-
Geometry dependence of TLS noise and loss in a-SiC:H parallel plate capacitors for superconducting microwave resonators
Authors:
K. Kouwenhoven,
G. P. J. van Doorn,
B. T. Buijtendorp,
S. A. H. de Rooij,
D. Lamers,
D. J. Thoen,
V. Murugesan,
J. J. A. Baselmans,
P. J. de Visser
Abstract:
Parallel plate capacitors (PPC) significantly reduce the size of superconducting microwave resonators, reducing the pixel pitch for arrays of single photon energy-resolving kinetic inductance detectors (KIDs). The frequency noise of KIDs is typically limited by tunneling Two-Level Systems (TLS), which originate from lattice defects in the dielectric materials required for PPCs. How the frequency n…
▽ More
Parallel plate capacitors (PPC) significantly reduce the size of superconducting microwave resonators, reducing the pixel pitch for arrays of single photon energy-resolving kinetic inductance detectors (KIDs). The frequency noise of KIDs is typically limited by tunneling Two-Level Systems (TLS), which originate from lattice defects in the dielectric materials required for PPCs. How the frequency noise level depends on the PPC's dimensions has not been experimentally addressed. We measure the frequency noise of 56 resonators with a-SiC:H PPCs, which cover a factor 44 in PPC area and a factor 4 in dielectric thickness. To support the noise analysis, we measure the TLS-induced, power-dependent, intrinsic loss and temperature-dependent resonance frequency shift of the resonators. From the TLS models, we expect a geometry-independent microwave loss and resonance frequency shift, set by the TLS properties of the dielectric. However, we observe a thickness-dependent microwave loss and resonance frequency shift, explained by surface layers that limit the performance of PPC-based resonators. For a uniform dielectric, the frequency noise level should scale directly inversely with the PPC area and thickness. We observe that an increase in PPC size reduces the frequency noise, but the exact scaling is, in some cases, weaker than expected. Finally, we derive an engineering guideline for the design of KIDs based on PPC-based resonators.
△ Less
Submitted 8 May, 2024; v1 submitted 21 November, 2023;
originally announced November 2023.
-
Modeling and Testing Superconducting Artificial CPW Lines Suitable for Parametric Amplification
Authors:
F. P. Mena,
D. Valenzuela,
C. Espinoza,
F. Pizarro,
B. -K. Tan,
D. J. Thoen,
J. J. A. Baselmans,
R. Finger
Abstract:
Achieving amplification with high gain and quantum-limited noise is a difficult problem to solve. Parametric amplification using a superconducting transmission line with high kinetic inductance is a promising technology not only to solve this problem but also adding several benefits. When compared with other technologies, they have the potential of improving power saturation, achieving larger frac…
▽ More
Achieving amplification with high gain and quantum-limited noise is a difficult problem to solve. Parametric amplification using a superconducting transmission line with high kinetic inductance is a promising technology not only to solve this problem but also adding several benefits. When compared with other technologies, they have the potential of improving power saturation, achieving larger fractional bandwidths and operating at higher frequencies. In this type of amplifiers, selecting the proper transmission line is a key element in their design. Given current fabrication limitations, traditional lines such as coplanar waveguides (CPW), are not ideal for this purpose since it is difficult to make them with the proper characteristic impedance for good matching and slow-enough phase velocity for making them more compact. Capacitively-loaded lines, also known as artificial lines, are a good solution to this problem. However, few design rules or models have been presented to guide their accurate design. This fact is even more crucial considering that they are usually fabricated in the form of Floquet lines that have to be designed carefully to suppress undesired harmonics appearing in the parametric process. In this article we present, firstly, a new modelling strategy, based on the use of electromagnetic-simulation software, and, secondly, a first-principles model that facilitate and speed the design of CPW artificial lines and of Floquet lines made out of them. Then, we present comparisons with experimental results that demonstrate their accuracy. Finally, the theoretical model allows to predict the high-frequency behaviour of the artificial lines showing that they are good candidates for implementing parametric amplifiers above 100 GHz.
△ Less
Submitted 23 October, 2023;
originally announced October 2023.
-
Pointing calibration of GroundBIRD telescope using Moon observation data
Authors:
Y. Sueno,
J. J. A. Baselmans,
A. H. M. Coppens,
R. T Génova-Santos,
M. Hattori,
S. Honda,
K. Karatsu,
H. Kutsuma,
K. Lee,
T. Nagasaki,
S. Oguri,
C. Otani,
M. Peel,
J. Suzuki,
O. Tajima,
T. Tanaka,
M. Tsujii,
D. J. Thoen,
E. Won
Abstract:
Understanding telescope pointing (i.e., line of sight) is important for observing the cosmic microwave background (CMB) and astronomical objects. The Moon is a candidate astronomical source for pointing calibration. Although the visible size of the Moon ($\ang{;30}$) is larger than that of the planets, we can frequently observe the Moon once a month with a high signal-to-noise ratio. We developed…
▽ More
Understanding telescope pointing (i.e., line of sight) is important for observing the cosmic microwave background (CMB) and astronomical objects. The Moon is a candidate astronomical source for pointing calibration. Although the visible size of the Moon ($\ang{;30}$) is larger than that of the planets, we can frequently observe the Moon once a month with a high signal-to-noise ratio. We developed a method for performing pointing calibration using observational data from the Moon. We considered the tilts of the telescope axes as well as the encoder and collimation offsets for pointing calibration. In addition, we evaluated the effects of the nonuniformity of the brightness temperature of the Moon, which is a dominant systematic error. As a result, we successfully achieved a pointing accuracy of $\ang{;3.3}$. This is one order of magnitude smaller than an angular resolution of $\ang{;36}$. This level of accuracy competes with past achievements in other ground-based CMB experiments using observational data from the planets.
△ Less
Submitted 17 January, 2024; v1 submitted 30 August, 2023;
originally announced August 2023.
