Showing 1–46 of 46 results for author: Kirk, A

Experimental conditions to suppress edge localised modes by magnetic perturbations in the ASDEX Upgrade tokamak

Authors: W. Suttrop, A. Kirk, V. Bobkov, M. Cavedon, M. Dunne, R. M. McDermott, H. Meyer, R. Nazikian, C. Paz-Soldan, D. A. Ryan, E. Viezzer, M. Willensdorfer

Abstract: Access conditions for full suppression of Edge Localised Modes (ELMs) by Magnetic Perturbations (MP) in low density high confinement mode (H-mode) plasmas are studied in the ASDEX Upgrade tokamak. The main empirical requirements for full ELM suppression in our experiments are: 1. The poloidal spectrum of the MP must be aligned for best plasma response from weakly stable kink-modes, which amplify t… ▽ More Access conditions for full suppression of Edge Localised Modes (ELMs) by Magnetic Perturbations (MP) in low density high confinement mode (H-mode) plasmas are studied in the ASDEX Upgrade tokamak. The main empirical requirements for full ELM suppression in our experiments are: 1. The poloidal spectrum of the MP must be aligned for best plasma response from weakly stable kink-modes, which amplify the perturbation, 2. The plasma edge density must be below a critical value, $3.3 \times 10^{19}$~m$^{-3}$. The edge collisionality is in the range $ν^*_i = 0.15-0.42$ (ions) and $ν^*_e = 0.15-0.25$ (electrons). However, our data does not show that the edge collisionality is the critical parameter that governs access to ELM suppression. 3. The pedestal pressure must be kept sufficiently low to avoid destabilisation of small ELMs. This requirement implies a systematic reduction of pedestal pressure of typically 30\% compared to unmitigated ELMy H-mode in otherwise similar plasmas. 4. The edge safety factor $q_{95}$ lies within a certain window. Within the range probed so far, $q_{95}=3.5-4.2$, one such window, $q_{95}=3.57-3.95$ has been identified. Within the range of plasma rotation encountered so far, no apparent threshold of plasma rotation for ELM suppression is found. This includes cases with large cross field electron flow in the entire pedestal region, for which two-fluid MHD models predict that the resistive plasma response to the applied MP is shielded. △ Less

Submitted 29 June, 2018; v1 submitted 3 April, 2018; originally announced April 2018.

Quiescence near the X-point of MAST measured by high speed visible imaging

Authors: N. R. Walkden, J. Harrison, S. A. Silburn, T. Farley, S. S. Henderson, A. Kirk, F. Militello, the MAST Team

Abstract: Using high speed imaging of the divertor volume, the region close to the X-point in MAST is shown to be quiescent. This is confirmed by three different analysis techniques and the quiescent X-point region (QXR) spans from the separatrix to the 1.02 flux surface. Local reductions to the atomic density and effects associated with the camera viewing geometry are ruled out as causes of the QXR, leavin… ▽ More Using high speed imaging of the divertor volume, the region close to the X-point in MAST is shown to be quiescent. This is confirmed by three different analysis techniques and the quiescent X-point region (QXR) spans from the separatrix to the 1.02 flux surface. Local reductions to the atomic density and effects associated with the camera viewing geometry are ruled out as causes of the QXR, leaving quiescence in the local plasma conditions as being the most likely cause. The QXR is found to be ubiquitous across a significant operational space in MAST including L-mode and H-mode discharges across wide ranges of line averaged density, plasma current and NBI power. When mapped to the divertor target the QXR occupies approximately an e-folding length of the heat-flux profile, containing approximately 60% of the total heat flux to the target, and also shows a tendency towards higher frequency shorter lived fluctuations in the ion-saturation current. This is consistent with short- lived divertor localised filamentary structures observed further down the outer divertor leg in the camera images, and suggests a complex multi-region picture of filamentary transport in the divertor. △ Less

Submitted 20 June, 2017; originally announced June 2017.

Three dimensional boundary displacement due to stable ideal kink modes excited by external n=2 magnetic perturbations

Authors: M. Willensdorfer, E. Strumberger, W. Suttrop, M. Dunne, R. Fischer, G. Birkenmeier, D. Brida, M. Cavedon, S. S. Denk, V. Igochine, L. Giannone, A. Kirk, J. Kirschner, A. Medvedeva, T. Odstrcil, D. A. Ryan, the ASDEX Upgrade Team, the EUROfusion MST1 Team

Abstract: In low-collisionality scenarios exhibiting mitigation of edge localized modes (ELMs), stable ideal kink modes at the edge are excited by externally applied magnetic perturbation (MP)-fields. In ASDEX Upgrade these modes can cause three-dimensional (3D) boundary displacements up to the centimeter range. These displacements have been measured using toroidally localized high resolution diagnostics an… ▽ More In low-collisionality scenarios exhibiting mitigation of edge localized modes (ELMs), stable ideal kink modes at the edge are excited by externally applied magnetic perturbation (MP)-fields. In ASDEX Upgrade these modes can cause three-dimensional (3D) boundary displacements up to the centimeter range. These displacements have been measured using toroidally localized high resolution diagnostics and rigidly rotating n = 2 MP-fields with various applied poloidal mode spectra. These measurements are compared to non-linear 3D ideal magnetohydrodynamics (MHD) equilibria calculated by VMEC. Comprehensive comparisons have been conducted, which consider for instance plasma movements due to the position control system, attenuation due to internal conductors and changes in the edge pressure profiles. VMEC accurately reproduces the amplitude of the displacement and its dependencies on the applied poloidal mode spectra. Quantitative agreement is found around the low field side (LFS) midplane. The response at the plasma top is qualitatively compared. The measured and predicted displacements at the plasma top maximize when the applied spectra is optimized for ELM-mitigation. The predictions from the vacuum modeling generally fails to describe the displacement at the LFS midplane as well as at the plasma top. When the applied mode spectra is set to maximize the displacement, VMEC and the measurements clearly surpass the predictions from the vacuum modeling by a factor of four. Minor disagreements between VMEC and the measurements are discussed. This study underlines the importance of the stable ideal kink modes at the edge for the 3D boundary displacement in scenarios relevant for ELM-mitigation. △ Less

Submitted 24 July, 2017; v1 submitted 10 February, 2017; originally announced February 2017.

Comments: 22 pages, 12 figure, for submission to nuclear fusion

Journal ref: Nucl. Fusion 57 (2017) 116047 (12pp)

Overview of recent physics results from MAST

Authors: A Kirk, J Adamek, RJ Akers, S Allan, L Appel, F Arese Lucini, M Barnes, T Barrett, N Ben Ayed, W Boeglin, J Bradley, P K Browning, J Brunner, P Cahyna, M Carr, F Casson, M Cecconello, C Challis, IT Chapman, S Chapman, S Conroy, N Conway, WA Cooper, M Cox, N Crocker , et al. (138 additional authors not shown)

Abstract: New results from MAST are presented that focus on validating models in order to extrapolate to future devices. Measurements during start-up experiments have shown how the bulk ion temperature rise scales with the square of the reconnecting field. During the current ramp up models are not able to correctly predict the current diffusion. Experiments have been performed looking at edge and core turbu… ▽ More New results from MAST are presented that focus on validating models in order to extrapolate to future devices. Measurements during start-up experiments have shown how the bulk ion temperature rise scales with the square of the reconnecting field. During the current ramp up models are not able to correctly predict the current diffusion. Experiments have been performed looking at edge and core turbulence. At the edge detailed studies have revealed how filament characteristic are responsible for determining the near and far SOL density profiles. In the core the intrinsic rotation and electron scale turbulence have been measured. The role that the fast ion gradient has on redistributing fast ions through fishbone modes has led to a redesign of the neutral beam injector on MAST Upgrade. In H-mode the turbulence at the pedestal top has been shown to be consistent with being due to electron temperature gradient modes. A reconnection process appears to occur during ELMs and the number of filaments released determines the power profile at the divertor. Resonant magnetic perturbations can mitigate ELMs provided the edge peeling response is maximised and the core kink response minimised. The mitigation of intrinsic error fields with toroidal mode number n>1 has been shown to be important for plasma performance. △ Less

Submitted 18 November, 2016; originally announced November 2016.

Comments: 34 pages, 10 figures. This is an author-created, un-copyedited version of an article submitted for publication in Nuclear Fusion. IoP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

ELM control with RMP: plasma response models and the role of edge peeling response

Authors: Yueqiang Liu, C. J. Ham, A. Kirk, Li Li, A. Loarte, D. A. Ryan, Youwen Sun, W. Suttrop, Xu Yang, Lina Zhou

Abstract: Resonant magnetic perturbations (RMP) have extensively been demonstrated as a plausible technique for mitigating or suppressing large edge localized modes (ELMs). Associated with this is a substantial amount of theory and modelling efforts during recent years. Various models describing the plasma response to the RMP fields have been proposed in the literature, and are briefly reviewed in this work… ▽ More Resonant magnetic perturbations (RMP) have extensively been demonstrated as a plausible technique for mitigating or suppressing large edge localized modes (ELMs). Associated with this is a substantial amount of theory and modelling efforts during recent years. Various models describing the plasma response to the RMP fields have been proposed in the literature, and are briefly reviewed in this work. Despite their simplicity, linear response models can provide alternative criteria, than the vacuum field based criteria, for guiding the choice of the coil configurations to achieve the best control of ELMs. The role of the edge peeling response to the RMP fields is illustrated as a key indicator for the ELM mitigation in low collisionality plasmas, in various tokamak devices. △ Less

Submitted 5 July, 2016; originally announced July 2016.

