Showing 1–14 of 14 results for author: Short, A

Euclid. II. The VIS Instrument

Authors: Euclid Collaboration, M. Cropper, A. Al-Bahlawan, J. Amiaux, S. Awan, R. Azzollini, K. Benson, M. Berthe, J. Boucher, E. Bozzo, C. Brockley-Blatt, G. P. Candini, C. Cara, R. A. Chaudery, R. E. Cole, P. Danto, J. Denniston, A. M. Di Giorgio, B. Dryer, J. Endicott, J. -P. Dubois, M. Farina, E. Galli, L. Genolet, J. P. D. Gow , et al. (403 additional authors not shown)

Abstract: This paper presents the specification, design, and development of the Visible Camera (VIS) on the ESA Euclid mission. VIS is a large optical-band imager with a field of view of 0.54 deg^2 sampled at 0.1" with an array of 609 Megapixels and spatial resolution of 0.18". It will be used to survey approximately 14,000 deg^2 of extragalactic sky to measure the distortion of galaxies in the redshift ran… ▽ More This paper presents the specification, design, and development of the Visible Camera (VIS) on the ESA Euclid mission. VIS is a large optical-band imager with a field of view of 0.54 deg^2 sampled at 0.1" with an array of 609 Megapixels and spatial resolution of 0.18". It will be used to survey approximately 14,000 deg^2 of extragalactic sky to measure the distortion of galaxies in the redshift range z=0.1-1.5 resulting from weak gravitational lensing, one of the two principal cosmology probes of Euclid. With photometric redshifts, the distribution of dark matter can be mapped in three dimensions, and, from how this has changed with look-back time, the nature of dark energy and theories of gravity can be constrained. The entire VIS focal plane will be transmitted to provide the largest images of the Universe from space to date, reaching m_AB>24.5 with S/N >10 in a single broad I_E~(r+i+z) band over a six year survey. The particularly challenging aspects of the instrument are the control and calibration of observational biases, which lead to stringent performance requirements and calibration regimes. With its combination of spatial resolution, calibration knowledge, depth, and area covering most of the extra-Galactic sky, VIS will also provide a legacy data set for many other fields. This paper discusses the rationale behind the VIS concept and describes the instrument design and development before reporting the pre-launch performance derived from ground calibrations and brief results from the in-orbit commissioning. VIS should reach fainter than m_AB=25 with S/N>10 for galaxies of full-width half-maximum of 0.3" in a 1.3" diameter aperture over the Wide Survey, and m_AB>26.4 for a Deep Survey that will cover more than 50 deg^2. The paper also describes how VIS works with the other Euclid components of survey, telescope, and science data processing to extract the cosmological information. △ Less

Submitted 22 May, 2024; originally announced May 2024.

Comments: Paper submitted as part of the A&A special issue `Euclid on Sky', which contains Euclid key reference papers and first results from the Euclid Early Release Observations

Euclid. I. Overview of the Euclid mission

Authors: Euclid Collaboration, Y. Mellier, Abdurro'uf, J. A. Acevedo Barroso, A. Achúcarro, J. Adamek, R. Adam, G. E. Addison, N. Aghanim, M. Aguena, V. Ajani, Y. Akrami, A. Al-Bahlawan, A. Alavi, I. S. Albuquerque, G. Alestas, G. Alguero, A. Allaoui, S. W. Allen, V. Allevato, A. V. Alonso-Tetilla, B. Altieri, A. Alvarez-Candal, A. Amara, L. Amendola , et al. (1086 additional authors not shown)

Abstract: The current standard model of cosmology successfully describes a variety of measurements, but the nature of its main ingredients, dark matter and dark energy, remains unknown. Euclid is a medium-class mission in the Cosmic Vision 2015-2025 programme of the European Space Agency (ESA) that will provide high-resolution optical imaging, as well as near-infrared imaging and spectroscopy, over about 14… ▽ More The current standard model of cosmology successfully describes a variety of measurements, but the nature of its main ingredients, dark matter and dark energy, remains unknown. Euclid is a medium-class mission in the Cosmic Vision 2015-2025 programme of the European Space Agency (ESA) that will provide high-resolution optical imaging, as well as near-infrared imaging and spectroscopy, over about 14,000 deg^2 of extragalactic sky. In addition to accurate weak lensing and clustering measurements that probe structure formation over half of the age of the Universe, its primary probes for cosmology, these exquisite data will enable a wide range of science. This paper provides a high-level overview of the mission, summarising the survey characteristics, the various data-processing steps, and data products. We also highlight the main science objectives and expected performance. △ Less

Submitted 22 May, 2024; originally announced May 2024.

