Showing 1–38 of 38 results for author: Roukes, M

Hot Carrier Thermalization and Josephson Inductance Thermometry in a Graphene-based Microwave Circuit

Authors: Raj Katti, Harpreet Arora, Olli-Pentti Saira, Kenji Watanabe, Takashi Taniguchi, Keith C. Schwab, Michael Roukes, Stevan Nadj-Perge

Abstract: Due to its exceptional electronic and thermal properties, graphene is a key material for bolometry, calorimetry, and photon detection. However, despite graphene's relatively simple electronic structure, the physical processes responsible for the transport of heat from the electrons to the lattice are experimentally still elusive. Here, we measure the thermal response of low-disorder graphene encap… ▽ More Due to its exceptional electronic and thermal properties, graphene is a key material for bolometry, calorimetry, and photon detection. However, despite graphene's relatively simple electronic structure, the physical processes responsible for the transport of heat from the electrons to the lattice are experimentally still elusive. Here, we measure the thermal response of low-disorder graphene encapsulated in hexagonal boron nitride (hBN) by integrating it within a multi-terminal superconducting device coupled to a microwave resonator. This technique allows us to simultaneously apply Joule heat power to the graphene flake while performing calibrated readout of the electron temperature. We probe the thermalization rates of both electrons and holes with high precision and observe a thermalization scaling exponent consistent with cooling dominated by resonant electron-phonon coupling processes occurring at the interface between graphene and superconducting leads. The technique utilized here is applicable for wide range of semiconducting-superconducting interface heterostructures and provides new insights into the thermalization pathways essential for the next-generation thermal detectors. △ Less

Submitted 29 August, 2022; originally announced August 2022.

Comments: main text and supplementary information

Modification of electron-phonon coupling by micromachining and suspension

Authors: Olli-Pentti Saira, Matthew H. Matheny, Libin Wang, Jukka Pekola, Michael Roukes

Abstract: Weak electron-phonon interaction in metals at low temperatures forms the basis of operation for cryogenic hot-electron bolometers and calorimeters. Standard power laws, describing the heat flow in the majority of experiments, have been identified and derived theoretically. However, a full picture encompassing experimentally relevant effects such as reduced dimensionality, material interfaces, and… ▽ More Weak electron-phonon interaction in metals at low temperatures forms the basis of operation for cryogenic hot-electron bolometers and calorimeters. Standard power laws, describing the heat flow in the majority of experiments, have been identified and derived theoretically. However, a full picture encompassing experimentally relevant effects such as reduced dimensionality, material interfaces, and disorder is in its infancy, and has not been tested extensively. Here, we study the electron-phonon heat flow in a thin gold film on a SiO${}_2$ platform below 100 mK using supercurrent thermometry. We find the power law exponent to be modified from 5.1 to 4.6 as the platform is micromachined and released from its substrate. We attribute this change to a modified phonon spectrum. The findings are compared to past experiments and theoretical models. △ Less

Submitted 22 October, 2019; originally announced October 2019.

Comments: 9 pages, 6 figures

Journal ref: J Appl. Phys. 127, 024307 (2020)

Nonequilibrium thermodynamics of erasure with superconducting flux logic

Authors: Olli-Pentti Saira, Matthew H. Matheny, Raj Katti, Warren Fon, Gregory Wimsatt, James P. Crutchfield, Siyuan Han, Michael L. Roukes

Abstract: We implement a thermal-fluctuation driven logical bit reset on a superconducting flux logic cell. We show that the logical state of the system can be continuously monitored with only a small perturbation to the thermally activated dynamics at 500 mK. We use the trajectory information to derive a single-shot estimate of the work performed on the system per logical cycle. We acquire a sample of… ▽ More We implement a thermal-fluctuation driven logical bit reset on a superconducting flux logic cell. We show that the logical state of the system can be continuously monitored with only a small perturbation to the thermally activated dynamics at 500 mK. We use the trajectory information to derive a single-shot estimate of the work performed on the system per logical cycle. We acquire a sample of $10^5$ erasure trajectories per protocol, and show that the work histograms agree with both microscopic theory and global fluctuation theorems. The results demonstrate how to design and diagnose complex, high-speed, and thermodynamically efficient computing using superconducting technology. △ Less

Submitted 30 September, 2019; originally announced September 2019.

Comments: 9 pages, 7 figures

Journal ref: Phys. Rev. Research 2, 013249 (2020)

Harnessing Fluctuations in Thermodynamic Computing via Time-Reversal Symmetries

Authors: Gregory Wimsatt, Olli-Pentti Saira, Alexander B. Boyd, Matthew H. Matheny, Siyuan Han, Michael L. Roukes, James P. Crutchfield

Abstract: We experimentally demonstrate that highly structured distributions of work emerge during even the simple task of erasing a single bit. These are signatures of a refined suite of time-reversal symmetries in distinct functional classes of microscopic trajectories. As a consequence, we introduce a broad family of conditional fluctuation theorems that the component work distributions must satisfy. Sin… ▽ More We experimentally demonstrate that highly structured distributions of work emerge during even the simple task of erasing a single bit. These are signatures of a refined suite of time-reversal symmetries in distinct functional classes of microscopic trajectories. As a consequence, we introduce a broad family of conditional fluctuation theorems that the component work distributions must satisfy. Since they identify entropy production, the component work distributions encode both the frequency of various mechanisms of success and failure during computing, as well giving improved estimates of the total irreversibly-dissipated heat. This new diagnostic tool provides strong evidence that thermodynamic computing at the nanoscale can be constructively harnessed. We experimentally verify this functional decomposition and the new class of fluctuation theorems by measuring transitions between flux states in a superconducting circuit. △ Less

Submitted 27 June, 2019; originally announced June 2019.

Comments: 13 pages, 3 figures, supplementary material; http://csc.ucdavis.edu/~cmg/compmech/pubs/tcft.htm

Journal ref: Phys. Rev. Research 3, 033115 (2021)

Resonantly induced friction in driven nanomechanical systems

Authors: Mark Dykman, Gianluca Rastelli, M. L. Roukes, Eva M. Weig

Abstract: We propose a new mechanism of friction in resonantly driven vibrational systems. The form of the friction force follows from the time- and spatial-symmetry arguments. We consider a microscopic mechanism of this resonant force in nanomechanical systems. The friction can be negative, leading to an instability of forced vibrations of a nanoresonator and the onset of self-sustained oscillations in the… ▽ More We propose a new mechanism of friction in resonantly driven vibrational systems. The form of the friction force follows from the time- and spatial-symmetry arguments. We consider a microscopic mechanism of this resonant force in nanomechanical systems. The friction can be negative, leading to an instability of forced vibrations of a nanoresonator and the onset of self-sustained oscillations in the rotating frame. △ Less

Submitted 20 March, 2019; originally announced March 2019.

