-
Development of a prototype superconducting radio-frequency cavity for conduction-cooled accelerators
Authors:
G. Ciovati,
J. Anderson,
S. Balachandran,
G. Cheng,
B. Coriton,
E. Daly,
P. Dhakal,
A. Gurevich,
F. Hannon,
K. Harding,
L. Holland,
F. Marhauser,
K. McLaughlin,
D. Packard,
T. Powers,
U. Pudasaini,
J. Rathke,
R. Rimmer,
T. Schultheiss,
H. Vennekate,
D. Vollmer
Abstract:
The higher efficiency of superconducting radio-frequency (SRF) cavities compared to normal-conducting ones enables the development of high-energy continuous-wave linear accelerators (linacs). Recent progress in the development of high-quality Nb$_3$Sn film coatings along with the availability of cryocoolers with high cooling capacity at 4 K makes it feasible to operate SRF cavities cooled by therm…
▽ More
The higher efficiency of superconducting radio-frequency (SRF) cavities compared to normal-conducting ones enables the development of high-energy continuous-wave linear accelerators (linacs). Recent progress in the development of high-quality Nb$_3$Sn film coatings along with the availability of cryocoolers with high cooling capacity at 4 K makes it feasible to operate SRF cavities cooled by thermal conduction at relevant accelerating gradients for use in accelerators. A possible use of conduction-cooled SRF linacs is for environmental applications, requiring electron beams with energy of $1 - 10$ MeV and 1 MW of power. We have designed a 915 MHz SRF linac for such an application and developed a prototype single-cell cavity to prove the proposed design by operating it with cryocoolers at the accelerating gradient required for 1 MeV energy gain. The cavity has a $\sim 3$ $μ$m thick Nb$_3$Sn film on the inner surface, deposited on a $\sim4$ mm thick bulk Nb substrate and a bulk $\sim7$ mm thick Cu outer shell with three Cu attachment tabs. The cavity was tested up to a peak surface magnetic field of 53 mT in liquid He at 4.3 K. A horizontal test cryostat was designed and built to test the cavity cooled with three Gifford-McMahon cryocoolers. The rf tests of the conduction-cooled cavity, performed at General Atomics, achieved a peak surface magnetic field of 50 mT and stable operation was possible with up to 18.5 W of rf heat load. The peak frequency shift due to microphonics was 23 Hz. These results represent the highest peak surface magnetic field achieved in a conduction-cooled SRF cavity to date and meet the requirements for a 1 MeV energy gain.
△ Less
Submitted 22 March, 2023; v1 submitted 14 February, 2023;
originally announced February 2023.
-
Evaluation of silicon carbide as a divertor armor material in DIII-D H-mode discharges
Authors:
T. Abrams,
S. Bringuier,
D. M. Thomas,
G. Sinclair,
S. Gonderman,
L. Holland,
D. L. Rudakov,
R. S. Wilcox,
E. A. Unterberg,
F. Scotti
Abstract:
Silicon carbide (SiC) represents a promising but largely untested plasma-facing material (PFM) for next-step fusion devices. In this work, an analytic mixed-material erosion model is developed by calculating the physical (via SDTrimSP) and chemical (via empirical scalings) sputtering yield from SiC, Si, and C. The Si content in the near-surface SiC layer is predicted to increase during D plasma bo…
▽ More
Silicon carbide (SiC) represents a promising but largely untested plasma-facing material (PFM) for next-step fusion devices. In this work, an analytic mixed-material erosion model is developed by calculating the physical (via SDTrimSP) and chemical (via empirical scalings) sputtering yield from SiC, Si, and C. The Si content in the near-surface SiC layer is predicted to increase during D plasma bombardment due to more efficient physical and chemical sputtering of C relative to Si. Silicon erosion from SiC thereby occurs primarily from sputtering of the enriched Si layer, rather than directly from the SiC itself. SiC coatings on ATJ graphite, manufactured via chemical vapor deposition, were exposed to repeated H-mode plasma discharges in the DIII-D tokamak to test this model. The qualitative trends from analytic modeling are reproduced by the experimental measurements, obtained via spectroscopic inference using the S/XB method. Quantitatively the model slightly under-predicts measured erosion rates, which is attributed to uncertainties in the ion impact angle distribution, as well as the effect of edge-localized modes. After exposure, minimal changes to the macroscopic or microscopic surface morphology of the SiC coatings were observed. Compositional analysis reveals Si enrichment of about 10%, in line with expectations from the erosion model. Extrapolating to a DEMO-type device, an order-of-magnitude decrease in impurity sourcing, and up to a factor of 2 decrease in impurity radiation, is expected with SiC walls, relative to graphite, if low C plasma impurity content can be achieved. These favorable erosion properties motivate further investigations of SiC as a low-Z, non-metallic PFM.
△ Less
Submitted 8 April, 2021;
originally announced April 2021.
-
Design of a cw, low energy, high power superconducting linac for environmental applications
Authors:
G. Ciovati,
J. Anderson,
B. Coriton,
J. Guo,
F. Hannon,
L. Holland,
M. LeSher,
F. Marhauser,
J. Rathke,
R. Rimmer,
T. Schultheiss,
V. Vylet
Abstract:
The treatment of flue gases from power plants and municipal or industrial wastewater using electron beam irradiation technology has been successfully demonstrated in small-scale pilot plants. The beam energy requirement is rather modest, on the order of a few MeV, however the adoption of the technology at an industrial scale requires the availability of high beam power, of the order of 1 MW, in a…
▽ More
The treatment of flue gases from power plants and municipal or industrial wastewater using electron beam irradiation technology has been successfully demonstrated in small-scale pilot plants. The beam energy requirement is rather modest, on the order of a few MeV, however the adoption of the technology at an industrial scale requires the availability of high beam power, of the order of 1 MW, in a cost effective way. In this article we present the design of a compact superconducting accelerator capable of delivering a cw electron beam with a current of 1 A and an energy of 1 MeV. The main components are an rf-gridded thermionic gun and a conduction cooled beta= 0.5 elliptical Nb3Sn cavity with dual coaxial power couplers. An engineering and cost analysis shows that the proposed design would result in a processing cost competitive with alternative treatment methods.
△ Less
Submitted 11 June, 2018; v1 submitted 22 February, 2018;
originally announced February 2018.
