-
Freezing of sessile droplet and frost halo formation
Authors:
Sivanandan Kavuri,
George Karapetsas,
Chander Shekhar Sharma,
Kirti Chandra Sahu
Abstract:
The freezing of a sessile droplet unveils fascinating physics, characterised by the emergence of a frost halo on the underlying substrate, the progression of the liquid-ice interface, and the formation of a cusp-like morphology at the tip of the droplet. We investigate the freezing of a volatile sessile droplet, focusing on the frost halo formation, which has not been theoretically explored. The f…
▽ More
The freezing of a sessile droplet unveils fascinating physics, characterised by the emergence of a frost halo on the underlying substrate, the progression of the liquid-ice interface, and the formation of a cusp-like morphology at the tip of the droplet. We investigate the freezing of a volatile sessile droplet, focusing on the frost halo formation, which has not been theoretically explored. The formation of the frost halo is associated with the inherent evaporation process in the early freezing stages. We observe a negative evaporation flux envelo** the droplet in the initial stages, which indicates that vapour produced during freezing condenses on the substrate close to the contact line, forming a frost halo. The condensate accumulation triggers re-evaporation, resulting in a temporal shift of the frost halo region away from the contact line. Eventually, it disappears due to the diffusive nature of the water vapour far away from the droplet. We found that increasing the relative humidity increases the lifetime of the frost halo due to a substantial reduction in evaporation that prolonged the presence of net condensate on the substrate. Increasing liquid volatility increases the evaporation flux, and condensation occurs closer to the droplet, as a higher amount of vapour is in the periphery of the droplet. We also found that decreasing the thermal conductivity of the substrate increases the total freezing time. The slower freezing process is accompanied by increased vaporized liquid, resulting in condensation with its concentration reaching supersaturation.
△ Less
Submitted 5 December, 2023;
originally announced December 2023.
-
Condensate droplet roaming on nanostructured superhydrophobic surfaces
Authors:
Cheuk Wing Edmond Lam,
Kartik Regulagadda,
Matteo Donati,
Abinash Tripathy,
Gopal Chandra Pal,
Chander Shekhar Sharma,
Athanasios Milionis,
Dimos Poulikakos
Abstract:
Jum** of coalescing condensate droplets from superhydrophobic surfaces is an interesting phenomenon which yields marked heat transfer enhancement over the more explored gravity-driven droplet removal mode in surface condensation, a phase change process of central interest to applications ranging from energy to water harvesting. However, when condensate microdroplets coalesce, they can also spont…
▽ More
Jum** of coalescing condensate droplets from superhydrophobic surfaces is an interesting phenomenon which yields marked heat transfer enhancement over the more explored gravity-driven droplet removal mode in surface condensation, a phase change process of central interest to applications ranging from energy to water harvesting. However, when condensate microdroplets coalesce, they can also spontaneously propel themselves omnidirectionally on the surface independent of gravity and grow by feeding from droplets they sweep along the way. Here we observe and explain the physics behind this phenomenon of roaming of coalescing condensate microdroplets on solely nanostructured superhydrophobic surfaces, where the microdroplets are orders of magnitude larger than the underlaying surface nanotexture. We quantify and show that it is the inherent asymmetries in droplet adhesion during condensation, arising from the stochastic nature of nucleation within the nanostructures, that generates the tangential momentum driving the roaming motion. Subsequent dewetting during this conversion initiates a vivid roaming and successive coalescence process, preventing condensate flooding of the surface, and enhancing surface renewal. Finally, we show that the more efficient conversion process of roaming from excess surface energy to kinetic energy results in significantly improved heat transfer efficiency over condensate droplet jum**, the mechanism currently understood as maximum.
△ Less
Submitted 17 October, 2023;
originally announced October 2023.
