-
Auditory Model based Phase-Aware Bayesian Spectral Amplitude Estimator for Single-Channel Speech Enhancement
Authors:
Suman Samui,
Indrajit Chakrabarti,
Soumya K. Ghosh
Abstract:
Bayesian estimation of short-time spectral amplitude is one of the most predominant approaches for the enhancement of the noise corrupted speech. The performance of these estimators are usually significantly improved when any perceptually relevant cost function is considered. On the other hand, the recent progress in the phase-based speech signal processing have shown that the phase-only enhanceme…
▽ More
Bayesian estimation of short-time spectral amplitude is one of the most predominant approaches for the enhancement of the noise corrupted speech. The performance of these estimators are usually significantly improved when any perceptually relevant cost function is considered. On the other hand, the recent progress in the phase-based speech signal processing have shown that the phase-only enhancement based on spectral phase estimation methods can also provide joint improvement in the perceived speech quality and intelligibility, even in low SNR conditions. In this paper, to take advantage of both the perceptually motivated cost function involving STSAs of estimated and true clean speech and utilizing the prior spectral phase information, we have derived a phase-aware Bayesian STSA estimator. The parameters of the cost function are chosen based on the characteristics of the human auditory system, namely, the dynamic compressive nonlinearity of the cochlea, the perceived loudness theory and the simultaneous masking properties of the ear. This type of parameter selection scheme results in more noise reduction while limiting the speech distortion. The derived STSA estimator is optimal in the MMSE sense if the prior phase information is available. In practice, however, typically only an estimate of the clean speech phase can be obtained via employing different types of spectral phase estimation techniques which have been developed throughout the last few years. In a blind setup, we have evaluated the proposed Bayesian STSA estimator with different types of standard phase estimation methods available in the literature. Experimental results have shown that the proposed estimator can achieve substantial improvement in performance than the traditional phase-blind approaches.
△ Less
Submitted 10 February, 2022;
originally announced February 2022.
-
Acoustic Scene Analysis using Analog Spiking Neural Network
Authors:
Anand Kumar Mukhopadhyay,
Naligala Moses Prabhakar,
Divya Lakshmi Duggisetty,
Indrajit Chakrabarti,
Mrigank Sharad
Abstract:
Sensor nodes in a wireless sensor network (WSN) for security surveillance applications should preferably be small, energy-efficient, and inexpensive with in-sensor computational abilities. An appropriate data processing scheme in the sensor node reduces the power dissipation of the transceiver through the compression of information to be communicated. This study attempted a simulation-based analys…
▽ More
Sensor nodes in a wireless sensor network (WSN) for security surveillance applications should preferably be small, energy-efficient, and inexpensive with in-sensor computational abilities. An appropriate data processing scheme in the sensor node reduces the power dissipation of the transceiver through the compression of information to be communicated. This study attempted a simulation-based analysis of human footstep sound classification in natural surroundings using simple time-domain features. The spiking neural network (SNN), a computationally low-weight classifier derived from an artificial neural network (ANN), was used to classify acoustic sounds. The SNN and required feature extraction schemes are amenable to low-power subthreshold analog implementation. The results show that all analog implementations of the proposed SNN scheme achieve significant power savings over the digital implementation of the same computing scheme and other conventional digital architectures using frequency-domain feature extraction and ANN-based classification. The algorithm is tolerant of the impact of process variations, which are inevitable in analog design, owing to the approximate nature of the data processing involved in such applications. Although SNN provides low-power operation at the algorithm level itself, ANN to SNN conversion leads to an unavoidable loss of classification accuracy of ~5%. We exploited the low-power operation of the analog processing SNN module by applying redundancy and majority voting, which improved the classification accuracy, taking it close to the ANN model.
△ Less
Submitted 3 May, 2022; v1 submitted 23 December, 2019;
originally announced December 2019.
