-
Multiphase Flow Simulation of Blow-by and Fuel-in-Oil Dilution via the Piston Ring Pack Using the CFD Level-Set Method
Authors:
Patrick Antony,
Norbert Hosters,
Marek Behr,
Anselm Hopf,
Frank Krämer,
Carsten Weber,
Paul Turner
Abstract:
Modern diesel engines temporarily use a very late post-injection in the combustion cycle to either generate heat for a diesel particulate filter regeneration or purge a lean NOx trap. In some configurations, unburned fuel is left at the cylinder walls and is transported via the piston rings toward the lower crankcase region, where fuel may dilute the oil. Reduced oil lubrication shortens the oil s…
▽ More
Modern diesel engines temporarily use a very late post-injection in the combustion cycle to either generate heat for a diesel particulate filter regeneration or purge a lean NOx trap. In some configurations, unburned fuel is left at the cylinder walls and is transported via the piston rings toward the lower crankcase region, where fuel may dilute the oil. Reduced oil lubrication shortens the oil service intervals and increases friction. Beside diesel fuel, this problem may also occur for other types of liquid fuels such as alcohols and e-fuels. The exact transport mechanism of the unburned fuel via the piston ring pack grooves and cylinder wall is hard to measure experimentally, motivating numerical flow simulation in early design stages for an in-depth understanding of the involved processes. A new CFD simulation methodology has been developed to investigate the transient, compressible, multiphase flow around the piston ring pack, through the gap between piston and liner, and its impact on fuel or oil transport. The modern level-set approach is used for the multiphase physics, which directly captures the sharp interface between blow-by gas and fuel or oil. Transient blow-by and two-phase flow simulations have been extensively applied to a Ford 2.0L I4 diesel test engine. The results confirm the validity of the flow compressibility assumption and highlight the sensitivity of the fuel leakage regarding piston sealing ring movement and highly resolved meshes for the multiphase flow. Based on the simulation results, design recommendations for piston and piston ring geometry are provided to reduce the fuel transport toward the crankcase.
△ Less
Submitted 4 June, 2024;
originally announced June 2024.
-
A Model Hierarchy for Predicting the Flow in Stirred Tanks with Physics-Informed Neural Networks
Authors:
Veronika Trávníková,
Daniel Wolff,
Nico Dirkes,
Stefanie Elgeti,
Eric von Lieres,
Marek Behr
Abstract:
This paper explores the potential of Physics-Informed Neural Networks (PINNs) to serve as Reduced Order Models (ROMs) for simulating the flow field within stirred tank reactors (STRs). We solve the two-dimensional stationary Navier-Stokes equations within a geometrically intricate domain and explore methodologies that allow us to integrate additional physical insights into the model. These approac…
▽ More
This paper explores the potential of Physics-Informed Neural Networks (PINNs) to serve as Reduced Order Models (ROMs) for simulating the flow field within stirred tank reactors (STRs). We solve the two-dimensional stationary Navier-Stokes equations within a geometrically intricate domain and explore methodologies that allow us to integrate additional physical insights into the model. These approaches include imposing the Dirichlet boundary conditions (BCs) strongly and employing domain decomposition (DD), with both overlap** and non-overlap** subdomains. We adapt the Extended Physics-Informed Neural Network (XPINN) approach to solve different sets of equations in distinct subdomains based on the diverse flow characteristics present in each region. Our exploration results in a hierarchy of models spanning various levels of complexity, where the best models exhibit l1 prediction errors of less than 1% for both pressure and velocity. To illustrate the reproducibility of our approach, we track the errors over repeated independent training runs of the best identified model and show its reliability. Subsequently, by incorporating the stirring rate as a parametric input, we develop a fast-to-evaluate model of the flow capable of interpolating across a wide range of Reynolds numbers. Although we exclusively restrict ourselves to STRs in this work, we conclude that the steps taken to obtain the presented model hierarchy can be transferred to other applications.
△ Less
Submitted 7 March, 2024;
originally announced March 2024.
