-
The influence of dislocations on R-phase transformations in a NiTi shape memory alloy
Authors:
Himanshu Vashishtha,
David M. Collins
Abstract:
The ability to control the stress-induced phase transformation of the shape memory alloy, NiTi, is an important technological challenge that must be understood for their wide application in devices that can exploit their reversible strain properties. This study elucidates the direct relationship between dislocation density and the \textit{R}-phase transformation, including its formation temperatur…
▽ More
The ability to control the stress-induced phase transformation of the shape memory alloy, NiTi, is an important technological challenge that must be understood for their wide application in devices that can exploit their reversible strain properties. This study elucidates the direct relationship between dislocation density and the \textit{R}-phase transformation, including its formation temperature from interrupted annealing of rolled NiTi samples. Deformation is shown to determine the enthalpy change required for the B2$\rightarrow$\textit{R}-phase transformation, with associated transformation temperatures being modifiable via dislocation density and recovery processes. Recovery is shown to be rapid, highly heterogeneous and sensitive to crystal orientation. Grains with a $\langle100\rangle$ direction close to the macroscopic rolling direction recover more rapidly than $\langle110\rangle$ and $\langle111\rangle$ orientated grains. Considered to be governed by processing induced residual stresses and resultant crystallographic dependent annihilation/slip pathways, there are opportunities to tune B2$\rightarrow$\textit{R}-phase transformation on either a grain-averaged or an orientation dependant per-grain basis.
△ Less
Submitted 18 June, 2024;
originally announced June 2024.
-
A micromechanical study of heat treatment induced hardening in α-brass
Authors:
Jonathan Birch,
Emily Jenkins,
Anastasia Vrettou,
Mohammed Said,
Himanshu Vashishtha,
Thomas Connolley,
Jeff Brooks,
David M. Collins
Abstract:
The mechanisms that govern a previously unexplained hardening effect of a single phase Cu-30wt%Zn α-brass after heating have been investigated. After cold-work, the alloy possesses an increased yield strength and hardening rate only when heat treated to temperatures close to 220{^\circ}C, and is otherwise softer. Crystallographic texture and microstructure, explored using electron backscatter diff…
▽ More
The mechanisms that govern a previously unexplained hardening effect of a single phase Cu-30wt%Zn α-brass after heating have been investigated. After cold-work, the alloy possesses an increased yield strength and hardening rate only when heat treated to temperatures close to 220{^\circ}C, and is otherwise softer. Crystallographic texture and microstructure, explored using electron backscatter diffraction (EBSD), describe the deformation heterogeneity including twin development, as a function of heat treatment. When heated, an increased area fraction of deformation twins is observed, with dimensions reaching a critical size that maximises the resistance to dislocation slip in the parent grains. The effect is shown to dominate over other alloy characteristics including short range order, giving serrated yielding during tensile testing which is mostly eliminated after heating. In-situ X-ray diffraction during tensile testing corroborates these findings; dislocation-related line broadening and lattice strain development between as worked and heated α-brass is directly related to the interaction between the dislocations and the population of deformation twins. The experiments unambiguously disprove that other thermally-induced microstructure features contribute to thermal hardening. Specifically, the presence of recrystallised grains or second phases do not play a role. As these heat treatments match annealing conditions subjected to α-brass during deformation-related manufacturing processes, the results here are considered critical to understand, predict and exploit, where appropriate, any beneficial process-induced structural behaviour.
△ Less
Submitted 14 June, 2024;
originally announced June 2024.
-
Microscale stress-geometry interactions in an additively manufactured NiTi cardiovascular stent: A synchrotron dual imaging tomography and diffraction study
Authors:
Himanshu Vashishtha,
Parastoo Jamshidi,
Anastasia Vrettou,
Anna Kareer,
Michael Goode,
Hans Deyhle,
Andrew James,
Sharif Ahmad,
Christina Reinhard,
Moataz M. Attallah,
David M. Collins
Abstract:
This study explores cardiovascular stents fabricated using laser powder bed fusion (LPBF); an emerging method to offer patient-specific customisable parts. Here, the shape memory alloy NiTi, in a near equiatomic composition, was investigated to deconvolve the material response from macroscopic component effects. Specifically, stress-geometry interactions were revealed, in-situ, for a minaturised c…
▽ More
This study explores cardiovascular stents fabricated using laser powder bed fusion (LPBF); an emerging method to offer patient-specific customisable parts. Here, the shape memory alloy NiTi, in a near equiatomic composition, was investigated to deconvolve the material response from macroscopic component effects. Specifically, stress-geometry interactions were revealed, in-situ, for a minaturised cardiovascular stent subjected to an externally applied cylindrical stress whilst acquiring synchrotron X-ray imaging and diffraction data. The approach enabled the collection of spatially resolved micromechanical deformation data; the formation of stress-induced martensite and R-phase was evident, occurring in locations near junctions between stent ligaments where stress concentrations exist. In the as-fabricated condition, hardness maps were obtained through nanoindentation, demonstrating that the localised deformation and deformation patterning is further controlled by porosity and microstructural heterogeneity. Electron backscatter diffraction (EBSD) supported these observations, showing a finer grain structure near stent junctions with higher associated lattice curvature. These features, combined with stress concentrations when loaded will initiate localised phase transformations. If the stent was subjected to repeated loading, representing in-vivo conditions, these regions would be susceptible to cyclic damage through transformation memory loss, leading to premature component failure. This study highlights the challenges that must be addressed for the post-processing treatment of LABF-processed stents for healthcare-related applications.
