-
Graphene-Based Transparent Flexible Strain Gauges with Tunable Sensitivity and Strain Range
Authors:
Joseph Neilson,
Pietro Cataldi,
Brian Derby
Abstract:
Flexible strain gauges with 88% optical transmittance, of reduced graphene oxide (rGO) on poly dimethylsiloxne membranes, are produced form monolayers of graphene oxide assembled into densely packed sheets at an immiscible hexane/water interface and subsequently reduced in HI vapor to increase electrical conductivity. Pre-straining and relaxing the membranes introduces a population of cracks into…
▽ More
Flexible strain gauges with 88% optical transmittance, of reduced graphene oxide (rGO) on poly dimethylsiloxne membranes, are produced form monolayers of graphene oxide assembled into densely packed sheets at an immiscible hexane/water interface and subsequently reduced in HI vapor to increase electrical conductivity. Pre-straining and relaxing the membranes introduces a population of cracks into the rGO film. Subsequent straining opens these cracks, inducing piezoresistivity. Reduction for 30 s forms an array of parallel cracks that do not individually span the membrane and results in a strain gauge with a usable strain range > 0.2 and gauge factor of 20 - 100 at low strain levels that increases with increasing pre-strain. In all cases the gauge facto decreases with increasing applied strain and asymptotes to a value of about 3, as it approaches the pre-strain value. If the rGO is reduced for 60 s, the cracks fully span the width of the membrane, leading to an increased gauge resistance but a much more sensitive strain gauge with GF ranging from 1000 - 16000. However, the usable strain range reduces to < 0.01. A simple equivalent resistor model is proposed to describe the behaviour of both gauge types. The gauges show a repeatable and stable response with loading frequencies up to 1 kHz and have been used to detect human body motion in a simple e-skin demonstration.
△ Less
Submitted 9 June, 2023; v1 submitted 27 April, 2023;
originally announced April 2023.
-
Ternary Quarter Wavelength Coatings for Gravitational Wave Detector Mirrors: Design Optimization via Exhaustive Search
Authors:
V. Pierro,
V. Fiumara,
F. Chiadini,
V. Granata,
C. Di Giorgio,
O. Durante,
J. Neilson,
R. Fittipaldi,
G. Carapella,
F. Bobba,
M. Principe,
I. M. Pinto
Abstract:
Multimaterial optical coatings are a promising viable option to meet the challenging requirements (in terms of transmittance, absorbance and thermal noise) of next generation gravitational wave detector mirrors. In this paper we focus on ternary coatings consisting of quarter-wavelength thick layers, where a third material (H') is added to the two presently in use, namely Silica (L) and Titania-do…
▽ More
Multimaterial optical coatings are a promising viable option to meet the challenging requirements (in terms of transmittance, absorbance and thermal noise) of next generation gravitational wave detector mirrors. In this paper we focus on ternary coatings consisting of quarter-wavelength thick layers, where a third material (H') is added to the two presently in use, namely Silica (L) and Titania-doped Tantala (H), featuring higher dielectric contrast (against Silica), and lower thermal noise (compared to Titania-doped Tantala), but higher optical losses. We seek the optimal material sequences, featuring minimal thermal (Brownian) noise under prescribed transmittance and absorbance constraints, by exhaustive simulation over all possible configurations, for different values (in a meaningful range) of the optical density and extinction coefficient of the third material. In all cases studied, the optimal designs consist of a stack of (H'|L) doublets topped by a stack of (H|L) doublets, confirming previous heuristic assumptions, and the achievable coating noise power spectral density reduction factor is \sim 0.5. The robustness of the found optimal designs against layer thickness deposition errors and uncertainties and/or fluctuations in the optical losses of the third material is also investigated. Possible margins for further thermal noise reduction by layer thickness optimization, and strategies to implement it, are discussed.
△ Less
Submitted 8 May, 2021; v1 submitted 3 December, 2020;
originally announced December 2020.
-
On the performance limits of coatings for gravitational wave detectors made of alternating layers of two materials
Authors:
V. Pierro,
V. Fiumara,
F. Chiadini,
F. Bobba,
G. Carapella,
C. Di Giorgio,
O. Durante,
R. Fittipaldi,
E. Mejuto Villa,
J. Neilson,
M. Principe,
I. M. Pinto
Abstract:
The coating design for mirrors used in interferometric detectors of gravitational waves currently consists of stacks of two alternating dielectric materials with different refractive indexes. In order to explore the performance limits of such coatings, we have formulated and solved the design problem as a multiobjective optimization problem consisting of the minimization of both coating transmitta…
▽ More
The coating design for mirrors used in interferometric detectors of gravitational waves currently consists of stacks of two alternating dielectric materials with different refractive indexes. In order to explore the performance limits of such coatings, we have formulated and solved the design problem as a multiobjective optimization problem consisting of the minimization of both coating transmittance and thermal noise. An algorithm of global optimization (Borg MOEA) has been used without any a priori assumption on the number and thicknesses of the layers in the coating. The algorithm yields to a Pareto tradeoff boundary exhibiting a continuous, decreasing and non convex (bump-like) profile, bounded from below by an exponential curve which can be written in explicit closed form in the transmittance-noise plane. The lower bound curve has the same expression of the relation between transmittance and noise for the quarter wavelength design where the noise coefficient of the high refractive index material assumes a smaller equivalent value. An application of this result allowing to reduce the computational burden of the search procedure is reported and discussed.