Comments: Paper submitted as part of the A&A special issue`Euclid on Sky'

Euclid preparation. XXIX. Water ice in spacecraft part I: The physics of ice formation and contamination

Authors: Euclid Collaboration, M. Schirmer, K. Thürmer, B. Bras, M. Cropper, J. Martin-Fleitas, Y. Goueffon, R. Kohley, A. Mora, M. Portaluppi, G. D. Racca, A. D. Short, S. Szmolka, L. M. Gaspar Venancio, M. Altmann, Z. Balog, U. Bastian, M. Biermann, D. Busonero, C. Fabricius, F. Grupp, C. Jordi, W. Löffler, A. Sagristà Sellés, N. Aghanim , et al. (196 additional authors not shown)

Abstract: Molecular contamination is a well-known problem in space flight. Water is the most common contaminant and alters numerous properties of a cryogenic optical system. Too much ice means that Euclid's calibration requirements and science goals cannot be met. Euclid must then be thermally decontaminated, a long and risky process. We need to understand how iced optics affect the data and when a decontam… ▽ More Molecular contamination is a well-known problem in space flight. Water is the most common contaminant and alters numerous properties of a cryogenic optical system. Too much ice means that Euclid's calibration requirements and science goals cannot be met. Euclid must then be thermally decontaminated, a long and risky process. We need to understand how iced optics affect the data and when a decontamination is required. This is essential to build adequate calibration and survey plans, yet a comprehensive analysis in the context of an astrophysical space survey has not been done before. In this paper we look at other spacecraft with well-documented outgassing records, and we review the formation of thin ice films. A mix of amorphous and crystalline ices is expected for Euclid. Their surface topography depends on the competing energetic needs of the substrate-water and the water-water interfaces, and is hard to predict with current theories. We illustrate that with scanning-tunnelling and atomic-force microscope images. Industrial tools exist to estimate contamination, and we must understand their uncertainties. We find considerable knowledge errors on the diffusion and sublimation coefficients, limiting the accuracy of these tools. We developed a water transport model to compute contamination rates in Euclid, and find general agreement with industry estimates. Tests of the Euclid flight hardware in space simulators did not pick up contamination signals; our in-flight calibrations observations will be much more sensitive. We must understand the link between the amount of ice on the optics and its effect on Euclid's data. Little research is available about this link, possibly because other spacecraft can decontaminate easily, quenching the need for a deeper understanding. In our second paper we quantify the various effects of iced optics on spectrophotometric data. △ Less

Submitted 23 May, 2023; v1 submitted 17 May, 2023; originally announced May 2023.

Comments: 35 pages, 22 figures, A&A in press. Changes to previous version: language edits, added Z. Bolag as author in the arxiv PDF (was listed in the ASCII author list and in the journal PDF, but not in the arxiv PDF). This version is identical to the journal version

Journal ref: A&A 675, A142 (2023)

Gaia Data Release 1. Testing the parallaxes with local Cepheids and RR Lyrae stars

Authors: Gaia Collaboration, G. Clementini, L. Eyer, V. Ripepi, M. Marconi, T. Muraveva, A. Garofalo, L. M. Sarro, M. Palmer, X. Luri, R. Molinaro, L. Rimoldini, L. Szabados, I. Musella, R. I. Anderson, T. Prusti, J. H. J. de Bruijne, A. G. A. Brown, A. Vallenari, C. Babusiaux, C. A. L. Bailer-Jones, U. Bastian, M. Biermann, D. W. Evans, F. Jansen , et al. (566 additional authors not shown)

