-
Fine residual stress distribution measurement of steel materials by SOI pixel detector with synchrotron X-rays
Authors:
Ryutaro Nishimura,
Shunji Kishimoto,
Toshihiko Sasaki,
Shingo Mitsui,
Masayoshi Shinya,
Yasuo Arai,
Toshinobu Miyoshi
Abstract:
Residual stress is an important factor governing evaluating and controlling the quality of metal materials in industrial products. X-ray measurements provide one of the most effective means of evaluating residual stress without destruction. In such measurements, the effects of residual stress on the crystal structure can be observed through the Debye ring deformation.
In previous studies, we dev…
▽ More
Residual stress is an important factor governing evaluating and controlling the quality of metal materials in industrial products. X-ray measurements provide one of the most effective means of evaluating residual stress without destruction. In such measurements, the effects of residual stress on the crystal structure can be observed through the Debye ring deformation.
In previous studies, we developed a residual stress measurement system based on the $cos α$ method, using a two-dimensional (2D) silicon-on-insulator pixel (SOIPIX) detector known as INTPIX4. In a typical laboratory setup, this system requires only 1 second to measure a specified point. This is drastically faster than the conventional system based on the $sin^{2} ψ$ method, which requires more than 10 min, and the $cos α$-based system using an imaging plate, which requires 1 min. Compared to other systems, it can evaluate the 2D distribution of residual stress faster and provide more detailed information for evaluating materials. We first attempted to measure the 2D distribution in a laboratory setup with a Cr X-ray tube (Cr K$α$ 5.4 keV) and obtained satisfactory results. We subsequently took measurements using synchrotron monochromatic X-rays to determine the fine accuracy and fine sampling pitch distribution. In this paper, we report the results of the initial synchrotron experiment, including the residual stress distribution of the standard specimen obtained by the first prototype setup. Furthermore, we compare the synchrotron measurements with those from the laboratory.
△ Less
Submitted 14 May, 2024;
originally announced May 2024.
-
On methods for assessment of the influence and impact of observations in convection-permitting numerical weather prediction
Authors:
Guannan Hu,
Sarah L. Dance,
Alison Fowler,
David Simonin,
Joanne Waller,
Thomas Auligne,
Sean Healy,
Daisuke Hotta,
Ulrich Löhnert,
Takemasa Miyoshi,
Nikki C. Prive,
Olaf Stiller,
Xuguang Wang,
Martin Weissmann
Abstract:
In numerical weather prediction (NWP), a large number of observations are used to create initial conditions for weather forecasting through a process known as data assimilation. An assessment of the value of these observations for NWP can guide us in the design of future observation networks, help us to identify problems with the assimilation system, and allow us to assess changes to the assimilat…
▽ More
In numerical weather prediction (NWP), a large number of observations are used to create initial conditions for weather forecasting through a process known as data assimilation. An assessment of the value of these observations for NWP can guide us in the design of future observation networks, help us to identify problems with the assimilation system, and allow us to assess changes to the assimilation system. However, the assessment can be challenging in convection-permitting NWP. First, the strong nonlinearity in the forecast model limits the methods available for the assessment. Second, convection-permitting NWP typically uses a limited area model and provides short forecasts, giving problems with verification and our ability to gather sufficient statistics. Third, convection-permitting NWP often makes use of novel observations, which can be difficult to simulate in an observing system simulation experiment (OSSE). We compare methods that can be used to assess the value of observations in convection-permitting NWP and discuss operational considerations when using these methods. We focus on their applicability to ensemble forecasting systems, as these systems are becoming increasingly dominant for convection-permitting NWP. We also identify several future research directions: comparison of forecast validation using analyses and observations, the effect of ensemble size on assessing the value of observations, flow-dependent covariance localization, and generation and validation of the nature run in an OSSE.
△ Less
Submitted 28 September, 2023;
originally announced September 2023.
-
Proton radiation damage tolerance of wide dynamic range SOI pixel detectors
Authors:
Shun Tsunomachi,
Takayoshi Kohmura,
Kouichi Hagino,
Masatoshi Kitajima,
Toshiki Doi,
Daiki Aoki,
Asuka Ohira,
Yasuyuki Shimizu,
Kaito Fujisawa,
Shizusa Yamazaki,
Yuusuke Uchida,
Makoto Shimizu,
Naoki Itoh,
Yasuo Arai,
Toshinobu Miyoshi,
Ryutaro Nishimura,
Takeshi Go Tsuru,
Ikuo Kurachi
Abstract:
We have been develo** the SOI pixel detector ``INTPIX'' for space use and general purpose applications such as the residual stress measurement of a rail and high energy physics experiments. INTPIX is a monolithic pixel detector composed of a high-resistivity Si sensor, a SiO2 insulator, and CMOS pixel circuits utilizing Silicon-On-Insulator (SOI) technology. We have considered the possibility of…
▽ More
We have been develo** the SOI pixel detector ``INTPIX'' for space use and general purpose applications such as the residual stress measurement of a rail and high energy physics experiments. INTPIX is a monolithic pixel detector composed of a high-resistivity Si sensor, a SiO2 insulator, and CMOS pixel circuits utilizing Silicon-On-Insulator (SOI) technology. We have considered the possibility of using INTPIX to observe X-ray polarization in space. When the semiconductor detector is used in space, it is subject to radiation damage resulting from high-energy protons. Therefore, it is necessary to investigate whether INTPIX has high radiation tolerance for use in space. The INTPIX8 was irradiated with 6 MeV protons up to a total dose of 2 krad at HIMAC, National Institute of Quantum Science in Japan, and evaluated the degradation of the performance, such as energy resolution and non-uniformity of gain and readout noise between pixels. After 500 rad irradiation, which is the typical lifetime of an X-ray astronomy satellite, the degradation of energy resolution at 14.4 keV is less than 10%, and the non-uniformity of readout noise and gain between pixels is constant within 0.1%.
