-
Towards a sub-kelvin cryogenic Fabry-Perot silicon cavity
Authors:
Joannès Barbarat,
Jonathan Gillot,
Jacques Millo,
Clément Lacroûte,
Thomas Legero,
Vincent Giordano,
Yann Kersalé
Abstract:
We report on the development of a sub-kelvin, single-crystal silicon Fabry-Perot cavity. Operating such a cavity below 1~K should reduce the thermal noise limit of the cavity, and by this way address the current limitations of ultrastable lasers. To further decrease mechanical losses, mirrors with silicon substrates and crystalline coatings are optically contacted to the spacer, resulting in a roo…
▽ More
We report on the development of a sub-kelvin, single-crystal silicon Fabry-Perot cavity. Operating such a cavity below 1~K should reduce the thermal noise limit of the cavity, and by this way address the current limitations of ultrastable lasers. To further decrease mechanical losses, mirrors with silicon substrates and crystalline coatings are optically contacted to the spacer, resulting in a room-temperature finesse of 220,000. To operate our cavity at sub-kelvin temperatures, we use a dilution refrigerator able to reach temperatures down to 10 mK. We have designed a mechanical mount to house our cavity in such a cryostat, with optimized heat transfer that will decrease the cooldown time for temperatures below 1~K. The estimated thermal noise is projected to be $\sim 7{\times}10^{-19}$ at 100~mK. However, silicon cavities with crystalline mirror coatings at cryogenic temperatures have shown birefringence correlated frequency fluctuations as well as unknown additional noise mechanisms \cite{yu2023, kedar2023}. We have measured a room-temperature TEM$_{00}$ birefringent mode splitting of about 250 kHz. Understanding and measuring these noise mechanisms will be a key to attaining fractional frequency stabilities beyond state-of-the-art.
△ Less
Submitted 12 June, 2024;
originally announced June 2024.
-
Heating rate measurement and characterization of a prototype surface-electrode trap for optical frequency metrology
Authors:
Thomas Lauprêtre,
Bachir Achi,
Lucas Groult,
Yann Kersalé,
Marion Delehaye,
Moustafa Abdel Hafiz,
Clément Lacroûte
Abstract:
We present the characterization of a prototype surface-electrode (SE) trap as a first step towards the realization of a compact, single-ion optical clock based on Yb$^+$. The use of a SE trap will be a key factor to benefit from clean-room fabrication techniques and technological advances made in the field of quantum information processing. We succesfully demonstrated trap** at a 500 $μ$m electr…
▽ More
We present the characterization of a prototype surface-electrode (SE) trap as a first step towards the realization of a compact, single-ion optical clock based on Yb$^+$. The use of a SE trap will be a key factor to benefit from clean-room fabrication techniques and technological advances made in the field of quantum information processing. We succesfully demonstrated trap** at a 500 $μ$m electrodes distance and characterized our trap in terms of lifetime and heating rate. This is to our knowledge the highest distance achieved for heating rates measurements in SE traps. This simple 5-wire design realized with simple materials yields a heating rate of $\mathbf{8\times 10^3}$ phonons/s. We provide an analysis of the performances of this prototype trap for optical frequency metrology.
△ Less
Submitted 16 June, 2022;
originally announced June 2022.
-
Residual amplitude modulation at the $10^{-7}$ level for ultra-stable lasers
Authors:
Jonathan Gillot,
Santerelli Falzon Tetsing-Talla,
Séverine Denis,
Gwenhaël Goavec-Merou,
Jacques Millo,
Clément Lacroûte,
Yann Kersalé
Abstract:
The stabilization of lasers on ultra-stable optical cavities by the Pound-Drever-Hall (PDH) technique is a widely used method. The PDH method relies on the phase-modulation of the laser, which is usually performed by an electro-optic modulator (EOM). When approaching the $10^{-16}$ level, this technology requires an active control of the residual amplitude modulation (RAM) generated by the EOM in…
▽ More
The stabilization of lasers on ultra-stable optical cavities by the Pound-Drever-Hall (PDH) technique is a widely used method. The PDH method relies on the phase-modulation of the laser, which is usually performed by an electro-optic modulator (EOM). When approaching the $10^{-16}$ level, this technology requires an active control of the residual amplitude modulation (RAM) generated by the EOM in order to bring the frequency stability of the laser down to the thermal noise limit of the ultra-stable cavity. In this article, we report on the development of an active system of RAM reduction based on a free space EOM, which is used to perform PDH-stabilization of a laser on a cryogenic silicon cavity. A RAM stability of $1.4 \times 10^{-7}$ is obtained by employing a digital servo that stabilizes the EOM DC electric field, the crystal temperature and the laser power. Considering an ultra-stable cavity with a finesse of $2.5\times 10^5$, this RAM level would contribute to the fractional frequency instability at the level of about $5\times 10^{-19}$, well below the state of the art thermal noise limit of a few $ 10^{-17}$.
