-
Indoor 5G 3GPP-like Channel Models for Office and Shop** Mall Environments
Authors:
Katsuyuki Haneda,
Lei Tian,
Henrik Asplund,
Jian Li,
Yi Wang,
David Steer,
Clara Li,
Tommaso Balercia,
Sunguk Lee,
YoungSuk Kim,
Amitava Ghosh,
Timothy Thomas,
Takehiro Nakamura,
Yuichi Kakishima,
Tetsuro Imai,
Haralabos Papadopoulas,
Theodore S. Rappaport,
George R. MacCartney Jr.,
Mathew K. Samimi,
Shu Sun,
Ozge Koymen,
Sooyoung Hur,
Jeongho Park,
Charlie Zhang,
Evangelos Mellios
, et al. (3 additional authors not shown)
Abstract:
Future mobile communications systems are likely to be very different to those of today with new service innovations driven by increasing data traffic demand, increasing processing power of smart devices and new innovative applications. To meet these service demands the telecommunications industry is converging on a common set of 5G requirements which includes network speeds as high as 10 Gbps, cel…
▽ More
Future mobile communications systems are likely to be very different to those of today with new service innovations driven by increasing data traffic demand, increasing processing power of smart devices and new innovative applications. To meet these service demands the telecommunications industry is converging on a common set of 5G requirements which includes network speeds as high as 10 Gbps, cell edge rate greater than 100 Mbps, and latency of less than 1 msec. To reach these 5G requirements the industry is looking at new spectrum bands in the range up to 100 GHz where there is spectrum availability for wide bandwidth channels. For the development of new 5G systems to operate in bands up to 100 GHz there is a need for accurate radio propagation models which are not addressed by existing channel models developed for bands below 6 GHz. This paper presents a preliminary overview of the 5G channel models for bands up to 100 GHz in indoor offices and shop** malls, derived from extensive measurements across a multitude of bands. These studies have found some extensibility of the existing 3GPP models to the higher frequency bands up to 100 GHz. The measurements indicate that the smaller wavelengths introduce an increased sensitivity of the propagation models to the scale of the environment and show some frequency dependence of the path loss as well as increased occurrence of blockage. Further, the penetration loss is highly dependent on the material and tends to increase with frequency. The small-scale characteristics of the channel such as delay spread and angular spread and the multipath richness is somewhat similar over the frequency range, which is encouraging for extending the existing 3GPP models to the wider frequency range. Further work will be carried out to complete these models, but this paper presents the first steps for an initial basis for the model development.
△ Less
Submitted 13 March, 2016;
originally announced March 2016.
-
5G 3GPP-like Channel Models for Outdoor Urban Microcellular and Macrocellular Environments
Authors:
Katsuyuki Haneda,
Lei Tian,
Yi Zheng,
Henrik Asplund,
Jian Li,
Yi Wang,
David Steer,
Clara Li,
Tommaso Balercia,
Sunguk Lee,
YoungSuk Kim,
Amitava Ghosh,
Timothy Thomas,
Takehiro Nakamura,
Yuichi Kakishima,
Tetsuro Imai,
Haralabos Papadopoulas,
Theodore S. Rappaport,
George R. MacCartney Jr.,
Mathew K. Samimi,
Shu Sun,
Ozge Koymen,
Sooyoung Hur,
Jeongho Park,
Charlie Zhang
, et al. (4 additional authors not shown)
Abstract:
For the development of new 5G systems to operate in bands up to 100 GHz, there is a need for accurate radio propagation models at these bands that currently are not addressed by existing channel models developed for bands below 6 GHz. This document presents a preliminary overview of 5G channel models for bands up to 100 GHz. These have been derived based on extensive measurement and ray tracing re…
▽ More
For the development of new 5G systems to operate in bands up to 100 GHz, there is a need for accurate radio propagation models at these bands that currently are not addressed by existing channel models developed for bands below 6 GHz. This document presents a preliminary overview of 5G channel models for bands up to 100 GHz. These have been derived based on extensive measurement and ray tracing results across a multitude of frequencies from 6 GHz to 100 GHz, and this document describes an initial 3D channel model which includes: 1) typical deployment scenarios for urban microcells (UMi) and urban macrocells (UMa), and 2) a baseline model for incorporating path loss, shadow fading, line of sight probability, penetration and blockage models for the typical scenarios. Various processing methodologies such as clustering and antenna decoupling algorithms are also presented.
