Showing 1–8 of 8 results for author: Voelker, J

Modeling of Surface Damage at the Si/SiO$_2$-interface of Irradiated MOS-capacitors

Authors: N. Akchurin, G. Altopp, B. Burkle, W. D. Frey, U. Heintz, N. Hinton, M. Hoeferkamp, Y. Kazhykarim, V. Kuryatkov, T. Mengke, T. Peltola, S. Seidel, E. Spencer, M. Tripathi, J. Voelker

Abstract: Surface damage caused by ionizing radiation in SiO$_2$ passivated silicon particle detectors consists mainly of the accumulation of a positively charged layer along with trapped-oxide-charge and interface traps inside the oxide and close to the Si/SiO$_2$-interface. High density positive interface net charge can be detrimental to the operation of a multi-channel $n$-on-$p$ sensor since the inversi… ▽ More Surface damage caused by ionizing radiation in SiO$_2$ passivated silicon particle detectors consists mainly of the accumulation of a positively charged layer along with trapped-oxide-charge and interface traps inside the oxide and close to the Si/SiO$_2$-interface. High density positive interface net charge can be detrimental to the operation of a multi-channel $n$-on-$p$ sensor since the inversion layer generated under the Si/SiO$_2$-interface can cause loss of position resolution by creating a conduction channel between the electrodes. In the investigation of the radiation-induced accumulation of oxide charge and interface traps, a capacitance-voltage characterization study of n/$γ$- and $γ$-irradiated Metal-Oxide-Semiconductor (MOS) capacitors showed that close agreement between measurement and simulation were possible when oxide charge density was complemented by both acceptor- and donor-type deep interface traps with densities comparable to the oxide charges. Corresponding inter-strip resistance simulations of a $n$-on-$p$ sensor with the tuned oxide charge density and interface traps show close agreement with experimental results. The beneficial impact of radiation-induced accumulation of deep interface traps on inter-electrode isolation may be considered in the optimization of the processing parameters of isolation implants on $n$-on-$p$ sensors for the extreme radiation environments. △ Less

Submitted 1 August, 2023; v1 submitted 23 May, 2023; originally announced May 2023.

Comments: Corresponding author: T. Peltola. 24 pages, 17 figures, 6 tables

Report number: APDL-2023-001

Journal ref: JINST 18 P08001 (2023)

The Physical Properties of Low-Redshift FeLoBAL Quasars: II. The Rest-Frame Optical Emission Line Properties

Authors: Karen M. Leighly, Hyunseop Choi, Cora DeFrancesco, Julianna Voelker, Donald M. Terndrup, Sarah C. Gallagher, Gordon T. Richards

Abstract: We report the results of analysis of the Hbeta emission-line region of a sample of thirty low-redshift (z<1) iron low-ionization broad absorption line quasars (FeLoBALQs). Eleven of these objects are newly classified as FeLoBALQs. A matched sample of 132 unabsorbed quasars was analyzed in parallel. The emission lines showed the well known anticorrelation between the [OIII] and FeII emission (Boros… ▽ More We report the results of analysis of the Hbeta emission-line region of a sample of thirty low-redshift (z<1) iron low-ionization broad absorption line quasars (FeLoBALQs). Eleven of these objects are newly classified as FeLoBALQs. A matched sample of 132 unabsorbed quasars was analyzed in parallel. The emission lines showed the well known anticorrelation between the [OIII] and FeII emission (Boroson & Green 1992). Using a summary statistic called E1 to quantify this anticorrelation, we found that while the distribution of E1 for the unabsorbed quasars has a single peak, the FeLoBALQs have a bimodal shape in this parameter. Previous studies have shown that the line emission properties of BAL and non-BAL quasars are consistent, and therefore the difference in the Hbeta region emission between FeLoBAL quasars and unabsorbed quasars is a new result. The two populations of FeLoBAL quasars are characterized by low and high bolometric luminosities and Eddington ratios. Some previous studies have suggested that BAL quasars are high accretion-rate objects, and therefore the discovery of the low accretion-rate branch of FeLoBAL quasars was unexpected. We also found that the Hbeta FWHM is systematically broader among the FeLoBALQs compared with the non-BAL quasars implying a higher inclination viewing angle or a dearth of low-velocity line-emitting gas. △ Less

Submitted 25 May, 2022; originally announced May 2022.

