-
Improving Computational Efficiency in DSMC Simulations of Vacuum Gas Dynamics with a Fixed Number of Particles per Cell
Authors:
Moslem Sabouri,
Ramin Zakeri,
Amin Ebrahimi
Abstract:
The present study addresses the challenge of enhancing computational efficiency without compromising accuracy in numerical simulations of vacuum gas dynamics using the direct simulation Monte Carlo (DSMC) method. A technique termed "fixed particle per cell (FPPC)" was employed, which enforces a fixed number of simulator particles across all computational cells. The proposed technique eliminates th…
▽ More
The present study addresses the challenge of enhancing computational efficiency without compromising accuracy in numerical simulations of vacuum gas dynamics using the direct simulation Monte Carlo (DSMC) method. A technique termed "fixed particle per cell (FPPC)" was employed, which enforces a fixed number of simulator particles across all computational cells. The proposed technique eliminates the need for real-time adjustment of particle weights during simulation, reducing calculation time. Using the SPARTA solver, simulations of rarefied gas flow in a micromixer and rarefied supersonic airflow around a cylinder were conducted to validate the proposed technique. Results demonstrate that applying the FPPC technique effectively reduces computational costs while yielding results comparable to conventional DSMC implementations. Additionally, the application of local grid refinement coupled with the FPPC technique was investigated. The results show that integrating local grid refinement with the FPPC technique enables accurate prediction of flow behaviour in regions with significant gradients. These findings highlight the efficacy of the proposed technique in improving the accuracy and efficiency of numerical simulations of complex vacuum gas dynamics at a reduced computational cost.
△ Less
Submitted 22 June, 2024;
originally announced July 2024.
-
Shower Separation in Five Dimensions for Highly Granular Calorimeters using Machine Learning
Authors:
S. Lai,
J. Utehs,
A. Wilhahn,
M. C. Fouz,
O. Bach,
E. Brianne,
A. Ebrahimi,
K. Gadow,
P. Göttlicher,
O. Hartbrich,
D. Heuchel,
A. Irles,
K. Krüger,
J. Kvasnicka,
S. Lu,
C. Neubüser,
A. Provenza,
M. Reinecke,
F. Sefkow,
S. Schuwalow,
M. De Silva,
Y. Sudo,
H. L. Tran,
L. Liu,
R. Masuda
, et al. (26 additional authors not shown)
Abstract:
To achieve state-of-the-art jet energy resolution for Particle Flow, sophisticated energy clustering algorithms must be developed that can fully exploit available information to separate energy deposits from charged and neutral particles. Three published neural network-based shower separation models were applied to simulation and experimental data to measure the performance of the highly granular…
▽ More
To achieve state-of-the-art jet energy resolution for Particle Flow, sophisticated energy clustering algorithms must be developed that can fully exploit available information to separate energy deposits from charged and neutral particles. Three published neural network-based shower separation models were applied to simulation and experimental data to measure the performance of the highly granular CALICE Analogue Hadronic Calorimeter (AHCAL) technological prototype in distinguishing the energy deposited by a single charged and single neutral hadron for Particle Flow. The performance of models trained using only standard spatial and energy and charged track position information from an event was compared to models trained using timing information available from AHCAL, which is expected to improve sensitivity to shower development and, therefore, aid in clustering. Both simulation and experimental data were used to train and test the models and their performances were compared. The best-performing neural network achieved significantly superior event reconstruction when timing information was utilised in training for the case where the charged hadron had more energy than the neutral one, motivating temporally sensitive calorimeters. All models under test were observed to tend to allocate energy deposited by the more energetic of the two showers to the less energetic one. Similar shower reconstruction performance was observed for a model trained on simulation and applied to data and a model trained and applied to data.
△ Less
Submitted 28 June, 2024;
originally announced July 2024.
-
Software Compensation for Highly Granular Calorimeters using Machine Learning
Authors:
S. Lai,
J. Utehs,
A. Wilhahn,
O. Bach,
E. Brianne,
A. Ebrahimi,
K. Gadow,
P. Göttlicher,
O. Hartbrich,
D. Heuchel,
A. Irles,
K. Krüger,
J. Kvasnicka,
S. Lu,
C. Neubüser,
A. Provenza,
M. Reinecke,
F. Sefkow,
S. Schuwalow,
M. De Silva,
Y. Sudo,
H. L. Tran,
E. Buhmann,
E. Garutti,
S. Huck
, et al. (39 additional authors not shown)
Abstract:
A neural network for software compensation was developed for the highly granular CALICE Analogue Hadronic Calorimeter (AHCAL). The neural network uses spatial and temporal event information from the AHCAL and energy information, which is expected to improve sensitivity to shower development and the neutron fraction of the hadron shower. The neural network method produced a depth-dependent energy w…
▽ More
A neural network for software compensation was developed for the highly granular CALICE Analogue Hadronic Calorimeter (AHCAL). The neural network uses spatial and temporal event information from the AHCAL and energy information, which is expected to improve sensitivity to shower development and the neutron fraction of the hadron shower. The neural network method produced a depth-dependent energy weighting and a time-dependent threshold for enhancing energy deposits consistent with the timescale of evaporation neutrons. Additionally, it was observed to learn an energy-weighting indicative of longitudinal leakage correction. In addition, the method produced a linear detector response and outperformed a published control method regarding resolution for every particle energy studied.
△ Less
Submitted 7 March, 2024;
originally announced March 2024.
-
Revealing the effects of laser beam sha** on melt pool behaviour in conduction-mode laser melting
Authors:
Amin Ebrahimi,
Mohammad Sattari,
Aravind Babu,
Arjun Sood,
Gert-willem Römer,
Marcel Hermans
Abstract:
Laser beam sha** offers remarkable possibilities to control and optimise process stability and tailor material properties and structure in laser-based welding and additive manufacturing. However, little is known about the influence of laser beam sha** on the complex melt-pool behaviour, solidified melt-track bead profile and microstructural grain morphology in laser material processing. A simu…
▽ More
Laser beam sha** offers remarkable possibilities to control and optimise process stability and tailor material properties and structure in laser-based welding and additive manufacturing. However, little is known about the influence of laser beam sha** on the complex melt-pool behaviour, solidified melt-track bead profile and microstructural grain morphology in laser material processing. A simulation-based approach is utilised in the present work to study the effects of laser beam intensity profile and angle of incidence on the melt-pool behaviour in conduction-mode laser melting of stainless steel 316L plates. The present high-fidelity physics-based computational model accounts for crucial physical phenomena in laser material processing such as complex laser-matter interaction, solidification and melting, heat and fluid flow dynamics, and free-surface oscillations. Experiments were carried out using different laser beam shapes and the validity of the numerical predictions is demonstrated. The results indicate that for identical processing parameters, resha** the laser beam leads to notable changes in the thermal and fluid flow fields in the melt pool, affecting the melt-track bead profile and solidification microstructure. The columnar-to-equiaxed transition is discussed for different laser-intensity profiles.
△ Less
Submitted 12 November, 2023;
originally announced November 2023.