Comments: 32 pages, 10 figures. This is an author-created, un-copyedited version of an article submitted for publication in Plasma Physics and Controlled Fusion. IoP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Plasma response measurements of external magnetic perturbations using electron cyclotron emission and comparisons to 3D ideal MHD equilibrium

Authors: M. Willensdorfer, S. S. Denk, E. Strumberger, W. Suttrop, B. Vanovac, D. Brida, M. Cavedon, I. Classen, M. Dunne, S. Fietz, R. Fischer, A. Kirk, F. M. Laggner, Y. Q. Liu, T. Odstrcil, D. A. Ryan, E. Viezzer, H. Zohm, I. C. Luhmann

Abstract: The plasma response from an external n = 2 magnetic perturbation field in ASDEX Upgrade has been measured using mainly electron cyclotron emission (ECE) diagnostics and a rigid rotating field. To interpret ECE and ECE-imaging (ECE-I) measurements accurately, forward modeling of the radiation transport has been combined with ray tracing. The measured data is compared to synthetic ECE data generated… ▽ More The plasma response from an external n = 2 magnetic perturbation field in ASDEX Upgrade has been measured using mainly electron cyclotron emission (ECE) diagnostics and a rigid rotating field. To interpret ECE and ECE-imaging (ECE-I) measurements accurately, forward modeling of the radiation transport has been combined with ray tracing. The measured data is compared to synthetic ECE data generated from a 3D ideal magnetohydrodynamics (MHD) equilibrium calculated by VMEC. The measured amplitudes of the helical displacement around the low field side midplane are in reasonable agreement with the one from the synthetic VMEC diagnostics. Both exceed the prediction from the vacuum field calculations and indicate the presence of a kink response at the edge, which amplifies the perturbation. VMEC and MARS-F have been used to calculate the properties of this kink mode. The poloidal mode structure of the magnetic perturbation of this kink mode at the edge peaks at poloidal mode numbers larger than the resonant components |m| > |nq|, whereas the poloidal mode structure of its displacement is almost resonant |m| ~ |nq|. This is expected from ideal MHD in the proximity of rational surfaces. The displacement measured by ECE-I confirms this resonant response. △ Less

Submitted 4 August, 2016; v1 submitted 30 March, 2016; originally announced March 2016.

Comments: 34 pages, 19 figures. This is an author-created, un-copyedited version of an article submitted for publication in Plasma Physics and Controlled Fusion. IoP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: Plasma Phys. Control. Fusion 58 (2016) 114004 (18pp)

Non-linear modeling of the plasma response to RMPs in ASDEX Upgrade

Authors: F. Orain, M. Hoelzl, E. Viezzer, M. Dunne, M. Becoulet, P. Cahyna, G. T. A. Huijsmans, J. Morales, M. Willensdorfer, W. Suttrop, A. Kirk, S. Pamela, E. Strumberger, S. Guenter, A. Lessig, the ASDEX Upgrade Team, the EUROfusion MST1 Team

Abstract: The plasma response to Resonant Magnetic Perturbations (RMPs) in ASDEX Upgrade is modeled with the non-linear resistive MHD code JOREK, using input profiles that match those of the experiments as closely as possible. The RMP configuration for which Edge Localized Modes are best mitigated in experiments is related to the largest edge kink response observed near the X-point in modeling. On the edge… ▽ More The plasma response to Resonant Magnetic Perturbations (RMPs) in ASDEX Upgrade is modeled with the non-linear resistive MHD code JOREK, using input profiles that match those of the experiments as closely as possible. The RMP configuration for which Edge Localized Modes are best mitigated in experiments is related to the largest edge kink response observed near the X-point in modeling. On the edge resonant surfaces $q = m/n$, the coupling between the m + 2 kink component and the m resonant component is found to induce the amplification of the resonant magnetic perturbation. The ergodicity and the 3D-displacement near the X-point induced by the resonant amplification can only partly explain the density pumpout observed in experiments. △ Less

Submitted 24 February, 2016; originally announced February 2016.

Comments: Submitted to Nuclear Fusion 18 pages (19 pages with Arxiv's compilation formatting), 13 figures

L-mode filament characteristics on MAST as a function of plasma current measured using visible imaging

Authors: A. Kirk, A. J. Thornton, J. R. Harrison, F. Militello, N. R. Walkden

Abstract: Clear filamentary structures are observed at the edge of tokamak plasmas. These filaments are ejected out radially and carry plasma in the far Scrape Off Layer (SOL) region, where they are responsible for producing most of the transport. A study has been performed of the characteristics of the filaments observed in L-mode plasma on MAST, using visible imaging. A comparison has then been made with… ▽ More Clear filamentary structures are observed at the edge of tokamak plasmas. These filaments are ejected out radially and carry plasma in the far Scrape Off Layer (SOL) region, where they are responsible for producing most of the transport. A study has been performed of the characteristics of the filaments observed in L-mode plasma on MAST, using visible imaging. A comparison has then been made with the observed particle and power profiles obtained at the divertor as a function of the plasma current. The radial velocity and to a lesser extent the radial size of the filaments are found to decrease as the plasma current is increased at constant density and input power. The results obtained in this paper on the dependence of the average filament dynamics on plasma current are consistent with the idea that the filaments are responsible for determining the particle profiles at the divertor. △ Less

Submitted 9 February, 2016; originally announced February 2016.

Comments: 24 pages, 17 figures. This is an author-created, un-copyedited version of an article submitted for publication in Plasma Physics and Controlled Fusion. IoP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: 2016 Plasma Phys. Control. Fusion 58 085008

Scrape-off layer ion temperature measurements at the divertor target during type III and type I ELMs in MAST measured by RFEA

Authors: S. Elmore, S. Y. Allan, G. Fishpool, A. Kirk, A. J. Thornton, N. R. Walkden, J. R. Harrison

Abstract: In future nuclear fusion reactors high heat load events, such as edge-localised modes (ELMs), can potentially damage divertor materials and release impurities into the main plasma, limiting plasma performance. The most difficult to handle are type I ELMs since they carry the largest fraction of energy from the plasma and therefore deposit the largest heat flux at the target and on first wall mater… ▽ More In future nuclear fusion reactors high heat load events, such as edge-localised modes (ELMs), can potentially damage divertor materials and release impurities into the main plasma, limiting plasma performance. The most difficult to handle are type I ELMs since they carry the largest fraction of energy from the plasma and therefore deposit the largest heat flux at the target and on first wall materials. Knowing the temperature of the ions released from ELM events is important since it determines the potential sputtering they would cause from plasma facing materials. To make measurements of Ti by retarding field energy analyser (RFEA) during type I ELMs a new operational technique has been used to allow faster measurements to be made; this is called the fast swept technique (FST). △ Less

Submitted 9 February, 2016; originally announced February 2016.

Comments: 20 pages, 12 figures. This is an author-created, un-copyedited version of an article submitted for publication in Plasma Physics and Controlled Fusion. IoP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: Journal of Nuclear Materials Volume 463, August 2015, pp 889-892

Modelling of spatial structure of divertor footprints caused by edge-localized modes mitigated by magnetic perturbations

Authors: Pavel Cahyna, Marina Becoulet, Guido T. A. Huijsmans, Francois Orain, Jorge Morales, Andrew Kirk, Andrew J. Thornton, Stanislas Pamela, Radomir Panek, Matthias Hoelzl

Abstract: Resonant magnetic perturbations (RMPs) can mitigate the edge-localized modes (ELMs), i.e. cause a change of the ELM character towards smaller energy loss and higher frequency. During mitigation a change of the spatial structure of ELM loads on divertor was observed on DIII-D and MAST: the power is deposited predominantly in the footprint structures formed by the magnetic perturbation. In the prese… ▽ More Resonant magnetic perturbations (RMPs) can mitigate the edge-localized modes (ELMs), i.e. cause a change of the ELM character towards smaller energy loss and higher frequency. During mitigation a change of the spatial structure of ELM loads on divertor was observed on DIII-D and MAST: the power is deposited predominantly in the footprint structures formed by the magnetic perturbation. In the present contribution we develop a theory explaining this effect, based on the idea that part of the ELM loss is caused by parallel transport in the homoclinic tangle formed by the magnetic perturbation of the ELM. The modified tangle resulting from the combination of the ELM perturbation and the applied RMP has the expected property of bringing open field lines in the same areas as the tangle from the RMP alone. We show that this explanation is consistent with features of the mitigated ELMs on MAST. We in addition validated our theory by an analysis of simulations of mitigated ELMs using the code JOREK. We produced detailed laminar plots of field lines on the divertor in the JOREK runs with an ELM, an applied RMP, and an ELM mitigated by the presence of the RMP. The results for an ELM clearly show a high-n rotating footprint structure appearing during the nonlinear stage of the ELM, which is not present in the early stage of the ELM. The results for a n=2 RMP from the ELM control coils show the expected n=2 footprint structure. The results for the mitigated ELM show a similar structure, modulated by a higher n perturbation of the ELM, consistent with our theory. △ Less

Submitted 12 January, 2016; originally announced January 2016.

