-
Investigation of the cryogenic scintillation of pure and doped sodium-iodine
Authors:
M. Clark,
F. Froborg,
P. C. F. Di Stefano,
F. Calaprice
Abstract:
We have studied the scintillation of pure and doped sodium iodide crystals handled in low humidity conditions under external $α$ and $γ$ excitation from room temperature down to 4K. The light yield of pure sodium iodide was seen to increase at low temperatures by a factor 30 compared to room temperature, up to a maximum of 40 photons/keV under $γ$ excitation at 60K, stabilizing to 30 photons/keV a…
▽ More
We have studied the scintillation of pure and doped sodium iodide crystals handled in low humidity conditions under external $α$ and $γ$ excitation from room temperature down to 4K. The light yield of pure sodium iodide was seen to increase at low temperatures by a factor 30 compared to room temperature, up to a maximum of 40 photons/keV under $γ$ excitation at 60K, stabilizing to 30 photons/keV at lower temperatures. Thallium doped sodium iodide fluctuates by 20% around the room temperature value, stabilizing at 40 photons/keV at low temperature. $α/ γ$ quenching factor stabilizes at roughly 0.7 for both materials beneath 50K. Time constants of both materials slow greatly at low temperature, reaching tens of microseconds. Cryogenic applications of these materials are complexified by their mechanical fragility and hygroscopicity.
△ Less
Submitted 22 December, 2021;
originally announced December 2021.
-
The LUX-ZEPLIN (LZ) radioactivity and cleanliness control programs
Authors:
D. S. Akerib,
C. W. Akerlof,
D. Yu. Akimov,
A. Alquahtani,
S. K. Alsum,
T. J. Anderson,
N. Angelides,
H. M. Araújo,
A. Arbuckle,
J. E. Armstrong,
M. Arthurs,
H. Auyeung,
S. Aviles,
X. Bai,
A. J. Bailey,
J. Balajthy,
S. Balashov,
J. Bang,
M. J. Barry,
D. Bauer,
P. Bauer,
A. Baxter,
J. Belle,
P. Beltrame,
J. Bensinger
, et al. (365 additional authors not shown)
Abstract:
LUX-ZEPLIN (LZ) is a second-generation direct dark matter experiment with spin-independent WIMP-nucleon scattering sensitivity above $1.4 \times 10^{-48}$ cm$^{2}$ for a WIMP mass of 40 GeV/c$^{2}$ and a 1000 d exposure. LZ achieves this sensitivity through a combination of a large 5.6 t fiducial volume, active inner and outer veto systems, and radio-pure construction using materials with inherent…
▽ More
LUX-ZEPLIN (LZ) is a second-generation direct dark matter experiment with spin-independent WIMP-nucleon scattering sensitivity above $1.4 \times 10^{-48}$ cm$^{2}$ for a WIMP mass of 40 GeV/c$^{2}$ and a 1000 d exposure. LZ achieves this sensitivity through a combination of a large 5.6 t fiducial volume, active inner and outer veto systems, and radio-pure construction using materials with inherently low radioactivity content. The LZ collaboration performed an extensive radioassay campaign over a period of six years to inform material selection for construction and provide an input to the experimental background model against which any possible signal excess may be evaluated. The campaign and its results are described in this paper. We present assays of dust and radon daughters depositing on the surface of components as well as cleanliness controls necessary to maintain background expectations through detector construction and assembly. Finally, examples from the campaign to highlight fixed contaminant radioassays for the LZ photomultiplier tubes, quality control and quality assurance procedures through fabrication, radon emanation measurements of major sub-systems, and bespoke detector systems to assay scintillator are presented.
△ Less
Submitted 28 February, 2022; v1 submitted 3 June, 2020;
originally announced June 2020.
