Showing 1–27 of 27 results for author: Paolozzi, L

Testbeam results of irradiated SiGe BiCMOS monolithic silicon pixel detector without internal gain layer

Authors: T. Moretti, M. Milanesio, R. Cardella, T. Kugathasan, A. Picardi, I. Semendyaev, M. Elviretti, H. Rücker, K. Nakamura, Y. Takubo, M. Togawa, F. Cadoux, R. Cardarelli, L. Cecconi, S. Débieux, Y. Favre, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, L. Iodice, R. Kotitsa, C. Magliocca, M. Nessi, A. Pizarro-Medina, J. Sabater Iglesias , et al. (5 additional authors not shown)

Abstract: Samples of the monolithic silicon pixel ASIC prototype produced in 2022 within the framework of the Horizon 2020 MONOLITH ERC Advanced project were irradiated with 70 MeV protons up to a fluence of 1 x 1016 neq/cm2, and then tested using a beam of 120 GeV/c pions. The ASIC contains a matrix of 100 μm pitch hexagonal pixels, readout out by low noise and very fast frontend electronics produced in a… ▽ More Samples of the monolithic silicon pixel ASIC prototype produced in 2022 within the framework of the Horizon 2020 MONOLITH ERC Advanced project were irradiated with 70 MeV protons up to a fluence of 1 x 1016 neq/cm2, and then tested using a beam of 120 GeV/c pions. The ASIC contains a matrix of 100 μm pitch hexagonal pixels, readout out by low noise and very fast frontend electronics produced in a 130 nm SiGe BiCMOS technology process. The dependence on the proton fluence of the efficiency and the time resolution of this prototype was measured with the frontend electronics operated at a power density between 0.13 and 0.9 W/cm2. The testbeam data show that the detection efficiency of 99.96% measured at sensor bias voltage of 200 V before irradiation becomes 96.2% after a fluence of 1 x 1016 neq/cm2. An increase of the sensor bias voltage to 300 V provides an efficiency to 99.7% at that proton fluence. The timing resolution of 20 ps measured before irradiation rises for a proton fluence of 1 x 1016 neq/cm2 to 53 and 45 ps at HV = 200 and 300 V, respectively. △ Less

Submitted 21 June, 2024; v1 submitted 19 April, 2024; originally announced April 2024.

First Measurement of the $ν_e$ and $ν_μ$ Interaction Cross Sections at the LHC with FASER's Emulsion Detector

Authors: FASER Collaboration, Roshan Mammen Abraham, John Anders, Claire Antel, Akitaka Ariga, Tomoko Ariga, Jeremy Atkinson, Florian U. Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Angela Burger, Franck Cadoux, Roberto Cardella, David W. Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Stephane Debieux, Monica D'Onofrio, Ansh Desai, Sergey Dmitrievsky, Sinead Eley, Yannick Favre, Deion Fellers , et al. (80 additional authors not shown)

Abstract: This paper presents the first results of the study of high-energy electron and muon neutrino charged-current interactions in the FASER$ν$ emulsion/tungsten detector of the FASER experiment at the LHC. A subset of the FASER$ν$ volume, which corresponds to a target mass of 128.6~kg, was exposed to neutrinos from the LHC $pp$ collisions with a centre-of-mass energy of 13.6~TeV and an integrated lumin… ▽ More This paper presents the first results of the study of high-energy electron and muon neutrino charged-current interactions in the FASER$ν$ emulsion/tungsten detector of the FASER experiment at the LHC. A subset of the FASER$ν$ volume, which corresponds to a target mass of 128.6~kg, was exposed to neutrinos from the LHC $pp$ collisions with a centre-of-mass energy of 13.6~TeV and an integrated luminosity of 9.5 fb$^{-1}$. Applying stringent selections requiring electrons with reconstructed energy above 200~GeV, four electron neutrino interaction candidate events are observed with an expected background of $0.025^{+0.015}_{-0.010}$, leading to a statistical significance of 5.2$σ$. This is the first direct observation of electron neutrino interactions at a particle collider. Eight muon neutrino interaction candidate events are also detected, with an expected background of $0.22^{+0.09}_{-0.07}$, leading to a statistical significance of 5.7$σ$. The signal events include neutrinos with energies in the TeV range, the highest-energy electron and muon neutrinos ever detected from an artificial source. The energy-independent part of the interaction cross section per nucleon is measured over an energy range of 560--1740 GeV (520--1760 GeV) for $ν_e$ ($ν_μ$) to be $(1.2_{-0.7}^{+0.8}) \times 10^{-38}~\mathrm{cm}^{2}\,\mathrm{GeV}^{-1}$ ($(0.5\pm0.2) \times 10^{-38}~\mathrm{cm}^{2}\,\mathrm{GeV}^{-1}$), consistent with Standard Model predictions. These are the first measurements of neutrino interaction cross sections in those energy ranges. △ Less

Submitted 19 March, 2024; originally announced March 2024.

Time Resolution of a SiGe BiCMOS Monolithic Silicon Pixel Detector without Internal Gain Layer with a Femtosecond Laser

Authors: M. Milanesio, L. Paolozzi, T. Moretti, A. Latshaw, L. Bonacina, R. Cardella, T. Kugathasan, A. Picardi, M. Elviretti, H. Rücker, R. Cardarelli, L. Cecconi, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, L. Iodice, R. Kotitsa, C. Magliocca, M. Nessi, A. Pizarro-Medina, J. Sabater Iglesias, I. Semendyaev, J. Saidi, M. Vicente Barreto Pinto, S. Zambito , et al. (1 additional authors not shown)

