-
On the complete interface development of Al/Cu magnetic pulse welding via experimental characterizations and multiphysics numerical simulations
Authors:
J. S. Li,
T. Sapanathan,
R. N. Raoelison,
Y. L. Hou,
A. Simar,
M. Rachik
Abstract:
A complex Al/Cu magnetic pulse welding interface is systematically investigated using experimental characterizations and numerical simulations. A Coupled electromagnetic-mechanical simulation is proposed to compute the impact velocity and impact angle along the entire interface. This model allows to further understand the formation mechanism of various interface characteristics during MPW. The res…
▽ More
A complex Al/Cu magnetic pulse welding interface is systematically investigated using experimental characterizations and numerical simulations. A Coupled electromagnetic-mechanical simulation is proposed to compute the impact velocity and impact angle along the entire interface. This model allows to further understand the formation mechanism of various interface characteristics during MPW. The results revealed that the impact velocity gradually decreases in conjunction with the gradual increase of the impact angle. These simulations elucidate the experimentally observed successive interface morphologies, i.e., the unwelded zone, vortex zone, intermediate (IM) layers and wavy interface. Microstructural characterizations show that the IM layers are formed by mechanical mixing combined with melting and are characterized by highly heterogeneous porous zone with random sizes and distributions of void. Subsequently, an Eulerian simulation is proposed to investigate the thermomechanical effects during the wave formation which vastly influence the joint quality. The predicted wavy morphologies, temperature distribution and average equivalent plastic strain along the interface provided a better understanding on the formation steps of the experimentally observed wave morphologies. The actual kinematics during wave generation revealed that the wave was formed with repeated deformation of the interface material. The wave amplitude increases with increasing jetting angle; while the wavelength increases with increasing collision point velocity.
△ Less
Submitted 27 April, 2021;
originally announced April 2021.
-
Combined numerical and experimental estimation of the fracture toughness and failure analysis of single lap shear test for dissimilar welds
Authors:
Norberto Jimenez Mena,
Thaneshan Sapanathan,
Pascal J. Jacques,
Aude Simar
Abstract:
The single lap shear test is widely used to measure the strength of dissimilar welds even though such a test brings limited understanding of the intrinsic weld toughness. The present study proposes a numerical finite element (FE) analysis and experimental characterization of dissimilar joints presenting various microstructures (thickness of the intermetallic layer (IML) and hardness profile). For…
▽ More
The single lap shear test is widely used to measure the strength of dissimilar welds even though such a test brings limited understanding of the intrinsic weld toughness. The present study proposes a numerical finite element (FE) analysis and experimental characterization of dissimilar joints presenting various microstructures (thickness of the intermetallic layer (IML) and hardness profile). For this purpose, Friction Melt Bonding (FMB) and Friction Stir Welding (FSW) were used to join aluminum AA6061 and Dual Phase steel (DP980). The FE simulations allowed calculating the evolution of the J-integral near this notch tip. It shows that crack initiation depends significantly on the plastic properties of the welded metallic alloys around the notch tip and the width of the welded zone, which both are significantly different for FSW and FMB processes. Nevertheless, a similar weld fracture toughness J_C of approximately 1 kJ.m-2 is estimated from the analysis for both FMB and FSW. This is three orders of magnitude higher than the fracture toughness of the intermetallic layer, revealing that the plastic dissipation in the Al and steel plates around the crack tip has a major effect on the weld toughness.
△ Less
Submitted 27 April, 2021;
originally announced April 2021.
-
A new physical simulation tool to predict the interface of dissimilar aluminum to steel welds performed by Friction Melt Bonding
Authors:
T. Sapanathan,
N. Jimenez-Mena,
I. Sabirov,
M. A. Monclus,
J. M. Molina-Aldareguia,
P. Xia,
L. Zhao,
A. Simar
Abstract:
Optimization of the intermetallic layer thickness and the suppression of interfacial defects are key elements to improve the load bearing capacity of dissimilar joints. However, till date we do not have a systematic tool to investigate the dissimilar joints and the intermetallic properties produced by a welding condition. Friction Melt Bonding (FMB) is a recently developed technique for joining di…
▽ More
Optimization of the intermetallic layer thickness and the suppression of interfacial defects are key elements to improve the load bearing capacity of dissimilar joints. However, till date we do not have a systematic tool to investigate the dissimilar joints and the intermetallic properties produced by a welding condition. Friction Melt Bonding (FMB) is a recently developed technique for joining dissimilar metals that also does not exempt to these challenges. The FMB of DP980 and Al6061-T6 is investigated using a new physical simulation tool, based on Gleeble thermo-mechanical simulator, to understand the effect of individual parameter on the intermetallic formation. The proposed method demonstrates its capability in reproducing the intermetallic characteristics, including the thickness of intermetallic bonding layer, the morphology and texture of its constituents (Fe2Al5 and Fe4Al13), as well as their nanohardness and reduced modulus. The advantages of physical simulation tool can enable novel develo** routes for the development of dissimilar metal joining processes and facilitate to reach the requiring load bearing capacity of the joints.
△ Less
Submitted 1 April, 2021;
originally announced April 2021.
-
High temperature in situ SEM assessment followed by ex situ AFM and EBSD investigation of the nucleation and early growth stages of Fe-Al intermetallics
Authors:
T. Sapanathan,
I. Sabirov,
P. Xia,
M. A. Monclus,
J. M. Molina-Aldareguia,
P. J. Jacques,
A. Simar
Abstract:
A dedicated in situ heating setup in a scanning electron microscope (SEM) followed by an ex situ atomic force microscopy (AFM) and electron backscatter diffraction (EBSD) is used to characterize the nucleation and early growth stages of Fe-Al intermetallics (IMs) at 596 °C. A location tracking is used to interpret further characterization. Ex situ AFM observations reveal a slight shrinkage and out…
▽ More
A dedicated in situ heating setup in a scanning electron microscope (SEM) followed by an ex situ atomic force microscopy (AFM) and electron backscatter diffraction (EBSD) is used to characterize the nucleation and early growth stages of Fe-Al intermetallics (IMs) at 596 °C. A location tracking is used to interpret further characterization. Ex situ AFM observations reveal a slight shrinkage and out of plane protrusion of the IM at the onset of IM nucleation followed by directional growth. The formed interfacial IM compounds were identified by ex situ EBSD. It is now clearly demonstrated that the θ-phase nucleates first prior to the diffusion-controlled growth of the η-phase. The θ-phase prevails the intermetallic layer.
△ Less
Submitted 31 March, 2021;
originally announced March 2021.