-
Annual Modulation in Direct Dark Matter Searches
Authors:
Francis Froborg,
Alan R Duffy
Abstract:
The measurement of an annual modulation in the event rate of direct dark matter detection experiments is a powerful tool for dark matter discovery. Indeed, several experiments have already claimed such a discovery in the past decade. While most of them have later revoked their conclusions, and others have found potentially contradictory results, one still stands today. This paper explains the pote…
▽ More
The measurement of an annual modulation in the event rate of direct dark matter detection experiments is a powerful tool for dark matter discovery. Indeed, several experiments have already claimed such a discovery in the past decade. While most of them have later revoked their conclusions, and others have found potentially contradictory results, one still stands today. This paper explains the potential as well as the challenges of annual modulation measurements, and gives an overview of past, present and future direct detection experiments.
△ Less
Submitted 3 May, 2020; v1 submitted 10 March, 2020;
originally announced March 2020.
-
The LUX-ZEPLIN (LZ) Experiment
Authors:
The LZ Collaboration,
D. S. Akerib,
C. W. Akerlof,
D. Yu. Akimov,
A. Alquahtani,
S. K. Alsum,
T. J. Anderson,
N. Angelides,
H. M. Araújo,
A. Arbuckle,
J. E. Armstrong,
M. Arthurs,
H. Auyeung,
X. Bai,
A. J. Bailey,
J. Balajthy,
S. Balashov,
J. Bang,
M. J. Barry,
J. Barthel,
D. Bauer,
P. Bauer,
A. Baxter,
J. Belle,
P. Beltrame
, et al. (357 additional authors not shown)
Abstract:
We describe the design and assembly of the LUX-ZEPLIN experiment, a direct detection search for cosmic WIMP dark matter particles. The centerpiece of the experiment is a large liquid xenon time projection chamber sensitive to low energy nuclear recoils. Rejection of backgrounds is enhanced by a Xe skin veto detector and by a liquid scintillator Outer Detector loaded with gadolinium for efficient n…
▽ More
We describe the design and assembly of the LUX-ZEPLIN experiment, a direct detection search for cosmic WIMP dark matter particles. The centerpiece of the experiment is a large liquid xenon time projection chamber sensitive to low energy nuclear recoils. Rejection of backgrounds is enhanced by a Xe skin veto detector and by a liquid scintillator Outer Detector loaded with gadolinium for efficient neutron capture and tagging. LZ is located in the Davis Cavern at the 4850' level of the Sanford Underground Research Facility in Lead, South Dakota, USA. We describe the major subsystems of the experiment and its key design features and requirements.
△ Less
Submitted 3 November, 2019; v1 submitted 20 October, 2019;
originally announced October 2019.
-
Monte Carlo simulation of the SABRE PoP background
Authors:
M. Antonello,
E. Barberio,
T. Baroncelli,
J. Benziger,
L. J. Bignell,
I. Bolognino,
F. Calaprice,
S. Copello,
D. D'Angelo,
G. D'Imperio,
I. Dafinei,
G. Di Carlo,
M. Diemoz,
A. Di Ludovico,
A. R. Duffy,
F. Froborg,
G. K. Giovanetti,
E. Hoppe,
A. Ianni,
L. Ioannucci,
S. Krishnan,
G. J. Lane,
I. Mahmood,
A. Mariani,
P. McGee
, et al. (23 additional authors not shown)
Abstract:
SABRE (Sodium-iodide with Active Background REjection) is a direct dark matter search experiment based on an array of radio-pure NaI(Tl) crystals surrounded by a liquid scintillator veto. Twin SABRE experiments in the Northern and Southern Hemispheres will differentiate a dark matter signal from seasonal and local effects. The experiment is currently in a Proof-of-Principle (PoP) phase, whose goal…
▽ More
SABRE (Sodium-iodide with Active Background REjection) is a direct dark matter search experiment based on an array of radio-pure NaI(Tl) crystals surrounded by a liquid scintillator veto. Twin SABRE experiments in the Northern and Southern Hemispheres will differentiate a dark matter signal from seasonal and local effects. The experiment is currently in a Proof-of-Principle (PoP) phase, whose goal is to demonstrate that the background rate is low enough to carry out an independent search for a dark matter signal, with sufficient sensitivity to confirm or refute the DAMA result during the following full-scale experimental phase. The impact of background radiation from the detector materials and the experimental site needs to be carefully investigated, including both intrinsic and cosmogenically activated radioactivity. Based on the best knowledge of the most relevant sources of background, we have performed a detailed Monte Carlo study evaluating the expected background in the dark matter search spectral region. The simulation model described in this paper guides the design of the full-scale experiment and will be fundamental for the interpretation of the measured background and hence for the extraction of a possible dark matter signal.
