-
Graphene-Based Transparent Flexible Strain Gauges with Tunable Sensitivity and Strain Range
Authors:
Joseph Neilson,
Pietro Cataldi,
Brian Derby
Abstract:
Flexible strain gauges with 88% optical transmittance, of reduced graphene oxide (rGO) on poly dimethylsiloxne membranes, are produced form monolayers of graphene oxide assembled into densely packed sheets at an immiscible hexane/water interface and subsequently reduced in HI vapor to increase electrical conductivity. Pre-straining and relaxing the membranes introduces a population of cracks into…
▽ More
Flexible strain gauges with 88% optical transmittance, of reduced graphene oxide (rGO) on poly dimethylsiloxne membranes, are produced form monolayers of graphene oxide assembled into densely packed sheets at an immiscible hexane/water interface and subsequently reduced in HI vapor to increase electrical conductivity. Pre-straining and relaxing the membranes introduces a population of cracks into the rGO film. Subsequent straining opens these cracks, inducing piezoresistivity. Reduction for 30 s forms an array of parallel cracks that do not individually span the membrane and results in a strain gauge with a usable strain range > 0.2 and gauge factor of 20 - 100 at low strain levels that increases with increasing pre-strain. In all cases the gauge facto decreases with increasing applied strain and asymptotes to a value of about 3, as it approaches the pre-strain value. If the rGO is reduced for 60 s, the cracks fully span the width of the membrane, leading to an increased gauge resistance but a much more sensitive strain gauge with GF ranging from 1000 - 16000. However, the usable strain range reduces to < 0.01. A simple equivalent resistor model is proposed to describe the behaviour of both gauge types. The gauges show a repeatable and stable response with loading frequencies up to 1 kHz and have been used to detect human body motion in a simple e-skin demonstration.
△ Less
Submitted 9 June, 2023; v1 submitted 27 April, 2023;
originally announced April 2023.
-
Electrically Conductive 2D Material Coatings for Flexible & Stretchable Electronics: A Comparative Review of Graphenes & MXenes
Authors:
Vicente Orts Mercadillo,
Kai Chio Chan,
Mario Caironi,
Athanassia Athanassiou,
Ian A. Kinloch,
Mark Bissett,
Pietro Cataldi
Abstract:
There is growing interest in transitioning electronic components and circuitry from stiff and rigid substrates to more flexible and stretchable platforms, such as thin plastics, textiles, and foams. In parallel, the push for more sustainable, biocompatible, and cost-efficient conductive inks to coat these substrates, has led to the development of formulations with novel nanomaterials. Among these,…
▽ More
There is growing interest in transitioning electronic components and circuitry from stiff and rigid substrates to more flexible and stretchable platforms, such as thin plastics, textiles, and foams. In parallel, the push for more sustainable, biocompatible, and cost-efficient conductive inks to coat these substrates, has led to the development of formulations with novel nanomaterials. Among these, 2D materials, and particularly graphenes and MXenes, have received intense research interest due to their increasingly facile and scalable production, high electrical conductivity, and compatibility with existing manufacturing techniques. They enable a range of electronic devices, including strain and pressure sensors, supercapacitors, thermoelectric generators, and heaters. These new flexible and stretchable electronic devices developed with 2D material coatings are poised to unlock exciting applications in the wearable, healthcare and Internet of Things sectors. This review has surveyed key data from more than 200 articles published over the last 6 years, to provide a quantitative analysis of recent progress in the field and shade light on future directions and prospects of this technology. We find that despite the different chemical origins of graphenes and MXenes, their shared electrical properties and 2D morphology, guarantee intriguing performance in end applications, leaving plenty of space for shared progress and advancements in the future.
△ Less
Submitted 14 July, 2022;
originally announced July 2022.
-
An Electrically Conductive Oleogel Paste for Edible Electronics
Authors:
Pietro Cataldi,
Leonardo Lamanna,
Claudia Bertei,
Federica Arena,
Pietro Rossi,
Mufeng Liu,
Fabio Di Fonzo,
Dimitrios G. Papageorgiou,
Alessandro Luzio,
Mario Caironi
Abstract:
Edible electronics will facilitate point-of-care testing through safe and cheap devices that are digested or degraded in the body or environment after performing a specific function. Its thrive depends on creating a library of materials that are the basic building blocks for eatable technologies. Edible electrical conductors fabricated with green methods that allow production at a large scale and…
▽ More
Edible electronics will facilitate point-of-care testing through safe and cheap devices that are digested or degraded in the body or environment after performing a specific function. Its thrive depends on creating a library of materials that are the basic building blocks for eatable technologies. Edible electrical conductors fabricated with green methods that allow production at a large scale and composed of food derivatives, ingestible in large amounts without risk for human health are needed. Here, conductive pastes made with materials with a high tolerable upper intake limit (major of mg/kg body weight /day) are proposed. Conductive oleogel paste composites, made with biodegradable and food-grade materials like natural waxes, oils, and activated carbon conductive fillers, are presented. The proposed pastes are compatible with manufacturing processes such as direct ink writing and thus are suitable for an industrial scale-up. These conductors are built without the use of solvents, and with tunable electromechanical features and adhesion depending on the composition. They have antibacterial and hydrophobic properties, so that they can be used in contact with food preventing contamination and preserving its organoleptic properties. As a proof-of-principle application, the edible conductive pastes are demonstrated to be effective edible contacts for food impedance analysis, to be integrated for example in smart fruit labels for ripening monitoring.