Comments: 13 pages, presented at the 25th IAEA Fusion Energy Conference, St. Petersburg, Russian Federation, October 13-18, 2014, paper TH/P6-1

Pellet refuelling of particle loss due to ELM mitigation with RMPs in the ASDEX Upgrade tokamak at low collisionality

Authors: M Valovič, P T Lang, A Kirk, W Suttrop, M Cavedon, L R Fischer, L Garzotti, L Guimarais, G Kocsis, G Cseh, B Plőckl, T Szepesi, A Thornton, A Mlynek, G Tardini, E Viezzer, R Scannell, E Wolfrum, the ASDEX Upgrade team, the EUROfusion MST1 team

Abstract: The complete refuelling of the plasma density loss (pump-out) caused by mitigation of Edge Localised Modes (ELMs) is demonstrated on the ASDEX Upgrade tokamak. The plasma is refuelled by injection of frozen deuterium pellets and ELMs are mitigated by external resonant magnetic perturbations (RMPs). In this experiment relevant dimensionless parameters, such as relative pellet size, relative RMP amp… ▽ More The complete refuelling of the plasma density loss (pump-out) caused by mitigation of Edge Localised Modes (ELMs) is demonstrated on the ASDEX Upgrade tokamak. The plasma is refuelled by injection of frozen deuterium pellets and ELMs are mitigated by external resonant magnetic perturbations (RMPs). In this experiment relevant dimensionless parameters, such as relative pellet size, relative RMP amplitude and pedestal collisionality are kept at the ITER like values. Refuelling of density pump out requires a factor of two increase of nominal fuelling rate. Energy confinement and pedestal temperatures are not restored to pre-RMP values by pellet refuelling. △ Less

Submitted 7 October, 2015; originally announced October 2015.

Comments: 10 pages, 5 figures. This is an author-created, un-copyedited version of an article submitted for publication in Nuclear Fusion. IoP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: 2016 Nucl. Fusion 56 066009

Characterisation of the L-mode Scrape Off Layer in MAST: decay lengths

Authors: F. Militello, L. Garzotti, J. Harrison, J. T. Omotani, R. Scannell, S. Allan, A. Kirk, I. Lupelli, A. J. Thornton, the MAST team

Abstract: This work presents a detailed characterisation of the MAST Scrape Off Layer in L-mode. Scans in line averaged density, plasma current and toroidal magnetic field were performed. A comprehensive and integrated study of the SOL was allowed by the use of a wide range of diagnostics. In agreement with previous results, an increase of the line averaged density induced a broadening of the midplane densi… ▽ More This work presents a detailed characterisation of the MAST Scrape Off Layer in L-mode. Scans in line averaged density, plasma current and toroidal magnetic field were performed. A comprehensive and integrated study of the SOL was allowed by the use of a wide range of diagnostics. In agreement with previous results, an increase of the line averaged density induced a broadening of the midplane density profile. △ Less

Submitted 15 June, 2015; originally announced June 2015.

Comments: 30 pages, 11 figures

Journal ref: 2016 Nucl. Fusion 56 016006

Nuclear Fusion: Bringing a star down to Earth

Authors: A. Kirk

Abstract: Nuclear fusion offers the potential for being a near limitless energy source by fusing together deuterium and tritium nuclei to form helium inside a plasma burning at 100 million kelvin. However, scientific and engineering challenges remain. This paper describes how such a plasma can be confined on Earth and discusses the similarities and differences with fusion in stars. It focusses on the magnet… ▽ More Nuclear fusion offers the potential for being a near limitless energy source by fusing together deuterium and tritium nuclei to form helium inside a plasma burning at 100 million kelvin. However, scientific and engineering challenges remain. This paper describes how such a plasma can be confined on Earth and discusses the similarities and differences with fusion in stars. It focusses on the magnetic confinement technique and, in particular, the method used in a tokamak. The confinement achieved in the equilibrium state is reviewed and it is shown how the confinement can be too good, leading to explosive instabilities at the plasma edge called Edge Localised modes (ELMs). It is shown how the impact of ELMs can be minimised by the application of magnetic perturbations and discusses the physics behind the penetration of these perturbations into what is ideally a perfect conducting plasma. △ Less

Submitted 31 March, 2015; originally announced March 2015.

Comments: 35 pages, 17 figures

Effect of resonant magnetic perturbations on low collisionality discharges in MAST and a comparison with ASDEX Upgrade

Authors: A. Kirk, W. Suttrop, Yueqiang Liu, I. T. Chapman, P. Cahyna, T. Eich, C. Fuchs, C. Ham, J. R. Harrison, M W. Jakubowski, S. Pamela, M. Peterka, D. Ryan, S. Saarelma, R. Scannell, A. J. Thornton, M. Valovic, B. Sieglin, L. Barrera Orte, M. Willensdorfer, B. Kurzan, R. Fischer

Abstract: Sustained ELM mitigation has been achieved on MAST and AUG using RMPs with a range of toroidal mode numbers over a wide region of low to medium collisionality discharges. The ELM energy loss and peak heat loads at the divertor targets have been reduced. The ELM mitigation phase is typically associated with a drop in plasma density and overall stored energy. In one particular scenario on MAST, by c… ▽ More Sustained ELM mitigation has been achieved on MAST and AUG using RMPs with a range of toroidal mode numbers over a wide region of low to medium collisionality discharges. The ELM energy loss and peak heat loads at the divertor targets have been reduced. The ELM mitigation phase is typically associated with a drop in plasma density and overall stored energy. In one particular scenario on MAST, by carefully adjusting the fuelling it has been possible to counteract the drop in density and to produce plasmas with mitigated ELMs, reduced peak divertor heat flux and with minimal degradation in pedestal height and confined energy. While the applied resonant magnetic perturbation field can be a good indicator for the onset of ELM mitigation on MAST and AUG there are some cases where this is not the case and which clearly emphasise the need to take into account the plasma response to the applied perturbations. The plasma response calculations show that the increase in ELM frequency is correlated with the size of the edge peeling-tearing like response of the plasma and the distortions of the plasma boundary in the X-point region. △ Less

Submitted 24 December, 2014; originally announced December 2014.

Comments: 31 pages, 28 figures. This is an author-created, un-copyedited version of an article submitted for publication in Nuclear Fusion. IoP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: Nuclear Fusion, Vol.55, No.4, April 2015, pp.043011

Impact of Resonant Magnetic Perturbations on the L-H Transition on MAST

Authors: R. Scannell, A. Kirk, M. Carr, J. Hawke, S. S. Henderson, T. O'Gorman, A. Patel, A. Shaw, A. Thornton, the MAST Team

Abstract: The impact of resonant magnetic perturbations (RMPs) on the power required to access H-mode is examined experimentally on MAST. Applying RMP in n=2,3,4 and 6 configurations causes significant delays to the timing of the L-H transition at low applied fields and prevents the transition at high fields. The experiment was primarily performed at RMP fields sufficient to cause moderate increases in ELM… ▽ More The impact of resonant magnetic perturbations (RMPs) on the power required to access H-mode is examined experimentally on MAST. Applying RMP in n=2,3,4 and 6 configurations causes significant delays to the timing of the L-H transition at low applied fields and prevents the transition at high fields. The experiment was primarily performed at RMP fields sufficient to cause moderate increases in ELM frequency, f mitigated/f natural~3. To obtain H-mode with RMPs at this field, an increase of injected beam power is required of at least 50% for n=3 and n=4 RMP and 100% for n=6 RMP. In terms of power threshold, this corresponds to increases of at least 20% for n=3 and n=4 RMPs and 60% for n=6 RMPs. This 'RMP affected' power threshold is found to increase with RMP magnitude above a certain minimum perturbed field, below which there is no impact on the power threshold. Extrapolations from these results indicate large increases in the L-H power threshold will be required for discharges requiring large mitigated ELM frequency. △ Less

Submitted 12 December, 2014; originally announced December 2014.

Comments: 23 pages, 7 figures. This is an author-created, un-copyedited version of an article submitted for publication in Plasma Physics and Controlled Fusion. IOP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: Plasma Physics and Controlled Fusion, Vol.57, No.7, July 2015, ppp.075013

Profile measurements in the plasma edge of MAST using a ball pen probe

Authors: N. R. Walkden, J. Adamek, S. Allan, B. D. Dudson, S. Elmore, G. Fishpool, J. Harrison, A. Kirk, M. Komm

Abstract: The ball pen probe (BPP) technique is used successfully to make profile measurements of plasma potential, electron temperature and radial electric field on the Mega Amp Spherical Tokamak (MAST). The potential profile measured by the BPP is shown to significantly differ from the floating potential both in polarity and profile shape. By combining the BPP potential and the floating potential the elec… ▽ More The ball pen probe (BPP) technique is used successfully to make profile measurements of plasma potential, electron temperature and radial electric field on the Mega Amp Spherical Tokamak (MAST). The potential profile measured by the BPP is shown to significantly differ from the floating potential both in polarity and profile shape. By combining the BPP potential and the floating potential the electron temperature can be measured, which is compared with the Thomson scattering (TS) diagnostic. Excellent agreement between the two diagnostics is obtained when secondary electron emission is accounted for in the floating potential. From the BPP profile an estimate of the radial electric field is extracted which is shown to be of the order ~1kV/m and increases with plasma current. Corrections to the BPP measurement, constrained by the TS comparison, introduce uncertainty into the ER measurements. The uncertainty is most significant in the electric field well inside the separatrix. The electric field is used to estimate toroidal and poloidal rotation velocities from ExB motion. This paper further demonstrates the ability of the ball pen probe to make valuable and important measurements in the boundary plasma of a tokamak. △ Less

Submitted 26 November, 2014; originally announced November 2014.