-
Controlled coalescence-induced droplet jum** on flexible superhydrophobic substrates
Authors:
Gopal Chandra Pal,
Siddharth SS,
Manish Agarwal,
Chander Shekhar Sharma
Abstract:
Sessile droplets coalescing on superhydrophobic substrates spontaneously jump from the surface. In this process, the excess surface energy available at the initiation of coalescence overcomes the minimal surface adhesion and manifests as sufficient kinetic energy to propel the droplets away from the substrate. Here, we show that the coalescence induced droplet jum** velocity is significantly cur…
▽ More
Sessile droplets coalescing on superhydrophobic substrates spontaneously jump from the surface. In this process, the excess surface energy available at the initiation of coalescence overcomes the minimal surface adhesion and manifests as sufficient kinetic energy to propel the droplets away from the substrate. Here, we show that the coalescence induced droplet jum** velocity is significantly curtailed if the superhydrophobic substrate is flexible in nature. Through detailed experimental measurements and numerical simulations, we demonstrate that the droplet jum** velocity and jum** height can be reduced by as much as 40 % and 64%, respectively, by synergistically tuning the substrate stiffness and substrate frequency. We show that this hitherto unexplored aspect of droplet coalescence jum** can be gainfully exploited in water harvesting from dew and fog harvesting. Additionally, through an exemplar butterfly wing substrate, we demonstrate that this effect is likely to manifest on many natural superhydrophobic substrates due to their inherent flexibility.
△ Less
Submitted 11 April, 2023;
originally announced April 2023.
-
Biomimetic Micropillar Wick for Enhanced Thin-Film Evaporation
Authors:
Anand S,
Chander Shekhar Sharma
Abstract:
Sustainable liquid cooling solutions are recognized as the future of thermal management in the chip industry. Among them, the phase change heat transfer devices such as heat pipes and vapour chambers have shown tremendous potential. These devices rely on the physics of capillary-driven thin-film evaporation which is inherently coupled with the design and optimization of the evaporator wicks used i…
▽ More
Sustainable liquid cooling solutions are recognized as the future of thermal management in the chip industry. Among them, the phase change heat transfer devices such as heat pipes and vapour chambers have shown tremendous potential. These devices rely on the physics of capillary-driven thin-film evaporation which is inherently coupled with the design and optimization of the evaporator wicks used in these devices. Here, we introduce a biomimetic evaporator wick design inspired by the peristome of the Nepenthes alata that can achieve significantly enhanced evaporative cooling. It consists of array of micropillars with multiple wedges along the sidewall of each micropillar. The efficacy of the wedged micropillar is evaluated based on a validated numerical model on the metrics of dryout heat flux and effective heat transfer coefficient. The wedge angle is chosen such that wedged micropillars cause liquid filaments to rise along the micropillar vertical walls. This results in a significant increase in thin-film area for evaporation. Additionally, the large mean curvature of the liquid meniscus produces strong capillary pum** pressure and simultaneously, the wedges increase the overall permeability of the wick. Consequently, our model predicts that the wedged micropillar wick can attain ~234% enhancement of dryout heat flux compared to a conventional cylindrical micropillar wick of similar geometrical dimensions. Moreover, the wedged micropillars can also attain higher effective heat transfer coefficient under dryout conditions thus outperforming the cylindrical micropillar in terms of heat transfer efficiency. Our study provide insight into the design and capability of the biomimetic wedged micropillars as an efficient evaporator wick for various thin-film evaporation applications.
△ Less
Submitted 9 February, 2023;
originally announced February 2023.
-
Out-of-Plane Biphilic Surface Structuring for Enhanced Capillary-Driven Dropwise Condensation
Authors:
Luca Stendardo,
Athanasios Milionis,
George Kokkoris,
Christos Stamatopoulos,
Chander Shekhar Sharma,
Raushan Kumar,
Matteo Donati,
Dimos Poulikakos
Abstract:
Rapid and sustained condensate droplet departure from a surface is key towards achieving high heat transfer rates in condensation, a physical process critical to a broad range of industrial and societal applications. Despite progress in enhancing condensation heat transfer through inducing its dropwise mode with hydrophobic materials, sophisticated surface engineering methods that can lead to furt…
▽ More
Rapid and sustained condensate droplet departure from a surface is key towards achieving high heat transfer rates in condensation, a physical process critical to a broad range of industrial and societal applications. Despite progress in enhancing condensation heat transfer through inducing its dropwise mode with hydrophobic materials, sophisticated surface engineering methods that can lead to further enhancement of heat transfer are still highly desirable. Here, by employing a three-dimensional, multiphase computational approach, we present an effective out-of-plane biphilic surface topography, that reveals an unexplored capillarity-driven departure mechanism of condensate droplets. This texture consists of biphilic diverging micro-cavities wherein a matrix of small hydrophilic spots is placed at their bottom, that is, amongst the pyramid-shaped, superhydrophobic micro-textures forming the cavities. We show that an optimal combination of the hydrophilic spots and the angles of the pyramidal structures can achieve high deformational stretching of the droplets, eventually realizing an impressive slingshot-like droplet ejection process from the texture. Such a droplet departure mechanism has the potential to reduce the droplet ejection volume and thus enhance the overall condensation efficiency, compared to coalescence-initiated droplet jum** from other state-of-the-art surfaces. Simulations have shown that optimal pyramid-shaped biphilic micro-structures can provoke droplet self-ejection at low volumes, up to 56% lower compared to superhydrophobic straight pillars, revealing a promising new surface micro-texture design strategy towards enhancing condensation heat transfer efficiency and water harvesting capabilities.