Abstract: The time resolution of the second monolithic silicon pixel prototype produced for the MONOLITH H2020 ERC Advanced project was studied using a femtosecond laser. The ASIC contains a matrix of hexagonal pixels with 100 μm pitch, readout by low-noise and very fast SiGe HBT frontend electronics. Silicon wafers with 50 μm thick epilayer with a resistivity of 350 Ωcm were used to produce a fully deplete… ▽ More The time resolution of the second monolithic silicon pixel prototype produced for the MONOLITH H2020 ERC Advanced project was studied using a femtosecond laser. The ASIC contains a matrix of hexagonal pixels with 100 μm pitch, readout by low-noise and very fast SiGe HBT frontend electronics. Silicon wafers with 50 μm thick epilayer with a resistivity of 350 Ωcm were used to produce a fully depleted sensor. At the highest frontend power density tested of 2.7 W/cm2, the time resolution with the femtosecond laser pulses was found to be 45 ps for signals generated by 1200 electrons, and 3 ps in the case of 11k electrons, which corresponds approximately to 0.4 and 3.5 times the most probable value of the charge generated by a minimum-ionizing particle. The results were compared with testbeam data taken with the same prototype to evaluate the time jitter produced by the fluctuations of the charge collection. △ Less

Submitted 11 February, 2024; v1 submitted 2 January, 2024; originally announced January 2024.

Comments: Submitted to JINST

Radiation Tolerance of SiGe BiCMOS Monolithic Silicon Pixel Detectors without Internal Gain Layer

Authors: M. Milanesio, L. Paolozzi, T. Moretti, R. Cardella, T. Kugathasan, F. Martinelli, A. Picardi, I. Semendyaev, S. Zambito, K. Nakamura, Y. Tabuko, M. Togawa, M. Elviretti, H. Rücker, F. Cadoux, R. Cardarelli, S. Débieux, Y. Favre, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, L. Iodice, R. Kotitsa, C. Magliocca, M. Nessi , et al. (5 additional authors not shown)

Abstract: A monolithic silicon pixel prototype produced for the MONOLITH ERC Advanced project was irradiated with 70 MeV protons up to a fluence of 1 x 10^16 1 MeV n_eq/cm^2. The ASIC contains a matrix of hexagonal pixels with 100 μm pitch, readout by low-noise and very fast SiGe HBT frontend electronics. Wafers with 50 μm thick epilayer with a resistivity of 350 Ωcm were used to produce a fully depleted se… ▽ More A monolithic silicon pixel prototype produced for the MONOLITH ERC Advanced project was irradiated with 70 MeV protons up to a fluence of 1 x 10^16 1 MeV n_eq/cm^2. The ASIC contains a matrix of hexagonal pixels with 100 μm pitch, readout by low-noise and very fast SiGe HBT frontend electronics. Wafers with 50 μm thick epilayer with a resistivity of 350 Ωcm were used to produce a fully depleted sensor. Laboratory tests conducted with a 90Sr source show that the detector works satisfactorily after irradiation. The signal-to-noise ratio is not seen to change up to fluence of 6 x 10^14 n_eq /cm^2 . The signal time jitter was estimated as the ratio between the voltage noise and the signal slope at threshold. At -35 {^\circ}C, sensor bias voltage of 200 V and frontend power consumption of 0.9 W/cm^2, the time jitter of the most-probable signal amplitude was estimated to be 21 ps for proton fluence up to 6 x 10 n_eq/cm^2 and 57 ps at 1 x 10^16 n_eq/cm^2 . Increasing the sensor bias to 250 V and the analog voltage of the preamplifier from 1.8 to 2.0 V provides a time jitter of 40 ps at 1 x 10^16 n_eq/cm^2. △ Less

Submitted 30 October, 2023; originally announced October 2023.

Comments: Submitted to JINST

20 ps Time Resolution with a Fully-Efficient Monolithic Silicon Pixel Detector without Internal Gain Layer

Authors: S. Zambito, M. Milanesio, T. Moretti, L. Paolozzi, M. Munker, R. Cardella, T. Kugathasan, F. Martinelli, A. Picardi, M. Elviretti, H. Rücker, A. Trusch, F. Cadoux, R. Cardarelli, S. Débieux, Y. Favre, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, L. Iodice, R. Kotitsa, C. Magliocca, M. Nessi, A. Pizarro-Medina, J. Sabater Iglesias , et al. (3 additional authors not shown)

Abstract: A second monolithic silicon pixel prototype was produced for the MONOLITH project. The ASIC contains a matrix of hexagonal pixels with 100 μm pitch, readout by a low-noise and very fast SiGe HBT frontend electronics. Wafers with 50 μm thick epilayer of 350 Ωcm resistivity were used to produce a fully depleted sensor. Laboratory and testbeam measurements of the analog channels present in the pixel… ▽ More A second monolithic silicon pixel prototype was produced for the MONOLITH project. The ASIC contains a matrix of hexagonal pixels with 100 μm pitch, readout by a low-noise and very fast SiGe HBT frontend electronics. Wafers with 50 μm thick epilayer of 350 Ωcm resistivity were used to produce a fully depleted sensor. Laboratory and testbeam measurements of the analog channels present in the pixel matrix show that the sensor has a 130 V wide bias-voltage operation plateau at which the efficiency is 99.8%. Although this prototype does not include an internal gain layer, the design optimised for timing of the sensor and the front-end electronics provides a time resolutions of 20 ps. △ Less

Submitted 28 January, 2023; originally announced January 2023.