-
Eulerian Formulation of the Tensor-Based Morphology Equations for Strain-Based Blood Damage Modeling
Authors:
Nico Dirkes,
Fabian Key,
Marek Behr
Abstract:
The development of blood-handling medical devices, such as ventricular assist devices, requires the analysis of their biocompatibility. Among other aspects, this includes hemolysis, i.e., red blood cell damage. For this purpose, computational fluid dynamics (CFD) methods are employed to predict blood flow in prototypes. The most basic hemolysis models directly estimate red blood cell damage from f…
▽ More
The development of blood-handling medical devices, such as ventricular assist devices, requires the analysis of their biocompatibility. Among other aspects, this includes hemolysis, i.e., red blood cell damage. For this purpose, computational fluid dynamics (CFD) methods are employed to predict blood flow in prototypes. The most basic hemolysis models directly estimate red blood cell damage from fluid stress in the resulting flow field. More advanced models explicitly resolve cell deformation. On the downside, these models are typically written in a Lagrangian formulation, i.e., they require pathline tracking. We present a new Eulerian description of cell deformation, enabling the evaluation of the solution across the whole domain. The resulting hemolysis model can be applied to any converged CFD simulation due to one-way coupling with the fluid velocity field. We discuss the efficient numerical treatment of the model equations in a stabilized finite element context. We verify the model by comparison to the original Lagrangian formulation in selected benchmark flows. Two more complex test cases demonstrate the method's capabilities in real-world applications. The results highlight the advantages over previous hemolysis models. In conclusion, the model holds great potential for the design process of future generations of medical devices.
△ Less
Submitted 11 April, 2024; v1 submitted 14 February, 2024;
originally announced February 2024.
-
Computational modeling of in-stent restenosis: Pharmacokinetic and pharmacodynamic evaluation
Authors:
Kiran Manjunatha,
Nicole Schaaps,
Marek Behr,
Felix Vogt,
Stefanie Reese
Abstract:
Persistence of the pathology of in-stent restenosis even with the advent of drug-eluting stents warrants the development of highly resolved in silico models. These computational models assist in gaining insights into the transient biochemical and cellular mechanisms involved and thereby optimize the stent implantation parameters. Within this work, an already established fully-coupled Lagrangian fi…
▽ More
Persistence of the pathology of in-stent restenosis even with the advent of drug-eluting stents warrants the development of highly resolved in silico models. These computational models assist in gaining insights into the transient biochemical and cellular mechanisms involved and thereby optimize the stent implantation parameters. Within this work, an already established fully-coupled Lagrangian finite element framework for modeling the restenotic growth is enhanced with the incorporation of endothelium-mediated effects and pharmacological influences of rapamycin-based drugs embedded in the polymeric layers of the current generation drug-eluting stents. The continuum mechanical description of growth is further justified in the context of thermodynamic consistency. Qualitative inferences are drawn from the model developed herein regarding the efficacy of the level of drug embedment within the struts as well as the release profiles adopted. The framework is then intended to serve as a tool for clinicians to tune the interventional procedures patient-specifically.
△ Less
Submitted 26 July, 2023; v1 submitted 24 July, 2023;
originally announced July 2023.
-
Simplex space-time meshes in engineering applications with moving domains
Authors:
Violeta Karyofylli,
Marek Behr
Abstract:
This paper highlights how unstructured space-time meshes can be used in production engineering applications with moving domains. Unstructured space-time elements can connect different spatial meshes at the bottom and top level of the space-time domain and deal with complicated domain movements/rotations that the standard arbitrary Lagrangian-Eulerian techniques can not resolve without remeshing. W…
▽ More
This paper highlights how unstructured space-time meshes can be used in production engineering applications with moving domains. Unstructured space-time elements can connect different spatial meshes at the bottom and top level of the space-time domain and deal with complicated domain movements/rotations that the standard arbitrary Lagrangian-Eulerian techniques can not resolve without remeshing. We use a space-time finite element discretization, by means of 4D simplex space-time elements, referred to as pentatopes by Behr [2008], which leads to entirely unstructured grids with varying levels of refinement both in space and in time. Furthermore, we use stabilization techniques, and the stabilization parameter is defined based on the contravariant metric tensor, as shown in the work of Pauli and Behr [2017]. Its definition was extended in 4D by von Danwitz et al. [2019], allowing us to deal with complex anisotropic simplex meshes in the space-time domain.
