-
Highly efficient compact acousto-optic modulator based on a hybrid-lattice hollow core fiber
Authors:
Ricardo E. da Silva,
Jonas H. Osório,
David J. Webb,
Frédéric Gérôme,
Fetah Benabid,
Marcos A. R. Franco,
Cristiano M. B. Cordeiro
Abstract:
We demonstrate the acousto-optic modulation of a hybrid-lattice hollow core fiber (HL-HCF) for the first time. For many years, optical fibers with reduced diameters have been the main solution to increase the interaction of acoustic and optical waves. However, the high drive voltages and large modulator components still employed drastically affect the efficiency and miniaturization of these device…
▽ More
We demonstrate the acousto-optic modulation of a hybrid-lattice hollow core fiber (HL-HCF) for the first time. For many years, optical fibers with reduced diameters have been the main solution to increase the interaction of acoustic and optical waves. However, the high drive voltages and large modulator components still employed drastically affect the efficiency and miniaturization of these devices. Here, we experimentally show that combining Kagomé and tubular lattices in HL-HCFs allows for enhancing the amplification of the acoustic waves and the modulation of the guided optical modes thus providing high modulation efficiency even when using a fiber with a 240 um diameter. To the best of our knowledge, the measured HL-HCF's modulation efficiency (1.3 dB/V) is the highest compared to devices employing reduced diameter fibers. Additionally, we demonstrate a compact acousto-optic modulator with driver dimensions smaller than the HL-HCF diameter. Overall, our results show a promising alternative to solve the compromise of speed, efficiency, and compactness for integration with microscale all-fiber photonic devices.
△ Less
Submitted 2 May, 2024;
originally announced May 2024.
-
Highly efficient interaction of a tubular-lattice hollow-core fiber and flexural acoustic waves: design, characterization and analysis
Authors:
Ricardo E. da Silva,
Jonas H. Osório,
Gabriel L. Rodrigues,
David J. Webb,
Frédéric Gérôme,
Fetah Benabid,
Cristiano M. B. Cordeiro,
Marcos A. R. Franco
Abstract:
The modulation efficiency of a tubular-lattice hollow-core fiber (HCF) by means of flexural acoustic waves is investigated in detail for the first time. The main acousto-optic properties of the HCF are evaluated employing 2D and 3D models based on the finite element method. The induced coupling of the fundamental and first higher-order modes is simulated in the wavelength range from 743 to 1355 nm…
▽ More
The modulation efficiency of a tubular-lattice hollow-core fiber (HCF) by means of flexural acoustic waves is investigated in detail for the first time. The main acousto-optic properties of the HCF are evaluated employing 2D and 3D models based on the finite element method. The induced coupling of the fundamental and first higher-order modes is simulated in the wavelength range from 743 to 1355 nm. Significant acoustic (amplitude, period, strain, energy) and optical parameters (effective index, beat length, birefringence, coupling coefficient) are analyzed. The simulations are compared to experimental results, indicating higher modulation performance in HCFs compared to standard optical fibers. In addition, useful insights into the design and fabrication of all-fiber acousto-optic devices based on HCFs are provided, enabling potential application in tunable spectral filters and mode-locked fiber lasers.
△ Less
Submitted 24 February, 2024;
originally announced February 2024.
-
All-fiber broadband spectral acousto-optic modulation of a tubular-lattice hollow-core optical fiber
Authors:
Ricardo E. da Silva,
Jonas H. Osório,
Gabriel L. Rodrigues,
David J. Webb,
Frédéric Gérôme,
Fetah Benabid,
Cristiano M. B. Cordeiro,
Marcos A. R. Franco
Abstract:
We demonstrate a broadband acousto-optic notch filter based on a tubular-lattice hollow-core fiber for the first time. The guided optical modes are modulated by acoustically induced dynamic long-period gratings along the fiber. The device is fabricated employing a short interaction length (7.7 cm) and low drive voltages (10 V). Modulated spectral bands with 20 nm half-width and maximum depths grea…
▽ More
We demonstrate a broadband acousto-optic notch filter based on a tubular-lattice hollow-core fiber for the first time. The guided optical modes are modulated by acoustically induced dynamic long-period gratings along the fiber. The device is fabricated employing a short interaction length (7.7 cm) and low drive voltages (10 V). Modulated spectral bands with 20 nm half-width and maximum depths greater than 60 % are achieved. The resonant notch wavelength is tuned from 743 to 1355 nm (612 nm span) by changing the frequency of the electrical signal. The results indicate a broader tuning range compared to previous studies using standard and hollow-core fibers. It further reveals unique properties for reconfigurable spectral filters and fiber lasers, pointing to the fast switching and highly efficient modulation of all-fiber photonic devices.
△ Less
Submitted 13 November, 2023;
originally announced November 2023.
-
Combining X-ray Nano-CT and XANES Techniques for 3D Operando Monitoring of Lithiation Spatial Composition evolution in NMC Electrode
Authors:
Tuan-Tu Nguyen,
Jiahui Xu,
Zeliang Su,
Vincent De Andrade,
Alejandro A. Franco,
Bruno Delobel,
Charles Delacourt,
Arnaud Demortière
Abstract:
In this study, we present a well-defined methodology for conducting Operando X-ray absorption near-edge structure spectroscopy (XANES) in conjunction with transmission X-ray nano computed tomography (TXM-nanoCT) experiments on the LiNi$_{0.5}$Mn$_{0.3}$Co$_{0.2}$O$_2$ (NMC) cathode electrode. To minimize radiation-induced damage to the sample during charge and discharge cycles and to gain a compre…
▽ More
In this study, we present a well-defined methodology for conducting Operando X-ray absorption near-edge structure spectroscopy (XANES) in conjunction with transmission X-ray nano computed tomography (TXM-nanoCT) experiments on the LiNi$_{0.5}$Mn$_{0.3}$Co$_{0.2}$O$_2$ (NMC) cathode electrode. To minimize radiation-induced damage to the sample during charge and discharge cycles and to gain a comprehensive 3D perspective of the (de)lithiation process of the active material, we propose a novel approach that relies on employing only three energy levels, strategically positioned at pre-edge, edge, and post-edge. By adopting this technique, we successfully track the various (de)lithiation states within the three-dimensional space during partial cycling. Furthermore, we are able to extract the nanoscale lithium distribution within individual secondary particles. Our observations reveal the formation of a core-shell structure during lithiation and we also identify that not all surface areas of the particles exhibit activity during the process. Notably, lithium intercalation exhibits a distinct preference, leading to non-uniform lithiation degrees across different electrode locations. The proposed methodology is not limited to the NMC cathode electrode but can be extended to study realistic dedicated electrodes with high active material (AM) density, facilitating exploration and quantification of heterogeneities and inhomogeneous lithiation within such electrodes. This multi-scale insight into the (de)lithiation process and lithiation heterogeneities within the electrodes is expected to provide valuable knowledge for optimizing electrode design and ultimately enhancing electrode performance in the context of material science and battery materials research.