△ Less
Submitted 12 December, 2023;
originally announced December 2023.
-
Grain-level effects on in-situ deformation-induced phase transformations in a complex-phase steel using 3DXRD and EBSD
Authors:
James A. D. Ball,
Claire Davis,
Carl Slater,
Himanshu Vashishtha,
Mohammed Said,
Louis Hébrard,
Florian Steinhilber,
Jonathan P. Wright,
Thomas Connolley,
Stefan Michalik,
David M. Collins
Abstract:
A novel complex-phase steel alloy is conceived with a deliberately unstable austenite, $γ$, phase that enables the deformation-induced martensitic transformations (DIMT) to be explored at low levels of plastic strain. The DIMT was thus explored, in-situ and non-destructively, using both far-field Three-Dimensional X-Ray Diffraction (3DXRD) and Electron Back-Scatter Diffraction (EBSD). Substantial…
▽ More
A novel complex-phase steel alloy is conceived with a deliberately unstable austenite, $γ$, phase that enables the deformation-induced martensitic transformations (DIMT) to be explored at low levels of plastic strain. The DIMT was thus explored, in-situ and non-destructively, using both far-field Three-Dimensional X-Ray Diffraction (3DXRD) and Electron Back-Scatter Diffraction (EBSD). Substantial $α'$ martensite formation was observed under 10% applied strain with EBSD, and many $\varepsilon$ grain formation events were captured with 3DXRD, indicative of the indirect transformation of martensite via the reaction $γ\rightarrow \varepsilon \rightarrow α'$. Using $\varepsilon$ grain formation as a direct measurement of $γ$ grain stability, the influence of several microstructural properties, such as grain size, orientation and neighbourhood configuration, on $γ$ stability have been identified. Larger $γ$ grains were found to be less stable than smaller grains. Any $γ$ grains oriented with {100} parallel to the loading direction preferentially transformed with lower stresses. Parent $\varepsilon$-forming $γ$ grains possessed a neighbourhood with increased ferritic/martensitic volume fraction. This finding shows, unambiguously, that $α$/$α'$ promotes $\varepsilon$ formation in neighbouring grains. The minimum strain work criterion model for $\varepsilon$ variant prediction was also evaluated, which worked well for most grains. However, $\varepsilon$-forming grains with a lower stress were less well predicted by the model, indicating crystal-level behaviour must be considered for accurate $\varepsilon$ formation. The findings from this work are considered key for the future design of alloys where the deformation response can be controlled by tailoring microstructure and local or macroscopic crystal orientations.
△ Less
Submitted 7 November, 2023; v1 submitted 6 November, 2023;
originally announced November 2023.
-
Registration between DCT and EBSD datasets for multiphase microstructures
Authors:
James A. D. Ball,
Jette Oddershede,
Claire Davis,
Carl Slater,
Mohammed Said,
Himanshu Vashishtha,
Stefan Michalik,
David M. Collins
Abstract:
The ability to characterise the three-dimensional microstructure of multiphase materials is essential for understanding the interaction between phases and associated materials properties. Here, laboratory-based diffraction-contrast tomography (DCT), a recently-established materials characterization technique that can determine grain phases, morphologies, positions and orientations in a voxel-based…
▽ More
The ability to characterise the three-dimensional microstructure of multiphase materials is essential for understanding the interaction between phases and associated materials properties. Here, laboratory-based diffraction-contrast tomography (DCT), a recently-established materials characterization technique that can determine grain phases, morphologies, positions and orientations in a voxel-based reconstruction method, was used to map part of a dual-phase steel alloy sample. To assess the resulting microstructures that were produced by the DCT technique, an EBSD map was collected within the same sample volume. To identify the 2D slice of the 3D DCT reconstruction that best corresponded to the EBSD map, a novel registration technique based solely on grain-averaged orientations was developed -- this registration technique requires very little a priori knowledge of dataset alignment and can be extended to other techniques that only recover grain-averaged orientation data such as far-field 3D X-ray diffraction microscopy. Once the corresponding 2D slice was identified in the DCT dataset, comparisons of phase balance, grain size, shape and texture were performed between DCT and EBSD techniques. More complicated aspects of the microstructural morphology such as grain boundary shape and grains less than a critical size were poorly reproduced by the DCT reconstruction, primarily due to the difference in resolutions of the technique compared with EBSD. However, lab-based DCT is shown to accurately determine the centre-of-mass position, orientation, and size of the large grains for each phase present, austenite and martensitic ferrite. The results reveals a complex ferrite grain network of similar crystal orientations that are absent from the EBSD dataset. Such detail demonstrates that lab-based DCT, as a technique, shows great promise in the field of multi-phase material characterization.
△ Less
Submitted 29 June, 2023;
originally announced June 2023.