△ Less
Submitted 7 June, 2022;
originally announced June 2022.
-
Digital Doppler-cancellation servo for ultra-stable optical frequency dissemination over fiber
Authors:
Shambo Mukherjee,
Jacques Millo,
Baptiste Marechal,
Séverine Denis,
Gwenhaël Goavec-Mérou,
Jean-Michel Friedt,
Yann Kersalé,
Clément Lacroûte
Abstract:
Progress made in optical references, including ultra-stable Fabry-Perot cavities, optical frequency combs and optical atomic clocks, have driven the need for ultra-stable optical fiber networks. Telecom-wavelength ultra-pure optical signal transport has been demonstrated on distances ranging from the laboratory scale to the continental scale. In this manuscript, we present a Doppler-cancellation s…
▽ More
Progress made in optical references, including ultra-stable Fabry-Perot cavities, optical frequency combs and optical atomic clocks, have driven the need for ultra-stable optical fiber networks. Telecom-wavelength ultra-pure optical signal transport has been demonstrated on distances ranging from the laboratory scale to the continental scale. In this manuscript, we present a Doppler-cancellation setup based on a digital phase-locked loop for ultra-stable optical signal dissemination over fiber. The optical phase stabilization setup is based on a usual heterodyne Michelson-interferometer setup, while the Software Defined Radio (SDR) implementation of the phase-locked loop is based on a compact commercial board embedding a field programmable gate array, analog-to-digital and digital-to-analog converters. Using three different configurations including an undersampling method, we demonstrate a 20 m long fiber link with residual fractional frequency instability as low as $10^{-18}$ at 1000 s, and an optical phase noise of $-70$ dBc/Hz at 1 Hz with a telecom frequency carrier.
△ Less
Submitted 9 November, 2021;
originally announced November 2021.
-
Ultra-compact reference ULE cavity
Authors:
Alexandre Didier,
Jacques Millo,
Baptiste Marechal,
Cyrus Rocher,
Enrico Rubiola,
Roméo Lecomte,
Morvan Ouisse,
Jérôme Delporte,
Clément Lacroûte,
Yann Kersalé
Abstract:
We present a first experimental characterization of our ultra-compact, ultra-stable laser. The heart of the apparatus is an original Fabry-Perot cavity with a 25 mm length and a pyramidal geometry, equipped with highly-reflective crystalline coatings. The cavity, along with its vacuum chamber and optical setup, fits inside a 30 L volume. We have measured the cavity thermal and vibration sensitivit…
▽ More
We present a first experimental characterization of our ultra-compact, ultra-stable laser. The heart of the apparatus is an original Fabry-Perot cavity with a 25 mm length and a pyramidal geometry, equipped with highly-reflective crystalline coatings. The cavity, along with its vacuum chamber and optical setup, fits inside a 30 L volume. We have measured the cavity thermal and vibration sensitivities, and present a first estimation of the cavity fractional frequency instability at $σ_y(1\rm{s})=7.5{\times}10^{-15}$.
△ Less
Submitted 17 December, 2019;
originally announced December 2019.
