-
Spin-to-charge conversion by spin pum** in sputtered polycrystalline Bi$_x$Se$_{1-x}$
Authors:
Isabel C Arango,
Alberto Anadón,
Silvestre Novoa,
Van Tuong Pham,
Won Young Choi,
Junior Alegre,
Laurent Badie,
Andrey Chuvilin,
Sébastien Petit-Watelot,
Luis E Hueso,
Fèlix Casanova,
Juan-Carlos Rojas-Sánchez
Abstract:
Topological materials are of high interest due to the promise to obtain low power and fast memory devices based on efficient spin-orbit torque switching or spin-orbit magnetic state read-out. In particular, sputtered polycrystalline Bi$_x$Se$_{1-x}$ is one of the materials with more potential for this purpose since it is relatively easy to fabricate and has been reported to have a very high spin H…
▽ More
Topological materials are of high interest due to the promise to obtain low power and fast memory devices based on efficient spin-orbit torque switching or spin-orbit magnetic state read-out. In particular, sputtered polycrystalline Bi$_x$Se$_{1-x}$ is one of the materials with more potential for this purpose since it is relatively easy to fabricate and has been reported to have a very high spin Hall angle. We study the spin-to-charge conversion in Bi$_x$Se$_{1-x}$ using the spin pum** technique coming from the ferromagnetic resonance in a contiguous permalloy thin film. We put a special emphasis on the interfacial properties of the system. Our results show that the spin Hall angle of Bi$_x$Se$_{1-x}$ has an opposite sign to the one of Pt. The charge current arising from the spin-to-charge conversion is, in contrast, lower than Pt by more than one order of magnitude. We ascribe this to the interdiffusion of Bi$_x$Se$_{1-x}$ and permalloy and the changes in chemical composition produced by this effect, which is an intrinsic characteristic of the system and is not considered in many other studies.
△ Less
Submitted 16 June, 2023; v1 submitted 24 December, 2022;
originally announced December 2022.
-
Notch Fracture predictions using the Phase Field method for Ti-6Al-4V produced by Selective Laser Melting after different post-processing conditions
Authors:
A. Díaz,
J. M. Alegre,
I. I. Cuesta,
E. Martínez-Pañeda,
Z. Zhang
Abstract:
Ti-6Al-4V is a titanium alloy with excellent properties for lightweight applications and its production through Additive Manufacturing processes is attractive for different industrial sectors. In this work, the influence of mechanical properties on the notch fracture resistance of Ti-6Al-4V produced by Selective Laser Melting is numerically investigated. Literature data is used to inform material…
▽ More
Ti-6Al-4V is a titanium alloy with excellent properties for lightweight applications and its production through Additive Manufacturing processes is attractive for different industrial sectors. In this work, the influence of mechanical properties on the notch fracture resistance of Ti-6Al-4V produced by Selective Laser Melting is numerically investigated. Literature data is used to inform material behaviour. The as-built brittle behaviour is compared to the enhanced ductile response after heat treatment (HT) and hot isostatic pressing (HIP) post-processes. A Phase Field framework is adopted to capture damage nucleation and propagation from two different notch geometries and a discussion on the influence of fracture energy and the characteristic length is carried out. In addition, the influence of oxygen uptake is analysed by reproducing non-inert atmospheres during HT and HIP, showing that oxygen shifts fracture to brittle failures due to the formation of an alpha case layer, especially for the V-notch geometry. Results show that a pure elastic behaviour can be assumed for the as-built SLM condition, whereas elastic-plastic phenomena must be modelled for specimens subjected to heat treatment or hot isostatic pressing. The present brittle Phase Field framework coupled with an elastic-plastic constitutive analysis is demonstrated to be a robust prediction tool for notch fracture after different post-processing routes.
△ Less
Submitted 16 September, 2022;
originally announced September 2022.
