-
Performance of small-diameter muon drift tube chambers with new fast readout ASIC at high background rates
Authors:
Sergey Abovyan,
Nayana Bangaru,
Francesco Fallavollita,
Oliver Kortner,
Sandra Kortner,
Hubert Kroha,
Elena Voevodina,
Robert Richter,
Yazhou Zhao
Abstract:
Experiments like ATLAS at the HL-LHC or detectors at future hadron colliders need muon detectors with excellent momentum resolution up to the TeV scale both at the trigger and offline reconstruction levels. This requires muon tracking chambers with high spatial resolution even at the highest background fluxes. Drift-tube chambers are the most cost-effective technology for large-area muon systems,…
▽ More
Experiments like ATLAS at the HL-LHC or detectors at future hadron colliders need muon detectors with excellent momentum resolution up to the TeV scale both at the trigger and offline reconstruction levels. This requires muon tracking chambers with high spatial resolution even at the highest background fluxes. Drift-tube chambers are the most cost-effective technology for large-area muon systems, providing the required high rate capability and three-dimensional spatial resolution. Thanks to advances in electronics, the new generation small-diameter Muon Drift Tube (sMDT) detectors with 15 mm tube diameter can be used in stand-alone mode up to the background rates expected at future hadron collider experiments, providing event times and second coordinates without additional trigger chambers. New developments in integrated front-end electronics include fast baseline restoration of the shaped signal and picosecond time-to-digital converters for second coordinate measurement with double-sided read-out. Self-triggered operation is now possible using modern high-performance FPGAs for real-time pattern recognition and track reconstruction. A new amplifier shaper discriminator chip in 65 nm TSMC CMOS technology with increased sensitivity and faster baseline recovery has been developed to cope with high background fluxes. Extensive test beam campaigns using sMDT chambers with new readout electronics have been performed at the CERN Gamma Irradiation Facility (GIF++). Results show that the shorter peaking time of the new chip enhances the spatial resolution of the drift tubes by up to 100 $μ$m at a background rate of 1 MHz, the maximum rate expected at the 100 TeV collider experiment.
△ Less
Submitted 3 July, 2024; v1 submitted 1 July, 2024;
originally announced July 2024.
-
Commissioning and installation of the new small-Diameter Muon Drift Tube (sMDT) detectors for the Phase-I upgrade of the ATLAS Muon Spectrometer
Authors:
G. H. Eberwein,
O. Kortner,
H. Kroha,
M. Rendel,
P. Rieck,
D. Soyk,
E. Voevodina,
V. Walbrecht
Abstract:
The Monitored Drift Tubes, as a part of the ATLAS muon spectrometer, are precision drift chambers designed to provide excellent spatial resolution and high tracking efficiency independent of the track angle. Through the life of the LHC and ATLAS experiment, this detector has already demonstrated that they provide precise tracking over large areas. The aim of the ATLAS muon spectrometer upgrade is…
▽ More
The Monitored Drift Tubes, as a part of the ATLAS muon spectrometer, are precision drift chambers designed to provide excellent spatial resolution and high tracking efficiency independent of the track angle. Through the life of the LHC and ATLAS experiment, this detector has already demonstrated that they provide precise tracking over large areas. The aim of the ATLAS muon spectrometer upgrade is to increase the muon trigger efficiency, precise muon momentum measurement and to improve the rate capability of the muon system in the high-background regions during the High-Luminosity LHC runs. To meet these requirements, the proposed solution is based on the small (15 mm) diameter Muon Drift Tube chamber (sMDT) technology. The new detector provides about an order of magnitude higher rate capability and allows for the installation of additional new triplet Resistive Plate Chambers (RPCs) trigger detectors in the barrel inner layer of the muon system. A pilot project for the barrel inner layer upgrade is underway during the 2019/21 LHC shutdown. For this reason, the Max-Planck-Institute for Physics in Munich has built 16 sMDT chambers, each will cover an area of about 2.5 $m^{2}$. To ensure their proper operation in the experiment, the sMDT detectors have to pass a set of stringent tests both at the production site and after their delivery at CERN. After their installation in the ATLAS muon spectrometer, the muon stations are further tested and commissioned with cosmic rays. The author will describe the detector design, the quality assurance and certification path, as well as will present the experience with the chamber tests, the integration procedure and installation of the muon stations in the ATLAS experiment.
△ Less
Submitted 13 December, 2021;
originally announced December 2021.
-
Performance of the new Readout Electronics for the ATLAS (s)MDT Chambers and Future Colliders at High Background Rates
Authors:
G. H. Eberwein,
O. Kortner,
H. Kroha,
E. Voevodina
Abstract:
Small-diameter Drift Tube (sMDT) detectors with 15 mm tube diameter have proven to be excellent candidates for precision muon tracking detectors in experiments at future hadron colliders like HL-LHC and FCC-hh where unprecedentedly high background rate capabilities are required. sMDT chambers are currently being installed in the inner barrel layer of the ATLAS muon spectrometer. The rate capabilit…
▽ More
Small-diameter Drift Tube (sMDT) detectors with 15 mm tube diameter have proven to be excellent candidates for precision muon tracking detectors in experiments at future hadron colliders like HL-LHC and FCC-hh where unprecedentedly high background rate capabilities are required. sMDT chambers are currently being installed in the inner barrel layer of the ATLAS muon spectrometer. The rate capability of the sMDT drift tubes in terms of muon detection efficiency and spatial resolution is limited by the performance of the readout electronics. A new (s)MDT ASD (Amplifier-Shaper-Discriminator) readout chip for use at the HL-LHC and future hadron colliders with a faster peaking time compared to the old chip has been developed, reducing the discriminator threshold crossing time jitter and thus improving the time- and spatial resolution with and without $γ$-background radiation. Additionally, a method compensating the gas gain drop due to space charge at high $γ$-background hit flux by adjusting the sMDT operating voltage will be presented. Simulations show, that the addition of active baseline restoration circuits in the front-end electronics chips in order to suppress signal-pile-up effects at high counting rates further leads to significant improvement of both efficiency and resolution. Extensive tests using sMDT test chambers have been performed at the CERN Gamma Irradiation Facility (GIF++). Chambers equipped with new readout chips with improved pulse sha** and discrete readout circuits with baseline restoring functionality have been tested.
