Showing 1–12 of 12 results for author: Kate, H H J t

Training performance of Nb3Sn Rutherford cables in a channel with a wide range of impregnation materials

Authors: S. Otten, A. Kario, W. A. J. Wessel. J. Leferink, H. H. J. ten Kate, M. Daly, C. Hug, S. Sidorov, A. Brem, B. Auchmann, P. Studer, T. Tervoort

Abstract: Training of accelerator magnets is a costly and time consuming process. The number of training quenches must therefore be reduced to a minimum. We investigate training of impregnated Nb3Sn Rutherford cable in a small-scale experiment. The test involves a Rutherford cable impregnated in a meandering channel simulating the environment of a canted-cosine-theta (CCT) coil. The sample is powered using… ▽ More Training of accelerator magnets is a costly and time consuming process. The number of training quenches must therefore be reduced to a minimum. We investigate training of impregnated Nb3Sn Rutherford cable in a small-scale experiment. The test involves a Rutherford cable impregnated in a meandering channel simulating the environment of a canted-cosine-theta (CCT) coil. The sample is powered using a transformer and the Lorentz force is generated by an externally applied magnetic field. The low material and helium consumption enable the test of a larger number of samples. In this article, we present training of samples impregnated with alumina-filled epoxy resins, a modified resin with paraffin-like mechanical properties, and a new tough resin in development at ETH Zürich. These new data are compared with previous results published earlier. Compared to samples with unfilled epoxy resin, those with alumina-filled epoxy show favorable training properties with higher initial quench currents and fewer training quenches before reaching 80% of the critical current. △ Less

Submitted 18 November, 2022; originally announced November 2022.

Comments: 4 pages, 6 figures. Submitted to IEEE Transactions on Applied Superconductivity (TAS) for publication in the ASC2022 special issue. Copyright of the article was transferred to IEEE by submission

Comparison of the Baseline and the Minimal Steel Yoke Superconducting Magnets for the Future Circular Hadron-Hadron Collider

Authors: V. I. Klyukhin, A. Ball, C. P. Berriaud, E. Bielert, B. Curé, A. Dudarev, A. Gaddi, H. Gerwig, A. Hervé, M. Mentink, H. Pais Da Silva, U. Wagner, H. H. J. Ten Kate

Abstract: The conceptual design study of a hadron Future Circular hadron-hadron Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV assumes using in the experimental detector the superconducting magnetic system with a central magnetic flux density of an order of 4 T. A superconducting magnet with a minimal steel yoke was proposed as an alternative to the baseline iron-free solenoids. In a… ▽ More The conceptual design study of a hadron Future Circular hadron-hadron Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV assumes using in the experimental detector the superconducting magnetic system with a central magnetic flux density of an order of 4 T. A superconducting magnet with a minimal steel yoke was proposed as an alternative to the baseline iron-free solenoids. In a present study, both designs are modeled with Cobham's program TOSCA and compared. All the main parameters are discussed. △ Less

Submitted 18 January, 2022; originally announced January 2022.

Comments: 7 pages, 9 figures, 5 references. Presented at ICSM2018 - 6th International Conference on Superconductivity and Magnetism 2018, 29 April - 4 May, Antalya Turkey

Conceptual Design of BabyIAXO, the intermediate stage towards the International Axion Observatory

Authors: A. Abeln, K. Altenmüller, S. Arguedas Cuendis, E. Armengaud, D. Attié, S. Aune, S. Basso, L. Bergé, B. Biasuzzi, P. T. C. Borges De Sousa, P. Brun, N. Bykovskiy, D. Calvet, J. M. Carmona, J. F. Castel, S. Cebrián, V. Chernov, F. E. Christensen, M. M. Civitani, C. Cogollos, T. Dafní, A. Derbin, K. Desch, D. Díez, M. Dinter , et al. (101 additional authors not shown)

