Showing 1–33 of 33 results for author: Favre, Y

Testbeam results of irradiated SiGe BiCMOS monolithic silicon pixel detector without internal gain layer

Authors: T. Moretti, M. Milanesio, R. Cardella, T. Kugathasan, A. Picardi, I. Semendyaev, M. Elviretti, H. Rücker, K. Nakamura, Y. Takubo, M. Togawa, F. Cadoux, R. Cardarelli, L. Cecconi, S. Débieux, Y. Favre, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, L. Iodice, R. Kotitsa, C. Magliocca, M. Nessi, A. Pizarro-Medina, J. Sabater Iglesias , et al. (5 additional authors not shown)

Abstract: Samples of the monolithic silicon pixel ASIC prototype produced in 2022 within the framework of the Horizon 2020 MONOLITH ERC Advanced project were irradiated with 70 MeV protons up to a fluence of 1 x 1016 neq/cm2, and then tested using a beam of 120 GeV/c pions. The ASIC contains a matrix of 100 μm pitch hexagonal pixels, readout out by low noise and very fast frontend electronics produced in a… ▽ More Samples of the monolithic silicon pixel ASIC prototype produced in 2022 within the framework of the Horizon 2020 MONOLITH ERC Advanced project were irradiated with 70 MeV protons up to a fluence of 1 x 1016 neq/cm2, and then tested using a beam of 120 GeV/c pions. The ASIC contains a matrix of 100 μm pitch hexagonal pixels, readout out by low noise and very fast frontend electronics produced in a 130 nm SiGe BiCMOS technology process. The dependence on the proton fluence of the efficiency and the time resolution of this prototype was measured with the frontend electronics operated at a power density between 0.13 and 0.9 W/cm2. The testbeam data show that the detection efficiency of 99.96% measured at sensor bias voltage of 200 V before irradiation becomes 96.2% after a fluence of 1 x 1016 neq/cm2. An increase of the sensor bias voltage to 300 V provides an efficiency to 99.7% at that proton fluence. The timing resolution of 20 ps measured before irradiation rises for a proton fluence of 1 x 1016 neq/cm2 to 53 and 45 ps at HV = 200 and 300 V, respectively. △ Less

Submitted 21 June, 2024; v1 submitted 19 April, 2024; originally announced April 2024.

First Measurement of the $ν_e$ and $ν_μ$ Interaction Cross Sections at the LHC with FASER's Emulsion Detector

Authors: FASER Collaboration, Roshan Mammen Abraham, John Anders, Claire Antel, Akitaka Ariga, Tomoko Ariga, Jeremy Atkinson, Florian U. Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Angela Burger, Franck Cadoux, Roberto Cardella, David W. Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Stephane Debieux, Monica D'Onofrio, Ansh Desai, Sergey Dmitrievsky, Sinead Eley, Yannick Favre, Deion Fellers , et al. (80 additional authors not shown)

Abstract: This paper presents the first results of the study of high-energy electron and muon neutrino charged-current interactions in the FASER$ν$ emulsion/tungsten detector of the FASER experiment at the LHC. A subset of the FASER$ν$ volume, which corresponds to a target mass of 128.6~kg, was exposed to neutrinos from the LHC $pp$ collisions with a centre-of-mass energy of 13.6~TeV and an integrated lumin… ▽ More This paper presents the first results of the study of high-energy electron and muon neutrino charged-current interactions in the FASER$ν$ emulsion/tungsten detector of the FASER experiment at the LHC. A subset of the FASER$ν$ volume, which corresponds to a target mass of 128.6~kg, was exposed to neutrinos from the LHC $pp$ collisions with a centre-of-mass energy of 13.6~TeV and an integrated luminosity of 9.5 fb$^{-1}$. Applying stringent selections requiring electrons with reconstructed energy above 200~GeV, four electron neutrino interaction candidate events are observed with an expected background of $0.025^{+0.015}_{-0.010}$, leading to a statistical significance of 5.2$σ$. This is the first direct observation of electron neutrino interactions at a particle collider. Eight muon neutrino interaction candidate events are also detected, with an expected background of $0.22^{+0.09}_{-0.07}$, leading to a statistical significance of 5.7$σ$. The signal events include neutrinos with energies in the TeV range, the highest-energy electron and muon neutrinos ever detected from an artificial source. The energy-independent part of the interaction cross section per nucleon is measured over an energy range of 560--1740 GeV (520--1760 GeV) for $ν_e$ ($ν_μ$) to be $(1.2_{-0.7}^{+0.8}) \times 10^{-38}~\mathrm{cm}^{2}\,\mathrm{GeV}^{-1}$ ($(0.5\pm0.2) \times 10^{-38}~\mathrm{cm}^{2}\,\mathrm{GeV}^{-1}$), consistent with Standard Model predictions. These are the first measurements of neutrino interaction cross sections in those energy ranges. △ Less

Submitted 19 March, 2024; originally announced March 2024.

Radiation Tolerance of SiGe BiCMOS Monolithic Silicon Pixel Detectors without Internal Gain Layer

Authors: M. Milanesio, L. Paolozzi, T. Moretti, R. Cardella, T. Kugathasan, F. Martinelli, A. Picardi, I. Semendyaev, S. Zambito, K. Nakamura, Y. Tabuko, M. Togawa, M. Elviretti, H. Rücker, F. Cadoux, R. Cardarelli, S. Débieux, Y. Favre, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, L. Iodice, R. Kotitsa, C. Magliocca, M. Nessi , et al. (5 additional authors not shown)

Abstract: A monolithic silicon pixel prototype produced for the MONOLITH ERC Advanced project was irradiated with 70 MeV protons up to a fluence of 1 x 10^16 1 MeV n_eq/cm^2. The ASIC contains a matrix of hexagonal pixels with 100 μm pitch, readout by low-noise and very fast SiGe HBT frontend electronics. Wafers with 50 μm thick epilayer with a resistivity of 350 Ωcm were used to produce a fully depleted se… ▽ More A monolithic silicon pixel prototype produced for the MONOLITH ERC Advanced project was irradiated with 70 MeV protons up to a fluence of 1 x 10^16 1 MeV n_eq/cm^2. The ASIC contains a matrix of hexagonal pixels with 100 μm pitch, readout by low-noise and very fast SiGe HBT frontend electronics. Wafers with 50 μm thick epilayer with a resistivity of 350 Ωcm were used to produce a fully depleted sensor. Laboratory tests conducted with a 90Sr source show that the detector works satisfactorily after irradiation. The signal-to-noise ratio is not seen to change up to fluence of 6 x 10^14 n_eq /cm^2 . The signal time jitter was estimated as the ratio between the voltage noise and the signal slope at threshold. At -35 {^\circ}C, sensor bias voltage of 200 V and frontend power consumption of 0.9 W/cm^2, the time jitter of the most-probable signal amplitude was estimated to be 21 ps for proton fluence up to 6 x 10 n_eq/cm^2 and 57 ps at 1 x 10^16 n_eq/cm^2 . Increasing the sensor bias to 250 V and the analog voltage of the preamplifier from 1.8 to 2.0 V provides a time jitter of 40 ps at 1 x 10^16 n_eq/cm^2. △ Less

Submitted 30 October, 2023; originally announced October 2023.