-
Absolute frequency measurements of the ${}^1{\rm S}_0 \rightarrow {}^1{\rm P}_1$ transition in ytterbium
Authors:
Thomas Lauprêtre,
Lucas Groult,
Bachir Achi,
Michael Petersen,
Yann Kersalé,
Marion Delehaye,
Clément Lacroûte
Abstract:
The ytterbium atom is widely used in the fields of atomic physics, cavity quantum electrodynamics, quantum information processing and optical frequency standards. There is however a strong dispersion among the reported values of the ${}^1{\rm S}_0 \rightarrow {}^1{\rm P}_1$ transition frequency. In this article, we present two independent measurements of the absolute frequency of this transition p…
▽ More
The ytterbium atom is widely used in the fields of atomic physics, cavity quantum electrodynamics, quantum information processing and optical frequency standards. There is however a strong dispersion among the reported values of the ${}^1{\rm S}_0 \rightarrow {}^1{\rm P}_1$ transition frequency. In this article, we present two independent measurements of the absolute frequency of this transition performed with two different wavemeters using atomic fluorescence spectroscopy. The cancellation of Doppler shifts is obtained by fine tuning the angle between the probe laser and the atomic beam. The resulting $^{174}\mathrm{Yb}$ isotope transition frequency is estimated to be $\,751\,526\,537\pm27$ MHz.
△ Less
Submitted 17 December, 2019;
originally announced December 2019.
-
Photonic Generation of High Power, Ultrastable Microwave Signals by Vernier Effect in a Femtosecond Laser Frequency Comb
Authors:
Khaldoun Saleh,
Jacques Millo,
Baptiste Marechal,
Benoît Dubois,
Ahmed Bakir,
Alexandre Didier,
Clément Lacroûte,
Yann Kersalé
Abstract:
Optical frequency division of an ultrastable laser to the microwave frequency range by an optical frequency comb has allowed the generation of microwave signals with unprecedently high spectral purity and stability. However, the generated microwave signal will suffer from a very low power level if no external optical frequency comb repetition rate multiplication device is used. This paper reports…
▽ More
Optical frequency division of an ultrastable laser to the microwave frequency range by an optical frequency comb has allowed the generation of microwave signals with unprecedently high spectral purity and stability. However, the generated microwave signal will suffer from a very low power level if no external optical frequency comb repetition rate multiplication device is used. This paper reports theoretical and experimental studies on the beneficial use of the Vernier effect together with the spectral selective filtering in a double directional coupler add-drop optical fibre ring resonator to increase the comb repetition rate and generate high power microwaves. The studies are focused on two selective filtering aspects: the high rejection of undesirable optical modes of the frequency comb and the transmission of the desirable modes with the lowest possible loss. Moreover, the conservation of the frequency comb stability and linewidth at the resonator output is particularly considered. Accordingly, a fibre ring resonator is designed, fabricated, and characterized, and a technique to stabilize the resonator's resonance comb is proposed. A significant power gain is achieved for the photonically generated beat note at 10 GHz. Routes to highly improve the performances of such proof-of-concept device are also discussed.
△ Less
Submitted 1 February, 2018;
originally announced February 2018.
-
Residual Phase Noise Measurement of Optical Second Harmonic Generation in PPLN Waveguides
Authors:
Marion Delehaye,
Jacques Millo,
Pierre-Yves Bourgeois,
Lucas Groult,
Rodolphe Boudot,
Enrico Rubiola,
Emmanuel Bigler,
Yann Kersalé,
Clément Lacroûte
Abstract:
We report on the characterization, including residual phase noise and fractional frequency instability, of fiber-coupled PPLN non-linear crystals. These components are devoted to frequency doubling 871 nm light from an extended-cavity diode laser to produce a 435.5 nm beam, corresponding to the ytterbium ion electric quadrupole clock transition. We measure doubling efficiencies of up to 117.5 %/W.…
▽ More
We report on the characterization, including residual phase noise and fractional frequency instability, of fiber-coupled PPLN non-linear crystals. These components are devoted to frequency doubling 871 nm light from an extended-cavity diode laser to produce a 435.5 nm beam, corresponding to the ytterbium ion electric quadrupole clock transition. We measure doubling efficiencies of up to 117.5 %/W. Using a Mach-Zehnder interferometer and an original noise rejection technique, the residual phase noise of the doublers is estimated to be lower than ${\rm -35\, dBrad^2/Hz}$ at 1 Hz, making these modules compatible with up-to-date optical clocks and ultra-stable cavities. The influence of external parameters such as pump laser frequency and intensity is investigated, showing that they do not limit the stability of the frequency-doubled signal. Our results demonstrate that such compact, fiber-coupled modules are suitable for use in ultra-low phase noise metrological experiments, including transportable optical atomic clocks.