-
Computational Study of Rarefied Gas Flow and Heat Transfer in Lid-driven Cylindrical Cavities
Authors:
Mengbo Zhu,
Ehsan Roohi,
Amin Ebrahimi
Abstract:
The gas flow characteristics in lid-driven cavities are influenced by several factors, such as cavity geometry, gas properties, and boundary conditions. In this study, the physics of heat and gas flow in cylindrical lid-driven cavities with various cross-sections, including fully or partially rounded edges, is investigated through numerical simulations using the direct simulation Monte Carlo (DSMC…
▽ More
The gas flow characteristics in lid-driven cavities are influenced by several factors, such as cavity geometry, gas properties, and boundary conditions. In this study, the physics of heat and gas flow in cylindrical lid-driven cavities with various cross-sections, including fully or partially rounded edges, is investigated through numerical simulations using the direct simulation Monte Carlo (DSMC) and the discrete unified gas kinetic scheme (DUGKS) methods. The thermal and fluid flow fields are systematically studied for both constant and oscillatory lid velocities, for various degrees of gas rarefaction ranging from the slip to the free-molecular regimes. The impact of expansion cooling and viscous dissipation on the thermal and flow fields, as well as the occurrence of counter-gradient heat transfer (also known as anti-Fourier heat transfer) under non-equilibrium conditions, are explained based on the results obtained from numerical simulations. Furthermore, the influence of the incomplete tangential accommodation coefficient on the thermal and fluid flow fields is discussed. A comparison is made between the thermal and fluid flow fields predicted in cylindrical cavities and those in square-shaped cavities. The present work contributes to the advancement of micro/nano-electromechanical systems (MEMS/NEMS) by providing valuable insights into rarefied gas flow and heat transfer in lid-driven cavities.
△ Less
Submitted 16 May, 2023;
originally announced June 2023.
-
The Effect of Groove Shape on Molten Metal Flow Behaviour in Gas Metal Arc Welding
Authors:
Amin Ebrahimi,
Aravind Babu,
Chris R. Kleijn,
Marcel J. M. Hermans,
Ian M. Richardson
Abstract:
One of the challenges for development, qualification and optimisation of arc welding processes lies in characterising the complex melt-pool behaviour which exhibits highly non-linear responses to variations of process parameters. The present work presents a simulation-based approach to describe the melt-pool behaviour in root-pass gas metal arc welding (GMAW). Three-dimensional numerical simulatio…
▽ More
One of the challenges for development, qualification and optimisation of arc welding processes lies in characterising the complex melt-pool behaviour which exhibits highly non-linear responses to variations of process parameters. The present work presents a simulation-based approach to describe the melt-pool behaviour in root-pass gas metal arc welding (GMAW). Three-dimensional numerical simulations have been performed using an enhanced physics-based computational model to unravel the effect of groove shape on complex unsteady heat and fluid flow in GMAW. The influence of surface deformations on power-density distribution and the forces applied to the molten material was taken into account. Utilising this model, the complex heat and fluid flow in melt pools were visualised and described for different groove shapes. Additionally, experiments were performed to validate the numerical predictions and the robustness of the present computational model is demonstrated. The model can be used to explore physical effects of governing fluid flow and melt-pool stability during gas metal arc root welding.
△ Less
Submitted 13 December, 2021;
originally announced January 2022.
-
The influence of laser characteristics on internal flow behaviour in laser melting of metallic substrates
Authors:
Amin Ebrahimi,
Mohammad Sattari,
Scholte J. L. Bremer,
Martin Luckabauer,
Gert-willem R. B. E. Römer,
Ian M. Richardson,
Chris R. Kleijn,
Marcel J. M. Hermans
Abstract:
The absorptivity of a material is a major uncertainty in numerical simulations of laser welding and additive manufacturing, and its value is often calibrated through trial-and-error exercises. This adversely affects the capability of numerical simulations when predicting the process behaviour and can eventually hinder the exploitation of fully digitised manufacturing processes, which is a goal of…
▽ More
The absorptivity of a material is a major uncertainty in numerical simulations of laser welding and additive manufacturing, and its value is often calibrated through trial-and-error exercises. This adversely affects the capability of numerical simulations when predicting the process behaviour and can eventually hinder the exploitation of fully digitised manufacturing processes, which is a goal of "industry 4.0". In the present work, an enhanced absorption model that takes into account the effects of laser characteristics, incident angle, surface temperature, and material composition is utilised to predict internal heat and fluid flow in laser melting of stainless steel 316L. Employing such an absorption model is physically more realistic than assuming a constant absorptivity and can reduce the costs associated with calibrating an appropriate value. High-fidelity three-dimensional numerical simulations were performed using both variable and constant absorptivity models and the predictions compared with experimental data. The results of the present work unravel the crucial effect of absorptivity on the physics of internal flow in laser material processing. The difference between melt-pool shapes obtained using fibre and CO$_2$ laser sources is explained, and factors affecting the local energy absorption are discussed.
△ Less
Submitted 5 January, 2022;
originally announced January 2022.
-
Depth-dependent charge collection profile of pad diodes
Authors:
Mohammadtaghi Hajheidari,
Erika Garutti,
Joern Schwandt,
Aliakbar Ebrahimi
Abstract:
The collected charge of two pad diodes is measured along the diode width using a 5:2 GeV electron beam at the DESY II beam test facility. The electron beam enters parallel to the readout electrode plane and perpendicular to the edge of the diode. The position of the electron beam is reconstructed by three planes of an EUDET-type telescope. An in-situ procedure is developed to align the diode surfa…
▽ More
The collected charge of two pad diodes is measured along the diode width using a 5:2 GeV electron beam at the DESY II beam test facility. The electron beam enters parallel to the readout electrode plane and perpendicular to the edge of the diode. The position of the electron beam is reconstructed by three planes of an EUDET-type telescope. An in-situ procedure is developed to align the diode surface parallel to the electron beam. The result of these measurements is the charge collection efficiency profile as a function of depth for each diode. For a non-irradiated diode, the charge profile is uniform as a function of the beam position for bias voltages above the full-depletion, as expected. For the irradiated diode, the charge profile is non-uniform and changes as a function of bias voltage.
△ Less
Submitted 15 December, 2021; v1 submitted 7 August, 2021;
originally announced August 2021.
-
Position reconstruction for segmented detectors
Authors:
A. Ebrahimi,
F. Feind,
E. Fretwurst,
E. Garutti,
M. Hajheidari,
R. Klanner,
D. Pitzl,
J. Schwandt,
G. Steinbrueck,
I. Zoi
Abstract:
The topic of the paper is the position reconstruction from signals of segmented detectors. With the help of a simple simulation, it is shown that the position reconstruction using the centre-of-gravity method is strongly biased, if the width of the charge (or e.g. light) distribution at the electrodes (or photo detectors) is less than the read-out pitch. A method is proposed which removes this bia…
▽ More
The topic of the paper is the position reconstruction from signals of segmented detectors. With the help of a simple simulation, it is shown that the position reconstruction using the centre-of-gravity method is strongly biased, if the width of the charge (or e.g. light) distribution at the electrodes (or photo detectors) is less than the read-out pitch. A method is proposed which removes this bias for events with signals in two or more read-out channels and thereby improves the position resolution. The method also provides an estimate of the position-response function for every event. Examples are given for which its width as a function of the reconstructed position varies by as much as an order of magnitude.
A fast Monte Carlo program is described which simulates the signals from a silicon pixel detector traversed by charged particles under different angles, and the results obtained with the proposed reconstruction method and with the centre-of-gravity method are compared. The simulation includes the local energy-loss fluctuations, the position-dependent electric field, the diffusion of the charge carriers, the electronics noise and charge thresholds for clustering. A comparison to test-beam-data is used to validate the simulation.
△ Less
Submitted 14 July, 2021;
originally announced July 2021.