-
Ultra-sensitive Super-THz Microwave Kinetic Inductance Detectors for future space telescopes
Authors:
J. J. A. Baselmans,
F. Facchin,
A. Pascual Laguna,
J. Bueno,
D. J. Thoen,
V. Murugesan,
N. Llombart,
P. de Visser
Abstract:
Future actively cooled space-borne observatories for the far-infrared, loosely defined as a 1--10 THz band, can potentially reach a sensitivity limited only by background radiation from the Universe. This will result in an increase in observing speed of many orders of magnitude. A spectroscopic instrument on such an observatory requires large arrays of detectors with a sensitivity expressed as a n…
▽ More
Future actively cooled space-borne observatories for the far-infrared, loosely defined as a 1--10 THz band, can potentially reach a sensitivity limited only by background radiation from the Universe. This will result in an increase in observing speed of many orders of magnitude. A spectroscopic instrument on such an observatory requires large arrays of detectors with a sensitivity expressed as a noise equivalent power NEP = 3 $\times 10^{-20}$ $W\surd{Hz}$. We present the design, fabrication, and characterisation of microwave kinetic inductance detectors (MKIDs) for this frequency range reaching the required sensitivity. The devices are based on thin-film NbTiN resonators which use lens-antenna coupling to a submicron-width aluminium transmission line at the shorted end of the resonator where the radiation is absorbed. We optimised the MKID geometry for a low NEP by using a small aluminium volume of $\approx$ 1$μm^3$ and fabricating the aluminium section on a very thin (100 nm) SiN membrane. Both methods of optimisation also reduce the effect of excess noise by increasing the responsivity of the device, which is further increased by reducing the parasitic geometrical inductance of the resonator. We measure the sensitivity of eight MKIDs with respect to the power absorbed in the detector using a thermal calibration source filtered in a narrow band around 1.55 THz. We obtain a NEP$_{exp}(P_{abs})\:=\:3.1\pm0.9\times10^{-20}\:W\surd{Hz}$ at a modulation frequency of 200 Hz averaged over all measured MKIDs. The NEP is limited by quasiparticle trap**. The measured sensitivity is sufficient for spectroscopic observations from future, actively cooled space-based observatories. Moreover, the presented device design and assembly can be adapted for frequencies up to $\approx$ 10 THz and can be readily implemented in kilopixel arrays.
△ Less
Submitted 18 July, 2022;
originally announced July 2022.
-
Resolving Power of Visible to Near-Infrared Hybrid $β$-Ta/NbTiN Kinetic Inductance Detectors
Authors:
Kevin Kouwenhoven,
Daniel Fan,
Enrico Biancalani,
Steven A. H. de Rooij,
Tawab Karim,
Carlas S. Smith,
Vignesh Murugesan,
David J. Thoen,
Jochem J. A. Baselmans,
Pieter J. de Visser
Abstract:
Kinetic Inductance Detectors (KIDs) are superconducting energy-resolving detectors, sensitive to single photons from the near-infrared to ultraviolet. We study a hybrid KID design consisting of a beta phase tantalum ($β$-Ta) inductor and a NbTiN interdigitated capacitor (IDC). The devices show an average intrinsic quality factor $Q_i$ of 4.3$\times10^5$ $\pm$ 1.3 $\times10^5$. To increase the powe…
▽ More
Kinetic Inductance Detectors (KIDs) are superconducting energy-resolving detectors, sensitive to single photons from the near-infrared to ultraviolet. We study a hybrid KID design consisting of a beta phase tantalum ($β$-Ta) inductor and a NbTiN interdigitated capacitor (IDC). The devices show an average intrinsic quality factor $Q_i$ of 4.3$\times10^5$ $\pm$ 1.3 $\times10^5$. To increase the power captured by the light sensitive inductor, we 3D-print an array of 150$\times$150 $μ$m resin micro lenses on the backside of the sapphire substrate. The shape deviation between design and printed lenses is smaller than 1$μ$m, and the alignment accuracy of this process is $δ_x = +5.8 \pm 0.5$ $μ$m and $δ_y = +8.3 \pm 3.3$ $μ$m. We measure a resolving power for 1545-402 nm that is limited to 4.9 by saturation in the KID's phase response. We can model the saturation in the phase response with the evolution of the number of quasiparticles generated by a photon event. An alternative coordinate system that has a linear response raises the resolving power to 5.9 at 402 nm. We verify the measured resolving power with a two-line measurement using a laser source and a monochromator. We discuss several improvements that can be made to the devices on a route towards KID arrays with high resolving powers.
△ Less
Submitted 13 February, 2023; v1 submitted 12 July, 2022;
originally announced July 2022.
-
DESHIMA 2.0: development of an integrated superconducting spectrometer for science-grade astronomical observations
Authors:
Akio Taniguchi,
Tom J. L. C. Bakx,
Jochem J. A. Baselmans,
Robert Huiting,
Kenichi Karatsu,
Nuria Llombart,
Matus Rybak,
Tatsuya Takekoshi,
Yoichi Tamura,
Hiroki Akamatsu,
Stefanie Brackenhoff,
Juan Bueno,
Bruno T. Buijtendorp,
Shahab Dabironezare,
Anne-Kee Doing,
Yasunori Fujii,
Kazuyuki Fujita,
Matthijs Gouwerok,
Sebastian Hähnle,
Tsuyoshi Ishida,
Shun Ishii,
Ryohei Kawabe,
Tetsu Kitayama,
Kotaro Kohno,
Akira Kouchi
, et al. (10 additional authors not shown)
Abstract:
Integrated superconducting spectrometer (ISS) technology will enable ultra-wideband, integral-field spectroscopy for (sub)millimeter-wave astronomy, in particular, for uncovering the dust-obscured cosmic star formation and galaxy evolution over cosmic time. Here we present the development of DESHIMA 2.0, an ISS for ultra-wideband spectroscopy toward high-redshift galaxies. DESHIMA 2.0 is designed…
▽ More
Integrated superconducting spectrometer (ISS) technology will enable ultra-wideband, integral-field spectroscopy for (sub)millimeter-wave astronomy, in particular, for uncovering the dust-obscured cosmic star formation and galaxy evolution over cosmic time. Here we present the development of DESHIMA 2.0, an ISS for ultra-wideband spectroscopy toward high-redshift galaxies. DESHIMA 2.0 is designed to observe the 220-440 GHz band in a single shot, corresponding to a redshift range of $z$=3.3-7.6 for the ionized carbon emission ([C II] 158 $μ$m). The first-light experiment of DESHIMA 1.0, using the 332-377 GHz band, has shown an excellent agreement among the on-sky measurements, the lab measurements, and the design. As a successor to DESHIMA 1.0, we plan the commissioning and the scientific observation campaign of DESHIMA 2.0 on the ASTE 10-m telescope in 2023. Ongoing upgrades for the full octave-bandwidth system include the wideband 347-channel chip design and the wideband quasi-optical system. For efficient measurements, we also develop the observation strategy using the mechanical fast sky-position chopper and the sky-noise removal technique based on a novel data-scientific approach. In the paper, we show the recent status of the upgrades and the plans for the scientific observation campaign.
△ Less
Submitted 4 October, 2022; v1 submitted 27 October, 2021;
originally announced October 2021.
-
Model and Measurements of an Optical Stack for Broadband Visible to Near-IR Absorption in TiN KIDs
Authors:
K. Kouwenhoven,
I. Elwakil,
J. van Wingerden,
V. Murugesan,
D. J. Thoen,
J. J. A. Baselmans,
P. J. de Visser
Abstract:
Typical materials for optical Kinetic Inductance Detetectors (KIDs) are metals with a natural absorption of 30-50% in the visible and near-infrared. To reach high absorption efficiencies (90-100%) the KID must be embedded in an optical stack. We show an optical stack design for a 60 nm TiN film. The optical stack is modeled as sections of transmission lines, where the parameters for each section a…
▽ More
Typical materials for optical Kinetic Inductance Detetectors (KIDs) are metals with a natural absorption of 30-50% in the visible and near-infrared. To reach high absorption efficiencies (90-100%) the KID must be embedded in an optical stack. We show an optical stack design for a 60 nm TiN film. The optical stack is modeled as sections of transmission lines, where the parameters for each section are related to the optical properties of each layer. We derive the complex permittivity of the TiN film from a spectral ellipsometry measurement. The designed optical stack is optimised for broadband absorption and consists of, from top (illumination side) to bottom: 85 nm SiOx, 60 nm TiN, 23 nm of SiOx, and a 100 nm thick Al mirror. We show the modeled absorption and reflection of this stack, which has >80% absorption from 400 nm to 1550 nm and near-unity absorption for 500 nm to 800 nm. We measure transmission and reflection of this stack with a commercial spectrophotometer. The results are in good agreement with the model.