Comments: 11 pages, 11 figures

Testbeam Results of the Picosecond Avalanche Detector Proof-Of-Concept Prototype

Authors: G. Iacobucci, S. Zambito, M. Milanesio, T. Moretti, J. Saidi, L. Paolozzi, M. Munker, R. Cardella, F. Martinelli, A. Picardi, H. Rücker, A. Trusch, P. Valerio, F. Cadoux, R. Cardarelli, S. Débieux, Y. Favre, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, Y. Gurimskaya, R. Kotitsa, C. Magliocca, M. Nessi, A. Pizarro-Medina , et al. (2 additional authors not shown)

Abstract: The proof-of-concept prototype of the Picosecond Avalanche Detector, a multi-PN junction monolithic silicon detector with continuous gain layer deep in the sensor depleted region, was tested with a beam of 180 GeV pions at the CERN SPS. The prototype features low noise and fast SiGe BiCMOS frontend electronics and hexagonal pixels with 100 μm pitch. At a sensor bias voltage of 125 V, the detector… ▽ More The proof-of-concept prototype of the Picosecond Avalanche Detector, a multi-PN junction monolithic silicon detector with continuous gain layer deep in the sensor depleted region, was tested with a beam of 180 GeV pions at the CERN SPS. The prototype features low noise and fast SiGe BiCMOS frontend electronics and hexagonal pixels with 100 μm pitch. At a sensor bias voltage of 125 V, the detector provides full efficiency and average time resolution of 30, 25 and 17 ps in the overall pixel area for a power consumption of 0.4, 0.9 and 2.7 W/cm^2, respectively. In this first prototype the time resolution depends significantly on the distance from the center of the pixel, varying at the highest power consumption measured between 13 ps at the center of the pixel and 25 ps in the inter-pixel region. △ Less

Submitted 23 August, 2022; originally announced August 2022.

The FASER Detector

Authors: FASER Collaboration, Henso Abreu, Elham Amin Mansour, Claire Antel, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David W. Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Olivier Crespo-Lopez, Stephane Debieux, Monica D'Onofrio, Liam Dougherty, Candan Dozen, Abdallah Ezzat, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere , et al. (72 additional authors not shown)

Abstract: FASER, the ForwArd Search ExpeRiment, is an experiment dedicated to searching for light, extremely weakly-interacting particles at CERN's Large Hadron Collider (LHC). Such particles may be produced in the very forward direction of the LHC's high-energy collisions and then decay to visible particles inside the FASER detector, which is placed 480 m downstream of the ATLAS interaction point, aligned… ▽ More FASER, the ForwArd Search ExpeRiment, is an experiment dedicated to searching for light, extremely weakly-interacting particles at CERN's Large Hadron Collider (LHC). Such particles may be produced in the very forward direction of the LHC's high-energy collisions and then decay to visible particles inside the FASER detector, which is placed 480 m downstream of the ATLAS interaction point, aligned with the beam collisions axis. FASER also includes a sub-detector, FASER$ν$, designed to detect neutrinos produced in the LHC collisions and to study their properties. In this paper, each component of the FASER detector is described in detail, as well as the installation of the experiment system and its commissioning using cosmic-rays collected in September 2021 and during the LHC pilot beam test carried out in October 2021. FASER will start taking LHC collision data in 2022, and will run throughout LHC Run 3. △ Less

Submitted 23 July, 2022; originally announced July 2022.

Comments: 92 pages, 72 Figures

Report number: CERN-FASER-2022-001

Journal ref: JINST 19 (2024) P05066

Picosecond Avalanche Detector -- working principle and gain measurement with a proof-of-concept prototype

Authors: L. Paolozzi, M. Munker, R. Cardella, M. Milanesio, Y. Gurimskaya, F. Martinelli, A. Picardi, H. Rücker, A. Trusch, P. Valerio, F. Cadoux, R. Cardarelli, S. Débieux, Y. Favre, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, R. Kotitsa, C. Magliocca, T. Moretti, M. Nessi, A. Pizarro Medina, J. Sabater Iglesias, J. Saidi, M. Vicente Barreto Pinto , et al. (2 additional authors not shown)

Abstract: The Picosecond Avalanche Detector is a multi-junction silicon pixel detector based on a $\mathrm{(NP)_{drift}(NP)_{gain}}$ structure, devised to enable charged-particle tracking with high spatial resolution and picosecond time-stamp capability. It uses a continuous junction deep inside the sensor volume to amplify the primary charge produced by ionizing radiation in a thin absorption layer. The si… ▽ More The Picosecond Avalanche Detector is a multi-junction silicon pixel detector based on a $\mathrm{(NP)_{drift}(NP)_{gain}}$ structure, devised to enable charged-particle tracking with high spatial resolution and picosecond time-stamp capability. It uses a continuous junction deep inside the sensor volume to amplify the primary charge produced by ionizing radiation in a thin absorption layer. The signal is then induced by the secondary charges moving inside a thicker drift region. A proof-of-concept monolithic prototype, consisting of a matrix of hexagonal pixels with 100 $μ$m pitch, has been produced using the 130 nm SiGe BiCMOS process by IHP microelectronics. Measurements on probe station and with a $^{55}$Fe X-ray source show that the prototype is functional and displays avalanche gain up to a maximum electron gain of 23. A study of the avalanche characteristics, corroborated by TCAD simulations, indicates that space-charge effects due to the large primary charge produced by the conversion of X-rays from the $^{55}$Fe source limits the effective gain. △ Less

Submitted 25 September, 2022; v1 submitted 16 June, 2022; originally announced June 2022.