△ Less
Submitted 11 July, 2017;
originally announced July 2017.
-
Compact Yb$^+$ optical atomic clock project: design principle and current status
Authors:
Clément Lacroûte,
Maël Souidi,
Pierre-Yves Bourgeois,
Jacques Millo,
Khaldoun Saleh,
Emmanuel Bigler,
Rodolphe Boudot,
Vincent Giordano,
Yann Kersalé
Abstract:
We present the design of a compact optical clock based on the $^2S_{1/2} \rightarrow ^2D_{3/2}$ 435.5 nm transition in $^{171}$Yb$^+$. The ion trap will be based on a micro-fabricated circuit, with surface electrodes generating a trap** potential to localize a single Yb ion a few hundred $μ$m from the electrodes. We present our trap design as well as simulations of the resulting trap** pseudo-…
▽ More
We present the design of a compact optical clock based on the $^2S_{1/2} \rightarrow ^2D_{3/2}$ 435.5 nm transition in $^{171}$Yb$^+$. The ion trap will be based on a micro-fabricated circuit, with surface electrodes generating a trap** potential to localize a single Yb ion a few hundred $μ$m from the electrodes. We present our trap design as well as simulations of the resulting trap** pseudo-potential. We also present a compact, multi-channel wavelength meter that will permit the frequency stabilization of the cooling, repum** and clear-out lasers at 369.5 nm, 935.2 nm and 638.6 nm needed to cool the ion. We use this wavelength meter to characterize and stabilize the frequency of extended cavity diode lasers at 369.5 nm and 638.6 nm.
△ Less
Submitted 18 March, 2016;
originally announced March 2016.
-
Frequency stability of a wavelength meter and applications to laser frequency stabilization
Authors:
Khaldoun Saleh,
Jacques Millo,
Alexandre Didier,
Yann Kersalé,
Clément Lacroûte
Abstract:
Interferometric wavelength meters have attained frequency resolutions down to the MHz range. In particular, Fizeau interferometers, which have no moving parts, are becoming a popular tool for laser characterization and stabilization. In this article, we characterize such a wavelength meter using an ultra-stable laser in terms of relative frequency instability $σ_y(τ)$ and demonstrate that it can a…
▽ More
Interferometric wavelength meters have attained frequency resolutions down to the MHz range. In particular, Fizeau interferometers, which have no moving parts, are becoming a popular tool for laser characterization and stabilization. In this article, we characterize such a wavelength meter using an ultra-stable laser in terms of relative frequency instability $σ_y(τ)$ and demonstrate that it can achieve a short-term instability $σ_y(1 s) \approx 2{\times}10^{-10}$ and a frequency drift of order $10$ MHz/day. We use this apparatus to demonstrate frequency control of a near-infrared laser, where a frequency instability below $3{\times}10^{-10}$ from 1 s to 2000 s is achieved. Such performance is for example adequate for ions trap** and atoms cooling experiments.
△ Less
Submitted 15 December, 2015;
originally announced December 2015.
-
Characterization of the individual short-term frequency stability of Cryogenic Sapphire Oscillators at the 1e-16 level
Authors:
Christophe Fluhr,
Serge Grop,
Benoît Dubois,
Yann Kersalé,
Enrico Rubiola,
Vincent Giordano
Abstract:
We present the characterisation of three Cryogenic Sapphire Oscillators using the three-corner-hat method. Easily implemented with commercial components and instruments, this method reveals itself very useful to analyse the frequency stability limitations of these state-of-the-art ultra-stable oscillators. The best unit presents a fractional frequency stability better than 5e-16 at 1 s and below 2…
▽ More
We present the characterisation of three Cryogenic Sapphire Oscillators using the three-corner-hat method. Easily implemented with commercial components and instruments, this method reveals itself very useful to analyse the frequency stability limitations of these state-of-the-art ultra-stable oscillators. The best unit presents a fractional frequency stability better than 5e-16 at 1 s and below 2e-16 for integration times less than 5,000s.
△ Less
Submitted 10 December, 2015;
originally announced December 2015.
