-
Directional Filter Design and Simulation for Superconducting On-chip Filter-banks
Authors:
Louis H. Marting,
Kenichi Karatsu,
Akira Endo,
Jochem J. A. Baselmans,
Alejandro Pascual Laguna
Abstract:
Many superconducting on-chip filter-banks suffer from poor coupling to the detectors behind each filter. This is a problem intrinsic to the commonly used half wavelength filter, which has a maximum theoretical coupling of 50 %. In this paper we introduce a phase coherent filter, called a directional filter, which has a theoretical coupling of 100 %. In order to to study and compare different types…
▽ More
Many superconducting on-chip filter-banks suffer from poor coupling to the detectors behind each filter. This is a problem intrinsic to the commonly used half wavelength filter, which has a maximum theoretical coupling of 50 %. In this paper we introduce a phase coherent filter, called a directional filter, which has a theoretical coupling of 100 %. In order to to study and compare different types of filter-banks, we first analyze the measured filter frequency scatter, losses, and spectral resolution of a DESHIMA 2.0 filter-bank chip. Based on measured fabrication tolerances and losses, we adapt the input parameters for our circuit simulations, quantitatively reproducing the measurements. We find that the frequency scatter is caused by nanometer-scale line-width variations and that variances in the spectral resolution is caused by losses in the dielectric only. Finally, we include these realistic parameters in a full filter-bank model and simulate a wide range of spectral resolutions and oversampling values. For all cases the directional filter-bank has significantly higher coupling to the detectors than the half-wave resonator filter-bank. The directional filter eliminates the need to use oversampling as a method to improve the total efficiency, instead capturing nearly all the power remaining after dielectric losses.
△ Less
Submitted 17 April, 2024;
originally announced April 2024.
-
2023 Astrophotonics Roadmap: pathways to realizing multi-functional integrated astrophotonic instruments
Authors:
Nemanja Jovanovic,
Pradip Gatkine,
Narsireddy Anugu,
Rodrigo Amezcua-Correa,
Ritoban Basu Thakur,
Charles Beichman,
Chad Bender,
Jean-Philippe Berger,
Azzurra Bigioli,
Joss Bland-Hawthorn,
Guillaume Bourdarot,
Charles M. Bradford,
Ronald Broeke,
Julia Bryant,
Kevin Bundy,
Ross Cheriton,
Nick Cvetojevic,
Momen Diab,
Scott A. Diddams,
Aline N. Dinkelaker,
Jeroen Duis,
Stephen Eikenberry,
Simon Ellis,
Akira Endo,
Donald F. Figer
, et al. (55 additional authors not shown)
Abstract:
Photonics offer numerous functionalities that can be used to realize astrophotonic instruments. The most spectacular example to date is the ESO Gravity instrument at the Very Large Telescope in Chile. Integrated astrophotonic devices stand to offer critical advantages for instrument development, including extreme miniaturization, as well as integration, superior thermal and mechanical stabilizatio…
▽ More
Photonics offer numerous functionalities that can be used to realize astrophotonic instruments. The most spectacular example to date is the ESO Gravity instrument at the Very Large Telescope in Chile. Integrated astrophotonic devices stand to offer critical advantages for instrument development, including extreme miniaturization, as well as integration, superior thermal and mechanical stabilization owing to the small footprint, and high replicability offering cost savings. Numerous astrophotonic technologies have been developed to address shortcomings of conventional instruments to date, including for example the development of photonic lanterns, complex aperiodic fiber Bragg gratings, complex beam combiners to enable long baseline interferometry, and laser frequency combs for high precision spectral calibration of spectrometers. Despite these successes, the facility implementation of photonic solutions in astronomical instrumentation is currently limited because of (1) low throughputs from coupling to fibers, coupling fibers to chips, propagation and bend losses, device losses, etc, (2) difficulties with scaling to large channel count devices needed for large bandwidths and high resolutions, and (3) efficient integration of photonics with detectors, to name a few. In this roadmap, we identify 24 areas that need further development. We outline the challenges and advances needed across those areas covering design tools, simulation capabilities, fabrication processes, the need for entirely new components, integration and hybridization and the characterization of devices. To realize these advances the astrophotonics community will have to work cooperatively with industrial partners who have more advanced manufacturing capabilities. With the advances described herein, multi-functional instruments will be realized leading to novel observing capabilities for both ground and space platforms.