△ Less
Submitted 9 August, 2023; v1 submitted 17 July, 2023;
originally announced July 2023.
-
Computational Model for Predicting Particle Fracture During Electrode Calendering
Authors:
Jiahui Xu,
Brayan Paredes-Goyes,
Zeliang Su,
Mario Scheel,
Timm Weitkamp,
Arnaud Demortiere,
Alejandro A. Franco
Abstract:
In the context of calling for low carbon emissions, lithium-ion batteries (LIBs) have been widely concerned as a power source for electric vehicles, so the fundamental science behind their manufacturing has attracted much attention in recent years. Calendering is an important step of the LIB electrode manufacturing process, and the changes it brings to the electrode microstructure and mechanical p…
▽ More
In the context of calling for low carbon emissions, lithium-ion batteries (LIBs) have been widely concerned as a power source for electric vehicles, so the fundamental science behind their manufacturing has attracted much attention in recent years. Calendering is an important step of the LIB electrode manufacturing process, and the changes it brings to the electrode microstructure and mechanical properties are worth studying. In this work, we reported the observed cracking of active material (AM) particles due to calendering pressure under ex situ nano-X-ray tomography experiments. We developed a 3D-resolved discrete element method (DEM) model with bonded connections to physically mimic the calendering process using real AM particle shapes derived from the tomography experiments. The DEM model can well predict the change of the morphology of the dry electrode under pressure, and the changes of the applied pressure and porosity are consistent with the experimental values. At the same time, the model is able to simulate the secondary AM particles cracking by the fracture of the bond under force. Our model is the first of its kind being able to predict the fracture of the secondary particles along the calendering process. This work provides a tool for guidance in the manufacturing of optimized LIB electrodes.
△ Less
Submitted 3 June, 2023;
originally announced June 2023.
-
Binder-free CNT cathodes for Li-O$_2$ batteries with more than one life
Authors:
Zeliang Su,
Israel Temprano,
Nicolas Folastre,
Victor Vanpeene,
Julie Villanova,
Gregory Gachot,
Elena Shevchenko,
Clare P. Grey,
Alejandro A. Franco,
Arnaud Demortiere
Abstract:
Li-O$_2$ batteries (LOB) performance degradation ultimately occurs through the accumulation of discharge products and irreversible clogging of the porous electrode during the cycling. Electrode binder degradation in the presence of reduced oxygen species can result in additional coating of the conductive surface, exacerbating capacity fading. Herein, we establish a facile method to fabricate free-…
▽ More
Li-O$_2$ batteries (LOB) performance degradation ultimately occurs through the accumulation of discharge products and irreversible clogging of the porous electrode during the cycling. Electrode binder degradation in the presence of reduced oxygen species can result in additional coating of the conductive surface, exacerbating capacity fading. Herein, we establish a facile method to fabricate free-standing, binder-free electrodes for LOBs in which multi-wall carbon nanotubes (MWCNT) form cross-linked networks exhibiting high porosity, conductivity, and flexibility. These electrodes demonstrate high reproducibility upon cycling in LOBs. After cell death, efficient and inexpensive methods to wash away the accumulated discharge products are demonstrated, as reconditioning method. The second life usage of these electrodes is validated, without noticeable loss of performance. These findings aim to assist in the development of greener high energy density batteries while reducing manufacturing and recycling costs.
△ Less
Submitted 15 February, 2023;
originally announced February 2023.
-
Hollow-core fiber-based speckle displacement sensor
Authors:
Jonas H. Osório,
Thiago D. Cabral,
Eric Fujiwara,
Marcos A. R. Franco,
Foued Amrani,
Frédéric Delahaye,
Frédéric Gérôme,
Fetah Benabid,
Cristiano M. B. Cordeiro
Abstract:
The research enterprise towards achieving high-performance hollow-core photonic crystal fibers has led to impressive advancements in the latest years. Indeed, using this family of fibers becomes nowadays an overarching strategy for building a multitude of optical systems ranging from beam delivery devices to optical sources and sensors. In most applications, an effective single-mode operation is d…
▽ More
The research enterprise towards achieving high-performance hollow-core photonic crystal fibers has led to impressive advancements in the latest years. Indeed, using this family of fibers becomes nowadays an overarching strategy for building a multitude of optical systems ranging from beam delivery devices to optical sources and sensors. In most applications, an effective single-mode operation is desired and, as such, the fiber microstructure or the light launching setups are typically designed for achieving such a behavior. Alternatively, one can identify the use of large-core multimode hollow-core fibers as a promising avenue for the development of new photonic devices. Thus, in this manuscript, we propose and demonstrate the utilization of a large-core tubular-lattice fiber for accomplishing a speckle-based displacement sensor, which has been built up by inserting and suitably dislocating a single-mode fiber inside the void core of the hollow fiber. The work reported herein encompasses both simulation and experimental studies on the evolution of the multimode intensity distributions within the device as well as the demonstration of a displacement sensor with an estimated resolution of 0.7 μm. We understand that this investigation identifies a new opportunity for the employment of large-core hollow fibers within the sensing framework hence widening the gamut of applications of this family of fibers.
△ Less
Submitted 18 November, 2022;
originally announced November 2022.