Abstract: This article describes BabyIAXO, an intermediate experimental stage of the International Axion Observatory (IAXO), proposed to be sited at DESY. IAXO is a large-scale axion helioscope that will look for axions and axion-like particles (ALPs), produced in the Sun, with unprecedented sensitivity. BabyIAXO is conceived to test all IAXO subsystems (magnet, optics and detectors) at a relevant scale for… ▽ More This article describes BabyIAXO, an intermediate experimental stage of the International Axion Observatory (IAXO), proposed to be sited at DESY. IAXO is a large-scale axion helioscope that will look for axions and axion-like particles (ALPs), produced in the Sun, with unprecedented sensitivity. BabyIAXO is conceived to test all IAXO subsystems (magnet, optics and detectors) at a relevant scale for the final system and thus serve as prototype for IAXO, but at the same time as a fully-fledged helioscope with relevant physics reach itself, and with potential for discovery. The BabyIAXO magnet will feature two 10 m long, 70 cm diameter bores, and will host two detection lines (optics and detector) of dimensions similar to the final ones foreseen for IAXO. BabyIAXO will detect or reject solar axions or ALPs with axion-photon couplings down to $g_{aγ} \sim 1.5 \times 10^{-11}$ GeV$^{-1}$, and masses up to $m_a\sim 0.25$ eV. BabyIAXO will offer additional opportunities for axion research in view of IAXO, like the development of precision x-ray detectors to identify particular spectral features in the solar axion spectrum, and the implementation of radiofrequency-cavity-based axion dark matter setups. △ Less

Submitted 4 March, 2021; v1 submitted 22 October, 2020; originally announced October 2020.

Comments: 77 pages, 49 figures. Prepared for submission to JHEP. Third version after referees comments

High magnetic fields for fundamental physics

Authors: Rémy Battesti, Jerome Beard, Sebastian Böser, Nicolas Bruyant, Dmitry Budker, Scott A. Crooker, Edward J. Daw, Victor V. Flambaum, Toshiaki Inada, Igor G. Irastorza, Felix Karbstein, Dong Lak Kim, Mikhail G. Kozlov, Ziad Melhem, Arran Phipps, Pierre Pugnat, Geert Rikken, Carlo Rizzo, Matthias Schott, Yannis K. Semertzidis, Herman H. J. ten Kate, Guido Zavattini

Abstract: Various fundamental-physics experiments such as measurement of the birefringence of the vacuum, searches for ultralight dark matter (e.g., axions), and precision spectroscopy of complex systems (including exotic atoms containing antimatter constituents) are enabled by high-field magnets. We give an overview of current and future experiments and discuss the state-of-the-art DC- and pulsed-magnet te… ▽ More Various fundamental-physics experiments such as measurement of the birefringence of the vacuum, searches for ultralight dark matter (e.g., axions), and precision spectroscopy of complex systems (including exotic atoms containing antimatter constituents) are enabled by high-field magnets. We give an overview of current and future experiments and discuss the state-of-the-art DC- and pulsed-magnet technologies and prospects for future developments. △ Less

Submitted 20 March, 2018; originally announced March 2018.

Comments: 49 pages, 32 figures

Superconducting Magnet with a Minimal Steel Yoke for the Future Circular Collider Detector

Authors: V. I. Klyukhin, A. Hervé, A. Ball, B. Curé, A. Dudarev, A. Gaddi, H. Gerwig, M. Mentink, H. Pais Da Silva, G. Rolando, H. H. J. Ten Kate, C. P. Berriaud

Abstract: The conceptual design study of a Future Circular hadron-hadron Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV, assumed to be constructed in a new tunnel of 80-100 km circumference, includes the determination of the basic requirements for its detectors. A superconducting solenoid magnet of 12-m-diameter inner bore with the central magnetic flux density of 6 T, in combination… ▽ More The conceptual design study of a Future Circular hadron-hadron Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV, assumed to be constructed in a new tunnel of 80-100 km circumference, includes the determination of the basic requirements for its detectors. A superconducting solenoid magnet of 12-m-diameter inner bore with the central magnetic flux density of 6 T, in combination with two superconducting dipole magnets and two conventional toroid magnets is proposed for an FCC-hh experimental setup. The coil of 23.468 m length has seven 3.35-m-long modules included into one cryostat. The steel yoke with a mass of 22.6 kt consists of two barrel layers of 0.5 m radial thickness and a 0.7-m-thick nose disk and four 0.6-m-thick end-cap disks each side. The outer diameter of the yoke is 17.7 m. The full length of the magnetic system is 62.6 m. The air gaps between the end-cap disks provide for the installation of the muon chambers up to an absolute pseudorapidity about 2.7. The superconducting dipole magnets provide measurement of charged particle momenta in the absolute pseudorapidity region greater than 3. The conventional forward muon spectrometer allows muon identification in the absolute pseudorapidity region from 2.7 to 5. The magnet is modeled with the program TOSCA from Cobham CTS Limited. The total current in the superconducting solenoid coil is 123 MA-turns; the stored energy is 41.8 GJ. The axial force acting on each end-cap is 450 MN. The stray field is 13.7 mT at a radius of 50 m from the coil axis, and 5.2 mT at a radius of 100 m. Many other parameters are presented and discussed. △ Less

Submitted 8 August, 2016; v1 submitted 27 May, 2016; originally announced May 2016.