Comments: Submitted to JINST

20 ps Time Resolution with a Fully-Efficient Monolithic Silicon Pixel Detector without Internal Gain Layer

Authors: S. Zambito, M. Milanesio, T. Moretti, L. Paolozzi, M. Munker, R. Cardella, T. Kugathasan, F. Martinelli, A. Picardi, M. Elviretti, H. Rücker, A. Trusch, F. Cadoux, R. Cardarelli, S. Débieux, Y. Favre, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, L. Iodice, R. Kotitsa, C. Magliocca, M. Nessi, A. Pizarro-Medina, J. Sabater Iglesias , et al. (3 additional authors not shown)

Abstract: A second monolithic silicon pixel prototype was produced for the MONOLITH project. The ASIC contains a matrix of hexagonal pixels with 100 μm pitch, readout by a low-noise and very fast SiGe HBT frontend electronics. Wafers with 50 μm thick epilayer of 350 Ωcm resistivity were used to produce a fully depleted sensor. Laboratory and testbeam measurements of the analog channels present in the pixel… ▽ More A second monolithic silicon pixel prototype was produced for the MONOLITH project. The ASIC contains a matrix of hexagonal pixels with 100 μm pitch, readout by a low-noise and very fast SiGe HBT frontend electronics. Wafers with 50 μm thick epilayer of 350 Ωcm resistivity were used to produce a fully depleted sensor. Laboratory and testbeam measurements of the analog channels present in the pixel matrix show that the sensor has a 130 V wide bias-voltage operation plateau at which the efficiency is 99.8%. Although this prototype does not include an internal gain layer, the design optimised for timing of the sensor and the front-end electronics provides a time resolutions of 20 ps. △ Less

Submitted 28 January, 2023; originally announced January 2023.

Comments: 11 pages, 11 figures

Testbeam Results of the Picosecond Avalanche Detector Proof-Of-Concept Prototype

Authors: G. Iacobucci, S. Zambito, M. Milanesio, T. Moretti, J. Saidi, L. Paolozzi, M. Munker, R. Cardella, F. Martinelli, A. Picardi, H. Rücker, A. Trusch, P. Valerio, F. Cadoux, R. Cardarelli, S. Débieux, Y. Favre, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, Y. Gurimskaya, R. Kotitsa, C. Magliocca, M. Nessi, A. Pizarro-Medina , et al. (2 additional authors not shown)

Abstract: The proof-of-concept prototype of the Picosecond Avalanche Detector, a multi-PN junction monolithic silicon detector with continuous gain layer deep in the sensor depleted region, was tested with a beam of 180 GeV pions at the CERN SPS. The prototype features low noise and fast SiGe BiCMOS frontend electronics and hexagonal pixels with 100 μm pitch. At a sensor bias voltage of 125 V, the detector… ▽ More The proof-of-concept prototype of the Picosecond Avalanche Detector, a multi-PN junction monolithic silicon detector with continuous gain layer deep in the sensor depleted region, was tested with a beam of 180 GeV pions at the CERN SPS. The prototype features low noise and fast SiGe BiCMOS frontend electronics and hexagonal pixels with 100 μm pitch. At a sensor bias voltage of 125 V, the detector provides full efficiency and average time resolution of 30, 25 and 17 ps in the overall pixel area for a power consumption of 0.4, 0.9 and 2.7 W/cm^2, respectively. In this first prototype the time resolution depends significantly on the distance from the center of the pixel, varying at the highest power consumption measured between 13 ps at the center of the pixel and 25 ps in the inter-pixel region. △ Less

Submitted 23 August, 2022; originally announced August 2022.

The FASER Detector

Authors: FASER Collaboration, Henso Abreu, Elham Amin Mansour, Claire Antel, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David W. Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Olivier Crespo-Lopez, Stephane Debieux, Monica D'Onofrio, Liam Dougherty, Candan Dozen, Abdallah Ezzat, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere , et al. (72 additional authors not shown)

Abstract: FASER, the ForwArd Search ExpeRiment, is an experiment dedicated to searching for light, extremely weakly-interacting particles at CERN's Large Hadron Collider (LHC). Such particles may be produced in the very forward direction of the LHC's high-energy collisions and then decay to visible particles inside the FASER detector, which is placed 480 m downstream of the ATLAS interaction point, aligned… ▽ More FASER, the ForwArd Search ExpeRiment, is an experiment dedicated to searching for light, extremely weakly-interacting particles at CERN's Large Hadron Collider (LHC). Such particles may be produced in the very forward direction of the LHC's high-energy collisions and then decay to visible particles inside the FASER detector, which is placed 480 m downstream of the ATLAS interaction point, aligned with the beam collisions axis. FASER also includes a sub-detector, FASER$ν$, designed to detect neutrinos produced in the LHC collisions and to study their properties. In this paper, each component of the FASER detector is described in detail, as well as the installation of the experiment system and its commissioning using cosmic-rays collected in September 2021 and during the LHC pilot beam test carried out in October 2021. FASER will start taking LHC collision data in 2022, and will run throughout LHC Run 3. △ Less

Submitted 23 July, 2022; originally announced July 2022.

Comments: 92 pages, 72 Figures

Report number: CERN-FASER-2022-001

Journal ref: JINST 19 (2024) P05066

SuperFGD prototype time resolution studies

Authors: I. Alekseev, T. Arihara, V. Baranov, L. Bartoszek, L. Bernardi, A. Blondel, A. V. Boikov, M. Buizza-Avanzini, F. Cadoux, J. Capó, J. Cayo, J. Chakrani, P. S. Chong, A. Chvirova, M. Danilov, Yu. I. Davydov, A. Dergacheva, N. Dokania, D. Douqa, O. Drapier, A. Eguchi, Y. Favre, D. Fedorova, S. Fedotov, Y. Fujii , et al. (65 additional authors not shown)

Abstract: The SuperFGD will be a part of the ND280 near detector of the T2K and Hyper Kamiokande projects, that will help to reduce systematic uncertainties related with neutrino flux and cross-section modeling. The upgraded ND280 will be able to perform a full exclusive reconstruction of the final state from neutrino-nucleus interactions, including measurements of low momentum protons, pions and, for the f… ▽ More The SuperFGD will be a part of the ND280 near detector of the T2K and Hyper Kamiokande projects, that will help to reduce systematic uncertainties related with neutrino flux and cross-section modeling. The upgraded ND280 will be able to perform a full exclusive reconstruction of the final state from neutrino-nucleus interactions, including measurements of low momentum protons, pions and, for the first time, event-by event measurements of neutron kinematics. The time resolution defines the neutron energy resolution. We present the results of time resolution measurements made with the SuperFGD prototype that consists of 9216 plastic scintillator cubes (cube size is 1 cm$^3$) readout with 1728 wavelength-shifting fibers going along three orthogonal directions. We use data from the muon beam exposure at CERN. The time resolution of 0.97 ns was obtained for one readout channel after implementing the time calibration with a correction for the time-walk effect. The time resolution improves with energy deposited in a scintillator cube. Averaging two readout channels for one scintillator cube improves the time resolution to 0.68 ns which means that signals in different channels are not synchronous. Therefore the contribution from the time recording step of 2.5 ns is averaged as well. Averaging time values from N channels improves the time resolution by $\sim 1/\sqrt{N}$. Therefore a very good time resolution should be achievable for neutrons since neutron recoils hit typically several scintillator cubes and in addition produce larger amplitudes than muons. Measurements performed with a laser and a wide-bandwidth oscilloscope demonstrated that the time resolution obtained with the muon beam is not far from its expected limit. The intrinsic time resolution of one channel is 0.67 ns for signals of 56 photo-electron typical for minimum ionizing particles. △ Less

Submitted 18 January, 2023; v1 submitted 21 June, 2022; originally announced June 2022.