△ Less
Submitted 9 December, 2021;
originally announced December 2021.
-
Hardware Demonstrator of a Compact First-Level Muon Track Trigger for Future Hadron Collider Experiments
Authors:
D. Cieri,
S. Abovyan,
V. Danielyan,
M. Fras,
P. Gadow,
O. Kortner,
S. Kortner,
H. Kroha,
F. Müller,
S. Nowak,
P. Richter,
K. Schmidt-Sommerfeld
Abstract:
Single muon triggers are crucial for the physics programmes at hadron collider experiments. To be sensitive to electroweak processes, single muon triggers with transverse momentum thresholds down to 20 GeV and dimuon triggers with even lower thresholds are required. In order to keep the rates of these triggers at an acceptable level these triggers have to be highly selective, i.e. they must have s…
▽ More
Single muon triggers are crucial for the physics programmes at hadron collider experiments. To be sensitive to electroweak processes, single muon triggers with transverse momentum thresholds down to 20 GeV and dimuon triggers with even lower thresholds are required. In order to keep the rates of these triggers at an acceptable level these triggers have to be highly selective, i.e. they must have small accidental trigger rates and sharp trigger turn-on curves. The muon systems of the LHC experiments and experiments at future colliders like FCC-hh will use two muon chamber systems for the muon trigger, fast trigger chambers like RPCs with coarse spatial resolution and much slower precision chambers like drift-tube chambers with high spatial resolution. The data of the trigger chambers are used to identify the bunch crossing in which the muon was created and for a rough momentum measurement while the precise measurements of the muon trajectory by the precision chambers are ideal for an accurate muon momentum measurement. A compact muon track finding algorithm is presented, where muon track candidates are reconstructed using a binning algorithm based on a 1D Hough Transform. The algorithm has been designed and implemented on a System-On-Chip device. A hardware demonstration using Xilinx Evaluation boards ZC706 has been set-up to prove the concept. The system has demonstrated the feasibility to reconstruct muon tracks with a good angular resolution, whilst satisfying latency constraints. The demonstrated track-reconstruction system, the chosen architecture, the achievements to date and future options for such a system will be discussed.
△ Less
Submitted 11 February, 2019;
originally announced February 2019.
-
Hardware Implementation of a Fast Algorithm for the Reconstruction of Muon Tracks in ATLAS Muon Drift-Tube Chambers for the First-Level Muon Trigger at the HL-LHC
Authors:
Sergey Abovyan,
Varuzhan Danielyan,
Markus Fras,
Philipp Gadow,
Oliver Kortner,
Sandra Kortner,
Hubert Kroha,
Felix Müller,
Sebastian Nowak,
Robert Richter,
Korbinian Schmidt-Sommerfeld
Abstract:
The High-Luminosity LHC will provide the unique opportunity to explore the nature of physics beyond the Standard Model of strong and electroweak interactions. Highly selective first level triggers are essential for the physics programme of the ATLAS experiment at the HL-LHC where the instantaneous luminosity will exceed the LHC Run 1 instantaneous luminosity by almost an order of magnitude. The AT…
▽ More
The High-Luminosity LHC will provide the unique opportunity to explore the nature of physics beyond the Standard Model of strong and electroweak interactions. Highly selective first level triggers are essential for the physics programme of the ATLAS experiment at the HL-LHC where the instantaneous luminosity will exceed the LHC Run 1 instantaneous luminosity by almost an order of magnitude. The ATLAS first level muon trigger rate is dominated by low momentum muons, selected due to the moderate momentum resolution of the resistive plate and thin gap trigger chambers. This limitation can be overcome by including the data of the precision muon drift tube (MDT) chambers in the first level trigger decision. This requires the fast continuous transfer of the MDT hits to the off-detector trigger logic and a fast track reconstruction algorithm performed in the trigger logic.
In order to demonstrate the feasibility of reconstructing tracks in MDT chambers within the short available first-level trigger latency of about 3~$μ$s we implemented a seeded Hough transform on the ARM Cortex A9 microprocessor of a Xilinx Zynq FPGA and studied its performance with test-beam data recorded in CERN's Gamma Irradiation Facility. We could show that by using the ARM processor's Neon Single Instruction Multiple Data Engine to carry out 4 floating point operations in parallel the challenging latency requirement can be matched.
△ Less
Submitted 11 March, 2018;
originally announced March 2018.
-
Development of a Highly Selective First-Level Muon Trigger for ATLAS at HL-LHC Exploiting Precision Muon Drift-Tube Data
Authors:
S. Abovyan,
V. Danielyan,
M. Fras,
P. Gadow,
O. Kortner,
S. Kortner,
H. Kroha,
F. Mueller,
S. Nowak,
R. Richter,
K. Schmidt-Sommerfeld
Abstract:
The High-Luminosity LHC (HL-LHC) will provide the unique opportunity to explore the nature of physics beyond the Standard Model of strong and electroweak interactions. Highly selective first-level triggers are essential for the physics programme of the ATLAS experiment at HL-LHC, where the instantaneous luminosity will exceed the instantaneous LHC Run 1 luminosity by about an order of magnitude. T…
▽ More
The High-Luminosity LHC (HL-LHC) will provide the unique opportunity to explore the nature of physics beyond the Standard Model of strong and electroweak interactions. Highly selective first-level triggers are essential for the physics programme of the ATLAS experiment at HL-LHC, where the instantaneous luminosity will exceed the instantaneous LHC Run 1 luminosity by about an order of magnitude. The ATLAS first-level muon trigger rate is dominated by low momentum muons, which are accepted because of the moderate momentum resolution of the RPC and TGC trigger chambers. This limitation can be overcome by exploiting the data of the precision Muon Drift-Tube (MDT) chambers in the first-level trigger decision. This requires continuous fast transfer of the MDT hits to the off-detector trigger logic and fast track reconstruction algorithms. The reduction of the muon trigger rate achievable with the proposed new trigger concept, the performance of a novel fast track reconstruction algorithm, and the first hardware demonstration of the scheme with muon testbeam data taken at the CERN Gamma Irradiation Facility are discussed.