-
Position resolution with 25 um pitch pixel sensors before and after irradiation
Authors:
I. Zoi,
A. Ebrahimi,
F. Feindt,
E. Garutti,
P. Gunnellini,
A. Hinzmann,
C. Niemeyer,
D. Pitzl,
J. Schwandt,
G. Steinbrück
Abstract:
Pixelated silicon detectors are state-of-the-art technology to achieve precise tracking and vertexing at collider experiments, designed to accurately measure the hit position of incoming particles in high rate and radiation environments. The detector requirements become extremely demanding for operation at the High-Luminosity LHC, where up to 200 interactions will overlap in the same bunch crossin…
▽ More
Pixelated silicon detectors are state-of-the-art technology to achieve precise tracking and vertexing at collider experiments, designed to accurately measure the hit position of incoming particles in high rate and radiation environments. The detector requirements become extremely demanding for operation at the High-Luminosity LHC, where up to 200 interactions will overlap in the same bunch crossing on top of the process of interest. Additionally, fluences up to 2.3 10^16 cm^-2 1 MeV neutron equivalent at 3.0 cm distance from the beam are expected for an integrated luminosity of 3000 fb^-1. In the last decades, the pixel pitch has constantly been reduced to cope with the experiment's needs of achieving higher position resolution and maintaining low pixel occupancy per channel. The spatial resolution improves with a decreased pixel size but it degrades with radiation damage. Therefore, prototype sensor modules for the upgrade of the experiments at the HL-LHC need to be tested after being irradiated. This paper describes position resolution measurements on planar prototype sensors with 100x25 um^2 pixels for the CMS Phase-2 Upgrade. It reviews the dependence of the position resolution on the relative inclination angle between the incoming particle trajectory and the sensor, the charge threshold applied by the readout chip, and the bias voltage. A precision setup with three parallel planes of sensors has been used to investigate the performance of sensors irradiated to fluences up to F_eq = 3.6 10^15 cm-2. The measurements were performed with a 5 GeV electron beam. A spatial resolution of 3.2 +\- 0.1 um is found for non-irradiated sensors, at the optimal angle for charge sharing. The resolution is 5.0 +/- 0.2 um for a proton-irradiated sensor at F_eq = 2.1 10^15 cm-2 and a neutron-irradiated sensor at F_eq = 3.6 10^15 cm^-2.
△ Less
Submitted 9 July, 2021;
originally announced July 2021.
-
Pressure-driven Nitrogen Flow in Divergent Microchannels with Isothermal Walls
Authors:
Amin Ebrahimi,
Vahid Shahabi,
Ehsan Roohi
Abstract:
Gas flow and heat transfer in confined geometries at micro and nano scales differ considerably from those at macro-scales, mainly due to nonequilibrium effects such as velocity slip and temperature jump. The nonequilibrium effects enhance with a decrease in the characteristic length-scale of the fluid flow or the gas density, leading to the failure of the standard Navier-Stokes-Fourier (NSF) equat…
▽ More
Gas flow and heat transfer in confined geometries at micro and nano scales differ considerably from those at macro-scales, mainly due to nonequilibrium effects such as velocity slip and temperature jump. The nonequilibrium effects enhance with a decrease in the characteristic length-scale of the fluid flow or the gas density, leading to the failure of the standard Navier-Stokes-Fourier (NSF) equations in predicting thermal and fluid flow fields. The direct simulation Monte-Carlo (DSMC) method is employed in the present work to investigate pressure-driven nitrogen flow in divergent microchannels with various divergence angles and isothermal walls. The thermal fields obtained from numerical simulations are analysed for different inlet-to-outlet pressure ratios (1.5 $\leq Π\leq$ 2.5), tangential momentum accommodation coefficients and Knudsen numbers (0.05 $\leq \mathrm{Kn} \leq$ 12.5), covering slip to free-molecular rarefaction regimes. The thermal field in the microchannel is predicted, heat-lines are visualised, and the physics of heat transfer in the microchannel is discussed. Due to the rarefaction effects, the direction of heat flow is largely opposite to that of the mass flow. However, the interplay between thermal and pressure gradients, which are affected by geometrical configurations of the microchannel and applied boundary conditions, determines the net heat flow direction. Additionally, the occurrence of thermal separation and cold-to-hot heat transfer (also known as anti-Fourier heat transfer) in divergent microchannels is explained.
△ Less
Submitted 14 April, 2021;
originally announced April 2021.
-
The Effects of Process Parameters on Melt-pool Oscillatory Behaviour in Gas Tungsten Arc Welding
Authors:
Amin Ebrahimi,
Chris R. Kleijn,
Marcel J. M. Hermans,
Ian M. Richardson
Abstract:
Internal flow behaviour and melt-pool surface oscillations during arc welding are complex and not yet fully understood. In the present work, high-fidelity numerical simulations are employed to describe the effects of welding position, sulphur concentration (60-300 ppm) and travel speed (1.25-5 mm/s) on molten metal flow dynamics in fully-penetrated melt-pools. A wavelet transform is implemented to…
▽ More
Internal flow behaviour and melt-pool surface oscillations during arc welding are complex and not yet fully understood. In the present work, high-fidelity numerical simulations are employed to describe the effects of welding position, sulphur concentration (60-300 ppm) and travel speed (1.25-5 mm/s) on molten metal flow dynamics in fully-penetrated melt-pools. A wavelet transform is implemented to obtain time-resolved frequency spectra of the oscillation signals, which overcomes the shortcomings of the Fourier transform in rendering time resolution of the frequency spectra. Comparing the results of the present numerical calculations with available analytical and experimental datasets, the robustness of the proposed approach in predicting melt-pool oscillations is demonstrated. The results reveal that changes in the surface morphology of the pool resulting from a change in welding position alter the spatial distribution of arc forces and power-density applied to the molten material, and in turn affect flow patterns in the pool. Under similar welding conditions, changing the sulphur concentration affects the Marangoni flow pattern, and increasing the travel speed decreases the size of the pool and increases the offset between top and bottom melt-pool surfaces, affecting the flow structures (vortex formation) on the surface. Variations in the internal flow pattern affect the evolution of melt-pool shape and its surface oscillations.
△ Less
Submitted 6 April, 2021;
originally announced April 2021.
-
Numerical Study of Molten Metal Melt Pool Behaviour during Conduction-mode Laser Spot Melting
Authors:
Amin Ebrahimi,
Chris R. Kleijn,
Ian M. Richardson
Abstract:
Molten metal melt pools are characterised by highly non-linear responses, which are very sensitive to imposed boundary conditions. Temporal and spatial variations in the energy flux distribution are often neglected in numerical simulations of melt pool behaviour. Additionally, thermo-physical properties of materials are commonly changed to achieve agreement between predicted melt-pool shape and ex…
▽ More
Molten metal melt pools are characterised by highly non-linear responses, which are very sensitive to imposed boundary conditions. Temporal and spatial variations in the energy flux distribution are often neglected in numerical simulations of melt pool behaviour. Additionally, thermo-physical properties of materials are commonly changed to achieve agreement between predicted melt-pool shape and experimental post-solidification macrograph. Focusing on laser spot melting in conduction mode, we investigated the influence of dynamically adjusted energy flux distribution and changing thermo-physical material properties on melt pool oscillatory behaviour using both deformable and non-deformable assumptions for the gas-metal interface. Our results demonstrate that adjusting the absorbed energy flux affects the oscillatory fluid flow behaviour in the melt pool and consequently the predicted melt-pool shape and size. We also show that changing the thermophysical material properties artificially or using a non-deformable surface assumption lead to significant differences in melt pool oscillatory behaviour compared to the cases in which these assumptions are not made.