△ Less
Submitted 15 August, 2022; v1 submitted 12 October, 2021;
originally announced October 2021.
-
Hydrogenated Amorphous Silicon Carbide: A Low-loss Deposited Dielectric for Microwave to Submillimeter Wave Superconducting Circuits
Authors:
B. T. Buijtendorp,
S. Vollebregt,
K. Karatsu,
D. J. Thoen,
V. Murugesan,
K. Kouwenhoven,
S. Hähnle,
J. J. A. Baselmans,
A. Endo
Abstract:
Low-loss deposited dielectrics will benefit superconducting devices such as integrated superconducting spectrometers, superconducting qubits and kinetic inductance parametric amplifiers. Compared with planar structures, multi-layer structures such as microstrips are more compact and eliminate radiation loss at high frequencies. Multi-layer structures are most easily fabricated with deposited diele…
▽ More
Low-loss deposited dielectrics will benefit superconducting devices such as integrated superconducting spectrometers, superconducting qubits and kinetic inductance parametric amplifiers. Compared with planar structures, multi-layer structures such as microstrips are more compact and eliminate radiation loss at high frequencies. Multi-layer structures are most easily fabricated with deposited dielectrics, which typically exhibit higher dielectric loss than crystalline dielectrics. We measured the sub-kelvin and low-power microwave and mm-submm wave dielectric loss of hydrogenated amorphous silicon carbide (a-SiC:H), using a superconducting chip with NbTiN/a-SiC:H/NbTiN microstrip resonators. We deposited the a-SiC:H by plasma-enhanced chemical vapor deposition at a substrate temperature of 400°C. The a-SiC:H has a mm-submm loss tangent ranging from $0.80 \pm 0.01 \times 10^{-4}$ to $1.43 \pm 0.04 \times 10^{-4}$ in the range of 270 to 385 GHz. The microwave loss tangent is $3.2 \pm 0.2 \times 10^{-5}$. These are the lowest low-power sub-kelvin loss tangents that have been reported for microstrip resonators at mm-submm and microwave frequencies. We observe that the loss tangent increases with frequency. The a-SiC:H films are free of blisters and have low stress: $-$20 MPa compressive at 200 nm thickness to 60 MPa tensile at 1000 nm thickness.
△ Less
Submitted 7 October, 2021;
originally announced October 2021.
-
Terahertz Band-Pass Filters for Wideband Superconducting On-chip Filter-bank Spectrometers
Authors:
Alejandro Pascual Laguna,
Kenichi Karatsu,
David J. Thoen,
Vignesh Murugesan,
Bruno T. Buijtendorp,
Akira Endo,
Jochem J. A. Baselmans
Abstract:
A superconducting microstrip half-wavelength resonator is proposed as a suitable band-pass filter for broadband moderate spectral resolution spectroscopy for terahertz (THz) astronomy. The proposed filter geometry has a free spectral range of an octave of bandwidth without introducing spurious resonances, reaches a high coupling efficiency in the pass-band and shows very high rejection in the stop…
▽ More
A superconducting microstrip half-wavelength resonator is proposed as a suitable band-pass filter for broadband moderate spectral resolution spectroscopy for terahertz (THz) astronomy. The proposed filter geometry has a free spectral range of an octave of bandwidth without introducing spurious resonances, reaches a high coupling efficiency in the pass-band and shows very high rejection in the stop-band to minimize reflections and cross-talk with other filters. A spectrally sparse prototype filter-bank in the band 300-400 GHz has been developed employing these filters as well as an equivalent circuit model to anticipate systematic errors. The fabricated chip has been characterized in terms of frequency response, reporting an average peak coupling efficiency of 27% with an average spectral resolution of 940.
△ Less
Submitted 22 September, 2021;
originally announced September 2021.
-
Superconducting Microstrip Losses at Microwave and Sub-millimeter wavelengths
Authors:
S. Hähnle,
K. Kouwenhoven,
B. Buijtendorp,
A. Endo,
K. Karatsu,
D. J. Thoen,
V. Murugesan,
J. J. A. Baselmans
Abstract:
We present a lab-on-chip experiment to accurately measure losses of superconducting microstrip lines at microwave and sub-mm wavelengths. The microstrips are fabricated from NbTiN, which is deposited using reactive magnetron sputtering, and amorphous silicon which is deposited using plasma-enhanced chemical vapor deposition (PECVD). Sub-mm wave losses are measured using on-chip Fabry-P{é}rot reson…
▽ More
We present a lab-on-chip experiment to accurately measure losses of superconducting microstrip lines at microwave and sub-mm wavelengths. The microstrips are fabricated from NbTiN, which is deposited using reactive magnetron sputtering, and amorphous silicon which is deposited using plasma-enhanced chemical vapor deposition (PECVD). Sub-mm wave losses are measured using on-chip Fabry-P{é}rot resonators (FPR) operating around $350\ $GHz. Microwave losses are measured using shunted half-wave resonators with an identical geometry and fabricated on the same chip. We measure a loss tangent of the amorphous silicon at single-photon energies of $\tanδ=3.7\pm0.5\times10^{-5}$ at $6\ $GHz and $\tanδ= 2.1\pm 0.1\times10^{-4}$ at $350\ $GHz. These results represent very low losses for deposited dielectrics, but the sub-mm wave losses are significantly higher than the microwave losses, which cannot be understood using the standard two-level system loss model.
△ Less
Submitted 25 August, 2021;
originally announced August 2021.