△ Less
Submitted 31 January, 2017;
originally announced January 2017.
-
Performance of New High-Precision Muon Tracking Detectors for the ATLAS Experiment
Authors:
Hubert Kroha,
Oliver Kortner,
Korbinian Schmidt-Sommerfeld,
Eric Takasugi
Abstract:
The goals of the ongoing and planned ATLAS muon detector upgrades are to increase the acceptance for precision muon momentum measurement and triggering and to improve the rate capability of the muon chambers in the high-background regions corresponding to the increasing LHC luminosity. Smalldiameter Muon Drift Tube (sMDT) chambers have been developed for these purposes. With half the drift-tube di…
▽ More
The goals of the ongoing and planned ATLAS muon detector upgrades are to increase the acceptance for precision muon momentum measurement and triggering and to improve the rate capability of the muon chambers in the high-background regions corresponding to the increasing LHC luminosity. Smalldiameter Muon Drift Tube (sMDT) chambers have been developed for these purposes. With half the drift-tube diameter of the current ATLAS Muon Drift Tube (MDT) chambers with 30 mm drift tube diameter and otherwise unchanged operating parameters, the sMDT chambers share all the advantages of the MDTs, but have an about an order of magnitude higher rate capability and can be installed in detector regions where MDT chambers do not fit in. The construction of twelve chambers for the feet regions of the ATLAS detector has been completed for the installation in the winter shutdown 2016/17 of the Large Hadron Collider. The purpose of this upgrade of the ATLAS muon spectrometer is to increase the acceptance for three-point muon track measurement which substantially improves the muon momentum resolution in the regions concerned.
△ Less
Submitted 31 January, 2017;
originally announced January 2017.
-
A Highly Selective First-Level Muon Trigger With MDT Chamber Data for ATLAS at HL-LHC
Authors:
H. Kroha,
S. Nowak
Abstract:
Highly selective triggers are essential for the physics programme of the ATLAS experiment at HL-LHC where the instantaneous luminosity will be about an order of magnitude larger than the LHC instantaneous luminosity in Run 1. The first level muon trigger rate is dominated by low momentum muons below the nominal trigger threshold due to the moderate momentum resolution of the Resistive Plate and Th…
▽ More
Highly selective triggers are essential for the physics programme of the ATLAS experiment at HL-LHC where the instantaneous luminosity will be about an order of magnitude larger than the LHC instantaneous luminosity in Run 1. The first level muon trigger rate is dominated by low momentum muons below the nominal trigger threshold due to the moderate momentum resolution of the Resistive Plate and Thin Gap trigger chambers. The resulting high trigger rates at HL-LHC can be sufficiently reduced by using the data of the precision Muon Drift Tube chambers for the trigger decision. This requires the implementation of a fast MDT read-out chain and of a fast MDT track reconstruction algorithm with a latency of at most 6 microseconds. A hardware demonstrator of the fast read-out chain has been successfully tested at the HL-LHC operating conditions at the CERN Gamma Irradiation Facility. The fast track reconstruction algorithm has been implemented on a fast trigger processor.
△ Less
Submitted 26 April, 2016;
originally announced April 2016.
-
Construction and Test of the Precision Drift Chambers for the ATLAS Muon Spectrometer
Authors:
F. Bauer,
W. Blum,
U. Bratzler,
H. Dietl,
S. Kotov,
H. Kroha,
Th. Lagouri,
A. Manz,
A. Ostapchuk,
R. Richter,
S. Schael,
S. Chouridou,
M. Deile,
O. Kortner,
A. Staude,
R. Stroehmer,
T. Trefzger
Abstract:
The Monitored Drift Tube (MDT) chambers for the muon spectrometer of the ATLAS detector at the Large Hadron Collider (LHC) consist of 3-4 layers of pressurised drift tubes on either side of a space frame carrying an optical deformation monitoring system. The chambers have to provide a track position resolution of 40 microns with a single-tube resolution of at least 80 microns and a sense wire posi…
▽ More
The Monitored Drift Tube (MDT) chambers for the muon spectrometer of the ATLAS detector at the Large Hadron Collider (LHC) consist of 3-4 layers of pressurised drift tubes on either side of a space frame carrying an optical deformation monitoring system. The chambers have to provide a track position resolution of 40 microns with a single-tube resolution of at least 80 microns and a sense wire positioning accu- racy of 20 ?microns (rms). The feasibility was demonstrated with the full-scale prototype of one of the largest MDT chambers with 432 drift tubes of 3.8 m length. For the ATLAS muon spectrometer, 88 chambers of this type have to be built. The first chamber has been completed with a wire positioning accuracy of 14 microns (rms).
△ Less
Submitted 8 April, 2016;
originally announced April 2016.