△ Less
Submitted 14 November, 2020;
originally announced November 2020.
-
The influence of surface deformation on thermocapillary flow instabilities in low Prandtl melting pools with surfactants
Authors:
Amin Ebrahimi,
Chris R. Kleijn,
Ian M. Richardson
Abstract:
Heat and fluid flow in low Prandtl number melting pools during laser processing of materials are sensitive to the prescribed boundary conditions, and the responses are highly nonlinear. Previous studies have shown that fluid flow in melt pools with surfactants can be unstable at high Marangoni numbers. In numerical simulations of molten metal flow in melt pools, surface deformations and its influe…
▽ More
Heat and fluid flow in low Prandtl number melting pools during laser processing of materials are sensitive to the prescribed boundary conditions, and the responses are highly nonlinear. Previous studies have shown that fluid flow in melt pools with surfactants can be unstable at high Marangoni numbers. In numerical simulations of molten metal flow in melt pools, surface deformations and its influence on the energy absorbed by the material are often neglected. However, this simplifying assumption may reduce the level of accuracy of numerical predictions with surface deformations. In the present study, we carry out three-dimensional numerical simulations to realise the effects of surface deformations on thermocapillary flow instabilities in laser melting of a metallic alloy with surfactants. Our computational model is based on the finite-volume method and utilises the volume-of-fluid (VOF) method for gas-metal interface tracking. Additionally, we employ a dynamically adjusted heat source model and discuss its influence on numerical predictions of the melt pool behaviour. Our results demonstrate that including free surface deformations in numerical simulations enhances the predicted flow instabilities and, thus, the predicted solid-liquid interface morphologies.
△ Less
Submitted 24 September, 2020;
originally announced September 2020.
-
Sensitivity of Numerical Predictions to the Permeability Coefficient in Simulations of Melting and Solidification Using the Enthalpy-Porosity Method
Authors:
Amin Ebrahimi,
Chris R. Kleijn,
Ian M. Richardson
Abstract:
The high degree of uncertainty and conflicting literature data on the value of the permeability coefficient (also known as the mushy zone constant), which aims to dampen fluid velocities in the mushy zone and suppress them in solid regions, is a critical drawback when using the fixed-grid enthalpy-porosity technique for modelling non-isothermal phase-change processes. In the present study, the sen…
▽ More
The high degree of uncertainty and conflicting literature data on the value of the permeability coefficient (also known as the mushy zone constant), which aims to dampen fluid velocities in the mushy zone and suppress them in solid regions, is a critical drawback when using the fixed-grid enthalpy-porosity technique for modelling non-isothermal phase-change processes. In the present study, the sensitivity of numerical predictions to the value of this coefficient was scrutinised. Using finite-volume based numerical simulations of isothermal and non-isothermal melting and solidification problems, the causes of increased sensitivity were identified. It was found that depending on the mushy-zone thickness and the velocity field, the solid-liquid interface morphology and the rate of phase-change are sensitive to the permeability coefficient. It is demonstrated that numerical predictions of an isothermal phase-change problem are independent of the permeability coefficient for sufficiently fine meshes. It is also shown that sensitivity to the choice of permeability coefficient can be assessed by means of an appropriately defined Péclet number.
△ Less
Submitted 25 April, 2020;
originally announced April 2020.
-
Solidification Characteristics of Laser-Powder Bed Fused AlSi10Mg: Role of Building Direction
Authors:
Hossein Azizi,
Alireza Ebrahimi,
Nana Ofori-Opoku,
Michael Greenwood,
Nikolas Provatas,
Mohsen Mohammadi
Abstract:
In this work, the effect of building direction on the microstructure evolution of laser-powder bed fusion (LPBF) processed AlSi10Mg alloy was investigated. The building direction, as shown in experimentally fabricated parts, can influence the solidification behavior and promote morphological transitions in cellular dendritic microstructures. We develop a thermal model to systemically address the i…
▽ More
In this work, the effect of building direction on the microstructure evolution of laser-powder bed fusion (LPBF) processed AlSi10Mg alloy was investigated. The building direction, as shown in experimentally fabricated parts, can influence the solidification behavior and promote morphological transitions in cellular dendritic microstructures. We develop a thermal model to systemically address the impact of laser processing conditions, and building direction on the thermal characteristics of the molten pool during laser processing of AlSi10Mg alloy. We then employ a multi-order parameter phase field model to study the microstructure evolution of LPBF-AlSi10Mg in the dilute limit, using the underlying thermal conditions for horizontal and vertical building directions as input. The phase field model employed here is designed to simulate solidification using heterogeneous nucleation from inoculant particles allowing to take into account morphological phenomena including the columnar-to-equiaxed transition (CET). The phase field model is first validated against the predictions of the previously developed steady-state CET theory of Hunt \cite{hunt1984steady}. It is then used under transient conditions to study microstructure evolution, revealing that the nucleation rate is noticeably higher in the horizontally built samples due to larger constitutional undercooling, which is consistent with experimental observations. We further quantify the effect of building direction on the local cooling conditions, and consequently on the grain morphology.
△ Less
Submitted 21 March, 2020;
originally announced March 2020.
-
High-Q Dual-Band Graphene Absorbers by Selective Excitation of Graphene Plasmon Polaritons: Circuit Model Analysis
Authors:
Saeedeh Barzegar-Parizi,
Amir Ebrahimi,
Kamran Ghorbani
Abstract:
This article presents the design of two dual-band graphene-based absorbers for terahertz frequencies. The absorbers are composed of two-dimensional (2D)arrays of ribbons and disks printed on a ground plane backed dielectric spacer. The design is based on the excitation of a specific plasmon polariton of the graphene patterned array at each resonance band. An analytical circuit model is used to der…
▽ More
This article presents the design of two dual-band graphene-based absorbers for terahertz frequencies. The absorbers are composed of two-dimensional (2D)arrays of ribbons and disks printed on a ground plane backed dielectric spacer. The design is based on the excitation of a specific plasmon polariton of the graphene patterned array at each resonance band. An analytical circuit model is used to derive closed-form relations for the geometrical parameters of the absorber and graphene parameters. The graphene patterned array appears as a surface admittance made of an infinite parallel array of series RLC branches. Each branch is equivalent to a graphene plasmon polariton (GPP) providing a distinct resonance mode. The design procedure is based on selectively exciting the first two GPPs. This means that two of the parallel RLC branches are selectively used in the circuit model analysis. The results obtained using the analytical solution are compared with the full-wave simulations in HFSS. The agreement between the results validates the developed design method.
△ Less
Submitted 7 December, 2019; v1 submitted 5 June, 2019;
originally announced June 2019.
-
Numerical study of liquid flow and heat transfer in rectangular microchannel with longitudinal vortex generators
Authors:
Amin Ebrahimi,
Ehsan Roohi,
Saeid Kheradmand
Abstract:
The liquid flow and conjugated heat transfer performance of single-phase laminar flow in rectangular microchannels equipped with longitudinal vortex generators (LVGs) are numerically investigated. Deionized-water with temperature-dependent thermo-physical properties is employed to conduct the simulations. Three-dimensional simulations are performed using an open-source flow solver based on finite…
▽ More
The liquid flow and conjugated heat transfer performance of single-phase laminar flow in rectangular microchannels equipped with longitudinal vortex generators (LVGs) are numerically investigated. Deionized-water with temperature-dependent thermo-physical properties is employed to conduct the simulations. Three-dimensional simulations are performed using an open-source flow solver based on finite volume approach and SIMPLEC algorithm. Five different configurations of the microchannel with different angles of attack of the LVGs are considered. Simulation results are compared with available experimental data and a deviation below 10% is achieved. The results show that there is a 2-25% increase in the Nusselt number for microchannels with LVGs, while the friction factor increased by 4-30%, for Reynolds number ranged from 100 to 1100. Except one at Re=100, the overall performance of the all configurations of microchannels with LVGs is higher than one.
