Showing 1–16 of 16 results for author: Goetz, S

Hacking Encrypted Wireless Power: Cyber-Security of Dynamic Charging

Authors: Hui Wang, Nima Tashakor, Wei Jiang, Wei Liu, C. Q. Jiang, Stefan M. Goetz

Abstract: Recently, energy encryption for wireless power transfer has been developed for energy safety, which is important in public places to suppress unauthorized energy extraction. Most techniques vary the frequency so that unauthorized receivers cannot extract energy because of non-resonance. However, this strategy is unreliable. To stimulate the progress of energy encryption technology and point out se… ▽ More Recently, energy encryption for wireless power transfer has been developed for energy safety, which is important in public places to suppress unauthorized energy extraction. Most techniques vary the frequency so that unauthorized receivers cannot extract energy because of non-resonance. However, this strategy is unreliable. To stimulate the progress of energy encryption technology and point out security holes, this paper proposes a decryption method for the fundamental principle of encrypted frequency-varying wireless power transfer. The paper uses an auxiliary coil to detect the frequency and a switched-capacitor array to adaptively compensate the receiver for a wide frequency range. The switched-capacitor array contains two capacitors and one semi-conductor switch. One capacitor compensates the receiver all the time while the other's active time during one wireless power transfer cycle is regulated by the switch. Thus, the proposed hacking receiver controls the equivalent capacitance of the compensation and steals energy. Finally, a detailed simulation model and experimental results prove the effectiveness of the attack on frequency-hop** energy encryption. Although any nonnegligible energy extracted would be problematic, we achieved to steal 78% to 84% of the energy an authorized receiver could get. When the frequency changes, the interceptor is coarsely tuned very quickly, which can hack fast frequency-varying encrypted system. △ Less

Submitted 17 June, 2024; originally announced June 2024.

Comments: 10 pages, 17 figures

Hairpin Motors for Electromobility: Twists and Bends of a Technological Breakthrough that Initially Arrived A Century Too Soon

Authors: Stefan M. Goetz, Ricardo Lizana F., Sebastian Rivera

Abstract: There is currently a major trend to hairpin-winding motors for small and medium drives with increased power, specifically more torque density in the automotive industry. Practically all large players in the field either already use this winding technology or have announced doing so soon. However, hairpins, bar windings, and other segmented winding techniques are not purely a material and productio… ▽ More There is currently a major trend to hairpin-winding motors for small and medium drives with increased power, specifically more torque density in the automotive industry. Practically all large players in the field either already use this winding technology or have announced doing so soon. However, hairpins, bar windings, and other segmented winding techniques are not purely a material and production issue. Instead their application to small drives influences all aspects of the design of machines, which are currently explored and studied by the industry. These range from not obvious gaps in the theory, parameter studies for maxima of efficiency, possible as well as advantageous winding schemes, thermal design, and ways to control ac losses to specific materials and process difficulties. Despite the apparent novelty of the trend, however, designers could revisit a widely forgotten knowledge base of more than 100 years for many of those questions. This old knowledge base and the understanding that many recently presented concepts have been developed earlier may speed up the technological development and appear to be a key to further innovation. Instead, many problems need to be solved again and technologies re-invented. Furthermore, as this technology has recently become merely industry-driven, a substantial portion of the information and technological developments are not available to the public -- a state that to our eyes may harm the innovation capacity of the drives community. △ Less

Submitted 25 December, 2023; originally announced December 2023.

Comments: 22 pages, 20 figures

A Highly-Compact Direct-Injection Universal Power Flow and Quality Control Circuit

Authors: Mowei Lu, Mengjie Qin, Jan Kacetl, Eeshta Suresh, Teng Long, Stefan M. Goetz

Abstract: This paper presents a novel direct-injection modular universal power flow and quality control topology exclusively using lower power components. In addition to conventional high-voltage applications, it is particularly attractive for the distribution and secondary grids, e.g., in soft open points, down to low voltage as it can exploit the latest developments in low-voltage high-current semiconduct… ▽ More This paper presents a novel direct-injection modular universal power flow and quality control topology exclusively using lower power components. In addition to conventional high-voltage applications, it is particularly attractive for the distribution and secondary grids, e.g., in soft open points, down to low voltage as it can exploit the latest developments in low-voltage high-current semiconductors. In contrast to other concepts that do not interface the grid through transformers, it does not need to convert the entire line power but only the injected or extracted power difference. The proposed power flow and quality (f/q) controller comprises a shunt active front end, together with high-frequency links serving as a power supply for a series floating module per phase. Each of the floating modules is in series with one phase of the line, floating with the electric potential of that particular phase, avoiding any ground connection. Omitting bulky and dynamically limited line transformers of conventional universal power flow controllers, the presented direct-injection f/q controller enables exceptionally small size and volume, high power density, high frequency content, and fast response. In contrast to direct-injection concepts with full back-to-back converters, it only needs to handle a fraction of the power. The circuit combines grid-voltage low-current electronics in the shunt unit and low-voltage high-current modules in the floating series injection units. Simulations and experiments demonstrate and validate the concept. △ Less