Comments: 12 pages, 9 figures. Revised text, results unchanged

Journal ref: JINST 18 P01012 (2023)

Picosecond Avalanche Detector -- working principle and gain measurement with a proof-of-concept prototype

Authors: L. Paolozzi, M. Munker, R. Cardella, M. Milanesio, Y. Gurimskaya, F. Martinelli, A. Picardi, H. Rücker, A. Trusch, P. Valerio, F. Cadoux, R. Cardarelli, S. Débieux, Y. Favre, C. A. Fenoglio, D. Ferrere, S. Gonzalez-Sevilla, R. Kotitsa, C. Magliocca, T. Moretti, M. Nessi, A. Pizarro Medina, J. Sabater Iglesias, J. Saidi, M. Vicente Barreto Pinto , et al. (2 additional authors not shown)

Abstract: The Picosecond Avalanche Detector is a multi-junction silicon pixel detector based on a $\mathrm{(NP)_{drift}(NP)_{gain}}$ structure, devised to enable charged-particle tracking with high spatial resolution and picosecond time-stamp capability. It uses a continuous junction deep inside the sensor volume to amplify the primary charge produced by ionizing radiation in a thin absorption layer. The si… ▽ More The Picosecond Avalanche Detector is a multi-junction silicon pixel detector based on a $\mathrm{(NP)_{drift}(NP)_{gain}}$ structure, devised to enable charged-particle tracking with high spatial resolution and picosecond time-stamp capability. It uses a continuous junction deep inside the sensor volume to amplify the primary charge produced by ionizing radiation in a thin absorption layer. The signal is then induced by the secondary charges moving inside a thicker drift region. A proof-of-concept monolithic prototype, consisting of a matrix of hexagonal pixels with 100 $μ$m pitch, has been produced using the 130 nm SiGe BiCMOS process by IHP microelectronics. Measurements on probe station and with a $^{55}$Fe X-ray source show that the prototype is functional and displays avalanche gain up to a maximum electron gain of 23. A study of the avalanche characteristics, corroborated by TCAD simulations, indicates that space-charge effects due to the large primary charge produced by the conversion of X-rays from the $^{55}$Fe source limits the effective gain. △ Less

Submitted 25 September, 2022; v1 submitted 16 June, 2022; originally announced June 2022.

Efficiency and time resolution of monolithic silicon pixel detectors in SiGe BiCMOS technology

Authors: G. Iacobucci, L. Paolozzi, P. Valerio, T. Moretti, F. Cadoux, R. Cardarelli, R. Cardella, S. Débieux, Y. Favre, D. Ferrere, S. Gonzalez-Sevilla, Y. Gurimskaya, R. Kotitsa, C. Magliocca, F. Martinelli, M. Milanesio, M. Münker, M. Nessi, A. Picardi, J. Saidi, H. Rücker, M. Vicente Barreto Pinto, S. Zambito

Abstract: A monolithic silicon pixel detector prototype has been produced in the SiGe BiCMOS SG13G2 130 nm node technology by IHP. The ASIC contains a matrix of hexagonal pixels with pitch of approximately 100 $μ$m. Three analog pixels were calibrated in laboratory with radioactive sources and tested in a 180 GeV/c pion beamline at the CERN SPS. A detection efficiency of $\left(99.9^{+0.1}_{-0.2}\right)$% w… ▽ More A monolithic silicon pixel detector prototype has been produced in the SiGe BiCMOS SG13G2 130 nm node technology by IHP. The ASIC contains a matrix of hexagonal pixels with pitch of approximately 100 $μ$m. Three analog pixels were calibrated in laboratory with radioactive sources and tested in a 180 GeV/c pion beamline at the CERN SPS. A detection efficiency of $\left(99.9^{+0.1}_{-0.2}\right)$% was measured together with a time resolution of $(36.4 \pm 0.8)$ps at the highest preamplifier bias current working point of 150 $μ$A and at a sensor bias voltage of 160 V. The ASIC was also characterized at lower bias voltage and preamplifier current. △ Less

Submitted 21 January, 2022; v1 submitted 16 December, 2021; originally announced December 2021.

The tracking detector of the FASER experiment

Authors: FASER Collaboration, Henso Abreu, Claire Antel, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David W. Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Olivier Crespo-Lopez, Sergey Dmitrievsky, Monica D'Onofrio, Candan Dozen, Abdallah Ezzat, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere, Stephen Gibson, Sergio Gonzalez-Sevilla , et al. (55 additional authors not shown)

Abstract: FASER is a new experiment designed to search for new light weakly-interacting long-lived particles (LLPs) and study high-energy neutrino interactions in the very forward region of the LHC collisions at CERN. The experimental apparatus is situated 480 m downstream of the ATLAS interaction-point aligned with the beam collision axis. The FASER detector includes four identical tracker stations constru… ▽ More FASER is a new experiment designed to search for new light weakly-interacting long-lived particles (LLPs) and study high-energy neutrino interactions in the very forward region of the LHC collisions at CERN. The experimental apparatus is situated 480 m downstream of the ATLAS interaction-point aligned with the beam collision axis. The FASER detector includes four identical tracker stations constructed from silicon microstrip detectors. Three of the tracker stations form a tracking spectrometer, and enable FASER to detect the decay products of LLPs decaying inside the apparatus, whereas the fourth station is used for the neutrino analysis. The spectrometer has been installed in the LHC complex since March 2021, while the fourth station is not yet installed. FASER will start physics data taking when the LHC resumes operation in early 2022. This paper describes the design, construction and testing of the tracking spectrometer, including the associated components such as the mechanics, readout electronics, power supplies and cooling system. △ Less

Submitted 31 May, 2022; v1 submitted 2 December, 2021; originally announced December 2021.

Journal ref: Nucl. Instrum. Methods Phys. Res., A 1034 (2022) 166825

The trigger and data acquisition system of the FASER experiment

Authors: FASER Collaboration, Henso Abreu, Elham Amin Mansour, Claire Antel, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David Casper, Charlotte Cavanagh, Xin Chen, Andrea Coccaro, Stephane Debieux, Sergey Dmitrievsky, Monica D'Onofrio, Candan Dozen, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere, Enrico Gamberini, Edward Karl Galantay , et al. (59 additional authors not shown)

Abstract: The FASER experiment is a new small and inexpensive experiment that is placed 480 meters downstream of the ATLAS experiment at the CERN LHC. FASER is designed to capture decays of new long-lived particles, produced outside of the ATLAS detector acceptance. These rare particles can decay in the FASER detector together with about 500-1000 Hz of other particles originating from the ATLAS interaction… ▽ More The FASER experiment is a new small and inexpensive experiment that is placed 480 meters downstream of the ATLAS experiment at the CERN LHC. FASER is designed to capture decays of new long-lived particles, produced outside of the ATLAS detector acceptance. These rare particles can decay in the FASER detector together with about 500-1000 Hz of other particles originating from the ATLAS interaction point. A very high efficiency trigger and data acquisition system is required to ensure that the physics events of interest will be recorded. This paper describes the trigger and data acquisition system of the FASER experiment and presents performance results of the system acquired during initial commissioning. △ Less

Submitted 10 January, 2022; v1 submitted 28 October, 2021; originally announced October 2021.

Journal ref: 2021_JINST_16_P12028

A 4pi time-of-flight detector for the ND280/T2K upgrade

Authors: A. Korzenev, F. Barao, S. Bordoni, D. Breton, F. Cadoux, Y. Favre, M. Khabibullin, A. Khotyantsev, Y. Kudenko, T. Lux, J. Maalmi, P. Mermod, O. Mineev, F. Sanchez

Abstract: ND280 is a near detector of the T2K experiment which is located in the J-PARC accelerator complex in Japan. After a decade of fruitful data-taking, ND280 is scheduled for upgrade. The time-of-flight (ToF) detector, which is described in this article, is one of three new detectors that will be installed in the basket of ND280. The ToF detector has a modular structure. Each module represents an arra… ▽ More ND280 is a near detector of the T2K experiment which is located in the J-PARC accelerator complex in Japan. After a decade of fruitful data-taking, ND280 is scheduled for upgrade. The time-of-flight (ToF) detector, which is described in this article, is one of three new detectors that will be installed in the basket of ND280. The ToF detector has a modular structure. Each module represents an array of 20 plastic scintillator bars which are stacked in a plane of 2.4 x 2.2 m2 area. Six modules of similar construction will be assembled in a cube, thus providing an almost 4pi enclosure for an active neutrino target and two TPCs. The light emitted by scintillator is absorbed by arrays of large-area silicon photo-multipliers (SiPMs) which are attached to both ends of every bar. The readout of SiPMs, sha** and analog sum of individual SiPM signals within the array are performed by a discrete circuit amplifier. An average time resolution of about 0.14 ns is achieved for a single bar when measured with cosmic muons. The detector will be installed in the basket of ND280, where it will be used to veto particle originating outside the neutrino target, improve the particle identification and provide a cosmic trigger for calibration of detectors which are enclosed inside it. △ Less

Submitted 25 December, 2021; v1 submitted 7 September, 2021; originally announced September 2021.