△ Less
Submitted 7 November, 2018;
originally announced November 2018.
-
Numerical study of flow patterns and heat transfer in mini twisted oval tubes
Authors:
Amin Ebrahimi,
Ehsan Roohi
Abstract:
Flow patterns and heat transfer inside mini twisted oval tubes (TOTs) heated by constant-temperature walls are numerically investigated. Different configurations of tubes are simulated using water as the working fluid with temperature-dependent thermo-physical properties at Reynolds numbers ranging between 500 and 1100. After validating the numerical method with the published correlations and avai…
▽ More
Flow patterns and heat transfer inside mini twisted oval tubes (TOTs) heated by constant-temperature walls are numerically investigated. Different configurations of tubes are simulated using water as the working fluid with temperature-dependent thermo-physical properties at Reynolds numbers ranging between 500 and 1100. After validating the numerical method with the published correlations and available experimental results, the performance of TOTs is compared to a smooth circular tube. The overall performance of TOTs is evaluated by investigating the thermal-hydraulic performance and the results are analyzed in terms of the field synergy principle and entropy generation. Enhanced heat transfer performance for TOTs is observed at the expense of a higher pressure drop. Additionally, the secondary flow generated by the tube-wall twist is concluded to play a critical role in the augmentation of convective heat transfer, and consequently, better heat transfer performance. It is also observed that the improvement of synergy between velocity and temperature gradient and lower irreversibility cause heat transfer enhancement for TOTs.
△ Less
Submitted 6 November, 2018;
originally announced November 2018.
-
Hadronic Energy Resolution of a Combined High Granularity Scintillator Calorimeter System
Authors:
CALICE Collaboration,
J. Repond,
L. Xia,
J. Apostolakis,
G. Folger,
V. Ivantchenko,
A. Ribon,
V. Uzhinskiy,
D. Boumediene,
V. Francais,
G. C. Blazey,
A. Dyshkant,
K. Francis,
V. Zutshi,
O. Bach,
E. Brianne,
A. Ebrahimi,
K. Gadow,
P. Gttlicher,
O. Hartbrich F. Krivan,
K. Krüger,
J. Kvasnicka,
S. Lu,
C. Neubüser,
A. Provenza
, et al. (84 additional authors not shown)
Abstract:
This paper presents results obtained with the combined CALICE Scintillator Electromagnetic Calorimeter, Analogue Hadronic Calorimeter and Tail Catcher & Muon Tracker, three high granularity scintillator-SiPM calorimeter prototypes. The response of the system to pions with momenta between 4 GeV/c and 32 GeV/c is analysed, including the energy response, resolution, and longitudinal shower profiles.…
▽ More
This paper presents results obtained with the combined CALICE Scintillator Electromagnetic Calorimeter, Analogue Hadronic Calorimeter and Tail Catcher & Muon Tracker, three high granularity scintillator-SiPM calorimeter prototypes. The response of the system to pions with momenta between 4 GeV/c and 32 GeV/c is analysed, including the energy response, resolution, and longitudinal shower profiles. The results of a software compensation technique based on weighting according to hit energy are compared to those of a standard linear energy reconstruction. The results are compared to predictions of the GEANT4 physics lists QGSP_BERT_HP and FTFP_BERT_HP.
△ Less
Submitted 12 September, 2018; v1 submitted 11 September, 2018;
originally announced September 2018.
-
Laminar convective heat transfer of shear-thinning liquids in rectangular channels with longitudinal vortex generators
Authors:
Amin Ebrahimi,
Benyamin Naranjani,
Shayan Milani,
Farzad Dadras Javan
Abstract:
Heat and fluid flow in a rectangular channel heat sink equipped with longitudinal vortex generators have been numerically investigated in the range of Reynolds numbers between 25 and 200. Aqueous solutions of carboxymethyl cellulose (CMC) with different concentrations (200-2000 ppm), which are shear-thinning non-Newtonian liquids, have been utilised as working fluid. Three-dimensional simulations…
▽ More
Heat and fluid flow in a rectangular channel heat sink equipped with longitudinal vortex generators have been numerically investigated in the range of Reynolds numbers between 25 and 200. Aqueous solutions of carboxymethyl cellulose (CMC) with different concentrations (200-2000 ppm), which are shear-thinning non-Newtonian liquids, have been utilised as working fluid. Three-dimensional simulations have been performed on a plain channel and a channel with five pairs of vortex generators. The channels have a hydraulic diameter of 8 mm and are heated by constant wall temperature. The vortex generators have been mounted at different angles of attack and locations inside the channel. The shear-thinning liquid flow in rectangular channels with longitudinal vortex generators are described and the mechanisms of heat transfer enhancement are discussed. The results demonstrate a heat transfer enhancement of 39-188% using CMC aqueous solutions in rectangular channels with LVGs with respect to a Newtonian liquid flow (i.e. water). Additionally, it is shown that equip** rectangular channels with LVGs results in an enhancement of 24-135% in heat transfer performance vis-à-vis plain channel. However, this heat transfer enhancement is associated with larger pressure losses. For the range of parameters studied in this paper, increasing the CMC concentration, the angle of attack of vortex generators and their lateral distances leads to an increase in heat transfer performance. Additionally, heat transfer performance of rectangular channels with longitudinal vortex generators enhances with increasing the Reynolds number in the laminar flow regime.
△ Less
Submitted 10 July, 2018;
originally announced July 2018.
-
An investigation on thermo-hydraulic performance of a flat-plate channel with pyramidal protrusions
Authors:
Amin Ebrahimi,
Benyamin Naranjani
Abstract:
In this study, a flat-plate channel configured with pyramidal protrusions are numerically analysed for the first time. Simulations of laminar single-phase fluid flow and heat transfer characteristics are developed using a finite-volume approach under steady-state condition. Pure water is selected as the coolant and its thermo-physical properties are modelled using a set of temperature-dependent fu…
▽ More
In this study, a flat-plate channel configured with pyramidal protrusions are numerically analysed for the first time. Simulations of laminar single-phase fluid flow and heat transfer characteristics are developed using a finite-volume approach under steady-state condition. Pure water is selected as the coolant and its thermo-physical properties are modelled using a set of temperature-dependent functions. Different configurations of the channel, including a plain channel and a channel with nature-inspired protruded surfaces, are studied here for Reynolds numbers ranging from 135 to 1430. The effects of the protrusion shape, size and arrangement on the hydrothermal performance of a flat-plate channel are studied in details. The temperature of the upper and lower surfaces of the channel is kept constant during the simulations. It is observed that utilizing these configurations can boost the heat transfer up to 277.9% and amplify the pressure loss up to 179.4% with a respect to the plain channel. It is found that the overall efficiency of the channels with pyramidal protrusions is improved by 12.0-169.4% compared to the plain channel for the conditions studied here. Furthermore, the thermodynamic performance of the channel is investigated in terms of entropy generation and it is found that equip** the channels with pyramidal protrusions leads to lower irreversibility in the system.
△ Less
Submitted 10 July, 2018;
originally announced July 2018.