-
Runtime Mitigation of Packet Drop Attacks in Fault-tolerant Networks-on-Chip
Authors:
N Prasad,
Navonil Chatterjee,
Santanu Chattopadhyay,
Indrajit Chakrabarti
Abstract:
Fault-tolerant routing (FTR) in Networks-on-Chip (NoCs) has become a common practice to sustain the performance of multi-core systems with an increasing number of faults on a chip. On the other hand, usage of third-party intellectual property blocks has made security a primary concern in modern day designs. This article presents a mechanism to mitigate a denial-of-service attack, namely packet dro…
▽ More
Fault-tolerant routing (FTR) in Networks-on-Chip (NoCs) has become a common practice to sustain the performance of multi-core systems with an increasing number of faults on a chip. On the other hand, usage of third-party intellectual property blocks has made security a primary concern in modern day designs. This article presents a mechanism to mitigate a denial-of-service attack, namely packet drop attack, which may arise due to the hardware Trojans (HTs) in NoCs that adopt FTR algorithms. HTs, associated with external kill switches, are conditionally triggered to enable the attack scenario. Security modules, such as authentication unit, buffer shuffler, and control unit, have been proposed to thwart the attack in runtime and restore secure packet flow in the NoC. These units work together as a shield to safeguard the packets from proceeding towards the output ports with faulty links. Synthesis results show that the proposed secure FT router, when compared with a baseline FT router, has area and power overheads of at most 4.04% and 0.90%, respectively. Performance evaluation shows that SeFaR has acceptable overheads in the execution time, energy consumption, average packet latency, and power-latency product metrics when compared with a baseline FT router while running real benchmarks, as well as synthetic traffic. Further, a possible design of a comprehensive secure router has been presented with a view to addressing and mitigating multiple attacks that can arise in the NoC routers.
△ Less
Submitted 1 August, 2019;
originally announced August 2019.
-
Tensor-Train Long Short-Term Memory for Monaural Speech Enhancement
Authors:
Suman Samui,
Indrajit Chakrabarti,
Soumya K. Ghosh
Abstract:
In recent years, Long Short-Term Memory (LSTM) has become a popular choice for speech separation and speech enhancement task. The capability of LSTM network can be enhanced by widening and adding more layers. However, this would introduce millions of parameters in the network and also increase the requirement of computational resources. These limitations hinders the efficient implementation of RNN…
▽ More
In recent years, Long Short-Term Memory (LSTM) has become a popular choice for speech separation and speech enhancement task. The capability of LSTM network can be enhanced by widening and adding more layers. However, this would introduce millions of parameters in the network and also increase the requirement of computational resources. These limitations hinders the efficient implementation of RNN models in low-end devices such as mobile phones and embedded systems with limited memory. To overcome these issues, we proposed to use an efficient alternative approach of reducing parameters by representing the weight matrix parameters of LSTM based on Tensor-Train (TT) format. We called this Tensor-Train factorized LSTM as TT-LSTM model. Based on this TT-LSTM units, we proposed a deep TensorNet model for single-channel speech enhancement task. Experimental results in various test conditions and in terms of standard speech quality and intelligibility metrics, demonstrated that the proposed deep TT-LSTM based speech enhancement framework can achieve competitive performances with the state-of-the-art uncompressed RNN model, even though the proposed model architecture is orders of magnitude less complex.
△ Less
Submitted 25 December, 2018;
originally announced December 2018.
-
Power efficient Spiking Neural Network Classifier based on memristive crossbar network for spike sorting application
Authors:
Anand Kumar Mukhopadhyay,
Indrajit Chakrabarti,
Arindam Basu,
Mrigank Sharad
Abstract:
In this paper authors have presented a power efficient scheme for implementing a spike sorting module. Spike sorting is an important application in the field of neural signal acquisition for implantable biomedical systems whose function is to map the Neural-spikes (N-spikes) correctly to the neurons from which it originates. The accurate classification is a pre-requisite for the succeeding systems…
▽ More
In this paper authors have presented a power efficient scheme for implementing a spike sorting module. Spike sorting is an important application in the field of neural signal acquisition for implantable biomedical systems whose function is to map the Neural-spikes (N-spikes) correctly to the neurons from which it originates. The accurate classification is a pre-requisite for the succeeding systems needed in Brain-Machine-Interfaces (BMIs) to give better performance. The primary design constraint to be satisfied for the spike sorter module is low power with good accuracy. There lies a trade-off in terms of power consumption between the on-chip and off-chip training of the N-spike features. In the former case care has to be taken to make the computational units power efficient whereas in the later the data rate of wireless transmission should be minimized to reduce the power consumption due to the transceivers. In this work a 2-step shared training scheme involving a K-means sorter and a Spiking Neural Network (SNN) is elaborated for on-chip training and classification. Also, a low power SNN classifier scheme using memristive crossbar type architecture is compared with a fully digital implementation. The advantage of the former classifier is that it is power efficient while providing comparable accuracy as that of the digital implementation due to the robustness of the SNN training algorithm which has a good tolerance for variation in memristance.
