-
Single-mode waveguides for GRAVITY II. Single-mode fibers and Fiber Control Unit
Authors:
G. Perrin,
L. Jocou,
K. Perraut,
J. Ph. Berger,
R. Dembet,
P. Fédou,
S. Lacour,
F. Chapron,
C. Collin,
S. Poulain,
V. Cardin,
F. Joulain,
F. Eisenhauer,
X. Haubois,
S. Gillessen,
M. Haug,
F. Hausmann,
P. Kervella,
P. Léna,
M. Lippa,
O. Pfuh,
S. Rabien,
A. Amorim,
W. Brandner,
C. Straubmeier
Abstract:
The 2nd generation VLTI instrument GRAVITY is a two-field infrared interferometer operating in the K band between 1.97 and 2.43 $μ$m with either the four 8 m or the four 1.8 m telescopes of the Very Large Telescope (VLT). Beams collected by the telescopes are corrected with adaptive optics systems and the fringes are stabilized with a fringe-tracking system. A metrology system allows the measureme…
▽ More
The 2nd generation VLTI instrument GRAVITY is a two-field infrared interferometer operating in the K band between 1.97 and 2.43 $μ$m with either the four 8 m or the four 1.8 m telescopes of the Very Large Telescope (VLT). Beams collected by the telescopes are corrected with adaptive optics systems and the fringes are stabilized with a fringe-tracking system. A metrology system allows the measurement of internal path lengths in order to achieve high-accuracy astrometry. High sensitivity and high interferometric accuracy are achieved thanks to (i) correction of the turbulent phase, (ii) the use of low-noise detectors, and (iii) the optimization of photometric and coherence throughput. Beam combination and most of the beam transport are performed with single-mode waveguides in vacuum and at low temperature. In this paper, we present the functions and performance achieved with weakly birefringent standard single-mode fiber systems in GRAVITY. Fibered differential delay lines (FDDLs) are used to dynamically compensate for up to 6 mm of delay between the science and reference targets. Fibered polarization rotators allow us to align polarizations in the instrument and make the single-mode beam combiner close to polarization neutral. The single-mode fiber system exhibits very low birefringence (less than 23°), very low attenuation (3.6-7 dB/km across the K band), and optimized differential dispersion (less than 2.04 $μ$rad cm2 at zero extension of the FDDLs). As a consequence, the typical fringe contrast losses due to the single-mode fibers are 6% to 10% in the lowest-resolution mode and 5% in the medium- and high-resolution modes of the instrument for a photometric throughput of the fiber chain of the order of 90%. There is no equivalent of this fiber system to route and modally filter beams with delay and polarization control in any other K-band beamcombiner.
△ Less
Submitted 19 January, 2024;
originally announced January 2024.
-
CRIRES$^{+}$ on sky at the ESO Very Large Telescope
Authors:
R. J. Dorn,
P. Bristow,
J. V. Smoker,
F. Rodler,
A. Lavail,
M. Accardo,
M. van den Ancker,
D. Baade,
A. Baruffolo,
B. Courtney-Barrer,
L. Blanco,
A. Brucalassi,
C. Cumani,
R. Follert,
A. Haimerl,
A. Hatzes,
M. Haug,
U. Heiter,
R. Hinterschuster,
N. Hubin,
D. J. Ives,
Y. Jung,
M. Jones,
J-P. Kirchbauer,
B. Klein
, et al. (27 additional authors not shown)
Abstract:
The CRyogenic InfraRed Echelle Spectrograph (CRIRES) Upgrade project CRIRES$^{+}$ extended the capabilities of CRIRES. It transformed this VLT instrument into a cross-dispersed spectrograph to increase the wavelength range that is covered simultaneously by up to a factor of ten. In addition, a new detector focal plane array of three Hawaii 2RG detectors with a 5.3 $μ$m cutoff wavelength replaced t…
▽ More
The CRyogenic InfraRed Echelle Spectrograph (CRIRES) Upgrade project CRIRES$^{+}$ extended the capabilities of CRIRES. It transformed this VLT instrument into a cross-dispersed spectrograph to increase the wavelength range that is covered simultaneously by up to a factor of ten. In addition, a new detector focal plane array of three Hawaii 2RG detectors with a 5.3 $μ$m cutoff wavelength replaced the existing detectors. Amongst many other improvements, a new spectropolarimetric unit was added and the calibration system has been enhanced. The instrument was installed at the VLT on Unit Telescope 3 at the beginning of 2020 and successfully commissioned and verified for science operations during 2021, partly remotely from Europe due to the COVID-19 pandemic. The instrument was subsequently offered to the community from October 2021 onwards. This article describes the performance and capabilities of the upgraded instrument and presents on sky results.
△ Less
Submitted 19 January, 2023;
originally announced January 2023.
-
Measurement of Hadron Production in $π^-$-C Interactions at 158 and 350 GeV/c with NA61/SHINE at the CERN SPS
Authors:
NA61/SHINE Collaboration,
:,
H. Adhikary,
K. K. Allison,
N. Amin,
E. V. Andronov,
T. Antićić,
I. -C. Arsene,
Y. Balkova,
M. Baszczyk,
D. Battaglia,
S. Bhosale,
A. Blondel,
M. Bogomilov,
Y. Bondar,
N. Bostan,
A. Brandin,
A. Bravar,
W. Bryliński,
J. Brzychczyk,
M. Buryakov,
M. Ćirković,
M. Csanad,
J. Cybowska,
T. Czopowicz
, et al. (134 additional authors not shown)
Abstract:
We present a measurement of the momentum spectra of $π^\pm$, K$^\pm$, p$^\pm$, $Λ$, $\barΛ$ and K$^{0}_{S}$ produced in interactions of negatively charged pions with carbon nuclei at beam momenta of 158 and 350 GeV/c. The total production cross sections are measured as well. The data were collected with the large-acceptance spectrometer of the fixed target experiment NA61/SHINE at the CERN SPS. Th…
▽ More
We present a measurement of the momentum spectra of $π^\pm$, K$^\pm$, p$^\pm$, $Λ$, $\barΛ$ and K$^{0}_{S}$ produced in interactions of negatively charged pions with carbon nuclei at beam momenta of 158 and 350 GeV/c. The total production cross sections are measured as well. The data were collected with the large-acceptance spectrometer of the fixed target experiment NA61/SHINE at the CERN SPS. The obtained double-differential $p$-$p_T$ spectra provide a unique reference data set with unprecedented precision and large phase-space coverage to tune models used for the simulation of particle production in extensive air showers in which pions are the most numerous projectiles.
△ Less
Submitted 21 September, 2022;
originally announced September 2022.