-
Black-body radiation induced photodissociation and population redistribution of weakly bound states in H$_2^+$
Authors:
A. D. Ochoa Franco,
M. Beyer
Abstract:
Molecular hydrogen ions in weakly bound states close to the first dissociation threshold are attractive quantum sensors for measuring the proton-to-electron mass ratio and hyperfine-induced ortho-para mixing. The experimental accuracy of previous spectroscopic studies relying on fast ion beams could be improved by using state-of-the-art ion trap setups. With the electric dipole moment vanishing in…
▽ More
Molecular hydrogen ions in weakly bound states close to the first dissociation threshold are attractive quantum sensors for measuring the proton-to-electron mass ratio and hyperfine-induced ortho-para mixing. The experimental accuracy of previous spectroscopic studies relying on fast ion beams could be improved by using state-of-the-art ion trap setups. With the electric dipole moment vanishing in H$_2^+$ and preventing fast spontaneous emission, radiative lifetimes of the order of weeks are found. We include the effect of black-body radiation that can lead to photodissociation and rovibronic state redistribution to obtain effective lifetimes for trapped ion experiments. Rate coefficients for bound-bound and bound-continuum processes were calculated using adiabatic nuclear wave functions and nonadiabatic energies, including relativistic and radiative corrections. Effective lifetimes for the weakly bound states were obtained by solving a rate equation model and lifetimes in the range of 4 to 523~ms and $>$215~ms were found at room temperature and liquid nitrogen temperature, respectively. Black-body induced photodissociation was identified as the lifetime-limiting effect, which guarantees the purity of state-selectively generated molecular ion ensembles. The role of hyperfine-induced $g/u$-mixing, which allows pure rovibrational transitions, was found to be negligible.
△ Less
Submitted 22 September, 2022;
originally announced September 2022.
-
An Experimentally-Validated 3D Electrochemical Model Revealing Electrode Manufacturing Parameters Effects on Battery Performance
Authors:
Chaoyue Liu,
Teo Lombardo,
Jiahui Xu,
Alain C. Ngandjong,
Alejandro A. Franco
Abstract:
Electrode manufacturing is at the core of the lithium ion battery (LIB) fabrication process. The electrode microstructure and the electrochemical performance are determined by the adopted manufacturing parameters. However, in view of the strong interdependencies between these parameters, evaluating their influence on the performance is not a trivial task. In this work we present an experimentally…
▽ More
Electrode manufacturing is at the core of the lithium ion battery (LIB) fabrication process. The electrode microstructure and the electrochemical performance are determined by the adopted manufacturing parameters. However, in view of the strong interdependencies between these parameters, evaluating their influence on the performance is not a trivial task. In this work we present an experimentally validated 3D-resolved electrochemical model of a NMC111-based electrode which reveals how slurry formulation and calendering degree affect the electrode performance. A series of electrodes with different formulations and calendering degrees were fabricated at the experimental level. Corresponding three-dimensional manufacturing models were built based on the same experimental manufacturing parameters to generate the digital counterparts of the experimental electrodes that were then used in the electrochemical model. The results of simulations and experiments were compared individually. Among the manufacturing parameters analyzed, we found that the major factors linking manufacturing parameters and electrode performance are the carbon and binder domain (CBD) distribution within the electrode volume, and the electrostatic potential difference between the electrode and the current collector. A well-connected electronic conductive network throughout the electrode is vital for ensuring full utilization of active material, and it was found that increasing calendering degree is effective in reducing interfacial impedance. This work uncovers, based on a dual modeling/experimental approach, the essence of how electrode manufacturing process takes effect on electrode performance by influencing its microstructure.
△ Less
Submitted 12 June, 2022;
originally announced June 2022.
-
Lithium Ion Battery Electrode Manufacturing Model Accounting for 3D Realistic Shapes of Active Material Particles
Authors:
Jiahui Xu,
Alain C. Ngandjong,
Chaoyue Liu,
Franco M. Zanotto,
Oier Arcelus,
Arnaud Demortiere,
Alejandro A. Franco
Abstract:
The demand for lithium ion batteries (LIBs) on the market has gradually risen, with production increasing every year. To meet industrial needs, the development of digital twins designed to optimize LIB manufacturing processes is essential. Here, by using LiNi0.33Co0.33Mn0.33O2 (NMC111) material as an example, we introduce the realistic particles shapes of the active material obtained from X-ray mi…
▽ More
The demand for lithium ion batteries (LIBs) on the market has gradually risen, with production increasing every year. To meet industrial needs, the development of digital twins designed to optimize LIB manufacturing processes is essential. Here, by using LiNi0.33Co0.33Mn0.33O2 (NMC111) material as an example, we introduce the realistic particles shapes of the active material obtained from X-ray micro-computed tomography into a Coarse-Grained Molecular Dynamic physical model to simulate the slurry and its drying, and into a Discrete Element Method model able to simulate the calendering of the resulting electrode. This model enables to link the manufacturing parameters with the microstructure of the electrodes and to better observe the effect of the former on the heterogeneity of the electrodes. The results of the simulations allow us, among others, to observe the alteration of the electrode heterogeneity during the manufacturing process and the slight deformation of the secondary particles of active material.
△ Less
Submitted 8 June, 2022;
originally announced June 2022.
-
Machine Learning-Assisted Multi-Objective Optimization of Battery Manufacturing from Synthetic Data Generated by Physics-Based Simulations
Authors:
Marc Duquesnoy,
Chaoyue Liu,
Diana Zapata Dominguez,
Vishank Kumar,
Elixabete Ayerbe,
Alejandro A. Franco
Abstract:
The optimization of the electrodes manufacturing process constitutes one of the most critical steps to ensure high-quality Lithium-Ion Battery (LIB) cells, in particular for automotive applications. Because LIB electrode manufacturing is a complex process involving multiple steps and interdependent parameters, we have shown in our previous works that 3D-resolved physics-based models constitute ver…
▽ More
The optimization of the electrodes manufacturing process constitutes one of the most critical steps to ensure high-quality Lithium-Ion Battery (LIB) cells, in particular for automotive applications. Because LIB electrode manufacturing is a complex process involving multiple steps and interdependent parameters, we have shown in our previous works that 3D-resolved physics-based models constitute very useful tools to provide insights about the impact of the manufacturing process parameters on the textural and performance properties of the electrodes. However, their high-throughput application for electrode properties optimization and inverse design of manufacturing parameters is limited due to the high computational cost associated with this kind of model. In this work, we tackle this issue by proposing an innovative approach, supported by a deterministic machine learning (ML)-assisted pipeline for multi-objective optimization of LIB electrode properties and inverse design of its manufacturing process. Firstly, the pipeline generates a synthetic dataset from physics-based simulations with low discrepancy sequences, that allow to sufficiently represent the manufacturing parameters space. Secondly, the generated dataset is used to train deterministic ML models for the implementation of a fast multi-objective optimization, to identify an optimal electrode and the manufacturing parameters to adopt in order to fabricate it. Lastly, this electrode was successfully fabricated experimentally, proving that our modeling pipeline prediction is physical-relevant. Here, we demonstrate our pipeline for the simultaneous minimization of the electrode tortuosity factor and maximization of the effective electronic conductivity, the active surface area, and the density, all being parameters that affect the Li$^+$ (de-)intercalation kinetics, ionic, and electronic transport properties of the electrode.
