-
Anomalous softness in amorphous matter in the reversible plastic regime
Authors:
Ahmed Elgailani,
Damien Vandembroucq,
Craig Maloney
Abstract:
We study an integer automaton elasto-plastic model of an amorphous solid subject to cyclic shear of amplitude $Γ$. We focus on the reversible plastic regime at intermediate $Γ_0<Γ<Γ_y$, where, after a transient, the system settles into a periodic limit cycle with hysteretic, dissipative plastic events which repeat after an integer number of cycles. We study the plastic strain rate,…
▽ More
We study an integer automaton elasto-plastic model of an amorphous solid subject to cyclic shear of amplitude $Γ$. We focus on the reversible plastic regime at intermediate $Γ_0<Γ<Γ_y$, where, after a transient, the system settles into a periodic limit cycle with hysteretic, dissipative plastic events which repeat after an integer number of cycles. We study the plastic strain rate, $\frac{dε}{dγ}$, (where $γ$ is the applied strain and $ε$ is the plastic strain) during the terminal limit cycles and show that it consists of a cree** regime at low $γ$ with very low $\frac{dε}{dγ}$ followed by a sharp transition at a characteristic strain, $γ_*$, and stress, $σ_*$, to a flowing regime with higher $\frac{dε}{dγ}$. We show that while increasing $Γ$ above $Γ_0$ results in lower terminal ground state energy, $U_{\text{min}}$, and a correspondingly narrower distribution of stresses, it, surprisingly, results in lower $γ_*$, and $σ_*$. The stress distribution, $P(σ)$, also becomes skewed for $Γ>Γ_0$. That is, the systems in the RPR are anomalously soft and mechanically polarized. We relate this to an emergent characteristic feature in the stress distribution, $P(σ)$, at a value, $σ_0$, which is independent of $Γ$ and show that $σ_0$ implies a relation between the $Γ$ dependence of $σ_*$, $γ_*$, and the amplitude of plastic strain, $ε_p$. We show that the onset of hysteresis is characterized by a power-law scaling, indicative of a second order transition with $ε_p\propto (Γ-Γ_0)^{1.2\pm0.1}$. We argue that $σ_0$ and, correspondingly, the onset of the RPR at $Γ=Γ_0$, is simply set by the so-called Eshelby-stress. Furthermore, we show that cycling at $Γ_0$ results in a maximally hardened state.
△ Less
Submitted 20 December, 2022;
originally announced December 2022.
-
Coarse-graining amorphous plasticity: impact of rejuvenation and disorder
Authors:
Botond Tyukodi,
Armand Barbot,
Reinaldo Garciá-Garciá,
Matthias Lerbinger,
Sylvain Patinet,
Damien Vandembroucq
Abstract:
The coarse-graining of amorphous plasticity from the atomistic to the mesoscopic scale is studied in the framework of a simple scalar elasto-plastic model. Building on recent results obtained on the atomistic scale, we discuss the interest in a disordered landscape-informed threshold disorder to reproduce the physics of amorphous plasticity. We show that accounting for a rejuvenation scenario allo…
▽ More
The coarse-graining of amorphous plasticity from the atomistic to the mesoscopic scale is studied in the framework of a simple scalar elasto-plastic model. Building on recent results obtained on the atomistic scale, we discuss the interest in a disordered landscape-informed threshold disorder to reproduce the physics of amorphous plasticity. We show that accounting for a rejuvenation scenario allows us to reproduce quasi-quantitatively the evolution of the mean local yield stress and the localization behavior. We emphasize the crucial role of two dimensionless parameters: the relative strength of the yield stress disorder with respect to the typical stress drops associated with a plastic rearrangement, and the age parameter characterizing the relative stability of the initial glass with respect to the rejuvenated glass that emerges upon shear deformation.
△ Less
Submitted 30 August, 2022;
originally announced August 2022.
-
Hollow-core fibers with reduced surface roughness and ultralow loss in the short-wavelength range
Authors:
Jonas H. Osório,
Foued Amrani,
Frédéric Delahaye,
Ali Dhaybi,
Kostiantyn Vasko,
Fabio Giovanardi,
Damien Vandembroucq,
Gilles Tessier,
Luca Vincetti,
Benoît Debord,
Frédéric Gérôme,
Fetah Benabid
Abstract:
While optical fibers display excellent performances in the infrared, visible and ultraviolet ranges remain poorly addressed by them. Obtaining better fibers for the short-wavelength range has been restricted, in all fiber optics, by scattering processes. In hollow-core fibers, the scattering loss arises from the core roughness and represents the limiting factor in reducing their loss regardless of…
▽ More
While optical fibers display excellent performances in the infrared, visible and ultraviolet ranges remain poorly addressed by them. Obtaining better fibers for the short-wavelength range has been restricted, in all fiber optics, by scattering processes. In hollow-core fibers, the scattering loss arises from the core roughness and represents the limiting factor in reducing their loss regardless of the fiber cladding confinement power. To attain fibers performing at short wavelengths, it is paramount develo** means to minimize the height variations on the fiber microstructure boundaries. Here, we report on the reduction of the core surface roughness of hollow-core fibers by modifying their fabrication technique. In the novel process proposed herein, counter directional gas fluxes are applied within the fiber holes during fabrication to attain an increased shear rate on its microstructure. The effect of the process on the surface roughness has been quantified by optical profilometry and the results showed that the root-mean-square surface roughness has been reduced from 0.40 nm to 0.15 nm. The improvement in the fiber core surface quality entailed fibers with ultralow loss in the short-wavelength range. We report on fibers with record loss values as low as 50 dB/km at 290 nm, 9.7 dB/km at 369 nm, 5.0 dB/km at 480 nm, and 1.8 dB/km at 719 nm. The results reveal this new approach as a promising path for the development of hollow-core fibers guiding at short wavelengths with loss that can potentially be orders of magnitude lower than the ones achievable with their silica-core counterparts.
△ Less
Submitted 22 July, 2022;
originally announced July 2022.
-
Map** out the glassy landscape of a mesoscopic elastoplastic model
Authors:
Dheeraj Kumar,
Sylvain Patinet,
Craig E. Maloney,
Ido Regev,
Damien Vandembroucq,
Muhittin Mungan
Abstract:
We develop a mesoscopic model to study the plastic behavior of an amorphous material under cyclic loading. The model is depinning-like and driven by a disordered thresholds dynamics which are coupled by long-range elastic interactions. We propose a simple protocol of "glass preparation" which allows us to mimic thermalisation at high temperature, as well as aging at vanishing temperature. Various…
▽ More
We develop a mesoscopic model to study the plastic behavior of an amorphous material under cyclic loading. The model is depinning-like and driven by a disordered thresholds dynamics which are coupled by long-range elastic interactions. We propose a simple protocol of "glass preparation" which allows us to mimic thermalisation at high temperature, as well as aging at vanishing temperature. Various levels of glass stabilities (from brittle to ductile) can be achieved by tuning the aging duration. The aged glasses are then immersed into a quenched disorder landscape and serve as initial configurations for various protocols of mechanical loading by shearing. The dependence of the plastic behavior upon monotonous loading is recovered. The behavior under cyclic loading is studied for different ages and system sizes. The size and age dependence of the irreversibility transition is discussed. A thorough characterization of the disorder-landscape is achieved through the analysis of the transition graphs, which describe the plastic deformation pathways under athermal quasi-static shear. In particular, the analysis of the stability ranges of the strongly connected components of the transition graphs reveals the emergence of a phase-separation like process associated with the aging of the glass. Increasing the age and hence stability of the initial glass, results in a gradual break-up of the landscape of dynamically accessible stable states into three distinct regions: one region centered around the initially prepared glass phase, and two additional regions, characterized by well-separated ranges of positive and negative plastic strains, each of which is accessible only from the initial glass phase by passing through the stress peak in the forward, respectively, backward shearing directions.
△ Less
Submitted 6 June, 2022;
originally announced June 2022.
-
Mechanical excitation and marginal triggering during avalanches in sheared amorphous solids
Authors:
David Richard,
Ahmed Elgailani,
Damien Vandembroucq,
M. Lisa Manning,
Craig E Maloney
Abstract:
We study plastic strain during individual avalanches in overdamped particle-scale molecular dynamics (MD) and meso-scale elasto-plastic models (EPM) for amorphous solids sheared in the athermal quasi-static limit. We show that the spatial correlations in plastic activity exhibit a short lengthscale that grows as $t^{3/4}$ in MD and ballistically in EPM, and is generated by mechanical excitation of…
▽ More
We study plastic strain during individual avalanches in overdamped particle-scale molecular dynamics (MD) and meso-scale elasto-plastic models (EPM) for amorphous solids sheared in the athermal quasi-static limit. We show that the spatial correlations in plastic activity exhibit a short lengthscale that grows as $t^{3/4}$ in MD and ballistically in EPM, and is generated by mechanical excitation of nearby sites not necessarily close to their stability thresholds, and a longer lengthscale that grows diffusively for both models and is associated with remote marginally stable sites. These similarities in spatial correlations explain why simple EPMs accurately capture the size distribution of avalanches observed in MD, though the temporal profiles and dynamical critical exponents are quite different.