Journal ref: Phys. Rev. Lett. 122, 254301 (2019)

Nonlinear dam** and dephasing in nanomechanical systems

Authors: J. Atalaya, T. W. Kenny, M. L. Roukes, M. I. Dykman

Abstract: We present a microscopic theory of nonlinear dam** and dephasing of low-frequency eigenmodes in nano- and micro-mechanical systems. The mechanism of the both effects is scattering of thermally excited vibrational modes off the considered eigenmode. The scattering is accompanied by energy transfer of $2\hbarω_0$ for nonlinear dam** and is quasieleastic for dephasing. We develop a formalism that… ▽ More We present a microscopic theory of nonlinear dam** and dephasing of low-frequency eigenmodes in nano- and micro-mechanical systems. The mechanism of the both effects is scattering of thermally excited vibrational modes off the considered eigenmode. The scattering is accompanied by energy transfer of $2\hbarω_0$ for nonlinear dam** and is quasieleastic for dephasing. We develop a formalism that allows studying both spatially uniform systems and systems with a strong nonuniformity, which is smooth on the typical wavelength of thermal modes but not their mean free path. The formalism accounts for the decay of thermal modes, which plays a major role in the nonlinear dam** and dephasing. We identify the nonlinear analogs of the Landau-Rumer, thermoelastic, and Akhiezer mechanisms and find the dependence of the relaxation parameters on the temperature and the geometry of a system. △ Less

Submitted 27 September, 2016; originally announced September 2016.

Journal ref: Phys. Rev. B 94, 195440 (2016)

Frequency fluctuations in silicon nanoresonators

Authors: Marc Sansa, Eric Sage, Elizabeth C. Bullard, Marc Gély, Thomas Alava, Eric Colinet, Akshay K. Naik, Luis Guillermo Villanueva, Laurent Duraffourg, Michael L. Roukes, Guillaume Jourdan, Sébastien Hentz

Abstract: Frequency stability is key to performance of nanoresonators. This stability is thought to reach a limit with the resonator's ability to resolve thermally-induced vibrations. Although measurements and predictions of resonator stability usually disregard fluctuations in the mechanical frequency response, these fluctuations have recently attracted considerable theoretical interest. However, their exi… ▽ More Frequency stability is key to performance of nanoresonators. This stability is thought to reach a limit with the resonator's ability to resolve thermally-induced vibrations. Although measurements and predictions of resonator stability usually disregard fluctuations in the mechanical frequency response, these fluctuations have recently attracted considerable theoretical interest. However, their existence is very difficult to demonstrate experimentally. Here, through a literature review, we show that all studies of frequency stability report values several orders of magnitude larger than the limit imposed by thermomechanical noise. We studied a monocrystalline silicon nanoresonator at room temperature, and found a similar discrepancy. We propose a new method to show this was due to the presence of frequency fluctuations, of unexpected level. The fluctuations were not due to the instrumentation system, or to any other of the known sources investigated. These results challenge our current understanding of frequency fluctuations and call for a change in practices. △ Less

Submitted 15 June, 2016; v1 submitted 26 June, 2015; originally announced June 2015.

Synchronization of two anharmonic nanomechanical oscillators

Authors: M. H. Matheny, M. Grau, L. G. Villanueva, R. B. Karabalin, M. C. Cross, M. L. Roukes

Abstract: We investigate the synchronization of oscillators based on anharmonic nanoelectromechanical resonators. Our experimental implementation allows unprecedented observation and control of parameters governing the dynamics of synchronization. We find close quantitative agreement between experimental data and theory describing reactively coupled Duffing resonators with fully saturated feedback gain. In… ▽ More We investigate the synchronization of oscillators based on anharmonic nanoelectromechanical resonators. Our experimental implementation allows unprecedented observation and control of parameters governing the dynamics of synchronization. We find close quantitative agreement between experimental data and theory describing reactively coupled Duffing resonators with fully saturated feedback gain. In the synchronized state we demonstrate a significant reduction in the phase noise of the oscillators, which is key for sensor and clock applications. Our work establishes that oscillator networks constructed from nanomechanical resonators form an ideal laboratory to study synchronization given their high-quality factors, small footprint, and ease of co-integration with modern electronic signal processing technologies. △ Less

Submitted 3 May, 2013; originally announced May 2013.

Comments: 34 pages, 8 figures

Journal ref: Phys. Rev. Lett. 112, 014101 (2014)

Nonlinearity in nanomechanical cantilevers

Authors: L. G. Villanueva, R. B. Karabalin, M. H. Matheny, D. Chi, J. E. Sader, M. L. Roukes

Abstract: Euler-Bernoulli beam theory is widely used to successfully predict the linear dynamics of micro- and nano-cantilever beams. However, its capacity to characterize the nonlinear dynamics of these devices has not yet been rigorously assessed, despite its use in nanoelectromechanical systems development. In this article, we report the first highly controlled measurements of the nonlinear response of n… ▽ More Euler-Bernoulli beam theory is widely used to successfully predict the linear dynamics of micro- and nano-cantilever beams. However, its capacity to characterize the nonlinear dynamics of these devices has not yet been rigorously assessed, despite its use in nanoelectromechanical systems development. In this article, we report the first highly controlled measurements of the nonlinear response of nanomechanical cantilevers using an ultra-linear detection system. This is performed for an extensive range of devices to probe the validity of Euler-Bernoulli theory in the nonlinear regime. We find that its predictions deviate strongly from our measurements for the nonlinearity of the fundamental flexural mode, which show a systematic dependence on aspect ratio (length/width) together with random scatter. This contrasts with the second mode, which is always found to be in good agreement with theory. These findings underscore the delicate balance between inertial and geometric nonlinear effects in the fundamental mode, and strongly motivate further work to develop theories beyond the Euler-Bernoulli approximation. △ Less

Submitted 8 January, 2013; originally announced January 2013.