Abstract: Parallaxes for 331 classical Cepheids, 31 Type II Cepheids and 364 RR Lyrae stars in common between Gaia and the Hipparcos and Tycho-2 catalogues are published in Gaia Data Release 1 (DR1) as part of the Tycho-Gaia Astrometric Solution (TGAS). In order to test these first parallax measurements of the primary standard candles of the cosmological distance ladder, that involve astrometry collected by… ▽ More Parallaxes for 331 classical Cepheids, 31 Type II Cepheids and 364 RR Lyrae stars in common between Gaia and the Hipparcos and Tycho-2 catalogues are published in Gaia Data Release 1 (DR1) as part of the Tycho-Gaia Astrometric Solution (TGAS). In order to test these first parallax measurements of the primary standard candles of the cosmological distance ladder, that involve astrometry collected by Gaia during the initial 14 months of science operation, we compared them with literature estimates and derived new period-luminosity ($PL$), period-Wesenheit ($PW$) relations for classical and Type II Cepheids and infrared $PL$, $PL$-metallicity ($PLZ$) and optical luminosity-metallicity ($M_V$-[Fe/H]) relations for the RR Lyrae stars, with zero points based on TGAS. The new relations were computed using multi-band ($V,I,J,K_{\mathrm{s}},W_{1}$) photometry and spectroscopic metal abundances available in the literature, and applying three alternative approaches: (i) by linear least squares fitting the absolute magnitudes inferred from direct transformation of the TGAS parallaxes, (ii) by adopting astrometric-based luminosities, and (iii) using a Bayesian fitting approach. TGAS parallaxes bring a significant added value to the previous Hipparcos estimates. The relations presented in this paper represent first Gaia-calibrated relations and form a "work-in-progress" milestone report in the wait for Gaia-only parallaxes of which a first solution will become available with Gaia's Data Release 2 (DR2) in 2018. △ Less

Submitted 1 May, 2017; originally announced May 2017.

Comments: 29 pages, 25 figures. Accepted for publication by A&A

Journal ref: A&A 605, A79 (2017)

Gaia Data Release 1. Open cluster astrometry: performance, limitations, and future prospects

Authors: Gaia Collaboration, F. van Leeuwen, A. Vallenari, C. Jordi, L. Lindegren, U. Bastian, T. Prusti, J. H. J. de Bruijne, A. G. A. Brown, C. Babusiaux, C. A. L. Bailer-Jones, M. Biermann, D. W. Evans, L. Eyer, F. Jansen, S. A. Klioner, U. Lammers, X. Luri, F. Mignard, C. Panem, D. Pourbaix, S. Randich, P. Sartoretti, H. I. Siddiqui, C. Soubiran , et al. (567 additional authors not shown)

Abstract: Context. The first Gaia Data Release contains the Tycho-Gaia Astrometric Solution (TGAS). This is a subset of about 2 million stars for which, besides the position and photometry, the proper motion and parallax are calculated using Hipparcos and Tycho-2 positions in 1991.25 as prior information. Aims. We investigate the scientific potential and limitations of the TGAS component by means of the ast… ▽ More Context. The first Gaia Data Release contains the Tycho-Gaia Astrometric Solution (TGAS). This is a subset of about 2 million stars for which, besides the position and photometry, the proper motion and parallax are calculated using Hipparcos and Tycho-2 positions in 1991.25 as prior information. Aims. We investigate the scientific potential and limitations of the TGAS component by means of the astrometric data for open clusters. Methods. Mean cluster parallax and proper motion values are derived taking into account the error correlations within the astrometric solutions for individual stars, an estimate of the internal velocity dispersion in the cluster, and, where relevant, the effects of the depth of the cluster along the line of sight. Internal consistency of the TGAS data is assessed. Results. Values given for standard uncertainties are still inaccurate and may lead to unrealistic unit-weight standard deviations of least squares solutions for cluster parameters. Reconstructed mean cluster parallax and proper motion values are generally in very good agreement with earlier Hipparcos-based determination, although the Gaia mean parallax for the Pleiades is a significant exception. We have no current explanation for that discrepancy. Most clusters are observed to extend to nearly 15 pc from the cluster centre, and it will be up to future Gaia releases to establish whether those potential cluster-member stars are still dynamically bound to the clusters. Conclusions. The Gaia DR1 provides the means to examine open clusters far beyond their more easily visible cores, and can provide membership assessments based on proper motions and parallaxes. A combined HR diagram shows the same features as observed before using the Hipparcos data, with clearly increased luminosities for older A and F dwarfs. △ Less