-
First study of small-cell 3D Silicon Pixel Detectors for the High Luminosity LHC
Authors:
E. Currás,
J. Duarte-Campderrós,
M. Fernández,
A. García,
G. Gómez,
J. González,
R. Jaramillo,
D. Moya,
I. Vila,
S. Hidalgo,
M. Manna,
G. Pellegrini,
D. Quirion,
D. Pitzl,
A. Ebrahimi,
T. Rohe,
S. Wiederkehr
Abstract:
A study of 3D pixel sensors of cell size 50 μm x 50 μm fabricated at IMB-CNM using double-sided n-on-p 3D technology is presented. Sensors were bump-bonded to the ROC4SENS readout chip. For the first time in such a small-pitch hybrid assembly, the sensor response to ionizing radiation in a test beam of 5.6 GeV electrons was studied. Results for non-irradiated sensors are presented, including effic…
▽ More
A study of 3D pixel sensors of cell size 50 μm x 50 μm fabricated at IMB-CNM using double-sided n-on-p 3D technology is presented. Sensors were bump-bonded to the ROC4SENS readout chip. For the first time in such a small-pitch hybrid assembly, the sensor response to ionizing radiation in a test beam of 5.6 GeV electrons was studied. Results for non-irradiated sensors are presented, including efficiency, charge sharing, signal-to-noise, and resolution for different incidence angles.
△ Less
Submitted 4 June, 2018;
originally announced June 2018.
-
Flow and Thermal Fields Investigation in Divergent Micro/Nano Channels
Authors:
Amin Ebrahimi,
Ehsan Roohi
Abstract:
The present work is related to the study of the nitrogen gas flow through diverging micro and nano-channels. The direct simulation Monte-Carlo (DSMC) method has been used to study the flow. The Simplified Bernoulli Trials (SBT) collision scheme has been employed to reduce the computational costs and required amounts of the computer resources. The effects of various divergence angles on flow and th…
▽ More
The present work is related to the study of the nitrogen gas flow through diverging micro and nano-channels. The direct simulation Monte-Carlo (DSMC) method has been used to study the flow. The Simplified Bernoulli Trials (SBT) collision scheme has been employed to reduce the computational costs and required amounts of the computer resources. The effects of various divergence angles on flow and thermal fields have been studied for different Knudsen numbers in late-slip and early-transition regimes. The inlet-to-outlet pressure ratio has been set to 2.5 for micro and nano-channels with a uniform constant wall temperature. By analyzing the numerical results no flow separation has been found due to slip at the wall which is different than flow behavior in continuum regime. The results indicate that the viscous component has a relatively large contribution to the overall pressure drop and flow behavior. It observed that for low divergence angles the effects of pressure forces dominate the effects of shear stress and divergence angle and cause the flow to accelerate along the channel while by increasing the divergence angle and therefore the effects of flow expansion, the flow decelerates along the channel. The mass flow rate through channel increases by increasing the divergence angle. Cold-to-hot heat transfer has been observed in diverging micro and nano-channels. In order to investigate the thermal behavior in diverging micro and nano-channels, the results have been compared to weakly non-linear constitutive laws derived from Boltzmann's equation.
△ Less
Submitted 25 January, 2018;
originally announced January 2018.
-
DSMC investigation of rarefied gas flow through diverging micro- and nanochannels
Authors:
Amin Ebrahimi,
Ehsan Roohi
Abstract:
Direct simulation Monte Carlo (DSMC) method with simplified Bernoulli-trials (SBT) collision scheme has been used to study the rarefied pressure-driven nitrogen flow through diverging microchannels. The fluid behaviours flowing between two plates with different divergence angles ranging between 0$^{\circ}$ to 17$^{\circ}$ are described at different pressure ratios (1.5${\le}{\prod}{\le}$2.5) and K…
▽ More
Direct simulation Monte Carlo (DSMC) method with simplified Bernoulli-trials (SBT) collision scheme has been used to study the rarefied pressure-driven nitrogen flow through diverging microchannels. The fluid behaviours flowing between two plates with different divergence angles ranging between 0$^{\circ}$ to 17$^{\circ}$ are described at different pressure ratios (1.5${\le}{\prod}{\le}$2.5) and Knudsen numbers (0.03${\le}$Kn${\le}$12.7). The primary flow field properties, including pressure, velocity, and temperature, are presented for divergent microchannels and are compared with those of a microchannel with a uniform cross-section. The variations of the flow field properties in divergent microchannels, which are influenced by the area change, the channel pressure ratio and the rarefication are discussed. The results show no flow separation in divergent microchannels for all the range of simulation parameters studied in the present work. It has been found that a divergent channel can carry higher amounts of mass in comparison with an equivalent straight channel geometry. A correlation between the mass flow rate through microchannels, the divergence angle, the pressure ratio, and the Knudsen number has been suggested. The present numerical findings prove the occurrence of Knudsen minimum phenomenon in micro- and Nano- channels with non-uniform cross-sections.
△ Less
Submitted 2 February, 2017; v1 submitted 5 January, 2017;
originally announced January 2017.
-
Commissioning of the new multi-layer integration prototype of the CALICE tile hadron calorimeter
Authors:
Aliakbar Ebrahimi
Abstract:
The basic prototype of a tile hadron calorimeter (HCAL) for the International Linear Collider (ILC) has been realised and extensively tested. A major aspect of the proposed concept is the improvement of the jet energy resolution by measuring details of the shower development and combining them with the data of the tracking system (particle flow). The prototype utilises scintillating tiles that are…
▽ More
The basic prototype of a tile hadron calorimeter (HCAL) for the International Linear Collider (ILC) has been realised and extensively tested. A major aspect of the proposed concept is the improvement of the jet energy resolution by measuring details of the shower development and combining them with the data of the tracking system (particle flow). The prototype utilises scintillating tiles that are read out by novel Silicon Photomultipliers (SiPMs) and takes into account all design aspects that are demanded by the intended operation at the ILC. Currently, a new 12 layer prototype with about 3400 detector channels is under development. Alternative architectures for the scintillating tiles with and without wavelength-shifting fibres and tiles with individual wrap** with reflector foil is tested as well as different types of SiPMs. The new prototype was used for the first time at the CERN Proton Synchrotron test facility in fall 2014. Additionally, detector modules for the CALICE scintillator-based Electromagnetic Calorimeter (Sc-ECAL), that follow the proposed HCAL electronics architecture, were part of this new prototype. A new multi-layer Data Acquisition System (DAQ) was used for the detector configuration and operation.
△ Less
Submitted 6 October, 2016;
originally announced October 2016.
-
Resistive Plate Chamber Digitization in a Hadronic Shower Environment
Authors:
Z. Deng,
Y. Li,
Y. Wang,
Q. Yue,
Z. Yang,
J. Apostolakis,
G. Folger,
C. Grefe,
V. Ivantchenko,
A. Ribon,
V. Uzhinskiy,
D. Boumediene,
C. Carloganu,
V. Français,
G. Cho,
D-W. Kim,
S. C. Lee,
W. Park,
S. Vallecorsa,
S. Cauwenbergh,
M. Tytgat,
A. **ault,
N. Zaganidis,
E. Brianne,
A. Ebrahimi
, et al. (103 additional authors not shown)
Abstract:
The CALICE Semi-Digital Hadron Calorimeter (SDHCAL) technological prototype is a sampling calorimeter using Glass Resistive Plate Chamber detectors with a three-threshold readout as the active medium. This technology is one of the two options proposed for the hadron calorimeter of the International Large Detector for the International Linear Collider. The prototype was exposed to beams of muons, e…
▽ More
The CALICE Semi-Digital Hadron Calorimeter (SDHCAL) technological prototype is a sampling calorimeter using Glass Resistive Plate Chamber detectors with a three-threshold readout as the active medium. This technology is one of the two options proposed for the hadron calorimeter of the International Large Detector for the International Linear Collider. The prototype was exposed to beams of muons, electrons and pions of different energies at the CERN Super Proton Synchrotron. To be able to study the performance of such a calorimeter in future experiments it is important to ensure reliable simulation of its response. In this paper we present our prototype simulation performed with GEANT4 and the digitization procedure achieved with an algorithm called SimDigital. A detailed description of this algorithm is given and the methods to determinate its parameters using muon tracks and electromagnetic showers are explained. The comparison with hadronic shower data shows a good agreement up to 50 GeV. Discrepancies are observed at higher energies. The reasons for these differences are investigated.