-
Ultra-low phase noise all-optical microwave generation setup based on commercial devices
Authors:
A. Didier,
J. Millo,
S. Grop,
B. Dubois,
E. Bigler,
E. Rubiola,
C. Lacroûte,
Y. Kersalé
Abstract:
In this paper, we present a very simple design based on commercial devices for the all-optical generation of ultra-low phase noise microwave signals. A commercial, fibered femtosecond laser is locked to a laser that is stabilized to a commercial ULE Fabry-Perot cavity. The 10 GHz microwave signal extracted from the femtosecond laser output exhibits a single sideband phase noise…
▽ More
In this paper, we present a very simple design based on commercial devices for the all-optical generation of ultra-low phase noise microwave signals. A commercial, fibered femtosecond laser is locked to a laser that is stabilized to a commercial ULE Fabry-Perot cavity. The 10 GHz microwave signal extracted from the femtosecond laser output exhibits a single sideband phase noise $\mathcal{L}(f)=-104 \ \mathrm{dBc}/\mathrm{Hz}$ at 1 Hz Fourier frequency, at the level of the best value obtained with such "microwave photonics" laboratory experiments \cite{Fortier2011}. Close-to-the-carrier ultra-low phase noise microwave signals will now be available in laboratories outside the frequency metrology field, opening up new possibilities in various domains.
△ Less
Submitted 20 March, 2015;
originally announced March 2015.
-
Influence of the ESR saturation on the power sensitivity of cryogenic sapphire resonators
Authors:
Vincent Giordano,
Serge Grop,
Pierre-Yves Bourgeois,
Yann Kersalé,
Enrico Rubiola
Abstract:
Here, we study the paramagnetic ions behavior in presence of a strong microwave electromagnetic field sustained inside a cryogenic sapphire whispering gallery mode resonator. The high frequency measurement resolution that can be now achieved by comparing two CSOs permit for the first time to observe clearly the non-linearity of the resonator power sensitivity. These observations that in turn allow…
▽ More
Here, we study the paramagnetic ions behavior in presence of a strong microwave electromagnetic field sustained inside a cryogenic sapphire whispering gallery mode resonator. The high frequency measurement resolution that can be now achieved by comparing two CSOs permit for the first time to observe clearly the non-linearity of the resonator power sensitivity. These observations that in turn allow us to optimize the CSO operation, are well explained by the Electron Spin Resonance (ESR) saturation of the paramagnetic impurities contained in the sapphire crystal.
△ Less
Submitted 13 May, 2014;
originally announced May 2014.
-
Controlling the Frequency-Temperature Sensitivity of a Cryogenic Sapphire Maser Frequency Standard by Manipulating Fe3+ Spins in the Sapphire Lattice
Authors:
Karim Benmessai,
Daniel L. Creedon,
Mohamad Mrad,
Jean-Michel Le Floch,
Pierre-Yves Bourgeois,
Yann Kersalé,
Vincent Giordano,
Michael E. Tobar
Abstract:
To create a stable signal from a cryogenic sapphire maser frequency standard, the frequency-temperature dependence of the supporting Whispering Gallery mode must be annulled. We report the ability to control this dependence by manipulating the paramagnetic susceptibility of Fe3+ ions in the sapphire lattice. We show that the maser signal depends on other Whispering Gallery modes tuned to the pump…
▽ More
To create a stable signal from a cryogenic sapphire maser frequency standard, the frequency-temperature dependence of the supporting Whispering Gallery mode must be annulled. We report the ability to control this dependence by manipulating the paramagnetic susceptibility of Fe3+ ions in the sapphire lattice. We show that the maser signal depends on other Whispering Gallery modes tuned to the pump signal near 31 GHz, and the annulment point can be controlled to exist between 5 to 10 K depending on the Fe3+ ion concentration and the frequency of the pump. This level of control has not been achieved previously, and will allow improvements in the stability of such devices.
△ Less
Submitted 16 January, 2012;
originally announced January 2012.
