-
High efficiency muon registration system based on scintillator strips
Authors:
A. Artikov,
V. Baranov,
A. Boikov,
D. Chokheli,
Yu. I. Davydov,
V. Glagolev,
A. Simonenko,
Z. Tsamalaidze,
I. Vasilyev,
I. Zimin
Abstract:
Experiments such as mu2e (FNAL, USA) and COMET (KEK, Japan), seeking the direct muon-to-electron conversion as part of the study of Charged Leptons Flavor Violation processes, should have a extremely high, up-to 99.99\%, efficiency muon detection system with a view to their subsequent suppression as background. In this article, the possibility to achieve such efficiency for a short and long term i…
▽ More
Experiments such as mu2e (FNAL, USA) and COMET (KEK, Japan), seeking the direct muon-to-electron conversion as part of the study of Charged Leptons Flavor Violation processes, should have a extremely high, up-to 99.99\%, efficiency muon detection system with a view to their subsequent suppression as background. In this article, the possibility to achieve such efficiency for a short and long term is discussed for modules based on 7- or 10-mm-thick but same 40-mm-wide plastic scintillation strips with single 1.2 mm WLS fiber glued into the groove along the strip and using MPPC/SiPM for light detection.
A Simplified Light Yield Distribution method to estimate the efficiency of the module was proposed and the simulation results obtained with GEANT 4 for a system based on a 4-by-4 array of 7x40x3000 mm strips compared with the experimental data. Found that for the systems required the high level registration efficiency at the 99.99\% and more, it is important to improve the light yield as much as possible and achieve the gap between neighbor scintillation volumes as small as possible.
△ Less
Submitted 3 October, 2023; v1 submitted 25 September, 2023;
originally announced September 2023.
-
Suppression of the slow component of BaF$_{2}$ crystal luminescence with a thin multilayer filter
Authors:
A. M. Artikov,
V. Baranov,
J. A. Budagov,
A. N. Chivanov,
Yuri Davydov,
E. N. Eliseev,
E. A. Garibin,
V. V. Glagolev,
A. V. Mihailov,
P. A. Rodnyi,
V. V. Terechschenko,
I. I. Vasilyev
Abstract:
The fast component of the barium fluoride (BaF$_{2}$) crystal luminescence with the emission peak at 220 nm allows those crystals to be employed in fast calorimeters operating in harsh radiation environment. However, the slow component with the emission peak at 330 nm and about 85\% of the total emission light could create big problems when working at a high radiation rate.
In this work we repor…
▽ More
The fast component of the barium fluoride (BaF$_{2}$) crystal luminescence with the emission peak at 220 nm allows those crystals to be employed in fast calorimeters operating in harsh radiation environment. However, the slow component with the emission peak at 330 nm and about 85\% of the total emission light could create big problems when working at a high radiation rate.
In this work we report results of tests of multilayer filters that can suppress luminescence in the range from 250 nm to 400 nm, which covers most of the BaF$_{2}$ slow component luminescence. The filters are made by spraying layers of rare earth oxides on a quartz glass substrate. Filters typically comprise 200-220 layers.
A few filters were prepared by spraying thin layers on quartz glass. The filters have a peak transmittance of about 70-80\% in the range of 200-250 nm. Measurements of the light output of the BaF$_{2}$ crystal with and without a filter between the crystal readout end and the PMT demonstrate substancial suppression of the slow component. To our knowledge, this kind of filters are produced and tested for the first time.
△ Less
Submitted 5 September, 2018;
originally announced September 2018.
-
Expression of Interest for Evolution of the Mu2e Experiment
Authors:
F. Abusalma,
D. Ambrose,
A. Artikov,
R. Bernstein,
G. C. Blazey,
C. Bloise,
S. Boi,
T. Bolton,
J. Bono,
R. Bonventre,
D. Bowring,
D. Brown,
D. Brown,
K. Byrum,
M. Campbell,
J. -F. Caron,
F. Cervelli,
D. Chokheli,
K. Ciampa,
R. Ciolini,
R. Coleman,
D. Cronin-Hennessy,
R. Culbertson,
M. A. Cummings,
A. Daniel
, et al. (103 additional authors not shown)
Abstract:
We propose an evolution of the Mu2e experiment, called Mu2e-II, that would leverage advances in detector technology and utilize the increased proton intensity provided by the Fermilab PIP-II upgrade to improve the sensitivity for neutrinoless muon-to-electron conversion by one order of magnitude beyond the Mu2e experiment, providing the deepest probe of charged lepton flavor violation in the fores…
▽ More
We propose an evolution of the Mu2e experiment, called Mu2e-II, that would leverage advances in detector technology and utilize the increased proton intensity provided by the Fermilab PIP-II upgrade to improve the sensitivity for neutrinoless muon-to-electron conversion by one order of magnitude beyond the Mu2e experiment, providing the deepest probe of charged lepton flavor violation in the foreseeable future. Mu2e-II will use as much of the Mu2e infrastructure as possible, providing, where required, improvements to the Mu2e apparatus to accommodate the increased beam intensity and cope with the accompanying increase in backgrounds.