△ Less
Submitted 25 February, 2016; v1 submitted 24 February, 2016;
originally announced February 2016.
-
Synthesizing Omnidirectional Antenna Patterns, Received Power and Path Loss from Directional Antennas for 5G Millimeter-Wave Communications
Authors:
Shu Sun,
George R. MacCartney Jr.,
Mathew K. Samimi,
Theodore S. Rappaport
Abstract:
Omnidirectional path loss models are vital for radiosystem design in wireless communication systems, as they allow engineers to perform network simulations for systems with arbitrary antenna patterns. At millimeter-wave frequencies, channel measurements are frequently conducted using steerable highgain directional antennas at both the transmitter and receiver to make up for the significant increas…
▽ More
Omnidirectional path loss models are vital for radiosystem design in wireless communication systems, as they allow engineers to perform network simulations for systems with arbitrary antenna patterns. At millimeter-wave frequencies, channel measurements are frequently conducted using steerable highgain directional antennas at both the transmitter and receiver to make up for the significant increase in free space path loss at these frequencies compared to traditional cellular systems that operate at lower frequencies. The omnidirectional antenna pattern, and resulting omnidirectional received power must therefore be synthesized from many unique pointing angles, where the transmit and receive antennas are rotated over many different azimuth and elevation planes. In this paper, the equivalent omnidirectional antenna pattern and omnidirectional received power are synthesized by summing the received powers from all measured unique pointing angles obtained at antenna halfpower beamwidth step increments in the azimuth and elevation planes, and this method is validated by demonstrating that the synthesized omnidirectional received power and path loss are independent of antenna beamwidth, through theoretical analyses and millimeter-wave propagation measurements using antennas with different beamwidths. The method in this paper is shown to provide accurate results while enhancing the measurement range substantially through the use of directional antennas.
△ Less
Submitted 1 December, 2015; v1 submitted 23 November, 2015;
originally announced November 2015.
-
Local Multipath Model Parameters for Generating 5G Millimeter-Wave 3GPP-like Channel Impulse Response
Authors:
Mathew K. Samimi,
Theodore S. Rappaport
Abstract:
This paper presents 28 GHz and 73 GHz empirically-derived large-scale and small-scale channel model parameters that characterize average temporal and angular properties of multipaths. Omnidirectional azimuth scans at both the transmitter and receiver used high gain directional antennas, from which global 3GPP modeling parameters for the mean global azimuth and zenith spreads of arrival were found…
▽ More
This paper presents 28 GHz and 73 GHz empirically-derived large-scale and small-scale channel model parameters that characterize average temporal and angular properties of multipaths. Omnidirectional azimuth scans at both the transmitter and receiver used high gain directional antennas, from which global 3GPP modeling parameters for the mean global azimuth and zenith spreads of arrival were found to be 22 degrees and 6.2 degrees at 28 GHz, and 37.1 degrees and 3.8 degrees at 73 GHz, respectively, in non-line of sight (NLOS). Small-scale spatial measurements at 28 GHz reveal a mean cross-polar ratio for individual multipath components of 29.7 dB and 16.7 dB in line of sight and NLOS, respectively. Small-scale parameters extracted using the KPowerMeans algorithm yielded on average 5.3 and 4.6 clusters at 28 GHz and 73 GHz, respectively, in NLOS. The time cluster - spatial lobe (TCSL) modeling approach uses an alternative physically-based binning procedure and recreates 3GPP model parameters to generate channel impulse responses, as well as new parameters like the RMS lobe angular spreads useful in quantifying millimeter-wave directionality. The TCSL algorithm faithfully reproduces first- and second-order statistics of measured millimeter-wave channels.
△ Less
Submitted 15 February, 2016; v1 submitted 21 November, 2015;
originally announced November 2015.