△ Less
Submitted 15 April, 2016;
originally announced April 2016.
-
DHCAL with Minimal Absorber: Measurements with Positrons
Authors:
The CALICE Collaboration,
B. Freund,
C. Neubüser,
J. Repond,
J. Schlereth,
L. Xia,
A. Dotti,
C. Grefe,
V. Ivantchenko,
J. Berenguer Antequera,
E. Calvo Alamillo,
M. -C. Fouz,
J. Marin,
J. Puerta-Pelayo,
A. Verdugo,
E. Brianne,
A. Ebrahimi,
K. Gadow,
P. Göttlicher,
C. Günter,
O. Hartbrich,
B. Hermberg,
A. Irles,
F. Krivan,
K. Krüger
, et al. (78 additional authors not shown)
Abstract:
In special tests, the active layers of the CALICE Digital Hadron Calorimeter prototype, the DHCAL, were exposed to low energy particle beams, without being interleaved by absorber plates. The thickness of each layer corresponded approximately to 0.29 radiation lengths or 0.034 nuclear interaction lengths, defined mostly by the copper and steel skins of the detector cassettes. This paper reports on…
▽ More
In special tests, the active layers of the CALICE Digital Hadron Calorimeter prototype, the DHCAL, were exposed to low energy particle beams, without being interleaved by absorber plates. The thickness of each layer corresponded approximately to 0.29 radiation lengths or 0.034 nuclear interaction lengths, defined mostly by the copper and steel skins of the detector cassettes. This paper reports on measurements performed with this device in the Fermilab test beam with positrons in the energy range of 1 to 10 GeV. The measurements are compared to simulations based on GEANT4 and a standalone program to emulate the detailed response of the active elements.
△ Less
Submitted 4 March, 2016;
originally announced March 2016.
-
Hadron shower decomposition in the highly granular CALICE analogue hadron calorimeter
Authors:
The CALICE Collaboration,
G. Eigen,
T. Price,
N. K. Watson,
J. S. Marshall,
M. A. Thomson,
D. R. Ward,
D. Benchekroun,
A. Hoummada,
Y. Khoulaki,
J. Apostolakis,
A. Dotti,
G. Folger,
V. Ivantchenko,
A. Ribon,
V. Uzhinskiy,
J. -Y. Hostachy,
L. Morin,
E. Brianne,
A. Ebrahimi,
K. Gadow,
P. Göttlicher,
C. Günter,
O. Hartbrich,
B. Hermberg
, et al. (135 additional authors not shown)
Abstract:
The spatial development of hadronic showers in the CALICE scintillator-steel analogue hadron calorimeter is studied using test beam data collected at CERN and FNAL for single positive pions and protons with initial momenta in the range from 10 to 80 GeV/c. Both longitudinal and radial development of hadron showers are parametrised with two-component functions. The parametrisation is fit to test be…
▽ More
The spatial development of hadronic showers in the CALICE scintillator-steel analogue hadron calorimeter is studied using test beam data collected at CERN and FNAL for single positive pions and protons with initial momenta in the range from 10 to 80 GeV/c. Both longitudinal and radial development of hadron showers are parametrised with two-component functions. The parametrisation is fit to test beam data and simulations using the QGSP_BERT and FTFP_BERT physics lists from Geant4 version 9.6. The parameters extracted from data and simulated samples are compared for the two types of hadrons. The response to pions and the ratio of the non-electromagnetic to the electromagnetic calorimeter response, h/e, are estimated using the extrapolation and decomposition of the longitudinal profiles.
△ Less
Submitted 15 March, 2016; v1 submitted 27 February, 2016;
originally announced February 2016.
-
First results of the CALICE SDHCAL technological prototype
Authors:
V. Buridon,
C. Combaret,
L. Caponetto,
R. Eté,
G. Garillot,
G. Grenier,
R. Han,
J. C. Ianigro,
R. Kieffer,
I. Laktineh,
N. Lumb,
H. Mathez,
L. Mirabito,
A. Petrukhin,
A. Steen,
J. Berenguer Antequera,
E. Calvo Alamillo,
M. -C. Fouz,
J. Marin,
J. Puerta-Pelayo,
A. Verdugo,
E. Cortina Gil,
S. Mannai,
S. Cauwenbergh,
M. Tytgat
, et al. (96 additional authors not shown)
Abstract:
The CALICE Semi-Digital Hadronic Calorimeter (SDHCAL) prototype, built in 2011, was exposed to beams of hadrons, electrons and muons in two short periods in 2012 on two different beam lines of the CERN SPS. The prototype with its 48 active layers, made of Glass Resistive Plate Chambers and their embedded readout electronics, was run in triggerless and power-pulsing mode. The performance of the SDH…
▽ More
The CALICE Semi-Digital Hadronic Calorimeter (SDHCAL) prototype, built in 2011, was exposed to beams of hadrons, electrons and muons in two short periods in 2012 on two different beam lines of the CERN SPS. The prototype with its 48 active layers, made of Glass Resistive Plate Chambers and their embedded readout electronics, was run in triggerless and power-pulsing mode. The performance of the SDHCAL during the test beam was found to be very satisfactory with an efficiency exceeding 90% for almost all of the 48 active layers. A linear response (within 5%) and a good energy resolution are obtained for a large range of hadronic energies (5-80GeV) by applying appropriate calibration coefficients to the collected data for both the Digital (Binary) and the Semi-Digital (Multi-threshold) modes of the SDHCAL prototype. The Semi-Digital mode shows better performance at energies exceeding 30GeV
△ Less
Submitted 20 March, 2016; v1 submitted 6 February, 2016;
originally announced February 2016.
-
Pion and proton showers in the CALICE scintillator-steel analogue hadron calorimeter
Authors:
The CALICE Collaboration,
B. Bilki,
J. Repond,
L. Xia,
G. Eigen,
M. A. Thomson,
D. R. Ward,
D. Benchekroun,
A. Hoummada,
Y. Khoulaki,
S. Chang,
A. Khan,
D. H. Kim,
D. J. Kong,
Y. D. Oh,
G. C. Blazey,
A. Dyshkant,
K. Francis,
J. G. R. Lima,
R. Salcido,
V. Zutshi,
F. Salvatore,
K. Kawagoe,
Y. Miyazaki,
Y. Sudo
, et al. (147 additional authors not shown)
Abstract:
Showers produced by positive hadrons in the highly granular CALICE scintillator-steel analogue hadron calorimeter were studied. The experimental data were collected at CERN and FNAL for single particles with initial momenta from 10 to 80 GeV/c. The calorimeter response and resolution and spatial characteristics of shower development for proton- and pion-induced showers for test beam data and simul…
▽ More
Showers produced by positive hadrons in the highly granular CALICE scintillator-steel analogue hadron calorimeter were studied. The experimental data were collected at CERN and FNAL for single particles with initial momenta from 10 to 80 GeV/c. The calorimeter response and resolution and spatial characteristics of shower development for proton- and pion-induced showers for test beam data and simulations using Geant4 version 9.6 are compared.