-
Construction and Test of MDT Chambers for the ATLAS Muon Spectrometer
Authors:
F. Bauer,
U. Bratzler,
H. Dietl,
H. Kroha,
Th. Lagouri,
A. Manz,
A. Ostapchuk,
R. Richter,
S. Schael,
S. Chouridou,
M. Deile,
O. Kortner,
A. Staude,
R. Stroehmer,
T. Trefzger
Abstract:
The Monitored Drift Tube (MDT) chambers for the muon spectrometer of the AT- LAS detector at the Large Hadron Collider (LHC) consist of 3-4 layers of pressurized drift tubes on either side of a space frame carrying an optical monitoring system to correct for deformations. The full-scale prototype of a large MDT chamber has been constructed with methods suitable for large-scale production. X-ray me…
▽ More
The Monitored Drift Tube (MDT) chambers for the muon spectrometer of the AT- LAS detector at the Large Hadron Collider (LHC) consist of 3-4 layers of pressurized drift tubes on either side of a space frame carrying an optical monitoring system to correct for deformations. The full-scale prototype of a large MDT chamber has been constructed with methods suitable for large-scale production. X-ray measurements at CERN showed a positioning accuracy of the sense wires in the chamber of better than the required 20 ?microns (rms). The performance of the chamber was studied in a muon beam at CERN. Chamber production for ATLAS now has started.
△ Less
Submitted 7 April, 2016;
originally announced April 2016.
-
Performance of the ATLAS Muon Drift-Tube Chambers at High Background Rates and in Magnetic Fields
Authors:
J. Dubbert,
S. Horvat,
F. Legger,
O. Kortner,
H. Kroha,
R. Richter,
Ch. Valderanis,
F. Rauscher,
A. Staude
Abstract:
The ATLAS muon spectrometer uses drift-tube chambers for precision tracking. The performance of these chambers in the presence of magnetic field and high radiation fluxes is studied in this article using test-beam data recorded in the Gamma Irradiation Facility at CERN. The measurements are compared to detailed predictions provided by the Garfield drift-chamber simulation programme.
The ATLAS muon spectrometer uses drift-tube chambers for precision tracking. The performance of these chambers in the presence of magnetic field and high radiation fluxes is studied in this article using test-beam data recorded in the Gamma Irradiation Facility at CERN. The measurements are compared to detailed predictions provided by the Garfield drift-chamber simulation programme.
△ Less
Submitted 6 April, 2016;
originally announced April 2016.
-
Large-Scale Production of Monitored Drift Tube Chambers for the ATLAS Muon Spectrometer
Authors:
F. Bauer,
S. Horvat,
O. Kortner,
H. Kroha,
A. Manz,
S. Mohrdieck,
R. Richter,
V. Zhuravlov
Abstract:
Precision drift tube chambers with a sense wire positioning accuracy of better than 20 microns are under construction for the ATLAS muon spectrometer. 70% of the 88 large chambers for the outermost layer of the central part of the spectrometer have been assembled. Measurements during chamber construction of the positions of the sense wires and of the sensors for the optical alignment monitoring sy…
▽ More
Precision drift tube chambers with a sense wire positioning accuracy of better than 20 microns are under construction for the ATLAS muon spectrometer. 70% of the 88 large chambers for the outermost layer of the central part of the spectrometer have been assembled. Measurements during chamber construction of the positions of the sense wires and of the sensors for the optical alignment monitoring system demonstrate that the requirements for the mechanical precision of the chambers are fulfilled.
△ Less
Submitted 1 April, 2016;
originally announced April 2016.
-
Performance of the ATLAS Precision Muon Chambers under LHC Operating Conditions
Authors:
M. Deile,
H. Dietl,
J. Dubbert,
S. Horvat,
O. Kortner,
H. Kroha,
A. Manz,
S. Mohrdieck,
F. Rauscher,
R. Richter,
A. Staude
Abstract:
For the muon spectrometer of the ATLAS detector at the large hadron collider (LHC), large drift chambers consisting of 6 to 8 layers of pressurized drift tubes are used for precision tracking covering an active area of 5000 m2 in the toroidal field of superconducting air core magnets. The chambers have to provide a spatial resolution of 41 microns with Ar:CO2 (93:7) gas mixture at an absolute pres…
▽ More
For the muon spectrometer of the ATLAS detector at the large hadron collider (LHC), large drift chambers consisting of 6 to 8 layers of pressurized drift tubes are used for precision tracking covering an active area of 5000 m2 in the toroidal field of superconducting air core magnets. The chambers have to provide a spatial resolution of 41 microns with Ar:CO2 (93:7) gas mixture at an absolute pressure of 3 bar and gas gain of 2?104. The environment in which the chambers will be operated is characterized by high neutron and background with counting rates of up to 100 per square cm and second. The resolution and efficiency of a chamber from the serial production for ATLAS has been investigated in a 100 GeV muon beam at photon irradiation rates as expected during LHC operation. A silicon strip detector telescope was used as external reference in the beam. The spatial resolution of a chamber is degraded by 4 ?m at the highest background rate. The detection efficiency of the drift tubes is unchanged under irradiation. A tracking efficiency of 98% at the highest rates has been demonstrated.
△ Less
Submitted 1 April, 2016;
originally announced April 2016.
-
Resolution and Efficiency of the ATLAS Muon Drift-Tube Chambers at High Background Rates
Authors:
M. Deile,
J. Dubbert,
S. Horvat,
O. Kortner,
H. Kroha,
A. Manz,
S. Mohrdieck-Moeck,
F. Rauscher,
R. Richter,
A. Staude,
W. Stiller
Abstract:
The resolution and efficiency of a precision drift-tube chamber for the ATLAS muon spectrometer with final read-out electronics was tested at the Gamma Irradiation Facility at CERN in a 100 GeV muon beam and at photon irradiation rates of up to 990 Hz/square cm which corresponds to twice the highest background rate expected in ATLAS. A silicon strip detector telescope was used as external referenc…
▽ More
The resolution and efficiency of a precision drift-tube chamber for the ATLAS muon spectrometer with final read-out electronics was tested at the Gamma Irradiation Facility at CERN in a 100 GeV muon beam and at photon irradiation rates of up to 990 Hz/square cm which corresponds to twice the highest background rate expected in ATLAS. A silicon strip detector telescope was used as external reference in the beam. The pulse-height measurement of the read-out electronics was used to perform time-slewing corrections which lead to an improvement of the average drift-tube resolution from 104 microns to 82 microns without irradiation and from 128 microns to 108 microns at the maximum expected rate. The measured drift-tube efficiency agrees with the expectation from the dead time of the read-out electronics up to the maximum expected rate.