△ Less
Submitted 25 February, 2018;
originally announced February 2018.
-
VLSI Friendly Framework for Scalable Video Coding based on Compressed Sensing
Authors:
B. K. N. Srinivasarao,
Vinay Chakravarthi Gogineni,
Subrahmanyam Mula,
Indrajit Chakrabarti
Abstract:
This paper presents a new VLSI friendly framework for scalable video coding based on Compressed Sensing (CS). It achieves scalability through 3-Dimensional Discrete Wavelet Transform (3-D DWT) and better compression ratio by exploiting the inherent sparsity of the high-frequency wavelet sub-bands through CS. By using 3-D DWT and a proposed adaptive measurement scheme called AMS at the encoder, one…
▽ More
This paper presents a new VLSI friendly framework for scalable video coding based on Compressed Sensing (CS). It achieves scalability through 3-Dimensional Discrete Wavelet Transform (3-D DWT) and better compression ratio by exploiting the inherent sparsity of the high-frequency wavelet sub-bands through CS. By using 3-D DWT and a proposed adaptive measurement scheme called AMS at the encoder, one can succeed in improving the compression ratio and reducing the complexity of the decoder. The proposed video codec uses only 7% of the total number of multipliers needed in a conventional CS-based video coding system. A codebook of Bernoulli matrices with different sizes corresponding to the predefined sparsity levels is maintained at both the encoder and the decoder. Based on the calculated l0-norm of the input vector, one of the sixteen possible Bernoulli matrices will be selected for taking the CS measurements and its index will be transmitted along with the measurements. Based on this index, the corresponding Bernoulli matrix has been used in CS reconstruction algorithm to get back the high-frequency wavelet sub-bands at the decoder. At the decoder, a new Enhanced Approximate Message Passing (EAMP) algorithm has been proposed to reconstruct the wavelet coefficients and apply the inverse wavelet transform for restoring back the video frames. Simulation results have established the superiority of the proposed framework over the existing schemes and have increased its suitability for VLSI implementation. Moreover, the coded video is found to be scalable with an increase in a number of levels of wavelet decomposition.
△ Less
Submitted 24 February, 2016;
originally announced February 2016.
-
High Speed VLSI Architecture for 3-D Discrete Wavelet Transform
Authors:
Batta Kota Naga Srinivasarao,
Indrajit Chakrabarti
Abstract:
This paper presents a memory efficient, high throughput parallel lifting based running three dimensional discrete wavelet transform (3-D DWT) architecture. 3-D DWT is constructed by combining the two spatial and four temporal processors. Spatial processor (SP) apply the two dimensional DWT on a frame, using lifting based 9/7 filter bank through the row rocessor (RP) in row direction and then apply…
▽ More
This paper presents a memory efficient, high throughput parallel lifting based running three dimensional discrete wavelet transform (3-D DWT) architecture. 3-D DWT is constructed by combining the two spatial and four temporal processors. Spatial processor (SP) apply the two dimensional DWT on a frame, using lifting based 9/7 filter bank through the row rocessor (RP) in row direction and then apply in the colum direction through column processor (CP). To reduce the temporal memory and the latency, the temporal processor (TP) has been designed with lifting based 1-D Haar wavelet filter. The proposed architecture replaced the multiplications by pipeline shift-add operations to reduce the CPD. Two spatial processors works simultaneously on two adjacent frames and provide 2-D DWT coefficients as inputs to the temporal processors. TPs apply the one dimensional DWT in temporal direction and provide eight 3-D DWT coefficients per clock (throughput). Higher throughput reduces the computing cycles per frame and enable the lower power consumption. Implementation results shows that the proposed architecture has the advantage in reduced memory, low power consumption, low latency, and high throughput over the existing designs. The RTL of the proposed architecture is described using verilog and synthesized using 90-nm technology CMOS standard cell library and results show that it consumes 43.42 mW power and occupies an area equivalent to 231.45 K equivalent gate at frequency of 200 MHz. The proposed architecture has also been synthesised for the Xilinx zynq 7020 series field programmable gate array (FPGA).