-
Phonon-trap** enhanced energy resolution in superconducting single photon detectors
Authors:
Pieter J. de Visser,
Steven A. H. de Rooij,
Vignesh Murugesan,
David J. Thoen,
Jochem J. A. Baselmans
Abstract:
A noiseless, photon counting detector, which resolves the energy of each photon, could radically change astronomy, biophysics and quantum optics. Superconducting detectors promise an intrinsic resolving power at visible wavelengths of $R=E/δE\approx100$ due to their low excitation energy. We study superconducting energy-resolving Microwave Kinetic Inductance Detectors (MKIDs), which hold particula…
▽ More
A noiseless, photon counting detector, which resolves the energy of each photon, could radically change astronomy, biophysics and quantum optics. Superconducting detectors promise an intrinsic resolving power at visible wavelengths of $R=E/δE\approx100$ due to their low excitation energy. We study superconducting energy-resolving Microwave Kinetic Inductance Detectors (MKIDs), which hold particular promise for larger cameras. A visible/near-infrared photon absorbed in the superconductor creates a few thousand quasiparticles through several stages of electron-phonon interaction. Here we demonstrate experimentally that the resolving power of MKIDs at visible to near-infrared wavelengths is limited by the loss of hot phonons during this process. We measure the resolving power of our aluminum-based detector as a function of photon energy using four lasers with wavelengths between $1545-402$ nm. For detectors on thick SiN/Si and sapphire substrates the resolving power is limited to $10-21$ for the respective wavelengths, consistent with the loss of hot phonons. When we suspend the sensitive part of the detector on a 110 nm thick SiN membrane, the measured resolving power improves to $19-52$ respectively. The improvement is equivalent to a factor $8\pm2$ stronger phonon trap** on the membrane, which is consistent with a geometrical phonon propagation model for these hot phonons. We discuss a route towards the Fano limit by phonon engineering.
△ Less
Submitted 11 March, 2021;
originally announced March 2021.
-
Strong Reduction of Quasiparticle Fluctuations in a Superconductor due to Decoupling of the Quasiparticle Number and Lifetime
Authors:
Steven A. H. de Rooij,
Jochem J. A. Baselmans,
Vignesh Murugesan,
David J. Thoen,
Pieter J. de Visser
Abstract:
We measure temperature dependent quasiparticle fluctuations in a small Al volume, embedded in a NbTiN superconducting microwave resonator. The resonator design allows for read-out close to equilibrium. By placing the Al film on a membrane, we enhance the fluctuation level and separate quasiparticle from phonon effects. When lowering the temperature, the recombination time saturates and the fluctua…
▽ More
We measure temperature dependent quasiparticle fluctuations in a small Al volume, embedded in a NbTiN superconducting microwave resonator. The resonator design allows for read-out close to equilibrium. By placing the Al film on a membrane, we enhance the fluctuation level and separate quasiparticle from phonon effects. When lowering the temperature, the recombination time saturates and the fluctuation level reduces a factor $\sim$100. From this we deduce that the number of free quasiparticles is still thermal. Therefore, the theoretical, inverse relation between quasiparticle number and recombination time is invalid in this experiment. This is consistent with quasiparticle trap**, where on-trap recombination limits the observed quasiparticle lifetime.
△ Less
Submitted 24 November, 2021; v1 submitted 8 March, 2021;
originally announced March 2021.
-
Direct evidence for Cooper pairing without a spectral gap in a disordered superconductor above $T_{C}$
Authors:
Koen M. Bastiaans,
Damianos Chatzopoulos,
Jian-Feng Ge,
Doohee Cho,
Willem O. Tromp,
Jan M. van Ruitenbeek,
Mark H. Fischer,
Pieter J. de Visser,
David J. Thoen,
Eduard F. C. Driessen,
Teunis M. Klapwijk,
Milan P. Allan
Abstract:
The idea that preformed Cooper pairs could exist in a superconductor above its zero-resistance state has been explored for unconventional, interface, and disordered superconductors, yet direct experimental evidence is lacking. Here, we use scanning tunneling noise spectroscopy to unambiguously show that preformed Cooper pairs exist up to temperatures much higher than the zero-resistance critical t…
▽ More
The idea that preformed Cooper pairs could exist in a superconductor above its zero-resistance state has been explored for unconventional, interface, and disordered superconductors, yet direct experimental evidence is lacking. Here, we use scanning tunneling noise spectroscopy to unambiguously show that preformed Cooper pairs exist up to temperatures much higher than the zero-resistance critical temperature $T_{C}$ in the disordered superconductor titanium nitride, by observing a clear enhancement in the shot noise that is equivalent to a change of the effective charge from 1 to 2 electron charges. We further show that spectroscopic gap fills up rather than closes when increasing temperature. Our results thus demonstrate the existence of a novel state above $T_{C}$ that, much like an ordinary metal, has no (pseudo)gap, but carries charge via paired electrons.
△ Less
Submitted 21 January, 2021;
originally announced January 2021.
-
Characterization of low-loss hydrogenated amorphous silicon films for superconducting resonators
Authors:
Bruno T. Buijtendorp,
Juan Bueno,
David J. Thoen,
Vignesh Murugesan,
Paolo M. Sberna,
Jochem J. A. Baselmans,
Sten Vollebregt,
Akira Endo
Abstract:
Superconducting resonators used in millimeter-submillimeter astronomy would greatly benefit from deposited dielectrics with a small dielectric loss. We deposited hydrogenated amorphous silicon films using plasma-enhanced chemical vapor deposition, at substrate temperatures of 100°C, 250°C and 350°C. The measured void volume fraction, hydrogen content, microstructure parameter, and bond-angle disor…
▽ More
Superconducting resonators used in millimeter-submillimeter astronomy would greatly benefit from deposited dielectrics with a small dielectric loss. We deposited hydrogenated amorphous silicon films using plasma-enhanced chemical vapor deposition, at substrate temperatures of 100°C, 250°C and 350°C. The measured void volume fraction, hydrogen content, microstructure parameter, and bond-angle disorder are negatively correlated with the substrate temperature. All three films have a loss tangent below $10^{-5}$ for a resonator energy of $10^5$ photons, at 120 mK and 4-7 GHz. This makes these films promising for microwave kinetic inductance detectors and on-chip millimeter-submilimeter filters.
△ Less
Submitted 14 December, 2020;
originally announced December 2020.
-
Simulating the radiation loss of superconducting submillimeter wave filters and transmission lines using Sonnet EM
Authors:
Akira Endo,
Alejandro Pascual Laguna,
Sebastian Hähnle,
Kenichi Karatsu,
David J. Thoen,
Vignesh Murugesan,
Jochem J. A. Baselmans
Abstract:
Superconducting resonators and transmission lines are fundamental building blocks of integrated circuits for millimeter-submillimeter astronomy. Accurate simulation of radiation loss from the circuit is crucial for the design of these circuits because radiation loss increases with frequency, and can thereby deteriorate the system performance. Here we show a stratification for a 2.5-dimensional met…
▽ More
Superconducting resonators and transmission lines are fundamental building blocks of integrated circuits for millimeter-submillimeter astronomy. Accurate simulation of radiation loss from the circuit is crucial for the design of these circuits because radiation loss increases with frequency, and can thereby deteriorate the system performance. Here we show a stratification for a 2.5-dimensional method-of-moment simulator Sonnet EM that enables accurate simulations of the radiative resonant behavior of submillimeter-wave coplanar resonators and straight coplanar waveguides (CPWs). The Sonnet simulation agrees well with the measurement of the transmission through a coplanar resonant filter at 374.6 GHz. Our Sonnet stratification utilizes artificial lossy layers below the lossless substrate to absorb the radiation, and we use co-calibrated internal ports for de-embedding. With this type of stratification, Sonnet can be used to model superconducting millimeter-submillimeter wave circuits even when radiation loss is a potential concern.