Comments: 9 pages, 10 figures, submitted to Review of Scientific Instruments

ELM mitigation via rotating resonant magnetic perturbations on MAST

Authors: A. J. Thornton, A. Kirk, P. Cahyna, I. T. Chapman, G. Fishpool, J. R. Harrison, Y. Q. Liu, L. Kripner, M. Peterka, the MAST Team

Abstract: The application of resonant magnetic perturbations (RMPs) produces splitting of the divertor strike point due to the interaction of the RMP field and the plasma field. The application of a rotating RMP field causes the strike point splitting to rotate, distributing the particle and heat flux evenly over the divertor. The RMP coils in MAST have been used to generate a rotating perturbation with a t… ▽ More The application of resonant magnetic perturbations (RMPs) produces splitting of the divertor strike point due to the interaction of the RMP field and the plasma field. The application of a rotating RMP field causes the strike point splitting to rotate, distributing the particle and heat flux evenly over the divertor. The RMP coils in MAST have been used to generate a rotating perturbation with a toroidal mode number n=3. The ELM frequency is doubled with the application of the RMP rotating field, whilst maintaining the H mode. During mitigation, the ELM peak heat flux is seen to be reduced by 50% for a halving in the ELM energy and motion of the strike point, consistent with the rotation of the applied RMP field, is seen using high spatial resolution (1.5mm at the target) heat flux profiles measured using infrared (IR) thermography. △ Less

Submitted 9 October, 2014; originally announced October 2014.

Comments: 18 pages, 6 figures

Journal ref: Journal of Nuclear Materials, Vol.463, August 2015, pp.723-726

Pellet fuelling with edge-localised modes controlled by external magnetic perturbations in MAST

Authors: M Valovic, L Garzotti, C Gurl, A Kirk, D Dunai, A R Field, I Lupelli, G Naylor, A Thornton

Abstract: The fuelling of plasmas by shallow frozen pellets with simultaneous mitigation of edge localised modes (ELM) by external magnetic perturbation is demonstrated on the MAST tokamak. Post-pellet particle loss is dominated by ELMs and inter-ELM gas fuelling. It is shown that the size of post-pellet ELMs can be controlled by external magnetic perturbations. Post-pellet ELMs remove particles from the la… ▽ More The fuelling of plasmas by shallow frozen pellets with simultaneous mitigation of edge localised modes (ELM) by external magnetic perturbation is demonstrated on the MAST tokamak. Post-pellet particle loss is dominated by ELMs and inter-ELM gas fuelling. It is shown that the size of post-pellet ELMs can be controlled by external magnetic perturbations. Post-pellet ELMs remove particles from the large part of pellet deposition zone including the area with positive density gradient. The mechanism explaining this peculiarity of particle loss is suggested. △ Less

Submitted 2 July, 2014; originally announced July 2014.

Comments: 7 pages, 4 figures. This is an author-created, un-copyedited version of an article submitted for publication in Nuclear Fusion. IOP Publishing Ltd and IAEA are not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: Nuclear Fusion, Vol.55, No.1, January 2015, pp.013011

Scaling of the scrape-off layer width during inter-ELM H modes on MAST as measured by infrared thermography

Authors: A. J. Thornton, A. Kirk, MAST Team

Abstract: The power load to the divertor surfaces is a key concern for future devices such as ITER, due to the thermal limits on the material surface. One factor that characterizes the heat flux to the divertor is the fall off length in the scrape-off layer (SOL), which recent empirical scalings have shown could be as small as 1 mm. These predictions are based on a multi-machine scaling of the heat flux wid… ▽ More The power load to the divertor surfaces is a key concern for future devices such as ITER, due to the thermal limits on the material surface. One factor that characterizes the heat flux to the divertor is the fall off length in the scrape-off layer (SOL), which recent empirical scalings have shown could be as small as 1 mm. These predictions are based on a multi-machine scaling of the heat flux width fitted using an expression for the divertor heat flux profile which includes a term for the exponential decay in the SOL and diffusion about the last closed flux surface (LCFS) in the private flux region. △ Less

Submitted 11 June, 2014; originally announced June 2014.

Comments: 20 pages, 16 figures

Journal ref: Plasma Physics and Controlled Fusion, Vol.56, No.5, May 2014, p.055008

Measurement, correction and implications of the intrinsic error fields on MAST

Authors: A. Kirk, Yueqiang Liu, R. Martin, G. Cunningham, D. Howell, the MAST team

Abstract: The misalignment of field coils in tokamaks can lead to toroidal asymmetries in the magnetic field, which are known as intrinsic error fields. These error fields often lead to the formation of locked modes in the plasma, which limit the lowest density that is achievable. The intrinsic error fields on MAST have been determined by the direct measurement of the toroidal asymmetry of the fields from t… ▽ More The misalignment of field coils in tokamaks can lead to toroidal asymmetries in the magnetic field, which are known as intrinsic error fields. These error fields often lead to the formation of locked modes in the plasma, which limit the lowest density that is achievable. The intrinsic error fields on MAST have been determined by the direct measurement of the toroidal asymmetry of the fields from these coils and have been parameterised in terms of distortions to the coils. The error fields are corrected using error field correction coils, where the optimum correction is found by determining the current required to ensure that the discharge is furthest from the onset of a locked mode. These empirically derived corrections have been compared with the known coil distortions. In the vacuum approximation there is a factor of ~ 3 difference between the predicted and empirically determined correction. When the plasma response is included better agreement is obtained, but there are still some cases where the agreement is not good, which suggests that other effects such as the non-linear coupling of the error field to the plasma are important. △ Less

Submitted 23 December, 2013; originally announced December 2013.

Comments: 42 pages, 19 figures

Journal ref: Plasma Physics and Controlled Fusion, Vol.56, No.10, October 2014, pp.104003

Current understanding of the processes underlying the triggering of and energy loss associated with type I ELMs

Authors: A. Kirk, D. Dunai, M. Dunne, G. Huijsmans, S. Pamela, M. Becoulet, J. R. Harrison, J. Hillesheim, C. Roach, S. Saarelma

Abstract: The type I ELMy H-mode is the baseline operating scenario for ITER. While it is known that the type I ELM ultimately results from the peeling-ballooning instability, there is growing experimental evidence that a mode grows up before the ELM crash that may modify the edge plasma, which then leads to the ELM event due to the peeling-ballooning mode. The triggered mode results in the release of a lar… ▽ More The type I ELMy H-mode is the baseline operating scenario for ITER. While it is known that the type I ELM ultimately results from the peeling-ballooning instability, there is growing experimental evidence that a mode grows up before the ELM crash that may modify the edge plasma, which then leads to the ELM event due to the peeling-ballooning mode. The triggered mode results in the release of a large number of particles and energy from the core plasma but the precise mechanism by which these losses occur is still not fully understood and hence makes predictions for future devices uncertain. Our current understanding of the processes that trigger type I ELMs and the size of the resultant energy loss are reviewed and compared to experimental data and ideas for further development are discussed. △ Less

Submitted 16 December, 2013; originally announced December 2013.

Comments: 35 pages, 9 figures

Journal ref: Nuclear Fusion, Vol.54, No.11, November 2014, pp.114012

Modelling of three dimensional equilibrium and stability of MAST plasmas with magnetic perturbations using VMEC and COBRA

Authors: C J Ham, I T Chapman, A Kirk, S Saarelma

Abstract: It is known that magnetic perturbations can mitigate edge localized modes (ELMs) in experiments, for example MAST (Kirk et al 2013 Nucl. Fusion 53 043007). One hypothesis is that the magnetic perturbations cause a three dimensional corrugation of the plasma and this corrugated plasma has different stability properties to peeling-ballooning modes compared to an axisymmetric plasma. It has been show… ▽ More It is known that magnetic perturbations can mitigate edge localized modes (ELMs) in experiments, for example MAST (Kirk et al 2013 Nucl. Fusion 53 043007). One hypothesis is that the magnetic perturbations cause a three dimensional corrugation of the plasma and this corrugated plasma has different stability properties to peeling-ballooning modes compared to an axisymmetric plasma. It has been shown in an up-down symmetric plasma that magnetic perturbations in tokamaks will break the usual axisymmetry of the plasma causing three dimensional displacements (Chapman et al 2012 Plasma Phys. Control. Fusion 54 105013). We produce a free boundary three-dimensional equilibrium of a lower single null MAST relevant plasma using VMEC (S P Hirshman and J C Whitson 1983 Phys. Fluids 26 3553). The current and pressure profiles used for the modelling are similar to those deduced from axisymmetric analysis of experimental data with ELMs. We focus on the effect of applying $n=3$ and $n=6$ magnetic perturbations using the RMP coils. A midplane displacement of over $\pm 1$ cm is seen when the full current is applied. The current in the coils is scaned and a linear relationship between coil current and midplane displacement is found. The effect of this non-axisymmetric equilibrium on infinite $n$ ballooning stability is investigated using COBRA (R Sanchez et al 2000 J. Comput. Phys. 161 576-588). △ Less

Submitted 11 December, 2013; originally announced December 2013.

Comments: 13 pages, 10 figures

Journal ref: Physics of Plasmas, Vol.21, No.10, October 2014, pp.102501

The effect of resonant magnetic perturbations on the divertor heat and particle fluxes in MAST

Authors: A. J. Thornton, A. Kirk, P. Cahyna, I. T. Chapman, J. R. Harrison, Yueqiang Liu, MAST Team

Abstract: Edge localised modes (ELMs) are a concern for future devices, such as ITER, due to the large transient heat loads they generate on the divertor surfaces which could limit the operational time of the device. This paper discusses the application of resonant magnetic perturbations (RMPs) as a mechanism for ELM control on MAST. Experiments have been performed using an n=3 toroidal mode number perturba… ▽ More Edge localised modes (ELMs) are a concern for future devices, such as ITER, due to the large transient heat loads they generate on the divertor surfaces which could limit the operational time of the device. This paper discusses the application of resonant magnetic perturbations (RMPs) as a mechanism for ELM control on MAST. Experiments have been performed using an n=3 toroidal mode number perturbation and measurements of the strike point splitting performed. The measurements have been made using both infrared and visible imaging to measure the heat and particle flux to the divertor. The measured profiles have shown clear splitting in L-mode which compares well with the predication of the splitting location from modelling including the effect of screening. The splitting of the strike point has also been studied as a function of time during the ELM. The splitting varies during the ELM, being the strongest at the time of the peak heat flux and becoming more filamentary at the end of the ELM (200 microseconds after the peak midplane D(alpha) emission). Variation in the splitting profiles has also been seen, with some ELMs showing clear splitting and others no splitting. A possible explanation of this effect is proposed, and supported by modelling, which concerns the relative phase between the RMP field and the ELM filament location. △ Less

Submitted 11 June, 2014; v1 submitted 9 July, 2013; originally announced July 2013.