△ Less
Submitted 1 November, 2023;
originally announced November 2023.
-
Half-mirror for electrons on quantum Hall copropagating edge channels
Authors:
Takase Shimizu,
Jun-ichiro Ohe,
Akira Endo,
Taketomo Nakamura,
Shingo Katsumoto
Abstract:
A half-mirror that divides a spin-polarized electron into two parallel copropagating spin-resolved quantum Hall edge channels one half each is presented in this study. The partition process was coherent, as confirmed by observing the Aharonov-Bohm oscillation at a high visibility of up to 60% in a Mach-Zehnder interferometer, which comprised two such half-mirrors. The device characteristics were h…
▽ More
A half-mirror that divides a spin-polarized electron into two parallel copropagating spin-resolved quantum Hall edge channels one half each is presented in this study. The partition process was coherent, as confirmed by observing the Aharonov-Bohm oscillation at a high visibility of up to 60% in a Mach-Zehnder interferometer, which comprised two such half-mirrors. The device characteristics were highly stable, making the device promising in the application of quantum information processing. The beam-splitting process is theoretically modelled, and the numerical simulation successfully reproduces the experimental observation. The partition of the electron accompanied by the spin rotation is explained by the angular momentum transfer from the orbital to the spin via spin-orbit interactions.
△ Less
Submitted 14 September, 2022;
originally announced September 2022.
-
Superconducting Microstrip Losses at Microwave and Sub-millimeter wavelengths
Authors:
S. Hähnle,
K. Kouwenhoven,
B. Buijtendorp,
A. Endo,
K. Karatsu,
D. J. Thoen,
V. Murugesan,
J. J. A. Baselmans
Abstract:
We present a lab-on-chip experiment to accurately measure losses of superconducting microstrip lines at microwave and sub-mm wavelengths. The microstrips are fabricated from NbTiN, which is deposited using reactive magnetron sputtering, and amorphous silicon which is deposited using plasma-enhanced chemical vapor deposition (PECVD). Sub-mm wave losses are measured using on-chip Fabry-P{é}rot reson…
▽ More
We present a lab-on-chip experiment to accurately measure losses of superconducting microstrip lines at microwave and sub-mm wavelengths. The microstrips are fabricated from NbTiN, which is deposited using reactive magnetron sputtering, and amorphous silicon which is deposited using plasma-enhanced chemical vapor deposition (PECVD). Sub-mm wave losses are measured using on-chip Fabry-P{é}rot resonators (FPR) operating around $350\ $GHz. Microwave losses are measured using shunted half-wave resonators with an identical geometry and fabricated on the same chip. We measure a loss tangent of the amorphous silicon at single-photon energies of $\tanδ=3.7\pm0.5\times10^{-5}$ at $6\ $GHz and $\tanδ= 2.1\pm 0.1\times10^{-4}$ at $350\ $GHz. These results represent very low losses for deposited dielectrics, but the sub-mm wave losses are significantly higher than the microwave losses, which cannot be understood using the standard two-level system loss model.
△ Less
Submitted 25 August, 2021;
originally announced August 2021.
-
Reactive miscible displacement of light oil in porous media
Authors:
Max Endo Kokubun,
Negar Khoshnevis Gargar,
Dan Marchesin,
Hans Bruining
Abstract:
We develop a theory for the problem of high pressure air injection into deep reservoirs containing light oil. Under these conditions, the injected fluid (oxygen + inert components) is completely miscible with the oil in the reservoir. Moreover, exothermic reactions between dissolved oxygen and oil are possible. We use Koval's model to account for the miscibility of the components, such that the fr…
▽ More
We develop a theory for the problem of high pressure air injection into deep reservoirs containing light oil. Under these conditions, the injected fluid (oxygen + inert components) is completely miscible with the oil in the reservoir. Moreover, exothermic reactions between dissolved oxygen and oil are possible. We use Koval's model to account for the miscibility of the components, such that the fractional-flow functions resemble the ones from Buckley-Leverett flow. This allows to decompose the solution of this problem into a series of waves. We then proceed to obtain full analytical solutions in each wave. Of particular interest {is the case where} the combustion wave presents a singularity in its internal wave profile. Evaluation of the variables of the problem at the singular point determines the macroscopic parameters of the wave, i.e., combustion temperature, wave speed and downstream oil fraction. The waves structure was observed previously for reactive immiscible displacement and we describe it here for the first time for reactive miscible displacement of oil. We validate the developed theory using numerical simulations.