△ Less
Submitted 13 December, 2020;
originally announced December 2020.
-
Suppression of radiation loss in high kinetic inductance superconducting co-planar waveguides
Authors:
S. Hähnle,
N. v. Marrewijk,
A. Endo,
K. Karatsu,
D. J. Thoen,
V. Murugesan,
J. J. A. Baselmans
Abstract:
We present a novel lab-on-chip technique to measure the very low losses in superconducting transmission lines at (sub-) mm wavelengths. The chips consist of a 100 nm thick NbTiN Coplanar Waveguide (CPW) Fabry Perot (FP) resonator, coupled on one side to an antenna and on the other side to a Microwave Kinetic Inductance detector. Using a single frequency radiation source allows us to measure the fr…
▽ More
We present a novel lab-on-chip technique to measure the very low losses in superconducting transmission lines at (sub-) mm wavelengths. The chips consist of a 100 nm thick NbTiN Coplanar Waveguide (CPW) Fabry Perot (FP) resonator, coupled on one side to an antenna and on the other side to a Microwave Kinetic Inductance detector. Using a single frequency radiation source allows us to measure the frequency response of the FP around 350 GHz and deduce its losses. We show that the loss is dominated by radiation loss inside the CPW line that forms the FP and that it decreases with decreasing line width and increasing kinetic inductance as expected. The results can be quantitatively understood using SONNET simulations. The lowest loss is observed for a CPW with a total width of $6\ \mathrm{μm}$ and corresponds to a Q-factor of $\approx15,000$.
△ Less
Submitted 28 April, 2020; v1 submitted 23 March, 2020;
originally announced March 2020.
-
DESHIMA on ASTE: On-sky Responsivity Calibration of the Integrated Superconducting Spectrometer
Authors:
Tatsuya Takekoshi,
Kenichi Karatsu,
Junya Suzuki,
Yoichi Tamura,
Tai Oshima,
Akio Taniguchi,
Shin'ichiro Asayama,
Tom J. L. C. Bakx,
Jochem J. A. Baselmans,
Sjoerd Bosma,
Juan Bueno,
Kah Wuy Chin,
Yasunori Fujii,
Kazuyuki Fujita,
Robert Huiting,
Soh Ikarashi,
Tsuyoshi Ishida,
Shun Ishii,
Ryohei Kawabe,
Teun M. Klapwijk,
Kotaro Kohno,
Akira Kouchi,
Nuria Llombart,
Jun Maekawa,
Vignesh Murugesan
, et al. (14 additional authors not shown)
Abstract:
We are develo** an ultra-wideband spectroscopic instrument, DESHIMA (DEep Spectroscopic HIgh-redshift MApper), based on the technologies of an on-chip filter-bank and Microwave Kinetic Inductance Detector (MKID) to investigate dusty star-burst galaxies in the distant universe at millimeter and submillimeter wavelength. An on-site experiment of DESHIMA was performed using the ASTE 10-m telescope.…
▽ More
We are develo** an ultra-wideband spectroscopic instrument, DESHIMA (DEep Spectroscopic HIgh-redshift MApper), based on the technologies of an on-chip filter-bank and Microwave Kinetic Inductance Detector (MKID) to investigate dusty star-burst galaxies in the distant universe at millimeter and submillimeter wavelength. An on-site experiment of DESHIMA was performed using the ASTE 10-m telescope. We established a responsivity model that converts frequency responses of the MKIDs to line-of-sight brightness temperature. We estimated two parameters of the responsivity model using a set of skydip data taken under various precipitable water vapor (PWV, 0.4-3.0 mm) conditions for each MKID. The line-of-sight brightness temperature of sky is estimated using an atmospheric transmission model and the PWVs. As a result, we obtain an average temperature calibration uncertainty of $1σ=4$%, which is smaller than other photometric biases. In addition, the average forward efficiency of 0.88 in our responsivity model is consistent with the value expected from the geometrical support structure of the telescope. We also estimate line-of-sight PWVs of each skydip observation using the frequency response of MKIDs, and confirm the consistency with PWVs reported by the Atacama Large Millimeter/submillimeter Array.
△ Less
Submitted 15 January, 2020;
originally announced January 2020.
-
An Ultra-Wideband Leaky Lens Antenna for Broadband Spectroscopic Imaging Applications
Authors:
Sebastian Hähnle,
Ozan Yurduseven,
Sven van Berkel,
Nuria Llombart,
Juan Bueno,
Stephen J. C. Yates,
Vignesh Murugesan,
David J. Thoen,
Andrea Neto,
Jochem J. A. Baselmans
Abstract:
We present the design, fabrication and characterisation of a broadband leaky lens antenna for broadband, spectroscopic imaging applications. The antenna is designed for operation in the 300-900 GHz band. We integrate the antenna directly into an Al-NbTiN hybrid MKID to measure the beam pattern and absolute coupling efficiency at three frequency bands centred around 350, 650 and 850 GHz, covering t…
▽ More
We present the design, fabrication and characterisation of a broadband leaky lens antenna for broadband, spectroscopic imaging applications. The antenna is designed for operation in the 300-900 GHz band. We integrate the antenna directly into an Al-NbTiN hybrid MKID to measure the beam pattern and absolute coupling efficiency at three frequency bands centred around 350, 650 and 850 GHz, covering the full antenna band. We find an aperture efficiency $η_{ap} \approx 0.4$ over the whole frequency band, limited by lens reflections. We find a good match with simulations for both the patterns and efficiency, demonstrating a 1:3 bandwidth in the sub-mm wavelength range for future on-chip spectrometers.
△ Less
Submitted 16 December, 2019;
originally announced December 2019.