Comments: 26 pages, 26 figures. Presented at the Stochasticity in Fusion Plasmas Workshop, Aachen, March 2013

Journal ref: Nucl. Fusion 54 (2014) 064011

Characteristics of X-point Lobe Structures in Single-Null Discharges on MAST

Authors: J. R. Harrison, A. Kirk, I. T. Chapman, P. Cahyna, Yueqiang Liu, E. Nardon, A. J. Thornton

Abstract: Lobe structures due to the application of resonant magnetic perturbations (RMPs) have been observed using wide-angle imaging of light from He1+ ions in the vicinity of the lower X-point in MAST. The data presented are from lower single-null discharges where RMPs of toroidal mode number, n, of 4 and 6 were applied. It has been found that, above a threshold value, the lobe structures extend radially… ▽ More Lobe structures due to the application of resonant magnetic perturbations (RMPs) have been observed using wide-angle imaging of light from He1+ ions in the vicinity of the lower X-point in MAST. The data presented are from lower single-null discharges where RMPs of toroidal mode number, n, of 4 and 6 were applied. It has been found that, above a threshold value, the lobe structures extend radially, linearly with the coil current, both in L-mode and H-mode. It is observed that after the application of the RMP, as the toroidal rotation in the confined plasma decreases, the lobes extend radially, suggesting the plasma is less effectively screening the RMP field. Comparing the imaging data with results from vacuum modelling shows that this technique can accurately predict the number and poloidal location of the lobes, but over-estimates their radial extent. More accurate estimates of the extent of the lobes can be made by accounting for plasma screening of the RMP field. Qualitative agreement between simulation and experiment is found if it is assumed that the RMP penetrates 2% in normalised radius from the last closed flux surface. △ Less

Submitted 5 July, 2013; originally announced July 2013.

Comments: 32 pages, 20 figures

Journal ref: Nuclear Fusion, Vol.54, No.6, June 2014, p.064015

Scrape-off layer ion temperature measurements at the divertor target in MAST by retarding field energy analyser

Authors: S. Elmore, S. Y. Allan, A. Kirk, A. J. Thornton, J. R. Harrison, P. Tamain, M. Kocan, J. W. Bradley, MAST Team

Abstract: Knowledge of the ion temperature (Ti) is of key importance for determining heat fluxes to the divertor and plasma facing components, however data regarding this is limited compared to electron temperature (Te) data. Ti measurements at the divertor target, between edge-localised modes (inter-ELM) H-mode, have been made using a novel retarding field energy analyser (RFEA). Knowledge of the ion temperature (Ti) is of key importance for determining heat fluxes to the divertor and plasma facing components, however data regarding this is limited compared to electron temperature (Te) data. Ti measurements at the divertor target, between edge-localised modes (inter-ELM) H-mode, have been made using a novel retarding field energy analyser (RFEA). △ Less

Submitted 5 July, 2013; originally announced July 2013.

Comments: 17 pages, 6 figures

Journal ref: Journal of Nuclear Materials, Vol.438, Supplement, July 2013, p.S1212-S1215. Proceedings of the 20th International Conference on Plasma-Surface Interactions in Controlled Fusion Devices

Measurement and control of the fast ion redistribution on MAST

Authors: M. Turnyanskiy, C. D. Challis, R. J. Akers, M. Cecconello, D. L. Keeling, A. Kirk, R. Lake, S. D. Pinches, S. Sangaroon, I. Wodniak

Abstract: Previous experiments on MAST and other tokamaks have indicated that the level of fast ion redistribution can exceed that expected from classical diffusion and that this level increases with beam power. In this paper we present a quantification of this effect in MAST plasmas using a recently commissioned scanning neutron camera. The observed fast ion diffusivity correlates with the amplitude of n=1… ▽ More Previous experiments on MAST and other tokamaks have indicated that the level of fast ion redistribution can exceed that expected from classical diffusion and that this level increases with beam power. In this paper we present a quantification of this effect in MAST plasmas using a recently commissioned scanning neutron camera. The observed fast ion diffusivity correlates with the amplitude of n=1 energetic particle modes, indicating that they are the probable cause of the non-classical fast ion diffusion in MAST. Finally, it will be shown that broadening the fast ion pressure profile by the application of neutral beam injection at an off-axis location can mitigate the growth of these modes and result in the classical fast ion behaviour △ Less

Submitted 1 July, 2013; originally announced July 2013.

Comments: 23 pages, 13 figures

Journal ref: Nuclear Fusion, Vol.53, No.5, May 2013, p.053016

Understanding the effect resonant magnetic perturbations have on ELMs

Authors: A. Kirk, I. T. Chapman, T. E. Evans, C. Ham, J. R. Harrison, G. Huijsmans, Y. Liang, Y. Q. Liu, A. Loarte, W. Suttrop, A. J. Thornton

Abstract: All current estimations of the energy released by type I ELMs indicate that, in order to ensure an adequate lifetime of the divertor targets on ITER, a mechanism is required to decrease the amount of energy released by an ELM, or to eliminate ELMs altogether. One such amelioration mechanism relies on perturbing the magnetic field in the edge plasma region, either leading to more frequent, smaller… ▽ More All current estimations of the energy released by type I ELMs indicate that, in order to ensure an adequate lifetime of the divertor targets on ITER, a mechanism is required to decrease the amount of energy released by an ELM, or to eliminate ELMs altogether. One such amelioration mechanism relies on perturbing the magnetic field in the edge plasma region, either leading to more frequent, smaller ELMs (ELM mitigation) or ELM suppression. This technique of Resonant Magnetic Perturbations (RMPs) has been employed to suppress type I ELMs at high collisionality/density on DIII-D, ASDEX Upgrade, KSTAR and JET and at low collisionality on DIII-D. At ITER-like collisionality the RMPs enhance the transport of particles or energy and keep the edge pressure gradient below the 2D linear ideal MHD critical value that would trigger an ELM, whereas at high collisionality/density the type I ELMs are replaced by small type II ELMs. Although ELM suppression only occurs within limitied operational ranges, ELM mitigation is much more easily achieved. The exact parameters that determine the onset of ELM suppression are unknown but in all cases the magnetic perturbations produce 3D distortions to the plasma and enhanced particle transport. The incorporation of these 3D effects in codes will be essential in order to make quantitative predictions for future devices. △ Less

Submitted 28 June, 2013; originally announced June 2013.

Comments: 32 pages, 9 figures

Journal ref: Plasma Physics & Controlled Fusion, Vol.55, December 2013, p.124003

L-Mode and Inter-ELM Divertor Particle and Heat Flux Width Scaling on MAST

Authors: J. R. Harrison, G. M. Fishpool, A. Kirk

Abstract: The distribution of particles and power to plasma-facing components is of key importance in the design of next-generation fusion devices. Power and particle decay lengths have been measured in a number of MAST L-mode and H-mode discharges in order to determine their parametric dependencies, by fitting power and particle flux profiles measured by divertor Langmuir probes, to a convolution of an exp… ▽ More The distribution of particles and power to plasma-facing components is of key importance in the design of next-generation fusion devices. Power and particle decay lengths have been measured in a number of MAST L-mode and H-mode discharges in order to determine their parametric dependencies, by fitting power and particle flux profiles measured by divertor Langmuir probes, to a convolution of an exponential decay and a Gaussian function. In all discharges analysed, it is found that exponential decay lengths mapped to the midplane are mostly dependent on separatrix electron density and plasma current (or parallel connection length). The widths of the convolved Gaussian functions have been used to derive an approximate diffusion coefficient, which is found to vary from 1m2/s to 7m2/s, and is systematically lower in H-mode compared with L-mode. △ Less

Submitted 28 June, 2013; originally announced June 2013.

Comments: 17 pages, 5 figures

Journal ref: Journal of Nuclear Materials, Vol.438, Supplement, July 2013, p.S375-S378. Proceedings of the 20th International Conference on Plasma-Surface Interactions in Controlled Fusion Devices

MAST-Upgrade Divertor Facility and Assessing Performance of Long-Legged Divertors

Authors: G. Fishpool, J. Canik, G. Cunningham, J. Harrison, I. Katramados, A. Kirk, M. Kovari, H. Meyer, R. Scannell, the MAST-Upgrade Team

Abstract: A potentially important feature in a divertor design for a high-power tokamak is an extended and expanded divertor leg. The upgrade to MAST will allow a wide range of such divertor leg geometries to be produced, and hence will allow the roles of greatly increased connection length and flux expansion to be experimentally tested. This will include testing the potential of the Super-X configuration [… ▽ More A potentially important feature in a divertor design for a high-power tokamak is an extended and expanded divertor leg. The upgrade to MAST will allow a wide range of such divertor leg geometries to be produced, and hence will allow the roles of greatly increased connection length and flux expansion to be experimentally tested. This will include testing the potential of the Super-X configuration [1]. The design process for the upgrade has required analysis of producing and controlling the magnetic configurations, and has included consideration of the roles that divertor closure and increasing magnetic connection length will play. △ Less

Submitted 28 June, 2013; originally announced June 2013.