△ Less
Submitted 2 May, 2022;
originally announced May 2022.
-
Electrically controlled heat transport in multilayer graphene
Authors:
Pietro Steiner,
Saqeeb Adnan,
Muhammed Said Ergoktas,
Julien Barrier,
Xiaoxiao Yu,
Vicente Orts,
Gokhan Bakan,
Jonathan Aze,
Yury Malevich,
Kaiyuan Wang,
Pietro Cataldi,
Mark Bisset,
Sinan Balci,
Sefik Suzer,
Marat Khafizov,
Coskun Kocabas
Abstract:
The ability to control heat transport with electrical signals has been an outstanding challenge due to the lack of efficient electrothermal materials. Previous attempts have mainly concentrated on phase-change and layered materials and encountered various problems such as low thermal conductivities and modest on/off ratios. Here, we demonstrate a graphene-based electrothermal switch enabling elect…
▽ More
The ability to control heat transport with electrical signals has been an outstanding challenge due to the lack of efficient electrothermal materials. Previous attempts have mainly concentrated on phase-change and layered materials and encountered various problems such as low thermal conductivities and modest on/off ratios. Here, we demonstrate a graphene-based electrothermal switch enabling electrically tuneable heat flow. The device uses reversible electro-intercalation of ions to modulate the in-plane thermal conductivity of graphene film by over thirteen-fold via electrically tuneable phonon scattering. We anticipate that our results could provide a realistic pathway for adaptive thermal transport enabling a new class of electrically driven thermal devices which would find a broad spectrum of applications in aerospace and microelectronics.
△ Less
Submitted 21 February, 2022;
originally announced February 2022.
-
Multifunctional Biocomposites based on Polyhydroxyalkanoate and Graphene/Carbon-Nanofiber Hybrids for Electrical and Thermal Applications
Authors:
Pietro Cataldi,
Pietro Steiner,
Thomas Raine,
Kailing Lin,
Coskun Kocabas,
Robert J. Young,
Mark Bissett,
Ian A. Kinloch,
Dimitrios G. Papageorgiou
Abstract:
Most polymers are long-lasting and produced from monomers derived from fossil fuel sources. Bio-based and/or biodegradable plastics have been proposed as a sustainable alternative. Amongst those available, polyhydroxyalkanoate (PHA) shows great potential across a large variety of applications but is currently limited to packaging, cosmetics and tissue engineering due to its relatively poor physica…
▽ More
Most polymers are long-lasting and produced from monomers derived from fossil fuel sources. Bio-based and/or biodegradable plastics have been proposed as a sustainable alternative. Amongst those available, polyhydroxyalkanoate (PHA) shows great potential across a large variety of applications but is currently limited to packaging, cosmetics and tissue engineering due to its relatively poor physical properties. An expansion of its uses can be accomplished by develo** nanocomposites where PHAs are used as the polymer matrix. Herein, a PHA biopolyester was melt blended with graphene nanoplatelets (GNPs) or with a 1:1 hybrid mixture of GNPs and carbon nanofibers (CNFs). The resulting nanocomposites exhibited enhanced thermal stability while their Young's modulus roughly doubled compared to pure PHA. The hybrid nanocomposites percolated electrically at lower nanofiller loadings compared to the GNP-PHA system. The electrical conductivity at 15 wt.% loading was ~ 6 times higher than the GNP-based sample. As a result, the electromagnetic interference shielding performance of the hybrid material was around 50% better than the pure GNPs nanocomposites, exhibiting shielding effectiveness above 20 dB, which is the threshold for common commercial applications. The thermal conductivity increased significantly for both types of bio-nanocomposites and reached values around 5 W K-1 m-1 with the hybrid-based material displaying the best performance. Considering the solvent-free and industrially compatible production method, the proposed multifunctional materials are promising to expand the range of application of PHAs and increase the environmental sustainability of the plastic and plastic electronics industry.
△ Less
Submitted 18 May, 2020;
originally announced May 2020.