△ Less
Submitted 8 September, 2022;
originally announced September 2022.
-
Development of a new high-speed data acquisition system prototype for SOI pixel detector using SiTCP-XG, a 10-gigabit Ethernet network processor
Authors:
Ryutaro Nishimura,
Shunji Kishimoto,
Yasuo Arai,
Toshinobu Miyoshi
Abstract:
We are develo** a new readout board with a newer generation field-programmable gate array (FPGA) and the 10-gigabit ethernet to improve the performance and usability of the current readout board based on the 1-gigabit Ethernet. In this new readout board, the SiTCP-XG network processor supporting 10-gigabit Ethernet was implemented. SiTCP is a network processor circuit running on FPGA, and SiTCP-…
▽ More
We are develo** a new readout board with a newer generation field-programmable gate array (FPGA) and the 10-gigabit ethernet to improve the performance and usability of the current readout board based on the 1-gigabit Ethernet. In this new readout board, the SiTCP-XG network processor supporting 10-gigabit Ethernet was implemented. SiTCP is a network processor circuit running on FPGA, and SiTCP-XG is the newly developed version of the SiTCP that supports 10-gigabit Ethernet. Before develo** the new board, we constructed a prototype system using the Xilinx FPGA evaluation board KC705 to evaluate the SiTCP-XG. This prototype system was tested with the SOI pixel detector, which has 425,984 (column 832 x row 512 matrix) pixels and a pixel size of 17 x 17 um at the synchrotron beamlines of the PhotonFactory (KEK). This was the first test of the X-ray imaging for this system. The results showed that this system worked stably with a transfer rate of 682 Mbps (equivalent to a frame rate of 100 fps, limited by detector operation parameters), and also worked stably with a transfer rate of 2.4 Gbps (equivalent to 350 fps, the maximum rate limited by the detector performance). These results suggest that the SiTCP-XG system has sufficient transfer performance to cover the SOIPIX detector performance.
△ Less
Submitted 9 July, 2022;
originally announced July 2022.
-
A low-dissipation HLLD approximate Riemann solver for a very wide range of Mach numbers
Authors:
Takashi Minoshima,
Takahiro Miyoshi
Abstract:
We propose a new Harten-Lax-van Leer discontinuities (HLLD) approximate Riemann solver to improve the stability of shocks and the accuracy of low-speed flows in multidimensional magnetohydrodynamic (MHD) simulations. Stringent benchmark tests verify that the new solver is more robust against a numerical shock instability and is more accurate for low-speed, nearly incompressible flows than the orig…
▽ More
We propose a new Harten-Lax-van Leer discontinuities (HLLD) approximate Riemann solver to improve the stability of shocks and the accuracy of low-speed flows in multidimensional magnetohydrodynamic (MHD) simulations. Stringent benchmark tests verify that the new solver is more robust against a numerical shock instability and is more accurate for low-speed, nearly incompressible flows than the original solver, whereas additional computational costs are quite low. The novel ability of the new solver enables us to tackle MHD systems, including both high and low Mach number flows.
△ Less
Submitted 10 August, 2021;
originally announced August 2021.
-
INTPIX4NA -- new integration-type silicon-on-insulator pixel detector for imaging application
Authors:
R. Nishimura,
S. Kishimoto,
T. Sasaki,
S. Mitsui,
M. Shinya,
Y. Arai,
T. Miyoshi
Abstract:
INTPIX4NA is an integration-type silicon-on-insulator pixel detector. This detector has a 14.1 x 8.7 mm^2 sensitive area, 425,984 (832 column x 512 row matrix) pixels and the pixel size is 17 x 17 um^2. This detector was developed for residual stress measurement using X-rays (the cos alpha method). The performance of INTPIX4NA was tested with the synchrotron beamlines of the Photon Factory (KEK),…
▽ More
INTPIX4NA is an integration-type silicon-on-insulator pixel detector. This detector has a 14.1 x 8.7 mm^2 sensitive area, 425,984 (832 column x 512 row matrix) pixels and the pixel size is 17 x 17 um^2. This detector was developed for residual stress measurement using X-rays (the cos alpha method). The performance of INTPIX4NA was tested with the synchrotron beamlines of the Photon Factory (KEK), and the following results were obtained. The modulation transfer function, the index of the spatial resolution, was more than 50% at the Nyquist frequency (29.4 cycle/mm). The energy resolution analyzed from the collected charge counts is 35.3%--46.2% at 5.415 keV, 21.7%--35.6% at 8 keV, and 15.7%--19.4% at 12 keV. The X-ray signal can be separated from the noise even at a low energy of 5.415 keV at room temperature (approximately 25--27 degree Celsius). The maximum frame rate at which the signal quality can be maintained is 153 fps in the current measurement system. These results satisfy the required performance in the air and at room temperature (approximately 25--27 degree Celsius) condition that is assumed for the environment of the residual stress measurement.
△ Less
Submitted 14 January, 2022; v1 submitted 27 July, 2021;
originally announced July 2021.