△ Less
Submitted 13 September, 2015;
originally announced September 2015.
-
Hardware Implementation of Compressed Sensing based Low Complex Video Encoder
Authors:
Batta Kota Naga Srinivasarao,
Indrajit Chakrabarti
Abstract:
This paper presents a memory efficient VLSI architecture of low complex video encoder using three dimensional (3-D) wavelet and Compressed Sensing (CS) is proposed for space and low power video applications. Majority of the conventional video coding schemes are based on hybrid model, which requires complex operations like transform coding (DCT), motion estimation and deblocking filter at the encod…
▽ More
This paper presents a memory efficient VLSI architecture of low complex video encoder using three dimensional (3-D) wavelet and Compressed Sensing (CS) is proposed for space and low power video applications. Majority of the conventional video coding schemes are based on hybrid model, which requires complex operations like transform coding (DCT), motion estimation and deblocking filter at the encoder. Complexity of the proposed encoder is reduced by replacing those complex operations by 3-D DWT and CS at the encoder. The proposed architecture uses 3-D DWT to enable the scalability with levels of wavelet decomposition and also to exploit the spatial and the temporal redundancies. CS provides the good error resilience and coding efficiency. At the first stage of the proposed architecture for encoder, 3-D DWT has been applied (Lifting based 2-D DWT in spatial domain and Haar wavelet in temporal domain) on each frame of the group of frames (GOF), and in the second stage CS module exploits the sparsity of the wavelet coefficients. Small set of linear measurements are extracted by projecting the sparse 3-D wavelet coefficients onto random Bernoulli matrix at the encoder. Compared with the best existing 3-D DWT architectures, the proposed architecture for 3-D DWT requires less memory and provide high throughput. For an N?N image, the proposed 3-D DWT architecture consumes a total of only 2?(3N +40P) words of on-chip memory for the one level of decomposition. The proposed architecture for an encoder is first of its kind and to the best of my knowledge, no architecture is noted for comparison. The proposed VLSI architecture of the encoder has been synthesized on 90-nm CMOS process technology and results show that it consumes 90.08 mW power and occupies an area equivalent to 416.799 K equivalent gate at frequency of 158 MHz.
△ Less
Submitted 13 September, 2015;
originally announced September 2015.
-
Multi-standard programmable baseband modulator for next generation wireless communication
Authors:
Indranil Hatai,
Indrajit Chakrabarti
Abstract:
Considerable research has taken place in recent times in the area of parameterization of software defined radio (SDR) architecture. Parameterization decreases the size of the software to be downloaded and also limits the hardware reconfiguration time. The present paper is based on the design and development of a programmable baseband modulator that perform the QPSK modulation schemes and as well a…
▽ More
Considerable research has taken place in recent times in the area of parameterization of software defined radio (SDR) architecture. Parameterization decreases the size of the software to be downloaded and also limits the hardware reconfiguration time. The present paper is based on the design and development of a programmable baseband modulator that perform the QPSK modulation schemes and as well as its other three commonly used variants to satisfy the requirement of several established 2G and 3G wireless communication standards. The proposed design has been shown to be capable of operating at a maximum data rate of 77 Mbps on ** root raised cosine (RRC) filter has been implemented using distributed arithmetic (DA) technique in the present work in order to reduce the computational complexity, and to achieve appropriate power reduction and enhanced throughput. The designed multiplier-less programmable 32-tap FIR-based RRC filter has been found to withstand a peak inter-symbol interference (ISI) distortion of -41 dBs
△ Less
Submitted 9 September, 2010;
originally announced September 2010.