-
Thermal spin current generation in the multifunctional ferrimagnet Ga$_{0.6}$Fe$_{1.4}$O$_{3}$
Authors:
Alberto Anadón,
Elodie Martin,
Suvidyakumar Homkar,
Benjamin Meunier,
Maxime Verges,
Heloise Damas,
Junior Alegre,
Christophe Lefevre,
Francois Roulland,
Carsten Dubs,
Morris Lindner,
Ludovic Pasquier,
Olivier Copie,
Karine Dumesnil,
Rafael Ramos,
Daniele Preziosi,
Sébastien Petit-Watelot,
Nathalie Viart,
Juan-Carlos Rojas-Sánchez
Abstract:
In recent years, multifunctional materials have attracted increasing interest for magnetic memories and energy harvesting applications. Magnetic insulating materials are of special interest for this purpose, since they allow the design of more efficient devices due to the lower Joule heat losses. In this context, Ga$_{0.6}$Fe$_{1.4}$O$_3$ (GFO) is a good candidate for spintronics applications, sin…
▽ More
In recent years, multifunctional materials have attracted increasing interest for magnetic memories and energy harvesting applications. Magnetic insulating materials are of special interest for this purpose, since they allow the design of more efficient devices due to the lower Joule heat losses. In this context, Ga$_{0.6}$Fe$_{1.4}$O$_3$ (GFO) is a good candidate for spintronics applications, since it can exhibit multiferroicity and presents a spin Hall magnetoresistance similar to the one observed in a yttrium iron garnet (YIG)/Pt bilayer. Here, we explore GFO utilizing thermo-spin measurements in an on-chip approach. By carefully considering the geometry of our thermo-spin devices we are able to quantify the spin Seebeck effect and the spin current generation in a GFO/Pt bilayer, obtaining a value comparable to that of YIG/Pt. This further confirms the promises of an efficient spin current generation with the possibility of an electric-field manipulation of the magnetic properties of the system in an insulating ferrimagnetic material.
△ Less
Submitted 3 July, 2022; v1 submitted 27 June, 2022;
originally announced June 2022.
-
Simulation of hydrogen permeation through pure iron for trap** and surface phenomena characterisation
Authors:
A. Díaz,
A. Zafra,
E. Martínez-Pañeda,
J. M. Alegre,
J. Belzunce,
I. I. Cuesta
Abstract:
There is a need for numerical models capable of predicting local accumulation of hydrogen near stress concentrators and crack tips to prevent and mitigate hydrogen assisted fracture in steels. The experimental characterisation of trap** parameters in metals, which is required for an accurate simulation of hydrogen transport, is usually performed through the electropermeation test. In order to st…
▽ More
There is a need for numerical models capable of predicting local accumulation of hydrogen near stress concentrators and crack tips to prevent and mitigate hydrogen assisted fracture in steels. The experimental characterisation of trap** parameters in metals, which is required for an accurate simulation of hydrogen transport, is usually performed through the electropermeation test. In order to study grain size influence and grain boundary trap** during permeation, two modelling approaches are explored; a 1D Finite Element model including trap density and binding energy as input parameters and a polycrystalline model based on the assignment of a lower diffusivity and solubility to the grain boundaries. Samples of pure iron after two different heat treatments - 950C for 40 minutes and 1100C for 5 minutes - are tested applying three consecutive rising permeation steps and three decaying steps. Experimental results show that the finer grain microstructure promotes a diffusion delay due to grain boundary trap**. The usual methodology for the determination of trap densities and binding energies is revisited in which the limiting diluted and saturated cases are considered. To this purpose, apparent diffusivities are fitted including also the influence of boundary conditions and comparing results provided by the constant concentration with the constant flux assumption. Grain boundaries are characterised for pure iron with a binding energy between 37.8 and 39.9 kJ/mol and a low trap density but it is numerically demonstrated that saturated or diluted assumptions are not always verified, and a univocal determination of trap** parameters requires a broader range of charging conditions for permeation. The relationship between surface parameters, i.e. charging current, recombination current and surface concentrations, is also studied.
△ Less
Submitted 26 October, 2020;
originally announced October 2020.
