-
The Power Board of the KM3NeT Digital Optical Module: design, upgrade, and production
Authors:
S. Aiello,
A. Albert,
S. Alves Garre,
Z. Aly,
A. Ambrosone,
F. Ameli,
M. Andre,
E. Androutsou,
M. Anguita,
L. Aphecetche,
M. Ardid,
S. Ardid,
H. Atmani,
J. Aublin,
F. Badaracco,
L. Bailly-Salins,
Z. Bardacova,
B. Baret,
A. Bariego Quintana,
S. Basegmez du Pree,
Y. Becherini,
M. Bendahman,
F. Benfenati,
M. Benhassi,
D. M. Benoit
, et al. (259 additional authors not shown)
Abstract:
The KM3NeT Collaboration is building an underwater neutrino observatory at the bottom of the Mediterranean Sea consisting of two neutrino telescopes, both composed of a three-dimensional array of light detectors, known as digital optical modules. Each digital optical module contains a set of 31 three inch photomultiplier tubes distributed over the surface of a 0.44 m diameter pressure-resistant gl…
▽ More
The KM3NeT Collaboration is building an underwater neutrino observatory at the bottom of the Mediterranean Sea consisting of two neutrino telescopes, both composed of a three-dimensional array of light detectors, known as digital optical modules. Each digital optical module contains a set of 31 three inch photomultiplier tubes distributed over the surface of a 0.44 m diameter pressure-resistant glass sphere. The module includes also calibration instruments and electronics for power, readout and data acquisition. The power board was developed to supply power to all the elements of the digital optical module. The design of the power board began in 2013, and several prototypes were produced and tested. After an exhaustive validation process in various laboratories within the KM3NeT Collaboration, a mass production batch began, resulting in the construction of over 1200 power boards so far. These boards were integrated in the digital optical modules that have already been produced and deployed, 828 until October 2023. In 2017, an upgrade of the power board, to increase reliability and efficiency, was initiated. After the validation of a pre-production series, a production batch of 800 upgraded boards is currently underway. This paper describes the design, architecture, upgrade, validation, and production of the power board, including the reliability studies and tests conducted to ensure the safe operation at the bottom of the Mediterranean Sea throughout the observatory's lifespan
△ Less
Submitted 24 November, 2023;
originally announced November 2023.
-
Timing performances of NectarCAM, a Medium Sized Telescope Camera for the Cherenkov Telescope Array
Authors:
H. Rueda,
F. Bradascio,
J. A. Barrio,
J. Biteau,
F. Brun,
C. Champion,
J-F. Glicenstein,
D. Hoffmann,
P. Jean,
J. P. Lenain,
F. Louis,
A. Pérez,
M. Punch,
P. Sizun,
K-H. Sulanke,
L. A. Tejedor,
B. Vallage
Abstract:
NectarCAM is a Cherenkov camera that will be installed on Medium-Sized Telescopes of the northern array of the Cherenkov Telescope Array Observatory (CTAO). It is composed of 265 modules, each of which includes 7 photo-multiplier tubes, a Front-End Board and a camera trigger system for data collection. The first NectarCAM unit is currently being integrated at CEA Paris-Saclay in France. Once insta…
▽ More
NectarCAM is a Cherenkov camera that will be installed on Medium-Sized Telescopes of the northern array of the Cherenkov Telescope Array Observatory (CTAO). It is composed of 265 modules, each of which includes 7 photo-multiplier tubes, a Front-End Board and a camera trigger system for data collection. The first NectarCAM unit is currently being integrated at CEA Paris-Saclay in France. Once installed at the CTAO's northern site, the NectarCAM's timing abilities will be crucial for reducing noise in images, improving image cleaning, and distinguishing between gamma-ray photons and cosmic-ray background. Additionally, it will enable coincidence identification with neighboring telescopes for stereoscopic observations. The timing system of NectarCAM has been tested in a dark room with various light sources. The results of the tests, including timing precision and accuracy of the trigger arrival relative to a laser source, and the timing of individual and multiple pixel signals, will be presented.
△ Less
Submitted 10 October, 2023;
originally announced October 2023.