Efficiency and time resolution of monolithic silicon pixel detectors in SiGe BiCMOS technology

Authors: G. Iacobucci, L. Paolozzi, P. Valerio, T. Moretti, F. Cadoux, R. Cardarelli, R. Cardella, S. Débieux, Y. Favre, D. Ferrere, S. Gonzalez-Sevilla, Y. Gurimskaya, R. Kotitsa, C. Magliocca, F. Martinelli, M. Milanesio, M. Münker, M. Nessi, A. Picardi, J. Saidi, H. Rücker, M. Vicente Barreto Pinto, S. Zambito

Abstract: A monolithic silicon pixel detector prototype has been produced in the SiGe BiCMOS SG13G2 130 nm node technology by IHP. The ASIC contains a matrix of hexagonal pixels with pitch of approximately 100 $μ$m. Three analog pixels were calibrated in laboratory with radioactive sources and tested in a 180 GeV/c pion beamline at the CERN SPS. A detection efficiency of $\left(99.9^{+0.1}_{-0.2}\right)$% w… ▽ More A monolithic silicon pixel detector prototype has been produced in the SiGe BiCMOS SG13G2 130 nm node technology by IHP. The ASIC contains a matrix of hexagonal pixels with pitch of approximately 100 $μ$m. Three analog pixels were calibrated in laboratory with radioactive sources and tested in a 180 GeV/c pion beamline at the CERN SPS. A detection efficiency of $\left(99.9^{+0.1}_{-0.2}\right)$% was measured together with a time resolution of $(36.4 \pm 0.8)$ps at the highest preamplifier bias current working point of 150 $μ$A and at a sensor bias voltage of 160 V. The ASIC was also characterized at lower bias voltage and preamplifier current. △ Less

Submitted 21 January, 2022; v1 submitted 16 December, 2021; originally announced December 2021.

The tracking detector of the FASER experiment

Authors: FASER Collaboration, Henso Abreu, Claire Antel, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David W. Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Olivier Crespo-Lopez, Sergey Dmitrievsky, Monica D'Onofrio, Candan Dozen, Abdallah Ezzat, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere, Stephen Gibson, Sergio Gonzalez-Sevilla , et al. (55 additional authors not shown)

Abstract: FASER is a new experiment designed to search for new light weakly-interacting long-lived particles (LLPs) and study high-energy neutrino interactions in the very forward region of the LHC collisions at CERN. The experimental apparatus is situated 480 m downstream of the ATLAS interaction-point aligned with the beam collision axis. The FASER detector includes four identical tracker stations constru… ▽ More FASER is a new experiment designed to search for new light weakly-interacting long-lived particles (LLPs) and study high-energy neutrino interactions in the very forward region of the LHC collisions at CERN. The experimental apparatus is situated 480 m downstream of the ATLAS interaction-point aligned with the beam collision axis. The FASER detector includes four identical tracker stations constructed from silicon microstrip detectors. Three of the tracker stations form a tracking spectrometer, and enable FASER to detect the decay products of LLPs decaying inside the apparatus, whereas the fourth station is used for the neutrino analysis. The spectrometer has been installed in the LHC complex since March 2021, while the fourth station is not yet installed. FASER will start physics data taking when the LHC resumes operation in early 2022. This paper describes the design, construction and testing of the tracking spectrometer, including the associated components such as the mechanics, readout electronics, power supplies and cooling system. △ Less

Submitted 31 May, 2022; v1 submitted 2 December, 2021; originally announced December 2021.

Journal ref: Nucl. Instrum. Methods Phys. Res., A 1034 (2022) 166825

Measurements and analysis of different front-end configurations for monolithic SiGe BiCMOS pixel detectors for HEP applications

Authors: Fulvio Martinelli, Chiara Magliocca, Roberto Cardella, Edoardo Charbon, Giuseppe Iacobucci, Marzio Nessi, Lorenzo Paolozzi, Holger Rücker, Pierpaolo Valerio

Abstract: This paper presents a small-area monolithic pixel detector ASIC designed in 130 nm SiGe BiCMOS technology for the upgrade of the pre-shower detector of the FASER experiment at CERN. The purpose of this prototype is to study the integration of fast front-end electronics inside the sensitive area of the pixels and to identify the configuration that could satisfy at best the specifications of the exp… ▽ More This paper presents a small-area monolithic pixel detector ASIC designed in 130 nm SiGe BiCMOS technology for the upgrade of the pre-shower detector of the FASER experiment at CERN. The purpose of this prototype is to study the integration of fast front-end electronics inside the sensitive area of the pixels and to identify the configuration that could satisfy at best the specifications of the experiment. Self-induced noise, instabilities and cross-talk were minimised to cope with the several challenges associated to the integration of pre-amplifiers and discriminators inside the pixels. The methodology used in the characterisation and the design choices will also be described. Two of the variants studied here will be implemented in the pre-production ASIC of the FASER experiment pre-shower for further tests. △ Less

Submitted 22 November, 2021; originally announced November 2021.

Sub-10 ps Minimum Ionizing Particle Detection with Geiger-Mode APDs

Authors: Francesco Gramuglia, Emanuele Ripiccini, Carlo Alberto Fenoglio, Ming-Lo Wu, Lorenzo Paolozzi, Claudio Bruschini, Edoardo Charbon

Abstract: Major advances in silicon pixel detectors, with outstanding timing performance, have recently attracted significant attention in the community. In this work we present and discuss the use of state-of-the-art Geiger-mode APDs, also known as single-photon avalanche diodes (SPADs), for the detection of minimum ionizing particles (MIPs) with best-in-class timing resolution. The SPADs were implemented… ▽ More Major advances in silicon pixel detectors, with outstanding timing performance, have recently attracted significant attention in the community. In this work we present and discuss the use of state-of-the-art Geiger-mode APDs, also known as single-photon avalanche diodes (SPADs), for the detection of minimum ionizing particles (MIPs) with best-in-class timing resolution. The SPADs were implemented in standard CMOS technology and integrated with on-chip quenching and recharge circuitry. Two devices in coincidence allowed to measure the time-of-flight of 180 GeV/c momentum pions with a coincidence time resolution of 22 ps FWHM (9.5 ps Gaussian sigma). Radiation hardness measurements, also presented here, highlight the suitability of this family of devices for a wide range of high energy physics (HEP) applications. △ Less

Submitted 18 November, 2021; originally announced November 2021.