Submitted 3 November, 2023; originally announced November 2023.

Design and Implementation of DC-to-5~MHz Wide-Bandwidth High-Power High-Fidelity Converter

Authors: **shui Zhang, Boshuo Wang, Xiaoyang Tian, Angel Peterchev, Stefan Goetz

Abstract: Advances in power electronics have made it possible to achieve high power levels, e.g., reaching GW in grids, or alternatively high output bandwidths, e.g., beyond MHz in communication. Achieving both simultaneously, however, remains challenging. Various applications, ranging from efficient multichannel wireless power transfer to cutting-edge medical and neuroscience applications, are demanding bo… ▽ More Advances in power electronics have made it possible to achieve high power levels, e.g., reaching GW in grids, or alternatively high output bandwidths, e.g., beyond MHz in communication. Achieving both simultaneously, however, remains challenging. Various applications, ranging from efficient multichannel wireless power transfer to cutting-edge medical and neuroscience applications, are demanding both high power and wide bandwidth. Conventional inverters can achieve high power and high quality at grid or specific frequency ranges but lose their fidelity when reaching higher output frequencies. Resonant circuits can promise a high output frequency but only a narrow bandwidth. We overcome the hardware challenges by combining gallium-nitride (GaN) transistors with modular cascaded double-H bridge circuits and control that can manage typical timing and balancing issues. We developed a lightweight embedded control solution that includes an improved look-up-table digital synthesizer and a novel adaptive-bias-elimination nearest-level modulation. This solution effectively solves the conflict between a high power level and high output bandwidth and can--in contrast to previous approaches--in principle be scaled in both dimensions. Our prototype exhibits a frequency range from DC to 5 MHz with <18% total voltage distortion across the entire frequency spectrum, while achieving a power level of >5 kW. We conducted tests by swee** the output frequency and two channel-mixing trials, which included a practical magnetogenetics-oriented stimulation pulse and an entertaining trial to reproduce the famous Arecibo message with the current spectrum. △ Less

Submitted 12 September, 2023; originally announced September 2023.

Comments: 8 pages, 11 figures

Topology, Analysis, and Modulation Strategy of a Fully Controlled Modular Battery Pack with Interconnected Output Ports

Authors: Nima Tashakor, Jan Kacetl, Davood Keshavarzi, Stefan Goetz

Abstract: Modular battery integrated converters or so called dynamically reconfigurable battery packs are expanding into emerging applications, including electromobility and grid storage. Although they offer many degrees of freedom, the state of the art focuses on single output systems and mostly neglects potential of such systems in generating multiple controlled outputs. This paper investigates the use of… ▽ More Modular battery integrated converters or so called dynamically reconfigurable battery packs are expanding into emerging applications, including electromobility and grid storage. Although they offer many degrees of freedom, the state of the art focuses on single output systems and mostly neglects potential of such systems in generating multiple controlled outputs. This paper investigates the use of the extra degrees of freedom that a reconfigurable battery offers to generate multiple outputs for the adjustable supply of various independent loads. The technology offers the potential for functional integration, exploiting already existing transistors, and for a reduction of separate dedicated power conversion stages. Interleaved output ports, where some modules are shared among different outputs, can further reduce the necessary power electronics and cost. However, using conventional modulation techniques in particular phase-shifted carrier modulation can be challenging with shared modules among multiple ports, and different control objectives can adversely impact the overall performance. Therefore, this paper proposes a strategy to decouple the control of multiple ports to enable further simplification of required power electronics. The proposed system does not require any additional active switches for the isolated port and can operate with a wide range of output voltages. Simulation and experiments verify the developed analysis. △ Less

Submitted 19 March, 2023; originally announced March 2023.