Submitted 3 March, 2017; originally announced March 2017.

Comments: Accepted for publication by A&A. 21 pages main text plus 46 pages appendices. 34 figures main text, 38 figures appendices. 8 table in main text, 19 tables in appendices

Journal ref: A&A 601, A19 (2017)

The Euclid mission design

Authors: Giuseppe D Racca, Rene Laureijs, Luca Stagnaro, Jean Christophe Salvignol, Jose Lorenzo Alvarez, Gonzalo Saavedra Criado, Luis Gaspar Venancio, Alex Short, Paolo Strada, Tobias Boenke, Cyril Colombo, Adriano Calvi, Elena Maiorano, Osvaldo Piersanti, Sylvain Prezelus, Pierluigi Rosato, Jacques Pinel, Hans Rozemeijer, Valentina Lesna, Paolo Musi, Marco Sias, Alberto Anselmi, Vincent Cazaubiel, Ludovic Vaillon, Yannick Mellier , et al. (17 additional authors not shown)

Abstract: Euclid is a space-based optical/near-infrared survey mission of the European Space Agency (ESA) to investigate the nature of dark energy, dark matter and gravity by observing the geometry of the Universe and on the formation of structures over cosmological timescales. Euclid will use two probes of the signature of dark matter and energy: Weak gravitational Lensing, which requires the measurement o… ▽ More Euclid is a space-based optical/near-infrared survey mission of the European Space Agency (ESA) to investigate the nature of dark energy, dark matter and gravity by observing the geometry of the Universe and on the formation of structures over cosmological timescales. Euclid will use two probes of the signature of dark matter and energy: Weak gravitational Lensing, which requires the measurement of the shape and photometric redshifts of distant galaxies, and Galaxy Clustering, based on the measurement of the 3-dimensional distribution of galaxies through their spectroscopic redshifts. The mission is scheduled for launch in 2020 and is designed for 6 years of nominal survey operations. The Euclid Spacecraft is composed of a Service Module and a Payload Module. The Service Module comprises all the conventional spacecraft subsystems, the instruments warm electronics units, the sun shield and the solar arrays. In particular the Service Module provides the extremely challenging pointing accuracy required by the scientific objectives. The Payload Module consists of a 1.2 m three-mirror Korsch type telescope and of two instruments, the visible imager and the near-infrared spectro-photometer, both covering a large common field-of-view enabling to survey more than 35% of the entire sky. All sensor data are downlinked using K-band transmission and processed by a dedicated ground segment for science data processing. The Euclid data and catalogues will be made available to the public at the ESA Science Data Centre. △ Less

Submitted 18 October, 2016; originally announced October 2016.

Comments: 23 pages, 19 figures, Presented at the SPIE Astronomical Telescopes and Instrumentation conference in Edinburgh, Scotland, United Kingdom, 6 June 1 July 2016

On-orbit performance of the Gaia CCDs at L2

Authors: C. Crowley, R. Kohley, N. C. Hambly, M. Davidson, A. Abreu, F. van Leeuwen, C. Fabricius, G. Seabroke, J. H. J. de Bruijne, A. Short, L. Lindegren, A. G. A. Brown, G. Sarri, P. Gare, T. Prusti, T. Prod'homme, A. Mora, J. Martin-Fleitas, F. Raison, U. Lammers, W. O'Mullane, F. Jansen