△ Less
Submitted 17 October, 2022;
originally announced October 2022.
-
Face-Dubbing++: Lip-Synchronous, Voice Preserving Translation of Videos
Authors:
Alexander Waibel,
Moritz Behr,
Fevziye Irem Eyiokur,
Dogucan Yaman,
Tuan-Nam Nguyen,
Carlos Mullov,
Mehmet Arif Demirtas,
Alperen Kantarcı,
Stefan Constantin,
Hazım Kemal Ekenel
Abstract:
In this paper, we propose a neural end-to-end system for voice preserving, lip-synchronous translation of videos. The system is designed to combine multiple component models and produces a video of the original speaker speaking in the target language that is lip-synchronous with the target speech, yet maintains emphases in speech, voice characteristics, face video of the original speaker. The pipe…
▽ More
In this paper, we propose a neural end-to-end system for voice preserving, lip-synchronous translation of videos. The system is designed to combine multiple component models and produces a video of the original speaker speaking in the target language that is lip-synchronous with the target speech, yet maintains emphases in speech, voice characteristics, face video of the original speaker. The pipeline starts with automatic speech recognition including emphasis detection, followed by a translation model. The translated text is then synthesized by a Text-to-Speech model that recreates the original emphases mapped from the original sentence. The resulting synthetic voice is then mapped back to the original speakers' voice using a voice conversion model. Finally, to synchronize the lips of the speaker with the translated audio, a conditional generative adversarial network-based model generates frames of adapted lip movements with respect to the input face image as well as the output of the voice conversion model. In the end, the system combines the generated video with the converted audio to produce the final output. The result is a video of a speaker speaking in another language without actually knowing it. To evaluate our design, we present a user study of the complete system as well as separate evaluations of the single components. Since there is no available dataset to evaluate our whole system, we collect a test set and evaluate our system on this test set. The results indicate that our system is able to generate convincing videos of the original speaker speaking the target language while preserving the original speaker's characteristics. The collected dataset will be shared.
△ Less
Submitted 9 June, 2022;
originally announced June 2022.
-
A multiphysics modeling approach for in-stent restenosis: Theoretical aspects and finite element implementation
Authors:
Kiran Manjunatha,
Marek Behr,
Felix Vogt,
Stefanie Reese
Abstract:
Development of in silico models are intrinsic in understanding disease progression in soft biological tissues. Within this work, we propose a fully-coupled Lagrangian finite element framework which replicates the process of in-stent restenosis observed post stent implantation in a coronary artery. Coupled advection-reaction-diffusion reactions are set up that track the evolution of the concentrati…
▽ More
Development of in silico models are intrinsic in understanding disease progression in soft biological tissues. Within this work, we propose a fully-coupled Lagrangian finite element framework which replicates the process of in-stent restenosis observed post stent implantation in a coronary artery. Coupled advection-reaction-diffusion reactions are set up that track the evolution of the concentrations of the platelet-derived growth factor, the transforming growth factor-$β$, the extracellular matrix, and the density of the smooth muscle cells. A continuum mechanical description of growth incorporating the evolution of arterial wall constituents is developed, and a suitable finite element implementation discussed. Qualitative validation of the computational model are presented by emulating a stented artery. Patient-specific data can be integrated into the model to predict the risk of restenosis and thereby assist in tuning of stent implantation parameters to mitigate the risk.
△ Less
Submitted 7 April, 2022; v1 submitted 5 April, 2022;
originally announced April 2022.
