-
Optimal Multi-Robot Communication-Aware Trajectory Planning by Constraining the Fiedler Value
Authors:
Jeppe Heini Mikkelsen,
Roberto Galeazzi,
Matteo Fumagalli
Abstract:
The paper present a novel approach for the solution of the Multi-Robot Communication-Aware Trajectory Planning, which builds on a general optimisation framework where the changes in robots positions are used as decision variable, and linear constraints on the trajectories of the robots are introduced to ensure communication performance and collision avoidance. The Fiedler value is adopted as commu…
▽ More
The paper present a novel approach for the solution of the Multi-Robot Communication-Aware Trajectory Planning, which builds on a general optimisation framework where the changes in robots positions are used as decision variable, and linear constraints on the trajectories of the robots are introduced to ensure communication performance and collision avoidance. The Fiedler value is adopted as communication performance metric. The validity of the method in computing both feasible and optimal trajectories for the robots is demonstrated both in simulation and experimentally. Results show that the constraint on the Fiedler value ensures that the robot network fulfils its objective while maintaining communication connectivity at all times. Further, the paper shows that the introduction of approximations for the constraints enables a significant improvement in the computational time of the solution, which remain very close to the optimal solution.
△ Less
Submitted 26 June, 2024;
originally announced June 2024.
-
Multi-Wheeled Passive Sliding with Fully-Actuated Aerial Robots: Tip-Over Recovery and Avoidance
Authors:
Tong Hui,
Eugenio Cuniato,
Michael Pantic,
Jefferson Ghielmini,
Christian Lanegger,
Dimitrios Papageorgiou,
Marco Tognon,
Roland Siegwart,
Matteo Fumagalli
Abstract:
Push-and-slide tasks carried out by fully-actuated aerial robots can be used for inspection and simple maintenance tasks at height, such as non-destructive testing and painting. Often, an end-effector based on multiple non-actuated contact wheels is used to contact the surface. This approach entails challenges in ensuring consistent wheel contact with a surface whose exact orientation and location…
▽ More
Push-and-slide tasks carried out by fully-actuated aerial robots can be used for inspection and simple maintenance tasks at height, such as non-destructive testing and painting. Often, an end-effector based on multiple non-actuated contact wheels is used to contact the surface. This approach entails challenges in ensuring consistent wheel contact with a surface whose exact orientation and location might be uncertain due to sensor aliasing and drift. Using a standard full-pose controller dependent on the inaccurate surface position and orientation may cause wheels to lose contact during sliding, and subsequently lead to robot tip-over. To address the tip-over issue, we present two approaches: (1) tip-over avoidance guidelines for hardware design, and (2) control for tip-over recovery and avoidance. Physical experiments with a fully-actuated aerial vehicle were executed for a push-and-slide task on a flat surface. The resulting data is used in deriving tip-over avoidance guidelines and designing a simulator that closely captures real-world conditions. We then use the simulator to test the effectiveness and robustness of the proposed approaches in risky scenarios against uncertainties.
△ Less
Submitted 28 May, 2024; v1 submitted 28 May, 2024;
originally announced May 2024.
-
A Center-of-Mass Shifting Aerial Manipulation Platform for Heavy-Tool Handling on Non-Horizontal Surfaces
Authors:
Tong Hui,
Stefan Rucareanu,
Haotian Liu,
Matteo Fumagalli
Abstract:
Aerial vehicles equipped with manipulators can serve contact-based industrial applications, where fundamental tasks like drilling and grinding often necessitate aerial platforms to handle heavy tools. Industrial environments often involve non-horizontal surfaces. Existing aerial manipulation platforms based on multirotors typically feature a fixed CoM (Center of Mass) within the rotor-defined area…
▽ More
Aerial vehicles equipped with manipulators can serve contact-based industrial applications, where fundamental tasks like drilling and grinding often necessitate aerial platforms to handle heavy tools. Industrial environments often involve non-horizontal surfaces. Existing aerial manipulation platforms based on multirotors typically feature a fixed CoM (Center of Mass) within the rotor-defined area, leading to a considerable moment arm between the EE (End-Effector) tip and the CoM for operations on such surfaces. Carrying heavy tools at the EE tip of the manipulator with an extended moment arm can lead to system instability and potential damage to the servo actuators used in the manipulator. To tackle this issue, we present a novel aerial vehicle tailored for handling heavy tools on non-horizontal surfaces. In this work, we provide the platform's system design, modeling, and control strategies. This platform can carry heavy manipulators within the rotor-defined area during free flight. During interactions, the manipulator can shift towards the work surface outside the rotor-defined area, resulting in a displaced CoM location with a significantly shorter moment arm. Furthermore, we propose a method for automatically determining the manipulator's position to reach the maximum CoM displacement towards the work surface. Our proposed concepts are validated through simulations that closely capture the developed physical prototype of the platform.
△ Less
Submitted 1 April, 2024;
originally announced April 2024.