△ Less
Submitted 15 March, 2015; v1 submitted 8 December, 2014;
originally announced December 2014.
-
Multi-scale approach to invasion percolation of rock fracture networks
Authors:
Ali N. Ebrahimi,
Falk K. Wittel,
Nuno A. M. Araújo,
Hans J. Herrmann
Abstract:
A multi-scale scheme for the invasion percolation of rock fracture networks with heterogeneous fracture aperture fields is proposed. Inside fractures, fluid transport is calculated on the finest scale and found to be localized in channels as a consequence of the aperture field. The channel network is characterized and reduced to a vectorized artificial channel network (ACN). Different realizations…
▽ More
A multi-scale scheme for the invasion percolation of rock fracture networks with heterogeneous fracture aperture fields is proposed. Inside fractures, fluid transport is calculated on the finest scale and found to be localized in channels as a consequence of the aperture field. The channel network is characterized and reduced to a vectorized artificial channel network (ACN). Different realizations of ACNs are used to systematically calculate efficient apertures for fluid transport inside differently sized fractures as well as fracture intersection and entry properties. Typical situations in fracture networks are parameterized by fracture inclination, flow path length along the fracture and intersection lengths in the entrance and outlet zones of fractures. Using these scaling relations obtained from the finer scales, we simulate the invasion process of immiscible fluids into saturated discrete fracture networks, which were studied in previous works.
△ Less
Submitted 11 August, 2014;
originally announced August 2014.
-
The Time Structure of Hadronic Showers in highly granular Calorimeters with Tungsten and Steel Absorbers
Authors:
C. Adloff,
J. -J. Blaising,
M. Chefdeville,
C. Drancourt,
R. Gaglione,
N. Geffroy,
Y. Karyotakis,
I. Koletsou,
J. Prast,
G. Vouters J. Repond,
J. Schlereth,
L. Xia E. Baldolemar,
J. Li,
S. T. Park,
M. Sosebee,
A. P. White,
J. Yu,
G. Eigen,
M. A. Thomson,
D. R. Ward,
D. Benchekroun,
A. Hoummada,
Y. Khoulaki J. Apostolakis,
S. Arfaoui,
M. Benoit
, et al. (188 additional authors not shown)
Abstract:
The intrinsic time structure of hadronic showers influences the timing capability and the required integration time of hadronic calorimeters in particle physics experiments, and depends on the active medium and on the absorber of the calorimeter. With the CALICE T3B experiment, a setup of 15 small plastic scintillator tiles read out with Silicon Photomultipliers, the time structure of showers is m…
▽ More
The intrinsic time structure of hadronic showers influences the timing capability and the required integration time of hadronic calorimeters in particle physics experiments, and depends on the active medium and on the absorber of the calorimeter. With the CALICE T3B experiment, a setup of 15 small plastic scintillator tiles read out with Silicon Photomultipliers, the time structure of showers is measured on a statistical basis with high spatial and temporal resolution in sampling calorimeters with tungsten and steel absorbers. The results are compared to GEANT4 (version 9.4 patch 03) simulations with different hadronic physics models. These comparisons demonstrate the importance of using high precision treatment of low-energy neutrons for tungsten absorbers, while an overall good agreement between data and simulations for all considered models is observed for steel.
△ Less
Submitted 21 July, 2014; v1 submitted 25 April, 2014;
originally announced April 2014.
-
Performance of the first prototype of the CALICE scintillator strip electromagnetic calorimeter
Authors:
CALICE Collaboration,
K. Francis,
J. Repond,
J. Schlereth,
J. Smith,
L. Xia,
E. Baldolemar,
J. Li,
S. T. Park,
M. Sosebee,
A. P. White,
J. Yu,
G. Eigen,
Y. Mikami,
N. K. Watson,
M. A. Thomson,
D. R. Ward,
D. Benchekroun,
A. Hoummada,
Y. Khoulaki,
J. Apostolakis,
A. Dotti,
G. Folger,
V. Ivantchenko,
A. Ribon
, et al. (169 additional authors not shown)
Abstract:
A first prototype of a scintillator strip-based electromagnetic calorimeter was built, consisting of 26 layers of tungsten absorber plates interleaved with planes of 45x10x3 mm3 plastic scintillator strips. Data were collected using a positron test beam at DESY with momenta between 1 and 6 GeV/c. The prototype's performance is presented in terms of the linearity and resolution of the energy measur…
▽ More
A first prototype of a scintillator strip-based electromagnetic calorimeter was built, consisting of 26 layers of tungsten absorber plates interleaved with planes of 45x10x3 mm3 plastic scintillator strips. Data were collected using a positron test beam at DESY with momenta between 1 and 6 GeV/c. The prototype's performance is presented in terms of the linearity and resolution of the energy measurement. These results represent an important milestone in the development of highly granular calorimeters using scintillator strip technology. This technology is being developed for a future linear collider experiment, aiming at the precise measurement of jet energies using particle flow techniques.
△ Less
Submitted 11 June, 2014; v1 submitted 15 November, 2013;
originally announced November 2013.
-
Shower development of particles with momenta from 1 to 10 GeV in the CALICE Scintillator-Tungsten HCAL
Authors:
C. Adloff,
J. -J. Blaising,
M. Chefdeville,
C. Drancourt,
R. Gaglione,
N. Geffroy,
Y. Karyotakis,
I. Koletsou,
J. Prast,
G. Vouters,
J. Repond,
J. Schlereth,
J. Smith,
L. Xia,
E. Baldolemar,
J. Li,
S. T. Park,
M. Sosebee,
A. P. White,
J. Yu,
G. Eigen,
M. A. Thomson,
D. R. Ward,
D. Benchekroun,
A. Hoummada
, et al. (194 additional authors not shown)
Abstract:
Lepton colliders are considered as options to complement and to extend the physics programme at the Large Hadron Collider. The Compact Linear Collider (CLIC) is an $e^+e^-$ collider under development aiming at centre-of-mass energies of up to 3 TeV. For experiments at CLIC, a hadron sampling calorimeter with tungsten absorber is proposed. Such a calorimeter provides sufficient depth to contain hig…
▽ More
Lepton colliders are considered as options to complement and to extend the physics programme at the Large Hadron Collider. The Compact Linear Collider (CLIC) is an $e^+e^-$ collider under development aiming at centre-of-mass energies of up to 3 TeV. For experiments at CLIC, a hadron sampling calorimeter with tungsten absorber is proposed. Such a calorimeter provides sufficient depth to contain high-energy showers, while allowing a compact size for the surrounding solenoid.
A fine-grained calorimeter prototype with tungsten absorber plates and scintillator tiles read out by silicon photomultipliers was built and exposed to particle beams at CERN. Results obtained with electrons, pions and protons of momenta up to 10 GeV are presented in terms of energy resolution and shower shape studies. The results are compared with several GEANT4 simulation models in order to assess the reliability of the Monte Carlo predictions relevant for a future experiment at CLIC.
△ Less
Submitted 13 January, 2014; v1 submitted 14 November, 2013;
originally announced November 2013.