-
A short note on reconstruction variables in shock capturing schemes for magnetohydrodynamics
Authors:
Takahiro Miyoshi,
Takashi Minoshima
Abstract:
We propose a set of quick and easy approximate characteristic variables for higher-order reconstructions of shock capturing schemes for magnetohydrodynamics (MHD). Numerical experiments suggest that the reconstructions using the approximate characteristic variables are more robust than those using the conservative or primitive variables, while their computational efficiencies are comparable. The a…
▽ More
We propose a set of quick and easy approximate characteristic variables for higher-order reconstructions of shock capturing schemes for magnetohydrodynamics (MHD). Numerical experiments suggest that the reconstructions using the approximate characteristic variables are more robust than those using the conservative or primitive variables, while their computational efficiencies are comparable. The approximate characteristic variables are simple compared to the full characteristic variables for MHD, and can be a practical choice of reconstruction variables.
△ Less
Submitted 1 September, 2020;
originally announced September 2020.
-
Development of a Neutron Imaging Sensor using INTPIX4-SOI Pixelated Silicon Devices
Authors:
Y. Kamiya,
T. Miyoshi,
H. Iwase,
T. Inada,
A. Mizushima,
Y. Mita,
K. Shimazoe,
H. Tanaka,
I. Kurachi,
Y. Arai
Abstract:
We have developed a neutron imaging sensor based on an INTPIX4-SOI pixelated silicon device. Neutron irradiation tests are performed at several neutron facilities to investigate sensor's responses for neutrons. Detection efficiency is measured to be around $1.5$\% for thermal neutrons. Upper bound of spatial resolution is evaluated to be $4.1 \pm 0.2 ~μ$m in terms of a standard deviation of the li…
▽ More
We have developed a neutron imaging sensor based on an INTPIX4-SOI pixelated silicon device. Neutron irradiation tests are performed at several neutron facilities to investigate sensor's responses for neutrons. Detection efficiency is measured to be around $1.5$\% for thermal neutrons. Upper bound of spatial resolution is evaluated to be $4.1 \pm 0.2 ~μ$m in terms of a standard deviation of the line spread function.
△ Less
Submitted 10 June, 2020;
originally announced June 2020.
-
Plasmoid-dominated Turbulent Reconnection in a Low $β$ Plasma
Authors:
Seiji Zenitani,
Takahiro Miyoshi
Abstract:
Properties of plasmoid-dominated turbulent reconnection in a low-$β$ background plasma are investigated by resistive magnetohydrodynamic (MHD) simulations. In the $β_{\rm in} < 1$ regime, where $β_{\rm in}$ is plasma $β$ in the inflow region, the reconnection site is dominated by shocks and shock-related structures and plasma compression is significant. The effective reconnection rate increases fr…
▽ More
Properties of plasmoid-dominated turbulent reconnection in a low-$β$ background plasma are investigated by resistive magnetohydrodynamic (MHD) simulations. In the $β_{\rm in} < 1$ regime, where $β_{\rm in}$ is plasma $β$ in the inflow region, the reconnection site is dominated by shocks and shock-related structures and plasma compression is significant. The effective reconnection rate increases from $0.01$ to $0.02$ as $β_{\rm in}$ decreases. We hypothesize that plasma compression allows faster reconnection rate, and then we estimate a speed-up factor, based on a compressible MHD theory. We validate our prediction by a series of MHD simulations. These results suggest that the plasmoid-dominated reconnection can be twice faster than expected in the $β\ll 1$ environment in a solar corona.
△ Less
Submitted 22 April, 2020;
originally announced April 2020.
-
A Multistate Low-dissipation Advection Upstream Splitting Method for Ideal Magnetohydrodynamics
Authors:
Takashi Minoshima,
Keiichi Kitamura,
Takahiro Miyoshi
Abstract:
We develop a new numerical scheme for ideal magnetohydrodynamic (MHD) simulations, which is robust against one- and multi-dimensional shocks, and is accurate for low Mach number flows and discontinuities. The scheme belongs to a family of the advection upstream splitting method employed in computational aerodynamics, and it splits the inviscid flux in MHD equations into advection, pressure, and ma…
▽ More
We develop a new numerical scheme for ideal magnetohydrodynamic (MHD) simulations, which is robust against one- and multi-dimensional shocks, and is accurate for low Mach number flows and discontinuities. The scheme belongs to a family of the advection upstream splitting method employed in computational aerodynamics, and it splits the inviscid flux in MHD equations into advection, pressure, and magnetic tension parts, and then individually evaluates mass, pressure, and magnetic tension fluxes at the interface of a computational cell. The mass flux is designed to avoid numerical shock instability in multidimension, while preserving contact discontinuity. The pressure flux possesses a proper scaling for low Mach number flows, allowing reliable simulations of nearly incompressible flows. The magnetic tension flux is built to be consistent with the HLLD approximate Riemann solver to preserve rotational discontinuity. We demonstrate various benchmark tests to verify the novel performance of the scheme. Our results indicate that the scheme must be a promising tool to tackle astrophysical systems that include both low and high Mach number flows, as well as magnetic field inhomogeneities.
△ Less
Submitted 16 April, 2020;
originally announced April 2020.