-
MIMO Channel Modeling and Capacity Analysis for 5G Millimeter-Wave Wireless Systems
Authors:
Mathew K. Samimi,
Shu Sun,
Theodore S. Rappaport
Abstract:
This paper presents a 3-D statistical channel model of the impulse response with small-scale spatially correlated random coefficients for multi-element transmitter and receiver antenna arrays, derived using the physically-based time cluster - spatial lobe (TCSL) clustering scheme. The small-scale properties of multipath amplitudes are modeled based on 28 GHz outdoor millimeter-wave small-scale loc…
▽ More
This paper presents a 3-D statistical channel model of the impulse response with small-scale spatially correlated random coefficients for multi-element transmitter and receiver antenna arrays, derived using the physically-based time cluster - spatial lobe (TCSL) clustering scheme. The small-scale properties of multipath amplitudes are modeled based on 28 GHz outdoor millimeter-wave small-scale local area channel measurements. The wideband channel capacity is evaluated by considering measurement-based Rician-distributed voltage amplitudes, and the spatial autocorrelation of multipath amplitudes for each pair of transmitter and receiver antenna elements. Results indicate that Rician channels may exhibit equal or possibly greater capacity compared to Rayleigh channels, depending on the number of antennas.
△ Less
Submitted 27 January, 2016; v1 submitted 21 November, 2015;
originally announced November 2015.
-
28 GHz Millimeter-Wave Ultrawideband Small-Scale Fading Models in Wireless Channels
Authors:
Mathew K. Samimi,
George R. MacCartney, Jr.,
Shu Sun,
Theodore S. Rappaport
Abstract:
This paper presents small-scale fading measurements for 28 GHz outdoor millimeter-wave ultrawideband channels using directional horn antennas at the transmitter and receiver. Power delay profiles were measured at half-wavelength spatial increments over a local area (33 wavelengths) on a linear track in two orthogonal receiver directions in a typical base-to-mobile scenario with fixed transmitter a…
▽ More
This paper presents small-scale fading measurements for 28 GHz outdoor millimeter-wave ultrawideband channels using directional horn antennas at the transmitter and receiver. Power delay profiles were measured at half-wavelength spatial increments over a local area (33 wavelengths) on a linear track in two orthogonal receiver directions in a typical base-to-mobile scenario with fixed transmitter and receiver antenna beam pointing directions. The voltage path amplitudes are shown to follow a Rician distribution, with K-factor ranging from 9 - 15 dB and 5 - 8 dB in line of sight (LOS) and non-line of sight (NLOS) for a vertical-to-vertical co-polarized antenna scenario, respectively, and from 3 - 7 dB in both LOS and NLOS vertical-to-horizontal cross-polarized antenna scenario. The average spatial autocorrelation functions of individual multipath components reveal that signal amplitudes reach a correlation of 0 after 2 and 5 wavelengths in LOS and NLOS co-polarized V-V antenna scenarios. The models provided are useful for recreating path gain statistics of millimeter-wave wideband channel impulse responses over local areas, for the study of multi-element antenna simulations and channel estimation algorithms.
△ Less
Submitted 22 February, 2016; v1 submitted 21 November, 2015;
originally announced November 2015.
-
Statistical Channel Model with Multi-Frequency and Arbitrary Antenna Beamwidth for Millimeter-Wave Outdoor Communications
Authors:
Mathew K. Samimi,
Theodore S. Rappaport
Abstract:
This paper presents a 3-dimensional millimeter-wave statistical channel impulse response model from 28 GHz and 73 GHz ultrawideband propagation measurements. An accurate 3GPP-like channel model that supports arbitrary carrier frequency, RF bandwidth, and antenna beamwidth (for both omnidirectional and arbitrary directional antennas), is provided. Time cluster and spatial lobe model parameters are…
▽ More
This paper presents a 3-dimensional millimeter-wave statistical channel impulse response model from 28 GHz and 73 GHz ultrawideband propagation measurements. An accurate 3GPP-like channel model that supports arbitrary carrier frequency, RF bandwidth, and antenna beamwidth (for both omnidirectional and arbitrary directional antennas), is provided. Time cluster and spatial lobe model parameters are extracted from empirical distributions from field measurements. A step-by-step modeling procedure for generating channel coefficients is shown to agree with statistics from the field measurements, thus confirming that the statistical channel model faithfully recreates spatial and temporal channel impulse responses for use in millimeter-wave 5G air interface designs.