Comments: 9 pages, 5 figures

Journal ref: JINST 17 (2022) 01, P01016

First neutrino interaction candidates at the LHC

Authors: FASER Collaboration, Henso Abreu, Yoav Afik, Claire Antel, Jason Arakawa, Akitaka Ariga, Tomoko Ariga, Florian Bernlochner, Tobias Boeckh, Jamie Boyd, Lydia Brenner, Franck Cadoux, David W. Casper, Charlotte Cavanagh, Francesco Cerutti, Xin Chen, Andrea Coccaro, Monica D'Onofrio, Candan Dozen, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere, Stephen Gibson, Sergio Gonzalez-Sevilla , et al. (51 additional authors not shown)

Abstract: FASER$ν$ at the CERN Large Hadron Collider (LHC) is designed to directly detect collider neutrinos for the first time and study their cross sections at TeV energies, where no such measurements currently exist. In 2018, a pilot detector employing emulsion films was installed in the far-forward region of ATLAS, 480 m from the interaction point, and collected 12.2 fb$^{-1}$ of proton-proton collision… ▽ More FASER$ν$ at the CERN Large Hadron Collider (LHC) is designed to directly detect collider neutrinos for the first time and study their cross sections at TeV energies, where no such measurements currently exist. In 2018, a pilot detector employing emulsion films was installed in the far-forward region of ATLAS, 480 m from the interaction point, and collected 12.2 fb$^{-1}$ of proton-proton collision data at a center-of-mass energy of 13 TeV. We describe the analysis of this pilot run data and the observation of the first neutrino interaction candidates at the LHC. This milestone paves the way for high-energy neutrino measurements at current and future colliders. △ Less

Submitted 26 October, 2021; v1 submitted 13 May, 2021; originally announced May 2021.

Comments: Auxiliary materials are available at https://faser.web.cern.ch/fasernu-first-neutrino-interaction-candidates

The SuperFGD Prototype Charged Particle Beam Tests

Authors: A. Blondel, M. Bogomilov, S. Bordoni, F. Cadoux, D. Douqa, K. Dugas, T. Ekelof, Y. Favre, S. Fedotov, K. Fransson, R. Fujita, E. Gramstad, A. K. Ichikawa, S. Ilieva, K. Iwamoto, C. Jesus-Valls, C. K. Jung, S. P. Kasetti, M. Khabibullin, A. Khotjantsev, A. Korzenev, A. Kostin, Y. Kudenko, T. Kutter, T. Lux , et al. (25 additional authors not shown)

Abstract: A novel scintillator detector, the SuperFGD, has been selected as the main neutrino target for an upgrade of the T2K experiment ND280 near detector. The detector design will allow nearly 4π coverage for neutrino interactions at the near detector and will provide lower energy thresholds, significantly reducing systematic errors for the experiment. The SuperFGD is made of optically-isolated scintill… ▽ More A novel scintillator detector, the SuperFGD, has been selected as the main neutrino target for an upgrade of the T2K experiment ND280 near detector. The detector design will allow nearly 4π coverage for neutrino interactions at the near detector and will provide lower energy thresholds, significantly reducing systematic errors for the experiment. The SuperFGD is made of optically-isolated scintillator cubes of size 10x10x10 mm^3, providing the required spatial and energy resolution to reduce systematic uncertainties for future T2K runs. The SuperFGD for T2K will have close to two million cubes in a 1920x560x1840 mm^3 volume. A prototype made of 24x8x48 cubes was tested at a charged particle beamline at the CERN PS facility. The SuperFGD Prototype was instrumented with readout electronics similar to the future implementation for T2K. Results on electronics and detector response are reported in this paper, along with a discussion of the 3D reconstruction capabilities of this type of detector. Several physics analyses with the prototype data are also discussed, including a study of stop** protons. △ Less

Submitted 7 September, 2020; v1 submitted 20 August, 2020; originally announced August 2020.

Comments: 36 pages, 29 figures, Edited acknowledgements

Time resolution and power consumption of a monolithic silicon pixel prototype in SiGe BiCMOS technology

Authors: L. Paolozzi, R. Cardarelli, S. Débieux, Y. Favre, D. Ferrère, S. Gonzalez-Sevilla, G. Iacobucci, M. Kaynak, F. Martinelli, M. Nessi, H. Rücker, I. Sanna, DMS Sultan, P. Valerio, E. Zaffaroni

Abstract: SiGe BiCMOS technology can be used to produce ultra-fast, low-power silicon pixel sensors that provide state-of-the-art time resolution even without an internal gain mechanism. The development of such sensors requires the identification of the main factors that may degrade the timing performance and the characterisation of the dependance of the sensor time resolution on the amplifier power consump… ▽ More SiGe BiCMOS technology can be used to produce ultra-fast, low-power silicon pixel sensors that provide state-of-the-art time resolution even without an internal gain mechanism. The development of such sensors requires the identification of the main factors that may degrade the timing performance and the characterisation of the dependance of the sensor time resolution on the amplifier power consumption. Measurements with a $ \mathrm{^{90}Sr} $ source of a prototype sensor produced in SG13G2 technology from IHP Microelectronics, shows a time resolution of 140 ps at an amplifier current of 7 $ \mathrmμ $A and 45 ps at higher power consumption. A full simulation shows that the resolution on the measurement of the signal time-over-threshold, used to correct for time walk, is the main factor affecting the timing performance. △ Less

Submitted 28 August, 2020; v1 submitted 28 May, 2020; originally announced May 2020.

Technical Proposal: FASERnu

Authors: FASER Collaboration, Henso Abreu, Marco Andreini, Claire Antel, Akitaka Ariga, Tomoko Ariga, Caterina Bertone, Jamie Boyd, Andy Buckley, Franck Cadoux, David W. Casper, Francesco Cerutti, Xin Chen, Andrea Coccaro, Salvatore Danzeca, Liam Dougherty, Candan Dozen, Peter B. Denton, Yannick Favre, Deion Fellers, Jonathan L. Feng, Didier Ferrere, Jonathan Gall, Iftah Galon, Stephen Gibson , et al. (47 additional authors not shown)

Abstract: FASERnu is a proposed small and inexpensive emulsion detector designed to detect collider neutrinos for the first time and study their properties. FASERnu will be located directly in front of FASER, 480 m from the ATLAS interaction point along the beam collision axis in the unused service tunnel TI12. From 2021-23 during Run 3 of the 14 TeV LHC, roughly 1,300 electron neutrinos, 20,000 muon neutri… ▽ More FASERnu is a proposed small and inexpensive emulsion detector designed to detect collider neutrinos for the first time and study their properties. FASERnu will be located directly in front of FASER, 480 m from the ATLAS interaction point along the beam collision axis in the unused service tunnel TI12. From 2021-23 during Run 3 of the 14 TeV LHC, roughly 1,300 electron neutrinos, 20,000 muon neutrinos, and 20 tau neutrinos will interact in FASERnu with TeV-scale energies. With the ability to observe these interactions, reconstruct their energies, and distinguish flavors, FASERnu will probe the production, propagation, and interactions of neutrinos at the highest human-made energies ever recorded. The FASERnu detector will be composed of 1000 emulsion layers interleaved with tungsten plates. The total volume of the emulsion and tungsten is 25cm x 25cm x 1.35m, and the tungsten target mass is 1.2 tonnes. From 2021-23, 7 sets of emulsion layers will be installed, with replacement roughly every 20-50 1/fb in planned Technical Stops. In this document, we summarize FASERnu's physics goals and discuss the estimates of neutrino flux and interaction rates. We then describe the FASERnu detector in detail, including plans for assembly, transport, installation, and emulsion replacement, and procedures for emulsion readout and analyzing the data. We close with cost estimates for the detector components and infrastructure work and a timeline for the experiment. △ Less

Submitted 9 January, 2020; originally announced January 2020.