Comments: Resubmitted to ApJ after review

Optimizing a Superconducting Radiofrequency Gun Using Deep Reinforcement Learning

Authors: David Meier, Luis Vera Ramirez, Jens Völker, Bernhard Sick, Jens Viefhaus, Gregor Hartmann

Abstract: Superconducting photoelectron injectors are a promising technique for generating high brilliant pulsed electron beams with high repetition rates and low emittances. Experiments such as ultra-fast electron diffraction, experiments at the Terahertz scale, and energy recovery linac applications require such properties. However, optimization of the beam properties is challenging due to the high amount… ▽ More Superconducting photoelectron injectors are a promising technique for generating high brilliant pulsed electron beams with high repetition rates and low emittances. Experiments such as ultra-fast electron diffraction, experiments at the Terahertz scale, and energy recovery linac applications require such properties. However, optimization of the beam properties is challenging due to the high amount of possible machine parameter combinations. In this article, we show the successful automated optimization of beam properties utilizing an already existing simulation model. To reduce the amount of required computation time, we replace the costly simulation by a faster approximation with a neural network. For optimization, we propose a reinforcement learning approach leveraging the simple computation of the derivative of the approximation. We prove that our approach outperforms common optimization methods for the required function evaluations given a defined minimum accuracy. △ Less

Submitted 11 March, 2022; originally announced March 2022.

Response of a CMS HGCAL silicon-pad electromagnetic calorimeter prototype to 20-300 GeV positrons

Authors: B. Acar, G. Adamov, C. Adloff, S. Afanasiev, N. Akchurin, B. Akgün, F. Alam Khan, M. Alhusseini, J. Alison, A. Alpana, G. Altopp, M. Alyari, S. An, S. Anagul, I. Andreev, P. Aspell, I. O. Atakisi, O. Bach, A. Baden, G. Bakas, A. Bakshi, S. Bannerjee, P. Bargassa, D. Barney, F. Beaudette , et al. (364 additional authors not shown)

Abstract: The Compact Muon Solenoid Collaboration is designing a new high-granularity endcap calorimeter, HGCAL, to be installed later this decade. As part of this development work, a prototype system was built, with an electromagnetic section consisting of 14 double-sided structures, providing 28 sampling layers. Each sampling layer has an hexagonal module, where a multipad large-area silicon sensor is glu… ▽ More The Compact Muon Solenoid Collaboration is designing a new high-granularity endcap calorimeter, HGCAL, to be installed later this decade. As part of this development work, a prototype system was built, with an electromagnetic section consisting of 14 double-sided structures, providing 28 sampling layers. Each sampling layer has an hexagonal module, where a multipad large-area silicon sensor is glued between an electronics circuit board and a metal baseplate. The sensor pads of approximately 1 cm$^2$ are wire-bonded to the circuit board and are readout by custom integrated circuits. The prototype was extensively tested with beams at CERN's Super Proton Synchrotron in 2018. Based on the data collected with beams of positrons, with energies ranging from 20 to 300 GeV, measurements of the energy resolution and linearity, the position and angular resolutions, and the shower shapes are presented and compared to a detailed Geant4 simulation. △ Less

Submitted 31 March, 2022; v1 submitted 12 November, 2021; originally announced November 2021.