-
A high-order weighted finite difference scheme with a multi-state approximate Riemann solver for divergence-free magnetohydrodynamic simulations
Authors:
Takashi Minoshima,
Takahiro Miyoshi,
Yosuke Matsumoto
Abstract:
We design a conservative finite difference scheme for ideal magnetohydrodynamic simulations that attains high-order accuracy, shock-capturing, and divergence-free condition of the magnetic field. The scheme interpolates pointwise physical variables from computational nodes to midpoints through a high-order nonlinear weighted average. The numerical flux is evaluated at the midpoint by a multi-state…
▽ More
We design a conservative finite difference scheme for ideal magnetohydrodynamic simulations that attains high-order accuracy, shock-capturing, and divergence-free condition of the magnetic field. The scheme interpolates pointwise physical variables from computational nodes to midpoints through a high-order nonlinear weighted average. The numerical flux is evaluated at the midpoint by a multi-state approximate Riemann solver for correct upwinding, and its spatial derivative is approximated by a high-order linear central difference to update the variables with designed order of accuracy and conservation. The magnetic and electric fields are defined at staggered grid points employed in the Constrained Transport (CT) method by Evans & Hawley (1988). We propose a new CT variant, in which the staggered electric field is evaluated so as to be consistent with the base one-dimensional Riemann solver and the staggered magnetic field is updated to be divergence-free as designed high-order finite difference representation. We demonstrate various benchmark tests to measure the performance of the present scheme. We discuss the effect of the choice of interpolation methods, Riemann solvers, and the treatment for the divergence-free condition on the quality of numerical solutions in detail.
△ Less
Submitted 16 April, 2019; v1 submitted 12 March, 2019;
originally announced March 2019.
-
A new HLLD Riemann solver with Boris correction for reducing Alfvén speed
Authors:
Tomoaki Matsumoto,
Takahiro Miyoshi,
Shinsuke Takasao
Abstract:
A new Riemann solver is presented for the ideal magnetohydrodynamics (MHD) equations with the so-called Boris correction. The Boris correction is applied to reduce wave speeds, avoiding an extremely small timestep in MHD simulations. The proposed Riemann solver, Boris-HLLD, is based on the HLLD solver. As done by the original HLLD solver, (1) the Boris-HLLD solver has four intermediate states in t…
▽ More
A new Riemann solver is presented for the ideal magnetohydrodynamics (MHD) equations with the so-called Boris correction. The Boris correction is applied to reduce wave speeds, avoiding an extremely small timestep in MHD simulations. The proposed Riemann solver, Boris-HLLD, is based on the HLLD solver. As done by the original HLLD solver, (1) the Boris-HLLD solver has four intermediate states in the Riemann fan when left and right states are given, (2) it resolves the contact discontinuity, Alfvén waves, and fast waves, and (3) it satisfies all the jump conditions across shock waves and discontinuities except for slow shock waves. The results of a shock tube problem indicate that the scheme with the Boris-HLLD solver captures contact discontinuities sharply and it exhibits shock waves without any overshoot when using the minmod limiter. The stability tests show that the scheme is stable when $|u| \lesssim 0.5c$ for a low Alfvén speed ($V_A \lesssim c$), where $u$, $c$, and $V_A$ denote the gas velocity, speed of light, and Alfvén speed, respectively. For a high Alfvén speed ($V_A \gtrsim c$), where the plasma beta is relatively low in many cases, the stable region is large, $|u| \lesssim (0.6-1) c$. We discuss the effect of the Boris correction on physical quantities using several test problems. The Boris-HLLD scheme can be useful for problems with supersonic flows in which regions with a very low plasma beta appear in the computational domain.
△ Less
Submitted 2 March, 2019; v1 submitted 7 February, 2019;
originally announced February 2019.
-
X-ray response evaluation in subpixel level for X-ray SOI pixel detectors
Authors:
Kousuke Negishi,
Takayoshi Kohmura,
Kouichi Hagino,
Taku Kogiso,
Kenji Oono,
Keigo Yarita,
Akinori Sasaki,
Koki Tamasawa,
Takeshi G. Tsuru,
Takaaki Tanaka,
Hideaki Matsumura,
Katsuhiro Tachibana,
Hideki Hayashi,
Sodai Harada,
Koji Mori,
Ayaki Takeda,
Yusuke Nishioka,
Nobuaki Takebayashi,
Shoma Yokoyama,
Kohei Fukuda,
Yasuo Arai,
Toshinobu Miyoshi,
Shunji Kishimoto,
Ikuo Kurachi
Abstract:
We have been develo** event-driven SOI Pixel Detectors, named `XRPIX' (X-Ray soiPIXel) based on the silicon-on-insulator (SOI) pixel technology, for the future X-ray astronomical satellite with wide band coverage from 0.5 keV to 40 keV. XRPIX has event trigger output function at each pixel to acquire a good time resolution of a few $μ\rm s$ and has Correlated Double Sampling function to reduce e…
▽ More
We have been develo** event-driven SOI Pixel Detectors, named `XRPIX' (X-Ray soiPIXel) based on the silicon-on-insulator (SOI) pixel technology, for the future X-ray astronomical satellite with wide band coverage from 0.5 keV to 40 keV. XRPIX has event trigger output function at each pixel to acquire a good time resolution of a few $μ\rm s$ and has Correlated Double Sampling function to reduce electric noises. The good time resolution enables the XRPIX to reduce Non X-ray Background in the high energy band above 10\,keV drastically by using anti-coincidence technique with active shield counters surrounding XRPIX. In order to increase the soft X-ray sensitivity, it is necessary to make the dead layer on the X-ray incident surface as thin as possible. Since XRPIX1b, which is a device at the initial stage of development, is a front-illuminated (FI) type of XRPIX, low energy X-ray photons are absorbed in the 8 $\rm μ$m thick circuit layer, lowering the sensitivity in the soft X-ray band. Therefore, we developed a back-illuminated (BI) device XRPIX2b, and confirmed high detection efficiency down to 2.6 keV, below which the efficiency is affected by the readout noise. In order to further improve the detection efficiency in the soft X-ray band, we developed a back-illuminated device XRPIX3b with lower readout noise. In this work, we irradiated 2--5 keV X-ray beam collimated to 4 $\rm μm φ$ to the sensor layer side of the XRPIX3b at 6 $\rm μm$ pitch. In this paper, we reported the uniformity of the relative detection efficiency, gain and energy resolution in the subpixel level for the first time. We also confirmed that the variation in the relative detection efficiency at the subpixel level reported by Matsumura et al. has improved.