Voltage Estimation for Diode-Clamped MMC Using Compensated State-Space Model

Authors: N. Tashakor, Y. Zhang, S. Banana, F. Blaabjerg, S. Goetz

Abstract: Modular multilevel converters are wellknown in the energy sector and have significant potential in others, such as electromobility. Generally, their stable operation is at the expense of numerous sensors, communication burdens, and complicated balancing strategies that challenge their expansion to cost driven applications. Hence, the introduction of a sensorless voltage balancing strategy with a s… ▽ More Modular multilevel converters are wellknown in the energy sector and have significant potential in others, such as electromobility. Generally, their stable operation is at the expense of numerous sensors, communication burdens, and complicated balancing strategies that challenge their expansion to cost driven applications. Hence, the introduction of a sensorless voltage balancing strategy with a simple controller is an attractive objective. Diode clamped MMCs offer a simple yet effective solution by providing a unidirectional balancing path between two modules through a diode, and ideally, the modulation technique should compensate for the lack of bidirectional energy transfer. Hence open loop operation is possible. Although the open loop operation is desirable to reduce costs, good knowledge of the modules voltages for system monitoring and protection functions still appears mandatory. This paper develops a compensated state space model for diode clamped MMCs and integrates it with an optimal estimator to reliably estimate the voltage of all modules without any direct measurement at module terminals. Additionally, the model considers the effect of the diode clamped branches and their balancing effect, resulting in a 30 percent to 50 percent reduction in estimation error compared to the conventional model. △ Less

Submitted 3 March, 2023; originally announced March 2023.

A Smart Adaptively Reconfigurable DC Battery for Higher Efficiency of Electric Vehicle Drive Trains

Authors: Zhongxi Li, Aobo Yang, Gerry Chen, Nima Tashakor, Zhiyong Zeng, Angel V. Peterchev, Stefan M. Goetz

Abstract: This paper proposes a drive train topology with a dynamically reconfigurable dc battery, which breaks hard-wired batteries into smaller subunits. It can rapidly control the output voltage and even contribute to voltage sha** of the inverter. Based upon the rapid development of low-voltage transistors and modular circuit topologies in the recent years, the proposed technology uses recent 48 V pow… ▽ More This paper proposes a drive train topology with a dynamically reconfigurable dc battery, which breaks hard-wired batteries into smaller subunits. It can rapidly control the output voltage and even contribute to voltage sha** of the inverter. Based upon the rapid development of low-voltage transistors and modular circuit topologies in the recent years, the proposed technology uses recent 48 V power electronics to achieve higher-voltage output and reduce losses in electric vehicle (EV) drive trains. The fast switching capability and low loss of low-voltage field effect transistors (FET) allow sharing the modulation with the main drive inverter. As such, the slower insulated-gate bipolar transistors (IGBT) of the inverter can operate at ideal duty cycle and aggressively reduced switching, while the adaptive dc battery provides an adjustable voltage and all common-mode contributions at the dc link with lower loss. Up to 2/3 of the switching of the main inverter is avoided. At high drive speeds and thus large modulation indices, the proposed converter halves the total loss compared to using the inverter alone; at lower speeds and thus smaller modulation indices, the advantage is even more prominent because of the dynamically lowered dc-link voltage. Furthermore, it can substantially reduce the distortion, particularly at lower modulation indices, e.g., down to 1/2 compared to conventional space-vector modulation and even 1/3 for discontinuous pulse-width modulation with hard-wired battery. Other benefits include alleviated insulation stress for motor windings, active battery balancing, and eliminating the vulnerability of large hard-wired battery packs to weak cells. We demonstrate the proposed motor drive on a 3-kW setup with eight battery modules. △ Less

Submitted 18 January, 2023; originally announced January 2023.

Comments: 11 pages, 9 figures

Ageing Mitigation and Loss Control Through Ripple Management in Dynamically Reconfigurable Batteries

Authors: Tomas Kacetl, Jan Kacetl, Nima Tashakor, Stefan M. Goetz

Abstract: Dynamically reconfigurable batteries merge battery management with output formation in ac and dc batteries, increasing the available charge, power, and life time. However, the combined ripple generated by the load and the internal reconfiguration can degrade the battery. This paper introduces that the frequency range of the ripple matters for degradation and loss. It presents a novel control metho… ▽ More Dynamically reconfigurable batteries merge battery management with output formation in ac and dc batteries, increasing the available charge, power, and life time. However, the combined ripple generated by the load and the internal reconfiguration can degrade the battery. This paper introduces that the frequency range of the ripple matters for degradation and loss. It presents a novel control method that reduces the low-frequency ripple of dynamically reconfigurable battery technology to reduce cell ageing and loss. It furthermore shifts the residual ripple to higher frequencies where the lower impedance reduces heating and the dielectric capacitance of electrodes and electrolyte shunt the current around the electrochemical reactions. △ Less

Submitted 6 November, 2022; originally announced November 2022.