△ Less
Submitted 3 May, 2022;
originally announced May 2022.
-
Functional Data-Driven Framework for Fast Forecasting of Electrode Slurry Rheology Simulated by Molecular Dynamics
Authors:
Marc Duquesnoy,
Teo Lombardo,
Fernando Caro,
Florent Haudiquez,
Alain C. Ngandjong,
Jiahui Xu,
Hassan Oularbi,
Alejandro A. Franco
Abstract:
Computational modeling of the manufacturing process of Lithium-Ion Battery (LIB) composite electrodes based on mechanistic approaches, allows predicting the influence of manufacturing parameters on electrode properties. However, ensuring that the calculated properties match well with experimental data, is typically time and resources consuming In this work, we tackled this issue by proposing a fun…
▽ More
Computational modeling of the manufacturing process of Lithium-Ion Battery (LIB) composite electrodes based on mechanistic approaches, allows predicting the influence of manufacturing parameters on electrode properties. However, ensuring that the calculated properties match well with experimental data, is typically time and resources consuming In this work, we tackled this issue by proposing a functional data-driven framework combining Functional Principal Component Analysis and K-Nearest Neighbors algorithms. This aims first to recover the early numerical values of a mechanistic electrode manufacturing simulation to predict if the observable being calculated is prone to match or not, \textit{i.e} screening step. In a second step it recovers additional numerical values of the ongoing mechanistic simulation iterations to predict the mechanistic simulation result, \textit{i.e} forecasting step. We demonstrated this approach in context of LIB manufacturing through non-equilibrium molecular dynamics (NEMD) simulations, aiming to capture the rheological behavior of electrode slurries. We discuss in full details our novel methodology and we report that the expected mechanistic simulation results can be obtained 11 times faster with respect to running the complete mechanistic simulation, while being accurate enough from an experimental point of view, with a $F1_{score}$ equals to 0.90, and a $R^2_{score}$ equals to 0.96 for the learnings validation. This paves the way towards a powerful tool to drastically reduce the utilization of computational resources while running mechanistic simulations of battery manufacturing electrodes.
△ Less
Submitted 12 January, 2022;
originally announced January 2022.
-
Angle-resolved hollow-core fiber-based curvature sensor
Authors:
William M. Guimarães,
Cristiano M. B. Cordeiro,
Marcos A. R. Franco,
Jonas H. Osório
Abstract:
We propose and theoretically study a new hollow-core fiber-based curvature sensor with the capability of detecting both bending magnitude and angle (direction). The new sensor relies on a tubular-lattice fiber that encompasses, in its microstructure, tubes with three different thicknesses. By adequately choosing the placement of the tubes within the fiber cross-section, and by exploring the spectr…
▽ More
We propose and theoretically study a new hollow-core fiber-based curvature sensor with the capability of detecting both bending magnitude and angle (direction). The new sensor relies on a tubular-lattice fiber that encompasses, in its microstructure, tubes with three different thicknesses. By adequately choosing the placement of the tubes within the fiber cross-section, and by exploring the spectral shifts of the fiber transmitted spectrum due to the curvature-induced mode field distributions' displacements, we demonstrate a multi-axis bending sensor. In the proposed sensor, curvature radii and angles are retrieved via a suitable calibration routine, which is based on conveniently adjusting empirical functions to the sensor response. Evaluation of the sensor performance for selected cases allowed to determine the curvature radii and angles with percentual errors of less than 7%. The approach proposed herein provides a promising path for the accomplishment of new curvature sensors able to resolve both the curvature magnitude and angle.
△ Less
Submitted 8 October, 2021;
originally announced October 2021.
-
Future Developments in Charged Particle Therapy: Improving Beam Delivery for Efficiency and Efficacy
Authors:
Jacinta Yap,
Andrea De Franco,
Suzie Sheehy
Abstract:
The physical and clinical benefits of charged particle therapy (CPT) are well recognised and recent developments have led to the rapid emergence of facilities, resulting in wider adoption worldwide. Nonetheless, the availability of CPT and complete exploitation of dosimetric advantages are still limited by high facility costs and technological challenges. There are extensive ongoing efforts to imp…
▽ More
The physical and clinical benefits of charged particle therapy (CPT) are well recognised and recent developments have led to the rapid emergence of facilities, resulting in wider adoption worldwide. Nonetheless, the availability of CPT and complete exploitation of dosimetric advantages are still limited by high facility costs and technological challenges. There are extensive ongoing efforts to improve upon these, which will lead to greater accessibility, superior delivery, and therefore better treatment outcomes. Several of these aspects can be addressed by developments to the beam delivery system (BDS) which determine the overall sha** and timing capabilities to provide high quality treatments. Modern delivery techniques are necessary but are limited by extended treatment times. The energy layer switching time (ELST) is a limiting constraint of the BDS and a determinant of the beam delivery time (BDT), along with the accelerator and other factors. This review evaluates the delivery process in detail, presenting the limitations and developments for the BDS and related accelerator technology, toward decreasing the BDT. As extended BDT impacts motion and has dosimetric implications for treatment, we discuss avenues to minimise the ELST and overview the clinical benefits and feasibility of a large energy acceptance BDS. These developments support the possibility of delivering advanced methodologies such as volumetric rescanning, FLASH and arc therapy and can further reduce costs given a faster delivery for a greater range of treatment indications. Further work to realise multi-ion, image guided and adaptive therapies is also discussed. In this review we examine how increased treatment efficiency and efficacy could be achieved with an improved BDS and how this could lead to faster and higher quality treatments for the future of CPT.
△ Less
Submitted 21 September, 2021;
originally announced September 2021.