△ Less
Submitted 19 September, 2023; v1 submitted 28 September, 2020;
originally announced September 2020.
-
A generalized spray-flamelet formulation by means of a monotonic variable
Authors:
Daniela de Oliveira Maionchi,
Fabio Pereira dos Santos,
Josué Melguizo-Gavilanes,
Max Akira Endo Kokubun
Abstract:
The external structure of the spray-flamelet can be described using the Schvab-Zel'dovich-Liñan formulation. The gaseous mixture-fraction variable as function of the physical space, Z(x_i), typically employed for the description of gaseous diffusion flames leads to non-monotonicity behaviour for spray flames due to the extra fuel supplied by vaporisation of droplets distributed into the flow. As a…
▽ More
The external structure of the spray-flamelet can be described using the Schvab-Zel'dovich-Liñan formulation. The gaseous mixture-fraction variable as function of the physical space, Z(x_i), typically employed for the description of gaseous diffusion flames leads to non-monotonicity behaviour for spray flames due to the extra fuel supplied by vaporisation of droplets distributed into the flow. As a result, the overall properties of spray flames depend not only on Z and the scalar dissipation rate, but also on the spray source term, S_v. We propose a new general coordinate variable which takes into account the spatial information about the entire mixture fraction due to the gaseous phase and droplet vaporisation. This coordinate variable, Z_C(x_i) is based on the cumulative value of the gaseous mixture fraction Z(x_i), and is shown to be monotonic. For pure gaseous flow, the new cumulative function, Z_C, yields the well-established flamelet structure in Z-space. In the present manuscript, the spray-flamelet structure and the new equations for temperature and mass fractions in terms of Z_C are derived and then applied to the canonical counterflow configuration with potential flow. Numerical results are obtained for ethanol and methanol sprays, and the effect of Lewis and Stokes numbers on the spray-flamelet structure are analyzed. The proposed formulation agrees well when map** the structure back to physical space thereby confirming our integration methodology.
△ Less
Submitted 2 June, 2020;
originally announced June 2020.
-
Suppression of radiation loss in high kinetic inductance superconducting co-planar waveguides
Authors:
S. Hähnle,
N. v. Marrewijk,
A. Endo,
K. Karatsu,
D. J. Thoen,
V. Murugesan,
J. J. A. Baselmans
Abstract:
We present a novel lab-on-chip technique to measure the very low losses in superconducting transmission lines at (sub-) mm wavelengths. The chips consist of a 100 nm thick NbTiN Coplanar Waveguide (CPW) Fabry Perot (FP) resonator, coupled on one side to an antenna and on the other side to a Microwave Kinetic Inductance detector. Using a single frequency radiation source allows us to measure the fr…
▽ More
We present a novel lab-on-chip technique to measure the very low losses in superconducting transmission lines at (sub-) mm wavelengths. The chips consist of a 100 nm thick NbTiN Coplanar Waveguide (CPW) Fabry Perot (FP) resonator, coupled on one side to an antenna and on the other side to a Microwave Kinetic Inductance detector. Using a single frequency radiation source allows us to measure the frequency response of the FP around 350 GHz and deduce its losses. We show that the loss is dominated by radiation loss inside the CPW line that forms the FP and that it decreases with decreasing line width and increasing kinetic inductance as expected. The results can be quantitatively understood using SONNET simulations. The lowest loss is observed for a CPW with a total width of $6\ \mathrm{μm}$ and corresponds to a Q-factor of $\approx15,000$.
△ Less
Submitted 28 April, 2020; v1 submitted 23 March, 2020;
originally announced March 2020.