△ Less
Submitted 21 November, 2015; v1 submitted 11 October, 2015;
originally announced October 2015.
-
28 GHz and 73 GHz Millimeter-Wave Indoor Propagation Measurements and Path Loss Models
Authors:
Sijia Deng,
Mathew K. Samimi,
Theodore S. Rappaport
Abstract:
This paper presents 28 GHz and 73 GHz millimeter- wave propagation measurements performed in a typical office environment using a 400 Megachip-per-second broadband sliding correlator channel sounder and highly directional steerable 15 dBi (30 degrees beamwidth) and 20 dBi (15 degrees beamwidth) horn antennas. Power delay profiles were acquired for 48 transmitter-receiver location combinations over…
▽ More
This paper presents 28 GHz and 73 GHz millimeter- wave propagation measurements performed in a typical office environment using a 400 Megachip-per-second broadband sliding correlator channel sounder and highly directional steerable 15 dBi (30 degrees beamwidth) and 20 dBi (15 degrees beamwidth) horn antennas. Power delay profiles were acquired for 48 transmitter-receiver location combinations over distances ranging from 3.9 m to 45.9 m with maximum transmit powers of 24 dBm and 12.3 dBm at 28 GHz and 73 GHz, respectively. Directional and omnidirectional path loss models and RMS delay spread statistics are presented for line-of-sight and non-line-of-sight environments for both co- and cross-polarized antenna configurations. The LOS omnidirectional path loss exponents were 1.1 and 1.3 at 28 GHz and 73 GHz, and 2.7 and 3.2 in NLOS at 28 GHz and 73 GHz, respectively, for vertically-polarized antennas. The mean directional RMS delay spreads were 18.4 ns and 13.3 ns, with maximum values of 193 ns and 288 ns at 28 GHz and 73 GHz, respectively.
△ Less
Submitted 1 September, 2015;
originally announced September 2015.
-
Probabilistic Omnidirectional Path Loss Models for Millimeter-Wave Outdoor Communications
Authors:
Mathew K. Samimi,
Theodore S. Rappaport,
George R. MacCartney Jr
Abstract:
This letter presents a probabilistic omnidirectional millimeter-wave path loss model based on real-world 28 GHz and 73 GHz measurements collected in New York City. The probabilistic path loss approach uses a free space line-of-sight propagation model, and for non-line-of-sight conditions uses either a close-in free space reference distance path loss model or a floating-intercept path loss model. T…
▽ More
This letter presents a probabilistic omnidirectional millimeter-wave path loss model based on real-world 28 GHz and 73 GHz measurements collected in New York City. The probabilistic path loss approach uses a free space line-of-sight propagation model, and for non-line-of-sight conditions uses either a close-in free space reference distance path loss model or a floating-intercept path loss model. The probabilistic model employs a weighting function that specifies the line-of-sight probability for a given transmitter-receiver separation distance. Results show that the probabilistic path loss model offers virtually identical results whether one uses a non-line-of-sight close-in free space reference distance path loss model, with a reference distance of 1 meter, or a floating-intercept path loss model. This letter also shows that site-specific environmental information may be used to yield the probabilistic weighting function for choosing between line-of-sight and non-line-of-sight conditions.
△ Less
Submitted 22 June, 2015; v1 submitted 25 March, 2015;
originally announced March 2015.