△ Less
Submitted 11 February, 2022;
originally announced February 2022.
-
Relevance of Shear Transformations in the Relaxation of Supercooled Liquids
Authors:
Matthias Lerbinger,
Armand Barbot,
Damien Vandembroucq,
Sylvain Patinet
Abstract:
While deeply supercooled liquids exhibit divergent viscosity and increasingly heterogeneous dynamics as the temperature drops, their structure shows only seemingly marginal changes. Understanding the nature of relaxation processes in this dramatic slowdown is key for understanding the glass transition. Here, we show by atomistic simulations that the heterogeneous dynamics of glass-forming liquids…
▽ More
While deeply supercooled liquids exhibit divergent viscosity and increasingly heterogeneous dynamics as the temperature drops, their structure shows only seemingly marginal changes. Understanding the nature of relaxation processes in this dramatic slowdown is key for understanding the glass transition. Here, we show by atomistic simulations that the heterogeneous dynamics of glass-forming liquids strongly correlate with the local residual plastic strengths along soft directions computed in the initial inherent structures. The correlation increases with decreasing temperature and is maximum in the vicinity of the relaxation time. For the lowest temperature investigated, this maximum is comparable with the best values from the literature dealing with the structure-property relationship. However, the nonlinear probe of the local shear resistance in soft directions provides here a real-space picture of relaxation processes. Our detection method of thermal rearrangements allows us to investigate the first passage time statistics and to study the scaling between the activation energy barriers and the residual plastic strengths. These results shed new light on the nature of relaxations of glassy systems by emphasizing the analogy between the thermal relaxations in viscous liquids and the plastic shear transformation in amorphous solids.
△ Less
Submitted 2 November, 2022; v1 submitted 26 September, 2021;
originally announced September 2021.
-
Predicting plasticity in disordered solids from structural indicators
Authors:
D. Richard,
M. Ozawa,
S. Patinet,
E. Stanifer,
B. Shang,
S. A. Ridout,
B. Xu,
G. Zhang,
P. K. Morse,
J. -L. Barrat,
L. Berthier,
M. L. Falk,
P. Guan,
A. J. Liu,
K. Martens,
S. Sastry,
D. Vandembroucq,
E. Lerner,
M. L. Manning
Abstract:
Amorphous solids lack long-range order. Therefore identifying structural defects -- akin to dislocations in crystalline solids -- that carry plastic flow in these systems remains a daunting challenge. By comparing many different structural indicators in computational models of glasses, under a variety of conditions we carefully assess which of these indicators are able to robustly identify the str…
▽ More
Amorphous solids lack long-range order. Therefore identifying structural defects -- akin to dislocations in crystalline solids -- that carry plastic flow in these systems remains a daunting challenge. By comparing many different structural indicators in computational models of glasses, under a variety of conditions we carefully assess which of these indicators are able to robustly identify the structural defects responsible for plastic flow in amorphous solids. We further demonstrate that the density of defects changes as a function of material preparation and strain in a manner that is highly correlated with the macroscopic material response. Our work represents an important step towards predicting how and when an amorphous solid will fail from its microscopic structure.
△ Less
Submitted 23 November, 2020; v1 submitted 25 March, 2020;
originally announced March 2020.
-
Origin of the Bauschinger Effect in Amorphous Solids
Authors:
Sylvain Patinet,
Armand Barbot,
Matthias Lerbinger,
Damien Vandembroucq,
Anaël Lemaître
Abstract:
We study the structural origin of the Bauschinger effect by accessing numerically the local plastic thresholds in the steady state flow of a two-dimensional model glass under athermal quasistatic deformation. More specifically, we compute the local residual strength, $Δτ^{c}$, for arbitrary loading orientations and find that plastic deformation generically induces material polarization, i.e., a fo…
▽ More
We study the structural origin of the Bauschinger effect by accessing numerically the local plastic thresholds in the steady state flow of a two-dimensional model glass under athermal quasistatic deformation. More specifically, we compute the local residual strength, $Δτ^{c}$, for arbitrary loading orientations and find that plastic deformation generically induces material polarization, i.e., a forward-backward asymmetry in the $Δτ^{c}$ distribution. In steady plastic flow, local packings are on average closer to forward (rather than backward) instabilities, due to the stress-induced bias of barriers. However, presumably due to mechanical noise, a significant fraction of zones lie close to reverse (backward) yielding, as the distribution of $Δτ^{c}$ for reverse shearing extends quasilinearly down to zero local residual strength. By constructing an elementary model of the early plastic response, we then show that unloading causes reverse plasticity of a growing amplitude, i.e., reverse softening, while it shifts away forward-yielding barriers. This result in an inversion of polarization in the low-$Δτ^{c}$ region and, consequently, in the Bauschinger effect. This scenario is quite generic, which explains the pervasiveness of the effect.
△ Less
Submitted 9 May, 2020; v1 submitted 24 June, 2019;
originally announced June 2019.
-
Rejuvenation and Shear-Banding in model amorphous solids
Authors:
Armand Barbot,
Matthias Lerbinger,
Anaël Lemaître,
Damien Vandembroucq,
Sylvain Patinet
Abstract:
We measure the local yield stress, at the scale of small atomic regions, in a deeply quenched two-dimensional glass model undergoing shear banding in response to athermal quasistatic (AQS) deformation. We find that the occurrence of essentially a single plastic event suffices to bring the local yield stress distribution to a well-defined value for all strain orientations, thus essentially erasing…
▽ More
We measure the local yield stress, at the scale of small atomic regions, in a deeply quenched two-dimensional glass model undergoing shear banding in response to athermal quasistatic (AQS) deformation. We find that the occurrence of essentially a single plastic event suffices to bring the local yield stress distribution to a well-defined value for all strain orientations, thus essentially erasing the memory of the initial structure. It follows that in a well-relaxed sample, plastic events cause the abrupt (nucleation-like) emergence of a local softness contrast and thus precipitate the formation of a band, which, in its early stages, is measurably softer than the steady-state flow. Moreover, this postevent yield stress ensemble presents a mean value comparable to that of the inherent states of a supercooled liquid around the mode-coupling temperature $T_{\rm MCT}$. This, we argue, explains that the transition between brittle and ductile yielding in amorphous materials occurs around a comparable parent temperature. Our data also permit to capture quantitatively the contributions of pressure and density changes and demonstrate unambiguously that they are negligible compared with the changes of softness caused by structural rejuvenation.
△ Less
Submitted 16 March, 2020; v1 submitted 23 June, 2019;
originally announced June 2019.
-
Avalanches, thresholds, and diffusion in meso-scale amorphous plasticity
Authors:
Botond Tyukodi,
Damien Vandembroucq,
Craig E Maloney
Abstract:
We present results on a meso-scale model for amorphous matter in athermal, quasi-static (a-AQS), steady state shear flow. In particular, we perform a careful analysis of the scaling with the lateral system size, $L$, of: i) statistics of individual relaxation events in terms of stress relaxation, $S$, and individual event mean-squared displacement, $M$, and the subsequent load increments, $Δγ$, re…
▽ More
We present results on a meso-scale model for amorphous matter in athermal, quasi-static (a-AQS), steady state shear flow. In particular, we perform a careful analysis of the scaling with the lateral system size, $L$, of: i) statistics of individual relaxation events in terms of stress relaxation, $S$, and individual event mean-squared displacement, $M$, and the subsequent load increments, $Δγ$, required to initiate the next event; ii) static properties of the system encoded by $x=σ_y-σ$, the distance of local stress values from threshold; and iii) long-time correlations and the emergence of diffusive behavior. For the event statistics, we find that the distribution of $S$ is similar to, but distinct from, the distribution of $M$. We find a strong correlation between $S$ and $M$ for any particular event, with $S\sim M^{q}$ with $q\approx 0.65$. $q$ completely determines the scaling exponents for $P(M)$ given those for $P(S)$. For the distribution of local thresholds, we find $P(x)$ is analytic at $x=0$, and has a value $\left. P(x)\right|_{x=0}=p_0$ which scales with lateral system length as $p_0\sim L^{-0.6}$. Extreme value statistics arguments lead to a scaling relation between the exponents governing $P(x)$ and those governing $P(S)$. Finally, we study the long-time correlations via single-particle tracer statistics. The value of the diffusion coefficient is completely determined by $\langle Δγ\rangle$ and the scaling properties of $P(M)$ (in particular from $\langle M \rangle$) rather than directly from $P(S)$ as one might have naively guessed. Our results: i) further define the a-AQS universality class, ii) clarify the relation between avalanches of stress relaxation and diffusive behavior, iii) clarify the relation between local threshold distributions and event statistics.