△ Less
Submitted 31 March, 2016;
originally announced March 2016.
-
Upgrades of the ATLAS Muon Spectrometer with sMDT Chambers
Authors:
C. Ferretti,
H. Kroha
Abstract:
With half the drift-tube diameter of the Monitored Drift Tube (MDT) chambers of the ATLAS muon spectrometer and otherwise unchanged operating parameters, small-diameter Muon Drift Tube (sMDT) chambers provide an order of magnitude higher rate capability and can be installed in detector regions where MDT chambers do not fit. The chamber assembly time has been reduced by a factor of seven to one wor…
▽ More
With half the drift-tube diameter of the Monitored Drift Tube (MDT) chambers of the ATLAS muon spectrometer and otherwise unchanged operating parameters, small-diameter Muon Drift Tube (sMDT) chambers provide an order of magnitude higher rate capability and can be installed in detector regions where MDT chambers do not fit. The chamber assembly time has been reduced by a factor of seven to one working day and the sense wire positioning accuracy improved by a factor of two to better than ten microns. Two sMDT chambers have been installed in ATLAS in 2014 to improve the momentum resolution in the barrel part of the spectrometer. The construction of an additional twelve chambers covering the feet regions of the ATLAS detector has started. It will be followed by the replacement of the MDT chambers at the ends of the barrel inner layer by sMDTs improving the Performance at the high expected background rates and providing space for additional RPC trigger chambers.
△ Less
Submitted 31 March, 2016;
originally announced March 2016.
-
Development of Fast High-Resolution Muon Drift-Tube Detectors for High Counting Rates
Authors:
B. Bittner,
J. Dubbert,
S. Horvat,
O. Kortner,
H. Kroha,
F. Legger,
R. Richter,
S. Adomeit,
O. Biebel,
A. Engl,
R. Hertenberger,
F. Rauscher,
A. Zibell
Abstract:
Pressurized drift-tube chambers are efficient detectors for high-precision tracking over large areas. The Monitored Drift-Tube (MDT) chambers of the muon spectrometer of the ATLAS detector at the Large Hadron Collider (LHC) reach a spatial resolution of 35 micons and almost 100% tracking efficiency with 6 layers of 30 mm diameter drift tubes operated with Ar:CO2 (93:7) gas mixture at 3 bar and a g…
▽ More
Pressurized drift-tube chambers are efficient detectors for high-precision tracking over large areas. The Monitored Drift-Tube (MDT) chambers of the muon spectrometer of the ATLAS detector at the Large Hadron Collider (LHC) reach a spatial resolution of 35 micons and almost 100% tracking efficiency with 6 layers of 30 mm diameter drift tubes operated with Ar:CO2 (93:7) gas mixture at 3 bar and a gas gain of 20000. The ATLAS MDT chambers are designed to cope with background counting rates due to neutrons and gamma-rays of up to about 300 kHz per tube which will be exceeded for LHC luminosities larger than the design value of 10-34 per square cm and second. Decreasing the drift-tube diameter to 15 mm while kee** the other parameters, including the gas gain, unchanged reduces the maximum drift time from about 700 ns to 200 ns and the drift-tube occupancy by a factor of 7. New drift-tube chambers for the endcap regions of the ATLAS muon spectrometer have been designed. A prototype chamber consisting of 12 times 8 layers of 15 mm diameter drift tubes of 1 m length has been constructed with a sense wire positioning accuracy of 20 microns. The 15 mm diameter drift-tubes have been tested with cosmic rays in the Gamma Irradiation Facility at CERN at counting rates of up to 1.85 MHz.
△ Less
Submitted 31 March, 2016;
originally announced March 2016.
-
Performance of Drift-Tube Detectors at High Counting Rates for High-Luminosity LHC Upgrades
Authors:
Bernhard Bittner,
Joerg Dubbert,
Oliver Kortner,
Hubert Kroha,
Alessandro Manfredini,
Sebastian Nowak,
Sebastian Ott,
Robert Richter,
Philipp Schwegler,
Daniele Zanzi,
Otmar Biebel,
Ralf Hertenberger,
Alexander Ruschke,
Andre Zibell
Abstract:
The performance of pressurized drift-tube detectors at very high background rates has been studied at the Gamma Irradiation Facility (GIF) at CERN and in an intense 20 MeV proton beam at the Munich Van-der-Graaf tandem accelerator for applications in large-area precision muon tracking at high-luminosity upgrades of the Large Hadron Collider (LHC). The ATLAS muon drifttube (MDT) chambers with 30 mm…
▽ More
The performance of pressurized drift-tube detectors at very high background rates has been studied at the Gamma Irradiation Facility (GIF) at CERN and in an intense 20 MeV proton beam at the Munich Van-der-Graaf tandem accelerator for applications in large-area precision muon tracking at high-luminosity upgrades of the Large Hadron Collider (LHC). The ATLAS muon drifttube (MDT) chambers with 30 mm tube diameter have been designed to cope with and neutron background hit rates of up to 500 Hz/square cm. Background rates of up to 14 kHz/square cm are expected at LHC upgrades. The test results with standard MDT readout electronics show that the reduction of the drift-tube diameter to 15 mm, while leaving the operating parameters unchanged, vastly increases the rate capability well beyond the requirements. The development of new small-diameter muon drift-tube (sMDT) chambers for LHC upgrades is completed. Further improvements of tracking efficiency and spatial resolution at high counting rates will be achieved with upgraded readout electronics employing improved signal sha** for high counting rates.