-
Detector Systems Engineering for Extremely Large Instruments
Authors:
Elizabeth M. George,
Naidu Bezawada,
Derek Ives,
Leander Mehrgan,
Matteo Accardo,
Domingo Alvarez,
Martin Brinkmann,
Ralf Conzelmann,
Claudio Cumani,
Mark Downing,
Max Engelhardt,
Marcus Haug,
Joshua Hopgood,
Christoph Geimer,
Olaf Iwert,
Barbara Klein,
Christopher Mandla,
Eric Müller,
Suzanne Ramsay,
Javier Reyes,
Mathias Richerzhagen,
Benoît Serra,
Matthias Seidel,
Jörg Stegmeier,
Mirko Todorovic
Abstract:
The scientific detector systems for the ESO ELT first-light instruments, HARMONI, MICADO, and METIS, together will require 27 science detectors: seventeen 2.5 $μ$m cutoff H4RG-15 detectors, four 4K x 4K 231-84 CCDs, five 5.3 $μ$m cutoff H2RG detectors, and one 13.5 $μ$m cutoff GEOSNAP detector. This challenging program of scientific detector system development covers everything from designing and…
▽ More
The scientific detector systems for the ESO ELT first-light instruments, HARMONI, MICADO, and METIS, together will require 27 science detectors: seventeen 2.5 $μ$m cutoff H4RG-15 detectors, four 4K x 4K 231-84 CCDs, five 5.3 $μ$m cutoff H2RG detectors, and one 13.5 $μ$m cutoff GEOSNAP detector. This challenging program of scientific detector system development covers everything from designing and producing state-of-the-art detector control and readout electronics, to develo** new detector characterization techniques in the lab, to performance modeling and final system verification. We report briefly on the current design of these detector systems and developments underway to meet the challenging scientific performance goals of the ELT instruments.
△ Less
Submitted 15 December, 2020;
originally announced December 2020.
-
Multiple Star Systems in the Orion Nebula
Authors:
GRAVITY collaboration,
Martina Karl,
Oliver Pfuhl,
Frank Eisenhauer,
Reinhard Genzel,
Rebekka Grellmann,
Maryam Habibi,
Roberto Abuter,
Matteo Accardo,
António Amorim,
Narsireddy Anugu,
Gerardo Ávila,
Myriam Benisty,
Jean-Philippe Berger,
Nicolas Bland,
Henri Bonnet,
Pierre Bourget,
Wolfgang Brandner,
Roland Brast,
Alexander Buron,
Alessio Caratti o Garatti,
Frédéric Chapron,
Yann Clénet,
Claude Collin,
Vincent Coudé du Foresto
, et al. (111 additional authors not shown)
Abstract:
This work presents an interferometric study of the massive-binary fraction in the Orion Trapezium Cluster with the recently comissioned GRAVITY instrument. We observe a total of 16 stars of mainly OB spectral type. We find three previously unknown companions for $θ^1$ Ori B, $θ^2$ Ori B, and $θ^2$ Ori C. We determine a separation for the previously suspected companion of NU Ori. We confirm four co…
▽ More
This work presents an interferometric study of the massive-binary fraction in the Orion Trapezium Cluster with the recently comissioned GRAVITY instrument. We observe a total of 16 stars of mainly OB spectral type. We find three previously unknown companions for $θ^1$ Ori B, $θ^2$ Ori B, and $θ^2$ Ori C. We determine a separation for the previously suspected companion of NU Ori. We confirm four companions for $θ^1$ Ori A, $θ^1$ Ori C, $θ^1$ Ori D, and $θ^2$ Ori A, all with substantially improved astrometry and photometric mass estimates. We refine the orbit of the eccentric high-mass binary $θ^1$ Ori C and we are able to derive a new orbit for $θ^1$ Ori D. We find a system mass of 21.7 $M_{\odot}$ and a period of $53$ days. Together with other previously detected companions seen in spectroscopy or direct imaging, eleven of the 16 high-mass stars are multiple systems. We obtain a total number of 22 companions with separations up to 600 AU. The companion fraction of the early B and O stars in our sample is about 2, significantly higher than in earlier studies of mostly OB associations. The separation distribution hints towards a bimodality. Such a bimodality has been previously found in A stars, but rarely in OB binaries, which up to this point have been assumed to be mostly compact with a tail of wider companions. We also do not find a substantial population of equal-mass binaries. The observed distribution of mass ratios declines steeply with mass, and like the direct star counts, indicates that our companions follow a standard power law initial mass function. Again, this is in contrast to earlier findings of flat mass ratio distributions in OB associations. We exclude collision as a dominant formation mechanism but find no clear preference for core accretion or competitive accretion.
△ Less
Submitted 27 September, 2018;
originally announced September 2018.
-
GRAVITY chromatic imaging of Eta Car's core
Authors:
GRAVITY Collaboration,
J. Sanchez-Bermudez,
G. Weigelt,
J. M. Bestenlehner,
P. Kervella,
W. Brandner,
Th. Henning,
A. Müller,
G. Perrin,
J. -U. Pott,
M. Schöller,
R. van Boekel,
R. Abuter,
M. Accardo,
A. Amorim,
N. Anugu,
G. Ávila,
M. Benisty,
J. P. Berger,
N. Blind,
H. Bonnet,
P. Bourget,
R. Brast,
A. Buron,
F. Cantalloube
, et al. (110 additional authors not shown)
Abstract:
Eta Car is one of the most intriguing luminous blue variables in the Galaxy. Observations and models at different wavelengths suggest a central binary with a 5.54 yr period residing in its core. 2D and 3D radiative transfer and hydrodynamic simulations predict a primary with a dense and slow stellar wind that interacts with the faster and lower density wind of the secondary. The wind-wind collisio…
▽ More
Eta Car is one of the most intriguing luminous blue variables in the Galaxy. Observations and models at different wavelengths suggest a central binary with a 5.54 yr period residing in its core. 2D and 3D radiative transfer and hydrodynamic simulations predict a primary with a dense and slow stellar wind that interacts with the faster and lower density wind of the secondary. The wind-wind collision scenario suggests that the secondary's wind penetrates the primary's wind creating a low-density cavity in it, with dense walls where the two winds interact. We aim to trace the inner ~5-50 au structure of Eta Car's wind-wind interaction, as seen through BrG and, for the first time, through the He I 2s-2p line. We have used spectro-interferometric observations with GRAVITY at the VLTI. Our modeling of the continuum allows us to estimate its FWHM angular size close to 2 mas and an elongation ratio of 1.06 +/- 0.05 over a PA = 130 +/- 20 deg. Our CMFGEN modeling helped us to confirm that the role of the secondary should be taken into account to properly reproduce the observed BrG and He I lines. Chromatic images across BrG reveal a southeast arc-like feature, possibly associated to the hot post-shocked winds flowing along the cavity wall. The images of He I 2s-2p served to constrain the 20 mas structure of the line-emitting region. The observed morphology of He I suggests that the secondary is responsible for the ionized material that produces the line profile. Both the BrG and the He I 2s-2p maps are consistent with previous hydrodynamical models of the colliding wind scenario. Future dedicated simulations together with an extensive interferometric campaign are necessary to refine our constraints on the wind and stellar parameters of the binary, which finally will help us predict the evolutionary path of Eta Car.