-
A pore-scale study of transport of inertial particles by water in porous media
Authors:
Max A. Endo Kokubun,
Adrian Muntean,
Florin A. Radu,
Kundan Kumar,
Iuliu S. Pop,
Eirik Keilegavlen,
Kristine Spildo
Abstract:
We study the transport of inertial particles in water flow in porous media. Our interest lies in understanding the accumulation of particles including the possibility of clogging. We propose that accumulation can be a result of hydrodynamic effects: the tortuous paths of the porous medium generate regions of dominating strain/vorticity, which favour the accumulation/dispersion of the inertial part…
▽ More
We study the transport of inertial particles in water flow in porous media. Our interest lies in understanding the accumulation of particles including the possibility of clogging. We propose that accumulation can be a result of hydrodynamic effects: the tortuous paths of the porous medium generate regions of dominating strain/vorticity, which favour the accumulation/dispersion of the inertial particles. Numerical simulations show that essentially two accumulation regimes are identified: for low and for high flow velocities. When particles accumulate in high-velocity regions, at the entrance of a pore throat, a clog is formed. The formation of a clog significantly modifies the flow, as the partial blockage of the pore causes a local redistribution of pressure. This redistribution can divert the upstream water flow into neighbouring pores. Moreover, we show that accumulation in high velocity regions occurs in heterogeneous media, but not in homogeneous media, where we refer to homogeneity with respect to the distribution of the pore throat diameters.
△ Less
Submitted 29 May, 2019; v1 submitted 21 February, 2019;
originally announced February 2019.
-
Mitigation of Cosmic Ray Effect on Microwave Kinetic Inductance Detector Arrays
Authors:
K. Karatsu,
A. Endo,
J. Bueno,
P. J. de Visser,
R. Barends,
D. J. Thoen,
V. Murugesan,
N. Tomita,
J. J. A. Baselmans
Abstract:
For space observatories, the glitches caused by high energy phonons created by the interaction of cosmic ray particles with the detector substrate lead to dead time during observation. Mitigating the impact of cosmic rays is therefore an important requirement for detectors to be used in future space missions. In order to investigate possible solutions, we carry out a systematic study by testing fo…
▽ More
For space observatories, the glitches caused by high energy phonons created by the interaction of cosmic ray particles with the detector substrate lead to dead time during observation. Mitigating the impact of cosmic rays is therefore an important requirement for detectors to be used in future space missions. In order to investigate possible solutions, we carry out a systematic study by testing four large arrays of Microwave Kinetic Inductance Detectors (MKIDs), each consisting of $\sim$960 pixels and fabricated on monolithic 55 mm $\times$ 55 mm $\times$ 0.35 mm Si substrates. We compare the response to cosmic ray interactions in our laboratory for different detector arrays: A standard array with only the MKID array as reference; an array with a low $T_c$ superconducting film as phonon absorber on the opposite side of the substrate; and arrays with MKIDs on membranes. The idea is that the low $T_c$ layer down-converts the phonon energy to values below the pair breaking threshold of the MKIDs, and the membranes isolate the sensitive part of the MKIDs from phonons created in the substrate. We find that the dead time can be reduced up to a factor of 40 when compared to the reference array. Simulations show that the dead time can be reduced to below 1 % for the tested detector arrays when operated in a spacecraft in an L2 or a similar far-Earth orbit. The technique described here is also applicable and important for large superconducting qubit arrays for future quantum computers.
△ Less
Submitted 10 January, 2019; v1 submitted 8 January, 2019;
originally announced January 2019.
-
Transport of polymer particles in a oil-water flow in porous media: enhancing oil recovery
Authors:
Max A. Endo Kokubun,
Florin A. Radu,
Eirik Keilegavlen,
Kundan Kumar,
Kristine Spildo
Abstract:
We study a heuristic, core-scale model for the transport of polymer particles in a two phase (oil and water) porous medium. We are motivated by recent experimental observations which report increased oil recovery when polymers are injected after the initial waterflood. The recovery mechanism is believed to be microscopic diversion of the flow, where injected particles can accumulate in narrow pore…
▽ More
We study a heuristic, core-scale model for the transport of polymer particles in a two phase (oil and water) porous medium. We are motivated by recent experimental observations which report increased oil recovery when polymers are injected after the initial waterflood. The recovery mechanism is believed to be microscopic diversion of the flow, where injected particles can accumulate in narrow pore throats and clog it, in a process known as a log-jamming effect. The blockage of the narrow pore channels lead to a microscopic diversion of the water flow, causing a redistribution of the local pressure, which again can lead to the mobilization of trapped oil, enhancing its recovery. Our objective herein is to develop a core-scale model that is consistent with the observed production profiles. We show that previously obtained experimental results can be qualitatively explained by a simple two-phase flow model with an additional transport equation for the polymer particles. A key aspect of the formulation is that the microscopic heterogeneity of the rock and a dynamic altering of the permeability must be taken into account in the rate equations.