-
Graphene-Polyurethane Coatings for Deformable Conductors and Electromagnetic Interference Shielding
Authors:
Pietro Cataldi,
Dimitrios G. Papageorgiou,
Gergo Pinter,
Andrey V. Kretinin,
William W. Sampson,
Robert J. Young,
Mark Bissett,
Ian A. Kinloch
Abstract:
Electrically conductive, polymeric materials that maintain their conductivity even when under significant mechanical deformation are needed for actuator electrodes, conformable electromagnetic shielding, stretchable tactile sensors and flexible energy storage. The challenge for these materials is that the percolated, electrically conductive networks tend to separate even at low strains, leading to…
▽ More
Electrically conductive, polymeric materials that maintain their conductivity even when under significant mechanical deformation are needed for actuator electrodes, conformable electromagnetic shielding, stretchable tactile sensors and flexible energy storage. The challenge for these materials is that the percolated, electrically conductive networks tend to separate even at low strains, leading to significant piezoresistance. Herein, deformable conductors were fabricated by spray-coating a nitrile substrate with a graphene-elastomer solution. The coatings showed only slight increase in electrical resistance after thousands of bending cycles and repeated folding-unfolding events. The deformable conductors doubled their electrical resistance at 12% strain and were washable without changing their electrical properties. The conductivity-strain behaviour was modelled by considering the nanofiller separation upon deformation. To boost the conductivity at higher strains, the production process was adapted by stretching the nitrile substrate before spraying, after which it was released. This adaption meant that the electrical resistance doubled at 25 % strain. The electrical resistance was found sufficiently low to give a 1.9 dB/μm shielding in the 8-12 GHz electromagnetic band. The physical and electrical properties, including the EM screening, of the flexible conductors, were found to deteriorate upon cycling but could be recovered through reheating the coating.
△ Less
Submitted 24 April, 2020;
originally announced April 2020.
-
Hybrid Graphene/Carbon Nanofiber Wax Emulsion for Paper-based Electronics and Thermal Management
Authors:
Xinhui Wu,
Pietro Steiner,
Thomas Raine,
Gergo Pinter,
Andrey Kretinin,
Coskun Kocabas,
Mark Bissett,
Pietro Cataldi
Abstract:
Materials for electronics that function as electrical and/or thermal conductors are often rigid, expensive, difficult to be sourced and sometimes toxic. An electrically and thermally conductive nanocomposite that is lightweight, flexible and eco-friendly could improve the environmental friendliness of the electronics sector and enable new applications. Considering this, we have fabricated electric…
▽ More
Materials for electronics that function as electrical and/or thermal conductors are often rigid, expensive, difficult to be sourced and sometimes toxic. An electrically and thermally conductive nanocomposite that is lightweight, flexible and eco-friendly could improve the environmental friendliness of the electronics sector and enable new applications. Considering this, we have fabricated electrically and thermally conductive flexible materials by functionalizing paper with nanocarbon conductive inks. Carnauba wax is emulsified in isopropyl alcohol and mixed with graphene nanoplatelets (GNPs) or with hybrids of GNPs and carbon nanofibers (CNFs). The percolation threshold of the hybrid samples is lowered compared with the pure GNPs composites, due to their increased filler aspect ratio. The hybrid samples also exhibit superior bending and folding stability. Densification of the coating to decrease their sheet resistance enables them to achieve as low as ~ 50 Ω sq-1 for the GNP-based paper. The densification procedure improves the bending stability, the abrasion resistance, and the electromagnetic interference shielding of the paper-based conductors. Finally, the compressed samples show an impressive enhancement of their thermal diffusivity. The flexible and multifunctional nanocarbon coated paper is a promising electronic conductor and thermally dissipative material and, at the same time, can increase the environmental sustainability of the electronics sector.
△ Less
Submitted 23 April, 2020;
originally announced April 2020.
-
Graphene-enabled adaptive infrared textiles
Authors:
M. Said Ergoktas,
Gokhan Bakan,
Pietro Steiner,
Cian Bartlam,
Yury Malevich,
Elif Ozden Yenigun,
Guanliang He,
Nazmul Karim,
Pietro Cataldi,
Mark Bissett,
Ian A. Kinloch,
Kostya S. Novoselov,
Coskun Kocabas
Abstract:
Interactive clothing requires sensing and display functionalities to be embedded on textiles. Despite the significant progress of electronic textiles, the integration of optoelectronic materials on fabrics still remains as an outstanding challenge. Here, using the electro-optical tunability of graphene, we report adaptive optical textiles with electrically controlled reflectivity and emissivity co…
▽ More
Interactive clothing requires sensing and display functionalities to be embedded on textiles. Despite the significant progress of electronic textiles, the integration of optoelectronic materials on fabrics still remains as an outstanding challenge. Here, using the electro-optical tunability of graphene, we report adaptive optical textiles with electrically controlled reflectivity and emissivity covering the infrared and near-infrared wavelengths. We achieve electro-optical modulation by reversible intercalation of ions into graphene layers laminated on fabrics. We demonstrate a new class of infrared textile devices including display, yarn and stretchable devices using natural and synthetic textiles. To show the promise of our approach, we fabricated an active device directly onto a t-shirt which enables long-wavelength infrared communication via modulation of the thermal radiation from the human body. The results presented here, provide complementary technologies which could leverage the ubiquitous use of functional textiles.
△ Less
Submitted 18 April, 2020;
originally announced April 2020.