△ Less
Submitted 25 October, 2018;
originally announced October 2018.
-
Proton Radiation Damage Experiment for X-Ray SOI Pixel Detectors
Authors:
Keigo Yarita,
Takayoshi Kohmura,
Kouichi Hagino,
Taku Kogiso,
Kenji Oono,
Kousuke Negishi,
Koki Tamasawa,
Akinori Sasaki,
Satoshi Yoshiki,
Takeshi Go Tsuru,
Takaaki Tanaka,
Hideaki Matsumura,
Katsuhiro Tachibana,
Hideki Hayashi,
Sodai Harada,
Ayaki Takeda,
Koji Mori,
Yusuke Nishioka,
Nobuaki Takebayashi,
Shoma Yokoyama,
Kohei Fukuda,
Yasuo Arai,
Toshinobu Miyoshi,
Ikuo Kurachi,
Tsuyoshi Hamano
, et al. (1 additional authors not shown)
Abstract:
In low earth orbit, there are many cosmic rays composed primarily of high energy protons. These cosmic rays cause surface and bulk radiation effects, resulting in degradation of detector performance. Quantitative evaluation of radiation hardness is essential in development of X-ray detectors for astronomical satellites. We performed proton irradiation experiments on newly developed X-ray detectors…
▽ More
In low earth orbit, there are many cosmic rays composed primarily of high energy protons. These cosmic rays cause surface and bulk radiation effects, resulting in degradation of detector performance. Quantitative evaluation of radiation hardness is essential in development of X-ray detectors for astronomical satellites. We performed proton irradiation experiments on newly developed X-ray detectors called XRPIX based on silicon-on-insulator technology at HIMAC in National Institute of Radiological Sciences. We irradiated 6 MeV protons with a total dose of 0.5 krad, equivalent to 6 years irradiation in orbit. As a result, the gain increases by 0.2% and the energy resolution degrades by 0.5%. Finally we irradiated protons up to 20 krad and found that detector performance degraded significantly at 5 krad. With 5 krad irradiation corresponding to 60 years in orbit, the gain increases by 0.7% and the energy resolution worsens by 10%. By decomposing into noise components, we found that the increase of the circuit noise is dominant in the degradation of the energy resolution.
△ Less
Submitted 22 October, 2018;
originally announced October 2018.
-
Development of Integration-Type Silicon-On-Insulator Monolithic Pixel Detectors by Using a Float Zone Silicon
Authors:
S. Mitsui,
Y. Arai,
T. Miyoshi,
A. Takeda
Abstract:
In this paper, we describe the development of monolithic pixel detectors by using a Silicon-on-Insulator (SOI) technology for X-ray and charged particle applications. The detectors are based on a 0.2 μm CMOS fully depleted SOI process (Lapis Semiconductor Co., Ltd). The SOI wafer consists of a thick high-resistivity substrate for sensing and a thin low resistivity Si layer for CMOS circuits.
We…
▽ More
In this paper, we describe the development of monolithic pixel detectors by using a Silicon-on-Insulator (SOI) technology for X-ray and charged particle applications. The detectors are based on a 0.2 μm CMOS fully depleted SOI process (Lapis Semiconductor Co., Ltd). The SOI wafer consists of a thick high-resistivity substrate for sensing and a thin low resistivity Si layer for CMOS circuits.
We developed the integration-type SOI pixel detector, INTPIX4 mainly for X-ray imaging; it is made of a Float Zone (FZ) or Czochralski (Cz) silicon wafer. Since 2005, Cz SOI detectors were used initially. After 2011, FZ SOI detectors were successfully fabricated. In this paper, we state recent progresses and test results of the SOI monolithic pixel detector using a FZ silicon and compare them with the results obtained using the Cz detector.
△ Less
Submitted 10 April, 2018;
originally announced April 2018.