Comments: 8 pages, 6 figures, presented at ICSM2016 - 5th International Conference on Superconductivity and Magnetism on April 26, 2016 at Fethiye, Turkey

Journal ref: Journal of Superconductivity and Novel Magnetism, Article 3660 (2016)

Superconducting Magnet with the Reduced Barrel Yoke for the Hadron Future Circular Collider

Authors: V. I. Klyukhin, A. Ball, C. Berriaud, B. Curé, A. Dudarev, A. Gaddi, H. Gerwig, A. Hervé, M. Mentink, G. Rolando, H. F. Pais Da Silva, U. Wagner, H. H. J. ten Kate

Abstract: The conceptual design study of a hadron Future Circular Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV in a new tunnel of 80-100 km circumference assumes the determination of the basic requirements for its detectors. A superconducting solenoid magnet of 12 m diameter inner bore with the central magnetic flux density of 6 T is proposed for a FCC-hh experimental setup. The co… ▽ More The conceptual design study of a hadron Future Circular Collider (FCC-hh) with a center-of-mass energy of the order of 100 TeV in a new tunnel of 80-100 km circumference assumes the determination of the basic requirements for its detectors. A superconducting solenoid magnet of 12 m diameter inner bore with the central magnetic flux density of 6 T is proposed for a FCC-hh experimental setup. The coil of 24.518 m long has seven 3.5 m long modules included into one cryostat. The steel yoke with a mass of 21 kt consists of two barrel layers of 0.5 m radial thickness, and 0.7 m thick nose disk, four 0.6 m thick end-cap disks, and three 0.8 m thick muon toroid disks each side. The outer diameter of the yoke is 17.7 m; the length without the forward muon toroids is 33 m. The air gaps between the end-cap disks provide the installation of the muon chambers up to the pseudorapidity of \pm 3.5. The conventional forward muon spectrometer provides the measuring of the muon momenta in the pseudorapidity region from \pm 2.7 to \pm 4.6. The magnet modeled with Cobham's program TOSCA. The total Ampere-turns in the superconducting solenoid coil are 127.25 MA-turns. The stored energy is 43.3 GJ. The axial force onto each end-cap is 480 MN. The stray field at the radius of 50 m off the coil axis is 14.1 mT and 5.4 mT at the radius of 100 m. All other parameters presented and discussed. △ Less

Submitted 6 November, 2015; originally announced November 2015.

Comments: 3 pages, 6 figures, presented on November 4, 2015 at the 2015 IEEE Nuclear Science Symposium, Town \& Country Hotel, San Diego, CA (31 October - 7 November 2015)

The influence of the Al stabilizer layer thickness on the normal zone propagation velocity in high current superconductors

Authors: I. Shilon, A. Dudarev, S. A. E. Langeslag, L. P. Martins, H. H. J. ten Kate

Abstract: The stability of high-current superconductors is challenging in the design of superconducting magnets. When the stability requirements are fulfilled, the protection against a quench must still be considered. A main factor in the design of quench protection systems is the resistance growth rate in the magnet following a quench. The usual method for determining the resistance growth in impregnated c… ▽ More The stability of high-current superconductors is challenging in the design of superconducting magnets. When the stability requirements are fulfilled, the protection against a quench must still be considered. A main factor in the design of quench protection systems is the resistance growth rate in the magnet following a quench. The usual method for determining the resistance growth in impregnated coils is to calculate the longitudinal velocity with which the normal zone propagates in the conductor along the coil windings. Here, we present a 2D numerical model for predicting the normal zone propagation velocity in Al stabilized Rutherford NbTi cables with large cross section. By solving two coupled differential equations under adiabatic conditions, the model takes into account the thermal diffusion and the current redistribution process following a quench. Both the temperature and magnetic field dependencies of the superconductor and the metal cladding materials properties are included. Unlike common normal zone propagation analyses, we study the influence of the thickness of the cladding on the propagation velocity for varying operating current and magnetic field. To assist in the comprehension of the numerical results, we also introduce an analytical formula for the longitudinal normal zone propagation. The analysis distinguishes between low-current and high-current regimes of normal zone propagation, depending on the ratio between the characteristic times of thermal and magnetic diffusion. We show that above a certain thickness, the cladding acts as a heat sink with a limited contribution to the acceleration of the propagation velocity with respect to the cladding geometry. Both numerical and analytical results show good agreement with experimental data. △ Less

Submitted 3 September, 2014; originally announced September 2014.