Abstract: The European Space Agency's Gaia satellite was launched into orbit around L2 in December 2013 with a payload containing 106 large-format scientific CCDs. The primary goal of the mission is to repeatedly obtain high-precision astrometric and photometric measurements of one thousand million stars over the course of five years. The scientific value of the down-linked data, and the operation of the on… ▽ More The European Space Agency's Gaia satellite was launched into orbit around L2 in December 2013 with a payload containing 106 large-format scientific CCDs. The primary goal of the mission is to repeatedly obtain high-precision astrometric and photometric measurements of one thousand million stars over the course of five years. The scientific value of the down-linked data, and the operation of the onboard autonomous detection chain, relies on the high performance of the detectors. As Gaia slowly rotates and scans the sky, the CCDs are continuously operated in a mode where the line clock rate and the satellite rotation spin-rate are in synchronisation. Nominal mission operations began in July 2014 and the first data release is being prepared for release at the end of Summer 2016. In this paper we present an overview of the focal plane, the detector system, and strategies for on-orbit performance monitoring of the system. This is followed by a presentation of the performance results based on analysis of data acquired during a two-year window beginning at payload switch-on. Results for parameters such as readout noise and electronic offset behaviour are presented and we pay particular attention to the effects of the L2 radiation environment on the devices. The radiation-induced degradation in the charge transfer efficiency (CTE) in the (parallel) scan direction is clearly diagnosed; however, an extrapolation shows that charge transfer inefficiency (CTI) effects at end of mission will be approximately an order of magnitude less than predicted pre-flight. It is shown that the CTI in the serial register (horizontal direction) is still dominated by the traps inherent to the manufacturing process and that the radiation-induced degradation so far is only a few per cent. Finally, we summarise some of the detector effects discovered on-orbit which are still being investigated. △ Less

Submitted 14 September, 2016; originally announced September 2016.

Comments: Published in A&A Gaia special feature

VIS: the visible imager for Euclid

Authors: Mark Cropper, S. Pottinger, S. Niemi, R. Azzollini, J. Denniston, M. Szafraniec, S. Awan, Y. Mellier, M. Berthe, J. Martignac, C. Cara, A. -M. di Giorgio, A. Sciortino, E. Bozzo, L. Genolet, R. Cole, A. Philippon, M. Hailey, T. Hunt, I. Swindells, A. Holland, J. Gow, N. Murray, D. Hall, J. Skottfelt , et al. (11 additional authors not shown)

Abstract: Euclid-VIS is the large format visible imager for the ESA Euclid space mission in their Cosmic Vision program, scheduled for launch in 2020. Together with the near infrared imaging within the NISP instrument, it forms the basis of the weak lensing measurements of Euclid. VIS will image in a single r+i+z band from 550-900 nm over a field of view of ~0.5 deg2. By combining 4 exposures with a total o… ▽ More Euclid-VIS is the large format visible imager for the ESA Euclid space mission in their Cosmic Vision program, scheduled for launch in 2020. Together with the near infrared imaging within the NISP instrument, it forms the basis of the weak lensing measurements of Euclid. VIS will image in a single r+i+z band from 550-900 nm over a field of view of ~0.5 deg2. By combining 4 exposures with a total of 2260 sec, VIS will reach to deeper than mAB=24.5 (10sigma) for sources with extent ~0.3 arcsec. The image sampling is 0.1 arcsec. VIS will provide deep imaging with a tightly controlled and stable point spread function (PSF) over a wide survey area of 15000 deg2 to measure the cosmic shear from nearly 1.5 billion galaxies to high levels of accuracy, from which the cosmological parameters will be measured. In addition, VIS will also provide a legacy dataset with an unprecedented combination of spatial resolution, depth and area covering most of the extra-Galactic sky. Here we will present the results of the study carried out by the Euclid Consortium during the period up to the Critical Design Review. △ Less

Submitted 30 August, 2016; originally announced August 2016.