△ Less
Submitted 17 May, 2019;
originally announced May 2019.
-
Chain level insights into tensile-compressive asymmetry in glassy and semicrystalline polymers
Authors:
Sara Jabbari-Farouji,
Damien Vandembroucq
Abstract:
Using molecular dynamics simulations, we provide chain-level insights into the dissimilarities in rearrangements of polymers under uniaxial tensile and compressive deformation in glassy and semicrystalline samples of varying chain lengths. The organization of polymers under tension and compression is distinctively different. The chains align themselves along the tensile axis leading to a net globa…
▽ More
Using molecular dynamics simulations, we provide chain-level insights into the dissimilarities in rearrangements of polymers under uniaxial tensile and compressive deformation in glassy and semicrystalline samples of varying chain lengths. The organization of polymers under tension and compression is distinctively different. The chains align themselves along the tensile axis leading to a net global nematic ordering of their bonds and end-to-end vectors whereas under compression, the polymers arrange themselves in a plane perpendicular to the compressive axis resulting in emergence of an anti-nematic ordering of the bonds and the chain end-to-end vectors. Moreover, the degree of polymers unfolding is greater under tension and they deform less affinely when compared to chains under compression. The difference between the two responses strongly depends on the chain length and is the largest at intermediate chain lengths.
△ Less
Submitted 20 January, 2019;
originally announced January 2019.
-
Diffusion in mesoscopic lattice models of amorphous plasticity
Authors:
Botond Tyukodi,
Craig E Maloney,
Damien Vandembroucq
Abstract:
We present results on tagged particle diffusion in a meso-scale lattice model for sheared amorphous material in athermal quasi-static conditions. We find a short time diffusive regime and a long time diffusive regime whose diffusion coefficients depend on system size in dramatically different ways. At short time, we find that the diffusion coefficient, $D$, scales roughly linearly with system leng…
▽ More
We present results on tagged particle diffusion in a meso-scale lattice model for sheared amorphous material in athermal quasi-static conditions. We find a short time diffusive regime and a long time diffusive regime whose diffusion coefficients depend on system size in dramatically different ways. At short time, we find that the diffusion coefficient, $D$, scales roughly linearly with system length, $D\sim L^{1.05}$. This short time behavior is consistent with particle-based simulations. The long-time diffusion coefficient scales like $D\sim L^{1.6}$, close to previous studies which found $D\sim L^{1.5}$. Furthermore, we show that the near-field details of the interaction kernel do not affect the short time behavior, but qualitatively and dramatically affect the long time behavior, potentially causing a saturation of the mean-squared displacement at long times. Our finding of a $D\sim L^{1.05}$ short time scaling resolves a long standing puzzle about the disagreement between the diffusion coefficient measured in particle-based models and meso-scale lattice models of amorphous plasticity.
△ Less
Submitted 15 March, 2018;
originally announced March 2018.
-
Local yield stress statistics in model amorphous solids
Authors:
Armand Barbot,
Matthias Lerbinger,
Anier Hernandez-Garcia,
Reinaldo Garcia-Garcia,
Michael L. Falk,
Damien Vandembroucq,
Sylvain Patinet
Abstract:
We develop and extend a method presented in [S. Patinet, D. Vandembroucq, and M. L. Falk, Phys. Rev. Lett., 117, 045501 (2016)] to compute the local yield stresses at the atomic scale in model two-dimensional Lennard-Jones glasses produced via differing quench protocols. This technique allows us to sample the plastic rearrangements in a non-perturbative manner for different loading directions on a…
▽ More
We develop and extend a method presented in [S. Patinet, D. Vandembroucq, and M. L. Falk, Phys. Rev. Lett., 117, 045501 (2016)] to compute the local yield stresses at the atomic scale in model two-dimensional Lennard-Jones glasses produced via differing quench protocols. This technique allows us to sample the plastic rearrangements in a non-perturbative manner for different loading directions on a well-controlled length scale. Plastic activity upon shearing correlates strongly with the locations of low yield stresses in the quenched states. This correlation is higher in more structurally relaxed systems. The distribution of local yield stresses is also shown to strongly depend on the quench protocol: the more relaxed the glass, the higher the local plastic thresholds. Analysis of the magnitude of local plastic relaxations reveals that stress drops follow exponential distributions, justifying the hypothesis of an average characteristic amplitude often conjectured in mesoscopic or continuum models. The amplitude of the local plastic rearrangements increases on average with the yield stress, regardless of the system preparation. The local yield stress varies with the shear orientation tested and strongly correlates with the plastic rearrangement locations when the system is sheared correspondingly. It is thus argued that plastic rearrangements are the consequence of shear transformation zones encoded in the glass structure that possess weak slip planes along different orientations. Finally, we justify the length scale employed in this work and extract the yield threshold statistics as a function of the size of the probing zones. This method makes it possible to derive physically grounded models of plasticity for amorphous materials by directly revealing the relevant details of the shear transformation zones that mediate this process.
△ Less
Submitted 15 February, 2018;
originally announced February 2018.
-
Bending transition in the penetration of a flexible intruder in a 2D dense granular medium
Authors:
Nicolas Algarra,
Panagiotis Karagiannopoulos,
Arnaud Lazarus,
Damien Vandembroucq,
Evelyne Kolb
Abstract:
We study the quasi-static penetration of a flexible beam in a two-dimensional dense granular medium lying on an horizontal plate. Rather than a buckling-like behavior we observe a transition between a regime of crack-like penetration in which the fiber only shows small fluctuations around a stable straight geometry and a bending regime in which the fiber fully bends and advances through series of…
▽ More
We study the quasi-static penetration of a flexible beam in a two-dimensional dense granular medium lying on an horizontal plate. Rather than a buckling-like behavior we observe a transition between a regime of crack-like penetration in which the fiber only shows small fluctuations around a stable straight geometry and a bending regime in which the fiber fully bends and advances through series of loading/unloading steps. We show that the shape reconfiguration of the fiber is controlled by a single non dimensional parameter: L/Lc, the ratio of the length of the flexible beam L to Lc, a bending elasto-granular length scale that depends on the rigidity of the fiber and on the departure from the jamming packing fraction of the granular medium. We show moreover that the dynamics of the bending transition in the course of the penetration experiment is gradual and is accompanied by a symmetry breaking of the granular packing fraction in the vicinity of the fiber. Together with the progressive bending of the fiber, a cavity grows downstream of the fiber and the accumulation of grains upstream of the fiber leads to the development of a jammed cluster of grains. We discuss our experimental results in the framework of a simple model of bending-induced compaction and we show that the rate of the bending transition only depends on the control parameter L/Lc.
△ Less
Submitted 7 August, 2017;
originally announced August 2017.
-
Anisotropic super-attenuation of capillary waves on driven glass interfaces
Authors:
Bruno Bresson,
Coralie Brun,
Xavier Buet,
Yong Chen,
Matteo Ciccotti,
Jérôme Gâteau,
Greg Jasion,
Marco Petrovich,
Francesco Poletti,
David Richardson,
Seyed Sandoghchi,
Gilles Tessier,
Botond Tyukodi,
Damien Vandembroucq
Abstract:
Metrological AFM measurements are performed on the silica glass interfaces of photonic band-gap fibres and hollow capillaries. The freezing of attenuated out-of-equilibrium capillary waves during the drawing process is shown to result in a reduced surface roughness. The roughness attenuation with respect to the expected thermodynamical limit is determined to vary with the drawing stress following…
▽ More
Metrological AFM measurements are performed on the silica glass interfaces of photonic band-gap fibres and hollow capillaries. The freezing of attenuated out-of-equilibrium capillary waves during the drawing process is shown to result in a reduced surface roughness. The roughness attenuation with respect to the expected thermodynamical limit is determined to vary with the drawing stress following a power law. A striking anisotropic character of the height correlation is observed: glass surfaces thus retain a structural record of the direction of the flow to which the liquid was submitted.
△ Less
Submitted 6 June, 2017;
originally announced June 2017.
