-
End benches scattered light modeling and subtraction in Advanced Virgo
Authors:
Michal Was,
Romain Gouaty,
Romain Bonnand
Abstract:
Advanced Virgo end benches were a significant source of scattered light noise during the third observing run that lasted from April 1 2019 until March 27 2020. We describe how that noise could be subtracted using auxiliary channels during the online strain data reconstruction. We model in detail the scattered light noise coupling and demonstrate that further noise subtraction can be achieved. We a…
▽ More
Advanced Virgo end benches were a significant source of scattered light noise during the third observing run that lasted from April 1 2019 until March 27 2020. We describe how that noise could be subtracted using auxiliary channels during the online strain data reconstruction. We model in detail the scattered light noise coupling and demonstrate that further noise subtraction can be achieved. We also show that the fitted model parameters can be used to optically characterized the interferometer and in particular provide a novel way of establishing an absolute calibration of the detector strain data.
△ Less
Submitted 18 February, 2021; v1 submitted 6 November, 2020;
originally announced November 2020.
-
Upper-limit on the Advanced Virgo output mode cleaner cavity length noise
Authors:
R Bonnand,
M Ducrot,
R Gouaty,
F Marion,
A Masserot,
B Mours,
E Pacaud,
L Rolland,
M Was
Abstract:
The Advanced Virgo detector uses two monolithic optical cavities at its output port to suppress higher order modes and radio frequency sidebands from the carrier light used for gravitational wave detection. These two cavities in series form the output mode cleaner. We present a measured upper limit on the length noise of these cavities that is consistent with the thermo-refractive noise prediction…
▽ More
The Advanced Virgo detector uses two monolithic optical cavities at its output port to suppress higher order modes and radio frequency sidebands from the carrier light used for gravitational wave detection. These two cavities in series form the output mode cleaner. We present a measured upper limit on the length noise of these cavities that is consistent with the thermo-refractive noise prediction of $8 \times 10^{-16}\,\textrm{m/Hz}^{1/2}$ at 15 Hz. The cavity length is controlled using Peltier cells and piezo-electric actuators to maintain resonance on the incoming light. A length lock precision of $3.5 \times 10^{-13}\,\textrm{m}$ is achieved. These two results are combined to demonstrate that the broadband length noise of the output mode cleaner in the 10-60 Hz band is at least a factor 10 below other expected noise sources in the Advanced Virgo detector design configuration.
△ Less
Submitted 11 July, 2017; v1 submitted 5 March, 2017;
originally announced March 2017.
-
Advanced Virgo: a 2nd generation interferometric gravitational wave detector
Authors:
F. Acernese,
M. Agathos,
K. Agatsuma,
D. Aisa,
N. Allemandou,
A. Allocca,
J. Amarni,
P. Astone,
G. Balestri,
G. Ballardin,
F. Barone,
J. -P. Baronick,
M. Barsuglia,
A. Basti,
F. Basti,
Th. S. Bauer,
V. Bavigadda,
M. Bejger,
M. G. Beker,
C. Belczynski,
D. Bersanetti,
A. Bertolini,
M. Bitossi,
M. A. Bizouard,
S. Bloemen
, et al. (209 additional authors not shown)
Abstract:
Advanced Virgo is the project to upgrade the Virgo interferometric detector of gravitational waves, with the aim of increasing the number of observable galaxies (and thus the detection rate) by three orders of magnitude. The project is now in an advanced construction phase and the assembly and integration will be completed by the end of 2015. Advanced Virgo will be part of a network with the two A…
▽ More
Advanced Virgo is the project to upgrade the Virgo interferometric detector of gravitational waves, with the aim of increasing the number of observable galaxies (and thus the detection rate) by three orders of magnitude. The project is now in an advanced construction phase and the assembly and integration will be completed by the end of 2015. Advanced Virgo will be part of a network with the two Advanced LIGO detectors in the US and GEO HF in Germany, with the goal of contributing to the early detections of gravitational waves and to opening a new observation window on the universe. In this paper we describe the main features of the Advanced Virgo detector and outline the status of the construction.