Comments: 16 pages, 5 figures

Journal ref: Journal of Nuclear Materials, Vol.438, Supplement, July 2013, p.S356-S359. Proceedings of the 20th International Conference on Plasma-Surface Interactions in Controlled Fusion Devices

Ion energy measurements on MAST using a midplane RFEA

Authors: S. Y. Allan, S. Elmore, A. Kirk, M. Kočan, P. Tamain

Abstract: Ion energy measurements have been made in the scrape off layer of the Mega Amp Spherical Tokamak (MAST) using a midplane retarding field energy analyser (RFEA) in H-mode plasmas during the inter-edge localised mode (ELM) period and during type I and type III ELMs. During the inter-ELM period at distances of 3 to 8 cm from the last closed flux surface (LCFS), ion temperatures of 20 to 70 eV have be… ▽ More Ion energy measurements have been made in the scrape off layer of the Mega Amp Spherical Tokamak (MAST) using a midplane retarding field energy analyser (RFEA) in H-mode plasmas during the inter-edge localised mode (ELM) period and during type I and type III ELMs. During the inter-ELM period at distances of 3 to 8 cm from the last closed flux surface (LCFS), ion temperatures of 20 to 70 eV have been measured giving an ion to electron temperature ratio of 2 to 7 with a mean of 4. During type III ELMs, an ion temperature of 50 eV has been measured 3 to 6 cm from the LCFS which decreases to 30 eV at distances 11 to 16 cm from the LCFS. During type I ELMs, an ion temperature of 40 eV has been measured at a distance of 10 to 15 cm from the LCFS. △ Less

Submitted 27 June, 2013; originally announced June 2013.

Comments: 15 pages, 5 figures

Journal ref: Journal of Nuclear Materials, Vol.438, Supplement, July 2013, p.S1192-S1195. Proceedings of the 20th International Conference on Plasma-Surface Interactions in Controlled Fusion Devices

Divertor heat fluxes and profiles during mitigated and unmitigated Edge Localised Modes (ELMs) on the Mega Amp Spherical Tokamak (MAST)

Authors: A. J. Thornton, A. Kirk, I. T. Chapman, J. R. Harrison, the MAST Team

Abstract: Edge localised modes (ELMs) are a concern for future devices as they can limit the operational lifetime of the divertor. The mitigation of ELMs can be performed by the application of resonant magnetic perturbations (RMPs) which act to degrade the pressure gradient in the edge of the plasma. Investigations of the effect of RMPs on MAST have been performed in a range of plasmas using perturbations w… ▽ More Edge localised modes (ELMs) are a concern for future devices as they can limit the operational lifetime of the divertor. The mitigation of ELMs can be performed by the application of resonant magnetic perturbations (RMPs) which act to degrade the pressure gradient in the edge of the plasma. Investigations of the effect of RMPs on MAST have been performed in a range of plasmas using perturbations with toroidal mode numbers of n=3, 4 and 6. It has been seen that the RMPs increase the ELM frequency, which gives rise to a corresponding decrease in the ELM energy. The reduced ELM energy decreases the peak heat flux to the divertor, with a three fold reduction in the ELM energy, generating a 1.5 fold reduction in the peak heat flux. Measurements of the divertor heat flux profile show evidence of strike point splitting consistent with modelling using the vacuum code ERGOS. △ Less

Submitted 27 June, 2013; originally announced June 2013.

Comments: 13 pages, 7 figures

Journal ref: Journal of Nuclear Materials, Vol.438, Supplement, July 2013, p.S199-S202. Proceedings of the 20th International Conference on Plasma-Surface Interactions in Controlled Fusion Devices

Understanding ELM mitigation by resonant magnetic perturbations on MAST

Authors: A. Kirk, I. T. Chapman, Yueqiang Liu, P. Cahyna, P. Denner, G. Fishpool, C. J. Ham, J. R. Harrison, Yunfeng Liang, E. Nardon, S. Saarelma, R. Scannell, A. J. Thornton, the MAST team

Abstract: Sustained ELM mitigation has been achieved using RMPs with a toroidal mode number of n=4 and n=6 in lower single null and with n=3 in connected double null plasmas on MAST. The ELM frequency increases by up to a factor of eight with a similar reduction in ELM energy loss. A threshold current for ELM mitigation is observed above which the ELM frequency increases approximately linearly with current… ▽ More Sustained ELM mitigation has been achieved using RMPs with a toroidal mode number of n=4 and n=6 in lower single null and with n=3 in connected double null plasmas on MAST. The ELM frequency increases by up to a factor of eight with a similar reduction in ELM energy loss. A threshold current for ELM mitigation is observed above which the ELM frequency increases approximately linearly with current in the coils. A comparison of the filament structures observed during the ELMs in the natural and mitigated stages shows that the mitigated ELMs have the characteristics of type I ELMs even though their frequency is higher, their energy loss is reduced and the pedestal pressure gradient is decreased. During the ELM mitigated stage clear lobe structures are observed in visible-light imaging of the X-point region. The size of these lobes is correlated with the increase in ELM frequency observed. The RMPs produce a clear 3D distortion to the plasma and it is likely that these distortions explain why ELMs are destabilised and hence why ELM mitigation occurs. △ Less

Submitted 20 June, 2013; originally announced June 2013.

Comments: 41 pages, 19 figures. arXiv admin note: text overlap with arXiv:1305.3061

Journal ref: Nuclear Fusion, 53 043007 (2013)

Experimental and numerical characterisation of the turbulence in the Scrape-Off Layer of MAST

Authors: F. Militello, P. Tamain, W. Fundamenski, A. Kirk, V. Naulin, A. H. Nielsen, the MAST team

Abstract: Numerical simulations of interchange turbulence in the Scrape-Off Layer are performed in a regime relevant for a specific L-mode MAST (Mega Ampere Spherical Tokamak) discharge. Such a discharge was diagnosed with a reciprocating arm equipped with a Gundestrup probe. A detailed comparison of the average and statistical properties of the simulated and experimental ion saturation current is performed… ▽ More Numerical simulations of interchange turbulence in the Scrape-Off Layer are performed in a regime relevant for a specific L-mode MAST (Mega Ampere Spherical Tokamak) discharge. Such a discharge was diagnosed with a reciprocating arm equipped with a Gundestrup probe. A detailed comparison of the average and statistical properties of the simulated and experimental ion saturation current is performed. Good agreement is found in the time averaged radial profile, in the probability distribution functions (PDFs) and in qualitative features of the signals such as the shape, duration and separation of burst events. These results confirm the validity of the simple interchange model used and help to identify where it can be improved. Finally, the simulated data are used to assess the importance of the temperature fluctuations on plasma potential and radial velocity measurements acquired with Langmuir probes. It is shown that the correlation between the actual plasma quantities and the signal of the synthetic diagnostics is poor, suggesting that accurate measurements of the temperature fluctuations are needed in order to obtain reliable estimates of the perpendicular fluxes. △ Less

Submitted 22 May, 2013; originally announced May 2013.

Comments: 23 pages, 16 figures. This is an author-created, un-copyedited version of an article accepted for publication in Plasma Physics and Controlled Fusion. IOP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: Plasma Physics and Controlled Fusion, Vol.55, No.2. February 2013, pp. 025005

Toroidal modeling of penetration of the resonant magnetic perturbation field

Authors: Yueqiang Liu, A. Kirk, Y. Sun

Abstract: A toroidal, quasi-linear model is proposed to study the penetration dynamics of the resonant magnetic perturbation (RMP) field into the plasma. The model couples the linear, fluid plasma response to a toroidal momentum balance equation, which includes torques induced by both fluid electromagnetic force and by (kinetic) neoclassical toroidal viscous force. The numerical results for a test toroidal… ▽ More A toroidal, quasi-linear model is proposed to study the penetration dynamics of the resonant magnetic perturbation (RMP) field into the plasma. The model couples the linear, fluid plasma response to a toroidal momentum balance equation, which includes torques induced by both fluid electromagnetic force and by (kinetic) neoclassical toroidal viscous force. The numerical results for a test toroidal equilibrium quantify the effects of various physical parameters on the field penetration and on the plasma rotation braking. The neoclassical toroidal viscous torque plays a dominant role in certain region of the plasma, for the RMP penetration problem considered in this work. △ Less

Submitted 16 May, 2013; originally announced May 2013.

Comments: 20 pages, 14 figures. Copyright 2013 United Kingdom Atomic Energy Authority. This article may be downloaded for personal use only. Any other use requires prior permission of the author and the American Institute of Physics

Journal ref: Phys. Plasmas 20, 042503 (2013)

Towards understanding edge localised mode mitigation by resonant magnetic perturbations in MAST

Authors: I. T. Chapman, A. Kirk, C. J. Ham, J. R. Harrison, Y. Q. Liu, S. Saarelma, R. Scannell, A. J. Thornton, M. Becoulet, F. Orain, W. A. Cooper, S. Pamela, MAST Team

Abstract: Type-I Edge Localised Modes (ELMs) have been mitigated in MAST through the application of n = 3, 4 and 6 resonant magnetic perturbations (RMPs). For each toroidal mode number of the non-axisymmetric applied fields, the frequency of the ELMs has been increased significantly, and the peak heat flux on the divertor plates reduced commensurately. This increase in ELM frequency occurs despite a signifi… ▽ More Type-I Edge Localised Modes (ELMs) have been mitigated in MAST through the application of n = 3, 4 and 6 resonant magnetic perturbations (RMPs). For each toroidal mode number of the non-axisymmetric applied fields, the frequency of the ELMs has been increased significantly, and the peak heat flux on the divertor plates reduced commensurately. This increase in ELM frequency occurs despite a significant drop in the edge pressure gradient, which would be expected to stabilise the peeling-ballooning modes thought to be responsible for type-I ELMs. Various mechanisms which could cause a destabilisation of the peeling-ballooning modes are presented, including pedestal widening, plasma rotation braking, three dimensional corrugation of the plasma boundary and the existence of radially extended lobe structures near to the X-point. This leads to a model aimed at resolving the apparent dichotomy of ELM control, that is to say ELM suppression occurring due to the pedestal pressure reduction below the peeling-ballooning stability boundary, whilst the reduction in pressure can also lead to ELM mitigation, which is ostensibly a destabilisation of peeling-ballooning modes. In the case of ELM mitigation, the pedestal broadening, 3d corrugation or lobes near the X-point degrade ballooning stability so much that the pedestal recovers rapidly to cross the new stability boundary at lower pressure more frequently, whilst in the case of suppression, the plasma parameters are such that the particle transport reduces the edge pressure below the stability boundary which is only mildly affected by negligible rotation braking, small edge corrugation or short, broad lobe structures. △ Less

Submitted 16 May, 2013; originally announced May 2013.