-
Topological symmetry breaking in viscous coarsening
Authors:
David Bouttes,
Emmanuelle Gouillart,
Damien Vandembroucq
Abstract:
The crucial role of hydrodynamic pinch-off instabilities is evidenced in the coarsening stage of viscous liquids. The phase separation of a barium borosilicate glass melt is studied by in-situ synchrotron X-Ray tomography at high temperature. The high viscosity contrast between the less viscous phase and the more viscous phase induces a topological symmetry breaking: capillary breakups occur prefe…
▽ More
The crucial role of hydrodynamic pinch-off instabilities is evidenced in the coarsening stage of viscous liquids. The phase separation of a barium borosilicate glass melt is studied by in-situ synchrotron X-Ray tomography at high temperature. The high viscosity contrast between the less viscous phase and the more viscous phase induces a topological symmetry breaking: capillary breakups occur preferentially in the less viscous phase. As a result, contrasting morphologies are obtained in the two phases. This symmetry breaking is illustrated on three different glass compositions , corresponding to different volume fractions of the two phases. In particular, a fragmentation phenomenon, reminiscent of the end-pinching mechanism proposed by Stone et al. [1, 2] is evidenced in the less viscous phase.
△ Less
Submitted 31 May, 2016;
originally announced May 2016.
-
Driven interfaces: from flow to creep through model reduction
Authors:
Elisabeth Agoritsas,
Reinaldo García-García,
Vivien Lecomte,
Lev Truskinovsky,
Damien Vandembroucq
Abstract:
The response of spatially extended systems to a force leading their steady state out of equilibrium is strongly affected by the presence of disorder. We focus on the mean velocity induced by a constant force applied on one-dimensional interfaces. In the absence of disorder, the velocity is linear in the force. In the presence of disorder, it is widely admitted, as well as experimentally and numeri…
▽ More
The response of spatially extended systems to a force leading their steady state out of equilibrium is strongly affected by the presence of disorder. We focus on the mean velocity induced by a constant force applied on one-dimensional interfaces. In the absence of disorder, the velocity is linear in the force. In the presence of disorder, it is widely admitted, as well as experimentally and numerically verified, that the velocity presents a stretched exponential dependence in the force (the so-called 'creep law'), which is out of reach of linear response, or more generically of direct perturbative expansions at small force. In dimension one, there is no exact analytical derivation of such a law, even from a theoretical physical point of view. We propose an effective model with two degrees of freedom, constructed from the full spatially extended model, that captures many aspects of the creep phenomenology. It provides a justification of the creep law form of the velocity-force characteristics, in a quasistatic approximation. It allows, moreover, to capture the non-trivial effects of short-range correlations in the disorder, which govern the low-temperature asymptotics. It enables us to establish a phase diagram where the creep law manifests itself in the vicinity of the origin in the force--system-size--temperature coordinates. Conjointly, we characterise the crossover between the creep regime and a linear-response regime that arises due to finite system size.
△ Less
Submitted 28 July, 2016; v1 submitted 14 May, 2016;
originally announced May 2016.
-
Cracks in random brittle solids: From fiber bundles to continuum mechanics
Authors:
Sylvain Patinet,
Damien Vandembroucq,
Alex Hansen,
Stéphane Roux
Abstract:
Statistical models are essential to get a better understanding of the role of disorder in brittle disordered solids. Fiber bundle models play a special role as a paradigm, with a very good balance of simplicity and non-trivial effects. We introduce here a variant of the fiber bundle model where the load is transferred among the fibers through a very compliant membrane. This Soft Membrane fiber bun…
▽ More
Statistical models are essential to get a better understanding of the role of disorder in brittle disordered solids. Fiber bundle models play a special role as a paradigm, with a very good balance of simplicity and non-trivial effects. We introduce here a variant of the fiber bundle model where the load is transferred among the fibers through a very compliant membrane. This Soft Membrane fiber bundle mode reduces to the classical Local Load Sharing fiber bundle model in 1D. Highlighting the continuum limit of the model allows to compute an equivalent toughness for the fiber bundle and hence discuss nucleation of a critical defect. The computation of the toughness allows for drawing a simple connection with crack front propagation (depinning) models.
△ Less
Submitted 9 November, 2015;
originally announced November 2015.
-
Finite size effects on crack front pinning at heterogeneous planar interfaces: Experimental, finite elements and perturbation approaches
Authors:
Sylvain Patinet,
L Alzate,
E Barthel,
D Dalmas,
D Vandembroucq,
V Lazarus
Abstract:
Understanding the role played by the microstructure of materials on their macroscopic failure properties is an important challenge in solid mechanics. Indeed, when a crack propagates at a heterogeneous brittle interface, the front is trapped by tougher regions and deforms. This pinning induces non-linearities in the crack propagation problem, even within Linear Elastic Fracture Mechanics theory, a…
▽ More
Understanding the role played by the microstructure of materials on their macroscopic failure properties is an important challenge in solid mechanics. Indeed, when a crack propagates at a heterogeneous brittle interface, the front is trapped by tougher regions and deforms. This pinning induces non-linearities in the crack propagation problem, even within Linear Elastic Fracture Mechanics theory, and modifies the overall failure properties of the material. For example crack front pinning by tougher places could increase the fracture resistance of multilayer structures, with interesting technological applications. Analytical perturbation approaches, based on Bueckner-Rice elastic line models, focus on the crack front perturbations, hence allow for a description of these phenomena. Here, they are applied to experiments investigating the propagation of a purely interfacial crack in a simple toughness pattern: a single defect strip surrounded by homogeneous interface. We show that by taking into account the finite size of the body, quantitative agreement with experimental and finite elements results is achieved. In particular this method allows to predict the toughness contrast, i.e. the toughness difference between the single defect strip and its homogeneous surrounding medium. This opens the way to a more accurate use of the perturbation method to study more disordered heterogeneous materials, where the finite elements method is less adequate. From our results, we also propose a simple method to determine the adhesion energy of tough interfaces by measuring the crack front deformation induced by known interface patterns.
△ Less
Submitted 6 November, 2015;
originally announced November 2015.
-
Finite size effects in a model for plasticity of amorphous composites
Authors:
Botond Tyukodi,
Claire A. Lemarchand,
Jesper S. Hansen,
Damien Vandembroucq
Abstract:
We discuss the plastic behavior of an amorphous matrix reinforced by hard particles. A mesoscopic depinning-like model accounting for Eshelby elastic interactions is implemented. Only the effect of a plastic disorder is considered. Numerical results show a complex size-dependence of the effective flow stress of the amorphous composite. In particular the departure from the mixing law shows opposite…
▽ More
We discuss the plastic behavior of an amorphous matrix reinforced by hard particles. A mesoscopic depinning-like model accounting for Eshelby elastic interactions is implemented. Only the effect of a plastic disorder is considered. Numerical results show a complex size-dependence of the effective flow stress of the amorphous composite. In particular the departure from the mixing law shows opposite trends associated to the competing effects of the matrix and the reinforcing particles respectively. The reinforcing mechanisms and their effects on localization are discussed. Plastic strain is shown to gradually concentrate on the weakest band of the system. This correlation of the plastic behavior with the material structure is used to design a simple analytical model. The latter nicely captures reinforcement size effects in $-(\log N/N)^{1/2}$ observed numerically. Predictions of the effective flow stress accounting for further logarithmic corrections show a very good agreement with numerical results.
△ Less
Submitted 22 September, 2015;
originally announced September 2015.
-
From depinning transition to plastic yielding of amorphous media: A soft modes perspective
Authors:
Botond Tyukodi,
Sylvain Patinet,
Stéphane Roux,
Damien Vandembroucq
Abstract:
A mesoscopic model of amorphous plasticity is discussed in the context of depinning models. After embedding in a d + 1 dimensional space, where the accumulated plastic strain lives along the additional dimension, the gradual plastic deformation of amorphous media can be regarded as the motion of an elastic manifold in a disordered landscape. While the associated depinning transition leads to scali…
▽ More
A mesoscopic model of amorphous plasticity is discussed in the context of depinning models. After embedding in a d + 1 dimensional space, where the accumulated plastic strain lives along the additional dimension, the gradual plastic deformation of amorphous media can be regarded as the motion of an elastic manifold in a disordered landscape. While the associated depinning transition leads to scaling properties, the quadrupolar Eshelby interactions at play in amorphous plasticity induce specific additional features like shear-banding and weak ergodicity breakdown. The latters are shown to be controlled by the existence of soft modes of the elastic interaction, the consequence of which is discussed in the context of depinning.