Comments: 24 pages, 6 figures

Optimal operating points of oscillators using nonlinear resonators

Authors: Eyal Kenig, M. C. Cross, L. G. Villanueva, R. B. Karabalin, M. H. Matheny, Ron Lifshitz, M. L. Roukes

Abstract: We demonstrate an analytical method for calculating the phase sensitivity of a class of oscillators whose phase does not affect the time evolution of the other dynamic variables. We show that such oscillators possess the possibility for complete phase noise elimination. We apply the method to a feedback oscillator which employs a high Q weakly nonlinear resonator and provide explicit parameter val… ▽ More We demonstrate an analytical method for calculating the phase sensitivity of a class of oscillators whose phase does not affect the time evolution of the other dynamic variables. We show that such oscillators possess the possibility for complete phase noise elimination. We apply the method to a feedback oscillator which employs a high Q weakly nonlinear resonator and provide explicit parameter values for which the feedback phase noise is completely eliminated and others for which there is no amplitude-phase noise conversion. We then establish an operational mode of the oscillator which optimizes its performance by diminishing the feedback noise in both quadratures, thermal noise, and quality factor fluctuations. We also study the spectrum of the oscillator and provide specific results for the case of 1/f noise sources. △ Less

Submitted 5 November, 2012; originally announced November 2012.

Journal ref: Phys. Rev. E 86 (2012) 056207

Stress-Induced Variations in the Stiffness of Micro- and Nanocantilever Beams

Authors: Rassul B. Karabalin, L. G. Villanueva, M. H. Matheny, John E. Sader, Michael L. Roukes

Abstract: The effect of surface stress on the stiffness of cantilever beams remains an outstanding problem in the physical sciences. While numerous experimental studies report significant stiffness change due to surface stress, theoretical predictions are unable to rigorously and quantitatively reconcile these observations. In this Letter, we present the first controlled measurements of stress-induced chang… ▽ More The effect of surface stress on the stiffness of cantilever beams remains an outstanding problem in the physical sciences. While numerous experimental studies report significant stiffness change due to surface stress, theoretical predictions are unable to rigorously and quantitatively reconcile these observations. In this Letter, we present the first controlled measurements of stress-induced change in cantilever stiffness with commensurate theoretical quantification. Simultaneous measurements are also performed on equivalent clamped-clamped beams. All experimental results are quantitatively and accurately predicted using elasticity theory. We also present conclusive experimental evidence for invalidity of the longstanding and unphysical axial force model, which has been widely applied to interpret measurements using cantilever beams. Our findings will be of value in the development of micro- and nanoscale resonant mechanical sensors. △ Less

Submitted 1 November, 2012; originally announced November 2012.

Comments: 12 pages, 3 figures

Journal ref: Physical Review Letters, 108, 236101 (2012)

A Nanoscale Parametric Feedback Oscillator

Authors: L. Guillermo Villanueva, Rassul B. Karabalin, Matthew H. Matheny, Eyal Kenig, Michael C. Cross, Michael L. Roukes

Abstract: We describe and demonstrate a new oscillator topology, the parametric feedback oscillator (PFO). The PFO paradigm is applicable to a wide variety of nanoscale devices, and opens the possibility of new classes of oscillators employing innovative frequency-determining elements, like such as nanoelectromechanical systems (NEMS), facilitating integration with circuitry, and reduction in cost and syste… ▽ More We describe and demonstrate a new oscillator topology, the parametric feedback oscillator (PFO). The PFO paradigm is applicable to a wide variety of nanoscale devices, and opens the possibility of new classes of oscillators employing innovative frequency-determining elements, like such as nanoelectromechanical systems (NEMS), facilitating integration with circuitry, and reduction in cost and system size reduction. We show that the PFO topology can also improve nanoscale oscillator performance by circumventing detrimental effects that are otherwise imposed by the strong device nonlinearity in this size regime. △ Less

Submitted 1 November, 2012; originally announced November 2012.

Comments: 17 pages, 3 figures

Journal ref: Nano Letters, 2011, 11 (11), pp 5054_5059

Surpassing fundamental limits of oscillators using nonlinear resonators

Authors: L. G. Villanueva, E. Kenig, R. B. Karabalin, M. H. Matheny, R. Lifshitz, M. C. Cross, M. L. Roukes

Abstract: Self-sustained oscillators are ubiquitous and essential for metrology, communications, time reference, and geolocation. In its most basic form an oscillator consists of a resonator driven on-resonance, through feedback, to create a periodic signal sustained by a static energy source. The generation of a stable frequency, the basic function of oscillators, is typically achieved by increasing the am… ▽ More Self-sustained oscillators are ubiquitous and essential for metrology, communications, time reference, and geolocation. In its most basic form an oscillator consists of a resonator driven on-resonance, through feedback, to create a periodic signal sustained by a static energy source. The generation of a stable frequency, the basic function of oscillators, is typically achieved by increasing the amplitude of motion of the resonator while remaining within its linear, harmonic, regime. Contrary to this conventional paradigm, in this Letter we show that by operating the oscillator at special points in the resonators anharmonic regime we can overcome fundamental limitations of oscillator performance due to thermodynamic noise as well as practical limitations due to noise from the sustaining circuit. We develop a comprehensive model that accounts for the major contributions to the phase noise of the nonlinear oscillator. Using a nanoelectromechanical system (NEMS)-based oscillator, we experimentally verify the existence of a special region in the operational parameter space that enables a significant reduction of the oscillators phase noise, as predicted by our model. △ Less

Submitted 30 October, 2012; originally announced October 2012.