-
Development of high-speed X-ray imaging system for SOI pixel detector
Authors:
Ryutaro Nishimura,
Yasuo Arai,
Toshinobu Miyoshi,
Keiichi Hirano,
Shunji Kishimoto,
Ryo Hashimoto
Abstract:
We are now develo** new X-ray imaging system by using Silicon-On-Insulator (SOI) Pixel Detectors. The SOI detector is a monolithic radiation imaging detector based on a 0.2um FD-SOI CMOS process. Special additional process steps are also developed to create fully depleted sensing region of 50~500um thick. SOI detector has up to mega pixels, so development of high speed Data Acquisition (DAQ) sys…
▽ More
We are now develo** new X-ray imaging system by using Silicon-On-Insulator (SOI) Pixel Detectors. The SOI detector is a monolithic radiation imaging detector based on a 0.2um FD-SOI CMOS process. Special additional process steps are also developed to create fully depleted sensing region of 50~500um thick. SOI detector has up to mega pixels, so development of high speed Data Acquisition (DAQ) system is very important in conducting experiments. We have developed readout board named SEABAS2 (Soi EvAluation BoArd with Sitcp 2) for SOI detector. The SEABAS2 board has 16 channels of 65 MSPS ADCs, 4ch DAC, FPGAs and Gigabit Ethernet I/F. To achieve high throughput of the DAQ, we aggressively adopt parallel processing (data taking and storing) and implement FIFO buffers in software. DAQ throughput in previous DAQ system was 6 Hz (41 Mbps) for INTPIX4 detector which has 423 kpixels of 17 um square. With newly developed system, we could improve this rate to 90 Hz (613 Mbps). To take X-ray images for practical purpose such as 3D CT, user have to control the peripheral devices (moving stage, beam shutter, monitoring devices etc.) while taking images. To ease such data taking, we also implemented automatic control function of peripheral devices. Introduction of SOI detectors, the detail of the DAQ system and experimental results are presented.
△ Less
Submitted 26 March, 2018;
originally announced March 2018.
-
Magnetohydrodynamic Simulation Code CANS+: Assessments and Applications
Authors:
Yosuke Matsumoto,
Yuta Asahina,
Yuki Kudoh,
Tomohisa Kawashima,
** Matsumoto,
Hiroyuki R. Takahashi,
Takashi Minoshima,
Seiji Zenitani,
Takahiro Miyoshi,
Ryoji Matsumoto
Abstract:
We present a new magnetohydrodynamic (MHD) simulation code with the aim of providing accurate numerical solutions to astrophysical phenomena where discontinuities, shock waves, and turbulence are inherently important. The code implements the HLLD approximate Riemann solver, the fifth-order-monotonicity-preserving interpolation (MP5) scheme, and the hyperbolic divergence cleaning method for a magne…
▽ More
We present a new magnetohydrodynamic (MHD) simulation code with the aim of providing accurate numerical solutions to astrophysical phenomena where discontinuities, shock waves, and turbulence are inherently important. The code implements the HLLD approximate Riemann solver, the fifth-order-monotonicity-preserving interpolation (MP5) scheme, and the hyperbolic divergence cleaning method for a magnetic field. This choice of schemes significantly improved numerical accuracy and stability, and saved computational costs in multidimensional problems. Numerical tests of one- and two-dimensional problems showed the advantages of using the high-order scheme by comparing with results from a standard second-order TVD MUSCL scheme. The present code enabled us to explore long-term evolution of a three-dimensional accretion disk around a black hole, in which compressible MHD turbulence caused continuous mass accretion via nonlinear growth of the magneto-rotational instability (MRI). Numerical tests with various computational cell sizes exhibited a convergent picture of the early nonlinear growth of the MRI in a global model, and indicated that the MP5 scheme has more than twice the resolution of the MUSCL scheme in practical applications.
△ Less
Submitted 18 August, 2019; v1 submitted 6 November, 2016;
originally announced November 2016.
-
Boosting Magnetic Reconnection by Viscosity and Thermal Conduction
Authors:
Takashi Minoshima,
Takahiro Miyoshi,
Shinsuke Imada
Abstract:
Nonlinear evolution of magnetic reconnection is investigated by means of magnetohydrodynamic simulations including uniform resistivity, uniform viscosity, and anisotropic thermal conduction. When viscosity exceeds resistivity (the magnetic Prandtl number Prm > 1), the viscous dissipation dominates outflow dynamics and leads to the decrease in the plasma density inside a current sheet. The low-dens…
▽ More
Nonlinear evolution of magnetic reconnection is investigated by means of magnetohydrodynamic simulations including uniform resistivity, uniform viscosity, and anisotropic thermal conduction. When viscosity exceeds resistivity (the magnetic Prandtl number Prm > 1), the viscous dissipation dominates outflow dynamics and leads to the decrease in the plasma density inside a current sheet. The low-density current sheet supports the excitation of the vortex. The thickness of the vortex is broader than that of the current for Prm > 1. The broader vortex flow more efficiently carries the upstream magnetic flux toward the reconnection region, and consequently boosts the reconnection. The reconnection rate increases with viscosity provided that thermal conduction is fast enough to take away the thermal energy increased by the viscous dissipation (the fluid Prandtl number Pr < 1). The result suggests the need to control the Prandtl numbers for the reconnection against the conventional resistive model.
△ Less
Submitted 25 July, 2016; v1 submitted 11 July, 2016;
originally announced July 2016.
-
Development of the Pixelated Photon Detector Using Silicon on Insulator Technology for TOF-PET
Authors:
Akihiro Koyama,
Kenji Shimazoe,
Hiroyuki Takahashi,
Tadashi Orita,
Yasuo Arai,
Ikuo Kurachi,
Toshinobu Miyoshi,
Daisuke Nio,
Ryutaro Hamasaki
Abstract:
To measure light emission pattern in scintillator, higher sensitivity and faster response are required to photo detector. Such as single photon avalanche diode (SPAD), conventional pixelated photo detector is operated at Geiger avalanche multiplication. However higher gain of SPAD seems very attractive, photon detection efficiency per unit area is low. This weak point is mainly caused by Geiger av…
▽ More
To measure light emission pattern in scintillator, higher sensitivity and faster response are required to photo detector. Such as single photon avalanche diode (SPAD), conventional pixelated photo detector is operated at Geiger avalanche multiplication. However higher gain of SPAD seems very attractive, photon detection efficiency per unit area is low. This weak point is mainly caused by Geiger avalanche mechanism.