△ Less
Submitted 14 November, 2018; v1 submitted 25 June, 2018;
originally announced June 2018.
-
The SABRE project and the SABRE PoP
Authors:
M. Antonello,
E. Barberio,
T. Baroncelli,
J. Benziger,
L. J. Bignell,
I. Bolognino,
F. Calaprice,
S. Copello,
D. D'Angelo,
G. D'Imperio,
I. Dafinei,
G. Di Carlo,
M. Diemoz,
A. Di Ludovico,
W. Dix,
A. R. Duffy,
F. Froborg,
G. K. Giovanetti,
E. Hoppe,
A. Ianni,
L. Ioannucci,
S. Krishnan,
G. J. Lane,
I. Mahmood,
A. Mariani
, et al. (24 additional authors not shown)
Abstract:
SABRE aims to directly measure the annual modulation of the dark matter interaction rate with NaI(Tl) crystals. A modulation compatible with the standard hypothesis in which our Galaxy is embedded in a dark matter halo has been measured by the DAMA experiment in the same target material. Other direct detection experiments, using different target materials, seem to exclude the interpretation of suc…
▽ More
SABRE aims to directly measure the annual modulation of the dark matter interaction rate with NaI(Tl) crystals. A modulation compatible with the standard hypothesis in which our Galaxy is embedded in a dark matter halo has been measured by the DAMA experiment in the same target material. Other direct detection experiments, using different target materials, seem to exclude the interpretation of such modulation in the simplest scenario of WIMP-nucleon elastic scattering. The SABRE experiment aims to carry out an independent search with sufficient sensitivity to confirm or refute the DAMA claim. The SABRE concept and goal is to obtain a background rate of the order of 0.1 cpd/kg/keVee in the energy region of interest. This challenging goal is achievable by operating high-purity crystals inside a liquid scintillator veto for active background rejection. In addition, twin detectors will be located in the northern and southern hemispheres to identify possible contributions to the modulation from seasonal or site-related effects. The SABRE project includes an initial Proof-of-Principle phase at LNGS (Italy), to assess the radio-purity of the crystals and the efficiency of the liquid scintillator veto. This paper describes the general concept of SABRE and the expected sensitivity to WIMP annual modulation.
△ Less
Submitted 19 November, 2018; v1 submitted 25 June, 2018;
originally announced June 2018.
-
Speeding up complex multivariate data analysis in Borexino with parallel computing based on Graphics Processing Unit
Authors:
X. F. Ding,
M. Agostini,
K. Altenmuller,
S. Appel,
V. Atroshchenko,
Z. Bagdasarian,
D. Basilico,
G. Bellini,
J. Benziger,
D. Bick,
G. Bonfini,
D. Bravo,
B. Caccianiga,
F. Calaprice,
A. Caminata,
S. Caprioli,
M. Carlini,
P. Cavalcante,
A. Chepurnov,
K. Choi,
L. Collica,
D. D'Angelo,
S. Davini,
A. Derbin,
A. Di Ludovico
, et al. (82 additional authors not shown)
Abstract:
A spectral fitter based on the graphics processor unit (GPU) has been developed for Borexino solar neutrino analysis. It is able to shorten the fitting time to a superior level compared to the CPU fitting procedure. In Borexino solar neutrino spectral analysis, fitting usually requires around one hour to converge since it includes time-consuming convolutions in order to account for the detector re…
▽ More
A spectral fitter based on the graphics processor unit (GPU) has been developed for Borexino solar neutrino analysis. It is able to shorten the fitting time to a superior level compared to the CPU fitting procedure. In Borexino solar neutrino spectral analysis, fitting usually requires around one hour to converge since it includes time-consuming convolutions in order to account for the detector response and pile-up effects. Moreover, the convergence time increases to more than two days when including extra computations for the discrimination of $^{11}$C and external $γ$s. In sharp contrast, with the GPU-based fitter it takes less than 10 seconds and less than four minutes, respectively. This fitter is developed utilizing the GooFit project with customized likelihoods, pdfs and infrastructures supporting certain analysis methods. In this proceeding the design of the package, developed features and the comparison with the original CPU fitter are presented.