-
Spline-Based Space-Time Finite Element Approach for Fluid-Structure Interaction Problems With a Focus on Fully Enclosed Domains
Authors:
Michel Make,
Thomas Spenke,
Norbert Hosters,
Marek Behr
Abstract:
Non-Uniform Rational B-Spline (NURBS) surfaces are commonly used within Computer-Aided Design (CAD) tools to represent geometric objects. When using isogeometric analysis (IGA), it is possible to use such NURBS geometries for numerical analysis directly. Analyzing fluid flows, however, requires complex three-dimensional geometries to represent flow domains. Defining a parametrization of such volum…
▽ More
Non-Uniform Rational B-Spline (NURBS) surfaces are commonly used within Computer-Aided Design (CAD) tools to represent geometric objects. When using isogeometric analysis (IGA), it is possible to use such NURBS geometries for numerical analysis directly. Analyzing fluid flows, however, requires complex three-dimensional geometries to represent flow domains. Defining a parametrization of such volumetric domains using NURBS can be challenging and is still an ongoing topic in the IGA community. With the recently developed NURBS-enhanced finite element method (NEFEM), the favorable geometric characteristics of NURBS are used within a standard finite element method. This is achieved by enhancing the elements touching the boundary by using the NURBS geometry itself. In the current work, a new variation of NEFEM is introduced, which is suitable for three-dimensional space-time finite element formulations. The proposed method makes use of a new map** which results in a non-Cartesian formulation suitable for fluid-structure interaction (FSI). This is demonstrated by combining the method with an IGA formulation in a strongly-coupled partitioned framework for solving FSI problems. The framework yields a fully spline-based representation of the fluid-structure interface through a single NURBS. The coupling conditions at the fluid-structure interface are enforced through a Robin-Neumann type coupling scheme. This scheme is particularly useful when considering incompressible fluids in fully Dirichlet-bounded and curved problems, as it satisfies the incompressibility constraint on the fluid for each step within the coupling procedure. The accuracy and performance of the introduced spline-based space-time finite element approach and its use within the proposed coupled FSI framework are demonstrated using a series of two- and three-dimensional benchmark problems.
△ Less
Submitted 30 March, 2022;
originally announced March 2022.
-
Stabilized finite element methods for a fully-implicit logarithmic reformulation of the Oldroyd-B constitutive law
Authors:
Stefan Wittschieber,
Leszek Demkowicz,
Marek Behr
Abstract:
Logarithmic conformation reformulations for viscoelastic constitutive laws have alleviated the high Weissenberg number problem, and the exploration of highly elastic flows became possible. However, stabilized formulations for logarithmic conformation reformulations in the context of finite element methods have not yet been widely studied. We present stabilized formulations for the logarithmic refo…
▽ More
Logarithmic conformation reformulations for viscoelastic constitutive laws have alleviated the high Weissenberg number problem, and the exploration of highly elastic flows became possible. However, stabilized formulations for logarithmic conformation reformulations in the context of finite element methods have not yet been widely studied. We present stabilized formulations for the logarithmic reformulation of the Oldroyd-B model by Saramito (2014) based on the Variational Multiscale framework and Galerkin/Least-Squares method. The reformulation allows the use of Newton's method due to its fully-implicit nature for solving the steady-state problem directly. The proposed stabilization methods cure instabilities of convection and compatibility while preserving a three-field problem. The spatial accuracy of the formulations is assessed with the four-roll periodic box, revealing comparable accuracy between the methods. The formulations are validated with benchmark flows past a cylinder and through a 4:1 contraction. We found an excellent agreement to benchmark results in the literature. The algebraic sub-grid scale method is highly robust, indicated by the high limiting Weissenberg numbers in the benchmark flows.
△ Less
Submitted 13 December, 2021;
originally announced December 2021.
-
The Performance Impact of Newton Iterations per Solver Call in Partitioned Fluid-Structure Interaction
Authors:
Thomas Spenke,
Norbert Hosters,
Marek Behr
Abstract:
The cost of a partitioned fluid-structure interaction scheme is typically assessed by the number of coupling iterations required per time step, while ignoring the Newton loops within the nonlinear sub-solvers. In this work, we discuss why these single-field iterations deserve more attention when evaluating the coupling's efficiency and how to find the optimal number of Newton steps per coupling it…
▽ More
The cost of a partitioned fluid-structure interaction scheme is typically assessed by the number of coupling iterations required per time step, while ignoring the Newton loops within the nonlinear sub-solvers. In this work, we discuss why these single-field iterations deserve more attention when evaluating the coupling's efficiency and how to find the optimal number of Newton steps per coupling iteration.