Comments: 49 pages, 25 figures; submitted to the CERN LHCC on 28 October 2019

Report number: CERN-LHCC-2019-017, LHCC-P-015, UCI-TR-2019-25

A 50 ps resolution monolithic active pixel sensor without internal gain in SiGe BiCMOS technology

Authors: G. Iacobucci, R. Cardarelli, S. Débieux, F. A. Di Bello, Y. Favre, D. Hayakawa, M. Kaynak, M. Nessi, L. Paolozzi, H. Rücker, DMS Sultan, P. Valerio

Abstract: A monolithic pixelated silicon detector designed for high time resolution has been produced in the SG13G2 130 nm SiGe BiCMOS technology of IHP Mikroelektronik. This proof-of-concept chip contains hexagonal pixels of 65 μm and 130 μm side. The SiGe front-end electronics implemented provides an equivalent noise charge of 90 and 160 electrons for a pixel capacitance of 70 and 220 fF, respectively, an… ▽ More A monolithic pixelated silicon detector designed for high time resolution has been produced in the SG13G2 130 nm SiGe BiCMOS technology of IHP Mikroelektronik. This proof-of-concept chip contains hexagonal pixels of 65 μm and 130 μm side. The SiGe front-end electronics implemented provides an equivalent noise charge of 90 and 160 electrons for a pixel capacitance of 70 and 220 fF, respectively, and a total time walk of less than 1 ns. Lab measurements with a 90Sr source show a time resolution of the order of 50 ps. This result is competitive with silicon technologies that integrate an avalanche gain mechanism. △ Less

Submitted 26 August, 2019; originally announced August 2019.

Detecting and Studying High-Energy Collider Neutrinos with FASER at the LHC

Authors: FASER Collaboration, Henso Abreu, Claire Antel, Akitaka Ariga, Tomoko Ariga, Jamie Boyd, Franck Cadoux, David W. Casper, Xin Chen, Andrea Coccaro, Candan Dozen, Peter B. Denton, Yannick Favre, Jonathan L. Feng, Didier Ferrere, Iftah Galon, Stephen Gibson, Sergio Gonzalez-Sevilla, Shih-Chieh Hsu, Zhen Hu, Giuseppe Iacobucci, Sune Jakobsen, Roland Jansky, Enrique Kajomovitz, Felix Kling , et al. (23 additional authors not shown)

Abstract: Neutrinos are copiously produced at particle colliders, but no collider neutrino has ever been detected. Colliders, and particularly hadron colliders, produce both neutrinos and anti-neutrinos of all flavors at very high energies, and they are therefore highly complementary to those from other sources. FASER, the recently approved Forward Search Experiment at the Large Hadron Collider, is ideally… ▽ More Neutrinos are copiously produced at particle colliders, but no collider neutrino has ever been detected. Colliders, and particularly hadron colliders, produce both neutrinos and anti-neutrinos of all flavors at very high energies, and they are therefore highly complementary to those from other sources. FASER, the recently approved Forward Search Experiment at the Large Hadron Collider, is ideally located to provide the first detection and study of collider neutrinos. We investigate the prospects for neutrino studies of a proposed component of FASER, FASER$ν$, a 25cm x 25cm x 1.35m emulsion detector to be placed directly in front of the FASER spectrometer in tunnel TI12. FASER$ν$ consists of 1000 layers of emulsion films interleaved with 1-mm-thick tungsten plates, with a total tungsten target mass of 1.2 tons. We estimate the neutrino fluxes and interaction rates at FASER$ν$, describe the FASER$ν$ detector, and analyze the characteristics of the signals and primary backgrounds. For an integrated luminosity of 150 fb$^{-1}$ to be collected during Run 3 of the 14 TeV Large Hadron Collider from 2021-23, and assuming standard model cross sections, approximately 1300 electron neutrinos, 20,000 muon neutrinos, and 20 tau neutrinos will interact in FASER$ν$, with mean energies of 600 GeV to 1 TeV, depending on the flavor. With such rates and energies, FASER will measure neutrino cross sections at energies where they are currently unconstrained, will bound models of forward particle production, and could open a new window on physics beyond the standard model. △ Less

Submitted 20 February, 2020; v1 submitted 6 August, 2019; originally announced August 2019.

Comments: Version published in EPJ C

Report number: CERN-EP-2019-160, KYUSHU-RCAPP-2019-003, SLAC-PUB-17460, UCI-TR-2019-19

Journal ref: Eur.Phys.J. C80 (2020) no.1, 61

FASER: ForwArd Search ExpeRiment at the LHC

Authors: FASER Collaboration, Akitaka Ariga, Tomoko Ariga, Jamie Boyd, Franck Cadoux, David W. Casper, Yannick Favre, Jonathan L. Feng, Didier Ferrere, Iftah Galon, Sergio Gonzalez-Sevilla, Shih-Chieh Hsu, Giuseppe Iacobucci, Enrique Kajomovitz, Felix Kling, Susanne Kuehn, Lorne Levinson, Hidetoshi Otono, Brian Petersen, Osamu Sato, Matthias Schott, Anna Sfyrla, Jordan Smolinsky, Aaron M. Soffa, Yosuke Takubo , et al. (3 additional authors not shown)

Abstract: FASER, the ForwArd Search ExpeRiment, is a proposed experiment dedicated to searching for light, extremely weakly-interacting particles at the LHC. Such particles may be produced in the LHC's high-energy collisions in large numbers in the far-forward region and then travel long distances through concrete and rock without interacting. They may then decay to visible particles in FASER, which is plac… ▽ More FASER, the ForwArd Search ExpeRiment, is a proposed experiment dedicated to searching for light, extremely weakly-interacting particles at the LHC. Such particles may be produced in the LHC's high-energy collisions in large numbers in the far-forward region and then travel long distances through concrete and rock without interacting. They may then decay to visible particles in FASER, which is placed 480 m downstream of the ATLAS interaction point. In this work, we describe the FASER program. In its first stage, FASER is an extremely compact and inexpensive detector, sensitive to decays in a cylindrical region of radius R = 10 cm and length L = 1.5 m. FASER is planned to be constructed and installed in Long Shutdown 2 and will collect data during Run 3 of the 14 TeV LHC from 2021-23. If FASER is successful, FASER 2, a much larger successor with roughly R ~ 1 m and L ~ 5 m, could be constructed in Long Shutdown 3 and collect data during the HL-LHC era from 2026-35. FASER and FASER 2 have the potential to discover dark photons, dark Higgs bosons, heavy neutral leptons, axion-like particles, and many other long-lived particles, as well as provide new information about neutrinos, with potentially far-ranging implications for particle physics and cosmology. We describe the current status, anticipated challenges, and discovery prospects of the FASER program. △ Less

Submitted 11 January, 2019; originally announced January 2019.