△ Less
Submitted 28 May, 2018;
originally announced May 2018.
-
Response of photomultiplier tubes to xenon scintillation light
Authors:
B. López Paredes,
H. M. Araújo,
F. Froborg,
N. Marangou,
I. Olcina,
T. J. Sumner,
R. Taylor,
A. Tomás,
A. Vacheret
Abstract:
We present the precision calibration of 35 Hamamatsu R11410-22 photomultiplier tubes (PMTs) with xenon scintillation light centred near 175 nm. This particular PMT variant was developed specifically for the LUX-ZEPLIN (LZ) dark matter experiment. A room-temperature xenon scintillation cell coupled to a vacuum cryostat was used to study the full-face PMT response at both room and low temperature…
▽ More
We present the precision calibration of 35 Hamamatsu R11410-22 photomultiplier tubes (PMTs) with xenon scintillation light centred near 175 nm. This particular PMT variant was developed specifically for the LUX-ZEPLIN (LZ) dark matter experiment. A room-temperature xenon scintillation cell coupled to a vacuum cryostat was used to study the full-face PMT response at both room and low temperature $\textrm{($\sim$ -100$^\circ$C)}$, in particular to determine the quantum efficiency (QE) and double photoelectron emission (DPE) probability in LZ operating conditions. For our sample with an average QE of $\textrm{(32.4$\pm$2.9)%}$ at room temperature, we find a relative improvement of $\textrm{(17.9$\pm$5.2)%}$ upon cooling (where uncertainty values refer to the sample standard deviation). The mean DPE probability in response to single vacuum ultraviolet (VUV) photons is $\textrm{(22.6$\pm$2.0)%}$ at low temperature; the DPE increase relative to room temperature, measured here for the first time, was $\textrm{(12.2$\pm$3.9)%}$. Evidence of a small triple photoelectron emission probability $\textrm{($\sim$0.6%)}$ has also been observed. Useful correlations are established between these parameters and the QE as measured by the manufacturer. The single VUV photon response is also measured for one ETEL D730/9829QB, a PMT with a more standard bialkali photocathode used in the ZEPLIN-III experiment, for which we obtained a cold DPE fraction of $\textrm{(9.1$\pm$0.1)%}$. Hence, we confirm that this effect is not restricted to the low-temperature bialkali photocathode technology employed by Hamamatsu. This highlights the importance of considering this phenomenon in the interpretation of data from liquid xenon scintillation and electroluminescence detectors, and from many other optical measurements in this wavelength region.
△ Less
Submitted 13 April, 2018; v1 submitted 4 January, 2018;
originally announced January 2018.