△ Less
Submitted 15 February, 2018;
originally announced February 2018.
-
Singularity of a combustion wave profile: a clue to the multicomponent theory for liquid-gas filtration combustion
Authors:
Max Endo Kokubun,
Alexei Mailybaev
Abstract:
We study a nonlinear wave for a system of balance laws in one space dimension, which describes combustion for two-phase (gas and liquid) flow in porous medium. The problem is formulated for a general $N$-component liquid for modeling the strong multicomponent effects reported recently for an application to light oil recovery by air injection. Despite the immense complexity of the model, the proble…
▽ More
We study a nonlinear wave for a system of balance laws in one space dimension, which describes combustion for two-phase (gas and liquid) flow in porous medium. The problem is formulated for a general $N$-component liquid for modeling the strong multicomponent effects reported recently for an application to light oil recovery by air injection. Despite the immense complexity of the model, the problem allows analytic solution. The clue to this solution is a special form of a folding singularity, which occurs at an internal point of the wave profile. Analysis of this singularity provides a missing determining relation for wave parameters. This result is not only interesting for the application under consideration, but also motivates a deeper mathematical study of such singularities for general systems of balance laws.
△ Less
Submitted 24 August, 2017; v1 submitted 18 October, 2016;
originally announced October 2016.
-
Superconducting NbTiN Thin Films with Highly Uniform Properties over a 100 mm diameter Wafer
Authors:
D. J. Thoen,
B. G. C. Bos,
E. A. F. Haalebos,
T. M. Klapwijk,
J. J. A. Baselmans,
A. Endo
Abstract:
Uniformity in thickness and electronic properties of superconducting niobium titanium nitride (NbTiN) thin films is a critical issue for upscaling superconducting electronics, such as microwave kinetic inductance detectors for submillimeter wave astronomy. In this article we make an experimental comparison between the uniformity of NbTiN thin films produced by two DC magnetron sputtering systems w…
▽ More
Uniformity in thickness and electronic properties of superconducting niobium titanium nitride (NbTiN) thin films is a critical issue for upscaling superconducting electronics, such as microwave kinetic inductance detectors for submillimeter wave astronomy. In this article we make an experimental comparison between the uniformity of NbTiN thin films produced by two DC magnetron sputtering systems with vastly different target sizes: the Nordiko 2000 equipped with a circular 100mm diameter target, and the Evatec LLS801 with a rectangular target of 127 mm x 444.5 mm. In addition to the films deposited staticly in both systems, we have also deposited films in the LLS801 while shuttling the substrate in front of the target, with the aim of further enhancing the uniformity. Among these three setups, the LLS801 system with substrate shuttling has yielded the highest uniformity in film thickness (+/-2%), effective resistivity (decreasing by 5% from center to edge), and superconducting critical temperature (T_c = 15.0 K - 15.3 K) over a 100 mm diameter wafer. However, the shuttling appears to increase the resistivity by almost a factor of 2 compared to static deposition. Surface SEM inspections suggest that the shuttling could have induced a different mode of microstructural film growth.
△ Less
Submitted 22 November, 2016; v1 submitted 6 September, 2016;
originally announced September 2016.
-
Probing the Nuclear Spin-Lattice Relaxation Time at the Nanoscale
Authors:
J. J. T. Wagenaar,
A. M. J. den Haan,
J. M. de Voogd,
L. Bossoni,
T. A. de Jong,
M. de Wit,
K. M. Bastiaans,
D. J. Thoen,
A. Endo,
T. M. Klapwijk,
J. Zaanen,
T. H. Oosterkamp
Abstract:
Nuclear spin-lattice relaxation times are measured on copper using magnetic resonance force microscopy performed at temperatures down to 42 mK. The low temperature is verified by comparison with the Korringa relation. Measuring spin-lattice relaxation times locally at very low temperatures opens up the possibility to measure the magnetic properties of inhomogeneous electron systems realized in oxi…
▽ More
Nuclear spin-lattice relaxation times are measured on copper using magnetic resonance force microscopy performed at temperatures down to 42 mK. The low temperature is verified by comparison with the Korringa relation. Measuring spin-lattice relaxation times locally at very low temperatures opens up the possibility to measure the magnetic properties of inhomogeneous electron systems realized in oxide interfaces, topological insulators and other strongly correlated electron systems such as high-Tc superconductors.