To overcome these difficulties, we designed Pixelated Linear Avalanche Integration Detector using Silicon on Insulator technology (SOI-Plaid). To avoid dark count noise and dead time comes from quench circuit, we are planning to use APD in linear multiplication mode. SOI technology enables laminating readout circuit and APD layer, and high-speed and low-noise signal reading regardless smaller gain of linear APD. This study shows design of linear APD by using SOI fabrication process. We designed test element group (TEG) of linear APD and inspected optimal structure of linear APD.
△ Less
Submitted 23 July, 2015;
originally announced July 2015.
-
Compensation for TID Damage in SOI Pixel Devices
Authors:
Naoshi Tobita,
Shunsuke Honda,
Kazuhiko Hara,
Wataru Aoyagi,
Yasuo Arai,
Toshinobu Miyoshi,
Ikuo Kurachi,
Takaki Hatsui,
Togo Kudo,
Kazuo Kobayashi
Abstract:
We are investigating adaption of SOI pixel devices for future high energy physic(HEP) experiments. The pixel sensors are required to be operational in very severe radiation environment. Most challenging issue in the adoption is the TID (total ionizing dose) damage where holes trapped in oxide layers affect the operation of nearby transistors. We have introduced a second SOI layer - SOI2 beneath th…
▽ More
We are investigating adaption of SOI pixel devices for future high energy physic(HEP) experiments. The pixel sensors are required to be operational in very severe radiation environment. Most challenging issue in the adoption is the TID (total ionizing dose) damage where holes trapped in oxide layers affect the operation of nearby transistors. We have introduced a second SOI layer - SOI2 beneath the BOX (Buried OXide) layer - in order to compensate for the TID effect by applying a negative voltage to this electrode to cancel the effect caused by accumulated positive holes. In this paper, the TID effects caused by Co gamma-ray irradiation are presented based on the transistor characteristics measurements. The irradiation was carried out in various biasing conditions to investigate hole accumulation dependence on the potential configurations. We also compare the data with samples irradiated with X-ray. Since we observed a fair agreement between the two irradiation datasets, the TID effects have been investigated in a wide dose range from 100~Gy to 2~MGy.
△ Less
Submitted 21 July, 2015;
originally announced July 2015.
-
Characteristics of Non-Irradiated and Irradiated Double SOI Integration Type Sensor
Authors:
Mari Asano,
Kazuhiko Hara,
Daisuke Sekigawa,
Shunsuke Honda,
Naoshi Tobita,
Yasuo Arai,
Toshinobu Miyoshi,
Ikuo Kurachi
Abstract:
We are develo** monolithic pixel sensors based on a 0.2 $μ$m fully-depleted Silicon-on-Insulator (SOI) technology for HEP experiment applications. The total ionizing dose (TID) effect is the major issue in the applications for hard radiation environments in HEP experiments. To compensate for TID damage, we have introduced a Double SOI structure which has a Middle Silicon layer (SOI2 layer) in ad…
▽ More
We are develo** monolithic pixel sensors based on a 0.2 $μ$m fully-depleted Silicon-on-Insulator (SOI) technology for HEP experiment applications. The total ionizing dose (TID) effect is the major issue in the applications for hard radiation environments in HEP experiments. To compensate for TID damage, we have introduced a Double SOI structure which has a Middle Silicon layer (SOI2 layer) in addition. We studied the recovery from TID damage induced by $\mathrm{^{60}Co}~γ$'s and other characteristics of an Integration-type Double SOI sensor. The Double SOI sensor irradiated to 100 kGy showed a response for IR laser similar to of a non-irradiated sensor when we applied a negative voltage to the SOI2 layer. We conclude that the Double SOI sensor is radiation hard enough to be used in HEP experiments in harsh radiation environments such as at Bell II or ILC.
△ Less
Submitted 20 July, 2015;
originally announced July 2015.
-
DAQ Development for Silicon-On-Insulator Pixel detectors
Authors:
Ryutaro Nishimura,
Yasuo Arai,
Toshinobu Miyoshi
Abstract:
We are develo** DAQ for Si-pixel detectors by using a Slicon-On-Insulator (SOI) technology. This DAQ consists of firmware works on SEABAS (Soi EvAluation BoArd with Sitcp) DAQ board and software works on PC. We have been working on the development of firmware/software. Now we accomplished to speed up the readout (~90Hz) and to add a function for frame rate control. This is the report of our deve…
▽ More
We are develo** DAQ for Si-pixel detectors by using a Slicon-On-Insulator (SOI) technology. This DAQ consists of firmware works on SEABAS (Soi EvAluation BoArd with Sitcp) DAQ board and software works on PC. We have been working on the development of firmware/software. Now we accomplished to speed up the readout (~90Hz) and to add a function for frame rate control. This is the report of our development work for the High Speed DAQ system.
△ Less
Submitted 17 July, 2015;
originally announced July 2015.