-
The Monte Carlo simulation of the Borexino detector
Authors:
M. Agostini,
K. Altenmuller,
S. Appel,
V. Atroshchenko,
Z. Bagdasarian,
D. Basilico,
G. Bellini,
J. Benziger,
D. Bick,
G. Bonfini,
L. Borodikhina,
D. Bravo,
B. Caccianiga,
F. Calaprice,
A. Caminata,
S. Caprioli,
M. Carlini,
P. Cavalcante,
A. Chepurnov,
K. Choi,
D. D'Angelo,
S. Davini,
A. Derbin,
X. F. Ding,
L. Di Noto
, et al. (75 additional authors not shown)
Abstract:
We describe the Monte Carlo (MC) simulation package of the Borexino detector and discuss the agreement of its output with data. The Borexino MC 'ab initio' simulates the energy loss of particles in all detector components and generates the resulting scintillation photons and their propagation within the liquid scintillator volume. The simulation accounts for absorption, reemission, and scattering…
▽ More
We describe the Monte Carlo (MC) simulation package of the Borexino detector and discuss the agreement of its output with data. The Borexino MC 'ab initio' simulates the energy loss of particles in all detector components and generates the resulting scintillation photons and their propagation within the liquid scintillator volume. The simulation accounts for absorption, reemission, and scattering of the optical photons and tracks them until they either are absorbed or reach the photocathode of one of the photomultiplier tubes. Photon detection is followed by a comprehensive simulation of the readout electronics response. The algorithm proceeds with a detailed simulation of the electronics chain. The MC is tuned using data collected with radioactive calibration sources deployed inside and around the scintillator volume. The simulation reproduces the energy response of the detector, its uniformity within the fiducial scintillator volume relevant to neutrino physics, and the time distribution of detected photons to better than 1% between 100 keV and several MeV. The techniques developed to simulate the Borexino detector and their level of refinement are of possible interest to the neutrino community, especially for current and future large-volume liquid scintillator experiments such as Kamland-Zen, SNO+, and Juno.
△ Less
Submitted 7 April, 2017;
originally announced April 2017.
-
LUX-ZEPLIN (LZ) Technical Design Report
Authors:
B. J. Mount,
S. Hans,
R. Rosero,
M. Yeh,
C. Chan,
R. J. Gaitskell,
D. Q. Huang,
J. Makkinje,
D. C. Malling,
M. Pangilinan,
C. A. Rhyne,
W. C. Taylor,
J. R. Verbus,
Y. D. Kim,
H. S. Lee,
J. Lee,
D. S. Leonard,
J. Li,
J. Belle,
A. Cottle,
W. H. Lippincott,
D. J. Markley,
T. J. Martin,
M. Sarychev,
T. E. Tope
, et al. (237 additional authors not shown)
Abstract:
In this Technical Design Report (TDR) we describe the LZ detector to be built at the Sanford Underground Research Facility (SURF). The LZ dark matter experiment is designed to achieve sensitivity to a WIMP-nucleon spin-independent cross section of three times ten to the negative forty-eighth square centimeters.
In this Technical Design Report (TDR) we describe the LZ detector to be built at the Sanford Underground Research Facility (SURF). The LZ dark matter experiment is designed to achieve sensitivity to a WIMP-nucleon spin-independent cross section of three times ten to the negative forty-eighth square centimeters.
△ Less
Submitted 27 March, 2017;
originally announced March 2017.
-
Quenching Measurements and Modeling of a Boron-Loaded Organic Liquid Scintillator
Authors:
Shawn Westerdale,
**gke Xu,
Emily Shields,
Francis Froborg,
Frank Calaprice,
Thomas Alexander,
Ani Aprahamian,
Henning O. Back,
Clark Casarella,
Xiao Fang,
Yogesh K. Gupta,
Edward Lamere,
Qian Liu,
Stephanie Lyons,
Mallory Smith,
Wanpeng Tan
Abstract:
Organic liquid scintillators are used in a wide variety of applications in experimental nuclear and particle physics. Boron-loaded scintillators are particularly useful for detecting neutron captures, due to the high thermal neutron capture cross section of $^{10}$B. These scintillators are commonly used in neutron detectors, including the DarkSide-50 neutron veto, where the neutron may produce a…
▽ More
Organic liquid scintillators are used in a wide variety of applications in experimental nuclear and particle physics. Boron-loaded scintillators are particularly useful for detecting neutron captures, due to the high thermal neutron capture cross section of $^{10}$B. These scintillators are commonly used in neutron detectors, including the DarkSide-50 neutron veto, where the neutron may produce a signal when it scatters off protons in the scintillator or when it captures on $^{10}$B. Reconstructing the energy of these recoils is complicated by scintillation quenching. Understanding how nuclear recoils are quenched in these scintillators is an important and difficult problem. In this article, we present a set of measurements of neutron-induced proton recoils in a boron-loaded organic liquid scintillator at recoil energies ranging from 57--467 keV, and we compare these measurements to predictions from different quenching models. We find that a modified Birks' model whose denominator is quadratic in $dE/dx$ best describes the measurements, with $χ^2$/NDF$=1.6$. This result will help model nuclear recoil scintillation in similar detectors and can be used to improve their neutron tagging efficiency.