△ Less
Submitted 6 August, 2018;
originally announced August 2018.
-
Detection of the gravitational redshift in the orbit of the star S2 near the Galactic centre massive black hole
Authors:
GRAVITY Collaboration,
R. Abuter,
A. Amorim,
N. Anugu,
M. Bauböck,
M. Benisty,
J. P. Berger,
N. Blind,
H. Bonnet,
W. Brandner,
A. Buron,
C. Collin,
F. Chapron,
Y. Clénet,
V. Coudé du Foresto,
P. T. de Zeeuw,
C. Deen,
F. Delplancke-Ströbele,
R. Dembet,
J. Dexter,
G. Duvert,
A. Eckart,
F. Eisenhauer,
G. Finger,
N. M. Förster Schreiber
, et al. (73 additional authors not shown)
Abstract:
The highly elliptical, 16-year-period orbit of the star S2 around the massive black hole candidate Sgr A* is a sensitive probe of the gravitational field in the Galactic centre. Near pericentre at 120 AU, ~1400 Schwarzschild radii, the star has an orbital speed of ~7650 km/s, such that the first-order effects of Special and General Relativity have now become detectable with current capabilities. O…
▽ More
The highly elliptical, 16-year-period orbit of the star S2 around the massive black hole candidate Sgr A* is a sensitive probe of the gravitational field in the Galactic centre. Near pericentre at 120 AU, ~1400 Schwarzschild radii, the star has an orbital speed of ~7650 km/s, such that the first-order effects of Special and General Relativity have now become detectable with current capabilities. Over the past 26 years, we have monitored the radial velocity and motion on the sky of S2, mainly with the SINFONI and NACO adaptive optics instruments on the ESO Very Large Telescope, and since 2016 and leading up to the pericentre approach in May 2018, with the four-telescope interferometric beam-combiner instrument GRAVITY. From data up to and including pericentre, we robustly detect the combined gravitational redshift and relativistic transverse Doppler effect for S2 of z ~ 200 km/s / c with different statistical analysis methods. When parameterising the post-Newtonian contribution from these effects by a factor f, with f = 0 and f = 1 corresponding to the Newtonian and general relativistic limits, respectively, we find from posterior fitting with different weighting schemes f = 0.90 +/- 0.09 (stat) +\- 0.15 (sys). The S2 data are inconsistent with pure Newtonian dynamics.
△ Less
Submitted 24 July, 2018;
originally announced July 2018.
-
Methods for multiple telescope beam imaging and guiding in the near infrared
Authors:
N. Anugu,
A. Amorim,
P. Gordo,
F. Eisenhauer,
O. Pfuhl,
M. Haug,
E. Wiezorrek,
J. Lima,
G. Perrin,
W. Brandner,
C. Straubmeier,
J. -B. Le Bouquin,
P. J. V Garcia
Abstract:
Atmospheric turbulence and precise measurement of the astrometric baseline vector between any two telescopes are two major challenges in implementing phase referenced interferometric astrometry and imaging. They limit the performance of a fibre-fed interferometer by degrading the instrument sensitivity and astrometric measurements precision and by introducing image reconstruction errors due to ina…
▽ More
Atmospheric turbulence and precise measurement of the astrometric baseline vector between any two telescopes are two major challenges in implementing phase referenced interferometric astrometry and imaging. They limit the performance of a fibre-fed interferometer by degrading the instrument sensitivity and astrometric measurements precision and by introducing image reconstruction errors due to inaccurate phases. A multiple beam acquisition and guiding camera was built to meet these challenges for a recently commissioned four beam combiner instrument, GRAVITY, at the ESO Very Large Telescope Interferometer. For each telescope beam it measures: a) field tip-tilts by imaging stars in the sky; b) telescope pupil shifts by imaging pupil reference laser beacons installed on each telescope using a $2 \times 2$ lenslet; c) higher order aberrations using a $9 \times 9$ Shack-Hartmann. The telescope pupils are imaged for a visual monitoring while observing. These measurements enable active field and pupil guiding by actuating a train of tip-tilt mirrors placed in the pupil and field planes, respectively. The Shack-Hartmann measured quasi-static aberrations are used to focus the Auxiliary Telescopes and allow the possibility of correcting the non-common path errors between the Unit Telescopes adaptive optics systems and GRAVITY. The guiding stabilizes light injection into single-mode fibres, increasing sensitivity and reducing the astrometric and image reconstruction errors. The beam guiding enables to achieve astrometric error less than $50\,μ$as. Here, we report on the data reduction methods and laboratory tests of the multiple beam acquisition and guiding camera and its performance on-sky.
△ Less
Submitted 31 January, 2018;
originally announced January 2018.
-
The wind and the magnetospheric accretion onto the T Tauri star S Coronae Australis at sub-au resolution
Authors:
R. Garcia Lopez,
K. Perraut,
A. Caratti o Garatti,
B. Lazareff,
J. Sanchez-Bermudez,
M. Benisty,
C. Dougados,
L. Labadie,
W. Brandner,
P. J. V. Garcia,
Th. Henning,
T. P. Ray,
R. Abuter,
A. Amorim,
N. Anugu,
J. P. Berger,
H. Bonnet,
A. Buron,
P. Caselli,
Y. Clénet,
V. Coudé du Foresto,
W. de Wit,
C. Deen,
F. Delplancke-Ströbele,
J. Dexter
, et al. (48 additional authors not shown)
Abstract:
To investigate the inner regions of protoplanetary disks, we performed near-infrared interferometric observations of the classical TTauri binary system S CrA. We present the first VLTI-GRAVITY high spectral resolution ($R\sim$4000) observations of a classical TTauri binary, S CrA (composed of S CrA N and S CrA S and separated by $\sim$1.4"), combining the four 8-m telescopes in dual-field mode. Ou…
▽ More
To investigate the inner regions of protoplanetary disks, we performed near-infrared interferometric observations of the classical TTauri binary system S CrA. We present the first VLTI-GRAVITY high spectral resolution ($R\sim$4000) observations of a classical TTauri binary, S CrA (composed of S CrA N and S CrA S and separated by $\sim$1.4"), combining the four 8-m telescopes in dual-field mode. Our observations in the near-infrared K-band continuum reveal a disk around each binary component, with similar half-flux radii of about 0.1 au at d$\sim$130 pc, inclinations ($i=$28$\pm$3$^o$\ and $i=$22$\pm$6$^o$), and position angles (PA=0$^o\pm$6$^o$ and PA=-2$^o\pm$12$^o$), suggesting that they formed from the fragmentation of a common disk. The S CrA N spectrum shows bright HeI and Br$γ$ line emission exhibiting inverse P-Cygni profiles, typically associated with infalling gas. The continuum-compensated Br$γ$ line visibilities of S CrA N show the presence of a compact Br$γ$ emitting region the radius of which is about $\sim$0.06 au, which is twice as big as the truncation radius. This component is mostly tracing a wind. Moreover, a slight radius change between the blue- and red-shifted Br$γ$ line components is marginally detected. The presence of an inverse P-Cygni profile in the HeI and Br$γ$ lines, along with the tentative detection of a slightly larger size of the blue-shifted Br$γ$ line component, hint at the simultaneous presence of a wind and magnetospheric accretion in S CrA N.