-
Medipix3 proton and carbon ion measurements across full energy ranges and at clinical flux rates in MedAustron IR1
Authors:
Navrit Johan Singh Bal,
Claus Stefan Schmitzer,
Andrea De Franco,
Sascha Enke
Abstract:
The Medipix3, a hybrid pixel detector with a silicon sensor, has been evaluated as a beam instrumentation device with proton and carbon ion measurements in the non-clinical research room (IR1) of MedAustron Ion Therapy Center. Protons energies are varied from 62.4 to 800 MeV with $10^{4}$ to $10^{8}$ protons per second im**ing on the detector surface. For carbon ions, energies are varied from 12…
▽ More
The Medipix3, a hybrid pixel detector with a silicon sensor, has been evaluated as a beam instrumentation device with proton and carbon ion measurements in the non-clinical research room (IR1) of MedAustron Ion Therapy Center. Protons energies are varied from 62.4 to 800 MeV with $10^{4}$ to $10^{8}$ protons per second im**ing on the detector surface. For carbon ions, energies are varied from 120 to 400 MeV/amu with $10^{7}$ to $10^{8}$ carbon ions per second. Measurements include simultaneous high resolution, beam profile and beam intensity with various beam parameters at up to 1000 FPS (frames per second), count rate linearity and an assessment of radiation damage after the measurement day using an x-ray tube to provide a homogeneous radiation measurement. The count rate linearity is found to be linear within the uncertainties (dominated by accelerator related sources due to special setup) for the measurements without degraders. Various frequency components are identified within the beam intensity over time firstly including 49.98 Hz with standard deviation, $σ=0.29$, secondly 30.55 Hz $σ=0.55$ and thirdly 252.51 Hz $σ=0.83$. A direct correlation between the number of zero counting and noisy pixels is observed in the measurements with the highest flux. No conclusive evidence of long term radiation damage was found as a result of these measurements over one day.
△ Less
Submitted 14 October, 2021; v1 submitted 4 August, 2021;
originally announced August 2021.
-
Bridging Nano and Micro-scale X-ray Tomography for Battery Research by Leveraging Artificial Intelligence
Authors:
Jonathan Scharf,
Mehdi Chouchane,
Donal P. Finegan,
Bingyu Lu,
Christopher Redquest,
Min-cheol Kim,
Weiliang Yao,
Alejandro A. Franco,
Dan Gostovic,
Zhao Liu,
Mark Riccio,
František Zelenka,
Jean-Marie Doux,
Ying Shirley Meng
Abstract:
X-ray Computed Tomography (X-ray CT) is a well-known non-destructive imaging technique where contrast originates from the materials' absorption coefficients. Novel battery characterization studies on increasingly challenging samples have been enabled by the rapid development of both synchrotron and laboratory-scale imaging systems as well as innovative analysis techniques. Furthermore, the recent…
▽ More
X-ray Computed Tomography (X-ray CT) is a well-known non-destructive imaging technique where contrast originates from the materials' absorption coefficients. Novel battery characterization studies on increasingly challenging samples have been enabled by the rapid development of both synchrotron and laboratory-scale imaging systems as well as innovative analysis techniques. Furthermore, the recent development of laboratory nano-scale CT (NanoCT) systems has pushed the limits of battery material imaging towards voxel sizes previously achievable only using synchrotron facilities. Such systems are now able to reach spatial resolutions down to 50 nm. Given the non-destructive nature of CT, in-situ and operando studies have emerged as powerful methods to quantify morphological parameters, such as tortuosity factor, porosity, surface area, and volume expansion during battery operation or cycling. Combined with powerful Artificial Intelligence (AI)/Machine Learning (ML) analysis techniques, extracted 3D tomograms and battery-specific morphological parameters enable the development of predictive physics-based models that can provide valuable insights for battery engineering. These models can predict the impact of the electrode microstructure on cell performances or analyze the influence of material heterogeneities on electrochemical responses. In this work, we review the increasing role of X-ray CT experimentation in the battery field, discuss the incorporation of AI/ML in analysis, and provide a perspective on how the combination of multi-scale CT imaging techniques can expand the development of predictive multiscale battery behavioral models.
△ Less
Submitted 15 July, 2021;
originally announced July 2021.
-
Commissioning of low particle flux for proton beams at MedAustron
Authors:
Felix Ulrich-Pur,
Laurids Adler,
Thomas Bergauer,
Alexander Burker,
Andrea De Franco,
Greta Guidoboni,
Albert Hirtl,
Christian Irmler,
Stefanie Kaser,
Sebastian Nowak,
Florian Pitters,
Mauro Pivi,
Dale Prokopovich,
Claus Schmitzer,
Alexander Wastl
Abstract:
MedAustron is a synchrotron-based particle therapy centre located in Wiener Neustadt, Austria. It features three irradiation rooms for particle therapy, where proton beams with energies up to 252.7 MeV and carbon ions of up to 402.8 MeV/u are available for cancer treatment. In addition to the treatment rooms, MedAustron features a unique beamline exclusively for non-clinical research (NCR). This r…
▽ More
MedAustron is a synchrotron-based particle therapy centre located in Wiener Neustadt, Austria. It features three irradiation rooms for particle therapy, where proton beams with energies up to 252.7 MeV and carbon ions of up to 402.8 MeV/u are available for cancer treatment. In addition to the treatment rooms, MedAustron features a unique beamline exclusively for non-clinical research (NCR). This research beamline is also commissioned for proton energies up to 800 MeV, while available carbon ion energies correspond to the ones available in the clinical treatment rooms. Based on the requirements for particle therapy, all irradiation rooms offer particle rates of up to 10^9 particles/s for protons and 10^7 particles/s for carbon ions. However, for research purposes, lower particle fluxes are required and were therefore commissioned for the NCR beamline. Three particle flux settings with particle rates ranging from ~2.4x10^3 particles/s to ~5.2x10^6 particles/s were established for seven proton energies below 252.7 MeV. In addition to the particle rate, the spot sizes and beam energies were measured for these settings. Furthermore, three low flux settings for 800 MeV protons with particle rates ranging from ~2x10^3 particles/s to ~1.3x10^6 particles/s were commissioned. Since the commissioned low flux settings are in a regime well below the limits of the available standard beam diagnostics, setting up the beam under these new operational conditions entirely relied on the use of external detectors. Furthermore, a beam position measurement based alignment without using the standard beam profile monitors was performed for 800 MeV protons.
△ Less
Submitted 27 May, 2021; v1 submitted 11 February, 2021;
originally announced February 2021.
