of the ATLAS Insertable B-Layer
Authors:
B. Abbott,
J. Albert,
F. Alberti,
M. Alex,
G. Alimonti,
S. Alkire,
P. Allport,
S. Altenheiner,
L. Ancu,
E. Anderssen,
A. Andreani,
A. Andreazza,
B. Axen,
J. Arguin,
M. Backhaus,
G. Balbi,
J. Ballansat,
M. Barbero,
G. Barbier,
A. Bassalat,
R. Bates,
P. Baudin,
M. Battaglia,
T. Beau,
R. Beccherle
, et al. (352 additional authors not shown)
Abstract:
During the shutdown of the CERN Large Hadron Collider in 2013-2014, an additional pixel layer was installed between the existing Pixel detector of the ATLAS experiment and a new, smaller radius beam pipe. The motivation for this new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the robustness and performance of the ATLAS tracking system, given the higher instantaneous and i…
▽ More
During the shutdown of the CERN Large Hadron Collider in 2013-2014, an additional pixel layer was installed between the existing Pixel detector of the ATLAS experiment and a new, smaller radius beam pipe. The motivation for this new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the robustness and performance of the ATLAS tracking system, given the higher instantaneous and integrated luminosities realised following the shutdown. Because of the extreme radiation and collision rate environment, several new radiation-tolerant sensor and electronic technologies were utilised for this layer. This paper reports on the IBL construction and integration prior to its operation in the ATLAS detector.
△ Less
Submitted 6 June, 2018; v1 submitted 2 March, 2018;
originally announced March 2018.
-
BIOSTIRLING-4SKA : A cost effective and efficient approach for a new generation of solar dish-Stirling plants based on storage and hybridization; An Energy demo project for Large Scale Infrastructures",
Authors:
Domingos Barbosa,
Paulo Andre,
Paulo Antunes,
Tiago Paixao,
Carlos Marques,
Arnold van Ardenne,
Dion Kant,
Nico Ebbendorf,
Luis Saturnino Gonzalez,
Diego Rubio,
Lourdes Verdes-Montenegro,
Emilio Garcia,
Irene Calama,
Francisco Caballero,
Per Eskilson,
Lars Gustavsson,
Conny Anderson,
Jonah Lindh,
Reinhard Keller,
Manuel Silva Perez,
Gonzalo Lobo,
Valeriano Ruiz,
Javier Pino,
Luis Valverde,
Carsten Holze
, et al. (6 additional authors not shown)
Abstract:
The BIOSTIRLING - 4SKA (B4S) is a EU demonstration project dealing with the implementation of a cost-effective and efficient new generation of solar dish-Stirling plants based on hybridization and efficient storage at the industrial scale. The main goal of the B4S demonstration project is the generation of electric power using simultaneously solar power and gas to supply an isolated system and act…
▽ More
The BIOSTIRLING - 4SKA (B4S) is a EU demonstration project dealing with the implementation of a cost-effective and efficient new generation of solar dish-Stirling plants based on hybridization and efficient storage at the industrial scale. The main goal of the B4S demonstration project is the generation of electric power using simultaneously solar power and gas to supply an isolated system and act as a scalable example of potential power supply for many infrastructures, including future sustainable large scientific infrastructures. B4S build an interdisciplinary approach to address reliability, maintainability and costs of this technology. In April 2017, B4S successfully tested in Portugal the first world Stirling hybrid system providing about 4kW of power to a phased array of antennas, overcoming challenges in Stirling and hybridization and smartgrid technologies. B4SKA Consortium, with fourteen companies from six European countries, has performed the engineering, construction, assembly and experimental exploitation, under contract signed with the European to develop on off-grid demonstrator in Contenda (Moura) Portugal.
△ Less
Submitted 11 September, 2018; v1 submitted 8 December, 2017;
originally announced December 2017.