△ Less
Submitted 5 September, 2017;
originally announced September 2017.
-
Accretion-ejection morphology of the microquasar SS433 resolved at sub-au scale
Authors:
GRAVITY Collaboration,
P. -O. Petrucci,
I. Waisberg,
J. -B. Le Bouquin,
J. Dexter,
G. Dubus,
K. Perraut,
P. Kervella,
R. Abuter,
A. Amorim,
N. Anugu,
J. P. Berger,
N. Blind,
H. Bonnet,
W. Brandner,
A. Buron,
É. Choquet,
Y. Clénet,
W. de Wit,
C. Deen,
A. Eckart,
F. Eisenhauer,
G. Finger,
P. Garcia,
R. Garcia Lopez
, et al. (45 additional authors not shown)
Abstract:
We present the first optical observation at sub-milliarcsecond (mas) scale of the microquasar SS 433 obtained with the GRAVITY instrument on the VLT interferometer. The 3.5 hour exposure reveals a rich K-band spectrum dominated by hydrogen Br$γ $ and \ion{He}{i} lines, as well as (red-shifted) emission lines coming from the jets. The K-band continuum emitting region is dominated by a marginally re…
▽ More
We present the first optical observation at sub-milliarcsecond (mas) scale of the microquasar SS 433 obtained with the GRAVITY instrument on the VLT interferometer. The 3.5 hour exposure reveals a rich K-band spectrum dominated by hydrogen Br$γ $ and \ion{He}{i} lines, as well as (red-shifted) emission lines coming from the jets. The K-band continuum emitting region is dominated by a marginally resolved point source ($<$ 1 mas) embedded inside a diffuse background accounting for 10\% of the total flux. The jet line positions agree well with the ones expected from the jet kinematic model, an interpretation also supported by the consistent sign (i.e. negative/positive for the receding/approaching jet component) of the phase shifts observed in the lines. The significant visibility drop across the jet lines, together with the small and nearly identical phases for all baselines, point toward a jet that is offset by less than 0.5 mas from the continuum source and resolved in the direction of propagation, with a typical size of 2 mas. The jet position angle of $\sim$80$^{\circ}$ is consistent with the expected one at the observation date. Jet emission so close to the central binary system would suggest that line locking, if relevant to explain the amplitude and stability of the 0.26c jet velocity, operates on elements heavier than hydrogen. The Br$γ $ profile is broad and double peaked. It is better resolved than the continuum and the change of the phase signal sign across the line on all baselines suggests an East-West oriented geometry alike the jet direction and supporting a (polar) disk wind origin.
△ Less
Submitted 5 May, 2017;
originally announced May 2017.
-
Sub-milliarcsecond Optical Interferometry of the HMXB BP Cru with VLTI/GRAVITY
Authors:
GRAVITY Collaboration,
I. Waisberg,
J. Dexter,
O. Pfuhl,
R. Abuter,
A. Amorin,
N. Anugu,
J. P. Berger,
N. Blind,
H. Bonnet,
W. Brandner,
A. Buron,
Y. Clénet,
W. de Wit,
C. Deen,
F. Delplancke-Ströbele,
R. Dembet,
G. Duvert,
A. Eckart,
F. Eisenhauer,
P. Fédou,
G. Finger,
P. Garcia,
R. Garcia Lopez,
E. Gendron
, et al. (46 additional authors not shown)
Abstract:
We observe the HMXB BP Cru using interferometry in the near-infrared K band with VLTI/GRAVITY. Continuum visibilities are at most partially resolved, consistent with the predicted size of the hypergiant. Differential visibility amplitude ($Δ|V| \sim 5\%$) and phase ($Δφ\sim 2 °$) signatures are observed across the HeI $2.059 μ$m and Br$γ$ lines, the latter seen strongly in emission, unusual for th…
▽ More
We observe the HMXB BP Cru using interferometry in the near-infrared K band with VLTI/GRAVITY. Continuum visibilities are at most partially resolved, consistent with the predicted size of the hypergiant. Differential visibility amplitude ($Δ|V| \sim 5\%$) and phase ($Δφ\sim 2 °$) signatures are observed across the HeI $2.059 μ$m and Br$γ$ lines, the latter seen strongly in emission, unusual for the donor star's spectral type. For a baseline $B \sim 100$m, the differential phase RMS $\sim 0.2 °$ corresponds to an astrometric precision of $\sim 2 μ$as. A model-independent analysis in the marginally resolved limit of interferometry reveals asymmetric and extended emission with a strong wavelength dependence. We propose geometric models based on an extended and distorted wind and/or a high density gas stream, which has long been predicted to be present in this system. The observations show that optical interferometry is now able to resolve HMXBs at the spatial scale at which accretion takes place, and therefore probe the effects of the gravitational and radiation fields of the compact object on its environment.
△ Less
Submitted 5 May, 2017;
originally announced May 2017.