Comments: 16 pages, 15 figures, 1 table

Journal ref: Proc. SPIE 9904, Space Telescopes and Instrumentation 2016: Optical, Infrared, and Millimeter Wave, 99040Q (July 19, 2016)

How well can Charge Transfer Inefficiency be corrected? A parameter sensitivity study for iterative correction

Authors: Holger Israel, Richard Massey, Thibaut Prod'homme, Mark Cropper, Oliver Cordes, Jason Gow, Ralf Kohley, Ole Marggraf, Sami Niemi, Jason Rhodes, Alex Short, Peter Verhoeve

Abstract: Radiation damage to space-based Charge-Coupled Device (CCD) detectors creates defects which result in an increasing Charge Transfer Inefficiency (CTI) that causes spurious image trailing. Most of the trailing can be corrected during post-processing, by modelling the charge trap** and moving electrons back to where they belong. However, such correction is not perfect -- and damage is continuing t… ▽ More Radiation damage to space-based Charge-Coupled Device (CCD) detectors creates defects which result in an increasing Charge Transfer Inefficiency (CTI) that causes spurious image trailing. Most of the trailing can be corrected during post-processing, by modelling the charge trap** and moving electrons back to where they belong. However, such correction is not perfect -- and damage is continuing to accumulate in orbit. To aid future development, we quantify the limitations of current approaches, and determine where imperfect knowledge of model parameters most degrade measurements of photometry and morphology. As a concrete application, we simulate $1.5\times10^{9}$ "worst case" galaxy and $1.5\times10^{8}$ star images to test the performance of the Euclid visual instrument detectors. There are two separable challenges: If the model used to correct CTI is perfectly the same as that used to add CTI, $99.68$ % of spurious ellipticity is corrected in our setup. This is because readout noise is not subject to CTI, but gets over-corrected during correction. Second, if we assume the first issue to be solved, knowledge of the charge trap density within $Δρ/ρ\!=\!(0.0272\pm0.0005)$ %, and the characteristic release time of the dominant species to be known within $Δτ/τ\!=\!(0.0400\pm0.0004)$ % will be required. This work presents the next level of definition of in-orbit CTI calibration procedures for Euclid. △ Less

Submitted 25 June, 2015; originally announced June 2015.

An Analytical Model of Radiation-Induced Charge Transfer Inefficiency for CCD Detectors

Authors: Alexander Short, Cian Crowley, Jos H. J. de Bruijne, Thibaut Prod'homme

Abstract: The European Space Agency's Gaia mission is scheduled for launch in 2013. It will operate at L2 for 5 years, rotating slowly to scan the sky so that its two optical telescopes will repeatedly observe more than one billion stars. The resulting data set will be iteratively reduced to solve for the position, parallax and proper motion of every observed star. The focal plane contains 106 large area si… ▽ More The European Space Agency's Gaia mission is scheduled for launch in 2013. It will operate at L2 for 5 years, rotating slowly to scan the sky so that its two optical telescopes will repeatedly observe more than one billion stars. The resulting data set will be iteratively reduced to solve for the position, parallax and proper motion of every observed star. The focal plane contains 106 large area silicon CCDs continuously operating in a mode where the line transfer rate and the satellite rotation are in synchronisation. One of the greatest challenges facing the mission is radiation damage to the CCDs which will cause charge deferral and image shape distortion. This is particularly important because of the extreme accuracy requirements of the mission. Despite steps taken at hardware level to minimise the effects of radiation, the residual distortion will need to be calibrated during the pipeline data processing. Due to the volume and inhomogeneity of data involved, this requires a model which describes the effects of the radiation damage which is physically realistic, yet fast enough to implement in the pipeline. The resulting charge distortion model was developed specifically for the Gaia CCD operating mode. However, a generalised version is presented in this paper and this has already been applied in a broader context, for example to investigate the impact of radiation damage on the Euclid dark-energy mission data. △ Less

Submitted 6 February, 2013; originally announced February 2013.