Report number: 4035033

The trigger and data acquisition system of the FASER experiment

Authors: FASER Collaboration, Henso Abreu, Elham Amin Mansour, Claire Antel, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Stephane Debieux, Sergey Dmitrievsky, Monica D'Onofrio, Candan Dozen, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere, Enrico Gamberini, Edward Karl Galantay , et al. (59 additional authors not shown)

Abstract: The FASER experiment is a new small and inexpensive experiment that is placed 480 meters downstream of the ATLAS experiment at the CERN LHC. FASER is designed to capture decays of new long-lived particles, produced outside of the ATLAS detector acceptance. These rare particles can decay in the FASER detector together with about 500-1000 Hz of other particles originating from the ATLAS interaction… ▽ More The FASER experiment is a new small and inexpensive experiment that is placed 480 meters downstream of the ATLAS experiment at the CERN LHC. FASER is designed to capture decays of new long-lived particles, produced outside of the ATLAS detector acceptance. These rare particles can decay in the FASER detector together with about 500-1000 Hz of other particles originating from the ATLAS interaction point. A very high efficiency trigger and data acquisition system is required to ensure that the physics events of interest will be recorded. This paper describes the trigger and data acquisition system of the FASER experiment and presents performance results of the system acquired during initial commissioning. △ Less

Submitted 10 January, 2022; v1 submitted 28 October, 2021; originally announced October 2021.

Journal ref: 2021_JINST_16_P12028

A massively scalable Time-to-Digital Converter with a PLL-free calibration system in a commercial 130 nm process

Authors: Fulvio Martinelli, Pierpaolo Valerio, Roberto Cardarelli, Edoardo Charbon, Giuseppe Iacobucci, Marzio Nessi, Lorenzo Paolozzi

Abstract: A 33.6 ps LSB Time-to-Digital converter was designed in 130 nm BiCMOS technology. The core of the converter is a differential 9-stage ring oscillator, based on a multi-path architecture. A novel version of this design is proposed, along with an analytical model of linearity. The model allowed us to understand the source of the performance superiority (in terms of linearity) of our design and to pr… ▽ More A 33.6 ps LSB Time-to-Digital converter was designed in 130 nm BiCMOS technology. The core of the converter is a differential 9-stage ring oscillator, based on a multi-path architecture. A novel version of this design is proposed, along with an analytical model of linearity. The model allowed us to understand the source of the performance superiority (in terms of linearity) of our design and to predict further improvements. The oscillator is integrated in a event-by-event self-calibration system that allows avoiding any PLL-based synchronization. For this reason and for the compactness and simplicity of the architecture, the proposed TDC is suitable for applications in which a large number of converters and a massive parallelization are required such as High-Energy Physics and medical imaging detector systems. A test chip for the TDC has been fabricated and tested. The TDC shows a DNL$\leq$1.3 LSB, an INL$\leq$2 LSB and a single-shot precision of 19.5 ps (0.58 LSB). The chip dissipates a power of 5.4 mW overall. △ Less

Submitted 1 September, 2021; v1 submitted 21 July, 2021; originally announced July 2021.

First neutrino interaction candidates at the LHC

Authors: FASER Collaboration, Henso Abreu, Yoav Afik, Claire Antel, Jason Arakawa, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David W. Casper, Charlotte Cavanagh, Francesco Cerutti, Xin Chen, Andrea Coccaro, Monica D'Onofrio, Candan Dozen, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere, Stephen Gibson, Sergio Gonzalez-Sevilla , et al. (51 additional authors not shown)

Abstract: FASER$ν$ at the CERN Large Hadron Collider (LHC) is designed to directly detect collider neutrinos for the first time and study their cross sections at TeV energies, where no such measurements currently exist. In 2018, a pilot detector employing emulsion films was installed in the far-forward region of ATLAS, 480 m from the interaction point, and collected 12.2 fb$^{-1}$ of proton-proton collision… ▽ More FASER$ν$ at the CERN Large Hadron Collider (LHC) is designed to directly detect collider neutrinos for the first time and study their cross sections at TeV energies, where no such measurements currently exist. In 2018, a pilot detector employing emulsion films was installed in the far-forward region of ATLAS, 480 m from the interaction point, and collected 12.2 fb$^{-1}$ of proton-proton collision data at a center-of-mass energy of 13 TeV. We describe the analysis of this pilot run data and the observation of the first neutrino interaction candidates at the LHC. This milestone paves the way for high-energy neutrino measurements at current and future colliders. △ Less

Submitted 26 October, 2021; v1 submitted 13 May, 2021; originally announced May 2021.

Comments: Auxiliary materials are available at https://faser.web.cern.ch/fasernu-first-neutrino-interaction-candidates

Time resolution and power consumption of a monolithic silicon pixel prototype in SiGe BiCMOS technology

Authors: L. Paolozzi, R. Cardarelli, S. Débieux, Y. Favre, D. Ferrère, S. Gonzalez-Sevilla, G. Iacobucci, M. Kaynak, F. Martinelli, M. Nessi, H. Rücker, I. Sanna, DMS Sultan, P. Valerio, E. Zaffaroni

Abstract: SiGe BiCMOS technology can be used to produce ultra-fast, low-power silicon pixel sensors that provide state-of-the-art time resolution even without an internal gain mechanism. The development of such sensors requires the identification of the main factors that may degrade the timing performance and the characterisation of the dependance of the sensor time resolution on the amplifier power consump… ▽ More SiGe BiCMOS technology can be used to produce ultra-fast, low-power silicon pixel sensors that provide state-of-the-art time resolution even without an internal gain mechanism. The development of such sensors requires the identification of the main factors that may degrade the timing performance and the characterisation of the dependance of the sensor time resolution on the amplifier power consumption. Measurements with a $ \mathrm{^{90}Sr} $ source of a prototype sensor produced in SG13G2 technology from IHP Microelectronics, shows a time resolution of 140 ps at an amplifier current of 7 $ \mathrmμ $A and 45 ps at higher power consumption. A full simulation shows that the resolution on the measurement of the signal time-over-threshold, used to correct for time walk, is the main factor affecting the timing performance. △ Less

Submitted 28 August, 2020; v1 submitted 28 May, 2020; originally announced May 2020.