△ Less
Submitted 14 June, 2016; v1 submitted 26 February, 2015;
originally announced February 2015.
-
Hydrodynamic coarsening in phase-separated silicate melts
Authors:
David Bouttes,
Océane Lambert,
Corinne Claireaux,
William Woelffel,
Davy Dalmas,
Emmanuelle Gouillart,
Pierre Lhuissier,
Luc Salvo,
Elodie Boller,
Damien Vandembroucq
Abstract:
Using in-situ synchrotron tomography, we investigate the coarsening dynamics of barium borosilicate melts during phase separation. The 3-D geometry of the two interconnected phases is determined thanks to image processing. We observe a linear growth of the size of domains with time, at odds with the sublinear diffusive growth usually observed in phase-separating glasses or alloys. Such linear coar…
▽ More
Using in-situ synchrotron tomography, we investigate the coarsening dynamics of barium borosilicate melts during phase separation. The 3-D geometry of the two interconnected phases is determined thanks to image processing. We observe a linear growth of the size of domains with time, at odds with the sublinear diffusive growth usually observed in phase-separating glasses or alloys. Such linear coarsening is attributed to viscous flow inside the bicontinuous phases, and quantitative measurements show that the growth rate is well explained by the ratio of surface tension over viscosity. The geometry of the domains is shown to be statistically similar at different times, provided that the microstructure is rescaled by the average domain size. Complementary experiments on melts with a droplet morphology demonstrate that viscous flow prevails over diffusion in the large range of domain sizes measured in our experiments (1 - 80 microns).
△ Less
Submitted 12 February, 2015;
originally announced February 2015.
-
Fragmentation and Limits to Dynamical Scaling in Viscous Coarsening: An Interrupted in situ X-Ray Tomographic Study
Authors:
David Bouttes,
Emmanuelle Gouillart,
Elodie Boller,
Davy Dalmas,
Damien Vandembroucq
Abstract:
X-Ray microtomography was used to follow the coarsening of the structure of a ternary silicate glass experiencing phase separation in the liquid state. The volumes, surfaces, mean and Gaussian curvatures of the domains of minority phase were measured after reconstruction of the 3D images and segmentation. A linear growth law of the characteristic length scale $\ell \sim t$ was observed. A detailed…
▽ More
X-Ray microtomography was used to follow the coarsening of the structure of a ternary silicate glass experiencing phase separation in the liquid state. The volumes, surfaces, mean and Gaussian curvatures of the domains of minority phase were measured after reconstruction of the 3D images and segmentation. A linear growth law of the characteristic length scale $\ell \sim t$ was observed. A detailed morphological study was performed. While dynamical scaling holds for most of the geometrical observables under study, a progressive departure from scaling invariance of the distributions of local curvatures was evidenced. The latter results from a gradual fragmentation of the structure in the less viscous phase that also leads to a power-law size distribution of isolated domains.
△ Less
Submitted 4 September, 2014; v1 submitted 6 September, 2013;
originally announced September 2013.
-
Quantitative prediction of effective toughness at random heterogeneous interfaces
Authors:
Sylvain Patinet,
Damien Vandembroucq,
Stéphane Roux
Abstract:
The propagation of an adhesive crack through an anisotropic heterogeneous interface is considered. Tuning the local toughness distribution function and spatial correlation is numerically shown to induce a transition between weak to strong pinning conditions. While the macroscopic effective toughness is given by the mean local toughness in case of weak pinning, a systematic toughness enhancement is…
▽ More
The propagation of an adhesive crack through an anisotropic heterogeneous interface is considered. Tuning the local toughness distribution function and spatial correlation is numerically shown to induce a transition between weak to strong pinning conditions. While the macroscopic effective toughness is given by the mean local toughness in case of weak pinning, a systematic toughness enhancement is observed for strong pinning (the critical point of the depinning transition). A self-consistent approximation is shown to account very accurately for this evolution, without any free parameter.
△ Less
Submitted 15 February, 2014; v1 submitted 16 December, 2012;
originally announced December 2012.
-
Micro-Brillouin spectroscopy map** of the residual density field induced by Vickers indentation in a soda-lime silicate glass
Authors:
H. Tran,
S. Clément,
R. Vialla,
D. Vandembroucq,
B. Rufflé
Abstract:
High-resolution Brillouin scattering is used to achieve 3-dimensional maps of the longitudinal acoustic mode frequency shift in soda-lime silicate glasses subject to Vickers indentations. Assuming that residual stress-induced effects are simply proportional to density changes, residual densification fields are obtained. The density gradient is nearly isotropic, confirming earlier optical observati…
▽ More
High-resolution Brillouin scattering is used to achieve 3-dimensional maps of the longitudinal acoustic mode frequency shift in soda-lime silicate glasses subject to Vickers indentations. Assuming that residual stress-induced effects are simply proportional to density changes, residual densification fields are obtained. The density gradient is nearly isotropic, confirming earlier optical observations made on a similar glass. The results show that Brillouin micro-spectroscopy opens the way to a fully quantitative comparison of experimental data with predictions of mechanical models for the identification of a constitutive law.
△ Less
Submitted 21 May, 2012; v1 submitted 14 March, 2012;
originally announced March 2012.
-
Modeling the mechanics of amorphous solids at different length and time scales
Authors:
David Rodney,
Anne Tanguy,
Damien Vandembroucq
Abstract:
We review the recent literature on the simulation of the structure and deformation of amorphous glasses, including oxide and metallic glasses. We consider simulations at different length and time scales. At the nanometer scale, we review studies based on atomistic simulations, with a particular emphasis on the role of the potential energy landscape and of the temperature. At the micrometer scale,…
▽ More
We review the recent literature on the simulation of the structure and deformation of amorphous glasses, including oxide and metallic glasses. We consider simulations at different length and time scales. At the nanometer scale, we review studies based on atomistic simulations, with a particular emphasis on the role of the potential energy landscape and of the temperature. At the micrometer scale, we present the different mesoscopic models of amorphous plasticity and show the relation between shear banding and the type of disorder and correlations (e.g. elastic) included in the models. At the macroscopic range, we review the different constitutive laws used in finite element simulations. We end the review by a critical discussion on the opportunities and challenges offered by multiscale modeling and transfer of information between scales to study amorphous plasticity.
△ Less
Submitted 11 July, 2011;
originally announced July 2011.
-
Mechanical noise dependent Aging and Shear Banding behavior of a mesoscopic model of amorphous plasticity
Authors:
Damien Vandembroucq,
Stéphane Roux
Abstract:
We discuss aging and localization in a simple "Eshelby" mesoscopic model of amorphous plasticity. Plastic deformation is assumed to occur through a series of local reorganizations. Using a discretization of the mechanical fields on a discrete lattice, local reorganizations are modeled as local slip events. Local yield stresses are randomly distributed in space and invariant in time. Each plastic s…
▽ More
We discuss aging and localization in a simple "Eshelby" mesoscopic model of amorphous plasticity. Plastic deformation is assumed to occur through a series of local reorganizations. Using a discretization of the mechanical fields on a discrete lattice, local reorganizations are modeled as local slip events. Local yield stresses are randomly distributed in space and invariant in time. Each plastic slip event induces a long-ranged elastic stress redistribution. Mimicking the effect of aging, we focus on the behavior of the model when the initial state is characterized by a distribution of high local yield stress values. A dramatic effect on the localization behavior is obtained: the system first spontaneously self-traps to form a shear band which then only slowly widens. The higher the "age" parameter the more localized the plastic strain field. Two-time correlation computed on the stress field show a divergent correlation time with the age parameter. The amplitude of a local slip event (the prefactor of the Eshelby singularity) as compared to the yield stress distribution width acts here as an effective temperature-like parameter: the lower the slip increment, the higher the localization and the decorrelation time.
△ Less
Submitted 5 December, 2011; v1 submitted 26 April, 2011;
originally announced April 2011.
-
Avalanches, precursors and finite size fluctuations in a mesoscopic model of amorphous plasticity
Authors:
Mehdi Talamali,
Viljo Petäjä,
Damien Vandembroucq,
Stéphane Roux
Abstract:
We discuss avalanche and finite size fluctuations in a mesoscopic model to describe the shear plasticity of amorphous materials. Plastic deformation is assumed to occur through series of local reorganizations. Yield stress criteria are random while each plastic slip event induces a quadrupolar long range elastic stress redistribution. The model is discretized on a regular square lattice. Shear pla…
▽ More
We discuss avalanche and finite size fluctuations in a mesoscopic model to describe the shear plasticity of amorphous materials. Plastic deformation is assumed to occur through series of local reorganizations. Yield stress criteria are random while each plastic slip event induces a quadrupolar long range elastic stress redistribution. The model is discretized on a regular square lattice. Shear plasticity can be studied in this context as a depinning dynamic phase transition. We show evidence for a scale free distribution of avalanches $P(s)\propto S^{-κ}$ with a non trivial exponent $κ\approx 1.25$ significantly different from the mean field result $κ= 1.5$. Finite size effects allow for a characterization of the scaling invariance of the yield stress fluctuations observed in small samples. We finally identify a population of precursors of plastic activity and characterize its spatial distribution.