Construction and commissioning of CMS CE prototype silicon modules

Authors: B. Acar, G. Adamov, C. Adloff, S. Afanasiev, N. Akchurin, B. Akgün, M. Alhusseini, J. Alison, G. Altopp, M. Alyari, S. An, S. Anagul, I. Andreev, M. Andrews, P. Aspell, I. A. Atakisi, O. Bach, A. Baden, G. Bakas, A. Bakshi, P. Bargassa, D. Barney, E. Becheva, P. Behera, A. Belloni , et al. (307 additional authors not shown)

Abstract: As part of its HL-LHC upgrade program, the CMS Collaboration is develo** a High Granularity Calorimeter (CE) to replace the existing endcap calorimeters. The CE is a sampling calorimeter with unprecedented transverse and longitudinal readout for both electromagnetic (CE-E) and hadronic (CE-H) compartments. The calorimeter will be built with $\sim$30,000 hexagonal silicon modules. Prototype modul… ▽ More As part of its HL-LHC upgrade program, the CMS Collaboration is develo** a High Granularity Calorimeter (CE) to replace the existing endcap calorimeters. The CE is a sampling calorimeter with unprecedented transverse and longitudinal readout for both electromagnetic (CE-E) and hadronic (CE-H) compartments. The calorimeter will be built with $\sim$30,000 hexagonal silicon modules. Prototype modules have been constructed with 6-inch hexagonal silicon sensors with cell areas of 1.1~$cm^2$, and the SKIROC2-CMS readout ASIC. Beam tests of different sampling configurations were conducted with the prototype modules at DESY and CERN in 2017 and 2018. This paper describes the construction and commissioning of the CE calorimeter prototype, the silicon modules used in the construction, their basic performance, and the methods used for their calibration. △ Less

Submitted 10 December, 2020; originally announced December 2020.

Comments: 35 pages, submitted to JINST

The DAQ system of the 12,000 Channel CMS High Granularity Calorimeter Prototype

Authors: B. Acar, G. Adamov, C. Adloff, S. Afanasiev, N. Akchurin, B. Akgün, M. Alhusseini, J. Alison, G. Altopp, M. Alyari, S. An, S. Anagul, I. Andreev, M. Andrews, P. Aspell, I. A. Atakisi, O. Bach, A. Baden, G. Bakas, A. Bakshi, P. Bargassa, D. Barney, E. Becheva, P. Behera, A. Belloni , et al. (307 additional authors not shown)

Abstract: The CMS experiment at the CERN LHC will be upgraded to accommodate the 5-fold increase in the instantaneous luminosity expected at the High-Luminosity LHC (HL-LHC). Concomitant with this increase will be an increase in the number of interactions in each bunch crossing and a significant increase in the total ionising dose and fluence. One part of this upgrade is the replacement of the current endca… ▽ More The CMS experiment at the CERN LHC will be upgraded to accommodate the 5-fold increase in the instantaneous luminosity expected at the High-Luminosity LHC (HL-LHC). Concomitant with this increase will be an increase in the number of interactions in each bunch crossing and a significant increase in the total ionising dose and fluence. One part of this upgrade is the replacement of the current endcap calorimeters with a high granularity sampling calorimeter equipped with silicon sensors, designed to manage the high collision rates. As part of the development of this calorimeter, a series of beam tests have been conducted with different sampling configurations using prototype segmented silicon detectors. In the most recent of these tests, conducted in late 2018 at the CERN SPS, the performance of a prototype calorimeter equipped with ${\approx}12,000\rm{~channels}$ of silicon sensors was studied with beams of high-energy electrons, pions and muons. This paper describes the custom-built scalable data acquisition system that was built with readily available FPGA mezzanines and low-cost Raspberry PI computers. △ Less

Submitted 8 December, 2020; v1 submitted 7 December, 2020; originally announced December 2020.

Charge Collection and Electrical Characterization of Neutron Irradiated Silicon Pad Detectors for the CMS High Granularity Calorimeter

Authors: N. Akchurin, P. Almeida, G. Altopp, M. Alyari, T. Bergauer, E. Brondolin, B. Burkle, W. D. Frey, Z. Gecse, U. Heintz, N. Hinton, V. Kuryatkov, R. Lipton, M. Mannelli, T. Mengke, P. Paulitsch, T. Peltola, F. Pitters, E. Sicking, E. Spencer, M. Tripathi, M. Vicente Barreto Pinto, J. Voelker, Z. Wang, R. Yohay