-
Structural evolution of CO2 filled pure silica LTA zeolite under high-pressure high-temperature conditions
Authors:
David Santamaria Perez,
Tomas Marqueno,
Simon MacLeod,
Javier Ruiz Fuertes,
Dominik Daisenberger,
Raquel Chulia Jordan,
Daniel Errandonea,
Jose Luis Jorda,
Fernando Rey,
Chris McGuire,
Adam Mahkluf,
Abby Kavner,
Catalin Popescu
Abstract:
The crystal structure of CO2 filled pure SiO2 LTA zeolite has been studied at high pressures and temperatures using synchrotron based x ray powder diffraction. Its structure consists of 13 CO2 guest molecules, 12 of them accommodated in the large alpha cages and 1 in the beta cages, giving a SiO2:CO2 stoichiometric ratio smaller than 2. The structure remains stable under pressure up to 20 GPa with…
▽ More
The crystal structure of CO2 filled pure SiO2 LTA zeolite has been studied at high pressures and temperatures using synchrotron based x ray powder diffraction. Its structure consists of 13 CO2 guest molecules, 12 of them accommodated in the large alpha cages and 1 in the beta cages, giving a SiO2:CO2 stoichiometric ratio smaller than 2. The structure remains stable under pressure up to 20 GPa with a slight pressure dependent rhombohedral distortion, indicating that pressure induced amorphization is prevented by the insertion of guest species in this open framework. The ambient-temperature lattice compressibility has been determined. In situ high pressure resistive heating experiments up to 750 K allow us to estimate the thermal expansivity at 5 GPa. Our data confirm that the insertion of CO2 reverses the negative thermal expansion of the empty zeolite structure. No evidence of any chemical reaction was observed. The possibility of synthesizing a silicon carbonate at high temperatures and higher pressures is discussed in terms of the evolution of C-O and Si-O distances between molecular and framework atoms.
△ Less
Submitted 30 May, 2017;
originally announced May 2017.
-
Capturing Structural Dynamics in Crystalline Silicon Using Chirped Electrons from a Laser Wakefield Accelerator
Authors:
Z. -H He,
B. Beaurepaire,
J. A. Nees,
G. Gallé,
S. A. Scott,
J. R. Sanchez Pérez,
M. G. Lagally,
K. Krushelnick,
A. G. R. Thomas,
J. Faure
Abstract:
Recent progress in laser wakefield acceleration has led to the emergence of a new generation of electron and X-ray sources that may have enormous benefits for ultrafast science. These novel sources promise to become indispensable tools for the investigation of structural dynamics on the femtosecond time scale, with spatial resolution on the atomic scale. Here, we demonstrate the use of laser-wakef…
▽ More
Recent progress in laser wakefield acceleration has led to the emergence of a new generation of electron and X-ray sources that may have enormous benefits for ultrafast science. These novel sources promise to become indispensable tools for the investigation of structural dynamics on the femtosecond time scale, with spatial resolution on the atomic scale. Here, we demonstrate the use of laser-wakefield-accelerated electron bunches for time-resolved electron diffraction measurements of the structural dynamics of single-crystal silicon nano-membranes pumped by an ultrafast laser pulse. In our proof-of-concept study, we resolve the silicon lattice dynamics on a picosecond time scale by deflecting the momentum-time correlated electrons in the diffraction peaks with a static magnetic field to obtain the time-dependent diffraction efficiency. Further improvements may lead to femtosecond temporal resolution, with negligible pump-probe jitter being possible with future laser-wakefield-accelerator ultrafast-electron-diffraction schemes.
△ Less
Submitted 20 October, 2016;
originally announced October 2016.