Comments: 23 pages, 12 figures. Copyright (2013) United Kingdom Atomic Energy Authority. This article may be downloaded for personal use only. Any other use requires prior permission of the author and the American Institute of Physics

Journal ref: Phys. Plasmas 20, 056101 (2013)

Effect of resonant magnetic perturbations with toroidal mode numbers of 4 and 6 on ELMs in single null H-mode plasmas in MAST

Authors: A. Kirk, I. T. Chapman, J. Harrison, Yueqiang Liu, E. Nardon, S. Saarelma, R. Scannell, A. J. Thornton, the MAST team

Abstract: The application of resonant magnetic perturbations (RMPs) with a toroidal mode number of n=4 or n=6 to lower single null plasmas in the MAST tokamak produces up to a factor of 5 increase in Edge Localized Mode (ELM) frequency and reduction in plasma energy loss associated with type-I ELMs. A threshold current for ELM mitigation is observed above which the ELM frequency increases approximately line… ▽ More The application of resonant magnetic perturbations (RMPs) with a toroidal mode number of n=4 or n=6 to lower single null plasmas in the MAST tokamak produces up to a factor of 5 increase in Edge Localized Mode (ELM) frequency and reduction in plasma energy loss associated with type-I ELMs. A threshold current for ELM mitigation is observed above which the ELM frequency increases approximately linearly with current in the coils. Despite a large scan of parameters, complete ELM suppression has not been achieved. The results have been compared to modelling performed using either the vacuum approximation or including the plasma response. During the ELM mitigated stage clear lobe structures are observed in visible-light imaging of the X-point region. The size of these lobes is correlated with the increase in ELM frequency observed. The characteristics of the mitigated ELMs are similar to those of the natural ELMs suggesting that they are type I ELMs which are triggered at a lower pressure gradient. The application of the RMPs in the n=4 and n=6 configurations before the L-H transition has little effect on the power required to achieve H-mode while still allowing the first ELM to be mitigated. △ Less

Submitted 14 May, 2013; originally announced May 2013.

Comments: 48 pages, 23 figures. This is an author-created, un-copyedited version of an article accepted for publication in Plasma Phys. Control. Fusion. IOP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: Plasma Phys. Control. Fusion 55 015006 (2013)

Pellet fuelling of plasmas with ELM mitigation by resonant magnetic perturbations in MAST

Authors: M Valovic, G Cunningham, L Garzotti, C Gurl, A Kirk, G Naylor, A Patel, R Scannell, A J Thornton

Abstract: Shallow fuelling pellets are injected from the high field side into plasmas in which ELMs have been mitigated using external magnetic perturbation coils. The data are compared with ideal assumptions in the ITER fuelling model, namely that mitigated ELMs are not affected by fuelling pellets. Firstly it is shown that during the pellet evaporation an ELM is triggered, during which the amount particle… ▽ More Shallow fuelling pellets are injected from the high field side into plasmas in which ELMs have been mitigated using external magnetic perturbation coils. The data are compared with ideal assumptions in the ITER fuelling model, namely that mitigated ELMs are not affected by fuelling pellets. Firstly it is shown that during the pellet evaporation an ELM is triggered, during which the amount particle loss could be larger (factor ~1.5) than the particle loss during an ELM which was not induced by pellet. Secondly, a favourable example is shown in which post-pellet particle losses due to mitigated ELMs are similar to the non-pellet case, however unfavourable counter-examples also exist. △ Less

Submitted 13 May, 2013; originally announced May 2013.

Comments: 9 pages, 6 figures. This is an author-created, un-copyedited version of an article accepted for publication in Plasma Physics and Controlled Fusion. IOP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: Plasma Phys. Control. Fusion 55 025009 (2013)

Inter-ELM pedestal evolution on MAST and impact of Resonant Magnetic Perturbations

Authors: R. Scannell, A. Kirk, I. T. Chapman

Abstract: The peak pressure gradient in the pedestal (dPe/dψ) on MAST varies little between edge localized modes (ELMs), although it varies between discharges due factors such as gas fuelling and plasma current. The pressure pedestal width in flux space on the high-field side (HFS), both during the inter-ELM period and amongst different plasma discharges is consistent with a scaling of . In flux space very… ▽ More The peak pressure gradient in the pedestal (dPe/dψ) on MAST varies little between edge localized modes (ELMs), although it varies between discharges due factors such as gas fuelling and plasma current. The pressure pedestal width in flux space on the high-field side (HFS), both during the inter-ELM period and amongst different plasma discharges is consistent with a scaling of . In flux space very similar dPe/dψ and Δpe are observed on the HFS and low-field side (LFS) in single null configuration. This symmetry is broken by the application of resonant magnetic perturbations (RMPs). During ELM mitigation by application of RMPs changes in the edge transport barrier position and width are observed. These changes are dependent on the intensity of the RMP and on the toroidal location with respect to the RMP phase. An outward displacement of up to 30 mm and increase in the edge pedestal width of up to 50% with respect to the coils case off are observed. Increased particle transport causes a decrease in ne,ped, and hence Pe,ped, as is observed on other devices. The combination of an increase in Δpe on the LFS and decrease in Pe,ped results in significantly reduced LFS dPe/dψ when these perturbations are applied to the plasma edge. A decrease in dPe/dψ on the HFS is also observed due to RMP; however, this decrease is caused solely by the Pe,ped decrease whilst no expansion of Δpe on the HFS is observed. △ Less

Submitted 13 May, 2013; originally announced May 2013.

Comments: 26 pages, 11 figures. This is an author-created, un-copyedited version of an article accepted for publication in Plasma Physics and Controlled Fusion. IOP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it

Journal ref: Plasma Phys. Control. Fusion 55 035013 (2013)

Effect of resonant magnetic perturbations on ELMs in connected double null plasmas in MAST

Authors: A. Kirk, Yueqiang Liu, I. T. Chapman, J. Harrison, E. Nardon, R. Scannell, A. J. Thornton, the MAST team

Abstract: The application of resonant magnetic perturbations (RMPs) with a toroidal mode number of n=3 to connected double null plasmas in the MAST tokamak produces up to a factor of 9 increase in Edge Localized Mode (ELM) frequency and reduction in plasma energy loss associated with type-I ELMs. A threshold current for ELM mitigation is observed above which the ELM frequency increases approximately linearl… ▽ More The application of resonant magnetic perturbations (RMPs) with a toroidal mode number of n=3 to connected double null plasmas in the MAST tokamak produces up to a factor of 9 increase in Edge Localized Mode (ELM) frequency and reduction in plasma energy loss associated with type-I ELMs. A threshold current for ELM mitigation is observed above which the ELM frequency increases approximately linearly with current in the coils. The effect of the RMPs is found to be scenario dependent. In one scenario the mitigation is only due to a large density pump out event and if the density is recovered by gas puffing a return to type I ELMs is observed. In another scenario sustained ELM mitigation can be achieved irrespective of the amount of fuelling. Despite a large scan of parameters complete ELM suppression has not been achieved. The results have been compared to modelling performed using either the vacuum approximation or including the plasma response. The requirement for a resonant condition, that is an optimum alignment of the perturbation with the plasma, has been confirmed by performing a scan in the pitch angle of the applied field. △ Less

Submitted 1 March, 2013; originally announced March 2013.

Comments: 39 pages,19 figures

Journal ref: Plasma Physics & Controlled Fusion, Vol.55, Jan. 2013, p.045007

Microtearing modes at the top of the pedestal

Authors: D. Dickinson, C. M. Roach, S. Saarelma, R. Scannell, A. Kirk, H. R. Wilson

Abstract: Microtearing modes (MTMs) are unstable in the shallow gradient region just inside the top of the pedestal in the spherical tokamak experiment MAST, and may play an important role in the pedestal evolution. The linear properties of these instabilities are compared with MTMs deeper inside the core, and further detailed investigations expose the basic drive mechanism. MTMs near the MAST pedestal top… ▽ More Microtearing modes (MTMs) are unstable in the shallow gradient region just inside the top of the pedestal in the spherical tokamak experiment MAST, and may play an important role in the pedestal evolution. The linear properties of these instabilities are compared with MTMs deeper inside the core, and further detailed investigations expose the basic drive mechanism. MTMs near the MAST pedestal top are not well described by existing theories. In particular the growth rate of the dominant edge MTM does not peak at a finite collision frequency, as frequently reported for MTMs further into the core. Our study suggests that the edge MTM is driven by a collisionless trapped particle mechanism that is sensitive to magnetic drifts. This drive is enhanced in the outer region of MAST by a high magnetic shear and a high trapped particle fraction. Observations of similar modes on conventional aspect ratio devices suggests this drive mechanism may be somewhat ubiquitous towards the edge of current day and future hot tokamaks. △ Less

Submitted 9 January, 2013; v1 submitted 17 September, 2012; originally announced September 2012.