△ Less
Submitted 31 March, 2016;
originally announced March 2016.
-
Development of Muon Drift-Tube Detectors for High-Luminosity Upgrades of the Large Hadron Collider
Authors:
B. Bittner,
J. Dubbert,
O. Kortner,
H. Kroha,
F. Legger,
R. Richter,
O. Biebel,
A. Engl,
R. Hertenberger,
F. Rauscher
Abstract:
The muon detectors of the experiments at the Large Hadron Collider (LHC) have to cope with unprecedentedly high neutron and gamma ray background rates. In the forward regions of the muon spectrometer of the ATLAS detector, for instance, counting rates of 1.7 kHz/square cm are reached at the LHC design luminosity. For high-luminosity upgrades of the LHC, up to 10 times higher background rates are e…
▽ More
The muon detectors of the experiments at the Large Hadron Collider (LHC) have to cope with unprecedentedly high neutron and gamma ray background rates. In the forward regions of the muon spectrometer of the ATLAS detector, for instance, counting rates of 1.7 kHz/square cm are reached at the LHC design luminosity. For high-luminosity upgrades of the LHC, up to 10 times higher background rates are expected which require replacement of the muon chambers in the critical detector regions. Tests at the CERN Gamma Irradiation Facility showed that drift-tube detectors with 15 mm diameter aluminum tubes operated with Ar:CO2 (93:7) gas at 3 bar and a maximum drift time of about 200 ns provide efficient and high-resolution muon tracking up to the highest expected rates. For 15 mm tube diameter, space charge effects deteriorating the spatial resolution at high rates are strongly suppressed. The sense wires have to be positioned in the chamber with an accuracy of better than 50 ?micons in order to achieve the desired spatial resolution of a chamber of 50 ?microns up to the highest rates. We report about the design, construction and test of prototype detectors which fulfill these requirements.
△ Less
Submitted 31 March, 2016;
originally announced March 2016.
-
Performance of the new amplifier-shaper-discriminator chip for the ATLAS MDT chambers at the HL-LHC
Authors:
Hubert Kroha,
Sergey Abovyan,
Andrea Baschirotto,
Varuzhan Danielyan,
Markus Fras,
Felix Mueller,
Sebastian Nowak,
Federica Resta,
Marcello De Matteis,
Robert Richter,
Korbinian Schmidt-Sommerfeld,
Yazhou Zhao
Abstract:
The Phase-II Upgrade of the ATLAS Muon Detector requires new electronics for the readout of the MDT drift tubes. The first processing stage, the Amplifier-Shaper-Discriminator (ASD), determines the performance of the readout for crucial parameters like time resolution, gain uniformity, efficiency and noise rejection. An 8-channel ASD chip, using the IBM 130 nm CMOS 8RF-DM technology, has been desi…
▽ More
The Phase-II Upgrade of the ATLAS Muon Detector requires new electronics for the readout of the MDT drift tubes. The first processing stage, the Amplifier-Shaper-Discriminator (ASD), determines the performance of the readout for crucial parameters like time resolution, gain uniformity, efficiency and noise rejection. An 8-channel ASD chip, using the IBM 130 nm CMOS 8RF-DM technology, has been designed, produced and tested. The area of the chip is 2.2 x 2.9 square mm size. We present results of detailed measurements as well as a comparision with simulation results of the chip behaviour at three different levels of detail.
△ Less
Submitted 30 March, 2016;
originally announced March 2016.
-
Optimisation of the Read-out Electronics of Muon Drift-Tube Chambers for Very High Background Rates at HL-LHC and Future Colliders
Authors:
Sebastian Nowak,
Sergey Abovyan,
Philipp Gadow,
Katharina Ecker,
David Fink,
Markus Fras,
Oliver Kortner,
Hubert Kroha,
Felix Mueller,
Robert Richter,
Clemens Schmid,
Korbinian Schmidt-Sommerfeld,
Yazhou Zhao
Abstract:
In the ATLAS Muon Spectrometer, Monitored Drift Tube (MDT) chambers and sMDT chambers with half of the tube diameter of the MDTs are used for precision muon track reconstruction. The sMDT chambers are designed for operation at high counting rates due to neutron and gamma background irradiation expected for the HL-LHC and future hadron colliders. The existing MDT read-out electronics uses bipolar s…
▽ More
In the ATLAS Muon Spectrometer, Monitored Drift Tube (MDT) chambers and sMDT chambers with half of the tube diameter of the MDTs are used for precision muon track reconstruction. The sMDT chambers are designed for operation at high counting rates due to neutron and gamma background irradiation expected for the HL-LHC and future hadron colliders. The existing MDT read-out electronics uses bipolar signal sha** which causes an undershoot of opposite polarity and same charge after a signal pulse. At high counting rates and short electronics dead time used for the sMDTs, signal pulses pile up on the undershoot of preceding background pulses leading to a reduction of the signal amplitude and a jitter in the drift time measurement and, therefore, to a degradation of drift tube efficiency and spatial resolution. In order to further increase the rate capability of sMDT tubes, baseline restoration can be used in the read-out electronics to suppress the pile-up effects. A discrete bipolar sha** circuit with baseline restoration has been developed and used for reading out sMDT tubes under irradiation with a 24 MBq 90Sr source. The measurements results show a substantial improvement of the performance of the sMDT tubes at high counting rates.
△ Less
Submitted 29 March, 2016;
originally announced March 2016.