Comments: 14 pages, 2 figures, 1 table

Journal ref: Phys. Rev. Lett. 110 (2013) 177208

A Passive Phase Noise Cancellation Element

Authors: Eyal Kenig, M. C. Cross, Ron Lifshitz, R. B. Karabalin, L. G. Villanueva, M. H. Matheny, M. L. Roukes

Abstract: We introduce a new method for reducing phase noise in oscillators, thereby improving their frequency precision. The noise reduction device consists of a pair of coupled nonlinear resonating elements that are driven parametrically by the output of a conventional oscillator at a frequency close to the sum of the linear mode frequencies. Above the threshold for parametric response, the coupled resona… ▽ More We introduce a new method for reducing phase noise in oscillators, thereby improving their frequency precision. The noise reduction device consists of a pair of coupled nonlinear resonating elements that are driven parametrically by the output of a conventional oscillator at a frequency close to the sum of the linear mode frequencies. Above the threshold for parametric response, the coupled resonators exhibit self-oscillation at an inherent frequency. We find operating points of the device for which this periodic signal is immune to frequency noise in the driving oscillator, providing a way to clean its phase noise. We present results for the effect of thermal noise to advance a broader understanding of the overall noise sensitivity and the fundamental operating limits. △ Less

Submitted 12 March, 2012; originally announced March 2012.

Journal ref: Phys. Rev. Lett. 108 (2012) 264102

Detecting and characterizing frequency fluctuations of vibrational modes

Authors: Z. A. Maizelis, M. L. Roukes, M. I. Dykman

Abstract: We show how frequency fluctuations of a vibrational mode can be separated from other sources of phase noise. The method is based on the analysis of the time dependence of the complex amplitude of forced vibrations. The moments of the complex amplitude sensitively depend on the frequency noise statistics and its power spectrum. The analysis applies to classical and to quantum vibrations. We show how frequency fluctuations of a vibrational mode can be separated from other sources of phase noise. The method is based on the analysis of the time dependence of the complex amplitude of forced vibrations. The moments of the complex amplitude sensitively depend on the frequency noise statistics and its power spectrum. The analysis applies to classical and to quantum vibrations. △ Less

Submitted 5 November, 2011; originally announced November 2011.

Journal ref: Phys. Rev. B 84, 144301 (2011)

Nonlinear Dynamics and Chaos in Two Coupled Nanomechanical Resonators

Authors: R. B. Karabalin, M. C. Cross, M. L. Roukes

Abstract: Two elastically coupled nanomechanical resonators driven independently near their resonance frequencies show intricate nonlinear dynamics. The dynamics provide a scheme for realizing a nanomechanical system with tunable frequency and nonlinear properties. For large vibration amplitudes the system develops spontaneous oscillations of amplitude modulation that also show period doubling transitions… ▽ More Two elastically coupled nanomechanical resonators driven independently near their resonance frequencies show intricate nonlinear dynamics. The dynamics provide a scheme for realizing a nanomechanical system with tunable frequency and nonlinear properties. For large vibration amplitudes the system develops spontaneous oscillations of amplitude modulation that also show period doubling transitions and chaos. The complex nonlinear dynamics are quantitatively predicted by a simple theoretical model. △ Less

Submitted 17 November, 2008; v1 submitted 6 November, 2008; originally announced November 2008.

Comments: Acknowledgment and references added. Slightly shortened to fit journal requirements

Basins of attraction of a nonlinear nanomechanical resonator

Authors: I. Kozinsky, H. W. Ch. Postma, O. Kogan, A. Husain, M. L. Roukes

Abstract: We present an experiment that systematically probes the basins of attraction of two fixed points of a nonlinear nanomechanical resonator and maps them out with high resolution. We observe a separatrix which progressively alters shape for varying drive strength and changes the relative areas of the two basins of attraction. The observed separatrix is blurred due to ambient fluctuations, including… ▽ More We present an experiment that systematically probes the basins of attraction of two fixed points of a nonlinear nanomechanical resonator and maps them out with high resolution. We observe a separatrix which progressively alters shape for varying drive strength and changes the relative areas of the two basins of attraction. The observed separatrix is blurred due to ambient fluctuations, including residual noise in the drive system, which cause uncertainty in the preparation of an initial state close to the separatrix. We find a good agreement between the experimentally mapped and theoretically calculated basins of attraction. △ Less

Submitted 13 September, 2007; originally announced September 2007.

Magnetotransport properties of strained (Ga0.95, Mn0.05)As epilayers close to the metal-insulator transition: Description using Aronov-Altshuler three-dimensional scaling theory

Authors: J. Honolka, S. Masmanidis, H. X. Tang, D. D. Awschalom, M. L. Roukes

Abstract: The magnitude of the anisotropic magnetoresistance (AMR) and the longitudinal resistance in compressively strained (Ga0.95, Mn0.05)As epilayers were measured for the first time down to temperatures as low as 30 mK. Below temperatures of 3K the conductivity decreases ~ T^1/3 over two orders of magnitude in temperature. The conductivity can be well described within the framework of a 3D scaling th… ▽ More The magnitude of the anisotropic magnetoresistance (AMR) and the longitudinal resistance in compressively strained (Ga0.95, Mn0.05)As epilayers were measured for the first time down to temperatures as low as 30 mK. Below temperatures of 3K the conductivity decreases ~ T^1/3 over two orders of magnitude in temperature. The conductivity can be well described within the framework of a 3D scaling theory of Anderson's transition in the presence of spin scattering in semiconductors. It is shown that the samples are on the metallic side but very close to the metal-insulator transition (MIT). At lowest temperatures a decrease in the AMR effect is observed, which is assigned to changes in the coupling between the remaining itinerant carriers and the local Mn 5/2-spin moments. △ Less

Submitted 1 May, 2007; originally announced May 2007.

Comments: 6 pages, 6 figures

Dissipation in Single-Crystal 3C-SiC Ultra-High Frequency Nanomechanical Resonators

Authors: X. L. Feng, C. A. Zorman, M. Mehregany, M. L. Roukes

Abstract: The energy dissipation 1/Q (where Q is the quality factor) and resonance frequency characteristics of single-crystal 3C-SiC ultrahigh frequency (UHF) nanomechanical resonators are measured, for a family of UHF resonators with resonance frequencies of 295MHz, 395MHz, 411MHz, 420MHz, 428MHz, and 482MHz. A temperature dependence of dissipation, 1/Q ~ T^(0.3) has been identified in these 3C-SiC devi… ▽ More The energy dissipation 1/Q (where Q is the quality factor) and resonance frequency characteristics of single-crystal 3C-SiC ultrahigh frequency (UHF) nanomechanical resonators are measured, for a family of UHF resonators with resonance frequencies of 295MHz, 395MHz, 411MHz, 420MHz, 428MHz, and 482MHz. A temperature dependence of dissipation, 1/Q ~ T^(0.3) has been identified in these 3C-SiC devices. Possible mechanisms that contribute to dissipation in typical doubly-clamped beam UHF resonators are analyzed. Device size and dimensional effects on the dissipation are also examined. Clam** losses are found to be particularly important in these UHF resonators. The resonance frequency decreases as the temperature is increased, and the average frequency temperature coefficient is about -45ppm/K. △ Less

Submitted 27 June, 2006; originally announced June 2006.