Comments: 14 pages, 10 figures (21 unique graphics)

Strike point splitting induced by the application of magnetic perturbations on MAST

Authors: P. Cahyna, M. Peterka, A. Kirk, A. Thornton, J. Harrison, D. Muir, R. Panek, the MAST team

Abstract: Divertor strike point splitting induced by resonant magnetic perturbations (RMPs) has been observed on MAST for a variety of RMP configurations in a plasma scenario with Ip=750kA where those configurations all have similar resonant components. Complementary measurements have been obtained with divertor Langmuir probes and an infrared camera. Clear splitting consistently appears in this scenario on… ▽ More Divertor strike point splitting induced by resonant magnetic perturbations (RMPs) has been observed on MAST for a variety of RMP configurations in a plasma scenario with Ip=750kA where those configurations all have similar resonant components. Complementary measurements have been obtained with divertor Langmuir probes and an infrared camera. Clear splitting consistently appears in this scenario only in the even configuration of the perturbation coils, similarly to the density pump-out. These results present a challenge for models of plasma response to RMPs. △ Less

Submitted 24 May, 2012; originally announced May 2012.

Comments: 9 pages, 4 figures, submitted to the proceedings of the 20th Conference on Plasma Surface Interactions, to be published in the Journal of Nuclear Materials

Journal ref: Journal of Nuclear Materials 438 (2013) S326-S329

Simultaneous measurement of quality factor and wavelength shift by phase shift microcavity ring down spectroscopy

Authors: M. Imran Cheema, Simin Mehrabani, Ahmad A. Hayat, Yves-Alain Peter, Andrea M. Armani, Andrew G. Kirk

Abstract: Optical resonant microcavities with ultra high quality factors are widely used for biosensing. Until now, the primary method of detection has been based upon tracking the resonant wavelength shift as a function of biodetection events. One of the sources of noise in all resonant-wavelength shift measurements is the noise due to intensity fluctuations of the laser source. An alternative approach is… ▽ More Optical resonant microcavities with ultra high quality factors are widely used for biosensing. Until now, the primary method of detection has been based upon tracking the resonant wavelength shift as a function of biodetection events. One of the sources of noise in all resonant-wavelength shift measurements is the noise due to intensity fluctuations of the laser source. An alternative approach is to track the change in the quality factor of the optical cavity by using phase shift cavity ring down spectroscopy, a technique which is insensitive to the intensity fluctuations of the laser source. Here, using biotinylated microtoroid resonant cavities, we show simultaneous measurement of the quality factor and the wavelength shift by using phase shift cavity ring down spectroscopy. These measurements were performed for disassociation phase of biotin-streptavidin reaction. We found that the disassociation curves are in good agreement with the previously published results. Hence, we demonstrate not only the application of phase shift cavity ring down spectroscopy to microcavities in the liquid phase but also simultaneous measurement of the quality factor and the wavelength shift for the microcavity biosensors in the application of kinetics measurements. △ Less

Submitted 27 March, 2012; v1 submitted 1 March, 2012; originally announced March 2012.

Observation of lobes near the X-point in resonant magnetic perturbation experiments on MAST

Authors: A. Kirk, J. Harrison, Yueqiang Liu, E. Nardon, I. T. Chapman, P. Denner, the MAST team

Abstract: The application of non-axisymmetric resonant magnetic perturbations (RMPs) with a toroidal mode number n=6 in the MAST tokamak produces a significant reduction in plasma energy loss associated with type-I Edge Localized Modes (ELMs), the first such observation with n>3. During the ELM mitigated stage clear lobe structures are observed in visible-light imaging of the X-point region. These lobes or… ▽ More The application of non-axisymmetric resonant magnetic perturbations (RMPs) with a toroidal mode number n=6 in the MAST tokamak produces a significant reduction in plasma energy loss associated with type-I Edge Localized Modes (ELMs), the first such observation with n>3. During the ELM mitigated stage clear lobe structures are observed in visible-light imaging of the X-point region. These lobes or manifold structures, that were predicted previously, have been observed for the first time in a range of discharges and their appearance is correlated with the effect of RMPs on the plasma i.e. they only appear above a threshold when a density pump out is observed or when the ELM frequency is increased. They appear to be correlated with the RMPs penetrating the plasma and may be important in explaining why the ELM frequency increases. The number and location of the structures observed can be well described using vacuum modelling. Differences in radial extent and poloidal width from vacuum modelling are likely to be due to a combination of transport effects and plasma screening. △ Less

Submitted 1 February, 2012; originally announced February 2012.

Comments: 15 pages, 5 figures

Journal ref: PRL 108, 255003 (2012)

Kinetic instabilities that limit β in the edge of a tokamak plasma: a picture of an H-mode pedestal

Authors: D. Dickinson, C. M. Roach, S. Saarelma, R. Scannell, A. Kirk, H. R. Wilson

Abstract: Plasma equilibria reconstructed from the Mega-Amp Spherical Tokamak (MAST) have sufficient resolution to capture plasma evolution during the short period between edge-localized modes (ELMs). Immediately after the ELM steep gradients in pressure, P, and density, ne, form pedestals close to the separatrix, and they then expand into the core. Local gyrokinetic analysis over the ELM cycle reveals the… ▽ More Plasma equilibria reconstructed from the Mega-Amp Spherical Tokamak (MAST) have sufficient resolution to capture plasma evolution during the short period between edge-localized modes (ELMs). Immediately after the ELM steep gradients in pressure, P, and density, ne, form pedestals close to the separatrix, and they then expand into the core. Local gyrokinetic analysis over the ELM cycle reveals the dominant microinstabilities at perpendicular wavelengths of the order of the ion Larmor radius. These are kinetic ballooning modes (KBMs) in the pedestal and microtearing modes (MTMs) in the core close to the pedestal top. The evolving growth rate spectra, supported by gyrokinetic analysis using artificial local equilibrium scans, suggest a new physical picture for the formation and arrest of this pedestal. △ Less

Submitted 14 May, 2012; v1 submitted 4 October, 2011; originally announced October 2011.

Comments: Final version as it appeared in PRL (March 2012). Minor improvements include: shortened abstract, and better colour table for figures. 4 pages, 6 figures

Towards the construction of a model to describe the inter-ELM evolution of the pedestal on MAST

Authors: D. Dickinson, S. Saarelma, R. Scannell, A. Kirk, C. M. Roach, H. R. Wilson

Abstract: Pedestal profiles that span the ELM cycle have been obtained and used to test the idea that the pedestal pressure gradient in MAST is limited by the onset of Kinetic Ballooning Modes (KBMs). During the inter-ELM period of a regularly type I ELM-ing discharge on MAST, the pressure pedestal height and width increase together while the pressure gradient increases by only 15 % during the ELM cycle. St… ▽ More Pedestal profiles that span the ELM cycle have been obtained and used to test the idea that the pedestal pressure gradient in MAST is limited by the onset of Kinetic Ballooning Modes (KBMs). During the inter-ELM period of a regularly type I ELM-ing discharge on MAST, the pressure pedestal height and width increase together while the pressure gradient increases by only 15 % during the ELM cycle. Stability analyses show that the pedestal region over which infinite-n ballooning modes are unstable also broadens during the ELM cycle. To test the relationship between the width of the region that is unstable to n = \infty ideal magnetohydrodynamic ballooning modes and KBMs the gyrokinetic code, GS2, has been used for microstability analysis of the edge plasma region in MAST. The gyrokinetic simulations find that KBM modes with twisting parity are the dominant microinstabilities in the steep pedestal region, with a transition to more slowly growing tearing parity modes in the shallower pressure gradient core region immediately inside the pedestal top. The region over which KBMs are unstable increases during the ELM cycle, and a good correlation is found between the regions unstable to KBMs and infinite-n ideal ballooning modes. △ Less

Submitted 30 September, 2011; v1 submitted 15 July, 2011; originally announced July 2011.

Comments: Version accepted and to appear in PPCF October 2011

Journal ref: Plasma Physics and Controlled Fusion 53 115010 (2011)

Accurate determination of the quality factor and tunneling distance of axisymmetric resonators for biosensing applications

Authors: M. Imran Cheema, Andrew G. Kirk

Abstract: Due to ultra high quality factor ($10^6-10^9$), axisymmetric optical microcavities are popular platforms for biosensing applications. It has been recently demonstrated that a microcavity biosensor can track a biodetection event as a function of its quality factor by using phase shift cavity ring down spectroscopy (PS-CRDS). However, to achieve maximum sensitivity, it is necessary to optimize the m… ▽ More Due to ultra high quality factor ($10^6-10^9$), axisymmetric optical microcavities are popular platforms for biosensing applications. It has been recently demonstrated that a microcavity biosensor can track a biodetection event as a function of its quality factor by using phase shift cavity ring down spectroscopy (PS-CRDS). However, to achieve maximum sensitivity, it is necessary to optimize the microcavity parameters for a given sensing application. Here, we introduce an improved finite element model which allows us to determine the optimized geometry for the PS-CRDS sensor. The improved model not only provides fast and accurate determination of quality factors but also determines the tunneling distance of axisymmetric resonators. The improved model is validated numerically, analytically, and experimentally. △ Less

Submitted 3 April, 2013; v1 submitted 10 January, 2011; originally announced January 2011.

Comments: Published in Optics Express, April 2, 2013

Journal ref: Optics Express, Vol. 21, Issue 7, pp. 8724-8735 (2013)