Comments: 13 pages, 4 figures, submitted as Input to the European Particle Physics Strategy Update 2018-2020 and draws on FASER's Letter of Intent, Technical Proposal, and physics case documents (arXiv:1811.10243, arXiv:1812.09139, and arXiv:1811.12522)

Report number: UCI-TR-2019-01, KYUSHU-RCAPP-2018-08

T2K ND280 Upgrade -- Technical Design Report

Authors: K. Abe, H. Aihara, A. Ajmi, C. Andreopoulos, M. Antonova, S. Aoki, Y. Asada, Y. Ashida, A. Atherton, E. Atkin, D. Attié, S. Ban, M. Barbi, G. J. Barker, G. Barr, M. Batkiewicz, A. Beloshapkin, V. Berardi, L. Berns, S. Bhadra, J. Bian, S. Bienstock, A. Blondel, J. Boix, S. Bolognesi , et al. (359 additional authors not shown)

Abstract: In this document, we present the Technical Design Report of the Upgrade of the T2K Near Detector ND280. The goal of this upgrade is to improve the Near Detector performance to measure the neutrino interaction rate and to constrain the neutrino interaction cross-sections so that the uncertainty in the number of predicted events at Super-Kamiokande is reduced to about 4%. This will allow to improve… ▽ More In this document, we present the Technical Design Report of the Upgrade of the T2K Near Detector ND280. The goal of this upgrade is to improve the Near Detector performance to measure the neutrino interaction rate and to constrain the neutrino interaction cross-sections so that the uncertainty in the number of predicted events at Super-Kamiokande is reduced to about 4%. This will allow to improve the physics reach of the T2K-II project. This goal is achieved by modifying the upstream part of the detector, adding a new highly granular scintillator detector (Super-FGD), two new TPCs (High-Angle TPC) and six TOF planes. Details about the detector concepts, design and construction methods are presented, as well as a first look at the test-beam data taken in Summer 2018. An update of the physics studies is also presented. △ Less

Submitted 14 October, 2020; v1 submitted 11 January, 2019; originally announced January 2019.

Comments: 196 pages

Report number: CERN-SPSC-2019-001 (SPSC-TDR-006)

Technical Proposal for FASER: ForwArd Search ExpeRiment at the LHC

Authors: FASER Collaboration, Akitaka Ariga, Tomoko Ariga, Jamie Boyd, Franck Cadoux, David W. Casper, Francesco Cerutti, Salvatore Danzeca, Liam Dougherty, Yannick Favre, Jonathan L. Feng, Didier Ferrere, Jonathan Gall, Iftah Galon, Sergio Gonzalez-Sevilla, Shih-Chieh Hsu, Giuseppe Iacobucci, Enrique Kajomovitz, Felix Kling, Susanne Kuehn, Mike Lamont, Lorne Levinson, Hidetoshi Otono, John Osborne, Brian Petersen , et al. (11 additional authors not shown)

Abstract: FASER is a proposed small and inexpensive experiment designed to search for light, weakly-interacting particles during Run 3 of the LHC from 2021-23. Such particles may be produced in large numbers along the beam collision axis, travel for hundreds of meters without interacting, and then decay to standard model particles. To search for such events, FASER will be located 480 m downstream of the ATL… ▽ More FASER is a proposed small and inexpensive experiment designed to search for light, weakly-interacting particles during Run 3 of the LHC from 2021-23. Such particles may be produced in large numbers along the beam collision axis, travel for hundreds of meters without interacting, and then decay to standard model particles. To search for such events, FASER will be located 480 m downstream of the ATLAS IP in the unused service tunnel TI12 and be sensitive to particles that decay in a cylindrical volume with radius R=10 cm and length L=1.5 m. FASER will complement the LHC's existing physics program, extending its discovery potential to a host of new, light particles, with potentially far-reaching implications for particle physics and cosmology. This document describes the technical details of the FASER detector components: the magnets, the tracker, the scintillator system, and the calorimeter, as well as the trigger and readout system. The preparatory work that is needed to install and operate the detector, including civil engineering, transport, and integration with various services is also presented. The information presented includes preliminary cost estimates for the detector components and the infrastructure work, as well as a timeline for the design, construction, and installation of the experiment. △ Less

Submitted 21 December, 2018; originally announced December 2018.

Comments: 82 pages, 62 figures; submitted to the CERN LHCC on 7 November 2018

Report number: CERN-LHCC-2018-036, LHCC-P-013, UCI-TR-2018-22, KYUSHU-RCAPP-2018-07

The TT-PET Data Acquisition and Trigger System

Authors: Y. Bandi, Y. Favre, D. Ferrere, D. Forshaw, R. Hanni, D. Hayakawa, G. Iacobucci, P. Lutz, A. Miucci, L. Paolozzi, E. Ripiccini, C. Tognina, P. Valerio, M. Weber

Abstract: This paper describes the data acquisition and trigger system of the Thin Time-of-flight PET (TT-PET) scanner. The system is designed to read out in the order of 1000 pixel sensors used in the scanner and to provide a reference timing signal to each sensor in order to measure time differences of better than 30 ps. This clock distribution is measured to have a jitter of less than 4 ps at the sensors… ▽ More This paper describes the data acquisition and trigger system of the Thin Time-of-flight PET (TT-PET) scanner. The system is designed to read out in the order of 1000 pixel sensors used in the scanner and to provide a reference timing signal to each sensor in order to measure time differences of better than 30 ps. This clock distribution is measured to have a jitter of less than 4 ps at the sensors. Collected data is locally processed before being forwarded to storage. Data flow as well as control, configuration and monitoring aspects are are also addressed. △ Less

Submitted 10 December, 2018; originally announced December 2018.

Characterization of the demonstrator of the fast silicon monolithic ASIC for the TT-PET project

Authors: Lorenzo Paolozzi, Yves Bandi, Roberto Cardarelli, Stephane Debieux, Yannick Favre, Didier Ferrere, Dean Forshaw, Daiki Hayakawa, Giuseppe Iacobucci, Mehmet Kaynak, Antonio Miucci, Marzio Nessi, Emanuele Ripiccini, Holger Ruecker, Pierpaolo Valerio, Michele Weber

Abstract: The TT-PET collaboration is develo** a small animal TOF-PET scanner based on monolithic silicon pixel sensors in SiGe BiCMOS technology. The demonstrator chip, a small-scale version of the final detector ASIC, consists of a 3 x 10 pixel matrix integrated with the front-end, a 50 ps binning TDC and read out logic. The chip, thinned down to 100 μm and backside metallized, was operated at a voltage… ▽ More The TT-PET collaboration is develo** a small animal TOF-PET scanner based on monolithic silicon pixel sensors in SiGe BiCMOS technology. The demonstrator chip, a small-scale version of the final detector ASIC, consists of a 3 x 10 pixel matrix integrated with the front-end, a 50 ps binning TDC and read out logic. The chip, thinned down to 100 μm and backside metallized, was operated at a voltage of 180 V. The tests on a beam line of minimum ionizing particles show a detection efficiency greater than 99.9 % and a time resolution down to 110 ps. △ Less

Submitted 27 November, 2018; originally announced November 2018.

Beam test results of 3D fine-grained scintillator detector prototype for a T2K ND280 neutrino active target

Authors: O. Mineev, A. Blondel, Y. Favre, S. Fedotov, A. Khotjantsev, A. Korzenev, Yu. Kudenko, A. Mefodiev, E. Noah, D. Sgalaberna, S. Suvorov

Abstract: An upgrade of the long baseline neutrino experiment T2K near detector ND280 is currently being developed with the goal to reduce systematic uncertainties in the prediction of number of events at the far detector Super-Kamiokande. The upgrade program includes the design and construction of a new highly granular fully active scintillator detector with 3D WLS fiber readout as a neutrino target. The d… ▽ More An upgrade of the long baseline neutrino experiment T2K near detector ND280 is currently being developed with the goal to reduce systematic uncertainties in the prediction of number of events at the far detector Super-Kamiokande. The upgrade program includes the design and construction of a new highly granular fully active scintillator detector with 3D WLS fiber readout as a neutrino target. The detector of about $200\times 180\times 60~cm^3$ in size and a mass of $\sim$2.2~tons will be assembled from about $2\times10^6$ plastic scintillator cubes of $1\times1\times1~cm^3$. Each cube is read out by three orthogonal Kuraray Y11 Wave Length Shifting (WLS) fibers threaded through the detector. A detector prototype made of 125 cubes was assembled and tested in a charged particle test beam at CERN in the fall of 2017. This paper presents the results obtained on the light yield and timing as well as on the optical cross-talk between the cubes. △ Less

Submitted 27 August, 2018; originally announced August 2018.