-
Precision Muon Tracking Detectors for High-Energy Hadron Colliders
Authors:
Philipp Gadow,
Oliver Kortner,
Hubert Kroha,
Robert Richter
Abstract:
Small-diameter muon drift tube (sMDT) chambers with 15 mm tube diameter are a cost-effective technology for high-precision muon tracking over large areas at high background rates as expected at future high-energy hadron colliders including HL-LHC. The chamber design and construction procedures have been optimized for mass production and provide sense wire positioning accuracy of better than 10 ?m.…
▽ More
Small-diameter muon drift tube (sMDT) chambers with 15 mm tube diameter are a cost-effective technology for high-precision muon tracking over large areas at high background rates as expected at future high-energy hadron colliders including HL-LHC. The chamber design and construction procedures have been optimized for mass production and provide sense wire positioning accuracy of better than 10 ?m. The rate capability of the sMDT chambers has been extensively tested at the CERN Gamma Irradiation Facility. It exceeds the one of the ATLAS muon drift tube (MDT) chambers, which are operated at unprecedentedly high background rates of neutrons and gamma-rays, by an order of magnitude, which is sufficient for almost the whole muon detector acceptance at FCC-hh at maximum luminosity. sMDT operational and construction experience exists from ATLAS muon spectrometer upgrades which are in progress or under preparation for LHC Phase 1 and 2.
△ Less
Submitted 29 March, 2016;
originally announced March 2016.
-
Construction and Test of New Precision Drift-Tube Chambers for the ATLAS Muon Spectrometer
Authors:
Hubert Kroha,
Oliver Kortner,
Korbinian Schmidt-Sommerfeld,
Eric Takasugi
Abstract:
ATLAS muon detector upgrades aim for increased acceptance for muon triggering and precision tracking and for improved rate capability of the muon chambers in the high-background regions of the detector with increasing LHC luminosity. The small-diameter Muon Drift Tube (sMDT) chambers have been developed for these purposes. With half of the drift-tube diameter of the MDT chambers and otherwise unch…
▽ More
ATLAS muon detector upgrades aim for increased acceptance for muon triggering and precision tracking and for improved rate capability of the muon chambers in the high-background regions of the detector with increasing LHC luminosity. The small-diameter Muon Drift Tube (sMDT) chambers have been developed for these purposes. With half of the drift-tube diameter of the MDT chambers and otherwise unchanged operating parameters, sMDT chambers share the advantages of the MDTs, but have an order of magnitude higher rate capability and can be installed in detector regions where MDT chambers do not fit in. The chamber assembly methods have been optimized for mass production, minimizing construction time and personnel. Sense wire positioning accuracies of 5 ?micons have been achieved in serial production for large-size chambers comprising several hundred drift tubes. The construction of new sMDT chambers for installation in the 2016/17 winter shutdown of the LHC and the design of sMDT chambers in combination with new RPC trigger chambers for replacement of the inner layer of the barrel muon spectrometer are in progress.
△ Less
Submitted 29 March, 2016;
originally announced March 2016.
-
Construction and Test of New Precision Drift-Tube Chambers for Upgrades of the ATLAS Muon Spectrometer in 2016/17
Authors:
H. Kroha,
O. Kortner,
F. Müller,
S. Nowak,
K. Schmidt-Sommerfeld
Abstract:
Small-diameter Muon Drift Tube (sMDT) chambers have been developed for the ATLAS muon detector upgrade. They possess an improved rate capability and a more compact design with respect to the existing chambers, which allows to equip detector regions uninstrument at present. The chamber assembly methods have been optimized for mass production, while the sense wire positioning accuracy is improved to…
▽ More
Small-diameter Muon Drift Tube (sMDT) chambers have been developed for the ATLAS muon detector upgrade. They possess an improved rate capability and a more compact design with respect to the existing chambers, which allows to equip detector regions uninstrument at present. The chamber assembly methods have been optimized for mass production, while the sense wire positioning accuracy is improved to below ten microns. The chambers will be ready for installation in the winter shutdown 2016/17 of the Large Hadron Collider. The design and construction of the new sMDT chambers for ATLAS will be discussed as well as measurements of their precision and performance.
△ Less
Submitted 7 December, 2015;
originally announced December 2015.
-
Performance of a First-Level Muon Trigger with High Momentum Resolution Based on the ATLAS MDT Chambers for HL-LHC
Authors:
P. Gadow,
O. Kortner,
S. Kortner,
H. Kroha,
F. Müller,
R. Richter
Abstract:
Highly selective first-level triggers are essential to exploit the full physics potential of the ATLAS experiment at High-Luminosity LHC (HL-LHC). The concept for a new muon trigger stage using the precision monitored drift tube (MDT) chambers to significantly improve the selectivity of the first-level muon trigger is presented. It is based on fast track reconstruction in all three layers of the e…
▽ More
Highly selective first-level triggers are essential to exploit the full physics potential of the ATLAS experiment at High-Luminosity LHC (HL-LHC). The concept for a new muon trigger stage using the precision monitored drift tube (MDT) chambers to significantly improve the selectivity of the first-level muon trigger is presented. It is based on fast track reconstruction in all three layers of the existing MDT chambers, made possible by an extension of the first-level trigger latency to six microseconds and a new MDT read-out electronics required for the higher overall trigger rates at the HL-LHC. Data from $pp$-collisions at $\sqrt{s} = 8\,\mathrm{TeV}$ is used to study the minimal muon transverse momentum resolution that can be obtained using the MDT precision chambers, and to estimate the resolution and efficiency of the MDT-based trigger. A resolution of better than $4.1\%$ is found in all sectors under study. With this resolution, a first-level trigger with a threshold of $18\,\mathrm{GeV}$ becomes fully efficient for muons with a transverse momentum above $24\,\mathrm{GeV}$ in the barrel, and above $20\,\mathrm{GeV}$ in the end-cap region.
△ Less
Submitted 30 November, 2015;
originally announced November 2015.