A 50 ps resolution monolithic active pixel sensor without internal gain in SiGe BiCMOS technology

Authors: G. Iacobucci, R. Cardarelli, S. Débieux, F. A. Di Bello, Y. Favre, D. Hayakawa, M. Kaynak, M. Nessi, L. Paolozzi, H. Rücker, DMS Sultan, P. Valerio

Abstract: A monolithic pixelated silicon detector designed for high time resolution has been produced in the SG13G2 130 nm SiGe BiCMOS technology of IHP Mikroelektronik. This proof-of-concept chip contains hexagonal pixels of 65 μm and 130 μm side. The SiGe front-end electronics implemented provides an equivalent noise charge of 90 and 160 electrons for a pixel capacitance of 70 and 220 fF, respectively, an… ▽ More A monolithic pixelated silicon detector designed for high time resolution has been produced in the SG13G2 130 nm SiGe BiCMOS technology of IHP Mikroelektronik. This proof-of-concept chip contains hexagonal pixels of 65 μm and 130 μm side. The SiGe front-end electronics implemented provides an equivalent noise charge of 90 and 160 electrons for a pixel capacitance of 70 and 220 fF, respectively, and a total time walk of less than 1 ns. Lab measurements with a 90Sr source show a time resolution of the order of 50 ps. This result is competitive with silicon technologies that integrate an avalanche gain mechanism. △ Less

Submitted 26 August, 2019; originally announced August 2019.

The TT-PET Data Acquisition and Trigger System

Authors: Y. Bandi, Y. Favre, D. Ferrere, D. Forshaw, R. Hanni, D. Hayakawa, G. Iacobucci, P. Lutz, A. Miucci, L. Paolozzi, E. Ripiccini, C. Tognina, P. Valerio, M. Weber

Abstract: This paper describes the data acquisition and trigger system of the Thin Time-of-flight PET (TT-PET) scanner. The system is designed to read out in the order of 1000 pixel sensors used in the scanner and to provide a reference timing signal to each sensor in order to measure time differences of better than 30 ps. This clock distribution is measured to have a jitter of less than 4 ps at the sensors… ▽ More This paper describes the data acquisition and trigger system of the Thin Time-of-flight PET (TT-PET) scanner. The system is designed to read out in the order of 1000 pixel sensors used in the scanner and to provide a reference timing signal to each sensor in order to measure time differences of better than 30 ps. This clock distribution is measured to have a jitter of less than 4 ps at the sensors. Collected data is locally processed before being forwarded to storage. Data flow as well as control, configuration and monitoring aspects are are also addressed. △ Less

Submitted 10 December, 2018; originally announced December 2018.

Module concept and thermo-mechanical studies of the silicon-based TT-PET small-animal scanner

Authors: Didier Ferrere, Yves Bandi, Frank Cadoux, Dean Forshaw, Daiki Hayakawa, Giuseppe Iacobucci, Sebastien Michal, Antonio Miucci, Marzio Nessi, Lorenzo Paolozzi, Emanuele Ripiccini, Pierpaolo Valerio, Michele Weber

Abstract: The TT-PET collaboration is develo** an MRI-compatible small animal PET scanner in which the sensitive element is a monolithic silicon pixel ASIC targeting 30 ps RMS time resolution. The photon-detection technique is based on a stack of alternating layers of high-Z photon converter and 100 $\mathrm{μm}$ silicon sensors, to produce a scanner with 0.5 $\mathrm{\times}$ 0.5 $\mathrm{\times}$ 0.2… ▽ More The TT-PET collaboration is develo** an MRI-compatible small animal PET scanner in which the sensitive element is a monolithic silicon pixel ASIC targeting 30 ps RMS time resolution. The photon-detection technique is based on a stack of alternating layers of high-Z photon converter and 100 $\mathrm{μm}$ silicon sensors, to produce a scanner with 0.5 $\mathrm{\times}$ 0.5 $\mathrm{\times}$ 0.2 $\mathrm{mm^{3}}$ granularity for precise depth-of-interaction measurement. In this paper we present the results of simulation studies for the expected data rate, time-of-flight and spatial resolution, as well as the performance of image reconstruction with and without the use of timing information. △ Less

Submitted 12 March, 2019; v1 submitted 29 November, 2018; originally announced December 2018.

Comments: arXiv admin note: text overlap with arXiv:1811.12381

Expected performance of the TT-PET scanner

Authors: Emanuele Ripiccini, Daiki Hayakawa, Giuseppe Iacobucci, Marzio Nessi, Elzbieta Nowak, Lorenzo Paolozzi, Osman Ratib, Pierpaolo Valerio, Daniele Vitturini

Abstract: The TT-PET collaboration is develo** a small animal TOF-PET scanner based on silicon detectors featuring 30 ps RMS time resolution and intended to be inserted in an existing MRI scanner. The TT-PET scanner makes use of a stack of layers of high-Z photon-converter and 100 $\mathrm{μm}$ thick silicon sensors, to achieve a scanner with 0.5 $\mathrm{\times}$ 0.5 $\mathrm{\times}$ 0.2… ▽ More The TT-PET collaboration is develo** a small animal TOF-PET scanner based on silicon detectors featuring 30 ps RMS time resolution and intended to be inserted in an existing MRI scanner. The TT-PET scanner makes use of a stack of layers of high-Z photon-converter and 100 $\mathrm{μm}$ thick silicon sensors, to achieve a scanner with 0.5 $\mathrm{\times}$ 0.5 $\mathrm{\times}$ 0.2 $\mathrm{mm^{3}}$ granularity, with precise depth-of-interaction measurement. In this paper we present the results of the Monte Carlo studies for the expected data rate, time resolution on the TOF measurements, spatial resolution and image reconstruction with and without the use of the timing information. Most of the studies have been performed according to the international standards used to assess the performance of small-animal PET system. △ Less

Submitted 29 November, 2018; originally announced November 2018.