Comments: 5 pages, 8 figures

Production and Integration of the ATLAS Insertable B-Layer

Authors: B. Abbott, J. Albert, F. Alberti, M. Alex, G. Alimonti, S. Alkire, P. Allport, S. Altenheiner, L. Ancu, E. Anderssen, A. Andreani, A. Andreazza, B. Axen, J. Arguin, M. Backhaus, G. Balbi, J. Ballansat, M. Barbero, G. Barbier, A. Bassalat, R. Bates, P. Baudin, M. Battaglia, T. Beau, R. Beccherle , et al. (352 additional authors not shown)

Abstract: During the shutdown of the CERN Large Hadron Collider in 2013-2014, an additional pixel layer was installed between the existing Pixel detector of the ATLAS experiment and a new, smaller radius beam pipe. The motivation for this new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the robustness and performance of the ATLAS tracking system, given the higher instantaneous and i… ▽ More During the shutdown of the CERN Large Hadron Collider in 2013-2014, an additional pixel layer was installed between the existing Pixel detector of the ATLAS experiment and a new, smaller radius beam pipe. The motivation for this new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the robustness and performance of the ATLAS tracking system, given the higher instantaneous and integrated luminosities realised following the shutdown. Because of the extreme radiation and collision rate environment, several new radiation-tolerant sensor and electronic technologies were utilised for this layer. This paper reports on the IBL construction and integration prior to its operation in the ATLAS detector. △ Less

Submitted 6 June, 2018; v1 submitted 2 March, 2018; originally announced March 2018.

Comments: 90 pages in total. Author list: ATLAS IBL Collaboration, starting page 2. 69 figures, 20 tables. Published in Journal of Instrumentation. All figures available at: https://atlas.web.cern.ch/Atlas/GROUPS/PHYSICS/PLOTS/PIX-2018-001

Journal ref: Journal of Instrumentation JINST 13 T05008 (2018)

Application of large area SiPMs for the readout of a plastic scintillator based timing detector

Authors: C. Betancourt, A. Blondel, R. Brundler, A. Datwyler, Y. Favre, D. Gascon, S. Gomez, A. Korzenev, P. Mermod, E. Noah, N. Serra, D. Sgalaberna, B. Storaci

Abstract: In this study an array of eight 6 mm x 6 mm area SiPMs was coupled to the end of a long plastic scintillator counter which was exposed to a 2.5 GeV/c muon beam at the CERN PS. Timing characteristics of bars with dimensions 150 cm x 6 cm x 1 cm and 120 cm x 11 cm x 2.5 cm have been studied. An 8-channel SiPM anode readout ASIC (MUSIC R1) based on a novel low input impedance current conveyor has bee… ▽ More In this study an array of eight 6 mm x 6 mm area SiPMs was coupled to the end of a long plastic scintillator counter which was exposed to a 2.5 GeV/c muon beam at the CERN PS. Timing characteristics of bars with dimensions 150 cm x 6 cm x 1 cm and 120 cm x 11 cm x 2.5 cm have been studied. An 8-channel SiPM anode readout ASIC (MUSIC R1) based on a novel low input impedance current conveyor has been used to read out and amplify SiPMs independently and sum the signals at the end. Prospects for applications in large-scale particle physics detectors with timing resolution below 100 ps are provided in light of the results. △ Less

Submitted 16 December, 2017; v1 submitted 26 September, 2017; originally announced September 2017.

Journal ref: JINST 12 (2017) P11023

Baby MIND: A magnetized segmented neutrino detector for the WAGASCI experiment

Authors: M. Antonova, R. Asfandiyarov, R. Bayes, P. Benoit, A. Blondel, M. Bogomilov, A. Bross, F. Cadoux, A. Cervera, N. Chikuma, A. Dudarev, T. Ekelöf, Y. Favre, S. Fedotov, S-P. Hallsjö, A. Izmaylov, Y. Karadzhov, M. Khabibullin, A. Khotyantsev, A. Kleymenova, T. Koga, A. Kostin, Y. Kudenko, V. Likhacheva, B. Martinez , et al. (21 additional authors not shown)

Abstract: T2K (Tokai-to-Kamioka) is a long-baseline neutrino experiment in Japan designed to study various parameters of neutrino oscillations. A near detector complex (ND280) is located 280~m downstream of the production target and measures neutrino beam parameters before any oscillations occur. ND280's measurements are used to predict the number and spectra of neutrinos in the Super-Kamiokande detector at… ▽ More T2K (Tokai-to-Kamioka) is a long-baseline neutrino experiment in Japan designed to study various parameters of neutrino oscillations. A near detector complex (ND280) is located 280~m downstream of the production target and measures neutrino beam parameters before any oscillations occur. ND280's measurements are used to predict the number and spectra of neutrinos in the Super-Kamiokande detector at the distance of 295~km. The difference in the target material between the far (water) and near (scintillator, hydrocarbon) detectors leads to the main non-cancelling systematic uncertainty for the oscillation analysis. In order to reduce this uncertainty a new WAter-Grid-And-SCintillator detector (WAGASCI) has been developed. A magnetized iron neutrino detector (Baby MIND) will be used to measure momentum and charge identification of the outgoing muons from charged current interactions. The Baby MIND modules are composed of magnetized iron plates and long plastic scintillator bars read out at the both ends with wavelength shifting fibers and silicon photomultipliers. The front-end electronics board has been developed to perform the readout and digitization of the signals from the scintillator bars. Detector elements were tested with cosmic rays and in the PS beam at CERN. The obtained results are presented in this paper. △ Less

Submitted 16 July, 2017; v1 submitted 29 May, 2017; originally announced May 2017.

Comments: In new version: modified both plots of Fig.1 and added one sentence in the introduction part explaining Baby MIND role in WAGASCI experiment, added information for the affiliations

Baby MIND Experiment Construction Status

Authors: M. Antonova, R. Asfandiyarov, R Bayes, P. Benoit, A. Blondel, M. Bogomilov, A. Bross, F. Cadoux, A. Cervera, N. Chikuma, A. Dudarev, T. Ekelöf, Y. Favre, S. Fedotov, S-P. Hallsjö, A. Izmaylov, Y. Karadzhov, M. Khabibullin, A. Khotyantsev, A. Kleymenova, T. Koga, A. Kostin, Y. Kudenko, V. Likhacheva, B. Martinez , et al. (21 additional authors not shown)

Abstract: Baby MIND is a magnetized iron neutrino detector, with novel design features, and is planned to serve as a downstream magnetized muon spectrometer for the WAGASCI experiment on the T2K neutrino beam line in Japan. One of the main goals of this experiment is to reduce systematic uncertainties relevant to CP-violation searches, by measuring the neutrino contamination in the anti-neutrino beam mode o… ▽ More Baby MIND is a magnetized iron neutrino detector, with novel design features, and is planned to serve as a downstream magnetized muon spectrometer for the WAGASCI experiment on the T2K neutrino beam line in Japan. One of the main goals of this experiment is to reduce systematic uncertainties relevant to CP-violation searches, by measuring the neutrino contamination in the anti-neutrino beam mode of T2K. Baby MIND is currently being constructed at CERN, and is planned to be operational in Japan in October 2017. △ Less

Submitted 28 April, 2017; originally announced April 2017.