-
The NectarCAM Timing System
Authors:
F. Bradascio,
H. Rueda,
J. A. Barrio,
J. Biteau,
F. Brun,
C. Champion,
J-F. Glicenstein,
D. Hoffmann,
P. Jean,
J. P. Lenain,
F. Louis,
A. Pérez,
M. Punch,
P. Sizun,
K. -H. Sulanke,
L. A. Tejedor,
B. Vallage
Abstract:
NectarCAM is a Cherenkov camera which is going to equip the Medium-Sized Telescopes (MST) of the northern site of the Cherenkov Telescope Array Observatory (CTAO). NectarCAM is equipped with 265 modules, each consisting of 7 photo-multiplier tubes (PMTs), a Front-End Board and a local camera trigger system used for data acquisition. This paper addresses the timing performance of NectarCAM which ar…
▽ More
NectarCAM is a Cherenkov camera which is going to equip the Medium-Sized Telescopes (MST) of the northern site of the Cherenkov Telescope Array Observatory (CTAO). NectarCAM is equipped with 265 modules, each consisting of 7 photo-multiplier tubes (PMTs), a Front-End Board and a local camera trigger system used for data acquisition. This paper addresses the timing performance of NectarCAM which are crucial to reduce the noise in shower images and improve image cleaning as well as to discriminate between gamma-ray photons and cosmic-ray background and finally to allow coincidence identification with neighbouring telescopes for stereoscopic operations. Verification tests of the system have been performed in a dark room using various light sources to illuminate the first NectarCAM unit. The resulting timing precision and accuracy of the trigger arrival relative to a laser source, of individual and multiple pixel signals have been studied and are shown to comply to CTAO requirements.
△ Less
Submitted 28 June, 2023; v1 submitted 31 January, 2023;
originally announced January 2023.
-
TiCkS: A Flexible White-Rabbit Based Time-Stam** Board
Authors:
C. Champion,
M. Punch,
R. Oger,
S. Colonges,
Y. Moudden
Abstract:
We have developed the TiCkS board (Time and Clock Stam**) based on the White Rabbit (WR) SPEC node (Simple PCIe FMC carrier), to provide ns-precision time-stamps (TSs) of input signals (e.g., triggers from a connected device) and transmission of these TSs to a central collection point. TiCkS was developed within the specifications of the Cherenkov Telescope Array (CTA) as one of the candidate TS…
▽ More
We have developed the TiCkS board (Time and Clock Stam**) based on the White Rabbit (WR) SPEC node (Simple PCIe FMC carrier), to provide ns-precision time-stamps (TSs) of input signals (e.g., triggers from a connected device) and transmission of these TSs to a central collection point. TiCkS was developed within the specifications of the Cherenkov Telescope Array (CTA) as one of the candidate TS nodes, with a small form-factor allowing its use in any CTA camera. The essence of this development concerns the firmware in its Spartan-6 FPGA (Field-Programmable Gate Array), with the addition of: 1) a ns-precision TDC (Time-to-Digital Convertor) for the TSs; and 2) a UDP stack (User Datagram Protocol) to send TSs and auxiliary information over the WR fibre, and to receive configuration & slow control commands over the same fibre. It also provides a PPS (Pulse Per Second) and other clock signals to the connected device, from which it can receive auxiliary event-type information over an SPI link (Serial Peripheral Interface). A version of TiCkS with an FMC connector (FPGA Mezzanine Card) will be made available in the WR OpenHardware repository, so allowing the use of a mezzanine card with varied formats of input/output connectors, providing a cheap, flexible, and reliable solution for ns-precision time-stam** of trigger signals up to 400 kHz, for use in other experiments.
△ Less
Submitted 19 October, 2017;
originally announced October 2017.
-
Cherenkov Telescope Array Contributions to the 35th International Cosmic Ray Conference (ICRC2017)
Authors:
F. Acero,
B. S. Acharya,
V. Acín Portella,
C. Adams,
I. Agudo,
F. Aharonian,
I. Al Samarai,
A. Alberdi,
M. Alcubierre,
R. Alfaro,
J. Alfaro,
C. Alispach,
R. Aloisio,
R. Alves Batista,
J. -P. Amans,
E. Amato,
L. Ambrogi,
G. Ambrosi,
M. Ambrosio,
J. Anderson,
M. Anduze,
E. O. Angüner,
E. Antolini,
L. A. Antonelli,
V. Antonuccio
, et al. (1117 additional authors not shown)
Abstract:
List of contributions from the Cherenkov Telescope Array Consortium presented at the 35th International Cosmic Ray Conference, July 12-20 2017, Busan, Korea.