Characterization of the demonstrator of the fast silicon monolithic ASIC for the TT-PET project

Authors: Lorenzo Paolozzi, Yves Bandi, Roberto Cardarelli, Stephane Debieux, Yannick Favre, Didier Ferrere, Dean Forshaw, Daiki Hayakawa, Giuseppe Iacobucci, Mehmet Kaynak, Antonio Miucci, Marzio Nessi, Emanuele Ripiccini, Holger Ruecker, Pierpaolo Valerio, Michele Weber

Abstract: The TT-PET collaboration is develo** a small animal TOF-PET scanner based on monolithic silicon pixel sensors in SiGe BiCMOS technology. The demonstrator chip, a small-scale version of the final detector ASIC, consists of a 3 x 10 pixel matrix integrated with the front-end, a 50 ps binning TDC and read out logic. The chip, thinned down to 100 μm and backside metallized, was operated at a voltage… ▽ More The TT-PET collaboration is develo** a small animal TOF-PET scanner based on monolithic silicon pixel sensors in SiGe BiCMOS technology. The demonstrator chip, a small-scale version of the final detector ASIC, consists of a 3 x 10 pixel matrix integrated with the front-end, a 50 ps binning TDC and read out logic. The chip, thinned down to 100 μm and backside metallized, was operated at a voltage of 180 V. The tests on a beam line of minimum ionizing particles show a detection efficiency greater than 99.9 % and a time resolution down to 110 ps. △ Less

Submitted 27 November, 2018; originally announced November 2018.

A monolithic ASIC demonstrator for the Thin Time-of-Flight PET scanner

Authors: Pierpaolo Valerio, Roberto Cardarelli, Giuseppe Iacobucci, Lorenzo Paolozzi, Emanuele Ripiccini, Daiki Hayakawa, Salvatore Bruno, Alessandro Caltabiano, Mehmet Kaynak, Holger Rueker, Marzio Nessi

Abstract: Time-of-flight measurement is an important advancement in PET scanners to improve image reconstruction with a lower delivered radiation dose. This article describes the monolithic ASIC for the TT-PET project, a novel idea for a high-precision PET scanner for small animals. The chip uses a SiGe Bi-CMOS process for timing measurements, integrating a fully-depleted pixel matrix with a low-power BJT-b… ▽ More Time-of-flight measurement is an important advancement in PET scanners to improve image reconstruction with a lower delivered radiation dose. This article describes the monolithic ASIC for the TT-PET project, a novel idea for a high-precision PET scanner for small animals. The chip uses a SiGe Bi-CMOS process for timing measurements, integrating a fully-depleted pixel matrix with a low-power BJT-based front-end per channel, integrated on the same 100 $μ m$ thick die. The target timing resolution is 30 ps RMS for electrons from the conversion of 511 keV photons. A novel synchronization scheme using a patent-pending TDC is used to allow the synchronization of 1.6 million channels across almost 2000 different chips at picosecond-level. A full-featured demonstrator chip with a 3x10 matrix of 500x500 $μ m^{2}$ pixels was produced to validate each block. Its design and experimental results are presented here. △ Less

Submitted 26 November, 2018; originally announced November 2018.

Design a TDC in SiGe for RPC's electronics Front-end for the use in a high-rate experiment

Authors: Salvatore Bruno, Roberto Cardarelli, Giulio Aielli, davide Badoni, Paolo Camarri, Anna Di Ciaccio, Eelio Alunno Camelia, Alessandro Caltabiano, Lorenzo Massa, Lorenzo Paolozzi, Luca Pizzimento, Alessandro Rocchi

Abstract: With the new generation of the RPC, it is possible to work with induced signals of hundreds $μV$, hence the front-end electronics is an important and delicate part of the detector in order to get a detectable signal. The electronic chain is made up of an amplifier, a discriminator, a TDC. The new front-end is realized with the use of silicon-germanium (SiGe) components, provided by IHP microelectr… ▽ More With the new generation of the RPC, it is possible to work with induced signals of hundreds $μV$, hence the front-end electronics is an important and delicate part of the detector in order to get a detectable signal. The electronic chain is made up of an amplifier, a discriminator, a TDC. The new front-end is realized with the use of silicon-germanium (SiGe) components, provided by IHP microelectronics. With this technology we can implement BJT and CMOS transistors on the same chip. The benefit of this improvement is to minimize: power consumption of the channels ($2 ÷3$ $ \frac{mW}{ch}$), noise (500 $e^-$ r.m.s), radiation hardness (10 kGy,$10^3$ $\frac{n}{cm}$) and it maximizes the speed of response electronics. In this work I will highlight the first TDC prototypes' results. The TDC uses a local oscillator, that has an oscillation range between $0.6 ÷3 $ GHz, and a the temporal jitter of 15 ps. The data output from the TDC are presented in binary in order to lighten data processing to the acquisition system. Moreover, we are studying a way to minimize system latency. This optimization involves the addition of a serializer (PISO) that sends the TDC data output to the acquisition system at 2 GHz. △ Less

Submitted 21 June, 2018; v1 submitted 11 June, 2018; originally announced June 2018.