Comments: To be published in Physics Procedia (ICEC 25 conference special issue)

Modeling heat transfer from quench protection heaters to superconducting cables in Nb3Sn magnets

Authors: T. Salmi, D. Arbelaez, S. Caspi, H. Felice, S. Prestemon, G. Chlachidze, H. H. J. ten Kate

Abstract: We use a recently developed quench protection heater modeling tool for an analysis of heater delays in superconducting high-field Nb3Sn accelerator magnets. The results suggest that the calculated delays are consistent with experimental data, and show how the heater delay depends on the main heater design parameters. We use a recently developed quench protection heater modeling tool for an analysis of heater delays in superconducting high-field Nb3Sn accelerator magnets. The results suggest that the calculated delays are consistent with experimental data, and show how the heater delay depends on the main heater design parameters. △ Less

Submitted 16 January, 2014; originally announced January 2014.

Comments: 8 pages, Contribution to WAMSDO 2013: Workshop on Accelerator Magnet, Superconductor, Design and Optimization; 15 - 16 Jan 2013, CERN, Geneva, Switzerland

Journal ref: CERN Yellow Report CERN-2013-006, pp.30-37

The Superconducting Toroid for the New International AXion Observatory (IAXO)

Authors: I. Shilon, A. Dudarev, H. Silva, U. Wagner, H. H. J. ten Kate

Abstract: IAXO, the new International AXion Observatory, will feature the most ambitious detector for solar axions to date. Axions are hypothetical particles which were postulated to solve one of the puzzles arising in the standard model of particle physics, namely the strong CP (Charge conjugation and Parity) problem. This detector aims at achieving a sensitivity to the coupling between axions and photons… ▽ More IAXO, the new International AXion Observatory, will feature the most ambitious detector for solar axions to date. Axions are hypothetical particles which were postulated to solve one of the puzzles arising in the standard model of particle physics, namely the strong CP (Charge conjugation and Parity) problem. This detector aims at achieving a sensitivity to the coupling between axions and photons of one order of magnitude beyond the limits of the current detector, the CERN Axion Solar Telescope (CAST). The IAXO detector relies on a high-magnetic field distributed over a very large volume to convert solar axions to detectable X-ray photons. Inspired by the ATLAS barrel and end-cap toroids, a large superconducting toroid is being designed. The toroid comprises eight, one meter wide and twenty one meters long racetrack coils. The assembled toroid is sized 5.2 m in diameter and 25 m in length and its mass is about 250 tons. The useful field in the bores is 2.5 T while the peak magnetic field in the windings is 5.4 T. At the operational current of 12 kA the stored energy is 500 MJ. The racetrack type of coils are wound with a reinforced Aluminum stabilized NbTi/Cu cable and are conduction cooled. The coils optimization is shortly described as well as new concepts for cryostat, cold mass, supporting structure and the sun tracking system. Materials selection and sizing, conductor, thermal loads, the cryogenics system and the electrical system are described. Lastly, quench simulations are reported to demonstrate the system's safe quench protection scheme. △ Less

Submitted 9 September, 2013; originally announced September 2013.

Comments: To appear in IEEE Trans. Appl. Supercond. MT 23 issue. arXiv admin note: substantial text overlap with arXiv:1308.2526, arXiv:1212.4633

New Superconducting Toroidal Magnet System for IAXO, the International AXion Observatory

Authors: I. Shilon, A. Dudarev, H. Silva, U. Wagner, H. H. J. ten Kate

Abstract: Axions are hypothetical particles that were postulated to solve one of the puzzles arising in the standard model of particle physics, namely the strong CP (Charge conjugation and Parity) problem. The new International AXion Observatory (IAXO) will incorporate the most promising solar axions detector to date, which is designed to enhance the sensitivity to the axion-photon coupling by one order of… ▽ More Axions are hypothetical particles that were postulated to solve one of the puzzles arising in the standard model of particle physics, namely the strong CP (Charge conjugation and Parity) problem. The new International AXion Observatory (IAXO) will incorporate the most promising solar axions detector to date, which is designed to enhance the sensitivity to the axion-photon coupling by one order of magnitude beyond the limits of the current state-of-the-art detector, the CERN Axion Solar Telescope (CAST). The IAXO detector relies on a high-magnetic field distributed over a very large volume to convert solar axions into X-ray photons. Inspired by the successful realization of the ATLAS barrel and end-cap toroids, a very large superconducting toroid is currently designed at CERN to provide the required magnetic field. This toroid will comprise eight, one meter wide and twenty one meter long, racetrack coils. The system is sized 5.2 m in diameter and 25 m in length. Its peak magnetic field is 5.4 T with a stored energy of 500 MJ. The magnetic field optimization process to arrive at maximum detector yield is described. In addition, materials selection and their structure and sizing has been determined by force and stress calculations. Thermal loads are estimated to size the necessary cryogenic power and the concept of a forced flow supercritical helium based cryogenic system is given. A quench simulation confirmed the quench protection scheme. △ Less

Submitted 12 August, 2013; originally announced August 2013.