-
Analysis of hydrogen permeation tests considering two different modelling approaches for grain boundary trap** in iron
Authors:
A. Díaz,
I. I. Cuesta,
E. Martínez-Pañeda,
J. M. Alegre
Abstract:
The electrochemical permeation test is one of the most used methods for characterising hydrogen diffusion in metals. The flux of hydrogen atoms registered in the oxidation cell might be fitted to obtain apparent diffusivities. The magnitude of this coefficient has a decisive influence on the kinetics of fracture or fatigue phenomena assisted by hydrogen and depends largely on hydrogen retention in…
▽ More
The electrochemical permeation test is one of the most used methods for characterising hydrogen diffusion in metals. The flux of hydrogen atoms registered in the oxidation cell might be fitted to obtain apparent diffusivities. The magnitude of this coefficient has a decisive influence on the kinetics of fracture or fatigue phenomena assisted by hydrogen and depends largely on hydrogen retention in microstructural traps. In order to improve the numerical fitting of diffusion coefficients, a permeation test has been reproduced using FEM simulations considering two approaches: a continuum 1D model in which the trap density, binding energy and the input lattice concentrations are critical variables and a polycrystalline model where trap** at grain boundaries is simulated explicitly including a segregation factor and a diffusion coefficient different from that of the interior of the grain. Results show that the continuum model captures trap** delay, but it should be modified to model the trap** influence on the steady state flux. Permeation behaviour might be classified according to different regimes depending on deviation from Fickian diffusion. Polycrystalline synthetic permeation shows a strong influence of segregation on output flux magnitude. This approach is able to simulate also the short-circuit diffusion phenomenon. The comparison between different grain sizes and grain boundary thicknesses by means of the fitted apparent diffusivity shows the relationships between the registered flux and the characteristic parameters of traps.
△ Less
Submitted 5 December, 2019;
originally announced December 2019.
-
Cold Isostatic Pressing to Improve the Mechanical Performance of Additively Manufactured Metallic Components
Authors:
Isidoro Iván Cuesta,
Emilio Martínez-Pañeda,
Andrés Díaz,
Jesús Manuel Alegre
Abstract:
Additive manufacturing is becoming a technique with great prospects for the production of components with new designs or shapes that are difficult to obtain by conventional manufacturing methods. One of the most promising techniques for printing metallic components is binder jetting, due to its time efficiency and its ability to generate complex parts. In this process, a liquid binding agent is se…
▽ More
Additive manufacturing is becoming a technique with great prospects for the production of components with new designs or shapes that are difficult to obtain by conventional manufacturing methods. One of the most promising techniques for printing metallic components is binder jetting, due to its time efficiency and its ability to generate complex parts. In this process, a liquid binding agent is selectively deposited to adhere the powder particles of the printing material. Once the metallic piece is generated, it undergoes a subsequent process of curing and sintering to increase its density (hot isostatic pressing). In this work, we propose subjecting the manufactured component to an additional post-processing treatment involving the application of a high hydrostatic pressure (5000 bar) at room temperature. This post-processing technique, so-called cold isostatic pressing (CIP), is shown to increase the yield load and the maximum carrying capacity of an additively manufactured AISI 316L stainless steel. The mechanical properties, with and without CIP processing, are estimated by means of the small punch test, a suitable experimental technique to assess the mechanical response of small samples. In addition, we investigate the porosity and microstructure of the material according to the orientations of layer deposition during the manufacturing process. Our observations reveal a homogeneous distribution independent of these orientations, evidencing thus an isotropic behaviour of the material.
△ Less
Submitted 8 August, 2019;
originally announced August 2019.