△ Less
Submitted 30 June, 2021;
originally announced June 2021.
-
Simulating dense granular flow using the $μ$($I$)-rheology within a space-time framework
Authors:
Linda Gesenhues,
Marek Behr
Abstract:
A space-time framework is applied to simulate dense granular flow. Two different numerical experiments are performed: a column collapse and a dam break on an inclined plane. The experiments are modeled as two-phase flows. The dense granular material is represented by a constitutive model, the $μ$($I$)-rheology, that is based on the Coulomb's friction law, such that the normal stress applied by the…
▽ More
A space-time framework is applied to simulate dense granular flow. Two different numerical experiments are performed: a column collapse and a dam break on an inclined plane. The experiments are modeled as two-phase flows. The dense granular material is represented by a constitutive model, the $μ$($I$)-rheology, that is based on the Coulomb's friction law, such that the normal stress applied by the pressure is related to the tangential stress. The model represents a complex shear thinning viscoplastic material behavior. The interface between the dense granular material and the surrounding light fluid is captured with a level set function. Due to discontinuities close to the the interface, the mesh requires a sufficient resolution. The space-time approach allows unstructured meshes in time and, therefore a well refined mesh in the temporal direction around the interface. In this study, results and performance of a flat and a simplex space time discretization are verified and analyzed.
△ Less
Submitted 9 February, 2021;
originally announced February 2021.
-
A novel approach to fluid-structure interaction simulations involving large translation and contact
Authors:
Daniel Hilger,
Norbert Hosters,
Fabian Key,
Stefanie Elgeti,
Marek Behr
Abstract:
In this work, we present a novel method for the mesh update in flow problems with moving boundaries, the phantom domain deformation mesh update method (PD-DMUM). The PD-DMUM is designed to avoid remeshing; even in the event of large, unidirectional displacements of boundaries. The method combines the concept of two mesh adaptation approaches: (1) The virtual ring shear-slip mesh updatemethod (VR-S…
▽ More
In this work, we present a novel method for the mesh update in flow problems with moving boundaries, the phantom domain deformation mesh update method (PD-DMUM). The PD-DMUM is designed to avoid remeshing; even in the event of large, unidirectional displacements of boundaries. The method combines the concept of two mesh adaptation approaches: (1) The virtual ring shear-slip mesh updatemethod (VR-SSMUM); and (2) the elastic mesh update method (EMUM). As in the VR-SSMUM, the PD-DMUMextends the fluid domain by a phantom domain; the PD-DMUM can thus locally adapt the element density. Combined with the EMUM, the PD-DMUMallows the consideration of arbitrary boundary movements. In this work, we apply the PD-DMUM in two test cases. Within the first test case, we validate the PD-DMUM in a 2D Poiseuille flow on a moving background mesh. Subsequently the fluid-structure interaction (FSI) problem in the second test case serves as a proof of concept. More, we stress the advantages of the novel method with regard to conventional mesh update approaches.
△ Less
Submitted 13 January, 2021;
originally announced January 2021.
-
Finite element modelling of in-stent restenosis
Authors:
Kiran Manjunatha,
Marek Behr,
Felix Vogt,
Stefanie Reese
Abstract:
From the perspective of coronary heart disease, the development of stents has come significantly far in reducing the associated mortality rate, drug-eluting stents being the epitome of innovative and effective solutions. Within this work, the intricate process of in-stent restenosis is modelled considering one of the significant growth factors and its effect on constituents of the arterial wall. A…
▽ More
From the perspective of coronary heart disease, the development of stents has come significantly far in reducing the associated mortality rate, drug-eluting stents being the epitome of innovative and effective solutions. Within this work, the intricate process of in-stent restenosis is modelled considering one of the significant growth factors and its effect on constituents of the arterial wall. A multiphysical modelling approach is adopted in this regard. Experimental investigations from the literature have been used to hypothesize the governing equations and the corresponding parameters. A staggered solution strategy is utilised to capture the transport phenomena as well as the growth and remodeling that follows stent implantation. The model herein developed serves as a tool to predict in-stent restenosis depending on the endothelial injury sustained and the protuberance of stents into the lumen of the arteries. Keywords: in-stent restenosis, smooth mucsle cells, platelet-derived growth factor, extracellular matrix, growth
△ Less
Submitted 14 December, 2020; v1 submitted 5 December, 2020;
originally announced December 2020.