Abstract: The replacement of the existing endcap calorimeter in the Compact Muon Solenoid (CMS) detector for the high-luminosity LHC (HL-LHC), scheduled for 2027, will be a high granularity calorimeter. It will provide detailed position, energy, and timing information on electromagnetic and hadronic showers in the immense pileup of the HL-LHC. The High Granularity Calorimeter (HGCAL) will use 120-, 200-, an… ▽ More The replacement of the existing endcap calorimeter in the Compact Muon Solenoid (CMS) detector for the high-luminosity LHC (HL-LHC), scheduled for 2027, will be a high granularity calorimeter. It will provide detailed position, energy, and timing information on electromagnetic and hadronic showers in the immense pileup of the HL-LHC. The High Granularity Calorimeter (HGCAL) will use 120-, 200-, and 300-$μ\textrm{m}$ thick silicon (Si) pad sensors as the main active material and will sustain 1-MeV neutron equivalent fluences up to about $10^{16}~\textrm{n}_\textrm{eq}\textrm{cm}^{-2}$. In order to address the performance degradation of the Si detectors caused by the intense radiation environment, irradiation campaigns of test diode samples from 8-inch and 6-inch wafers were performed in two reactors. Characterization of the electrical and charge collection properties after irradiation involved both bulk polarities for the three sensor thicknesses. Since the Si sensors will be operated at -30 $^\circ$C to reduce increasing bulk leakage current with fluence, the charge collection investigation of 30 irradiated samples was carried out with the infrared-TCT setup at -30 $^\circ$C. TCAD simulation results at the lower fluences are in close agreement with the experimental results and provide predictions of sensor performance for the lower fluence regions not covered by the experimental study. All investigated sensors display 60$\%$ or higher charge collection efficiency at their respective highest lifetime fluences when operated at 800 V, and display above 90$\%$ at the lowest fluence, at 600 V. The collected charge close to the fluence of $10^{16}~\textrm{n}_\textrm{eq}\textrm{cm}^{-2}$ exceeds 1 fC at voltages beyond 800 V. △ Less

Submitted 4 August, 2020; v1 submitted 16 May, 2020; originally announced May 2020.

Comments: 36 pages, 34 figures

Scientific opportunies for bERLinPro 2020+, report with ideas and conclusions from bERLinProCamp 2019

Authors: Thorsten Kamps, Michael Abo-Bakr, Andreas Adelmann, Kevin Andre, Deepa Angal-Kalinin, Felix Armborst, Andre Arnold, Michaela Arnold, Raymond Amador, Stephen Benson, Yulia Choporova, Illya Drebot, Ralph Ernstdorfer, Pavel Evtushenko, Kathrin Goldammer, Andreas Jankowiak, Georg Hofftstaetter, Florian Hug, Ji-Gwang Hwang, Lee Jones, Julius Kuehn, Jens Knobloch, Bettina Kuske, Andre Lampe, Sonal Mistry , et al. (16 additional authors not shown)

Abstract: The Energy Recovery Linac (ERL) paradigm offers the promise to generate intense electron beams of superior quality with extremely small six-dimensional phase space for many applications in the physical sciences, materials science, chemistry, health, information technology and security. Helmholtz-Zentrum Berlin started in 2010 an intensive R\&D programme to address the challenges related to the ERL… ▽ More The Energy Recovery Linac (ERL) paradigm offers the promise to generate intense electron beams of superior quality with extremely small six-dimensional phase space for many applications in the physical sciences, materials science, chemistry, health, information technology and security. Helmholtz-Zentrum Berlin started in 2010 an intensive R\&D programme to address the challenges related to the ERL as driver for future light sources by setting up the bERLinPro (Berlin ERL Project) ERL with 50 MeV beam energy and high average current. The project is close to reach its major milestone in 2020, acceleration and recovery of a high brightness electron beam. The goal of bERLinProCamp 2019 was to discuss scientific opportunities for bERLinPro 2020+. bERLinProCamp 2019 was held on Tue, 17.09.2019 at Helmholtz-Zentrum Berlin, Berlin, Germany. This paper summarizes the main themes and output of the workshop. △ Less

Submitted 8 January, 2020; v1 submitted 2 October, 2019; originally announced October 2019.