△ Less
Submitted 29 July, 2019; v1 submitted 16 April, 2019;
originally announced April 2019.
-
The Compact Linear Collider (CLIC) - 2018 Summary Report
Authors:
The CLIC,
CLICdp collaborations,
:,
T. K. Charles,
P. J. Giansiracusa,
T. G. Lucas,
R. P. Rassool,
M. Volpi,
C. Balazs,
K. Afanaciev,
V. Makarenko,
A. Patapenka,
I. Zhuk,
C. Collette,
M. J. Boland,
A. C. Abusleme Hoffman,
M. A. Diaz,
F. Garay,
Y. Chi,
X. He,
G. Pei,
S. Pei,
G. Shu,
X. Wang,
J. Zhang
, et al. (671 additional authors not shown)
Abstract:
The Compact Linear Collider (CLIC) is a TeV-scale high-luminosity linear $e^+e^-$ collider under development at CERN. Following the CLIC conceptual design published in 2012, this report provides an overview of the CLIC project, its current status, and future developments. It presents the CLIC physics potential and reports on design, technology, and implementation aspects of the accelerator and the…
▽ More
The Compact Linear Collider (CLIC) is a TeV-scale high-luminosity linear $e^+e^-$ collider under development at CERN. Following the CLIC conceptual design published in 2012, this report provides an overview of the CLIC project, its current status, and future developments. It presents the CLIC physics potential and reports on design, technology, and implementation aspects of the accelerator and the detector. CLIC is foreseen to be built and operated in stages, at centre-of-mass energies of 380 GeV, 1.5 TeV and 3 TeV, respectively. CLIC uses a two-beam acceleration scheme, in which 12 GHz accelerating structures are powered via a high-current drive beam. For the first stage, an alternative with X-band klystron powering is also considered. CLIC accelerator optimisation, technical developments and system tests have resulted in an increased energy efficiency (power around 170 MW) for the 380 GeV stage, together with a reduced cost estimate at the level of 6 billion CHF. The detector concept has been refined using improved software tools. Significant progress has been made on detector technology developments for the tracking and calorimetry systems. A wide range of CLIC physics studies has been conducted, both through full detector simulations and parametric studies, together providing a broad overview of the CLIC physics potential. Each of the three energy stages adds cornerstones of the full CLIC physics programme, such as Higgs width and couplings, top-quark properties, Higgs self-coupling, direct searches, and many precision electroweak measurements. The interpretation of the combined results gives crucial and accurate insight into new physics, largely complementary to LHC and HL-LHC. The construction of the first CLIC energy stage could start by 2026. First beams would be available by 2035, marking the beginning of a broad CLIC physics programme spanning 25-30 years.
△ Less
Submitted 6 May, 2019; v1 submitted 14 December, 2018;
originally announced December 2018.
-
A Multi-Moded RF Delay Line Distribution System for the Next Linear Collider
Authors:
S. G. Tantawi,
C. Nantista,
N. Kroll,
Z. Li,
R. Miller,
R. Ruth,
P. Wilson,
J. Neilson
Abstract:
The Delay Line Distribution System (DLDS) is an alternative to conventional pulse compression, which enhances the peak power of rf sources while matching the long pulse of those sources to the shorter filling time of accelerator structures. We present an implementation of this scheme that combines pairs of parallel delay lines of the system into single lines. The power of several sources is comb…
▽ More
The Delay Line Distribution System (DLDS) is an alternative to conventional pulse compression, which enhances the peak power of rf sources while matching the long pulse of those sources to the shorter filling time of accelerator structures. We present an implementation of this scheme that combines pairs of parallel delay lines of the system into single lines. The power of several sources is combined into a single waveguide delay line using a multi-mode launcher. The output mode of the launcher is determined by the phase coding of the input signals. The combined power is extracted from the delay line using mode-selective extractors, each of which extracts a single mode. Hence, the phase coding of the sources controls the output port of the combined power. The power is then fed to the local accelerator structures. We present a detailed design of such a system, including several implementation methods for the launchers, extractors, and ancillary high power rf components. The system is designed so that it can handle the 600 MW peak power required by the NLC design while maintaining high efficiency.
△ Less
Submitted 17 September, 2002;
originally announced September 2002.