-
First Light for GRAVITY: Phase Referencing Optical Interferometry for the Very Large Telescope Interferometer
Authors:
GRAVITY Collaboration,
R. Abuter,
M. Accardo,
A. Amorim,
N. Anugu,
G. Ávila,
N. Azouaoui,
M. Benisty,
J. P. Berger,
N. Blind,
H. Bonnet,
P. Bourget,
W. Brandner,
R. Brast,
A. Buron,
L. Burtscher,
F. Cassaing,
F. Chapron,
É. Choquet,
Y. Clénet,
C. Collin,
V. Coudé du Foresto,
W. de Wit,
P. T. de Zeeuw,
C. Deen
, et al. (108 additional authors not shown)
Abstract:
GRAVITY is a new instrument to coherently combine the light of the European Southern Observatory Very Large Telescope Interferometer to form a telescope with an equivalent 130 m diameter angular resolution and a collecting area of 200 m$^2$. The instrument comprises fiber fed integrated optics beam combination, high resolution spectroscopy, built-in beam analysis and control, near-infrared wavefro…
▽ More
GRAVITY is a new instrument to coherently combine the light of the European Southern Observatory Very Large Telescope Interferometer to form a telescope with an equivalent 130 m diameter angular resolution and a collecting area of 200 m$^2$. The instrument comprises fiber fed integrated optics beam combination, high resolution spectroscopy, built-in beam analysis and control, near-infrared wavefront sensing, phase-tracking, dual beam operation and laser metrology [...]. This article gives an overview of GRAVITY and reports on the performance and the first astronomical observations during commissioning in 2015/16. We demonstrate phase tracking on stars as faint as m$_K$ ~ 10 mag, phase-referenced interferometry of objects fainter than m$_K$ ~ 15 mag with a limiting magnitude of m$_K$ ~ 17 mag, minute long coherent integrations, a visibility accuracy of better than 0.25 %, and spectro-differential phase and closure phase accuracy better than 0.5°, corresponding to a differential astrometric precision of better than 10 microarcseconds (μas). The dual-beam astrometry, measuring the phase difference of two objects with laser metrology, is still under commissioning. First observations show residuals as low as 50 μas when following objects over several months. We illustrate the instrument performance with the observations of archetypical objects for the different instrument modes. Examples include the Galactic Center supermassive black hole and its fast orbiting star S2 for phase referenced dual beam observations and infrared wavefront sensing, the High Mass X-Ray Binary BP Cru and the Active Galactic Nucleus of PDS 456 for few μas spectro-differential astrometry, the T Tauri star S CrA for a spectro-differential visibility analysis, ξ Tel and 24 Cap for high accuracy visibility observations, and η Car for interferometric imaging with GRAVITY.
△ Less
Submitted 5 May, 2017;
originally announced May 2017.
-
The metrology system of the VLTI instrument GRAVITY
Authors:
Magdalena Lippa,
Stefan Gillessen,
Nicolas Blind,
Yipting Kok,
Senol Yazici,
Johannes Weber,
Oliver Pfuhl,
Marcus Haug,
Stefan Kellner,
Ekkehard Wieprecht,
Frank Eisenhauer,
Reinhard Genzel,
Oliver Hans,
Frank Haussmann,
David Huber,
Tobias Kratschmann,
Thomas Ott,
Markus Plattner,
Christian Rau,
Eckhard Sturm,
Idel Waisberg,
Erich Wiezorrek,
Guy Perrin,
Karine Perraut,
Wolfgang Brandner
, et al. (2 additional authors not shown)
Abstract:
The VLTI instrument GRAVITY combines the beams from four telescopes and provides phase-referenced imaging as well as precision-astrometry of order 10 microarcseconds by observing two celestial objects in dual-field mode. Their angular separation can be determined from their differential OPD (dOPD) when the internal dOPDs in the interferometer are known. Here, we present the general overview of the…
▽ More
The VLTI instrument GRAVITY combines the beams from four telescopes and provides phase-referenced imaging as well as precision-astrometry of order 10 microarcseconds by observing two celestial objects in dual-field mode. Their angular separation can be determined from their differential OPD (dOPD) when the internal dOPDs in the interferometer are known. Here, we present the general overview of the novel metrology system which performs these measurements. The metrology consists of a three-beam laser system and a homodyne detection scheme for three-beam interference using phase-shifting interferometry in combination with lock-in amplifiers. Via this approach the metrology system measures dOPDs on a nanometer-level.
△ Less
Submitted 17 August, 2016;
originally announced August 2016.
-
MICADO: first light imager for the E-ELT
Authors:
R. Davies,
J. Schubert,
M. Hartl,
J. Alves,
Y. Clénet,
F. Lang-Bardl,
H. Nicklas,
J. -U. Pott,
R. Ragazzoni,
E. Tolstoy,
T. Agocs,
H. Anwand-Heerwart,
S. Barboza,
P. Baudoz,
R. Bender,
P. Bizenberger,
A. Boccaletti,
W. Boland,
P. Bonifacio,
F. Briegel,
T. Buey,
F. Chapron,
M. Cohen,
O. Czoske,
S. Dreizler
, et al. (59 additional authors not shown)
Abstract:
MICADO will equip the E-ELT with a first light capability for diffraction limited imaging at near-infrared wavelengths. The instrument's observing modes focus on various flavours of imaging, including astrometric, high contrast, and time resolved. There is also a single object spectroscopic mode optimised for wavelength coverage at moderately high resolution. This contribution provides an overview…
▽ More
MICADO will equip the E-ELT with a first light capability for diffraction limited imaging at near-infrared wavelengths. The instrument's observing modes focus on various flavours of imaging, including astrometric, high contrast, and time resolved. There is also a single object spectroscopic mode optimised for wavelength coverage at moderately high resolution. This contribution provides an overview of the key functionality of the instrument, outlining the scientific rationale for its observing modes. The interface between MICADO and the adaptive optics system MAORY that feeds it is summarised. The design of the instrument is discussed, focussing on the optics and mechanisms inside the cryostat, together with a brief overview of the other key sub-systems.
△ Less
Submitted 7 July, 2016;
originally announced July 2016.
-
GRAVITY: the VLTI 4-beam combiner for narrow-angle astrometry and interferometric imaging
Authors:
N. Blind,
F. Eisenhauer,
S. Gillessen,
Y. Kok,
M. Lippa,
G. Perrin,
R. Dembet,
P. Fedou,
S. Lacour,
K. Perraut,
L. Jocou,
L. Burtscher,
O. Hans,
M. Haug,
F. Haussmann,
S. Huber,
A. Janssen,
S. Kellner,
T. Ott,
O. Pfuhl,
E. Sturm,
J. Weber,
E. Wieprecht,
A. Amorim,
W. Brandner
, et al. (1 additional authors not shown)
Abstract:
GRAVITY is the second generation Very Large Telescope Interferometer instrument for precision narrow-angle astrometry and interferometric imaging in the Near Infra-Red (NIR). It shall provide precision astrometry of order 10 microarcseconds, and imaging capability at a few milliarcsecond resolution, and hence will revolutionise dynamical measurements of celestial objects. GRAVITY is currently in t…
▽ More
GRAVITY is the second generation Very Large Telescope Interferometer instrument for precision narrow-angle astrometry and interferometric imaging in the Near Infra-Red (NIR). It shall provide precision astrometry of order 10 microarcseconds, and imaging capability at a few milliarcsecond resolution, and hence will revolutionise dynamical measurements of celestial objects. GRAVITY is currently in the last stages of its integration and tests in Garching at MPE, and will be delivered to the VLT Interferometer (VLTI) in 2015. We present here the instrument, with a particular focus on the components making use of fibres: integrated optics beam combiners, polarisation rotators, fibre differential delay lines, and the metrology.
△ Less
Submitted 25 March, 2015;
originally announced March 2015.