Comments: 8 pages, 8 figures

A Simplified Model for the Battery Ageing Potential Under Highly Rippled Load for Battery Management and Active Degradation Control

Authors: Tomas Kacetl, Jan Kacetl, Nima Tashakor, Stefan Goetz

Abstract: Whereas in typical standardized tests batteries are almost exclusively loaded with constant current or relatively slowly changing cycles, real applications involve rapid load ripple, which do not contribute to the net energy. The trend to reduced filter capacitors and even dynamically reconfigurable batteries further increases the ripple. The influence of rippled load on lithium batteries is there… ▽ More Whereas in typical standardized tests batteries are almost exclusively loaded with constant current or relatively slowly changing cycles, real applications involve rapid load ripple, which do not contribute to the net energy. The trend to reduced filter capacitors and even dynamically reconfigurable batteries further increases the ripple. The influence of rippled load on lithium batteries is therefore receiving increased attention. According to recent studies, accelerated ageing strongly depends on the frequency of the ripple. We use electrochemical models to derive a highly simplified regression model that catches the asymptotic behavior and allows parameter identification and calibration to specific cells. The model allows quantitative monitoring of the additional ageing due to ripple current in battery management systems. Furthermore it enables active control of the ageing potential by influencing the frequency content in modern battery systems, such as reconfigurable batteries. △ Less

Submitted 19 September, 2022; originally announced September 2022.

Comments: 7 pages

Dual-Port Dynamically Reconfigurable Battery with Semi-Controlled and Fully-Controlled Outputs

Authors: N. Tashakor, J. Kacetl, J. Fang, Z. Li, S. Goetz

Abstract: Modular multilevel converters (MMC) and cascaded H-bridge (CHB) converters are an established concept in ultra-high voltage systems. In combination with batteries, these circuits allow dynamically changing the series or parallel configuration of subportions of the battery as so-called modular battery integrated converters or reconfigurable batteries, and are being discussed for grid-storage and el… ▽ More Modular multilevel converters (MMC) and cascaded H-bridge (CHB) converters are an established concept in ultra-high voltage systems. In combination with batteries, these circuits allow dynamically changing the series or parallel configuration of subportions of the battery as so-called modular battery integrated converters or reconfigurable batteries, and are being discussed for grid-storage and electromobility applications. A large body of research focuses on such circuits for supplying a single load, such as a motor for electric drives. Modularity, failure tolerance, less dependence on the weakest element of a battery pack, higher controllability, and better efficiency are the main incentives behind this pursuit. However, most studies neglect the auxiliary loads which require isolation from the high-voltage battery. This paper proposes a simple topology and controller that can fork off a second (galvanically isolated) output of a reconfigurable dc battery. The proposed system provides a nonisolated semicontrolled port for the dc link to maintain the operating point of the main inverter(s) close to optimal, while fully controlling an isolated output for the auxiliaries per the safety regulations. The proposed system does not require additional active switches for the auxiliary port and can operate with a wide range of voltages. Simulation and experiments verify the developed analysis. △ Less

Submitted 3 June, 2022; originally announced June 2022.

Comments: All Rights reserved. This work has been submitted for publication. Copyright may be transferred without notice, after which this version may no longer be accessible

Synchronous Multistep Predictive Spectral Control of the Switching Distortion in DC--DC Converters

Authors: Christian Korte, Till Luetje, Stefan M. Goetz

Abstract: In automotive power electronics, distortion and electromagnetic interference (EMI) generated by the switching action of power semiconductors can be a significant challenge for the design of a compact, lightweight vehicle. As semiconductor switching frequencies increase, e.g., through the introduction of new materials, such as gallium nitride and silicon carbide, this problem becomes more severe. W… ▽ More In automotive power electronics, distortion and electromagnetic interference (EMI) generated by the switching action of power semiconductors can be a significant challenge for the design of a compact, lightweight vehicle. As semiconductor switching frequencies increase, e.g., through the introduction of new materials, such as gallium nitride and silicon carbide, this problem becomes more severe. We present a control scheme for an automotive dc-to-dc converter that reduces the EMI generated by sha** switching distortion predictively at the run time. The multistep model-predictive control scheme chooses the subsequent switching state that optimizes the output spectrum according to predefined criteria. To achieve real-time operation, it evaluates the possible switching state candidates for the next modulation step without explicitly solving a single Fourier transform. In addition, the switching rate and voltage ripple are controlled in a single unified control law. We present and experimentally validate that the control scheme can indeed run at real time already with currently available mid-range hardware. The results demonstrate that the largest spectral peak of the switching distortion can be decreased by 48 dB compared to conventional pulse-width modulation. Furthermore, spectral gaps can be implemented in the output distortion and altered in real-time, allowing certain frequency bands -- e.g., bands used by other sensitive electronics such as sensors, communication busses, or tuners -- to be kept free of EMI from the converter's switching actions. △ Less