△ Less
Submitted 5 December, 2011; v1 submitted 25 March, 2011;
originally announced March 2011.
-
Strain localization and anisotropic correlations in a mesoscopic model of amorphous plasticity
Authors:
Mehdi Talamali,
Viljo Petäjä,
Damien Vandembroucq,
Stéphane Roux
Abstract:
A mesoscopic model for shear plasticity of amorphous materials in two dimensions is introduced, and studied through numerical simulations in order to elucidate the macroscopic (large scale) mechanical behavior. Plastic deformation is assumed to occur through a series of local reorganizations. Using a discretization of the mechanical fields on a discrete lattice, local reorganizations are modeled a…
▽ More
A mesoscopic model for shear plasticity of amorphous materials in two dimensions is introduced, and studied through numerical simulations in order to elucidate the macroscopic (large scale) mechanical behavior. Plastic deformation is assumed to occur through a series of local reorganizations. Using a discretization of the mechanical fields on a discrete lattice, local reorganizations are modeled as local slip events. Local yield stresses are randomly distributed in space and invariant in time. Each plastic slip event induces a long-ranged elastic stress redistribution. Rate and thermal effects are not discussed in the present study. Extremal dynamics allows for recovering many of the complex features of amorphous plasticity observed experimentally and in numerical atomistic simulations in the quasi-static regime. In particular, a quantitative picture of localization, and of the anisotropic strain correlation both in the initial transient regime, and in the steady state are provided. In addition, the preparation of the amorphous sample is shown to have a crucial effect of on the localization behavior.
△ Less
Submitted 13 February, 2012; v1 submitted 14 May, 2010;
originally announced May 2010.
-
Plasticity-induced structural anisotropy of silica glass
Authors:
Cindy Linn Rountree,
Damien Vandembroucq,
Mehdi Talamali,
Elisabeth Bouchaud,
Stéphane Roux
Abstract:
Amorphous silica density at ambient pressure is known to depend on thermal history (through the quenching rate) but also, at room temperature, on the maximum pressure applied in the past. Here we show that beyond density, a mechanical loading can endow the structure with an orientational order. Molecular dynamics simulations show evidence that amorphous silica develops a permanent anisotropic st…
▽ More
Amorphous silica density at ambient pressure is known to depend on thermal history (through the quenching rate) but also, at room temperature, on the maximum pressure applied in the past. Here we show that beyond density, a mechanical loading can endow the structure with an orientational order. Molecular dynamics simulations show evidence that amorphous silica develops a permanent anisotropic structure after extended shear plastic flow. This anisotropy which survives for an unstressed specimen is revealed markedly by the fabric tensor computed over the Si-O-Si orientations, albeit the SiO4 tetrahedra microstructure remains mostly unaltered.
△ Less
Submitted 14 May, 2009;
originally announced May 2009.
-
Density hardening plasticity and mechanical aging of silica glass under pressure: A Raman spectroscopic study
Authors:
Damien Vandembroucq,
Thierry Deschamps,
Camille Coussa,
Antoine Perriot,
Etienne Barthel,
Bernard Champagnon,
Christine Martinet
Abstract:
In addition of a flow, plastic deformation of structural glasses (in particular amorphous silica) is characterized by a permanent densification. Raman spectroscopic estimators are shown to give a full account of the plastic behavior of silica under pressure. While the permanent densification of silica has been widely discussed in terms of amorphous-amorphous transition, from a plasticity point o…
▽ More
In addition of a flow, plastic deformation of structural glasses (in particular amorphous silica) is characterized by a permanent densification. Raman spectroscopic estimators are shown to give a full account of the plastic behavior of silica under pressure. While the permanent densification of silica has been widely discussed in terms of amorphous-amorphous transition, from a plasticity point of view, the evolution of the residual densification with the maximum pressure of a pressure cycle can be discussed as a density hardening phenomenon. In the framework of such a mechanical aging effect, we propose that the glass structure could be labelled by the maximum pressure experienced by the glass and that the saturation of densification could be associated with the densest packing of tetrahedra only linked by their vertices.
△ Less
Submitted 13 May, 2009; v1 submitted 22 February, 2008;
originally announced February 2008.
-
Path independent integrals to identify localized plastic events in two dimensions
Authors:
Mehdi Talamali,
Viljo Petäjä,
Damien Vandembroucq,
Stéphane Roux
Abstract:
We use a power expansion representation of plane elasticity complex potentials due to Kolossov and Muskhelishvili, to compute the elastic fields induced by a localized plastic deformation event. Far from its center, the dominant contributions correspond to first order singularities of quadrupolar and dipolar symmetry which can be associated respectively to pure deviatoric and pure volumetric pla…
▽ More
We use a power expansion representation of plane elasticity complex potentials due to Kolossov and Muskhelishvili, to compute the elastic fields induced by a localized plastic deformation event. Far from its center, the dominant contributions correspond to first order singularities of quadrupolar and dipolar symmetry which can be associated respectively to pure deviatoric and pure volumetric plastic strain of an equivalent circular inclusion. Constructing holomorphic functions from the displacement field and its derivatives, it is possible to define path independent Cauchy integrals which capture the amplitudes of these singularities. Analytical expressions and numerical tests on simple finite element data are presented. The development of such numerical tools is of direct interest for the identification of local structural reorganizations which are believed to be the key mechanisms for plasticity of amorphous materials.
△ Less
Submitted 13 May, 2009; v1 submitted 28 January, 2008;
originally announced January 2008.
-
Crack propagation through phase separated glasses: effect of the characteristic size of disorder
Authors:
Davy Dalmas,
Anne Lelarge,
Damien Vandembroucq
Abstract:
We perform fracture experiments on nanoscale phase separated glasses and measure crack surface roughness by atomic force microscopy. The ability of tuning the phase domain size by thermal treatment allows us to test thoroughly the predictions of crack font depinning models about the scaling properties of crack surface roughness. It appears that in the range of validity of these depinning models…
▽ More
We perform fracture experiments on nanoscale phase separated glasses and measure crack surface roughness by atomic force microscopy. The ability of tuning the phase domain size by thermal treatment allows us to test thoroughly the predictions of crack font depinning models about the scaling properties of crack surface roughness. It appears that in the range of validity of these depinning models developed for the fracture of brittle materials, our experimental results show a quantitative agreement with theoretical predictions: beyond the characteristic size of disorder, the roughness of crack surfaces obeys the logarithmic scaling early predicted by Ramanathan, Ertas and Fisher (PRL97)
△ Less
Submitted 13 May, 2009; v1 submitted 27 December, 2007;
originally announced December 2007.
-
Quantitative AFM analysis of phase separated borosilicate glass surfaces
Authors:
Davy Dalmas,
Anne Lelarge,
Damien Vandembroucq
Abstract:
Phase separated borosilicate glass samples were prepared by applying various heat treatments. Using selective chemical etching we performed AFM measurement on the phase separated glass surfaces. A quantitative roughness analysis allowed us to measure precisely the dependence of the characteristic size of the phase domains on heating time and temperature. The experimental measurements are very we…
▽ More
Phase separated borosilicate glass samples were prepared by applying various heat treatments. Using selective chemical etching we performed AFM measurement on the phase separated glass surfaces. A quantitative roughness analysis allowed us to measure precisely the dependence of the characteristic size of the phase domains on heating time and temperature. The experimental measurements are very well described by the theoretically expected scaling laws. Interdiffusion coefficients and activation energy are estimated from this analysis and are consistent with literature data.
△ Less
Submitted 31 October, 2006;
originally announced October 2006.