-
The GRAVITY instrument software / High-level software
Authors:
Leonard Burtscher,
Ekkehard Wieprecht,
Thomas Ott,
Yit** Kok,
Senol Yazici,
Narsireddy Anugu,
Roderick Dembet,
Pierre Fedou,
Sylvestre Lacour,
Juergen Ott,
Thibaut Paumard,
Vincent Lapeyrere,
Pierre Kervella,
Roberto Abuter,
Eszter Pozna,
Frank Eisenhauer,
Nicolas Blind,
Reinhard Genzel,
Stefan Gillessen,
Oliver Hans,
Marcus Haug,
Frank Haussmann,
Stefan Kellner,
Magdalena Lippa,
Oliver Pfuhl
, et al. (8 additional authors not shown)
Abstract:
GRAVITY is the four-beam, near- infrared, AO-assisted, fringe tracking, astrometric and imaging instrument for the Very Large Telescope Interferometer (VLTI). It is requiring the development of one of the most complex instrument software systems ever built for an ESO instrument. Apart from its many interfaces and interdependencies, one of the most challenging aspects is the overall performance and…
▽ More
GRAVITY is the four-beam, near- infrared, AO-assisted, fringe tracking, astrometric and imaging instrument for the Very Large Telescope Interferometer (VLTI). It is requiring the development of one of the most complex instrument software systems ever built for an ESO instrument. Apart from its many interfaces and interdependencies, one of the most challenging aspects is the overall performance and stability of this complex system. The three infrared detectors and the fast reflective memory network (RMN) recorder contribute a total data rate of up to 20 MiB/s accumulating to a maximum of 250 GiB of data per night. The detectors, the two instrument Local Control Units (LCUs) as well as the five LCUs running applications under TAC (Tools for Advanced Control) architecture, are interconnected with fast Ethernet, RMN fibers and dedicated fiber connections as well as signals for the time synchronization. Here we give a simplified overview of all subsystems of GRAVITY and their interfaces and discuss two examples of high-level applications during observations: the acquisition procedure and the gathering and merging of data to the final FITS file.
△ Less
Submitted 23 January, 2015;
originally announced January 2015.
-
The GRAVITY metrology system: narrow-angle astrometry via phase-shifting interferometry
Authors:
M. Lippa,
N. Blind,
S. Gillessen,
Y. Kok,
J. Weber,
F. Eisenhauer,
O. Pfuhl,
A. Janssen,
M. Haug,
F. Haußmann,
S. Kellner,
O. Hans,
E. Wieprecht,
T. Ott,
L. Burtscher,
R. Genzel,
E. Sturm,
R. Hofmann,
S. Huber,
D. Huber,
S. Senftleben,
A. Pflüger,
R. Greßmann,
G. Perrin,
K. Perraut
, et al. (4 additional authors not shown)
Abstract:
The VLTI instrument GRAVITY will provide very powerful astrometry by combining the light from four telescopes for two objects simultaneously. It will measure the angular separation between the two astronomical objects to a precision of 10 microarcseconds. This corresponds to a differential optical path difference (dOPD) between the targets of few nanometers and the paths within the interferometer…
▽ More
The VLTI instrument GRAVITY will provide very powerful astrometry by combining the light from four telescopes for two objects simultaneously. It will measure the angular separation between the two astronomical objects to a precision of 10 microarcseconds. This corresponds to a differential optical path difference (dOPD) between the targets of few nanometers and the paths within the interferometer have to be maintained stable to that level. For this purpose, the novel metrology system of GRAVITY will monitor the internal dOPDs by means of phase-shifting interferometry. We present the four-step phase-shifting concept of the metrology with emphasis on the method used for calibrating the phase shifts. The latter is based on a phase-step insensitive algorithm which unambiguously extracts phases in contrast to other methods that are strongly limited by non-linearities of the phase-shifting device. The main constraint of this algorithm is to introduce a robust ellipse fitting routine. Via this approach we are able to measure phase shifts in the laboratory with a typical accuracy of lambda/2000 or 1 nanometer of the metrology wavelength.
△ Less
Submitted 20 January, 2015;
originally announced January 2015.
-
The fiber coupler and beam stabilization system of the GRAVITY interferometer
Authors:
O. Pfuhl,
M. Haug,
F. Eisenhauer,
S. Kellner,
F. Haussmann,
G. Perrin,
S. Gillessen,
C. Straubmeier,
T. Ott,
K. Rousselet-Perraut,
A. Amorim,
M. Lippa,
A. Janssen,
W. Brandner,
Y. Kok,
N. Blind,
L. Burtscher,
E. Sturm,
E. Wieprecht,
M. Schoeller,
J. Weber,
O. Hans,
S. Huber
Abstract:
We present the installed and fully operational beam stabilization and fiber injection subsystem feeding the 2nd generation VLTI instrument GRAVITY. The interferometer GRAVITY requires an unprecedented stability of the VLTI optical train to achieve micro-arcsecond astrometry. For this purpose, GRAVITY contains four fiber coupler units, one per telescope. Each unit is equipped with actuators to stab…
▽ More
We present the installed and fully operational beam stabilization and fiber injection subsystem feeding the 2nd generation VLTI instrument GRAVITY. The interferometer GRAVITY requires an unprecedented stability of the VLTI optical train to achieve micro-arcsecond astrometry. For this purpose, GRAVITY contains four fiber coupler units, one per telescope. Each unit is equipped with actuators to stabilize the telescope beam in terms of tilt and lateral pupil displacement, to rotate the field, to adjust the polarization and to compensate atmospheric piston. A special roof-prism offers the possibility of on-axis as well as off-axis fringe tracking without changing the optical train. We describe the assembly, integration and alignment and the resulting optical quality and performance of the individual units. Finally, we present the closed-loop performance of the tip-tilt and pupil tracking achieved with the final systems in the lab.
△ Less
Submitted 4 December, 2014;
originally announced December 2014.
-
The GRAVITY metrology system: modeling a metrology in optical fibers
Authors:
N. Blind,
H. Huber,
F. Eisenhauer,
J. Weber,
S. Gillessen,
M. Lippa,
L. Burtscher,
O. Hans,
M. Haug,
F. Haussmann,
S. Huber,
A. Janssen,
S. Kellner,
Y. Kok,
T. Ott,
O. Pfuhl,
E. Sturm,
E. Wieprecht,
A. Amorim,
W. Brandner,
G. Perrin,
K. Perraut,
C. Straubmeier
Abstract:
GRAVITY is the second generation VLT Interferometer (VLTI) instrument for high-precision narrow-angle astrometry and phase-referenced interferometric imaging. The laser metrology system of GRAVITY is at the heart of its astrometric mode, which must measure the distance of 2 stars with a precision of 10 micro-arcseconds. This means the metrology has to measure the optical path difference between th…
▽ More
GRAVITY is the second generation VLT Interferometer (VLTI) instrument for high-precision narrow-angle astrometry and phase-referenced interferometric imaging. The laser metrology system of GRAVITY is at the heart of its astrometric mode, which must measure the distance of 2 stars with a precision of 10 micro-arcseconds. This means the metrology has to measure the optical path difference between the two beam combiners of GRAVITY to a level of 5 nm. The metrology design presents some non-common paths that have consequently to be stable at a level of 1 nm. Otherwise they would impact the performance of GRAVITY. The various tests we made in the past on the prototype give us hints on the components responsible for this error, and on their respective contribution to the total error. It is however difficult to assess their exact origin from only OPD measurements, and therefore, to propose a solution to this problem. In this paper, we present the results of a semi-empirical modeling of the fibered metrology system, relying on theoretical basis, as well as on characterisations of key components. The modeling of the metrology system regarding various effects, e.g., temperature, waveguide heating or mechanical stress, will help us to understand how the metrology behave. The goals of this modeling are to 1) model the test set-ups and reproduce the measurements (as a validation of the modeling), 2) determine the origin of the non-common path errors, and 3) propose modifications to the current metrology design to reach the required 1nm stability.