△ Less
Submitted 7 February, 2018;
originally announced February 2018.
-
Light yield and radiation hardness studies of scintillator strips with a filler
Authors:
A. Artikov,
V. Baranov,
Yu. Budagov,
M. Bulavin,
D. Chokheli,
Yu. I Davydov,
V. Glagolev,
Yu. Kharzheev,
V. Kolomoets,
A. Simonenko,
Z. Usubov,
I. Vasiljev
Abstract:
Detectors based on polystyrene scintillator strips with WLS fiber readout are widely used to register charged particles in many high-energy physics experiments. The fibers are placed into grooves or holes along the strip. The detection efficiency of these devices can be significantly increased by improving the optical contact between the scintillator and the fiber by adding an optical filler into…
▽ More
Detectors based on polystyrene scintillator strips with WLS fiber readout are widely used to register charged particles in many high-energy physics experiments. The fibers are placed into grooves or holes along the strip. The detection efficiency of these devices can be significantly increased by improving the optical contact between the scintillator and the fiber by adding an optical filler into the groove/hole.
This work is devoted to the study of the light yield of a 5-m-long scintillator strip with a 1.2-mm-diameter Kuraray Y11(200)~MC WLS fiber inserted into the strip's co-extruded hole filled with synthetic silicon resin SKTN-MED(E). The light yield was studied using cosmic muons and a $^{60}$Co radioactive source.
Radiation hardness study of viscous fillers and short strip samples were performed on the IBR-2 pulsed research reactor of fast neutrons at JINR.
△ Less
Submitted 6 August, 2018; v1 submitted 30 November, 2017;
originally announced November 2017.
-
Photoelectron Yields of Scintillation Counters with Embedded Wavelength-Shifting Fibers Read Out With Silicon Photomultipliers
Authors:
Akram Artikov,
Vladimir Baranov,
Gerald C. Blazey,
Ningshun Chen,
Davit Chokheli,
Yuri Davydov,
E. Craig Dukes,
Alexsander Dychkant,
Ralf Ehrlich,
Kurt Francis,
M. J. Frank,
Vladimir Glagolev,
Craig Group,
Sten Hansen,
Stephen Magill,
Yuri Oksuzian,
Anna Pla-Dalmau,
Paul Rubinov,
Aleksandr Simonenko,
Enhao Song,
Steven Stetzler,
Yongyi Wu,
Sergey Uzunyan,
Vishnu Zutshi
Abstract:
Photoelectron yields of extruded scintillation counters with titanium dioxide coating and embedded wavelength shifting fibers read out by silicon photomultipliers have been measured at the Fermilab Test Beam Facility using 120\,GeV protons. The yields were measured as a function of transverse, longitudinal, and angular positions for a variety of scintillator compositions and reflective coating mix…
▽ More
Photoelectron yields of extruded scintillation counters with titanium dioxide coating and embedded wavelength shifting fibers read out by silicon photomultipliers have been measured at the Fermilab Test Beam Facility using 120\,GeV protons. The yields were measured as a function of transverse, longitudinal, and angular positions for a variety of scintillator compositions and reflective coating mixtures, fiber diameters, and photosensor sizes. Timing performance was also studied. These studies were carried out by the Cosmic Ray Veto Group of the Mu2e collaboration as part of their R\&D program.
△ Less
Submitted 5 February, 2018; v1 submitted 19 September, 2017;
originally announced September 2017.