-
3-D Statistical Channel Model for Millimeter-Wave Outdoor Mobile Broadband Communications
Authors:
Mathew K. Samimi,
Theodore S. Rappaport
Abstract:
This paper presents an omnidirectional spatial and temporal 3-dimensional statistical channel model for 28 GHz dense urban non-line of sight environments. The channel model is developed from 28 GHz ultrawideband propagation measurements obtained with a 400 megachips per second broadband sliding correlator channel sounder and highly directional, steerable horn antennas in New York City. A 3GPP-like…
▽ More
This paper presents an omnidirectional spatial and temporal 3-dimensional statistical channel model for 28 GHz dense urban non-line of sight environments. The channel model is developed from 28 GHz ultrawideband propagation measurements obtained with a 400 megachips per second broadband sliding correlator channel sounder and highly directional, steerable horn antennas in New York City. A 3GPP-like statistical channel model that is easy to implement in software or hardware is developed from measured power delay profiles and a synthesized method for providing absolute propagation delays recovered from 3-D ray-tracing, as well as measured angle of departure and angle of arrival power spectra. The extracted statistics are used to implement a MATLAB-based statistical simulator that generates 3-D millimeter-wave temporal and spatial channel coefficients that reproduce realistic impulse responses of measured urban channels. The methods and model presented here can be used for millimeter-wave system-wide simulations, and air interface design and capacity analyses.
△ Less
Submitted 18 March, 2015;
originally announced March 2015.
-
Exploiting Directionality for Millimeter-Wave Wireless System Improvement
Authors:
George R. MacCartney Jr.,
Mathew K. Samimi,
Theodore S. Rappaport
Abstract:
This paper presents directional and omnidirectional RMS delay spread statistics obtained from 28 GHz and 73 GHz ultrawideband propagation measurements carried out in New York City using a 400 Megachips per second broadband sliding correlator channel sounder and highly directional steerable horn antennas. The 28 GHz measurements did not systematically seek the optimum antenna pointing angles and re…
▽ More
This paper presents directional and omnidirectional RMS delay spread statistics obtained from 28 GHz and 73 GHz ultrawideband propagation measurements carried out in New York City using a 400 Megachips per second broadband sliding correlator channel sounder and highly directional steerable horn antennas. The 28 GHz measurements did not systematically seek the optimum antenna pointing angles and resulted in 33% outage for 39 T-R separation distances within 200 m. The 73 GHz measurements systematically found the best antenna pointing angles and resulted in 14.3% outage for 35 T-R separation distances within 200 m, all for mobile height receivers. Pointing the antennas to yield the strongest received power is shown to significantly reduce RMS delay spreads in line-of-sight (LOS) environments. A new term, distance extension exponent (DEE) is defined, and used to mathematically describe the increase in coverage distance that results by combining beams from angles with the strongest received power at a given location. These results suggest that employing directionality in millimeter-wave communications systems will reduce inter-symbol interference, improve link margin at cell edges, and enhance overall system performance.
△ Less
Submitted 17 March, 2015;
originally announced March 2015.
-
Millimeter Wave Channel Modeling and Cellular Capacity Evaluation
Authors:
Mustafa Riza Akdeniz,
Yuanpeng Liu,
Mathew K. Samimi,
Shu Sun,
Sundeep Rangan,
Theodore S. Rappaport,
Elza Erkip
Abstract:
With the severe spectrum shortage in conventional cellular bands, millimeter wave (mmW) frequencies between 30 and 300 GHz have been attracting growing attention as a possible candidate for next-generation micro- and picocellular wireless networks. The mmW bands offer orders of magnitude greater spectrum than current cellular allocations and enable very high-dimensional antenna arrays for further…
▽ More
With the severe spectrum shortage in conventional cellular bands, millimeter wave (mmW) frequencies between 30 and 300 GHz have been attracting growing attention as a possible candidate for next-generation micro- and picocellular wireless networks. The mmW bands offer orders of magnitude greater spectrum than current cellular allocations and enable very high-dimensional antenna arrays for further gains via beamforming and spatial multiplexing. This paper uses recent real-world measurements at 28 and 73 GHz in New York City to derive detailed spatial statistical models of the channels and uses these models to provide a realistic assessment of mmW micro- and picocellular networks in a dense urban deployment. Statistical models are derived for key channel parameters including the path loss, number of spatial clusters, angular dispersion and outage. It is found that, even in highly non-line-of-sight environments, strong signals can be detected 100 m to 200 m from potential cell sites, potentially with multiple clusters to support spatial multiplexing. Moreover, a system simulation based on the models predicts that mmW systems can offer an order of magnitude increase in capacity over current state-of-the-art 4G cellular networks with no increase in cell density from current urban deployments.
△ Less
Submitted 25 April, 2014; v1 submitted 17 December, 2013;
originally announced December 2013.