List of contributions from the Cherenkov Telescope Array Consortium presented at the 35th International Cosmic Ray Conference, July 12-20 2017, Busan, Korea.
△ Less
Submitted 24 October, 2017; v1 submitted 11 September, 2017;
originally announced September 2017.
-
Contributions of the Cherenkov Telescope Array (CTA) to the 6th International Symposium on High-Energy Gamma-Ray Astronomy (Gamma 2016)
Authors:
The CTA Consortium,
:,
A. Abchiche,
U. Abeysekara,
Ó. Abril,
F. Acero,
B. S. Acharya,
C. Adams,
G. Agnetta,
F. Aharonian,
A. Akhperjanian,
A. Albert,
M. Alcubierre,
J. Alfaro,
R. Alfaro,
A. J. Allafort,
R. Aloisio,
J. -P. Amans,
E. Amato,
L. Ambrogi,
G. Ambrosi,
M. Ambrosio,
J. Anderson,
M. Anduze,
E. O. Angüner
, et al. (1387 additional authors not shown)
Abstract:
List of contributions from the Cherenkov Telescope Array (CTA) Consortium presented at the 6th International Symposium on High-Energy Gamma-Ray Astronomy (Gamma 2016), July 11-15, 2016, in Heidelberg, Germany.
List of contributions from the Cherenkov Telescope Array (CTA) Consortium presented at the 6th International Symposium on High-Energy Gamma-Ray Astronomy (Gamma 2016), July 11-15, 2016, in Heidelberg, Germany.
△ Less
Submitted 17 October, 2016;
originally announced October 2016.
-
Letter of Intent for KM3NeT 2.0
Authors:
S. Adrián-Martínez,
M. Ageron,
F. Aharonian,
S. Aiello,
A. Albert,
F. Ameli,
E. Anassontzis,
M. Andre,
G. Androulakis,
M. Anghinolfi,
G. Anton,
M. Ardid,
T. Avgitas,
G. Barbarino,
E. Barbarito,
B. Baret,
J. Barrios-Martí,
B. Belhorma,
A. Belias,
E. Berbee,
A. van den Berg,
V. Bertin,
S. Beurthey,
V. van Beveren,
N. Beverini
, et al. (222 additional authors not shown)
Abstract:
The main objectives of the KM3NeT Collaboration are i) the discovery and subsequent observation of high-energy neutrino sources in the Universe and ii) the determination of the mass hierarchy of neutrinos. These objectives are strongly motivated by two recent important discoveries, namely: 1) The high-energy astrophysical neutrino signal reported by IceCube and 2) the sizable contribution of elect…
▽ More
The main objectives of the KM3NeT Collaboration are i) the discovery and subsequent observation of high-energy neutrino sources in the Universe and ii) the determination of the mass hierarchy of neutrinos. These objectives are strongly motivated by two recent important discoveries, namely: 1) The high-energy astrophysical neutrino signal reported by IceCube and 2) the sizable contribution of electron neutrinos to the third neutrino mass eigenstate as reported by Daya Bay, Reno and others. To meet these objectives, the KM3NeT Collaboration plans to build a new Research Infrastructure consisting of a network of deep-sea neutrino telescopes in the Mediterranean Sea. A phased and distributed implementation is pursued which maximises the access to regional funds, the availability of human resources and the synergetic opportunities for the earth and sea sciences community. Three suitable deep-sea sites are identified, namely off-shore Toulon (France), Capo Passero (Italy) and Pylos (Greece). The infrastructure will consist of three so-called building blocks. A building block comprises 115 strings, each string comprises 18 optical modules and each optical module comprises 31 photo-multiplier tubes. Each building block thus constitutes a 3-dimensional array of photo sensors that can be used to detect the Cherenkov light produced by relativistic particles emerging from neutrino interactions. Two building blocks will be configured to fully explore the IceCube signal with different methodology, improved resolution and complementary field of view, including the Galactic plane. One building block will be configured to precisely measure atmospheric neutrino oscillations.
△ Less
Submitted 26 July, 2016; v1 submitted 27 January, 2016;
originally announced January 2016.