-
Fe3+ paramagnetic ion in α-Al2 O3 energy levels revisited. Application to a 31 GHz Maser proposal
Authors:
M. Mrad,
P. Y. Bourgeois,
Y. Kersalé,
V. Giordano
Abstract:
The molecular structure of a 3d 5 configuration ion in a trigonal ligand field is theoretically established on the basis of the 252\times252 complete energy matrice. The optical absorption and the electron paramagnetic resonance spectra of the Fe3+ ion in the sapphire crystal (α-Al2 O3) have been studied by diagonalizing the complete energy matrice. The calculated results are in very good agreemen…
▽ More
The molecular structure of a 3d 5 configuration ion in a trigonal ligand field is theoretically established on the basis of the 252\times252 complete energy matrice. The optical absorption and the electron paramagnetic resonance spectra of the Fe3+ ion in the sapphire crystal (α-Al2 O3) have been studied by diagonalizing the complete energy matrice. The calculated results are in very good agreement with previous experimental observations. The strength of the transition probabilities between pairs of the energy levels have been calculated to determine the possibility to achieve a population inversion in the ground state by applying optical pum** to the crystal. Preliminary results based on the computed transition parameters and on the maser rate equations model show that a 31 GHz maser signal can be effectively generated depending on the cryogenic resonator design.
△ Less
Submitted 9 January, 2012;
originally announced January 2012.
-
Advanced noise reduction techniques for ultra-low phase noise optical-to-microwave division with femtosecond fiber combs
Authors:
W. Zhang,
Z. Xu,
M. Lours,
R. Boudot,
Y. Kersale,
A. N. Luiten,
Y. Le Coq,
G. Santarelli
Abstract:
We report what we believe to be the lowest phase noise optical-to-microwave frequency division using fiber-based femtosecond optical frequency combs: a residual phase noise of -120dBc/Hz at 1 Hz offset from a 11.55GHz carrier frequency. We furthermore report a detailed investigation into the fundamental noise sources which afflicts the division process itself. Two frequency combs with quasi-identi…
▽ More
We report what we believe to be the lowest phase noise optical-to-microwave frequency division using fiber-based femtosecond optical frequency combs: a residual phase noise of -120dBc/Hz at 1 Hz offset from a 11.55GHz carrier frequency. We furthermore report a detailed investigation into the fundamental noise sources which afflicts the division process itself. Two frequency combs with quasi-identical configurations are referenced to a common ultrastable cavity laser source. To identify each of the limiting effects we implement an ultra-low noise carrier-suppression measurement system, which circumvents the detection and amplification noise of more conventional techniques. This technique now allows the suppression of these unwanted sources of noise to very low levels. In the Fourier frequency range of ~200 Hz to 100 kHz, a fed-forward technique based on a voltage-controlled phase shifter delivers a further noise reduction of 10 dB. For lower Fourier frequencies, optical power stabilization is implemented in order to reduce the relative intensity noise which causes unwanted phase noise through power to phase conversion in the detector. We implement and compare two possible control schemes based on an acousto-optical modulator and comb pump current. We also present wideband measurements on the relative intensity noise of the fiber comb.
△ Less
Submitted 9 March, 2011; v1 submitted 3 December, 2010;
originally announced December 2010.
-
Unprecedented High Long Term Frequency Stability with a Macroscopic Resonator Oscillator
Authors:
Serge Grop,
Wolfgang Schäfer,
Pierre-Yves Bourgeois,
Nicolas Bazin,
Yann Kersalé,
Mark Oxborrow,
Enrico Rubiola,
Vincent Giordano
Abstract:
This article reports on the long-term frequency stabilty characterisation of a new type of cryogenic sapphire oscillator using an autonomous pulse-tube cryocooler as its cold source. This new design enables a relative frequency stability of better than 4.5e-15 over one day of integration. This represents to our knowledge the best long-term frequency stability ever obtained with a signal source bas…
▽ More
This article reports on the long-term frequency stabilty characterisation of a new type of cryogenic sapphire oscillator using an autonomous pulse-tube cryocooler as its cold source. This new design enables a relative frequency stability of better than 4.5e-15 over one day of integration. This represents to our knowledge the best long-term frequency stability ever obtained with a signal source based on a macroscopic resonator.
△ Less
Submitted 3 November, 2010;
originally announced November 2010.