△ Less
Submitted 24 July, 2014;
originally announced July 2014.
-
GRAVITY: the Calibration Unit
Authors:
N. Blind,
F. Eisenhauer,
M. Haug,
S. Gillessen,
M. Lippa,
L. Burtscher,
O. Hans,
F. Haussmann,
S. Huber,
A. Janssen,
S. Kellner,
Y. Kok,
T. Ott,
O. Pfuhl,
E. Sturm,
J. Weber,
E. Wieprecht,
A. Amorim,
W. Brandner,
G. Perrin,
K. Perraut,
C. Straubmeier
Abstract:
We present in this paper the design and characterisation of a new sub-system of the VLTI 2nd generation instrument GRAVITY: the Calibration Unit. The Calibration Unit provides all functions to test and calibrate the beam combiner instrument: it creates two artificial stars on four beams, and dispose of four delay lines with an internal metrology. It also includes artificial stars for the tip-tilt…
▽ More
We present in this paper the design and characterisation of a new sub-system of the VLTI 2nd generation instrument GRAVITY: the Calibration Unit. The Calibration Unit provides all functions to test and calibrate the beam combiner instrument: it creates two artificial stars on four beams, and dispose of four delay lines with an internal metrology. It also includes artificial stars for the tip-tilt and pupil guiding systems, as well as four metrology pick-up diodes, for tests and calibration of the corresponding sub-systems. The calibration unit also hosts the reference targets to align GRAVITY to the VLTI, and the safety shutters to avoid the metrology light to propagate in the VLTI-lab. We present the results of the characterisation and validtion of these differrent sub-units.
△ Less
Submitted 24 July, 2014;
originally announced July 2014.
-
GRAVITY: beam stabilization and light injection subsystems
Authors:
O. Pfuhl,
M. Haug,
F. Eisenhauer,
D. Penka,
A. Amorim,
S. Kellner,
S. Gillessen,
T. Ott,
E. Wieprecht,
E. Sturm,
F. Haussmann,
M. Lippa
Abstract:
We present design results of the 2nd generation VLTI instrument GRAVITY beam stabilization and light injection subsystems. Designed to deliver micro-arcsecond astrometry, GRAVITY requires an unprecedented stability of the VLTI optical train. To meet the astrometric requirements, we have developed a dedicated 'laser guiding system', correcting the longitudinal and lateral pupil position as well as…
▽ More
We present design results of the 2nd generation VLTI instrument GRAVITY beam stabilization and light injection subsystems. Designed to deliver micro-arcsecond astrometry, GRAVITY requires an unprecedented stability of the VLTI optical train. To meet the astrometric requirements, we have developed a dedicated 'laser guiding system', correcting the longitudinal and lateral pupil position as well as the image jitter. The actuators for the correction are provided by four 'fiber coupler' units located in the GRAVITY cryostat. Each fiber coupler picks the light of one telescope and stabilizes the beam. Furthermore each unit provides field de-rotation, polarization analysis as well as atmospheric piston correction. Using a novel roof prism design offers the possibility of on-axis as well as off-axis fringe tracking without changing the optical path. Finally the stabilized beam is injected with minimized losses into single-mode fibers via parabolic mirrors. We present lab results of the first guiding- as well as the first fiber coupler prototype regarding the closed loop performance and the optical quality. Based on the lab results we discuss the on-sky performance of the system and the implications concerning the sensitivity of GRAVITY.
△ Less
Submitted 20 December, 2012;
originally announced December 2012.
-
GRAVITY: metrology
Authors:
S. Gillessen,
M. Lippa,
F. Eisenhauer,
O. Pfuhl,
M. Haug,
S. Kellner,
T. Ott,
E. Wieprecht,
E. Sturm,
F. Haussmann,
C. F. Kister,
D. Moch,
M. Thiel
Abstract:
GRAVITY is a second generation VLTI instrument, combining the light of four telescopes and two objects simultaneously. The main goal is to obtain astrometrically accurate information. Besides correctly measured stellar phases this requires the knowledge of the instrumental differential phase, which has to be measured optically during the astronomical observations. This is the purpose of a dedicate…
▽ More
GRAVITY is a second generation VLTI instrument, combining the light of four telescopes and two objects simultaneously. The main goal is to obtain astrometrically accurate information. Besides correctly measured stellar phases this requires the knowledge of the instrumental differential phase, which has to be measured optically during the astronomical observations. This is the purpose of a dedicated metrology system. The GRAVITY metrology covers the full optical path, from the beam combiners up to the reference points in the beam of the primary telescope mirror, minimizing the systematic uncertainties and providing a proper baseline in astrometric terms. Two laser beams with a fixed phase relation travel backward the whole optical chain, creating a fringe pattern in any plane close to a pupil. By temporal encoding the phase information can be extracted at any point by means of flux measurements with photo diodes. The reference points chosen sample the pupil at typical radii, eliminating potential systematics due differential focus. We present the final design and the performance estimate, which is in accordance with the overall requirements for GRAVITY.
△ Less
Submitted 12 September, 2012;
originally announced September 2012.