-
First light demonstration of the integrated superconducting spectrometer
Authors:
Akira Endo,
Kenichi Karatsu,
Yoichi Tamura,
Tai Oshima,
Akio Taniguchi,
Tatsuya Takekoshi,
Shin'ichiro Asayama,
Tom J. L. C. Bakx,
Sjoerd Bosma,
Juan Bueno,
Kah Wuy Chin,
Yasunori Fujii,
Kazuyuki Fujita,
Robert Huiting,
Soh Ikarashi,
Tsuyoshi Ishida,
Shun Ishii,
Ryohei Kawabe,
Teun M. Klapwijk,
Kotaro Kohno,
Akira Kouchi,
Nuria Llombart,
Jun Maekawa,
Vignesh Murugesan,
Shunichi Nakatsubo
, et al. (14 additional authors not shown)
Abstract:
Ultra-wideband 3D imaging spectrometry in the millimeter-submillimeter (mm-submm) band is an essential tool for uncovering the dust-enshrouded portion of the cosmic history of star formation and galaxy evolution. However, it is challenging to scale up conventional coherent heterodyne receivers or free-space diffraction techniques to sufficient bandwidths ($\geq$1 octave) and numbers of spatial pix…
▽ More
Ultra-wideband 3D imaging spectrometry in the millimeter-submillimeter (mm-submm) band is an essential tool for uncovering the dust-enshrouded portion of the cosmic history of star formation and galaxy evolution. However, it is challenging to scale up conventional coherent heterodyne receivers or free-space diffraction techniques to sufficient bandwidths ($\geq$1 octave) and numbers of spatial pixels (>$10^2$). Here we present the design and first astronomical spectra of an intrinsically scalable, integrated superconducting spectrometer, which covers 332-377 GHz with a spectral resolution of $F/ΔF \sim 380$. It combines the multiplexing advantage of microwave kinetic inductance detectors (MKIDs) with planar superconducting filters for dispersing the signal in a single, small superconducting integrated circuit. We demonstrate the two key applications for an instrument of this type: as an efficient redshift machine, and as a fast multi-line spectral mapper of extended areas. The line detection sensitivity is in excellent agreement with the instrument design and laboratory performance, reaching the atmospheric foreground photon noise limit on sky. The design can be scaled to bandwidths in excess of an octave, spectral resolution up to a few thousand and frequencies up to $\sim$1.1 THz. The miniature chip footprint of a few $\mathrm{cm^2}$ allows for compact multi-pixel spectral imagers, which would enable spectroscopic direct imaging and large volume spectroscopic surveys that are several orders of magnitude faster than what is currently possible.
△ Less
Submitted 18 September, 2019; v1 submitted 24 June, 2019;
originally announced June 2019.
-
Wideband on-chip terahertz spectrometer based on a superconducting filterbank
Authors:
Akira Endo,
Kenichi Karatsu,
Alejandro Pascual Laguna,
Behnam Mirzaei,
Robert Huiting,
David J. Thoen,
Vignesh Murugesan,
Stephen J. C. Yates,
Juan Bueno,
Nuri van Marrewijk,
Sjoerd Bosma,
Ozan Yurduseven,
Nuria Llombart,
Junya Suzuki,
Masato Naruse,
Pieter J. de Visser,
Paul P. van der Werf,
Teun M. Klapwijk,
Jochem J. A. Baselmans
Abstract:
Terahertz spectrometers with a wide instantaneous frequency coverage for passive remote sensing are enormously attractive for many terahertz applications, such as astronomy, atmospheric science and security. Here we demonstrate a wide-band terahertz spectrometer based on a single superconducting chip. The chip consists of an antenna coupled to a transmission line filterbank, with a microwave kinet…
▽ More
Terahertz spectrometers with a wide instantaneous frequency coverage for passive remote sensing are enormously attractive for many terahertz applications, such as astronomy, atmospheric science and security. Here we demonstrate a wide-band terahertz spectrometer based on a single superconducting chip. The chip consists of an antenna coupled to a transmission line filterbank, with a microwave kinetic inductance detector behind each filter. Using frequency division multiplexing, all detectors are read-out simultaneously creating a wide-band spectrometer with an instantaneous bandwidth of 45 GHz centered around 350 GHz. The spectrometer has a spectral resolution of $F/ΔF=380$ and reaches photon-noise limited sensitivity. We discuss the chip design and fabrication, as well as the system integration and testing. We confirm full system operation by the detection of an emission line spectrum of methanol gas. The proposed concept allows for spectroscopic radiation detection over large bandwidths and resolutions up to $F/ΔF\sim1000$, all using a chip area of a few $\mathrm{cm^2}$. This will allow the construction of medium resolution imaging spectrometers with unprecedented speed and sensitivity.
△ Less
Submitted 21 June, 2019; v1 submitted 21 January, 2019;
originally announced January 2019.
-
Mitigation of Cosmic Ray Effect on Microwave Kinetic Inductance Detector Arrays
Authors:
K. Karatsu,
A. Endo,
J. Bueno,
P. J. de Visser,
R. Barends,
D. J. Thoen,
V. Murugesan,
N. Tomita,
J. J. A. Baselmans
Abstract:
For space observatories, the glitches caused by high energy phonons created by the interaction of cosmic ray particles with the detector substrate lead to dead time during observation. Mitigating the impact of cosmic rays is therefore an important requirement for detectors to be used in future space missions. In order to investigate possible solutions, we carry out a systematic study by testing fo…
▽ More
For space observatories, the glitches caused by high energy phonons created by the interaction of cosmic ray particles with the detector substrate lead to dead time during observation. Mitigating the impact of cosmic rays is therefore an important requirement for detectors to be used in future space missions. In order to investigate possible solutions, we carry out a systematic study by testing four large arrays of Microwave Kinetic Inductance Detectors (MKIDs), each consisting of $\sim$960 pixels and fabricated on monolithic 55 mm $\times$ 55 mm $\times$ 0.35 mm Si substrates. We compare the response to cosmic ray interactions in our laboratory for different detector arrays: A standard array with only the MKID array as reference; an array with a low $T_c$ superconducting film as phonon absorber on the opposite side of the substrate; and arrays with MKIDs on membranes. The idea is that the low $T_c$ layer down-converts the phonon energy to values below the pair breaking threshold of the MKIDs, and the membranes isolate the sensitive part of the MKIDs from phonons created in the substrate. We find that the dead time can be reduced up to a factor of 40 when compared to the reference array. Simulations show that the dead time can be reduced to below 1 % for the tested detector arrays when operated in a spacecraft in an L2 or a similar far-Earth orbit. The technique described here is also applicable and important for large superconducting qubit arrays for future quantum computers.
△ Less
Submitted 10 January, 2019; v1 submitted 8 January, 2019;
originally announced January 2019.
-
Eliminating stray radiation inside large area imaging arrays
Authors:
Stephen J. C. Yates,
Simon Doyle,
Peter Barry,
Andrey M. Baryshev,
Juan Bueno,
Lorenza Ferrari,
Nuria Llombart,
Vignesh Murugesan,
David J. Thoen,
Ozan Yurduseven,
Jochem J. A. Baselmans
Abstract:
With increasing array size, it is increasingly important to control stray radiation inside the detector chips themselves. We demonstrate this effect with focal plane arrays of absorber coupled Lumped Element microwave Kinetic Inductance Detectors (LEKIDs) and lens-antenna coupled distributed quarter wavelength Microwave Kinetic Inductance Detectors (MKIDs). In these arrays the response from a poin…
▽ More
With increasing array size, it is increasingly important to control stray radiation inside the detector chips themselves. We demonstrate this effect with focal plane arrays of absorber coupled Lumped Element microwave Kinetic Inductance Detectors (LEKIDs) and lens-antenna coupled distributed quarter wavelength Microwave Kinetic Inductance Detectors (MKIDs). In these arrays the response from a point source at the pixel position is at a similar level to the stray response integrated over the entire chip area. For the antenna coupled arrays, we show that this effect can be suppressed by incorporating an on-chip stray light absorber. A similar method should be possible with the LEKID array, especially when they are lens coupled.