-
Frozen capillary waves on glass surfaces: an AFM study
Authors:
Thomas Sarlat,
Anne Lelarge,
Elin Sondergard,
Damien Vandembroucq
Abstract:
Using atomic force microscopy on silica and float glass surfaces, we give evidence that the roughness of melted glass surfaces can be quantitatively accounted for by frozen capillary waves. In this framework the height spatial correlations are shown to obey a logarithmic scaling law; the identification of this behaviour allows to estimate the ratio $kT\_F/πγ$ where $k$ is the Boltzmann constant,…
▽ More
Using atomic force microscopy on silica and float glass surfaces, we give evidence that the roughness of melted glass surfaces can be quantitatively accounted for by frozen capillary waves. In this framework the height spatial correlations are shown to obey a logarithmic scaling law; the identification of this behaviour allows to estimate the ratio $kT\_F/πγ$ where $k$ is the Boltzmann constant, $γ$ the interface tension and $T\_F$ the temperature corresponding to the ``freezing'' of the capillary waves. Variations of interface tension and (to a lesser extent) temperatures of annealing treatments are shown to be directly measurable from a statistical analysis of the roughness spectrum of the glass surfaces.
△ Less
Submitted 31 October, 2006;
originally announced October 2006.
-
Material-independent crack arrest statistics: Application to indentation experiments
Authors:
Yann Charles,
François Hild,
Stéphane Roux,
Damien Vandembroucq
Abstract:
An extensive experimental study of indentation and crack arrest statistics is presented for four different brittle materials (alumina, silicon carbide, silicon nitride, glass). Evidence is given that the crack length statistics can be described by a universal (i.e. material independent) distribution. The latter directly derives from results obtained when modeling crack propagation as a depinning…
▽ More
An extensive experimental study of indentation and crack arrest statistics is presented for four different brittle materials (alumina, silicon carbide, silicon nitride, glass). Evidence is given that the crack length statistics can be described by a universal (i.e. material independent) distribution. The latter directly derives from results obtained when modeling crack propagation as a depinning phenomenon. Crack arrest (or effective toughness) statistics appears to be fully characterized by two parameters, namely, an asymptotic crack length (or macroscopic toughness) value and a power law size dependent width. The experimental knowledge of the crack arrest statistics at one given scale thus gives access to its knowledge at all scales.
△ Less
Submitted 28 February, 2007; v1 submitted 6 April, 2006;
originally announced April 2006.
-
The mechanics of glass and functionalised glass surfaces
Authors:
E. Barthel,
M. Beauvais,
R. Briard,
N. Chemin,
D. Dalmas,
C. Heitz,
M. Klotz,
P. Nael,
A. Perriot,
A. Pinquier,
S. Roux,
L. Serreau,
E. Sondergard,
D. Vandembroucq
Abstract:
Glass is highly sensitive to surface flaws generated by contact. Surface cracks threaten both its mechanical strength and visual aspect. Recent trends in glass functionalisation by grafting or coating lend an even more prominent role to the surface. For these reasons, the glass surface mechanics, which couples surface physico-chemistry with mechanical response, must be considered in details to o…
▽ More
Glass is highly sensitive to surface flaws generated by contact. Surface cracks threaten both its mechanical strength and visual aspect. Recent trends in glass functionalisation by grafting or coating lend an even more prominent role to the surface. For these reasons, the glass surface mechanics, which couples surface physico-chemistry with mechanical response, must be considered in details to optimize glass processing and products. We review a few recent advances in the field of glass surface mechanics, with special emphasis on the local ductility of silicate glasses and the mechanical stability of films and coatings.
△ Less
Submitted 19 October, 2005;
originally announced October 2005.
-
Laplacian transfer across a rough interface: Numerical resolution in the conformal plane
Authors:
Damien Vandembroucq,
Stéphane Roux
Abstract:
We use a conformal map** technique to study the Laplacian transfer across a rough interface. Natural Dirichlet or Von Neumann boundary condition are simply read by the conformal map. Mixed boundary condition, albeit being more complex can be efficiently treated in the conformal plane. We show in particular that an expansion of the potential on a basis of evanescent waves in the conformal plane…
▽ More
We use a conformal map** technique to study the Laplacian transfer across a rough interface. Natural Dirichlet or Von Neumann boundary condition are simply read by the conformal map. Mixed boundary condition, albeit being more complex can be efficiently treated in the conformal plane. We show in particular that an expansion of the potential on a basis of evanescent waves in the conformal plane allows to write a well-conditioned 1D linear system. These general principle are illustrated by numerical results on rough interfaces.
△ Less
Submitted 7 April, 2005;
originally announced April 2005.
-
Raman microspectroscopic characterization of amorphous silica plastic behavior
Authors:
Antoine Perriot,
Valérie Martinez,
Laurent Grosvalet,
Christine Martinet,
Bernard Champagnon,
Damien Vandembroucq,
Etienne Barthel
Abstract:
Raman microspectroscopy was used to characterize amorphous silica plastic behavior. Using a correlation between Raman spectrum and density, a map of the local residual indentation-induced densification is obtained. The existence of a densification-induced hardening is also evidenced through a diamond anvil cell experiment. Such observations are not accounted for by the previously proposed harden…
▽ More
Raman microspectroscopy was used to characterize amorphous silica plastic behavior. Using a correlation between Raman spectrum and density, a map of the local residual indentation-induced densification is obtained. The existence of a densification-induced hardening is also evidenced through a diamond anvil cell experiment. Such observations are not accounted for by the previously proposed hardening-free pressure-dependent yield criterion based on indentation curves. These results open the way to more accurate description of a constitutive law for amorphous silica.
△ Less
Submitted 3 February, 2006; v1 submitted 28 September, 2004;
originally announced September 2004.
-
Light scattering from cold rolled aluminum surfaces
Authors:
Damien Vandembroucq,
Annie Tarrats,
Jean-Jacques Greffet,
Stephane Roux,
Franck Plouraboue
Abstract:
We present experimental light scattering measurements from aluminum surfaces obtained by cold rolling. We show that our results are consistent with a scale invariant description of the roughness of these surfaces. The roughness parameters that we obtain from the light scattering experiment are consistent with those obtained from Atomic Force Microscopy measurements.
We present experimental light scattering measurements from aluminum surfaces obtained by cold rolling. We show that our results are consistent with a scale invariant description of the roughness of these surfaces. The roughness parameters that we obtain from the light scattering experiment are consistent with those obtained from Atomic Force Microscopy measurements.
△ Less
Submitted 14 September, 2004;
originally announced September 2004.
-
Material independent crack arrest statistics
Authors:
Yann Charles,
Damien Vandembroucq,
Francois Hild,
Stephane Roux
Abstract:
The propagation of (planar) cracks in a heterogeneous brittle material characterized by a random field of toughness is considered, taking into account explicitly the effect of the crack front roughness on the local stress intensity factor. In the so-called strong-pinning regime, the onset of crack propagation appears to map onto a second-order phase transition characterized by universal critical…
▽ More
The propagation of (planar) cracks in a heterogeneous brittle material characterized by a random field of toughness is considered, taking into account explicitly the effect of the crack front roughness on the local stress intensity factor. In the so-called strong-pinning regime, the onset of crack propagation appears to map onto a second-order phase transition characterized by universal critical exponents which are independent of the local characteristics of the medium. Propagation over large distances can be described by using a simple one-dimensional description, with a correlation length and an effective macroscopic toughness distribution that scale in a non-trivial fashion with the crack front length. As an application of the above concepts, the arrest of indentation cracks is addressed, and the analytical expression for the statistical distribution of the crack radius at arrest is derived. The analysis of indentation crack radii on alumina is shown to obey the predicted algebraic expression for the radius distribution and its dependence on the indentation load.
△ Less
Submitted 2 September, 2004;
originally announced September 2004.
-
Effective toughness of heterogeneous brittle materials
Authors:
Stephane Roux,
Damien Vandembroucq,
Francois Hild
Abstract:
A heterogeneous brittle material characterized by a random field of local toughness Kc(x) can be represented by an equivalent homogeneous medium of toughness, Keff. Homogenization refers to a process of estimating Keff from the local field Kc(x). An approach based on a perturbative expansion of the stress intensity factor along a rough crack front shows the occurrence of different regimes depend…
▽ More
A heterogeneous brittle material characterized by a random field of local toughness Kc(x) can be represented by an equivalent homogeneous medium of toughness, Keff. Homogenization refers to a process of estimating Keff from the local field Kc(x). An approach based on a perturbative expansion of the stress intensity factor along a rough crack front shows the occurrence of different regimes depending on the correlation length of the local toughness field in the direction of crack propagation. A `"weak pinning" regime takes place for long correlation lengths, where the effective toughness is the average of the local toughness. For shorter correlation lengths, a transition to "strong pinning" occurs leading to a much higher effective toughness, and characterized by a propagation regime consisting in jumps between pinning configurations.
△ Less
Submitted 2 September, 2004;
originally announced September 2004.