-
The prototype detection unit of the KM3NeT detector
Authors:
KM3NeT Collaboration,
S. Adrián-Martínez,
M. Ageron,
F. Aharonian,
S. Aiello,
A. Albert,
F. Ameli,
E. G. Anassontzis,
G. C. Androulakis,
M. Anghinolfi,
G. Anton,
S. Anvar,
M. Ardid,
T. Avgitas,
K. Balasi,
H. Band,
G. Barbarino,
E. Barbarito,
F. Barbato,
B. Baret,
S. Baron,
J. Barrios,
A. Belias,
E. Berbee,
A. M. van den Berg
, et al. (224 additional authors not shown)
Abstract:
A prototype detection unit of the KM3NeT deep-sea neutrino telescope has been installed at 3500m depth 80km offshore the Italian coast. KM3NeT in its final configuration will contain several hundreds of detection units. Each detection unit is a mechanical structure anchored to the sea floor, held vertical by a submerged buoy and supporting optical modules for the detection of Cherenkov light emitt…
▽ More
A prototype detection unit of the KM3NeT deep-sea neutrino telescope has been installed at 3500m depth 80km offshore the Italian coast. KM3NeT in its final configuration will contain several hundreds of detection units. Each detection unit is a mechanical structure anchored to the sea floor, held vertical by a submerged buoy and supporting optical modules for the detection of Cherenkov light emitted by charged secondary particles emerging from neutrino interactions. This prototype string implements three optical modules with 31 photomultiplier tubes each. These optical modules were developed by the KM3NeT Collaboration to enhance the detection capability of neutrino interactions. The prototype detection unit was operated since its deployment in May 2014 until its decommissioning in July 2015. Reconstruction of the particle trajectories from the data requires a nanosecond accuracy in the time calibration. A procedure for relative time calibration of the photomultiplier tubes contained in each optical module is described. This procedure is based on the measured coincidences produced in the sea by the 40K background light and can easily be expanded to a detector with several thousands of optical modules. The time offsets between the different optical modules are obtained using LED nanobeacons mounted inside them. A set of data corresponding to 600 hours of livetime was analysed. The results show good agreement with Monte Carlo simulations of the expected optical background and the signal from atmospheric muons. An almost background-free sample of muons was selected by filtering the time correlated signals on all the three optical modules. The zenith angle of the selected muons was reconstructed with a precision of about 3°.
△ Less
Submitted 23 December, 2015; v1 submitted 6 October, 2015;
originally announced October 2015.
-
Status and Plans for the Array Control and Data Acquisition System of the Cherenkov Telescope Array
Authors:
I. Oya,
M. Fuessling,
U. Schwanke,
P. Wegner,
A. Balzer,
D. Berge,
J. Borkowski,
J. Camprecios,
S. Colonges,
J. Colome,
C. Champion,
V. Conforti,
F. Gianotti,
T. Le Flour,
R. Lindemann,
E. Lyard,
M. Mayer,
D. Melkumyan,
M. Punch,
C. Tanci,
T. Schmidt,
J. Schwarz,
G. Tosti,
K. Verma,
A. Weinstein
, et al. (2 additional authors not shown)
Abstract:
The Cherenkov Telescope Array (CTA) is the next-generation atmospheric Cherenkov gamma-ray observatory. CTA will consist of two installations, one in the northern, and the other in the southern hemisphere, containing tens of telescopes of different sizes. The CTA performance requirements and the inherent complexity associated with the operation, control and monitoring of such a large distributed m…
▽ More
The Cherenkov Telescope Array (CTA) is the next-generation atmospheric Cherenkov gamma-ray observatory. CTA will consist of two installations, one in the northern, and the other in the southern hemisphere, containing tens of telescopes of different sizes. The CTA performance requirements and the inherent complexity associated with the operation, control and monitoring of such a large distributed multi-telescope array leads to new challenges in the field of the gamma-ray astronomy. The ACTL (array control and data acquisition) system will consist of the hardware and software that is necessary to control and monitor the CTA arrays, as well as to time-stamp, read-out, filter and store -at aggregated rates of few GB/s- the scientific data. The ACTL system must be flexible enough to permit the simultaneous automatic operation of multiple sub-arrays of telescopes with a minimum personnel effort on site. One of the challenges of the system is to provide a reliable integration of the control of a large and heterogeneous set of devices. Moreover, the system is required to be ready to adapt the observation schedule, on timescales of a few tens of seconds, to account for changing environmental conditions or to prioritize incoming scientific alerts from time-critical transient phenomena such as gamma ray bursts. This contribution provides a summary of the main design choices and plans for building the ACTL system.
△ Less
Submitted 3 September, 2015;
originally announced September 2015.