-
DC-powered Fe3+:sapphire Maser and its Sensitivity to Ultraviolet Light
Authors:
Mark Oxborrow,
Pierre-Yves Bourgeois,
Yann Kersalé,
Vincent Giordano
Abstract:
The zero-field Fe3+:sapphire whispering-gallery-mode maser oscillator exhibits several alluring features: Its output is many orders of magnitude brighter than that of an active hydrogen maser and thus far less degraded by spontaneous-emission (Schawlow-Townes) and/or receiving-amplifier noise. Its oscillator loop is confined to a piece of mono-crystalline rock bolted into a metal can. Its quiet am…
▽ More
The zero-field Fe3+:sapphire whispering-gallery-mode maser oscillator exhibits several alluring features: Its output is many orders of magnitude brighter than that of an active hydrogen maser and thus far less degraded by spontaneous-emission (Schawlow-Townes) and/or receiving-amplifier noise. Its oscillator loop is confined to a piece of mono-crystalline rock bolted into a metal can. Its quiet amplification combined with high resonator Q provide the ingredients for exceptionally low phase noise. We here concentrate on novelties addressing the fundamental conundrums and technical challenges that impede progress. (1) Roasting: The "mase-ability" of sapphire depends significantly on the chemical conditions under which it is grown and heat-treated. We provide some fresh details and nuances here. (2) Simplification: This paper obviates the need for a Ka-band synthesizer: it describes how a 31.3 GHz loop oscillator, operating on the preferred WG pump mode, incorporating Pound locking, was built from low-cost components. (3) "Dark Matter": A Siegman-level analysis of the experimental data determines the substitutional concentration of Fe3+ in HEMEX to be less than a part per billion prior to roasting and up to a few hundred ppb afterwards. Chemical assays, using different techniques (incl. glow discharge mass spectra spectroscopy and neutron activation analysis) consistently indicate, however, that HEMEX contains iron at concentrations of a few parts per million. Drawing from several forgotten-about/under-appreciated papers, this substantial discrepancy is addressed. (4) Excitons: Towards providing a new means of controlling the Fe3+:sapph. system, a cryogenic sapphire ring was illuminated, whilst masing, with UV light at wavelengths corresponding to known electronic and charge-transfer (thus valence-altering) transitions. Preliminary experiments are reported.
△ Less
Submitted 26 April, 2010; v1 submitted 23 April, 2010;
originally announced April 2010.
-
Sub-100 attoseconds optics-to-microwave synchronization
Authors:
W. Zhang,
Z. Xu,
M. Lours,
R. Boudot,
Y. Kersale,
G. Santarelli,
Y. Le Coq
Abstract:
We use two fiber-based femtosecond frequency combs and a low-noise carrier suppression phase detection system to characterize the optical to microwave synchronization achievable with such frequency divider systems. By applying specific noise reduction strategies, a residual phase noise as low as -120 dBc/Hz at 1 Hz offset frequency from a 11.55 GHz carrier is measured. The fractional frequency ins…
▽ More
We use two fiber-based femtosecond frequency combs and a low-noise carrier suppression phase detection system to characterize the optical to microwave synchronization achievable with such frequency divider systems. By applying specific noise reduction strategies, a residual phase noise as low as -120 dBc/Hz at 1 Hz offset frequency from a 11.55 GHz carrier is measured. The fractional frequency instability from a single optical-to-frequency divider is 1.1E-16 at 1 s averaging down to below 2E-19 after only 1000 s. The corresponding rms time deviation is lower than 100 attoseconds up to 1000 s averaging duration.
△ Less
Submitted 14 March, 2010;
originally announced March 2010.
-
ELISA: a cryocooled 10 GHz oscillator with 10-15 frequency stability
Authors:
S. Grop,
P. Y. Bourgeois,
N. Bazin,
Y. Kersale,
E. Rubiola,
C. Langham,
M. Oxborrow,
D. Clapton,
S. Walker,
J. De Vicente,
V. Giordano
Abstract:
This article reports the design, the breadboarding and the validation of an ultra-stable Cryogenic Sapphire Oscillator operated in an autonomous cryocooler. The objective of this project was to demonstrate the feasibility of a frequency stability of 3x10-15 between 1 s and 1,000 s for the European Space Agency deep space stations. This represents the lowest fractional frequency instability ever…
▽ More
This article reports the design, the breadboarding and the validation of an ultra-stable Cryogenic Sapphire Oscillator operated in an autonomous cryocooler. The objective of this project was to demonstrate the feasibility of a frequency stability of 3x10-15 between 1 s and 1,000 s for the European Space Agency deep space stations. This represents the lowest fractional frequency instability ever achieved with cryocoolers. The preliminary results presented in this paper validate the design we adopted for the sapphire resonator, the cold source and the oscillator loop.