△ Less
Submitted 11 September, 2018;
originally announced September 2018.
-
Surface wave control for large arrays of microwave kinetic inductance detectors
Authors:
Stephen J. C. Yates,
Andrey M. Baryshev,
Ozan Yurduseven,
Juan Bueno,
Kristina K. Davis,
Lorenza Ferrari,
Willem Jellema,
Nuria Llombart,
Vignesh Murugesan,
David J. Thoen,
Jochem J. A. Baselmans
Abstract:
Large ultra-sensitive detector arrays are needed for present and future observatories for far infra-red, submillimeter wave (THz), and millimeter wave astronomy. With increasing array size, it is increasingly important to control stray radiation inside the detector chips themselves, the surface wave. We demonstrate this effect with focal plane arrays of 880 lens-antenna coupled Microwave Kinetic I…
▽ More
Large ultra-sensitive detector arrays are needed for present and future observatories for far infra-red, submillimeter wave (THz), and millimeter wave astronomy. With increasing array size, it is increasingly important to control stray radiation inside the detector chips themselves, the surface wave. We demonstrate this effect with focal plane arrays of 880 lens-antenna coupled Microwave Kinetic Inductance Detectors (MKIDs). Presented here are near field measurements of the MKID optical response versus the position on the array of a reimaged optical source. We demonstrate that the optical response of a detector in these arrays saturates off-pixel at the $\sim-30$ dB level compared to the peak pixel response. The result is that the power detected from a point source at the pixel position is almost identical to the stray response integrated over the chip area. With such a contribution, it would be impossible to measure extended sources, while the point source sensitivity is degraded due to an increase of the stray loading. However, we show that by incorporating an on-chip stray light absorber, the surface wave contribution is reduced by a factor $>$10. With the on-chip stray light absorber the point source response is close to simulations down to the $\sim-35$ dB level, the simulation based on an ideal Gaussian illumination of the optics. In addition, as a crosscheck we show that the extended source response of a single pixel in the array with the absorbing grid is in agreement with the integral of the point source measurements.
△ Less
Submitted 7 July, 2017;
originally announced July 2017.
-
Experimentally simulating the dynamics of quantum light and matter at ultrastrong coupling
Authors:
N. K. Langford,
R. Sagastizabal,
M. Kounalakis,
C. Dickel,
A. Bruno,
F. Luthi,
D. J. Thoen,
A. Endo,
L. DiCarlo
Abstract:
The quantum Rabi model describing the fundamental interaction between light and matter is a cornerstone of quantum physics. It predicts exotic phenomena like quantum phase transitions and ground-state entanglement in the ultrastrong-coupling (USC) regime, where coupling strengths are comparable to subsystem energies. Despite progress in many experimental platforms, the few experiments reaching USC…
▽ More
The quantum Rabi model describing the fundamental interaction between light and matter is a cornerstone of quantum physics. It predicts exotic phenomena like quantum phase transitions and ground-state entanglement in the ultrastrong-coupling (USC) regime, where coupling strengths are comparable to subsystem energies. Despite progress in many experimental platforms, the few experiments reaching USC have been limited to spectroscopy: demonstrating USC dynamics remains an outstanding challenge. Here, we employ a circuit QED chip with moderate coupling between a resonator and transmon qubit to realise accurate digital quantum simulation of USC dynamics. We advance the state of the art in solid-state digital quantum simulation by using up to 90 second-order Trotter steps and probing both subsystems in a combined Hilbert space dimension $\sim80$, demonstrating the Schrödinger-cat like entanglement and build-up of large photon numbers characteristic of deep USC. This work opens the door to exploring extreme USC regimes, quantum phase transitions and many-body effects in the Dicke model.
△ Less
Submitted 31 October, 2016;
originally announced October 2016.
-
A kilo-pixel imaging system for future space based far-infrared observatories using microwave kinetic inductance detectors
Authors:
J. J. A. Baselmans,
J. Bueno,
S. J. C. Yates,
O. Yurduseven,
N. Llombart,
K. Karatsu,
A. M. Baryshev,
L. Ferrari,
A. Endo,
D. J. Thoen,
P. J. de Visser,
R. M. J. Janssen,
V. Murugesan,
E. F. C. Driessen,
G. Coiffard,
J. Martin-Pintado,
P. Hargrave,
M. Griffin
Abstract:
Future astrophysics and cosmic microwave background space missions operating in the far-infrared to millimetre part of the spectrum will require very large arrays of ultra-sensitive detectors in combination with high multiplexing factors and efficient low-noise and low-power readout systems. We have developed a demonstrator system suitable for such applications. The system combines a 961 pixel ima…
▽ More
Future astrophysics and cosmic microwave background space missions operating in the far-infrared to millimetre part of the spectrum will require very large arrays of ultra-sensitive detectors in combination with high multiplexing factors and efficient low-noise and low-power readout systems. We have developed a demonstrator system suitable for such applications. The system combines a 961 pixel imaging array based upon Microwave Kinetic Inductance Detectors (MKIDs) with a readout system capable of reading out all pixels simultaneously with only one readout cable pair and a single cryogenic amplifier. We evaluate, in a representative environment, the system performance in terms of sensitivity, dynamic range, optical efficiency, cosmic ray rejection, pixel-pixel crosstalk and overall yield at at an observation centre frequency of 850 GHz and 20% fractional bandwidth. The overall system has an excellent sensitivity, with an average detector sensitivity NEPdet=3x10^-19 W/rt(Hz) measured using a thermal calibration source. At a loading power per pixel of 50fW we demonstrate white, photon noise limited detector noise down to 300 mHz. The dynamic range would allow the detection of 1 Jy bright sources within the field of view without tuning the readout of the detectors. The expected dead time due to cosmic ray interactions, when operated in an L2 or a similar far-Earth orbit, is found to be <4%. Additionally, the achieved pixel yield is 83% and the crosstalk between the pixels is <-30dB. This demonstrates that MKID technology can provide multiplexing ratios on the order of a 1000 with state-of-the-art single pixel performance, and that the technology is now mature enough to be considered for future space based observatories and experiments.
△ Less
Submitted 1 March, 2017; v1 submitted 7 September, 2016;
originally announced September 2016.