Comments: Poster presented at NuPhys2016 (London, 12-14 December 2016). 4 pages, LaTeX, 7 figures

Report number: NuPhys2016-Parsa

Baby MIND: A magnetised spectrometer for the WAGASCI experiment

Authors: M. Antonova, R. Asfandiyarov, R Bayes, P. Benoit, A. Blondel, M. Bogomilov, A. Cross, F. Cadoux, A. Cervera, N. Chikuma, A. Dudarev, T. Ekelöf, Y. Favre, S. Fedotov, S-P. Hallsjö, A. Izmaylov, Y. Karadzhov, M. Khabibullin, A. Khotyantsev, A. Kleymenova, T. Koga, A. Kostin, Y. Kudenko, V. Likhacheva, B. Martinez , et al. (21 additional authors not shown)

Abstract: The WAGASCI experiment being built at the J-PARC neutrino beam line will measure the difference in cross sections from neutrinos interacting with a water and scintillator targets, in order to constrain neutrino cross sections, essential for the T2K neutrino oscillation measurements. A prototype Magnetised Iron Neutrino Detector (MIND), called Baby MIND, is being constructed at CERN to act as a mag… ▽ More The WAGASCI experiment being built at the J-PARC neutrino beam line will measure the difference in cross sections from neutrinos interacting with a water and scintillator targets, in order to constrain neutrino cross sections, essential for the T2K neutrino oscillation measurements. A prototype Magnetised Iron Neutrino Detector (MIND), called Baby MIND, is being constructed at CERN to act as a magnetic spectrometer behind the main WAGASCI target to be able to measure the charge and momentum of the outgoing muon from neutrino charged current interactions. △ Less

Submitted 26 April, 2017; originally announced April 2017.

Comments: Poster presented at NuPhys2016 (London, 12-14 December 2016). Title + 4 pages, LaTeX, 6 figures

Report number: NuPhys2016-Hallsj\"o

An innovative silicon photomultiplier digitizing camera for gamma-ray astronomy

Authors: Matthieu Heller, Enrico Junior Schioppa, Alessio Porcelli, Isaac Troyano Pujadas, Krzysztof Zietara, Domenico Della Volpe, Teresa Montaruli, Franck Cadoux, Yannick Favre, Juan Antonio Aguilar Sanchez, Asen Christov, Elisa Prandini, Pawel Rajda, Mohamed Rameez, Woijciech Blinik, Jacek Blocki, Leszek Bogacz, Jurek Borkowski, Tomasz Bulik, Adam Frankowski, Mira Grudzinska, Bartosz Idzkowski, Mateusz Jamrozy, Mateusz Janiak, Jerzy Kasperek , et al. (22 additional authors not shown)

Abstract: The single-mirror small-size telescope (SST-1M) is one of the three proposed designs for the small-size telescopes (SSTs) of the Cherenkov Telescope Array (CTA) project. The SST-1M will be equipped with a 4 m-diameter segmented mirror dish and an innovative fully digital camera based on silicon photo-multipliers (SiPMs). Since the SST sub-array will consist of up to 70 telescopes, the challenge is… ▽ More The single-mirror small-size telescope (SST-1M) is one of the three proposed designs for the small-size telescopes (SSTs) of the Cherenkov Telescope Array (CTA) project. The SST-1M will be equipped with a 4 m-diameter segmented mirror dish and an innovative fully digital camera based on silicon photo-multipliers (SiPMs). Since the SST sub-array will consist of up to 70 telescopes, the challenge is not only to build a telescope with excellent performance, but also to design it so that its components can be commissioned, assembled and tested by industry. In this paper we review the basic steps that led to the design concepts for the SST-1M camera and the ongoing realization of the first prototype, with focus on the innovative solutions adopted for the photodetector plane and the readout and trigger parts of the camera. In addition, we report on results of laboratory measurements on real scale elements that validate the camera design and show that it is capable of matching the CTA requirements of operating up to high-moon-light background conditions. △ Less

Submitted 12 July, 2016; originally announced July 2016.

Comments: 30 pages, 61 figures

100ps time resolution with thin silicon pixel detectors and a SiGe HBT amplifier

Authors: Mathieu Benoit, Roberto Cardarelli, Stéphane Débieux, Yannick Favre, Giuseppe Iacobucci, Marzio Nessi, Lorenzo Paolozzi, Kenji Shu

Abstract: A 100um thick silicon detector with 1mm2 pad readout optimized for sub-nanosecond time resolution has been developed and tested. Coupled to a purposely developed amplifier based on SiGe HBT technology, this detector was characterized at the H8 beam line at the CERN SPS. An excellent time resolution of (106+-1)ps for silicon detectors was measured with minimum ionizing particles. A 100um thick silicon detector with 1mm2 pad readout optimized for sub-nanosecond time resolution has been developed and tested. Coupled to a purposely developed amplifier based on SiGe HBT technology, this detector was characterized at the H8 beam line at the CERN SPS. An excellent time resolution of (106+-1)ps for silicon detectors was measured with minimum ionizing particles. △ Less

Submitted 13 November, 2015; originally announced November 2015.

The SIRIUS Mixed analog-digital ASIC developed for the LOFT LAD and WFM instruments

Authors: A. Cros, D. Rambaud, E. Moutaye, L. Ravera, D. Barret, P. Caïs, R. Clédassou, P. Bodin, JY. Seyler, A. Bonzo, M. Feroci, C. Labanti, Y. Evangelista, Y. Favre

Abstract: We report on the development and characterization of the low-noise, low power, mixed analog-digital SIRIUS ASICs for both the LAD and WFM X-ray instruments of LOFT. The ASICs we developed are reading out large area silicon drift detectors (SDD). Stringent requirements in terms of noise (ENC of 17 e- to achieve an energy resolution on the LAD of 200 eV FWHM at 6 keV) and power consumption (650 μW p… ▽ More We report on the development and characterization of the low-noise, low power, mixed analog-digital SIRIUS ASICs for both the LAD and WFM X-ray instruments of LOFT. The ASICs we developed are reading out large area silicon drift detectors (SDD). Stringent requirements in terms of noise (ENC of 17 e- to achieve an energy resolution on the LAD of 200 eV FWHM at 6 keV) and power consumption (650 μW per channel) were basis for the ASICs design. These SIRIUS ASICs are developed to match SDD detectors characteristics: 16 channels ASICs adapted for the LAD (970 microns pitch) and 64 channels for the WFM (145 microns pitch) will be fabricated. The ASICs were developed with the 180nm mixed technology of TSMC. △ Less

Submitted 27 August, 2014; originally announced August 2014.

Comments: Proc. SPIE 9144, Space Telescopes and Instrumentation 2014: Ultraviolet to Gamma Ray, 914463

Characterization of the VEGA ASIC coupled to large area position-sensitive Silicon Drift Detectors

Authors: R. Campana, Y. Evangelista, F. Fuschino, M. Ahangarianabhari, D. Macera, G. Bertuccio, M. Grassi, C. Labanti, M. Marisaldi, P. Malcovati, A. Rachevski, G. Zampa, N. Zampa, L. Andreani, G. Baldazzi, E. Del Monte, Y. Favre, M. Feroci, F. Muleri, I. Rashevskaya, A. Vacchi, F. Ficorella, G. Giacomini, A. Picciotto, M. Zuffa

Abstract: Low-noise, position-sensitive Silicon Drift Detectors (SDDs) are particularly useful for experiments in which a good energy resolution combined with a large sensitive area is required, as in the case of X-ray astronomy space missions and medical applications. This paper presents the experimental characterization of VEGA, a custom Application Specific Integrated Circuit (ASIC) used as the front-end… ▽ More Low-noise, position-sensitive Silicon Drift Detectors (SDDs) are particularly useful for experiments in which a good energy resolution combined with a large sensitive area is required, as in the case of X-ray astronomy space missions and medical applications. This paper presents the experimental characterization of VEGA, a custom Application Specific Integrated Circuit (ASIC) used as the front-end electronics for XDXL-2, a large-area (30.5 cm^2) SDD prototype. The ASICs were integrated on a specifically developed PCB hosting also the detector. Results on the ASIC noise performances, both stand-alone and bonded to the large area SDD, are presented and discussed. △ Less

Submitted 7 July, 2014; originally announced July 2014.

Comments: 15 pages, 11 figures. Accepted for publication in Journal of Instrumentation (JINST)

Journal ref: Journal of Instrumentation, Volume 9, August 2014