Comments: 7 pages, 11 figures, RPC conference 2018, JINST 2018

Test beam measurement of the first prototype of the fast silicon pixel monolithic detector for the TT-PET project

Authors: L. Paolozzi, Y. Bandi, M. Benoit, R. Cardarelli, S. Débieux, D. Forshaw, D. Hayakawa, G. Iacobucci, M. Kaynak, A. Miucci, M. Nessi, O. Ratib, E. Ripiccini, H. Rücker, P. Valerio, M. Weber

Abstract: The TT-PET collaboration is develo** a PET scanner for small animals with 30 ps time-of-flight resolution and sub-millimetre 3D detection granularity. The sensitive element of the scanner is a monolithic silicon pixel detector based on state-of-the-art SiGe BiCMOS technology. The first ASIC prototype for the TT-PET was produced and tested in the laboratory and with minimum ionizing particles. Th… ▽ More The TT-PET collaboration is develo** a PET scanner for small animals with 30 ps time-of-flight resolution and sub-millimetre 3D detection granularity. The sensitive element of the scanner is a monolithic silicon pixel detector based on state-of-the-art SiGe BiCMOS technology. The first ASIC prototype for the TT-PET was produced and tested in the laboratory and with minimum ionizing particles. The electronics exhibit an equivalent noise charge below 600 e- RMS and a pulse rise time of less than 2 ns, in accordance with the simulations. The pixels with a capacitance of 0.8 pF were measured to have a detection efficiency greater than 99% and, although in the absence of the post-processing, a time resolution of approximately 200 ps. △ Less

Submitted 6 February, 2018; v1 submitted 5 February, 2018; originally announced February 2018.

Improving the RPC rate capability

Authors: G. Aielli, P. Camarri, R. Cardarelli, A. Di Ciaccio, L. Di Stante, R. Iuppa, B. Liberti, L. Paolozzi, E. Pastori, R. Santonico, M. Toppi

Abstract: This paper has the purpose to study the rate capability of the Resistive Plate Chamber, RPC, starting from the basic physics of this detector. The effect of different working parameters determining the rate capability is analysed in detail, in order to optimize a new family of RPCs for applications to heavy irradiation environments and in particular to the LHC phase 2. A special emphasis is given… ▽ More This paper has the purpose to study the rate capability of the Resistive Plate Chamber, RPC, starting from the basic physics of this detector. The effect of different working parameters determining the rate capability is analysed in detail, in order to optimize a new family of RPCs for applications to heavy irradiation environments and in particular to the LHC phase 2. A special emphasis is given to the improvement achievable by minimizing the avalanche charge delivered in the gas. The paper shows experimental results of Cosmic Ray tests, performed to study the avalanche features for different gas gap sizes, with particular attention to the overall delivered charge. For this purpose, the paper studies, in parallel to the prompt electronic signal, also the ionic signal which gives the main contribution to the delivered charge. Whenever possible the test results are interpreted on the base of the RPC detector physics and are intended to extend and reinforce our physical understanding of this detector. △ Less

Submitted 10 June, 2016; originally announced June 2016.

Comments: Submitted to JINST Journal of Instrumentation for pubblication

100ps time resolution with thin silicon pixel detectors and a SiGe HBT amplifier

Authors: Mathieu Benoit, Roberto Cardarelli, Stéphane Débieux, Yannick Favre, Giuseppe Iacobucci, Marzio Nessi, Lorenzo Paolozzi, Kenji Shu

Abstract: A 100um thick silicon detector with 1mm2 pad readout optimized for sub-nanosecond time resolution has been developed and tested. Coupled to a purposely developed amplifier based on SiGe HBT technology, this detector was characterized at the H8 beam line at the CERN SPS. An excellent time resolution of (106+-1)ps for silicon detectors was measured with minimum ionizing particles. A 100um thick silicon detector with 1mm2 pad readout optimized for sub-nanosecond time resolution has been developed and tested. Coupled to a purposely developed amplifier based on SiGe HBT technology, this detector was characterized at the H8 beam line at the CERN SPS. An excellent time resolution of (106+-1)ps for silicon detectors was measured with minimum ionizing particles. △ Less

Submitted 13 November, 2015; originally announced November 2015.

Studies on fast triggering and high precision tracking with Resistive Plate Chambers

Authors: G. Aielli, B. Bilki, R. Ball, J. W. Chapman, R. Cardarelli, T. Dai, E. Diehl, J. Dubbert, C. Ferretti, H. Feng, K. Francis, L. Guan, L. Han, S. Hou, D. Levin, B. Li, L. Liu, L. Paolozzi, J. Repond, J. Roloff, R. Santonico, H. Y. Song, X. L. Wang, Y. Wu, L. Xia , et al. (5 additional authors not shown)

Abstract: We report on studies of fast triggering and high-precision tracking using Resistive Plate Chambers (RPCs). Two beam tests were carried out with the 180 GeV muon beam at CERN using RPCs with gas gaps of 1.00 or 1.15 mm and equipped with readout strips with 1.27 mm pitch. This is the first beam test of RPCs with fine-pitch readout strips that explores simultaneously precision tracking and triggering… ▽ More We report on studies of fast triggering and high-precision tracking using Resistive Plate Chambers (RPCs). Two beam tests were carried out with the 180 GeV muon beam at CERN using RPCs with gas gaps of 1.00 or 1.15 mm and equipped with readout strips with 1.27 mm pitch. This is the first beam test of RPCs with fine-pitch readout strips that explores simultaneously precision tracking and triggering capabilities. RPC signals were acquired with precision timing and charge integrating readout electronics at both ends of the strips. The time resolution was measured to be better than 600 ps and the average spatial resolution was found to be 220 um using charge information and 287 um using timing information. The dual-ended readout allows the determination of the average and the difference of the signal arrival times. The average time was found to be independent of the incident particle position along the strip and is useful for triggering purposes. The time difference yielded a determination of the hit position with a precision of 7.5 mm along the strip. These results demonstrate the feasibility using RPCs for fast and high-resolution triggering and tracking. △ Less

Submitted 24 October, 2012; originally announced October 2012.

Comments: 7 pages, 11 figures, submitted to Nucl. Instru. Meth