-
The Fringe Detection Laser Metrology for the GRAVITY Interferometer at the VLTI
Authors:
H. Bartko,
S. Gillessen,
S. Rabien,
M. Thiel,
A. Gräter,
M. Haug,
S. Kellner,
F. Eisenhauer,
S. Lacour,
C. Straubmeier,
J. -P. Berger,
L. Jocou,
W. Chibani,
S. Lüst,
D. Moch,
O. Pfuhl,
W. Fabian,
C. Araujo-Hauck,
K. Perraut,
W. Brandner,
G. Perrin,
A. Amorim
Abstract:
Interferometric measurements of optical path length differences of stars over large baselines can deliver extremely accurate astrometric data. The interferometer GRAVITY will simultaneously measure two objects in the field of view of the Very Large Telescope Interferometer (VLTI) of the European Southern Observatory (ESO) and determine their angular separation to a precision of 10 micro arcseconds…
▽ More
Interferometric measurements of optical path length differences of stars over large baselines can deliver extremely accurate astrometric data. The interferometer GRAVITY will simultaneously measure two objects in the field of view of the Very Large Telescope Interferometer (VLTI) of the European Southern Observatory (ESO) and determine their angular separation to a precision of 10 micro arcseconds in only 5 minutes. To perform the astrometric measurement with such a high accuracy, the differential path length through the VLTI and the instrument has to be measured (and tracked since Earth's rotation will permanently change it) by a laser metrology to an even higher level of accuracy (corresponding to 1 nm in 3 minutes). Usually, heterodyne differential path techniques are used for nanometer precision measurements, but with these methods it is difficult to track the full beam size and to follow the light path up to the primary mirror of the telescope. Here, we present the preliminary design of a differential path metrology system, developed within the GRAVITY project. It measures the instrumental differential path over the full pupil size and up to the entrance pupil location. The differential phase is measured by detecting the laser fringe pattern both on the telescopes' secondary mirrors as well as after reflection at the primary mirror. Based on our proposed design we evaluate the phase measurement accuracy based on a full budget of possible statistical and systematic errors. We show that this metrology design fulfills the high precision requirement of GRAVITY.
△ Less
Submitted 11 July, 2010;
originally announced July 2010.
-
GRAVITY: a four-telescope beam combiner instrument for the VLTI
Authors:
S. Gillessen,
F. Eisenhauer,
G. Perrin,
W. Brandner,
C. Straubmeier,
K. Perraut,
A. Amorim,
M. Schöller,
C. Araujo-Hauck,
H. Bartko,
H. Baumeister,
J. -P. Berger,
P. Carvas,
F. Cassaing,
F. Chapron,
E. Choquet,
Y. Clenet,
C. Collin,
A. Eckart,
P. Fedou,
S. Fischer,
E. Gendron,
R. Genzel,
P. Gitton,
F. Gonte
, et al. (38 additional authors not shown)
Abstract:
GRAVITY is an adaptive optics assisted Beam Combiner for the second generation VLTI instrumentation. The instrument will provide high-precision narrow-angle astrometry and phase-referenced interferometric imaging in the astronomical K-band for faint objects. We describe the wide range of science that will be tackled with this instrument, highlighting the unique capabilities of the VLTI in combinat…
▽ More
GRAVITY is an adaptive optics assisted Beam Combiner for the second generation VLTI instrumentation. The instrument will provide high-precision narrow-angle astrometry and phase-referenced interferometric imaging in the astronomical K-band for faint objects. We describe the wide range of science that will be tackled with this instrument, highlighting the unique capabilities of the VLTI in combination with GRAVITY. The most prominent goal is to observe highly relativistic motions of matter close to the event horizon of Sgr A*, the massive black hole at center of the Milky Way. We present the preliminary design that fulfils the requirements that follow from the key science drivers: It includes an integrated optics, 4-telescope, dual feed beam combiner operated in a cryogenic vessel; near-infrared wavefrontsensing adaptive optics; fringe-tracking on secondary sources within the field of view of the VLTI and a novel metrology concept. Simulations show that 10 μas astrometry within few minutes is feasible for a source with a magnitude of mK = 15 like Sgr A*, given the availability of suitable phase reference sources (mK = 10). Using the same setup, imaging of mK = 18 stellar sources in the interferometric field of view is possible, assuming a full night of observations and the corresponding UV coverage of the VLTI.
△ Less
Submitted 9 July, 2010;
originally announced July 2010.
-
LIINUS/SERPIL: a design study for interferometric imaging spectroscopy at the LBT
Authors:
F. Mueller Sanchez,
C. Gal,
F. Eisenhauer,
A. Krabbe,
M. Haug,
C. Iserlohe,
T. M. Herbst
Abstract:
We present two design concepts and the science drivers of a proposed near-infrared interferometric integral field spectrograph for the LBT. This instrument will expand the capabilities of the currently-under-construction interferometric camera LINC-NIRVANA with spectroscopy by means of an integral field unit (IFU) located inside the LINC cryostat. Two instrument concepts have been studied in det…
▽ More
We present two design concepts and the science drivers of a proposed near-infrared interferometric integral field spectrograph for the LBT. This instrument will expand the capabilities of the currently-under-construction interferometric camera LINC-NIRVANA with spectroscopy by means of an integral field unit (IFU) located inside the LINC cryostat. Two instrument concepts have been studied in detail: a microlens array IFU with a spectrograph built entirely inside LINC (the LIINUS approach), and a lenslet+fibers IFU feeding an external spectrograph (the SERPIL approach). In both cases, the instrument incorporates imaging interferometry with integral field spectroscopy, an ideal combination for detailed studies of astronomical objects down to below 10mas angular resolution in the near-infrared. The scientific applications range from solar system studies and spectroscopy of exoplanets to the dynamics of stars and gas in the central regions of the Milky Way and other nearby galaxies.
△ Less
Submitted 29 September, 2008;
originally announced September 2008.
-
GRAVITY: getting to the event horizon of Sgr A*
Authors:
F. Eisenhauer,
G. Perrin,
W. Brandner,
C. Straubmeier,
A. Richichi,
S. Gillessen,
J. P. Berger,
S. Hippler,
A. Eckart,
M. Schoeller,
S. Rabien,
F. Cassaing,
R. Lenzen,
M. Thiel,
Y. Clenet,
J. R. Ramos,
S. Kellner,
P. Fedou,
H. Baumeister,
R. Hofmann,
E. Gendron,
A. Boehm,
H. Bartko,
X. Haubois,
R. Klein
, et al. (23 additional authors not shown)
Abstract:
We present the second-generation VLTI instrument GRAVITY, which currently is in the preliminary design phase. GRAVITY is specifically designed to observe highly relativistic motions of matter close to the event horizon of Sgr A*, the massive black hole at center of the Milky Way. We have identified the key design features needed to achieve this goal and present the resulting instrument concept.…
▽ More
We present the second-generation VLTI instrument GRAVITY, which currently is in the preliminary design phase. GRAVITY is specifically designed to observe highly relativistic motions of matter close to the event horizon of Sgr A*, the massive black hole at center of the Milky Way. We have identified the key design features needed to achieve this goal and present the resulting instrument concept. It includes an integrated optics, 4-telescope, dual feed beam combiner operated in a cryogenic vessel; near infrared wavefront sensing adaptive optics; fringe tracking on secondary sources within the field of view of the VLTI and a novel metrology concept. Simulations show that the planned design matches the scientific needs; in particular that 10 microarcsecond astrometry is feasible for a source with a magnitude of K=15 like Sgr A*, given the availability of suitable phase reference sources.
△ Less
Submitted 1 August, 2008;
originally announced August 2008.