-
The increase of the light collection from scintillation strip with hole for WLS fiber using various types of fillers
Authors:
A. Simonenko,
A. Artikov,
V. Baranov,
J. Budagov,
D. Chokheli,
Yu. Davydov,
V. Glagolev,
Yu. Kharzheev,
V. Kolomoetz,
A. Shalyugin,
V. Tereschenko
Abstract:
The light collection of the extruded scintillator strip samples with WLS fibers placed in the longitudinal hole in the plates was measured. The holes were filled with various liquid fillers. Measurements were carried out under irradiation by cosmic muons. The method of pum** liquid filler with viscosity more than 10 Pa*s in the strip hole with WLS fiber inside was designed and successfully teste…
▽ More
The light collection of the extruded scintillator strip samples with WLS fibers placed in the longitudinal hole in the plates was measured. The holes were filled with various liquid fillers. Measurements were carried out under irradiation by cosmic muons. The method of pum** liquid filler with viscosity more than 10 Pa*s in the strip hole with WLS fiber inside was designed and successfully tested.
△ Less
Submitted 8 April, 2016;
originally announced April 2016.
-
Optimization of light yield by injection of the optical filler into the co extruded hole of plastic scintillation bar with WLS fiber in it
Authors:
A. Artikov,
V. Baranov,
Yu. Budagov,
D. Chokheli,
Yu. Davydov,
V. Glagolev,
Yu. Kharzheev,
V. Kolomoetz,
A. Shalugin,
A. Simonenko,
V. Tereshchenko
Abstract:
Results of the measurements with cosmic muons for the light yield of 2-meter long extruded scintillation bar (strip) as a function of distance for different options for light collection technique are presented. Scintillation strip cross section geometry was a triangle made on polystyrene plastic scintillator with dopants of 2% PTP and 0.03% POPOP, extruded with 2.6 mm diameter hole and produced at…
▽ More
Results of the measurements with cosmic muons for the light yield of 2-meter long extruded scintillation bar (strip) as a function of distance for different options for light collection technique are presented. Scintillation strip cross section geometry was a triangle made on polystyrene plastic scintillator with dopants of 2% PTP and 0.03% POPOP, extruded with 2.6 mm diameter hole and produced at ISMA (Kharkov, Ukraine). It was shown that the insertion of the optical transparent resin (BC 600 or CKTN MED(E)) by special technique into the co-extruded hole with 1.0 mm or 1.2 mm wave-length shifter (WLS) fiber Kuraray Y11 (200) MC in it significantly improves light collection by factor of 1.6...1.9 against of the 'dry' case.
△ Less
Submitted 8 April, 2016;
originally announced April 2016.
-
Performance of Scintillator Counters with Silicon Photomultiplier Readout
Authors:
Mu2e Collaboration Cosmic Ray Veto Group,
A. Artikov,
V. Baranov,
D. Chokheli,
Yu. I. Davydov,
E. C. Dukes,
R. Ehrlich,
K. Francis,
M. J. Frank,
V. Glagolev,
R. C. Group,
S. Hansen,
A. Hocker,
Y. Oksuzian,
P. Rubinov,
E. Song,
S. Uzunyan,
Y. Wu
Abstract:
The performance of scintillator counters with embedded wavelength-shifting fibers has been measured in the Fermilab Meson Test Beam Facility using 120 GeV protons. The counters were extruded with a titanium dioxide surface coating and two channels for fibers at the Fermilab NICADD facility. Each fiber end is read out by a 2*2 mm^2 silicon photomultiplier. The signals were amplified and digitized b…
▽ More
The performance of scintillator counters with embedded wavelength-shifting fibers has been measured in the Fermilab Meson Test Beam Facility using 120 GeV protons. The counters were extruded with a titanium dioxide surface coating and two channels for fibers at the Fermilab NICADD facility. Each fiber end is read out by a 2*2 mm^2 silicon photomultiplier. The signals were amplified and digitized by a custom-made front-end electronics board. Combinations of 5*2 cm^2 and 6*2 cm^2 extrusion profiles with 1.4 and 1.8 mm diameter fibers were tested. The design is intended for the cosmic-ray veto detector for the Mu2e experiment at Fermilab. The light yield as a function of the transverse and longitudinal position of the beam will be given.
△ Less
Submitted 1 November, 2015;
originally announced November 2015.