-
CHAMPION: Chalmers Hierarchical Atomic, Molecular, Polymeric & Ionic Analysis Toolkit
Authors:
Rasmus Andersson,
Fabian Årén,
Alejandro A. Franco,
Patrik Johansson
Abstract:
We present CHAMPION: a software developed to automatically detect time-dependent bonds between atoms based on their dynamics, classify the local graph topology around them, and analyze the physicochemical properties of these topologies by statistical physics. In stark contrast to methodologies where bonds are detected based on static conditions such as cut-off distances, CHAMPION considers pairs o…
▽ More
We present CHAMPION: a software developed to automatically detect time-dependent bonds between atoms based on their dynamics, classify the local graph topology around them, and analyze the physicochemical properties of these topologies by statistical physics. In stark contrast to methodologies where bonds are detected based on static conditions such as cut-off distances, CHAMPION considers pairs of atoms to be bound only if they move together and act as a bound pair over time. Furthermore, the time-dependent global bond graph is possible to split into dynamically shifting connected components or subgraphs around a certain chemical motif and thereby allow the physicochemical properties of each such topology to be analyzed by statistical physics. Applicable to condensed matter and liquids in general, and electrolytes in particular, this allows both quantitative and qualitative descriptions of local structure, as well as dynamical processes such as speciation and diffusion. We present here a detailed overview of CHAMPION, including its underlying methodology, implementation and capabilities.
△ Less
Submitted 2 February, 2021;
originally announced February 2021.
-
Solitary wave fission of a large disturbance in a viscous fluid conduit
Authors:
M. D. Maiden,
N. A. Franco,
E. G. Webb,
G. A. El,
M. A. Hoefer
Abstract:
This paper presents a theoretical and experimental study of the long-standing fluid mechanics problem involving the temporal resolution of a large, localised initial disturbance into a sequence of solitary waves. This problem is of fundamental importance in a range of applications including tsunami and internal ocean wave modelling. This study is performed in the context of the viscous fluid condu…
▽ More
This paper presents a theoretical and experimental study of the long-standing fluid mechanics problem involving the temporal resolution of a large, localised initial disturbance into a sequence of solitary waves. This problem is of fundamental importance in a range of applications including tsunami and internal ocean wave modelling. This study is performed in the context of the viscous fluid conduit system-the driven, cylindrical, free interface between two miscible Stokes fluids with high viscosity contrast. Due to buoyancy induced nonlinear self-steepening balanced by stress induced interfacial dispersion, the disturbance evolves into a slowly modulated wavetrain and further, into a sequence of solitary waves. An extension of Whitham modulation theory, termed the solitary wave resolution method, is used to resolve the fission of an initial disturbance into solitary waves. The developed theory predicts the relationship between the initial disturbance's profile, the number of emergent solitary waves, and their amplitude distribution, quantifying an extension of the well-known soliton resolution conjecture from integrable systems to non-integrable systems that often provide a more accurate modelling of physical systems. The theoretical predictions for the fluid conduit system are confirmed both numerically and experimentally. The number of observed solitary waves is consistently within 1-2 waves of the prediction, and the amplitude distribution shows remarkable agreement. Universal properties of solitary wave fission in other fluid dynamics problems are identified.
△ Less
Submitted 18 August, 2019; v1 submitted 29 April, 2019;
originally announced April 2019.
-
A next-generation LHC heavy-ion experiment
Authors:
D. Adamová,
G. Aglieri Rinella,
M. Agnello,
Z. Ahammed,
D. Aleksandrov,
A. Alici,
A. Alkin,
T. Alt,
I. Altsybeev,
D. Andreou,
A. Andronic,
F. Antinori,
P. Antonioli,
H. Appelshäuser,
R. Arnaldi,
I. C. Arsene,
M. Arslandok,
R. Averbeck,
M. D. Azmi,
X. Bai,
R. Bailhache,
R. Bala,
L. Barioglio,
G. G. Barnaföldi,
L. S. Barnby
, et al. (374 additional authors not shown)
Abstract:
The present document discusses plans for a compact, next-generation multi-purpose detector at the LHC as a follow-up to the present ALICE experiment. The aim is to build a nearly massless barrel detector consisting of truly cylindrical layers based on curved wafer-scale ultra-thin silicon sensors with MAPS technology, featuring an unprecedented low material budget of 0.05% X$_0$ per layer, with th…
▽ More
The present document discusses plans for a compact, next-generation multi-purpose detector at the LHC as a follow-up to the present ALICE experiment. The aim is to build a nearly massless barrel detector consisting of truly cylindrical layers based on curved wafer-scale ultra-thin silicon sensors with MAPS technology, featuring an unprecedented low material budget of 0.05% X$_0$ per layer, with the innermost layers possibly positioned inside the beam pipe. In addition to superior tracking and vertexing capabilities over a wide momentum range down to a few tens of MeV/$c$, the detector will provide particle identification via time-of-flight determination with about 20~ps resolution. In addition, electron and photon identification will be performed in a separate shower detector. The proposed detector is conceived for studies of pp, pA and AA collisions at luminosities a factor of 20 to 50 times higher than possible with the upgraded ALICE detector, enabling a rich physics program ranging from measurements with electromagnetic probes at ultra-low transverse momenta to precision physics in the charm and beauty sector.
△ Less
Submitted 2 May, 2019; v1 submitted 31 January, 2019;
originally announced February 2019.
-
Optical inspection of manufactured nanohole arrays to bridge the lab-industry gap
Authors:
A. Franco,
D. Otaduy,
A. I. Barreda,
J. L. FernÁndez-Luna,
S. Merino,
F. GonzÁlez,
F. Moreno
Abstract:
Metallic nanohole arrays have shown their potential as sensing tools. Important research supported by sophisticated laboratory experiments have been recently carried out, that may help to develop practical devices to be implemented in the real life. To get this goal, the gap between industry and technology at the nanoscale level must be overcome. One of the major drawbacks is the quality inspectio…
▽ More
Metallic nanohole arrays have shown their potential as sensing tools. Important research supported by sophisticated laboratory experiments have been recently carried out, that may help to develop practical devices to be implemented in the real life. To get this goal, the gap between industry and technology at the nanoscale level must be overcome. One of the major drawbacks is the quality inspection of the manufactured nanostructured surfaces to ensure a reliable sensing. In this paper we introduce an optical method, based on the Extraordinary Optical Transmission phenomenon, for an inspection of such surfaces at industrial level. Unlike usual techniques like SEM, our method gives at the same time, a quick map of the surface homogeneity together with its local plasmonic performance. Our results show that this method is reproducible and reliable as to give a seal of identification and quality guarantee of the manufactured surface as basic element of a sensing device.
△ Less
Submitted 22 November, 2018;
originally announced November 2018.