Comments: Solid-State Sensors, Actuators, and Microsystems Workshop Hilton Head Island, South Carolina, June 4-8, 2006 (Invited)

Nanomechanical Measurements of Magnetostriction and Magnetic Anisotropy in (Ga,Mn)As

Authors: S. C. Masmanidis, H. X. Tang, E. B. Myers, Mo Li, K. De Greve, G. Vermeulen, W. Van Roy, M. L. Roukes

Abstract: A (Ga,Mn)As nanoelectromechanical resonator is used to obtain the first direct measurement of magnetostriction in a dilute magnetic semiconductor. Field-dependent magnetoelastic stress induces shifts in resonance frequency that can be discerned with a high resolution electromechanical transduction scheme. By monitoring the field dependence, the magnetostriction and anisotropy field constants can… ▽ More A (Ga,Mn)As nanoelectromechanical resonator is used to obtain the first direct measurement of magnetostriction in a dilute magnetic semiconductor. Field-dependent magnetoelastic stress induces shifts in resonance frequency that can be discerned with a high resolution electromechanical transduction scheme. By monitoring the field dependence, the magnetostriction and anisotropy field constants can be simultaneously mapped over a wide range of temperatures. These results, when compared with theoretical predictions, appear to provide insight into a unique form of magnetoelastic behavior mediated by holes. △ Less

Submitted 9 May, 2005; originally announced May 2005.

Comments: 4 pages, 4 figures

Perturbation of magnetostatic modes observed by FMRFM

Authors: R. Urban, A. Putilin, P. E. Wigen, S. -H. Liou, M. C. Cross, P. C. Hammel, M. L. Roukes

Abstract: Magnetostatic modes of Yttrium Iron Garnet (YIG) films are investigated by ferromagnetic resonance force microscopy (FMRFM). A thin film ``probe'' magnet at the tip of a compliant cantilever introduces a local inhomogeneity in the internal field of the YIG sample. This influences the shape of the sample's magnetostatic modes, thereby measurably perturbing the strength of the force coupled to the… ▽ More Magnetostatic modes of Yttrium Iron Garnet (YIG) films are investigated by ferromagnetic resonance force microscopy (FMRFM). A thin film ``probe'' magnet at the tip of a compliant cantilever introduces a local inhomogeneity in the internal field of the YIG sample. This influences the shape of the sample's magnetostatic modes, thereby measurably perturbing the strength of the force coupled to the cantilever. We present a theoretical model that explains these observations; it shows that tip-induced variation of the internal field creates either a local ``potential barrier'' or ``potential well'' for the magnetostatic waves. The data and model together indicate that local magnetic imaging of ferromagnets is possible, even in the presence of long-range spin coupling, through the induction of localized magnetostatic modes predicted to arise from sufficiently strong tip fields. △ Less

Submitted 22 April, 2005; originally announced April 2005.

Comments: 5 pages, 4 figures, 1 table, 15 references

Comment on recent Physical Review Letter by Gaidarzhy, et al. "Evidence for quantized displacement in macroscopic nanomechanical oscillator."

Authors: K. C. Schwab, M. P. Blencowe, M. L. Roukes, A. N. Cleland, S. M. Girvin, G. J. Milburn, K. L. Ekinci

Abstract: In a recent letter, Gaidarzhy et al. claim to have observed evidence for quantized displacements of a nanomechanical oscillator. We contend that the evidence, analysis, claims, and conclusions presented are contrary to expectations from fundamentals of quantum mechanics and elasticity theory, and that the method used by the authors is unsuitable in principle to observe the quantized energy state… ▽ More In a recent letter, Gaidarzhy et al. claim to have observed evidence for quantized displacements of a nanomechanical oscillator. We contend that the evidence, analysis, claims, and conclusions presented are contrary to expectations from fundamentals of quantum mechanics and elasticity theory, and that the method used by the authors is unsuitable in principle to observe the quantized energy states of a nanomechanical structure. △ Less

Submitted 1 March, 2005; originally announced March 2005.

Anharmonic effects on a phonon number measurement of a quantum mesoscopic mechanical oscillator

Authors: D. H. Santamore, Hsi-Sheng Goan, G. J. Milburn, M. L. Roukes

Abstract: We generalize a proposal for detecting single phonon transitions in a single nanoelectromechanical system (NEMS) to include the intrinsic anharmonicity of each mechanical oscillator. In this scheme two NEMS oscillators are coupled via a term quadratic in the amplitude of oscillation for each oscillator. One NEMS oscillator is driven and strongly damped and becomes a transducer for phonon number… ▽ More We generalize a proposal for detecting single phonon transitions in a single nanoelectromechanical system (NEMS) to include the intrinsic anharmonicity of each mechanical oscillator. In this scheme two NEMS oscillators are coupled via a term quadratic in the amplitude of oscillation for each oscillator. One NEMS oscillator is driven and strongly damped and becomes a transducer for phonon number in the other measured oscillator. We derive the conditions for this measurement scheme to be quantum limited and find a condition on the size of the anharmonicity. We also derive the relation between the phase diffusion back-action noise due to number measurement and the localization time for the measured system to enter a phonon number eigenstate. We relate both these time scales to the strength of the measured signal, which is an induced current proportional to the position of the readout oscillator. △ Less

Submitted 5 October, 2004; originally announced October 2004.