Comments: 8 pages, 5 figures, paper accepted for publication in MNRAS

Electrode level Monte Carlo model of radiation damage effects on astronomical CCDs

Authors: T. Prod'homme, A. G. A. Brown, L. Lindegren, A. D. T. Short, S. W. Brown

Abstract: Current optical space telescopes rely upon silicon Charge Coupled Devices (CCDs) to detect and image the incoming photons. The performance of a CCD detector depends on its ability to transfer electrons through the silicon efficiently, so that the signal from every pixel may be read out through a single amplifier. This process of electron transfer is highly susceptible to the effects of solar proto… ▽ More Current optical space telescopes rely upon silicon Charge Coupled Devices (CCDs) to detect and image the incoming photons. The performance of a CCD detector depends on its ability to transfer electrons through the silicon efficiently, so that the signal from every pixel may be read out through a single amplifier. This process of electron transfer is highly susceptible to the effects of solar proton damage (or non-ionizing radiation damage). This is because charged particles passing through the CCD displace silicon atoms, introducing energy levels into the semi-conductor bandgap which act as localized electron traps. The reduction in Charge Transfer Efficiency (CTE) leads to signal loss and image smearing. The European Space Agency's astrometric Gaia mission will make extensive use of CCDs to create the most complete and accurate stereoscopic map to date of the Milky Way. In the context of the Gaia mission CTE is referred to with the complementary quantity Charge Transfer Inefficiency (CTI = 1-CTE). CTI is an extremely important issue that threatens Gaia's performances. We present here a detailed Monte Carlo model which has been developed to simulate the operation of a damaged CCD at the pixel electrode level. This model implements a new approach to both the charge density distribution within a pixel and the charge capture and release probabilities, which allows the reproduction of CTI effects on a variety of measurements for a large signal level range in particular for signals of the order of a few electrons. A running version of the model as well as a brief documentation and a few examples are readily available at http://www.strw.leidenuniv.nl/~prodhomme/cemga.php as part of the CEMGA java package (CTI Effects Models for Gaia). △ Less

Submitted 18 March, 2011; originally announced March 2011.

Comments: Accepted by MNRAS on 13 February 2011. 15 pages, 7 figures and 5 tables

The Swift X-ray Telescope

Authors: David N. Burrows, J. E. Hill, J. A. Nousek, J. A. Kennea, A. Wells, J. P. Osborne, A. F. Abbey, A. Beardmore, K Mukerjee, A. D. T. Short, G. Chincarini, S. Campana, O. Citterio, A. Moretti, C. Pagani, G. Tagliaferri, P. Giommi, M. Capalbi, F. Tamburelli, L. Angelini, G. Cusumano, H. W. Braeuninger, W. Burkert, G. D. Hartner

Abstract: The Swift Gamma-Ray Explorer is designed to make prompt multiwavelength observations of Gamma-Ray Bursts (GRBs) and GRB afterglows. The X-ray Telescope (XRT) enables Swift to determine GRB positions with a few arcseconds accuracy within 100 seconds of the burst onset. The XRT utilizes a mirror set built for JET-X and an XMM/EPIC MOS CCD detector to provide a sensitive broad-band (0.2-10 keV) X… ▽ More The Swift Gamma-Ray Explorer is designed to make prompt multiwavelength observations of Gamma-Ray Bursts (GRBs) and GRB afterglows. The X-ray Telescope (XRT) enables Swift to determine GRB positions with a few arcseconds accuracy within 100 seconds of the burst onset. The XRT utilizes a mirror set built for JET-X and an XMM/EPIC MOS CCD detector to provide a sensitive broad-band (0.2-10 keV) X-ray imager with effective area of > 120 cm^2 at 1.5 keV, field of view of 23.6 x 23.6 arcminutes, and angular resolution of 18 arcseconds (HPD). The detection sensitivity is 2x10^-14 erg cm^-2 s^-1 in 10^4 seconds. The instrument is designed to provide automated source detection and position reporting within 5 seconds of target acquisition. It can also measure the redshifts of GRBs with Fe line emission or other spectral features. The XRT operates in an auto-exposure mode, adjusting the CCD readout mode automatically to optimize the science return for each frame as the source intensity fades. The XRT will measure spectra and lightcurves of the GRB afterglow beginning about a minute after the burst and will follow each burst for days or weeks. △ Less

Submitted 2 August, 2005; originally announced August 2005.