△ Less
Submitted 27 June, 2016; v1 submitted 14 March, 2016;
originally announced March 2016.
-
Performance of Hybrid NbTiN-Al Microwave Kinetic Inductance Detectors as Direct Detectors for Sub-millimeter Astronomy
Authors:
R. M. J. Janssen,
J. J. A. Baselmans,
A. Endo,
L. Ferrari,
S. J. C. Yates,
A. M. Baryshev,
T. M. Klapwijk
Abstract:
In the next decades millimeter and sub-mm astronomy requires large format imaging arrays and broad-band spectrometers to complement the high spatial and spectral resolution of the Atacama Large Millimeter/sub-millimeter Array. The desired sensors for these instruments should have a background limited sensitivity and a high optical efficiency and enable arrays thousands of pixels in size. Hybrid mi…
▽ More
In the next decades millimeter and sub-mm astronomy requires large format imaging arrays and broad-band spectrometers to complement the high spatial and spectral resolution of the Atacama Large Millimeter/sub-millimeter Array. The desired sensors for these instruments should have a background limited sensitivity and a high optical efficiency and enable arrays thousands of pixels in size. Hybrid microwave kinetic inductance detectors consisting of NbTiN and Al have shown to satisfy these requirements. We present the second generation hybrid NbTiN-Al MKIDs, which are photon noise limited in both phase and amplitude readout for loading levels $P_{850GHz} \geq 10$ fW. Thanks to the increased responsivity, the photon noise level achieved in phase allows us to simultaneously read out approximately 8000 pixels using state-of-the-art electronics. In addition, the choice of superconducting materials and the use of a Si lens in combination with a planar antenna gives these resonators the flexibility to operate within the frequency range $0.09 < ν< 1.1$ THz. Given these specifications, hybrid NbTiN-Al MKIDs will enable astronomically usable kilopixel arrays for sub-mm imaging and moderate resolution spectroscopy.
△ Less
Submitted 14 August, 2014;
originally announced August 2014.
-
Equivalence of Optical and Electrical Noise Equivalent Power of Hybrid NbTiN-Al Microwave Kinetic Inductance Detectors
Authors:
R. M. J. Janssen,
A. Endo,
P. J. de Visser,
T. M. Klapwijk,
J. J. A. Baselmans
Abstract:
We have measured and compared the response of hybrid NbTiN-Al Microwave Kinetic Inductance Detectors (MKIDs) to changes in bath temperature and illumination by sub-mm radiation. We show that these two stimulants have an equivalent effect on the resonance feature of hybrid MKIDs. We determine an electrical NEP from the measured temperature responsivity, quasiparticle recombination time, superconduc…
▽ More
We have measured and compared the response of hybrid NbTiN-Al Microwave Kinetic Inductance Detectors (MKIDs) to changes in bath temperature and illumination by sub-mm radiation. We show that these two stimulants have an equivalent effect on the resonance feature of hybrid MKIDs. We determine an electrical NEP from the measured temperature responsivity, quasiparticle recombination time, superconducting transition temperature and noise spectrum, all of which can be measured in a dark environment. For the two hybrid NbTiN-Al MKIDs studied in detail the electrical NEP is within a factor of two of the optical NEP, which is measured directly using a blackbody source.
△ Less
Submitted 17 November, 2014; v1 submitted 14 August, 2014;
originally announced August 2014.
-
High optical efficiency and photon noise limited sensitivity of microwave kinetic inductance detectors using phase readout
Authors:
R. M. J. Janssen,
J. J. A. Baselmans,
A. Endo,
L. Ferrari,
S. J. C. Yates,
A. M. Baryshev,
T. M. Klapwijk
Abstract:
We demonstrate photon noise limited performance in both phase and amplitude readout in microwave kinetic inductance detectors (MKIDs) consisting of NbTiN and Al, down to 100 fW of optical power. We simulate the far field beam pattern of the lens-antenna system used to couple radiation into the MKID and derive an aperture efficiency of 75%. This is close to the theoretical maximum of 80% for a sing…
▽ More
We demonstrate photon noise limited performance in both phase and amplitude readout in microwave kinetic inductance detectors (MKIDs) consisting of NbTiN and Al, down to 100 fW of optical power. We simulate the far field beam pattern of the lens-antenna system used to couple radiation into the MKID and derive an aperture efficiency of 75%. This is close to the theoretical maximum of 80% for a single-moded detector. The beam patterns are verified by a detailed analysis of the optical coupling within our measurement setup.