Comments: 13 pages, 2 figures

Journal ref: Phys. Rev. A 70, 052105 (2004)

Electrical Transport Across an Individual Magnetic Domain Wall in (Ga,Mn)As Microdevices

Authors: Hongxing Tang, Michael L. Roukes

Abstract: Recent studies demonstrate that an individual magnetic domain wall (DW) can be trapped and reproducibly positioned within multiterminal (Ga,Mn)As microdevices. The electrical resistance obtained from such measurements is found to be measurably altered by the presence of this single entity. To elucidate these observations we develop a simple model for the electrical potential distribution along a… ▽ More Recent studies demonstrate that an individual magnetic domain wall (DW) can be trapped and reproducibly positioned within multiterminal (Ga,Mn)As microdevices. The electrical resistance obtained from such measurements is found to be measurably altered by the presence of this single entity. To elucidate these observations we develop a simple model for the electrical potential distribution along a multiterminal device in the presence of a single DW. This is employed to calculate the effect of a single DW upon the longitudinal and transverse resistance. The model provides very good agreement with experimental observations, and serves to highlight important deviations from simple theory. We show that measurements of transverse resistance along the channel permits establishing the position and the shape of the DW contained within it. An experimental scheme is developed that enables unambiguous extraction of the intrinsic DW resistivity. This permits the intrinsic contribution to be differentiated from resistivities originating from the bulk and from magnetic anisotropy - effects that are generally manifested as large backgrounds in the experiments. △ Less

Submitted 22 March, 2004; originally announced March 2004.

Comments: Submitted to Physical Review B

Ultrasensitive nanoelectromechanical mass detection

Authors: K. L. Ekinci, X. M. H. Huang, M. L. Roukes

Abstract: We describe the application of nanoelectromechanical systems (NEMS) to ultrasensitive mass detection. In these experiments, a modulated flux of atoms was adsorbed upon the surface of a 32.8 MHz NEMS resonator within an ultrahigh vacuum environment. The mass-induced resonance frequency shifts by these adsorbates were then measured to ascertain a mass sensitivity of 2.53x10^-18 g. In these initial… ▽ More We describe the application of nanoelectromechanical systems (NEMS) to ultrasensitive mass detection. In these experiments, a modulated flux of atoms was adsorbed upon the surface of a 32.8 MHz NEMS resonator within an ultrahigh vacuum environment. The mass-induced resonance frequency shifts by these adsorbates were then measured to ascertain a mass sensitivity of 2.53x10^-18 g. In these initial measurements, this sensitivity is limited by the noise in the NEMS displacement transducer; the ultimate, limits of the technique are set by fundamental phase noise processes. Our results and analysis indicate that mass sensing of individual molecules will be realizable with optimized NEMS devices. △ Less

Submitted 20 February, 2004; originally announced February 2004.

Comments: Submitted to Appl. Phys. Lett. on December 22, 2003

Nanomechanical Analog of a Laser: Amplification of Mechanical Oscillations by Stimulated Zeeman Transitions

Authors: Igor Bargatin, M. L. Roukes

Abstract: We propose a magnetomechanical device that exhibits many properties of a laser. The device is formed by a nanocantilever and dynamically polarized paramagnetic nuclei of a solid sample in a strong external magnetic field. The corresponding quantum oscillator and effective two-level systems are coupled by the magnetostatic dipole-dipole interaction between a permanent magnet on the cantilever tip… ▽ More We propose a magnetomechanical device that exhibits many properties of a laser. The device is formed by a nanocantilever and dynamically polarized paramagnetic nuclei of a solid sample in a strong external magnetic field. The corresponding quantum oscillator and effective two-level systems are coupled by the magnetostatic dipole-dipole interaction between a permanent magnet on the cantilever tip and the magnetic moments of the spins, so that the entire system is effectively described by the Jaynes-Cummings model. We consider the possibility of observing transient and cw lasing in this system, and show how these processes can be used to improve the sensitivity of magnetic resonance force microscopy. △ Less

Submitted 3 July, 2003; v1 submitted 26 April, 2003; originally announced April 2003.

Comments: REVTeX version 4: 4 pages, 2 figures. Submitted to Phys. Rev. Lett. This version incorporates suggestions of John Sidles and PRL referees

Journal ref: Phys. Rev. Lett. 91, 138302 (2003)

Giant Planar Hall Effect in Epitaxial (Ga,Mn)As Devices

Authors: H. X. Tang, R. K. Kawakami, D. D. Awschalom, M. L. Roukes

Abstract: Large Hall resistance jumps are observed in microdevices patterned from epitaxial (Ga,Mn)As layers when subjected to a swept, in-plane magnetic field. This giant planar Hall effect is four orders of magnitude greater than previously observed in metallic ferromagnets. This enables extremely sensitive measurements of the angle-dependent magnetic properties of (Ga,Mn)As. The magnetic anisotropy fie… ▽ More Large Hall resistance jumps are observed in microdevices patterned from epitaxial (Ga,Mn)As layers when subjected to a swept, in-plane magnetic field. This giant planar Hall effect is four orders of magnitude greater than previously observed in metallic ferromagnets. This enables extremely sensitive measurements of the angle-dependent magnetic properties of (Ga,Mn)As. The magnetic anisotropy fields deduced from these measurements are compared with theoretical predictions. △ Less

Submitted 12 October, 2002; v1 submitted 5 October, 2002; originally announced October 2002.

Comments: 3 figures

Magnetotransport measurements on freely suspended two-dimensional electron gases

Authors: R. H. Blick, F. G. Monzon, W. Wegscheider, M. Bichler, F. Stern, M. L. Roukes

Abstract: We present magnetotransport measurements on freely suspended two-dimensional electron gases from AlGaAs/GaAs heterostructures. The technique to realize such devices relies on a specially MBE grown GaAs/AlGaAs-heterostructure including a sacrificial layer. We fabricated simple Hall-bars as well as quantum cavities and quantum dot systems. We find well-pronounced Shubnikov-de Haas oscillations and… ▽ More We present magnetotransport measurements on freely suspended two-dimensional electron gases from AlGaAs/GaAs heterostructures. The technique to realize such devices relies on a specially MBE grown GaAs/AlGaAs-heterostructure including a sacrificial layer. We fabricated simple Hall-bars as well as quantum cavities and quantum dot systems. We find well-pronounced Shubnikov-de Haas oscillations and observe commensurability resonances, allowing characterization of the electron gas in these 100 nm thin membranes. △ Less

Submitted 22 August, 2000; originally announced August 2000.