-
Precision Muon Tracking at Future Hadron Colliders with sMDT Chambers
Authors:
Oliver Kortner,
Hubert Kroha,
Felix Müller,
Sebastian Nowak,
Robert Richter
Abstract:
Small-diameter muon drift tube (sMDT) chambers are a cost-effective technology for high-precision muon tracking. The rate capability of the sMDT chambers has been extensively tested at the Gamma Irradiation Facility at CERN in view of expected rates at future high-energy hadron colliders. Results show that it fulfills the requirements over most of the acceptance of muon detectors. The optimization…
▽ More
Small-diameter muon drift tube (sMDT) chambers are a cost-effective technology for high-precision muon tracking. The rate capability of the sMDT chambers has been extensively tested at the Gamma Irradiation Facility at CERN in view of expected rates at future high-energy hadron colliders. Results show that it fulfills the requirements over most of the acceptance of muon detectors. The optimization of the read-out electronics to further increase the rate capability of the detectors is discussed. Chambers of this type are under construction for upgrades of the muon spectrometer of the ATLAS detector at high LHC luminosities. Design and construction procedures have been optimized for mass production while providing a precision of better than 10 micrometers in the sense wire positions and the mechanical stability required to cover large areas.
△ Less
Submitted 30 November, 2015;
originally announced November 2015.
-
Construction and test of high precision drift-tube (sMDT) chambers for the ATLAS muon spectrometer
Authors:
Sebastian Nowak,
Oliver Korner,
Hubert Kroha,
Philipp Schwegler,
Federico Sforza
Abstract:
For the upgrade of the ATLAS muon spectrometer in March 2014 new muon tracking chambers (sMDT) with drift-tubes of 15 mm diameter, half of the value of the standard ATLAS Monitored Drift-Tubes (MDT) chambers, and 10~$μ$m positioning accuracy of the sense wires have been constructed. The new chambers are designed to be fully compatible with the present ATLAS services but, with respect to the previo…
▽ More
For the upgrade of the ATLAS muon spectrometer in March 2014 new muon tracking chambers (sMDT) with drift-tubes of 15 mm diameter, half of the value of the standard ATLAS Monitored Drift-Tubes (MDT) chambers, and 10~$μ$m positioning accuracy of the sense wires have been constructed. The new chambers are designed to be fully compatible with the present ATLAS services but, with respect to the previously installed ATLAS MDT chambers, they are assembled in a more compact geometry and they deploy two additional tube layers that provide redundant rack information. The chambers are composed of 8 layers of in total 624 aluminium drift-tubes. The assembly of a chamber is completed within a week. A semi-automatized production line is used for the assembly of the drift-tubes prior to the chamber assembly. The production procedures and the quality control tests of the single components and of the complete chambers will be discussed. The wire position in the completed chambers have been measured by using a coordinate measuring machine.
△ Less
Submitted 1 July, 2014;
originally announced July 2014.
-
Upgrade of the ATLAS Muon Trigger for the SLHC
Authors:
Jörg Dubbert,
Sandra Horvat,
Oliver Kortner,
Hubert Kroha,
Robert Richter
Abstract:
The outer shell of the ATLAS experiment at the LHC consists of a system of toroidal air-core magnets in order to allow for the precise measurement of the transverse momentum p$_T$ of muons, which in many physics channels are a signature of interesting physics processes. For the precise determination of the muon momentum Monitored Drift Tube chambers (MDT) with high position accuracy are used, whil…
▽ More
The outer shell of the ATLAS experiment at the LHC consists of a system of toroidal air-core magnets in order to allow for the precise measurement of the transverse momentum p$_T$ of muons, which in many physics channels are a signature of interesting physics processes. For the precise determination of the muon momentum Monitored Drift Tube chambers (MDT) with high position accuracy are used, while for the fast identification of muon tracks chambers with high time resolution are used, able to select muons above a predefined p$_T$ threshold for use in the first Level of the ATLAS triggering system (Level-1 trigger). When the luminosity of the LHC will be upgraded to 4-5 times the present nominal value (SLHC) in about a decade from now, an improvement of the selectivity of the ATLAS Level-1 triggering system will be mandatory in order to cope with the maximum allowed trigger rate of 100 kHz. For the Level-1 trigger of the ATLAS muon spectrometer this means an increase of the p$_T$ threshold for single muons. Due to the limited spatial resolution of the trigger chambers, however, the selectivity for tracks above ~20 GeV/c is insufficient for an effective reduction of the Level-1 rate. We describe how the track coordinates measured in the MDT precision chambers can be used to decisively improve the selectivity for high momentum tracks. The resulting increase in latency will also be discussed.
△ Less
Submitted 31 October, 2010;
originally announced November 2010.
-
Expected Performance of the ATLAS Experiment - Detector, Trigger and Physics
Authors:
The ATLAS Collaboration,
G. Aad,
E. Abat,
B. Abbott,
J. Abdallah,
A. A. Abdelalim,
A. Abdesselam,
O. Abdinov,
B. Abi,
M. Abolins,
H. Abramowicz,
B. S. Acharya,
D. L. Adams,
T. N. Addy,
C. Adorisio,
P. Adragna,
T. Adye,
J. A. Aguilar-Saavedra,
M. Aharrouche,
S. P. Ahlen,
F. Ahles,
A. Ahmad,
H. Ahmed,
G. Aielli,
T. Akdogan
, et al. (2587 additional authors not shown)
Abstract:
A detailed study is presented of the expected performance of the ATLAS detector. The reconstruction of tracks, leptons, photons, missing energy and jets is investigated, together with the performance of b-tagging and the trigger. The physics potential for a variety of interesting physics processes, within the Standard Model and beyond, is examined. The study comprises a series of notes based on…
▽ More
A detailed study is presented of the expected performance of the ATLAS detector. The reconstruction of tracks, leptons, photons, missing energy and jets is investigated, together with the performance of b-tagging and the trigger. The physics potential for a variety of interesting physics processes, within the Standard Model and beyond, is examined. The study comprises a series of notes based on simulations of the detector and physics processes, with particular emphasis given to the data expected from the first years of operation of the LHC at CERN.
△ Less
Submitted 14 August, 2009; v1 submitted 28 December, 2008;
originally announced January 2009.