-
NectarCAM : a camera for the medium size telescopes of the Cherenkov Telescope Array
Authors:
J-F. Glicenstein,
O. Abril,
J-A. Barrio,
O. Blanch~Bigas,
J. Bolmont,
F. Bouyjou,
P. Brun,
E. Chabanne,
C. Champion,
S. Colonges,
P. Corona,
E. Delagnes,
C. Delgado,
C. Diaz Ginzov,
D. Durand,
J-P. Ernenwein,
S. Fegan,
O. Ferreira,
M. Fesquet,
A. Fiasson,
G. Fontaine,
N. Fouque,
D. Gascon,
B. Giebels,
F. Henault
, et al. (41 additional authors not shown)
Abstract:
NectarCAM is a camera proposed for the medium-sized telescopes of the Cherenkov Telescope Array (CTA) covering the central energy range of ~100 GeV to ~30 TeV. It has a modular design and is based on the NECTAr chip, at the heart of which is a GHz sampling Switched Capacitor Array and a 12-bit Analog to Digital converter. The camera will be equipped with 265 7-photomultiplier modules, covering a f…
▽ More
NectarCAM is a camera proposed for the medium-sized telescopes of the Cherenkov Telescope Array (CTA) covering the central energy range of ~100 GeV to ~30 TeV. It has a modular design and is based on the NECTAr chip, at the heart of which is a GHz sampling Switched Capacitor Array and a 12-bit Analog to Digital converter. The camera will be equipped with 265 7-photomultiplier modules, covering a field of view of 8 degrees. Each module includes the photomultiplier bases, high voltage supply, pre-amplifier, trigger, readout and Ethernet transceiver. The recorded events last between a few nanoseconds and tens of nanoseconds. The camera trigger will be flexible so as to minimize the read-out dead-time of the NECTAr chips. NectarCAM is designed to sustain a data rate of more than 4 kHz with less than 5\% dead time. The camera concept, the design and tests of the various subcomponents and results of thermal and electrical prototypes are presented. The design includes the mechanical structure, cooling of the electronics, read-out, clock distribution, slow control, data-acquisition, triggering, monitoring and services.
△ Less
Submitted 26 August, 2015;
originally announced August 2015.
-
CTA Contributions to the 34th International Cosmic Ray Conference (ICRC2015)
Authors:
The CTA Consortium,
:,
A. Abchiche,
U. Abeysekara,
Ó. Abril,
F. Acero,
B. S. Acharya,
M. Actis,
G. Agnetta,
J. A. Aguilar,
F. Aharonian,
A. Akhperjanian,
A. Albert,
M. Alcubierre,
R. Alfaro,
E. Aliu,
A. J. Allafort,
D. Allan,
I. Allekotte,
R. Aloisio,
J. -P. Amans,
E. Amato,
L. Ambrogi,
G. Ambrosi,
M. Ambrosio
, et al. (1290 additional authors not shown)
Abstract:
List of contributions from the CTA Consortium presented at the 34th International Cosmic Ray Conference, 30 July - 6 August 2015, The Hague, The Netherlands.
List of contributions from the CTA Consortium presented at the 34th International Cosmic Ray Conference, 30 July - 6 August 2015, The Hague, The Netherlands.
△ Less
Submitted 11 September, 2015; v1 submitted 24 August, 2015;
originally announced August 2015.
-
Deep sea tests of a prototype of the KM3NeT digital optical module
Authors:
S. Adrián-Martínez,
M. Ageron,
F. Aharonian,
S. Aiello,
A. Albert,
F. Ameli,
E. G. Anassontzis,
M. Anghinolfi,
G. Anton,
S. Anvar,
M. Ardid,
R. de Asmundis,
K. Balasi,
H. Band,
G. Barbarino,
E. Barbarito,
F. Barbato,
B. Baret,
S. Baron,
A. Belias,
E. Berbee,
A. M. van den Berg,
A. Berkien,
V. Bertin,
S. Beurthey
, et al. (225 additional authors not shown)
Abstract:
The first prototype of a photo-detection unit of the future KM3NeT neutrino telescope has been deployed in the deep waters of the Mediterranean Sea. This digital optical module has a novel design with a very large photocathode area segmented by the use of 31 three inch photomultiplier tubes. It has been integrated in the ANTARES detector for in-situ testing and validation. This paper reports on th…
▽ More
The first prototype of a photo-detection unit of the future KM3NeT neutrino telescope has been deployed in the deep waters of the Mediterranean Sea. This digital optical module has a novel design with a very large photocathode area segmented by the use of 31 three inch photomultiplier tubes. It has been integrated in the ANTARES detector for in-situ testing and validation. This paper reports on the first months of data taking and rate measurements. The analysis results highlight the capabilities of the new module design in terms of background suppression and signal recognition. The directionality of the optical module enables the recognition of multiple Cherenkov photons from the same $^{40}$K decay and the localization bioluminescent activity in the neighbourhood. The single unit can cleanly identify atmospheric muons and provide sensitivity to the muon arrival directions.