Comments: 7 pages, 10 figures, submitted to PRB

Electrically Tunable Collective Modes in a MEMS Resonator Array

Authors: E. Buks, M. L. Roukes

Abstract: Using optical diffraction, we study the mechanical vibrations of an array of micromechanical resonators. Implementing tunable electrostatic coupling between the suspended, doubly-clamped Au beams leads to the formation of a band of collective vibrational modes within these devices. The evolution of these modes with coupling strength is clearly manifested in the optical diffraction pattern of lig… ▽ More Using optical diffraction, we study the mechanical vibrations of an array of micromechanical resonators. Implementing tunable electrostatic coupling between the suspended, doubly-clamped Au beams leads to the formation of a band of collective vibrational modes within these devices. The evolution of these modes with coupling strength is clearly manifested in the optical diffraction pattern of light transmitted through the array. The experimental results are analyzed using a simple model for one-dimensional phonons. These structures offer unique prospects for spectral analysis of complex mechanical stimuli. △ Less

Submitted 14 August, 2000; originally announced August 2000.

Comments: RevTec, 12 pages + 5 figures

Nanoelectromechanical Systems

Authors: M. L. Roukes

Abstract: Nanoelectromechanical systems, or NEMS, are MEMS scaled to submicron dimensions. In this size regime, it is possible to attain extremely high fundamental frequencies while simultaneously preserving very high mechanical responsivity (small force constants). This powerful combination of attributes translates directly into high force sensitivity, operability at ultralow power, and the ability to in… ▽ More Nanoelectromechanical systems, or NEMS, are MEMS scaled to submicron dimensions. In this size regime, it is possible to attain extremely high fundamental frequencies while simultaneously preserving very high mechanical responsivity (small force constants). This powerful combination of attributes translates directly into high force sensitivity, operability at ultralow power, and the ability to induce usable nonlinearity with quite modest control forces. In this overview I shall provide an introduction to NEMS and will outline several of their exciting initial applications. However, a stiff entry fee exists at the threshold to this new domain: new engineering is crucial to realizing the full potential of NEMS. Certain mainstays in the methodology of MEMS will, simply, not scale usefully into the regime of NEMS. The most problematic of issues are the size of the devices compared to their embedding circuitry, their extreme surface-to-volume ratios, and their unconventional "characteristic range of operation". These give rise to some of the principal current challenges in develo** NEMS. Most prominent among these are the need for: ultrasensitive, very high bandwidth displacement transducers; an unprecedented control of surface quality and adsorbates; novel modes of efficient actuation at the nanoscale, and precise, robust, and routinely reproducible new approaches to surface and bulk nanomachining. I survey each of these aspects in turn, and conclude by describing several of the exciting prospects in this new field. △ Less

Submitted 15 August, 2000; v1 submitted 11 August, 2000; originally announced August 2000.

Comments: Opening Lecture, 2000 Solid State Sensor and Actuator Workshop, Hilton Head, SC 6/4/2000, published in "Technical Digest of the 2000 Solid State Sensor and Actuator Workshop" (Transducers Research Foundation, Cleveland, OH; 2000) ISBN 0-9640024-3-4

Metastability and the Casimir Effect in Micromechanical Systems

Authors: E. Buks, M. L. Roukes

Abstract: Electrostatic and Casimir interactions limit the range of positional stability of electrostatically-actuated or capacitively-coupled mechanical devices. We investigate this range experimentally for a generic system consisting of a doubly-clamped Au suspended beam, capacitively-coupled to an adjacent stationary electrode. The mechanical properties of the beam, both in the linear and nonlinear reg… ▽ More Electrostatic and Casimir interactions limit the range of positional stability of electrostatically-actuated or capacitively-coupled mechanical devices. We investigate this range experimentally for a generic system consisting of a doubly-clamped Au suspended beam, capacitively-coupled to an adjacent stationary electrode. The mechanical properties of the beam, both in the linear and nonlinear regimes, are monitored as the attractive forces are increased to the point of instability. There "pull-in" occurs, resulting in permanent adhesion between the electrodes. We investigate, experimentally and theoretically, the position-dependent lifetimes of the free state (existing prior to pull-in). We find that the data cannot be accounted for by simple theory; the discrepancy may be reflective of internal structural instabilities within the metal electrodes. △ Less

Submitted 6 August, 2000; originally announced August 2000.

Comments: RevTex, 4 pages, 4 figures

Stiction, Adhesion Energy and the Casimir Effect in Micromechanical Systems

Authors: E. Buks, M. L. Roukes

Abstract: We measure the adhesion energy of gold using a micromachined doubly-clamped beam. The stress and stiffness of the beam are characterized by measuring the spectrum of mechanical vibrations and the deflection due to an external force. To determine the adhesion energy we induce stiction between the beam and a nearby surface by capillary forces. Subsequent analysis yields a value $γ=0.06$ J/m$^{2}$… ▽ More We measure the adhesion energy of gold using a micromachined doubly-clamped beam. The stress and stiffness of the beam are characterized by measuring the spectrum of mechanical vibrations and the deflection due to an external force. To determine the adhesion energy we induce stiction between the beam and a nearby surface by capillary forces. Subsequent analysis yields a value $γ=0.06$ J/m$^{2}$ that is a factor of approximately six smaller than predicted by idealized theory. This discrepancy may be resolved with revised models that include surface roughness and the effect of adsorbed monolayers intervening between the contacting surfaces in these mesoscopic structures. △ Less

Submitted 4 August, 2000; v1 submitted 3 August, 2000; originally announced August 2000.

Comments: RevTex, 4 pages, 4 eps figures

Thermoelastic Dam** in Micro- and Nano-Mechanical Systems

Authors: Ron Lifshitz, M. L. Roukes

Abstract: The importance of thermoelastic dam** as a fundamental dissipation mechanism for small-scale mechanical resonators is evaluated in light of recent efforts to design high-Q micrometer- and nanometer-scale electro-mechanical systems (MEMS and NEMS). The equations of linear thermoelasticity are used to give a simple derivation for thermoelastic dam** of small flexural vibrations in thin beams.… ▽ More The importance of thermoelastic dam** as a fundamental dissipation mechanism for small-scale mechanical resonators is evaluated in light of recent efforts to design high-Q micrometer- and nanometer-scale electro-mechanical systems (MEMS and NEMS). The equations of linear thermoelasticity are used to give a simple derivation for thermoelastic dam** of small flexural vibrations in thin beams. It is shown that Zener's well-known approximation by a Lorentzian with a single thermal relaxation time slightly deviates from the exact expression. △ Less

Submitted 17 September, 1999; originally announced September 1999.