-
A Multi-Vector Interface Quasi-Newton Method with Linear Complexity for Partitioned Fluid-Structure Interaction
Authors:
Thomas Spenke,
Norbert Hosters,
Marek Behr
Abstract:
In recent years, interface quasi-Newton methods have gained growing attention in the fluid-structure interaction community by significantly improving partitioned solution schemes: They not only help to control the inherent added-mass instability, but also prove to substantially speed up the coupling's convergence. In this work, we present a novel variant: The key idea is to build on the multi-vect…
▽ More
In recent years, interface quasi-Newton methods have gained growing attention in the fluid-structure interaction community by significantly improving partitioned solution schemes: They not only help to control the inherent added-mass instability, but also prove to substantially speed up the coupling's convergence. In this work, we present a novel variant: The key idea is to build on the multi-vector Jacobian update scheme first presented by Bogaers et al. (2014) and avoid any explicit representation of the (inverse) Jacobian approximation, since it slows down the solution for large systems. Instead, all terms involving a quadratic complexity have been systematically eliminated. The result is a new multi-vector interface quasi-Newton variant whose computational cost scales linearly with the problem size.
△ Less
Submitted 22 January, 2020;
originally announced January 2020.
-
Simplex space-time meshes in two-phase flow simulations
Authors:
Violeta Karyofylli,
Markus Frings,
Stefanie Elgeti,
Marek Behr
Abstract:
In this paper, we present the numerical solution of two-phase flow problems of engineering significance with a space-time finite element method that allows for local temporal refinement. Our basis is the method presented in [3], which allows for arbitrary temporal refinement in preselected regions of the mesh. It has been extended to adaptive temporal refinement that is governed by a quantity that…
▽ More
In this paper, we present the numerical solution of two-phase flow problems of engineering significance with a space-time finite element method that allows for local temporal refinement. Our basis is the method presented in [3], which allows for arbitrary temporal refinement in preselected regions of the mesh. It has been extended to adaptive temporal refinement that is governed by a quantity that is part of the solution process, namely, the interface position in two-phase flow. Due to local effects such as surface tension, jumps in material properties, etc., the interface can, in general, be considered a region that requires high flexibility and high resolution, both in space and in time. The new method, which leads to tetrahedral (for 2D problems) and pentatope (for 3D problems) meshes, offers an efficient yet accurate approach to the underlying two-phase flow problems.
△ Less
Submitted 21 March, 2019;
originally announced March 2019.
-
Simplex space-time meshes in thermally coupled two-phase flow simulations of mold filling
Authors:
Violeta Karyofylli,
Loic Wendling,
Michel Make,
Norbert Hosters,
Marek Behr
Abstract:
The quality of plastic parts produced through injection molding depends on many factors. Especially during the filling stage, defects such as weld lines, burrs, or insufficient filling can occur. Numerical methods need to be employed to improve product quality by means of predicting and simulating the injection molding process. In the current work, a highly viscous incompressible non-isothermal tw…
▽ More
The quality of plastic parts produced through injection molding depends on many factors. Especially during the filling stage, defects such as weld lines, burrs, or insufficient filling can occur. Numerical methods need to be employed to improve product quality by means of predicting and simulating the injection molding process. In the current work, a highly viscous incompressible non-isothermal two-phase flow is simulated, which takes place during the cavity filling. The injected melt exhibits a shear-thinning behavior, which is described by the Carreau-WLF model. Besides that, a novel discretization method is used in the context of 4D simplex space-time grids [2]. This method allows for local temporal refinement in the vicinity of, e.g., the evolving front of the melt [10]. Utilizing such an adaptive refinement can lead to locally improved numerical accuracy while maintaining the highest possible computational efficiency in the remaining of the domain. For demonstration purposes, a set of 2D and 3D benchmark cases, that involve the filling of various cavities with a distributor, are presented.