-
Mu2e Technical Design Report
Authors:
L. Bartoszek,
E. Barnes,
J. P. Miller,
J. Mott,
A. Palladino,
J. Quirk,
B. L. Roberts,
J. Crnkovic,
V. Polychronakos,
V. Tishchenko,
P. Yamin,
C. -h. Cheng,
B. Echenard,
K. Flood,
D. G. Hitlin,
J. H. Kim,
T. S. Miyashita,
F. C. Porter,
M. Röhrken,
J. Trevor,
R. -Y. Zhu,
E. Heckmaier,
T. I. Kang,
G. Lim,
W. Molzon
, et al. (238 additional authors not shown)
Abstract:
The Mu2e experiment at Fermilab will search for charged lepton flavor violation via the coherent conversion process mu- N --> e- N with a sensitivity approximately four orders of magnitude better than the current world's best limits for this process. The experiment's sensitivity offers discovery potential over a wide array of new physics models and probes mass scales well beyond the reach of the L…
▽ More
The Mu2e experiment at Fermilab will search for charged lepton flavor violation via the coherent conversion process mu- N --> e- N with a sensitivity approximately four orders of magnitude better than the current world's best limits for this process. The experiment's sensitivity offers discovery potential over a wide array of new physics models and probes mass scales well beyond the reach of the LHC. We describe herein the preliminary design of the proposed Mu2e experiment. This document was created in partial fulfillment of the requirements necessary to obtain DOE CD-2 approval.
△ Less
Submitted 16 March, 2015; v1 submitted 21 January, 2015;
originally announced January 2015.
-
Mu2e Conceptual Design Report
Authors:
The Mu2e Project,
Collaboration,
:,
R. J. Abrams,
D. Alezander,
G. Ambrosio,
N. Andreev,
C. M. Ankenbrandt,
D. M. Asner,
D. Arnold,
A. Artikov,
E. Barnes,
L. Bartoszek,
R. H. Bernstein,
K. Biery,
V. Biliyar,
R. Bonicalzi,
R. Bossert,
M. Bowden,
J. Brandt,
D. N. Brown,
J. Budagov,
M. Buehler,
A. Burov,
R. Carcagno
, et al. (203 additional authors not shown)
Abstract:
Mu2e at Fermilab will search for charged lepton flavor violation via the coherent conversion process mu- N --> e- N with a sensitivity approximately four orders of magnitude better than the current world's best limits for this process. The experiment's sensitivity offers discovery potential over a wide array of new physics models and probes mass scales well beyond the reach of the LHC. We describe…
▽ More
Mu2e at Fermilab will search for charged lepton flavor violation via the coherent conversion process mu- N --> e- N with a sensitivity approximately four orders of magnitude better than the current world's best limits for this process. The experiment's sensitivity offers discovery potential over a wide array of new physics models and probes mass scales well beyond the reach of the LHC. We describe herein the conceptual design of the proposed Mu2e experiment. This document was created in partial fulfillment of the requirements necessary to obtain DOE CD-1 approval, which was granted July 11, 2012.
△ Less
Submitted 29 November, 2012;
originally announced November 2012.
-
CDF Central Preshower and Crack Detector Upgrade
Authors:
A. Artikov
Abstract:
The CDF Central Preshower and Crack Detector Upgrade consist of scintillator tiles with embedded wavelength-shifting fibers, clear-fiber optical cables, and multi-anode photomultiplier readout. A description of the detector design, test results from R&D studies, and construction phase are reported. The upgrade was installed late in 2004, and a large amount of proton-antiproton collider data has…
▽ More
The CDF Central Preshower and Crack Detector Upgrade consist of scintillator tiles with embedded wavelength-shifting fibers, clear-fiber optical cables, and multi-anode photomultiplier readout. A description of the detector design, test results from R&D studies, and construction phase are reported. The upgrade was installed late in 2004, and a large amount of proton-antiproton collider data has been collected since then. Detector studies using those data are also discussed.
△ Less
Submitted 26 June, 2007;
originally announced June 2007.
-
Design and construction of new central and forward muon counters for CDF II
Authors:
A. Artikov,
J. Budagov,
G. Bellettini
Abstract:
New scintillation counters have been designed and constructed for the CDF upgrade in order to complete the muon coverage of the central CDF detector, and to extend this coverage to larger pseudorapidity. A novel light collection technique using wavelength shifting fibers, together with high quality polystyrene-based scintillator resulted in compact counters with good and stable light collection…
▽ More
New scintillation counters have been designed and constructed for the CDF upgrade in order to complete the muon coverage of the central CDF detector, and to extend this coverage to larger pseudorapidity. A novel light collection technique using wavelength shifting fibers, together with high quality polystyrene-based scintillator resulted in compact counters with good and stable light collection efficiency over lengths extending up to 320 cm. Their design and construction is described and results of their initial performance are reported.
△ Less
Submitted 15 March, 2004;
originally announced March 2004.