-
Electromagnetic wave scattering from conducting self-affine surfaces : An analytic and numerical study
Authors:
Ingve Simonsen,
Damien Vandembroucq,
Stephane Roux
Abstract:
We derive an analytical expression for the scattering of a scalar wave from a perfectly conducting self-affine one dimensional surface in the framework of the Kirchhoff approximation. We show that most of the results can be recovered via a scaling analysis. We identify the typical slope taken over one wavelength as the relevant parameter controlling the scattering process. We compare our predict…
▽ More
We derive an analytical expression for the scattering of a scalar wave from a perfectly conducting self-affine one dimensional surface in the framework of the Kirchhoff approximation. We show that most of the results can be recovered via a scaling analysis. We identify the typical slope taken over one wavelength as the relevant parameter controlling the scattering process. We compare our predictions with direct numerical simulations performed on surfaces of varying roughness parameters and confirm the broad range of applicability of our description up to very large roughness. Finally we check that a non zero electrical resistivity provided small does not invalidate our results.
△ Less
Submitted 2 September, 2004; v1 submitted 18 August, 2004;
originally announced August 2004.
-
Conformal Map** on Rough Boundaries II: Applications to bi-harmonic problems
Authors:
Damien Vandembroucq,
Stephane Roux
Abstract:
We use a conformal map** method introduced in a companion paper to study the properties of bi-harmonic fields in the vicinity of rough boundaries. We focus our analysis on two different situations where such bi-harmonic problems are encountered: a Stokes flow near a rough wall and the stress distribution on the rough interface of a material in uni-axial tension. We perform a complete numerical…
▽ More
We use a conformal map** method introduced in a companion paper to study the properties of bi-harmonic fields in the vicinity of rough boundaries. We focus our analysis on two different situations where such bi-harmonic problems are encountered: a Stokes flow near a rough wall and the stress distribution on the rough interface of a material in uni-axial tension. We perform a complete numerical solution of these two-dimensional problems for any univalued rough surfaces. We present results for sinusoidal and self-affine surface whose slope can locally reach 2.5. Beyond the numerical solution we present perturbative solutions of these problems. We show in particular that at first order in roughness amplitude, the surface stress of a material in uni-axial tension can be directly obtained from the Hilbert transform of the local slope. In case of self-affine surfaces, we show that the stress distribution presents, for large stresses, a power law tail whose exponent continuously depends on the roughness amplitude.
△ Less
Submitted 11 August, 2004;
originally announced August 2004.
-
Conformal Map** on Rough Boundaries I: Applications to harmonic problems
Authors:
Damien Vandembroucq,
Stephane Roux
Abstract:
The aim of this study is to analyze the properties of harmonic fields in the vicinity of rough boundaries where either a constant potential or a zero flux is imposed, while a constant field is prescribed at an infinite distance from this boundary. We introduce a conformal map** technique that is tailored to this problem in two dimensions. An efficient algorithm is introduced to compute the con…
▽ More
The aim of this study is to analyze the properties of harmonic fields in the vicinity of rough boundaries where either a constant potential or a zero flux is imposed, while a constant field is prescribed at an infinite distance from this boundary. We introduce a conformal map** technique that is tailored to this problem in two dimensions. An efficient algorithm is introduced to compute the conformal map for arbitrarily chosen boundaries. Harmonic fields can then simply be read from the conformal map. We discuss applications to "equivalent" smooth interfaces. We study the correlations between the topography and the field at the surface. Finally we apply the conformal map to the computation of inhomogeneous harmonic fields such as the derivation of Green function for localized flux on the surface of a rough boundary.
△ Less
Submitted 9 August, 2004;
originally announced August 2004.
-
Large scale numerical simulations of "ultrametric" long-range depinning
Authors:
Damien Vandembroucq,
Stephane Roux
Abstract:
The depinning of an elastic line interacting with a quenched disorder is studied for long range interactions, applicable to crack propagation or wetting. An ultrametric distance is introduced instead of the Euclidean distance, allowing for a drastic reduction of the numerical complexity of the problem. Based on large scale simulations, two to three orders of magnitude larger than previously cons…
▽ More
The depinning of an elastic line interacting with a quenched disorder is studied for long range interactions, applicable to crack propagation or wetting. An ultrametric distance is introduced instead of the Euclidean distance, allowing for a drastic reduction of the numerical complexity of the problem. Based on large scale simulations, two to three orders of magnitude larger than previously considered, we obtain a very precise determination of critical exponents which are shown to be indistinguishable from their Euclidean metric counterparts. Moreover the scaling functions are shown to be unchanged. The choice of an ultrametric distance thus does not affect the universality class of the depinning transition and opens the way to an analytic real space renormalization group approach.
△ Less
Submitted 26 January, 2004;
originally announced January 2004.
-
Universal depinning force fluctuations of an elastic line: Application to finite temperature behavior
Authors:
Damien Vandembroucq,
Rune Skoe,
Stephane Roux
Abstract:
The depinning of an elastic line in a random medium is studied via an extremal model. The latter gives access to the instantaneous depinning force for each successive conformation of the line. Based on conditional statistics the universal and non-universal parts of the depinning force distribution can be obtained. In particular the singular behavior close to a (macroscopic) critical threshold is…
▽ More
The depinning of an elastic line in a random medium is studied via an extremal model. The latter gives access to the instantaneous depinning force for each successive conformation of the line. Based on conditional statistics the universal and non-universal parts of the depinning force distribution can be obtained. In particular the singular behavior close to a (macroscopic) critical threshold is obtained as a function of the roughness exponent of the front. We show moreover that the advance of the front is controlled by a very tenuous set of subcritical sites. Extension of the extremal model to a finite temperature is proposed, the scaling properties of which can be discussed based on the statistics of depinning force at zero temperature.
△ Less
Submitted 20 November, 2003;
originally announced November 2003.
-
An extremal model for amorphous media plasticity
Authors:
Jean-Christophe Baret,
Damien Vandembroucq,
Stephane Roux
Abstract:
An extremal model for the plasticity of amorphous materials is studied in a simple two-dimensional anti-plane geometry. The steady-state is analyzed through numerical simulations. Long-range spatial and temporal correlations in local slip events are shown to develop, leading to non-trivial and highly anisotropic scaling laws. In particular, the plastic strain is shown to statistically concentrat…
▽ More
An extremal model for the plasticity of amorphous materials is studied in a simple two-dimensional anti-plane geometry. The steady-state is analyzed through numerical simulations. Long-range spatial and temporal correlations in local slip events are shown to develop, leading to non-trivial and highly anisotropic scaling laws. In particular, the plastic strain is shown to statistically concentrate over a region which tends to align perpendicular to the displacement gradient. By construction, the model can be seen as giving rise to a depinning transition, the threshold of which (i.e. the macroscopic yield stress) also reveal scaling properties reflecting the localization of the activity.
△ Less
Submitted 26 June, 2002;
originally announced June 2002.
-
Front propagation in random media: From extremal to activated dynamics
Authors:
Rune Skoe,
Damien Vandembroucq,
Stephane Roux
Abstract:
Front propagation in a random environment is studied close to the depinning threshold. At zero temperature we show that the depinning force distribution exhibits a universal behavior. This property is used to estimate the velocity of the front at very low temperature. We obtain a Arrhenius behavior with a prefactor depending on the temperature as a power law. These results are supported by numer…
▽ More
Front propagation in a random environment is studied close to the depinning threshold. At zero temperature we show that the depinning force distribution exhibits a universal behavior. This property is used to estimate the velocity of the front at very low temperature. We obtain a Arrhenius behavior with a prefactor depending on the temperature as a power law. These results are supported by numerical simulations.
△ Less
Submitted 7 March, 2002;
originally announced March 2002.
-
Wave scattering from self-affine surfaces
Authors:
Ingve Simonsen,
Damien Vandembroucq,
Stephane Roux
Abstract:
Electromagnetic wave scattering from a perfectly reflecting self-affine surface is considered. Within the framework of the Kirchhoff approximation, we show that the scattering cross section can be exactly written as a function of the scattering angle via a centered symmetric Levy distribution for general roughness amplitude, Hurst exponent and wavelength of the incident wave. The amplitude of th…
▽ More
Electromagnetic wave scattering from a perfectly reflecting self-affine surface is considered. Within the framework of the Kirchhoff approximation, we show that the scattering cross section can be exactly written as a function of the scattering angle via a centered symmetric Levy distribution for general roughness amplitude, Hurst exponent and wavelength of the incident wave. The amplitude of the specular peak, its width and its position are discussed as well as the power law decrease (with scattering angle) of the scattering cross section.
△ Less
Submitted 9 July, 1999;
originally announced July 1999.