△ Less
Submitted 22 September, 2009;
originally announced September 2009.
-
Ultra-Low Noise Microwave Extraction from Fiber-Based Optical Frequency Comb
Authors:
J. Millo,
R. Boudot,
M. Lours,
P. Y. Bourgeois,
A. N. Luiten,
Y. Le Coq,
Y. Kersale,
G. Santarelli
Abstract:
In this letter, we report on all-optical fiber approach to the generation of ultra-low noise microwave signals. We make use of two erbium fiber mode-locked lasers phase locked to a common ultra-stable laser source to generate an 11.55 GHz signal with an unprecedented relative phase noise of -111 dBc/Hz at 1 Hz from the carrier.The residual frequency instability of the microwave signals derived f…
▽ More
In this letter, we report on all-optical fiber approach to the generation of ultra-low noise microwave signals. We make use of two erbium fiber mode-locked lasers phase locked to a common ultra-stable laser source to generate an 11.55 GHz signal with an unprecedented relative phase noise of -111 dBc/Hz at 1 Hz from the carrier.The residual frequency instability of the microwave signals derived from the two optical frequency combs is below 2.3 10^(-16) at 1s and about 4 10^(-19) at 6.5 10^(4)s (in 5 Hz bandwidth, three days continuous operation).
△ Less
Submitted 21 November, 2009; v1 submitted 25 June, 2009;
originally announced June 2009.
-
Creating traveling waves from standing waves from the gyrotropic paramagnetic properties of Fe$^{3+}$ ions in a high-Q whispering gallery mode sapphire resonator
Authors:
Karim Benmessai,
Michael Edmund Tobar,
Nicholas Bazin,
Pierre-Yves Bourgeois,
Yann Kersale,
Vincent Giordano
Abstract:
We report observations of the gyrotropic change in magnetic susceptibility of the Fe$^{3+}$ electron paramagnetic resonance at 12.037GHz (between spin states $|1/2>$ and $|3/2>$) in sapphire with respect to applied magnetic field. Measurements were made by observing the response of the high-Q Whispering Gallery doublet (WGH$_{\pm17,0,0}$) in a Hemex sapphire resonator cooled to 5 K. The doublets…
▽ More
We report observations of the gyrotropic change in magnetic susceptibility of the Fe$^{3+}$ electron paramagnetic resonance at 12.037GHz (between spin states $|1/2>$ and $|3/2>$) in sapphire with respect to applied magnetic field. Measurements were made by observing the response of the high-Q Whispering Gallery doublet (WGH$_{\pm17,0,0}$) in a Hemex sapphire resonator cooled to 5 K. The doublets initially existed as standing waves at zero field and were transformed to traveling waves due to the gyrotropic response.
△ Less
Submitted 21 May, 2009;
originally announced May 2009.
-
Measurement of fundamental thermal noise limit in a cryogenic sapphire frequency standard using bimodal maser oscillations
Authors:
Karim Benmessai,
Daniel Lloyd Creedon,
Michael Edmund Tobar,
Pierre-Yves Bourgeois,
Yann Kersale,
Vincent Giordano
Abstract:
We report observations of the Schawlow-Townes noise limit in a cryogenic sapphire secondary frequency standard. The effect causes a fundamental limit to the frequency stability, and was measured through the novel excitation of a bimodal maser oscillation of a Whispering Gallery doublet at $12.04 GHz$. The beat frequency of $10 kHz$ between the oscillations enabled a sensitive probe for this meas…
▽ More
We report observations of the Schawlow-Townes noise limit in a cryogenic sapphire secondary frequency standard. The effect causes a fundamental limit to the frequency stability, and was measured through the novel excitation of a bimodal maser oscillation of a Whispering Gallery doublet at $12.04 GHz$. The beat frequency of $10 kHz$ between the oscillations enabled a sensitive probe for this measurement of fractional frequency instability of $10^{-14}τ^{-1/2}$ with only 0.5 $pW$ of output power.
△ Less
Submitted 16 July, 2008;
originally announced July 2008.
