-
Production and Integration of the ATLAS Insertable B-Layer
Authors:
B. Abbott,
J. Albert,
F. Alberti,
M. Alex,
G. Alimonti,
S. Alkire,
P. Allport,
S. Altenheiner,
L. Ancu,
E. Anderssen,
A. Andreani,
A. Andreazza,
B. Axen,
J. Arguin,
M. Backhaus,
G. Balbi,
J. Ballansat,
M. Barbero,
G. Barbier,
A. Bassalat,
R. Bates,
P. Baudin,
M. Battaglia,
T. Beau,
R. Beccherle
, et al. (352 additional authors not shown)
Abstract:
During the shutdown of the CERN Large Hadron Collider in 2013-2014, an additional pixel layer was installed between the existing Pixel detector of the ATLAS experiment and a new, smaller radius beam pipe. The motivation for this new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the robustness and performance of the ATLAS tracking system, given the higher instantaneous and i…
▽ More
During the shutdown of the CERN Large Hadron Collider in 2013-2014, an additional pixel layer was installed between the existing Pixel detector of the ATLAS experiment and a new, smaller radius beam pipe. The motivation for this new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the robustness and performance of the ATLAS tracking system, given the higher instantaneous and integrated luminosities realised following the shutdown. Because of the extreme radiation and collision rate environment, several new radiation-tolerant sensor and electronic technologies were utilised for this layer. This paper reports on the IBL construction and integration prior to its operation in the ATLAS detector.
△ Less
Submitted 6 June, 2018; v1 submitted 2 March, 2018;
originally announced March 2018.
-
Results of the 2015 testbeam of a 180 nm AMS High-Voltage CMOS sensor prototype
Authors:
M. Benoit,
J. Bilbao de Mendizabal,
G. Casse,
H. Chen,
K. Chen,
F. A. Di Bello,
D. Ferrere,
T. Golling,
S. Gonzalez-Sevilla,
G. Iacobucci,
F. Lanni,
H. Liu,
F. Meloni,
L. Meng,
A. Miucci,
D. Muenstermann,
M. Nessi,
I. Peric,
M. Rimoldi,
B. Ristic,
M. Vicente Barrero Pinto,
J. Vossebeld,
M. Weber,
W. Wu,
L. Xu
Abstract:
Active pixel sensors based on the High-Voltage CMOS technology are being investigated as a viable option for the future pixel tracker of the ATLAS experiment at the High-Luminosity LHC. This paper reports on the testbeam measurements performed at the H8 beamline of the CERN Super Proton Synchrotron on a High-Voltage CMOS sensor prototype produced in 180 nm AMS technology. Results in terms of track…
▽ More
Active pixel sensors based on the High-Voltage CMOS technology are being investigated as a viable option for the future pixel tracker of the ATLAS experiment at the High-Luminosity LHC. This paper reports on the testbeam measurements performed at the H8 beamline of the CERN Super Proton Synchrotron on a High-Voltage CMOS sensor prototype produced in 180 nm AMS technology. Results in terms of tracking efficiency and timing performance, for different threshold and bias conditions, are shown.
△ Less
Submitted 30 June, 2016; v1 submitted 24 March, 2016;
originally announced March 2016.
-
The FE-I4 Telescope for particle tracking in testbeam experiments
Authors:
M. Benoit,
J. Bilbao De Mendizabal,
F. A. Di Bello,
D. Ferrere,
T. Golling,
S. Gonzalez-Sevilla,
G. Iacobucci,
M. Kocian,
D. Muenstermann,
B. Ristic,
A. Sciuccati
Abstract:
A testbeam telescope, based on ATLAS IBL silicon pixel modules, has been built. It comprises six planes of planar silicon sensors with 250 x 50 um^2 pitch, read out by ATLAS FE-I4 chips. In the CERN SPS H8 beamline (180 GeV pi+) a resolution of better than 8 x 12 um^2 at the position of the device under test was achieved. The telescope reached a trigger rate of 6kHz with two measured devices. It i…
▽ More
A testbeam telescope, based on ATLAS IBL silicon pixel modules, has been built. It comprises six planes of planar silicon sensors with 250 x 50 um^2 pitch, read out by ATLAS FE-I4 chips. In the CERN SPS H8 beamline (180 GeV pi+) a resolution of better than 8 x 12 um^2 at the position of the device under test was achieved. The telescope reached a trigger rate of 6kHz with two measured devices. It is mainly designed for studies using FE-I4 based prototypes, but has also been successfully run with independent DAQ systems. Specialised trigger schemes ensure data synchronisation between these external devices and the telescope. A region-of-interest trigger can be formed by setting masks on the first and the last pixel sensor planes. The setup infrastructure provides centrally controlled and monitored high and low voltage power supplies, silicon oil cooling, temperature and humidity sensors and movable stages.
△ Less
Submitted 20 June, 2016; v1 submitted 24 March, 2016;
originally announced March 2016.