Submitted 30 April, 2022; originally announced May 2022.

Comments: 10 pages, 14 figures

Comparison study of the combination of the SPSA algorithm and the PSO algorithm

Authors: Bertrand Ngansop, Stefan Götz, Martin Eckl

Abstract: Particle swarm optimization (PSO) is attracting an ever-growing attention and more than ever it has found many application areas for many challenging optimization problems. It is, however, a known fact that PSO has a severe drawback in the update of its global best (gbest) particle, which has a crucial role of guiding the rest of the swarm. In this paper, we propose three efficient solutions to re… ▽ More Particle swarm optimization (PSO) is attracting an ever-growing attention and more than ever it has found many application areas for many challenging optimization problems. It is, however, a known fact that PSO has a severe drawback in the update of its global best (gbest) particle, which has a crucial role of guiding the rest of the swarm. In this paper, we propose three efficient solutions to remedy this problem using the SPSA Algorithm. In the first approach, gbest is updated with respect to a global estimation of the gradient and can avoid getting trapped into a local optimum. The second approach is based on the formation of an alternative or artificial global best particle, the so-called aGB, which can replace the native gbest particle for a better guidance, the decision of which is held by a fair competition between the two. The third approach is based on the update of the swarm particle. For this purpose we use simultaneous perturbation stochastic approximation (SPSA) for its low cost. Since SPSA is applied only to the gbest (not to the entire swarm) or to the entire swarm, both approaches result thus in a negligible overhead cost for the entire PSO process. Both approaches are shown to significantly improve the performance of PSO over a wide range of non-linear functions, especially if SPSA and PSO parameters are well selected to fit the problem at hand. As in the basic PSO application, experimental results show that the proposed approaches significantly improved the quality of the Optimization process as measured by a statistic analysis. △ Less

Submitted 25 April, 2022; originally announced April 2022.

A Generalized Switched-Capacitor Modular Multilevel Inverter Topology for Multiphase Electrical Machines with Capacitor-Voltage Self-Balancing Capability

Authors: Farzad Iraji, Nima Tashakor, Stefan Goetz

Abstract: Recent research on multilevel inverters shows exciting properties, including the potential to generate multiple output voltages and integrated voltage boosting. However, most presented inverter topologies have a restricted number of output voltage levels and limited output voltage boosting ratio. In addition, balancing the voltage of capacitors in multilevel converters is very important and should… ▽ More Recent research on multilevel inverters shows exciting properties, including the potential to generate multiple output voltages and integrated voltage boosting. However, most presented inverter topologies have a restricted number of output voltage levels and limited output voltage boosting ratio. In addition, balancing the voltage of capacitors in multilevel converters is very important and should be considered in the topology or control method. This paper describes a generalized switched-capacitor circuit topology for multilevel dc-to-ac inverters that can be developed for the desired output voltage levels. Also, the maximum ac output voltage can vary from values much lower than the dc input voltage to several times of it depending on the design requirement. High-voltage dc input and ac output could be handled using low-voltage capacitors, which substantially decreases overall cost and volume. The proposed topology further allows for easy expansion through stackable circuits for multiple load phases. It has an inherent capacity for balancing the voltage of capacitors. To validate the feasibility and practicality of this concept, we provide circuit descriptions, control strategies, design recommendations, and pertinent simulation findings for the suggested inverter topology. △ Less

Submitted 14 April, 2022; originally announced April 2022.