△ Less
Submitted 16 October, 2014; v1 submitted 18 August, 2014;
originally announced August 2014.
-
Reconstruction of the gravitational wave signal $h(t)$ during the Virgo science runs and independent validation with a photon calibrator
Authors:
Virgo collaboration,
T. Accadia,
F. Acernese,
M. Agathos,
A. Allocca,
P. Astone,
G. Ballardin,
F. Barone,
M. Barsuglia,
A. Basti,
Th. S. Bauer,
M. Bejger,
M . G. Beker,
C. Belczynski,
D. Bersanetti,
A. Bertolini,
M. Bitossi,
M. A. Bizouard,
M. Blom,
M. Boer,
F. Bondu,
L. Bonelli,
R. Bonnand,
V. Boschi,
L. Bosi
, et al. (171 additional authors not shown)
Abstract:
The Virgo detector is a kilometer-scale interferometer for gravitational wave detection located near Pisa (Italy). About 13 months of data were accumulated during four science runs (VSR1, VSR2, VSR3 and VSR4) between May 2007 and September 2011, with increasing sensitivity.
In this paper, the method used to reconstruct, in the range 10 Hz-10 kHz, the gravitational wave strain time series $h(t)$…
▽ More
The Virgo detector is a kilometer-scale interferometer for gravitational wave detection located near Pisa (Italy). About 13 months of data were accumulated during four science runs (VSR1, VSR2, VSR3 and VSR4) between May 2007 and September 2011, with increasing sensitivity.
In this paper, the method used to reconstruct, in the range 10 Hz-10 kHz, the gravitational wave strain time series $h(t)$ from the detector signals is described. The standard consistency checks of the reconstruction are discussed and used to estimate the systematic uncertainties of the $h(t)$ signal as a function of frequency. Finally, an independent setup, the photon calibrator, is described and used to validate the reconstructed $h(t)$ signal and the associated uncertainties.
The uncertainties of the $h(t)$ time series are estimated to be 8% in amplitude. The uncertainty of the phase of $h(t)$ is 50 mrad at 10 Hz with a frequency dependence following a delay of 8 $μ$s at high frequency. A bias lower than $4\,\mathrm{μs}$ and depending on the sky direction of the GW is also present.
△ Less
Submitted 3 July, 2014; v1 submitted 23 January, 2014;
originally announced January 2014.
-
Calibration and sensitivity of the Virgo detector during its second science run
Authors:
The Virgo Collaboration,
T. Accadia,
F. Acernese,
F. Antonucci,
P. Astone,
G. Ballardin,
F. Barone,
M. Barsuglia,
A. Basti,
Th. S. Bauer,
M. G. Beker,
A. Belletoile,
S. Birindelli,
M. Bitossi,
M. A. Bizouard,
M. Blom,
F. Bondu,
L. Bonelli,
R. Bonnand,
V. Boschi,
L. Bosi,
B. Bouhou,
S. Braccini,
C. Bradaschia,
A. Brillet
, et al. (153 additional authors not shown)
Abstract:
The Virgo detector is a kilometer-length interferometer for gravitational wave detection located near Pisa (Italy). During its second science run (VSR2) in 2009, six months of data were accumulated with a sensitivity close to its design. In this paper, the methods used to determine the parameters for sensitivity estimation and gravitational wave reconstruction are described. The main quantities to…
▽ More
The Virgo detector is a kilometer-length interferometer for gravitational wave detection located near Pisa (Italy). During its second science run (VSR2) in 2009, six months of data were accumulated with a sensitivity close to its design. In this paper, the methods used to determine the parameters for sensitivity estimation and gravitational wave reconstruction are described. The main quantities to be calibrated are the frequency response of the mirror actuation and the sensing of the output power. Focus is also put on their absolute timing. The monitoring of the calibration data as well as the parameter estimation with independent techniques are discussed to provide an estimation of the calibration uncertainties. Finally, the estimation of the Virgo sensitivity in the frequency-domain is described and typical sensitivities measured during VSR2 are shown.
△ Less
Submitted 18 January, 2011; v1 submitted 27 September, 2010;
originally announced September 2010.