-
Comparison of Algorithms for Baseline Correction of LIBS Spectra for Quantifying Total Carbon in Brazilian Soils
Authors:
Marco Aurélio de Menezes Franco,
Débora Marcondes Bastos Pereira Milori,
Paulino Ribeiro Villas Boas
Abstract:
LIBS (Laser-Induced Breakdown Spectroscopy) is a versatile technique for multi-element analysis, offering rapid analysis with minimal sample preparation. However, challenges persist in baseline correction due to background radiation, causing non-linear interference with emission lines. This necessitates proper baseline correction for accurate quantification of elements in LIBS spectra. Our study f…
▽ More
LIBS (Laser-Induced Breakdown Spectroscopy) is a versatile technique for multi-element analysis, offering rapid analysis with minimal sample preparation. However, challenges persist in baseline correction due to background radiation, causing non-linear interference with emission lines. This necessitates proper baseline correction for accurate quantification of elements in LIBS spectra. Our study focuses on the quantification of total carbon in soil samples, conducting a comparative analysis of filters and methods for noise removal and baseline correction in LIBS spectra. We exhaustively tested all combinations of filters and methods, optimizing their parameters to establish the strongest correlation between corrected spectra and carbon content in a training sample set. We then evaluated these combinations using optimized parameters on a separate test sample set. Through rigorous evaluation, we found that the combination of the Savitzky-Golay filter and the 4S Peak Filling method achieved the most effective baseline correction. This combination demonstrated a Pearson's correlation coefficient of 0.93 and a root mean square error of 0.21. Notably, it outperformed a linear regression model based solely on the carbon emission line at 193.04 nm, which yielded a correlation of 0.91 with a root mean square error of 0.26. Our proposed procedure presents a novel approach for baseline correction in LIBS spectra, opening new possibilities for the development of multivariate methods utilizing specific spectral ranges.
△ Less
Submitted 14 May, 2023; v1 submitted 19 April, 2018;
originally announced May 2018.
-
Solitonic dispersive hydrodynamics: theory and observation
Authors:
Michelle D. Maiden,
Dalton V. Anderson,
Nevil A. Franco,
Gennady A. El,
Mark A. Hoefer
Abstract:
Ubiquitous nonlinear waves in dispersive media include localized solitons and extended hydrodynamic states such as dispersive shock waves. Despite their physical prominence and the development of thorough theoretical and experimental investigations of each separately, experiments and a unified theory of solitons and dispersive hydrodynamics are lacking. Here, a general soliton-mean field theory is…
▽ More
Ubiquitous nonlinear waves in dispersive media include localized solitons and extended hydrodynamic states such as dispersive shock waves. Despite their physical prominence and the development of thorough theoretical and experimental investigations of each separately, experiments and a unified theory of solitons and dispersive hydrodynamics are lacking. Here, a general soliton-mean field theory is introduced and used to describe the propagation of solitons in macroscopic hydrodynamic flows. Two universal adiabatic invariants of motion are identified that predict trap** or transmission of solitons by hydrodynamic states. The result of solitons incident upon smooth expansion waves or compressive, rapidly oscillating dispersive shock waves is the same, an effect termed hydrodynamic reciprocity. Experiments on viscous fluid conduits quantitatively confirm the soliton-mean field theory with broader implications for nonlinear optics, superfluids, geophysical fluids, and other dispersive hydrodynamic media.
△ Less
Submitted 28 February, 2018; v1 submitted 5 November, 2017;
originally announced November 2017.
-
A simple mathematical approach to optimize the structure of reaction-diffusion physicochemical systems
Authors:
Jean-Paul Chehab,
Alejandro A. Franco,
Youcef Mammeri
Abstract:
The calculation of optimal structures in reaction-diffusion models is of great importance in many physicochemical systems. We propose here a simple method to monitor the number of interphases for long times by using a boundary flux condition as a control. We consider as an illustration a 1-D Allen-Cahn equation with Neumann boundary conditions. Numerical examples are given and perspectives for the…
▽ More
The calculation of optimal structures in reaction-diffusion models is of great importance in many physicochemical systems. We propose here a simple method to monitor the number of interphases for long times by using a boundary flux condition as a control. We consider as an illustration a 1-D Allen-Cahn equation with Neumann boundary conditions. Numerical examples are given and perspectives for the application of this approach to electrochemical systems are discussed.
△ Less
Submitted 5 March, 2014; v1 submitted 31 December, 2013;
originally announced January 2014.
-
Computer simulations reveal complex distribution of haemodynamic forces in a mouse retina model of angiogenesis
Authors:
Miguel O. Bernabeu,
Martin Jones,
Jens H. Nielsen,
Timm Krüger,
Rupert W. Nash,
Derek Groen,
Sebastian Schmieschek,
James Hetherington,
Holger Gerhardt,
Claudio A. Franco,
Peter V. Coveney
Abstract:
There is currently limited understanding of the role played by haemodynamic forces on the processes governing vascular development. One of many obstacles to be overcome is being able to measure those forces, at the required resolution level, on vessels only a few micrometres thick. In the current paper, we present an in silico method for the computation of the haemodynamic forces experienced by mu…
▽ More
There is currently limited understanding of the role played by haemodynamic forces on the processes governing vascular development. One of many obstacles to be overcome is being able to measure those forces, at the required resolution level, on vessels only a few micrometres thick. In the current paper, we present an in silico method for the computation of the haemodynamic forces experienced by murine retinal vasculature (a widely used vascular development animal model) beyond what is measurable experimentally. Our results show that it is possible to reconstruct high-resolution three-dimensional geometrical models directly from samples of retinal vasculature and that the lattice-Boltzmann algorithm can be used to obtain accurate estimates of the haemodynamics in these domains. We generate flow models from samples obtained at postnatal days (P) 5 and 6. Our simulations show important differences between the flow patterns recovered in both cases, including observations of regression occurring in areas where wall shear stress gradients exist. We propose two possible mechanisms to account for the observed increase in velocity and wall shear stress between P5 and P6: i) the measured reduction in typical vessel diameter between both time points, ii) the reduction in network density triggered by the pruning process. The methodology developed herein is applicable to other biomedical domains where microvasculature can be imaged but experimental flow measurements are unavailable or difficult to obtain.
△ Less
Submitted 15 July, 2014; v1 submitted 7 November, 2013;
originally announced November 2013.