Degradation-Reducing Control for Dynamically Reconfigurable Batteries

Authors: Tomas Kacetl, Jan Kacetl, **yang Fang, Malte Jaensch, Stefan Goetz

Abstract: Cascaded circuits such as modular multilevel con-verters (MMC) offer attractive qualities in reconfigurable battery applications. In contrast to conventional hard-wired dc battery packs, the MMC topology loads modules with ac current, which may lead to additional ageing of batteries. As recent studies reveal, such ageing of batteries occurs at low-frequency load ripple, and almost vanishes at high… ▽ More Cascaded circuits such as modular multilevel con-verters (MMC) offer attractive qualities in reconfigurable battery applications. In contrast to conventional hard-wired dc battery packs, the MMC topology loads modules with ac current, which may lead to additional ageing of batteries. As recent studies reveal, such ageing of batteries occurs at low-frequency load ripple, and almost vanishes at high frequencies. State of the art in MMC bat-tery control focuses on state of charge and temperature balancing of individual modules. Previous methods to suppress ripple rely on slow feedback loops and low dynamics, which tends to form low-frequency patterns in the module load that negatively contribute to their ageing. This paper presents a novel module-current-oriented high-bandwidth control technique which minimizes low-frequency components in the module load spectrum. The control method respects limitations related to module data acquisition and enhanc-es the feedback bandwidth using observation techniques. We verify the proposed method experimentally on a laboratory setup and estimate the influence on the battery cells. △ Less

Submitted 23 February, 2022; originally announced February 2022.

Comments: 9 pages, 11 figures

Solid-State Inrush Current Limiter Controller Based on Inrush Prediction for Large Transformers

Authors: Nima Tashakor, Teymoor Ghanbari, Ebrahim Farjah, Ehsan Bagheri, Stefan Goetz

Abstract: Inrush current problems of the industrial transformers are occasionally more serious than the utility transformers. A new Solid-State Inrush Current Limiter (SSICL) is proposed for medium voltage power transformers. The SSICL consists of three similar sets. Each set includes a bidirectional semiconductor switch and an inrush current limiter resistor. Using a control strategy based on Kalman filter… ▽ More Inrush current problems of the industrial transformers are occasionally more serious than the utility transformers. A new Solid-State Inrush Current Limiter (SSICL) is proposed for medium voltage power transformers. The SSICL consists of three similar sets. Each set includes a bidirectional semiconductor switch and an inrush current limiter resistor. Using a control strategy based on Kalman filtering, transformer inrush current is suppressed during magnetization process. In fact, built up profile of the inrush current is dictated in accordance with the estimated current by a slow dynamic Kalman filter. A single-phase prototype SSICL is developed and tested. The proposed control scheme is simulated in MATLAB-SIMULINK. By using Real Time (RT) toolbox of the MATLAB software and a PCI_1711U, interrelationship between the SSICL and its controlling system is realized. Some experiments are carried out to evaluate the performance of the SSICL. The results show that the proposed SSICL can considerably suppress inrush current of the transformer △ Less

Submitted 27 September, 2020; originally announced September 2020.

Modular Multilevel Converter with Sensorless Diode-Clamped Balancing through Level-Adjusted Phase-Shifted Modulation

Authors: N. Tashakor, M. Kilictas, E. Bagheri, S. Goetz

Abstract: Cascaded H-bridge and modular multilevel converters (MMC) are on the rise with emerging applications in renewable energy generation, energy storage, and electric motor drives. However, their well-known advantages come at the price of complicated balancing, high-bandwidth isolated monitoring, and numerous sensors that can prevent MMCs from expanding into highly cost driven markets. Therefore, an ob… ▽ More Cascaded H-bridge and modular multilevel converters (MMC) are on the rise with emerging applications in renewable energy generation, energy storage, and electric motor drives. However, their well-known advantages come at the price of complicated balancing, high-bandwidth isolated monitoring, and numerous sensors that can prevent MMCs from expanding into highly cost driven markets. Therefore, an obvious trend in research is develo** control and topologies that depend less on measurements and benefit from simpler control. Diode-clamped topologies are considered among the more applicable solutions. The main problem with a diode-clamped topology is that it can only balance the module voltages of a string in one direction; therefore, it cannot provide a completely balanced operation. This paper proposes an effective balancing technique for the diode-clamped topology. The proposed solution exploits the dc component of the arm current by introducing a symmetrically level-adjusted phase-shifted modulation scheme, and ensures the balancing current flow is always in the correct direction. The main advantages of this method are sensorless operation, no added computation and control effort, and low overall cost. Analysis and detailed simulations provide insight into the operation of the system as well as the new balancing technique and the experimental results confirm the provided discussions. △ Less

Submitted 23 September, 2020; originally announced September 2020.

Journal ref: IEEE Transactions on Power Electronics ( Volume: 36, Issue: 7, July 2021)