Comments: 36 pages, 24 figures

Journal ref: SpaceSci.Rev.120:165,2005

The Signature of Supernova Ejecta Measured in the X-ray Afterglow of Gamma-Ray Burst 011211

Authors: J. N. Reeves, D. Watson, J. P. Osborne, K. A. Pounds, P. T. O'Brien, A. D. T. Short, M. J. L. Turner, M. G. Watson, K. O. Mason, M. Ehle, N. Schartel

Abstract: Since their identification with cosmological distances, Gamma-ray bursts (GRBs) have been recognised as the most energetic phenomena in the Universe, with an isotropic burst energy as high as 10^54 ergs. However, the progenitors responsible for the bursts remain elusive, favoured models ranging from a neutron star binary merger, to the collapse of a massive star. Crucial to our understanding of… ▽ More Since their identification with cosmological distances, Gamma-ray bursts (GRBs) have been recognised as the most energetic phenomena in the Universe, with an isotropic burst energy as high as 10^54 ergs. However, the progenitors responsible for the bursts remain elusive, favoured models ranging from a neutron star binary merger, to the collapse of a massive star. Crucial to our understanding of the origins of GRBs is the study of the afterglow emission, where spectroscopy can reveal details of the environment of the burst. Here we report on an XMM-Newton observation of the X-ray afterglow of GRB 011211. The X-ray spectrum reveals evidence for emission lines of Magnesium, Silicon, Sulphur, Argon, Calcium, and possibly Nickel, arising in enriched material with an outflow velocity of order 0.1c. This is the first direct measurement of outflowing matter in a gamma ray burst. The observations strongly favour models where a supernova explosion from a massive stellar progenitor precedes the burst event and is responsible for the outflowing matter. △ Less

Submitted 4 April, 2002; originally announced April 2002.

Comments: 13 pages, including figures. Published in Nature (April 4th issue)

Journal ref: Nature, 416, 512-515 (2002)

The first XMM-Newton spectrum of a high redshift quasar - PKS 0537-286

Authors: J. N. Reeves, M. J. L. Turner, P. J. Bennie, K. A. Pounds, A. Short, P. T. O'Brien, Th. Boller, M. Kuster, A. Tiengo

Abstract: We present XMM-Newton observations of the high redshift z=3.104, radio-loud quasar PKS 0537-286. The EPIC CCD cameras provide the highest signal-to-noise spectrum of a high-z quasar to date. The EPIC observations show that PKS 0537-286 is extremely X-ray luminous (Lx=2x10^47 erg/s), with an unusually hard X-ray spectrum (Gamma=1.27+/-0.02). The flat power-law emission extends over the whole obse… ▽ More We present XMM-Newton observations of the high redshift z=3.104, radio-loud quasar PKS 0537-286. The EPIC CCD cameras provide the highest signal-to-noise spectrum of a high-z quasar to date. The EPIC observations show that PKS 0537-286 is extremely X-ray luminous (Lx=2x10^47 erg/s), with an unusually hard X-ray spectrum (Gamma=1.27+/-0.02). The flat power-law emission extends over the whole observed energy range; there is no evidence of intrinsic absorption, which has been claimed in PKS 0537-286 and other high z quasars. However, there is evidence for weak Compton reflection. A redshifted iron K line, observed at 1.5 keV - corresponding to 6.15 keV in the quasar rest frame - is detected at 95% confidence. If confirmed, this is the most distant iron K line known. The line equivalent width is small (33eV), consistent with the `X-ray Baldwin effect' observed in other luminous quasars. The reflected continuum is also weak (R=0.25). We find the overall spectral energy distribution of PKS 0537-286 is dominated by the X-ray emission, which, together with the flat power-law and weak reflection features, suggests that the X-radiation from PKS 0537-286 is dominated by inverse Compton emission associated with a face-on relativistic jet. △ Less

Submitted 18 October, 2000; originally announced October 2000.

Comments: 6 pages, accepted for publication in Astronomy and Astrophysics Letters