-
Thermomagnetic instability of a rotating magnetized plasma disk
Authors:
Giovanni Montani,
Riccardo Benini,
Nakia Carlevaro,
Alessio Franco
Abstract:
We analyze the stability of a thin plasma disk which is rotating around a compact astrophysical object and is embedded in the strong magnetic field of such a source. The aim of this study is the determination of a new type of unstable modes, able to replace the magneto-rotational instability profile for low beta-values and for sufficiently small scales of the perturbations, where it fails. In part…
▽ More
We analyze the stability of a thin plasma disk which is rotating around a compact astrophysical object and is embedded in the strong magnetic field of such a source. The aim of this study is the determination of a new type of unstable modes, able to replace the magneto-rotational instability profile for low beta-values and for sufficiently small scales of the perturbations, where it fails. In particular, we consider the magneto-hydrodynamical scheme including a non-zero Nernst coefficient, corresponding to first-order collisional effects. As a result, modes with imaginary frequency lead to an instability regime when the magnetic tension vanishes. Finally, we show that, even in the presence of resistive effects, it remains a good candidate to ensure the onset of a turbulent behavior in the absence of the magneto-rotational instability.
△ Less
Submitted 12 December, 2013; v1 submitted 13 September, 2013;
originally announced September 2013.
-
The Geometry of the Vapor Layer Under a Leidenfrost Drop
Authors:
J. C. Burton,
A. L. Sharpe,
R. C. A. van der Veen,
A. Franco,
S. R. Nagel
Abstract:
In the Leidenfrost effect, liquid drops deposited on a hot surface levitate on a thin vapor cushion fed by evaporation of the liquid. This vapor layer forms a concave depression in the drop interface. Using laser-light interference coupled to high-speed imaging, we measured the radius, curvature, and height of the vapor pocket, as well as non-axisymmetric fluctuations of the interface for water dr…
▽ More
In the Leidenfrost effect, liquid drops deposited on a hot surface levitate on a thin vapor cushion fed by evaporation of the liquid. This vapor layer forms a concave depression in the drop interface. Using laser-light interference coupled to high-speed imaging, we measured the radius, curvature, and height of the vapor pocket, as well as non-axisymmetric fluctuations of the interface for water drops at different temperatures. The geometry of the vapor pocket depends primarily on the drop size and not on the substrate temperature.
△ Less
Submitted 20 June, 2012; v1 submitted 9 February, 2012;
originally announced February 2012.
-
Effect of lamellar nanostructures on the second harmonic generation of polymethylmethacrylate films doped with 4-(4-nitrophenylazo)aniline chromophores
Authors:
Alfredo Franco,
Laura Romero-Miranda,
Guadalupe Valverde-Aguilar,
Jorge García-Macedo,
Giovanna Brusatin,
Massimo Guglielmi
Abstract:
The kinetics of the orientation of Disperse Orange 3 molecules embedded in amorphous and nanostructured Polymethylmethacrylate films was studied under the effect of an intense electrostatic poling field. Non-centrosymmetric chromophore distributions were obtained in Polymethylmethacrylate films by Corona poling technique. These distributions depends on the Corona poling time. The changes in the or…
▽ More
The kinetics of the orientation of Disperse Orange 3 molecules embedded in amorphous and nanostructured Polymethylmethacrylate films was studied under the effect of an intense electrostatic poling field. Non-centrosymmetric chromophore distributions were obtained in Polymethylmethacrylate films by Corona poling technique. These distributions depends on the Corona poling time. The changes in the orientation of the Disperse Orange 3 molecules were followed by in-situ transmitted Second Harmonic Generation measurements. The Second Harmonic Generation signal was recorded as function of time at several temperatures; it was fitted as function of the Corona poling time, considering matrix-chromophore interactions. The Polymethylmethacrylate films were nanostructured by the incorporation of an anionic surfactant, the Sodium Dodecyl Sulfate. The lamellar nanostructures in the films were identified by X-ray diffraction measurements.
△ Less
Submitted 18 November, 2011;
originally announced November 2011.
-
The current progress of the ALICE Ring Imaging Cherenkov Detector
Authors:
A. Braem,
G. De Cataldo,
M. Davenport,
A. Di Mauro,
A. Franco,
A. Gallas,
H. Hoedlmoser,
P. Martinengo,
E. Nappi,
G. Paic,
F. Piuz,
V. Peskov
Abstract:
Recently, the last two modules (out of seven) of the ALICE High Momentum Particle Identification detector (HMPID) were assembled and tested. The full detector, after a pre-commissioning phase, has been installed in the experimental area, inside the ALICE solenoid, at the end of September 2006. In this paper we review the status of the ALICE/HMPID project and we present a summary of the series pr…
▽ More
Recently, the last two modules (out of seven) of the ALICE High Momentum Particle Identification detector (HMPID) were assembled and tested. The full detector, after a pre-commissioning phase, has been installed in the experimental area, inside the ALICE solenoid, at the end of September 2006. In this paper we review the status of the ALICE/HMPID project and we present a summary of the series production of the CsI photo-cathodes. We describe the key features of the production procedure which ensures high quality photo-cathodes as well as the results of the quality assessment performed by means of a specially developed 2D scanner system able to produce a detailed map of the CsI photo-current over the entire photo-cathode surface.
Finally we present our recent R&D efforts toward the development of a novel generation of imaging Cherenkov detectors with the aim to identify, in heavy ions collisions, hadrons up to 30 GeV/c.
△ Less
Submitted 5 March, 2007;
originally announced March 2007.
-
Spin 1/2 Particle on a Cylinder with Radial Magnetic Field
Authors:
C. Chryssomalakos,
A. Franco,
A. Reyes-Coronado
Abstract:
We study the motion of a charged quantum particle, constrained on the surface of a cylinder, in the presence of a radial magnetic field. When the spin of the particle is neglected, the system essentially reduces to an infinite family of simple harmonic oscillators, equally spaced along the axis of the cylinder. Interestingly enough, it can be used as a quantum Fourier transformer, with convenien…
▽ More
We study the motion of a charged quantum particle, constrained on the surface of a cylinder, in the presence of a radial magnetic field. When the spin of the particle is neglected, the system essentially reduces to an infinite family of simple harmonic oscillators, equally spaced along the axis of the cylinder. Interestingly enough, it can be used as a quantum Fourier transformer, with convenient visual output. When the spin 1/2 of the particle is taken into account, a non-conventional perturbative analysis results in a recursive closed form for the corrections to the energy and the wavefunction, for all eigenstates, to all orders in the magnetic moment of the particle. A simple two-state system is also presented, the time evolution of which involves an approximate precession of the spin perpendicularly to the magnetic field. A number of plots highlight the findings while several three-dimensional animations have been made available on the web.
△ Less
Submitted 8 July, 2003; v1 submitted 9 December, 2002;
originally announced December 2002.