-
Passive Aligning Physical Interaction of Fully-Actuated Aerial Vehicles for Pushing Tasks
Authors:
Tong Hui,
Eugenio Cuniato,
Michael Pantic,
Marco Tognon,
Matteo Fumagalli,
Roland Siegwart
Abstract:
Recently, the utilization of aerial manipulators for performing pushing tasks in non-destructive testing (NDT) applications has seen significant growth. Such operations entail physical interactions between the aerial robotic system and the environment. End-effectors with multiple contact points are often used for placing NDT sensors in contact with a surface to be inspected. Aligning the NDT senso…
▽ More
Recently, the utilization of aerial manipulators for performing pushing tasks in non-destructive testing (NDT) applications has seen significant growth. Such operations entail physical interactions between the aerial robotic system and the environment. End-effectors with multiple contact points are often used for placing NDT sensors in contact with a surface to be inspected. Aligning the NDT sensor and the work surface while preserving contact, requires that all available contact points at the end-effector tip are in contact with the work surface. With a standard full-pose controller, attitude errors often occur due to perturbations caused by modeling uncertainties, sensor noise, and environmental uncertainties. Even small attitude errors can cause a loss of contact points between the end-effector tip and the work surface. To preserve full alignment amidst these uncertainties, we propose a control strategy which selectively deactivates angular motion control and enables direct force control in specific directions. In particular, we derive two essential conditions to be met, such that the robot can passively align with flat work surfaces achieving full alignment through the rotation along non-actively controlled axes. Additionally, these conditions serve as hardware design and control guidelines for effectively integrating the proposed control method for practical usage. Real world experiments are conducted to validate both the control design and the guidelines.
△ Less
Submitted 27 February, 2024;
originally announced February 2024.
-
Safety-Conscious Pushing on Diverse Oriented Surfaces with Underactuated Aerial Vehicles
Authors:
Tong Hui,
Manuel J. Fernandez Gonzalez,
Matteo Fumagalli
Abstract:
Pushing tasks performed by aerial manipulators can be used for contact-based industrial inspections. Underactuated aerial vehicles are widely employed in aerial manipulation due to their widespread availability and relatively low cost. Industrial infrastructures often consist of diverse oriented work surfaces. When interacting with such surfaces, the coupled gravity compensation and interaction fo…
▽ More
Pushing tasks performed by aerial manipulators can be used for contact-based industrial inspections. Underactuated aerial vehicles are widely employed in aerial manipulation due to their widespread availability and relatively low cost. Industrial infrastructures often consist of diverse oriented work surfaces. When interacting with such surfaces, the coupled gravity compensation and interaction force generation of underactuated aerial vehicles can present the potential challenge of near-saturation operations. The blind utilization of these platforms for such tasks can lead to instability and accidents, creating unsafe operating conditions and potentially damaging the platform. In order to ensure safe pushing on these surfaces while managing platform saturation, this work establishes a safety assessment process. This process involves the prediction of the saturation level of each actuator during pushing across variable surface orientations. Furthermore, the assessment results are used to plan and execute physical experiments, ensuring safe operations and preventing platform damage.
△ Less
Submitted 23 February, 2024;
originally announced February 2024.
-
Versatile Airborne Ultrasonic NDT Technologies via Active Omni-Sliding with Over-Actuated Aerial Vehicles
Authors:
Tong Hui,
Florian Braun,
Nicolas Scheidt,
Marius Fehr,
Matteo Fumagalli
Abstract:
This paper presents the utilization of advanced methodologies in aerial manipulation to address meaningful industrial applications and develop versatile ultrasonic Non-Destructive Testing (NDT) technologies with aerial robots. The primary objectives of this work are to enable multi-point measurements through sliding without re-approaching the work surface, and facilitate the representation of mate…
▽ More
This paper presents the utilization of advanced methodologies in aerial manipulation to address meaningful industrial applications and develop versatile ultrasonic Non-Destructive Testing (NDT) technologies with aerial robots. The primary objectives of this work are to enable multi-point measurements through sliding without re-approaching the work surface, and facilitate the representation of material thickness with B and C scans via dynamic scanning in arbitrary directions (i.e. omnidirections). To accomplish these objectives, a payload that can slide in omnidirections (here we call the omni-sliding payload) is designed for an over-actuated aerial vehicle, ensuring truly omnidirectional sliding mobility while exerting consistent forces in contact with a flat work surface. The omni-sliding payload is equipped with an omniwheel-based active end-effector and an Electro Magnetic Acoustic Transducer (EMAT). Furthermore, to ensure successful development of the designed payload and integration with the aerial vehicle, a comprehensive studying on contact conditions and system dynamics during active sliding is presented, and the derived system constraints are later used as guidelines for the hardware development and control setting. The proposed methods are validated through experiments, encompassing both the wall-sliding task and dynamic scanning for Ultrasonic Testing (UT), employing the aerial platform - Voliro T.
△ Less
Submitted 8 November, 2023;
originally announced November 2023.
-
Distributed Planning for Rigid Robot Formations using Consensus on the Transformation of a Base Configuration
Authors:
Jeppe Heini Mikkelsen,
Matteo Fumagalli
Abstract:
This paper presents a novel planning method that achieves navigation of multi-robot formations in cluttered environments, while maintaining the formation throughout the robots motion. The method utilises a decentralised approach to find feasible formation parameters that guarantees formation constraints for rigid formations. The method proves to be computationally efficient, making it relevant for…
▽ More
This paper presents a novel planning method that achieves navigation of multi-robot formations in cluttered environments, while maintaining the formation throughout the robots motion. The method utilises a decentralised approach to find feasible formation parameters that guarantees formation constraints for rigid formations. The method proves to be computationally efficient, making it relevant for reactive planning and control of multi-robot systems formation. The method has been tested in a simulation environment to prove feasibility and run-time efficiency.
△ Less
Submitted 14 July, 2023;
originally announced July 2023.