△ Less
Submitted 20 March, 2019;
originally announced March 2019.
-
Boundary-Conforming Finite Element Methods for Twin-Screw Extruders: Unsteady - Temperature-Dependent - Non-Newtonian Simulations
Authors:
Jan Helmig,
Marek Behr,
Stefanie Elgeti
Abstract:
We present a boundary-conforming space-time finite element method to compute the flow inside co-rotating, self-wi** twin-screw extruders. The mesh update is carried out using the newly developed Snap** Reference Mesh Update Method (SRMUM). It allows to compute time-dependent flow solutions inside twin-screw extruders equipped with conveying screw elements without any need for re-meshing and pr…
▽ More
We present a boundary-conforming space-time finite element method to compute the flow inside co-rotating, self-wi** twin-screw extruders. The mesh update is carried out using the newly developed Snap** Reference Mesh Update Method (SRMUM). It allows to compute time-dependent flow solutions inside twin-screw extruders equipped with conveying screw elements without any need for re-meshing and projections of solutions - making it a very efficient method. We provide cases for Newtonian and non-Newtonian fluids in 2D and 3D, that show mesh convergence of the solution as well as agreement to experimental results. Furthermore, a complex, unsteady and temperature-dependent 3D test case with multiple screw elements illustrates the potential of the method also for industrial applications.
△ Less
Submitted 4 December, 2018;
originally announced January 2019.
-
Example Setups of Navier-Stokes Equations with Control and Observation: Spatial Discretization and Representation via Linear-quadratic Matrix Coefficients
Authors:
Maximilian Behr,
Peter Benner,
Jan Heiland
Abstract:
We provide spatial discretizations of nonlinear incompressible Navier-Stokes equations with inputs and outputs in the form of matrices ready to use in any numerical linear algebra package. We discuss the assembling of the system operators and the realization of boundary conditions and inputs and outputs. We describe the two benchmark problems - the driven cavity and the cylinder wake - and provide…
▽ More
We provide spatial discretizations of nonlinear incompressible Navier-Stokes equations with inputs and outputs in the form of matrices ready to use in any numerical linear algebra package. We discuss the assembling of the system operators and the realization of boundary conditions and inputs and outputs. We describe the two benchmark problems - the driven cavity and the cylinder wake - and provide the corresponding data. The use of the data is illustrated by numerous example setups. The test cases are provided as plain PYTHON or OCTAVE/MATLAB script files for immediate replication.
△ Less
Submitted 27 July, 2017;
originally announced July 2017.
-
Automatic implementation of material laws: Jacobian calculation in a finite element code with TAPENADE
Authors:
Florian Zwicke,
Philipp Knechtges,
Marek Behr,
Stefanie Elgeti
Abstract:
In an effort to increase the versatility of finite element codes, we explore the possibility of automatically creating the Jacobian matrix necessary for the gradient-based solution of nonlinear systems of equations. Particularly, we aim to assess the feasibility of employing the automatic differentiation tool TAPENADE for this purpose on a large Fortran codebase that is the result of many years of…
▽ More
In an effort to increase the versatility of finite element codes, we explore the possibility of automatically creating the Jacobian matrix necessary for the gradient-based solution of nonlinear systems of equations. Particularly, we aim to assess the feasibility of employing the automatic differentiation tool TAPENADE for this purpose on a large Fortran codebase that is the result of many years of continuous development. As a starting point we will describe the special structure of finite element codes and the implications that this code design carries for an efficient calculation of the Jacobian matrix. We will also propose a first approach towards improving the efficiency of such a method. Finally, we will present a functioning method for the automatic implementation of the Jacobian calculation in a finite element software, but will also point out important shortcomings that will have to be addressed in the future.
△ Less
Submitted 21 February, 2017;
originally announced February 2017.