-
The Essential Work of Fracture Parameters for 3D printed polymer sheets
Authors:
I. I. Cuesta,
E. Martinez-Pañeda,
A. Díaz,
J. M. Alegre
Abstract:
Additive manufacturing is becoming increasingly popular in academia and industry. Accordingly, there has been a growing interest in characterizing 3D printed samples to determine their structural integrity behaviour. We employ the Essential Work of Fracture (EWF) to investigate the mechanical response of polymer sheets obtained through additive manufacturing. Our goal is twofold; first, we aim at…
▽ More
Additive manufacturing is becoming increasingly popular in academia and industry. Accordingly, there has been a growing interest in characterizing 3D printed samples to determine their structural integrity behaviour. We employ the Essential Work of Fracture (EWF) to investigate the mechanical response of polymer sheets obtained through additive manufacturing. Our goal is twofold; first, we aim at gaining insight into the role of fibre reinforcement on the fracture resistance of additively manufactured polymer sheets. Deeply double-edge notched tensile (DDEN-T) tests are conducted on four different polymers: Onyx, a crystalline, nylon-reinforced polymer, and three standard polymers used in additive manufacturing - PLA, PP and ABS. Results show that fibre-reinforcement translates into a notable increase in fracture resistance, with the fracture energy of Onyx being an order of magnitude higher than that reported for non-reinforced polymers. On the other hand, we propose the use of a miniature test specimen, the deeply double-edge notched small punch specimens (DDEN-SP), to characterize the mechanical response using a limited amount of material. The results obtained exhibit good alignment with the DDEN-T data, suggesting the suitability of the DDEN-SP test for measuring fracture properties of additively manufactured polymers in a cost-effective manner.
△ Less
Submitted 27 June, 2019;
originally announced June 2019.
-
Pre-notched dog bone small punch specimens for the estimation of fracture properties
Authors:
I. I. Cuesta,
A. Willig,
A. Díaz,
E. Martínez-Pañeda,
J. M. Alegre
Abstract:
In recent years, the pre-notched or pre-cracked small punch test (P-SPT) has been successfully used to estimate the fracture properties of metallic materials for cases in which there is not sufficient material to identify these properties from standard tests, such as CT or SENB specimens. The P-SPT basically consists of deforming a pre-notched miniature specimen, whose edges are firmly gripped by…
▽ More
In recent years, the pre-notched or pre-cracked small punch test (P-SPT) has been successfully used to estimate the fracture properties of metallic materials for cases in which there is not sufficient material to identify these properties from standard tests, such as CT or SENB specimens. The P-SPT basically consists of deforming a pre-notched miniature specimen, whose edges are firmly gripped by a die, using a high strength punch. The novelty of this paper lies in the estimation of fracture properties using dog-bone-shaped specimens with different confinement levels. With these specimens, three confinement variations have been studied. The results obtained enable the establishment of a variation of fracture properties depending on the level of confinement of each miniature specimen and selection of the most appropriate confinement for this goal.
△ Less
Submitted 22 October, 2018;
originally announced October 2018.
-
Damage modeling in Small Punch Test specimens
Authors:
Emilio Martínez-Pañeda,
Ivan I. Cuesta,
Ines Peñuelas,
Andres Díaz,
Jesus M. Alegre
Abstract:
Ductile damage modeling within the Small Punch Test (SPT) is extensively investigated. The capabilities of the SPT to reliably estimate fracture and damage properties are thoroughly discussed and emphasis is placed on the use of notched specimens. First, different notch profiles are analyzed and constraint conditions quantified. The role of the notch shape is comprehensively examined from both tri…
▽ More
Ductile damage modeling within the Small Punch Test (SPT) is extensively investigated. The capabilities of the SPT to reliably estimate fracture and damage properties are thoroughly discussed and emphasis is placed on the use of notched specimens. First, different notch profiles are analyzed and constraint conditions quantified. The role of the notch shape is comprehensively examined from both triaxiality and notch fabrication perspectives. Afterwards, a methodology is presented to extract the micromechanical-based ductile damage parameters from the load-displacement curve of notched SPT samples. Furthermore, Gurson-Tvergaard-Needleman model predictions from a top-down approach are employed to gain insight into the mechanisms governing crack initiation and subsequent propagation in small punch experiments. An accurate assessment of micromechanical toughness parameters from the SPT is of tremendous relevance when little material is available.
△ Less
Submitted 18 November, 2017;
originally announced November 2017.