-
Exploring properties of the integrating pixels
Authors:
Piotr Julian Kapusta,
Yasuo Arai,
Szymon Bugiel,
Roma Dasgupta,
Sebastian Glab,
Marek Idzik,
Wojciech Kucewicz,
Toshinobu Miyoshi,
Michal Turala
Abstract:
This paper presents some observations and ideas collected during the tests of the SOI sensors, based on the integration type pixels. First, it contains a rough analysis of the Correlated Double Sampling filtering properties with respect to different noise sources and long sampling intervals, which are typical for the pixels under consideration. Second, results of the pixel leakage current measurem…
▽ More
This paper presents some observations and ideas collected during the tests of the SOI sensors, based on the integration type pixels. First, it contains a rough analysis of the Correlated Double Sampling filtering properties with respect to different noise sources and long sampling intervals, which are typical for the pixels under consideration. Second, results of the pixel leakage current measurements in the pix_2012 and DIPIX pixel detector chips are presented.
△ Less
Submitted 3 July, 2015;
originally announced July 2015.
-
Transboundary Secondary Organic Aerosol in Western Japan: An Observed Limitation of the f44 Oxidation Indicator
Authors:
Satoshi Irei,
Akinori Takami,
Yasuhiro Sadanaga,
Takao Miyoshi,
Tekemitsu Arakaki,
Kei Sato,
Naoki Kaneyasu,
Hiroshi Bandow,
Shiro Hatakeyama
Abstract:
To obtain evidence for secondary organic aerosol formation during the long range transport of air masses over the East China Sea, we conducted field measurements in March 2012 at the Fukue atmospheric monitoring station, Nagasaki, in western Japan. The relative abundance of m/z 44 in fine organic aerosol mass spectra (f44) was measured by an Aerodyne aerosol chemical speciation monitor. The stable…
▽ More
To obtain evidence for secondary organic aerosol formation during the long range transport of air masses over the East China Sea, we conducted field measurements in March 2012 at the Fukue atmospheric monitoring station, Nagasaki, in western Japan. The relative abundance of m/z 44 in fine organic aerosol mass spectra (f44) was measured by an Aerodyne aerosol chemical speciation monitor. The stable carbon isotope ratio (d13C) of low volatile water soluble organic carbon (LV-WSOC) in the daily filter samples of total suspended particulate matter was also analyzed using an elemental analyzer coupled with an isotope ratio mass spectrometer. Additionally, in situ measurements of NOx and NOy were performed using NOx and NOy analyzers. The measurements showed that, unlike the systematic trends observed in a previous field study, a scatter plot for d13C of LV-WSOC versus f44 indicated a random variation. Comparison of f44 with the photochemical age estimated by the NOx to NOy ratio revealed that the f44 values distributing around 0.2 likely reached a saturation level already and the f44 values were significantly lower than the observed f44, approximately 0.3, at Hedo in the previous study. These findings imply that the saturation point of f44, and the use of f44 as an oxidation indicator, is case dependent.
△ Less
Submitted 28 April, 2015;
originally announced April 2015.
-
Magnetohydrodynamic structure of a plasmoid in fast reconnection in low-beta plasmas
Authors:
Seiji Zenitani,
Takahiro Miyoshi
Abstract:
Plasmoid structures in fast reconnection in low-beta plasmas are investigated by two-dimensional magnetohydrodynamic simulations. A high-resolution shock-capturing code enables us to explore a variety of shock structures: vertical slow shocks behind the plasmoid, another slow shocks in the outer-region, and the shock-reflection in the front side. The Kelvin-Helmholtz-like turbulence is also found…
▽ More
Plasmoid structures in fast reconnection in low-beta plasmas are investigated by two-dimensional magnetohydrodynamic simulations. A high-resolution shock-capturing code enables us to explore a variety of shock structures: vertical slow shocks behind the plasmoid, another slow shocks in the outer-region, and the shock-reflection in the front side. The Kelvin-Helmholtz-like turbulence is also found inside the plasmoid. It is concluded that these shocks are rigorous features in reconnection in low-beta plasmas, where the reconnection jet speed or the upstream Alfven speed exceeds the sound speed.
△ Less
Submitted 13 October, 2014; v1 submitted 11 January, 2011;
originally announced January 2011.
-
Belle II Technical Design Report
Authors:
T. Abe,
I. Adachi,
K. Adamczyk,
S. Ahn,
H. Aihara,
K. Akai,
M. Aloi,
L. Andricek,
K. Aoki,
Y. Arai,
A. Arefiev,
K. Arinstein,
Y. Arita,
D. M. Asner,
V. Aulchenko,
T. Aushev,
T. Aziz,
A. M. Bakich,
V. Balagura,
Y. Ban,
E. Barberio,
T. Barvich,
K. Belous,
T. Bergauer,
V. Bhardwaj
, et al. (387 additional authors not shown)
Abstract:
The Belle detector at the KEKB electron-positron collider has collected almost 1 billion Y(4S) events in its decade of operation. Super-KEKB, an upgrade of KEKB is under construction, to increase the luminosity by two orders of magnitude during a three-year shutdown, with an ultimate goal of 8E35 /cm^2 /s luminosity. To exploit the increased luminosity, an upgrade of the Belle detector has been pr…
▽ More
The Belle detector at the KEKB electron-positron collider has collected almost 1 billion Y(4S) events in its decade of operation. Super-KEKB, an upgrade of KEKB is under construction, to increase the luminosity by two orders of magnitude during a three-year shutdown, with an ultimate goal of 8E35 /cm^2 /s luminosity. To exploit the increased luminosity, an upgrade of the Belle detector has been proposed. A new international collaboration Belle-II, is being formed. The Technical Design Report presents physics motivation, basic methods of the accelerator upgrade, as well as key improvements of the detector.
△ Less
Submitted 1 November, 2010;
originally announced November 2010.