-
Active learning in pre-class assignments: Exploring the use of interactive simulations to enhance reading assignments
Authors:
Jared B. Stang,
Megan Barker,
Sarah Perez,
Joss Ives,
Ido Roll
Abstract:
Pre-class reading assignments help prepare students for active classes by providing a first exposure to the terms and concepts to be used during class. We investigate if the use of inquiry-oriented PhET-based activities in conjunction with pre-class reading assignments can improve both the preparation of students for in-class learning and student attitudes towards and engagement with pre-class ass…
▽ More
Pre-class reading assignments help prepare students for active classes by providing a first exposure to the terms and concepts to be used during class. We investigate if the use of inquiry-oriented PhET-based activities in conjunction with pre-class reading assignments can improve both the preparation of students for in-class learning and student attitudes towards and engagement with pre-class assignments. Over three course modules covering different topics, students were assigned randomly to complete either a textbook-only pre-class assignment or both a textbook pre-class assignment and a PhET-based activity. The assignments helped prepare students for class, as measured by performance on the pre-class quiz relative to a beginning-of-semester pre-test, but no evidence for increased learning due the PhET activity was observed. Students rated the assignments which included PhET as more enjoyable and, for the topic latest in the semester, reported engaging more with the assignments when PhET was included.
△ Less
Submitted 15 July, 2016;
originally announced July 2016.
-
Dynamic characterization of crystalline and glass phases of deuterated 1,1,2,2 Tetrachloroethane
Authors:
Silvina Perez,
Mariano Zuriaga,
Pablo Serra,
Alberto Wolfenson,
Philippe Negrier,
Josep Tamarit
Abstract:
A thorough characterization of the γ, β and glass phases of deuterated 1,1,2,2 Tetrachloroethane (C2D2Cl4) via Nuclear Quadrupole Resonance and Molecular Dynamic Simulations (MDS) is reported. The presence of molecular reorientations was experimentally observed in the glass phase and in the β phase. In the β phase, and from MDS, these reorientations are attributed to two possible movements, i.e. a…
▽ More
A thorough characterization of the γ, β and glass phases of deuterated 1,1,2,2 Tetrachloroethane (C2D2Cl4) via Nuclear Quadrupole Resonance and Molecular Dynamic Simulations (MDS) is reported. The presence of molecular reorientations was experimentally observed in the glass phase and in the β phase. In the β phase, and from MDS, these reorientations are attributed to two possible movements, i.e. a $180^o$ reorientation around the C2 molecular symmetry axis and a reorientation of the molecule between non-equivalent positions. In the glass phase, the spin-lattice relaxation time T1 is of the order of 16 times lower that T1 in the crystalline phase and varies as $T^{-1}$ below 100 K in good agreement with the strong quadrupolar relaxation observed in amorphous materials and in the glassy state of molecular organic systems. The activation energy of molecular reorientations in the glass phase (19 kJ/mol) is comparable to that observed in the glassy crystal of a "molecular cousin" compound, Freon 112 (C2F2Cl4), for the secondary β-relaxation. Moreover, the on-site orientational motion of Tetrachloroethane molecules offers a new indirect evidence of the prominent role of such orientational disorder in glassy dynamics.
△ Less
Submitted 15 September, 2015;
originally announced September 2015.
-
Feedback-controlled laser fabrication of micromirror substrates
Authors:
Benjamin Petrak,
Kumarasiri Konthasinghe,
Sonia Perez,
Andreas Muller
Abstract:
Short (40-200 microseconds) single focused CO2 laser pulses of energy of about 100 microJ were used to fabricate high quality concave micromirror templates on silica and fluoride glass. The ablated features have diameters of 20-100 microns and average root-mean-square (RMS) surface microroughness near their center of less than 0.2 nm. Temporally monitoring the fabrication process revealed that it…
▽ More
Short (40-200 microseconds) single focused CO2 laser pulses of energy of about 100 microJ were used to fabricate high quality concave micromirror templates on silica and fluoride glass. The ablated features have diameters of 20-100 microns and average root-mean-square (RMS) surface microroughness near their center of less than 0.2 nm. Temporally monitoring the fabrication process revealed that it proceeds on a time scale shorter than the laser pulse duration. We implement a fast feedback control loop (20 kHz bandwidth) based on the light emitted by the sample that ensures an RMS size dispersion of less than 5 percent in arrays on chips or in individually fabricated features on an optical fiber tip, a significant improvement over previous approaches using longer pulses and open loop operation.
△ Less
Submitted 11 June, 2012;
originally announced June 2012.