△ Less
Submitted 16 July, 2017; v1 submitted 18 March, 2017;
originally announced March 2017.
-
Seasonal Modulation of the $^7$Be Solar Neutrino Rate in Borexino
Authors:
M. Agostini,
K. Altenmuller,
S. Appel,
V. Atroshchenko,
D. Basilico,
G. Bellini,
J. Benziger,
D. Bick,
G. Bonfini,
L. Borodikhina,
D. Bravo,
B. Caccianiga,
F. Calaprice,
A. Caminata,
S. Caprioli,
M. Carlini,
P. Cavalcante,
A. Chepurnov,
K. Choi,
D. D'Angelo,
S. Davini,
A. Derbin,
X. F. Ding,
L. Di Noto,
I. Drachnev
, et al. (77 additional authors not shown)
Abstract:
We detected the seasonal modulation of the $^7$Be neutrino interaction rate with the Borexino detector at the Laboratori Nazionali del Gran Sasso in Italy. The period, amplitude, and phase of the observed time evolution of the signal are consistent with its solar origin, and the absence of an annual modulation is rejected at 99.99\% C.L. The data are analyzed using three methods: the sinusoidal fi…
▽ More
We detected the seasonal modulation of the $^7$Be neutrino interaction rate with the Borexino detector at the Laboratori Nazionali del Gran Sasso in Italy. The period, amplitude, and phase of the observed time evolution of the signal are consistent with its solar origin, and the absence of an annual modulation is rejected at 99.99\% C.L. The data are analyzed using three methods: the sinusoidal fit, the Lomb-Scargle and the Empirical Mode Decomposition techniques, which all yield results in excellent agreement.
△ Less
Submitted 24 May, 2017; v1 submitted 27 January, 2017;
originally announced January 2017.
-
SABRE: WIMP modulation detection in the northern and southern hemisphere
Authors:
Francis Froborg
Abstract:
Measuring an annual modulation in a direct Dark Matter detection experiment is not only a proof of the existence of WIMPs but can also tell us more about their interaction with standard matter and maybe even their density and velocity in the halo. Such a modulation has been measured by the DAMA/LIBRA experiment in NaI(Tl) crystals. However, the interpretation as WIMP signal is controversial due to…
▽ More
Measuring an annual modulation in a direct Dark Matter detection experiment is not only a proof of the existence of WIMPs but can also tell us more about their interaction with standard matter and maybe even their density and velocity in the halo. Such a modulation has been measured by the DAMA/LIBRA experiment in NaI(Tl) crystals. However, the interpretation as WIMP signal is controversial due to contradicting results by other experiments. The SABRE experiment aims to shed light on this controversy by detecting the annual modulation in the same target material as DAMA with twin detectors at LNGS in Italy and at SUPL in Australia. The two locations in the northern and southern hemisphere allow to verify if other seasonal effects or the site have an influence on the measurement, thus reducing systematic effects. This paper will give an overview on the experimental design, the current status of the proof of principle phase mainly devoted to high-purity crystal growing, and an outlook on future plans.
△ Less
Submitted 20 January, 2016;
originally announced January 2016.