Comments: 10 pages. Submitted to Phys. Rev. B

Journal ref: Phys. Rev. B 61, 5600 (2000).

Spin Injection in a Ballistic Two-Dimensional Electron Gas

Authors: H. X. Tang, F. G. Monzon, Ron Lifshitz, M. C. Cross, M. L. Roukes

Abstract: We explore electrically injected, spin polarized transport in a ballistic two-dimensional electron gas. We augment the Buettiker-Landauer picture with a simple, but realistic model for spin-selective contacts to describe multimode reservoir-to-reservoir transport of ballistic spin 1/2 particles. Clear and unambiguous signatures of spin transport are established in this regime, for the simplest m… ▽ More We explore electrically injected, spin polarized transport in a ballistic two-dimensional electron gas. We augment the Buettiker-Landauer picture with a simple, but realistic model for spin-selective contacts to describe multimode reservoir-to-reservoir transport of ballistic spin 1/2 particles. Clear and unambiguous signatures of spin transport are established in this regime, for the simplest measurement configuration that demonstrates them directly. These new effects originate from spin precession of ballistic carriers; they exhibit strong dependence upon device geometry and vanish in the diffusive limit. Our results have important implications for prospective ``spin transistor'' devices. △ Less

Submitted 28 July, 1999; originally announced July 1999.

Comments: Submitted to Phys. Rev. Lett

Journal ref: Phys. Rev. B 61 (2000) 4437-4440.

Yoctocalorimetry: phonon counting in nanostructures

Authors: M. L. Roukes

Abstract: It appears feasible with nanostructures to perform calorimetry at the level of individual thermal phonons. Here I outline an approach employing monocrystalline mesoscopic insulators, which can now be patterned from semiconductor heterostructures into complex geometries with full, three- dimensional relief. Successive application of these techniques also enables definition of integrated nanoscale… ▽ More It appears feasible with nanostructures to perform calorimetry at the level of individual thermal phonons. Here I outline an approach employing monocrystalline mesoscopic insulators, which can now be patterned from semiconductor heterostructures into complex geometries with full, three- dimensional relief. Successive application of these techniques also enables definition of integrated nanoscale thermal transducers; coupling these to a dc SQUID readout yields the requisite energy sensitivity and temporal resolution with minimal back action. The prospect of phonon counting opens intriguing experimental possibilities with analogies in quantum optics. These include fluctuation-based phonon spectroscopy, phonon shot noise in the energy relaxation of nanoscale systems, and quantum statistical phenomena such as phonon bunching and anticorrelated electron-phonon exchange. △ Less

Submitted 17 November, 1998; v1 submitted 17 November, 1998; originally announced November 1998.

Comments: 27 pages, 8 figures

Ferromagnetic resonance force microscopy on microscopic cobalt single layer films

Authors: Z. Zhang, P. C. Hammel, M. Midzor, M. L. Roukes, J. R. Childress

Abstract: We report mechanical detection of ferromagnetic resonance signals from microscopic Co single layer thin films using a magnetic resonance force microscope (MRFM). Variations in the magnetic anisotropy field and the inhomogeneity of were clearly observed in the FMR spectra of microscopic Co thin films 500 and 1000 angstrom thick and 40 X 200 micron^2 in lateral extent. This demonstrates the import… ▽ More We report mechanical detection of ferromagnetic resonance signals from microscopic Co single layer thin films using a magnetic resonance force microscope (MRFM). Variations in the magnetic anisotropy field and the inhomogeneity of were clearly observed in the FMR spectra of microscopic Co thin films 500 and 1000 angstrom thick and 40 X 200 micron^2 in lateral extent. This demonstrates the important potential that MRFM detection of FMR holds for microscopic characterization of spatial distribution of magnetic properties in magnetic layered materials and devices. △ Less

Submitted 28 August, 1998; originally announced August 1998.

Comments: 4 pages, 2 figures, RevTex. To be published in Applied Physics Letters, October 5, 1998

Report number: LA-UR-97-5168

Heat Transport in Mesoscopic Systems

Authors: D. E. Angelescu, M. C. Cross, M. L. Roukes

Abstract: Phonon heat transport in mesoscopic systems is investigated using methods analogous to the Landauer description of electrical conductance. A "universal heat conductance" expression that depends on the properties of the conducting pathway only through the mode cutoff frequencies is derived. Corrections due to reflections at the junction between the thermal body and the conducting bridge are found… ▽ More Phonon heat transport in mesoscopic systems is investigated using methods analogous to the Landauer description of electrical conductance. A "universal heat conductance" expression that depends on the properties of the conducting pathway only through the mode cutoff frequencies is derived. Corrections due to reflections at the junction between the thermal body and the conducting bridge are found to be small except at very low temperatures where only the lowest few bridge modes are excited. Various non-equilibrium phonon distributions are studied: a narrow band distribution leads to clear steps in the cooling curve, analogous to the quantized resistance values in narrow wires, but a thermal distribution is too broad to show such features. △ Less

Submitted 23 January, 1998; originally announced January 1998.

Comments: To be published in Superlattices and Microstructures, special issue in honor of Rolf Landauer, March 1988

Report number: CMP-001

Perturbation of Tunneling Processes by Mechanical Degrees of Freedom in Mesoscopic Junctions

Authors: N. F. Schwabe, A. N. Cleland, M. C. Cross, M. L. Roukes

Abstract: We investigate the perturbation in the tunneling current caused by non-adiabatic mechanical motion in a mesoscopic tunnel junction. A theory introduced by Caroli et al. \cite{bi1,bi2,bi3} is used to evaluate second order self-energy corrections for this non-equilibrium situation lacking translational invariance. Inelastic signatures of the mechanical degrees of freedom are found in the current-v… ▽ More We investigate the perturbation in the tunneling current caused by non-adiabatic mechanical motion in a mesoscopic tunnel junction. A theory introduced by Caroli et al. \cite{bi1,bi2,bi3} is used to evaluate second order self-energy corrections for this non-equilibrium situation lacking translational invariance. Inelastic signatures of the mechanical degrees of freedom are found in the current-voltage $I(V)$ characteristics. These give rise to sharp features in the derivative spectrum, $d^2I/dV^2$. △ Less

Submitted 31 May, 1995; originally announced May 1995.

Comments: 22 pages LaTeX + 3 uuencoded PS pictures