-
Superconducting NbTiN Thin Films with Highly Uniform Properties over a 100 mm diameter Wafer
Authors:
D. J. Thoen,
B. G. C. Bos,
E. A. F. Haalebos,
T. M. Klapwijk,
J. J. A. Baselmans,
A. Endo
Abstract:
Uniformity in thickness and electronic properties of superconducting niobium titanium nitride (NbTiN) thin films is a critical issue for upscaling superconducting electronics, such as microwave kinetic inductance detectors for submillimeter wave astronomy. In this article we make an experimental comparison between the uniformity of NbTiN thin films produced by two DC magnetron sputtering systems w…
▽ More
Uniformity in thickness and electronic properties of superconducting niobium titanium nitride (NbTiN) thin films is a critical issue for upscaling superconducting electronics, such as microwave kinetic inductance detectors for submillimeter wave astronomy. In this article we make an experimental comparison between the uniformity of NbTiN thin films produced by two DC magnetron sputtering systems with vastly different target sizes: the Nordiko 2000 equipped with a circular 100mm diameter target, and the Evatec LLS801 with a rectangular target of 127 mm x 444.5 mm. In addition to the films deposited staticly in both systems, we have also deposited films in the LLS801 while shuttling the substrate in front of the target, with the aim of further enhancing the uniformity. Among these three setups, the LLS801 system with substrate shuttling has yielded the highest uniformity in film thickness (+/-2%), effective resistivity (decreasing by 5% from center to edge), and superconducting critical temperature (T_c = 15.0 K - 15.3 K) over a 100 mm diameter wafer. However, the shuttling appears to increase the resistivity by almost a factor of 2 compared to static deposition. Surface SEM inspections suggest that the shuttling could have induced a different mode of microstructural film growth.
△ Less
Submitted 22 November, 2016; v1 submitted 6 September, 2016;
originally announced September 2016.
-
Reactive magnetron sputter deposition of superconducting niobium titanium nitride thin films with different target sizes
Authors:
B. G. C. Bos,
D. J. Thoen,
E. A. F. Haalebos,
P. M. L. Gimbel,
T. M. Klapwijk,
J. J. A. Baselmans,
A. Endo
Abstract:
The superconducting critical temperature (Tc > 15K) of niobium titanium nitride (NbTiN) thin films allows for low-loss circuits up to 1.1 THz, enabling on-chip spectroscopy and multi-pixel imaging with advanced detectors. The drive for large scale detector microchips is demanding NbTiN films with uniform properties over an increasingly larger area. This article provides an experimental comparison…
▽ More
The superconducting critical temperature (Tc > 15K) of niobium titanium nitride (NbTiN) thin films allows for low-loss circuits up to 1.1 THz, enabling on-chip spectroscopy and multi-pixel imaging with advanced detectors. The drive for large scale detector microchips is demanding NbTiN films with uniform properties over an increasingly larger area. This article provides an experimental comparison between two reactive d.c. sputter systems with different target sizes: a small target (100mm diameter) and a large target (127 mm x 444.5 mm). This article focuses on maximizing the Tc of the films and the accompanying I-V characteristics of the sputter plasma, and we find that both systems are capable of depositing films with Tc > 15 K. The resulting film uniformity is presented in a second manuscript in this volume. We find that these films are deposited within the transition from metallic to compound sputtering, at the point where target nitridation most strongly depends on nitrogen flow. Key in the deposition optimization is to increase the system's pum** speed and gas flows to counteract the hysteretic effects induced by the target size. Using the I-V characteristics as a guide proves to be an effective way to optimize a reactive sputter system, for it can show whether the optimal deposition regime is hysteresis-free and accessible.
△ Less
Submitted 22 November, 2016; v1 submitted 5 September, 2016;
originally announced September 2016.
-
Probing the Nuclear Spin-Lattice Relaxation Time at the Nanoscale
Authors:
J. J. T. Wagenaar,
A. M. J. den Haan,
J. M. de Voogd,
L. Bossoni,
T. A. de Jong,
M. de Wit,
K. M. Bastiaans,
D. J. Thoen,
A. Endo,
T. M. Klapwijk,
J. Zaanen,
T. H. Oosterkamp
Abstract:
Nuclear spin-lattice relaxation times are measured on copper using magnetic resonance force microscopy performed at temperatures down to 42 mK. The low temperature is verified by comparison with the Korringa relation. Measuring spin-lattice relaxation times locally at very low temperatures opens up the possibility to measure the magnetic properties of inhomogeneous electron systems realized in oxi…
▽ More
Nuclear spin-lattice relaxation times are measured on copper using magnetic resonance force microscopy performed at temperatures down to 42 mK. The low temperature is verified by comparison with the Korringa relation. Measuring spin-lattice relaxation times locally at very low temperatures opens up the possibility to measure the magnetic properties of inhomogeneous electron systems realized in oxide interfaces, topological insulators and other strongly correlated electron systems such as high-Tc superconductors.
△ Less
Submitted 27 June, 2016; v1 submitted 14 March, 2016;
originally announced March 2016.
-
On-chip filter bank spectroscopy at 600-700 GHz using NbTiN superconducting resonators
Authors:
A. Endo,
C. Sfiligoj,
S. J. C. Yates,
J. J. A. Baselmans,
D. J. Thoen,
S. M. H. Javadzadeh,
P. P. van der Werf,
A. M. Baryshev,
T. M. Klapwijk
Abstract:
We experimentally demonstrate the principle of an on-chip submillimeter wave filter bank spectrometer, using superconducting microresonators as narrow band-separation filters. The filters are made of NbTiN/SiNx/NbTiN microstrip line resonators, which have a resonance frequency in the range of 614-685 GHz---two orders of magnitude higher in frequency than what is currently studied for use in circui…
▽ More
We experimentally demonstrate the principle of an on-chip submillimeter wave filter bank spectrometer, using superconducting microresonators as narrow band-separation filters. The filters are made of NbTiN/SiNx/NbTiN microstrip line resonators, which have a resonance frequency in the range of 614-685 GHz---two orders of magnitude higher in frequency than what is currently studied for use in circuit quantum electrodynamics and photodetectors. The frequency resolution of the filters decreases from 350 to 140 with increasing frequency, most likely limited by dissipation of the resonators.
△ Less
Submitted 21 June, 2013; v1 submitted 28 March, 2013;
originally announced March 2013.
-
Probing dynamics of an electron-spin ensemble via a superconducting resonator
Authors:
V. Ranjan,
G. de Lange,
R. Schutjens,
T. Debelhoir,
J. P. Groen,
D. Szombati,
D. J. Thoen,
T. M. Klapwijk,
R. Hanson,
L. DiCarlo
Abstract:
We study spin relaxation and diffusion in an electron-spin ensemble of nitrogen impurities in diamond at low temperature (0.25-1.2 K) and polarizing magnetic field (80-300 mT). Measurements exploit mode- and temperature-dependent coupling of hyperfine-split sub-ensembles to the resonator. Temperature-independent spin linewidth and relaxation time suggest that spin diffusion limits spin relaxation.…
▽ More
We study spin relaxation and diffusion in an electron-spin ensemble of nitrogen impurities in diamond at low temperature (0.25-1.2 K) and polarizing magnetic field (80-300 mT). Measurements exploit mode- and temperature-dependent coupling of hyperfine-split sub-ensembles to the resonator. Temperature-independent spin linewidth and relaxation time suggest that spin diffusion limits spin relaxation. Depolarization of one sub-ensemble by resonant pum** of another indicates fast cross-relaxation compared to spin diffusion, with implications on use of sub-ensembles as independent quantum memories.
△ Less
Submitted 27 August, 2012;
originally announced August 2012.