-
Scintillation efficiency measurement of Na recoils in NaI(Tl) below the DAMA/LIBRA energy threshold
Authors:
**gke Xu,
Emily Shields,
Frank Calaprice,
Shawn Westerdale,
Francis Froborg,
Burkhant Suerfu,
Thomas Alexander,
Ani Aprahamian,
Henning O. Back,
Clark Casarella,
Xiao Fang,
Yogesh K. Gupta,
Aldo Ianni,
Edward Lamere,
W. Hugh Lippincott,
Qian Liu,
Stephanie Lyons,
Kevin Siegl,
Mallory Smith,
Wanpeng Tan,
Bryant Vande Kolk
Abstract:
The dark matter interpretation of the DAMA modulation signal depends on the NaI(Tl) scintillation efficiency of nuclear recoils. Previous measurements for Na recoils have large discrepancies, especially in the DAMA/LIBRA modulation energy region. We report a quenching effect measurement of Na recoils in NaI(Tl) from 3keV$_{\text{nr}}$ to 52keV$_{\text{nr}}$, covering the whole DAMA/LIBRA energy re…
▽ More
The dark matter interpretation of the DAMA modulation signal depends on the NaI(Tl) scintillation efficiency of nuclear recoils. Previous measurements for Na recoils have large discrepancies, especially in the DAMA/LIBRA modulation energy region. We report a quenching effect measurement of Na recoils in NaI(Tl) from 3keV$_{\text{nr}}$ to 52keV$_{\text{nr}}$, covering the whole DAMA/LIBRA energy region for light WIMP interpretations. By using a low-energy, pulsed neutron beam, a double time-of-flight technique, and pulse-shape discrimination methods, we obtained the most accurate measurement of this kind for NaI(Tl) to date. The results differ significantly from the DAMA reported values at low energies, but fall between the other previous measurements. We present the implications of the new quenching results for the dark matter interpretation of the DAMA modulation signal.
△ Less
Submitted 24 March, 2015;
originally announced March 2015.
-
Monte Carlo Studies and Optimization for the Calibration System of the GERDA Experiment
Authors:
Laura Baudis,
Alfredo D. Ferella,
Francis Froborg,
Michal Tarka
Abstract:
The GERmanium Detector Array, GERDA, searches for neutrinoless double beta decay in Ge-76 using bare high-purity germanium detectors submerged in liquid argon. For the calibration of these detectors gamma emitting sources have to be lowered from their parking position on top of the cryostat over more than five meters down to the germanium crystals. With the help of Monte Carlo simulations, the rel…
▽ More
The GERmanium Detector Array, GERDA, searches for neutrinoless double beta decay in Ge-76 using bare high-purity germanium detectors submerged in liquid argon. For the calibration of these detectors gamma emitting sources have to be lowered from their parking position on top of the cryostat over more than five meters down to the germanium crystals. With the help of Monte Carlo simulations, the relevant parameters of the calibration system were determined. It was found that three Th-228 sources with an activity of 20 kBq each at two different vertical positions will be necessary to reach sufficient statistics in all detectors in less than four hours of calibration time. These sources will contribute to the background of the experiment with a total of (1.07 +/- 0.04(stat) +0.13 -0.19(sys)) 10^{-4} cts/(keV kg yr) when shielded from below with 6 cm of tantalum in the parking position.
△ Less
Submitted 12 August, 2013; v1 submitted 26 March, 2013;
originally announced March 2013.
-
The GERDA experiment for the search of 0νββ decay in ^{76}Ge
Authors:
GERDA Collaboration,
K. -H. Ackermann,
M. Agostini,
M. Allardt,
M. Altmann,
E. Andreotti,
A. M. Bakalyarov,
M. Balata,
I. Barabanov,
M. Barnabe Heider,
N. Barros,
L. Baudis,
C. Bauer,
N. Becerici-Schmidt,
E. Bellotti,
S. Belogurov,
S. T. Belyaev,
G. Benato,
A. Bettini,
L. Bezrukov,
T. Bode,
V. Brudanin,
R. Brugnera,
D. Budjas,
A. Caldwell
, et al. (114 additional authors not shown)
Abstract:
The GERDA collaboration is performing a search for neutrinoless double beta decay of ^{76}Ge with the eponymous detector. The experiment has been installed and commissioned at the Laboratori Nazionali del Gran Sasso and has started operation in November 2011. The design, construction and first operational results are described, along with detailed information from the R&D phase.
The GERDA collaboration is performing a search for neutrinoless double beta decay of ^{76}Ge with the eponymous detector. The experiment has been installed and commissioned at the Laboratori Nazionali del Gran Sasso and has started operation in November 2011. The design, construction and first operational results are described, along with detailed information from the R&D phase.
△ Less
Submitted 17 December, 2012;
originally announced December 2012.