△ Less
Submitted 11 November, 2013;
originally announced November 2013.
-
Power Handling and Responsivity of Submicron Wide Superconducting Coplanar Waveguide Resonators
Authors:
R. M. J. Janssen,
A. Endo,
J. J. A. Baselmans,
P. J. de Visser,
R. Barends,
T. M. Klapwijk
Abstract:
The sensitivity of microwave kinetic inductance detectors (MKIDs) based on coplanar waveguides (CPWs) needs to be improved by at least an order of magnitude to satisfy the requirements for space-based terahertz astronomy. Our aim is to investigate if this can be achieved by reducing the width of the CPW to much below what has typically been made using optical lithography (> 1 μm). CPW resonators w…
▽ More
The sensitivity of microwave kinetic inductance detectors (MKIDs) based on coplanar waveguides (CPWs) needs to be improved by at least an order of magnitude to satisfy the requirements for space-based terahertz astronomy. Our aim is to investigate if this can be achieved by reducing the width of the CPW to much below what has typically been made using optical lithography (> 1 μm). CPW resonators with a central line width as narrow as 300 nm were made in NbTiN using electron beam lithography and reactive ion etching. In a systematic study of quarter-wave CPW resonators with varying widths it is shown that the behavior of responsivity, noise and power handling as a function of width continues down to 300 nm. This encourages the development of narrow KIDs using Al in order to improve their sensitivity.
△ Less
Submitted 4 June, 2012;
originally announced June 2012.
-
A dual-band millimeter-wave kinetic inductance camera for the IRAM 30-meter telescope
Authors:
A. Monfardini,
A. Benoit,
A. Bideaud,
L. J. Swenson,
M. Roesch,
F. X. Desert,
S. Doyle,
A. Endo,
A. Cruciani,
P. Ade,
A. M. Baryshev,
J. J. A. Baselmans,
O. Bourrion,
M. Calvo,
P. Camus,
L. Ferrari,
C. Giordano,
C. Hoffmann,
S. Leclercq,
J. F. Macias-Perez,
P. Mauskopf,
K. F. Schuster,
C. Tucker,
C. Vescovi,
S. J. C. Yates
Abstract:
Context. The Neel IRAM KIDs Array (NIKA) is a fully-integrated measurement system based on kinetic inductance detectors (KIDs) currently being developed for millimeter wave astronomy. In a first technical run, NIKA was successfully tested in 2009 at the Institute for Millimetric Radio Astronomy (IRAM) 30-meter telescope at Pico Veleta, Spain. This prototype consisted of a 27-42 pixel camera imagin…
▽ More
Context. The Neel IRAM KIDs Array (NIKA) is a fully-integrated measurement system based on kinetic inductance detectors (KIDs) currently being developed for millimeter wave astronomy. In a first technical run, NIKA was successfully tested in 2009 at the Institute for Millimetric Radio Astronomy (IRAM) 30-meter telescope at Pico Veleta, Spain. This prototype consisted of a 27-42 pixel camera imaging at 150 GHz. Subsequently, an improved system has been developed and tested in October 2010 at the Pico Veleta telescope. The instrument upgrades included dual-band optics allowing simultaneous imaging at 150 GHz and 220 GHz, faster sampling electronics enabling synchronous measurement of up to 112 pixels per measurement band, improved single-pixel sensitivity, and the fabrication of a sky simulator to replicate conditions present at the telescope. Results. The new dual-band NIKA was successfully tested in October 2010, performing in-line with sky simulator predictions. Initially the sources targeted during the 2009 run were re-imaged, verifying the improved system performance. An optical NEP was then calculated to be around 2 \dot 10-16 W/Hz1/2. This improvement in comparison with the 2009 run verifies that NIKA is approaching the target sensitivity for photon-noise limited ground-based detectors. Taking advantage of the larger arrays and increased sensitivity, a number of scientifically-relevant faint and extended objects were then imaged including the Galactic Center SgrB2(FIR1), the radio galaxy Cygnus A and the NGC1068 Seyfert galaxy. These targets were all observed simultaneously in the 150 GHz and 220 GHz atmospheric windows.
△ Less
Submitted 8 February, 2011; v1 submitted 4 February, 2011;
originally announced February 2011.