△ Less
Submitted 16 May, 2014; v1 submitted 5 May, 2014;
originally announced May 2014.
-
The NectarCAM camera project
Authors:
J-F. Glicenstein,
M. Barcelo,
J-A. Barrio,
O. Blanch,
J. Boix,
J. Bolmont,
C. Boutonnet,
S. Cazaux,
E. Chabanne,
C. Champion,
F. Chateau,
S. Colonges,
P. Corona,
S. Couturier,
B. Courty,
E. Delagnes,
C. Delgado,
J-P. Ernenwein,
S. Fegan,
O. Ferreira,
M. Fesquet,
G. Fontaine,
N. Fouque,
F. Henault,
D. Gascón
, et al. (35 additional authors not shown)
Abstract:
In the framework of the next generation of Cherenkov telescopes, the Cherenkov Telescope Array (CTA), NectarCAM is a camera designed for the medium size telescopes covering the central energy range of 100 GeV to 30 TeV. NectarCAM will be finely pixelated (~ 1800 pixels for a 8 degree field of view, FoV) in order to image atmospheric Cherenkov showers by measuring the charge deposited within a few…
▽ More
In the framework of the next generation of Cherenkov telescopes, the Cherenkov Telescope Array (CTA), NectarCAM is a camera designed for the medium size telescopes covering the central energy range of 100 GeV to 30 TeV. NectarCAM will be finely pixelated (~ 1800 pixels for a 8 degree field of view, FoV) in order to image atmospheric Cherenkov showers by measuring the charge deposited within a few nanoseconds time-window. It will have additional features like the capacity to record the full waveform with GHz sampling for every pixel and to measure event times with nanosecond accuracy. An array of a few tens of medium size telescopes, equipped with NectarCAMs, will achieve up to a factor of ten improvement in sensitivity over existing instruments in the energy range of 100 GeV to 10 TeV. The camera is made of roughly 250 independent read-out modules, each composed of seven photo-multipliers, with their associated high voltage base and control, a read-out board and a multi-service backplane board. The read-out boards use NECTAr (New Electronics for the Cherenkov Telescope Array) ASICs which have the dual functionality of analogue memories and Analogue to Digital Converter (ADC). The camera trigger to be used will be flexible so as to minimize the read-out dead-time of the NECTAr chips. We present the camera concept and the design and tests of the various subcomponents. The design includes the mechanical parts, the cooling of the electronics, the readout, the data acquisition, the trigger, the monitoring and services.
△ Less
Submitted 17 July, 2013;
originally announced July 2013.
-
CTA contributions to the 33rd International Cosmic Ray Conference (ICRC2013)
Authors:
The CTA Consortium,
:,
O. Abril,
B. S. Acharya,
M. Actis,
G. Agnetta,
J. A. Aguilar,
F. Aharonian,
M. Ajello,
A. Akhperjanian,
M. Alcubierre,
J. Aleksic,
R. Alfaro,
E. Aliu,
A. J. Allafort,
D. Allan,
I. Allekotte,
R. Aloisio,
E. Amato,
G. Ambrosi,
M. Ambrosio,
J. Anderson,
E. O. Angüner,
L. A. Antonelli,
V. Antonuccio
, et al. (1082 additional authors not shown)
Abstract:
Compilation of CTA contributions to the proceedings of the 33rd International Cosmic Ray Conference (ICRC2013), which took place in 2-9 July, 2013, in Rio de Janeiro, Brazil
Compilation of CTA contributions to the proceedings of the 33rd International Cosmic Ray Conference (ICRC2013), which took place in 2-9 July, 2013, in Rio de Janeiro, Brazil
△ Less
Submitted 29 July, 2013; v1 submitted 8 July, 2013;
originally announced July 2013.