Comments: Accepted for publication in Adv. Cryo. Eng. (CEC/ICMC 2013 special issue)

IAXO - The International Axion Observatory

Authors: J. K. Vogel, F. T. Avignone, G. Cantatore, J. M. Carmona, S. Caspi, S. A. Cetin, F. E. Christensen, A. Dael, T. Dafni, M. Davenport, A. V. Derbin, K. Desch, A. Diago, A. Dudarev, C. Eleftheriadis, G. Fanourakis, E. Ferrer-Ribas, J. Galan, J. A. Garcia, J. G. Garza, T. Geralis, B. Gimeno, I. Giomataris, S. Gninenko, H. Gomez , et al. (39 additional authors not shown)

Abstract: The International Axion Observatory (IAXO) is a next generation axion helioscope aiming at a sensitivity to the axion-photon coupling of a few 10^{-12} GeV^{-1}, i.e. 1-1.5 orders of magnitude beyond sensitivities achieved by the currently most sensitive axion helioscope, the CERN Axion Solar Telescope (CAST). Crucial factors in improving the sensitivity for IAXO are the increase of the magnetic f… ▽ More The International Axion Observatory (IAXO) is a next generation axion helioscope aiming at a sensitivity to the axion-photon coupling of a few 10^{-12} GeV^{-1}, i.e. 1-1.5 orders of magnitude beyond sensitivities achieved by the currently most sensitive axion helioscope, the CERN Axion Solar Telescope (CAST). Crucial factors in improving the sensitivity for IAXO are the increase of the magnetic field volume together with the extensive use of x-ray focusing optics and low background detectors, innovations already successfully tested at CAST. Electron-coupled axions invoked to explain the white dwarf cooling, relic axions, and a large variety of more generic axion-like particles (ALPs) along with other novel excitations at the low-energy frontier of elementary particle physics could provide additional physics motivation for IAXO. △ Less

Submitted 13 February, 2013; originally announced February 2013.

Comments: 6 pages, 1 figure, Contribution to the 8th Patras Workshop on Axions, WIMPs and WISPs, Chicago, IL, USA, 2012

Conceptual Design of a New Large Superconducting Toroid for IAXO, the New International AXion Observatory

Authors: I. Shilon, A. Dudarev, H. Silva, H. H. J. ten Kate

Abstract: The International AXion Observatory (IAXO) will incorporate a new generation detector for axions, a hypothetical particle, which was postulated to solve one of the puzzles arising in the standard model of particle physics, namely the strong CP problem. The new IAXO experiment is aiming at achieving a sensitivity to the coupling between axions and photons of one order of magnitude beyond the limits… ▽ More The International AXion Observatory (IAXO) will incorporate a new generation detector for axions, a hypothetical particle, which was postulated to solve one of the puzzles arising in the standard model of particle physics, namely the strong CP problem. The new IAXO experiment is aiming at achieving a sensitivity to the coupling between axions and photons of one order of magnitude beyond the limits of the current state-of-the-art detector, represented by the CERN Axion Solar Telescope (CAST). The IAXO detector relies on a high-magnetic field distributed over a very large volume to convert solar axions into x-ray photons. Utilizing the designs of the ATLAS barrel and end-cap toroids, a large superconducting toroidal magnet is currently being designed at CERN to provide the required magnetic field. The new toroid will be built up from eight, one meter wide and 20 m long, racetrack coils. The toroid is sized about 4 m in diameter and 22 m in length. It is designed to realize a peak magnetic field of 5.4 T with a stored energy of 500 MJ. The magnetic field optimization process to arrive at maximum detector yield is described. In addition, force and stress calculations are performed to select materials and determine their structure and sizing. Conductor dimensionality, quench protection and the cryogenic design are dealt with as well. △ Less

Submitted 19 December, 2012; originally announced December 2012.

Comments: 5 pages, 5 figures. To be published in IEEE Trans. Appl. Supercond. 23 (ASC 2012 conference special issue)