△ Less
Submitted 5 November, 2022;
originally announced November 2022.
-
Enhancing condensation on soft substrates through bulk lubricant infusion
Authors:
Chander Shekhar Sharma,
Athanasios Milionis,
Abhinav Naga,
Cheuk Wing Edmond Lam,
Gabriel Rodriguez,
Marco Francesco Del Ponte,
Valentina Negri,
Hopf Raoul,
Maria D'Acunzi,
Hans-Jürgen Butt,
Doris Vollmer,
Dimos Poulikakos
Abstract:
Soft substrates such as polydimethylsiloxane (PDMS) enhance droplet nucleation during the condensation of water vapour, because their deformability inherently reduces the energetic threshold for heterogeneous nucleation relative to rigid substrates. However, this enhanced droplet nucleation is counteracted later in the condensation cycle, when the viscoelastic dissipation inhibits condensate dropl…
▽ More
Soft substrates such as polydimethylsiloxane (PDMS) enhance droplet nucleation during the condensation of water vapour, because their deformability inherently reduces the energetic threshold for heterogeneous nucleation relative to rigid substrates. However, this enhanced droplet nucleation is counteracted later in the condensation cycle, when the viscoelastic dissipation inhibits condensate droplet shedding from the substrate. Here, we show that bulk lubricant infusion in the soft substrate is a potential pathway for overcoming this limitation. We demonstrate that even 5% bulk lubricant infusion in PDMS reduces viscoelastic dissipation in the substrate by more than 30 times and more than doubles the droplet nucleation density. We correlate the droplet nucleation and growth rate with the material properties controlled by design, i.e. the fraction and composition of uncrosslinked chains, shear modulus, and viscoelastic dissipation. Through in-situ, microscale condensation on the substrates, we show that the increase in nucleation density and reduction in pre-coalescence droplet growth rate is insensitive to the percentage of lubricant in PDMS. Our results indicate the presence of a lubricant layer on the substrate surface that cloaks the growing condensate droplets. We visualize the cloaking effect and show that lubricant infusion in PDMS significantly increases the rate of cloaking compared to PDMS without any lubricant infusion. Finally, we show that the overall enhanced condensation due to bulk lubricant infusion in PDMS leads to more than 40% increase in dewing on the substrate.
△ Less
Submitted 26 August, 2021;
originally announced August 2021.
-
Ultra-Thin Lubricant-Infused Vertical Graphene Nanoscaffolds for High-Performance Dropwise Condensation
Authors:
Abinash Tripathy,
Cheuk Wing Edmond Lam,
Diana Davila,
Matteo Donati,
Athanasios Milionis,
Chander Shekhar Sharma,
Dimos Poulikakos
Abstract:
Lubricant-infused surfaces (LIS) are highly efficient in repelling water and constitute a very promising family of materials for condensation processes occurring in a broad range of energy applications. However, the performance of LIS in such processes is limited by the inherent thermal resistance imposed by the thickness of the lubricant and supporting surface structure, as well as by the gradual…
▽ More
Lubricant-infused surfaces (LIS) are highly efficient in repelling water and constitute a very promising family of materials for condensation processes occurring in a broad range of energy applications. However, the performance of LIS in such processes is limited by the inherent thermal resistance imposed by the thickness of the lubricant and supporting surface structure, as well as by the gradual depletion of the lubricant over time. Here we present a remarkable, ultra-thin (~70 nm) and conductive LIS architecture, obtained by infusing lubricant into a vertically grown graphene nanoscaffold on copper. The ultra-thin nature of the scaffold, combined with the high in-plane thermal conductivity of graphene, drastically minimize earlier limitations, effectively doubling the heat transfer performance compared to a state-of-the-art CuO LIS surface. We show that the effect of the thermal resistance to the heat transfer performance of a LIS surface, although often overlooked, can be so detrimental that a simple nanostructured CuO surface can outperform a CuO LIS surface, despite film condensation on the former. The present vertical graphene LIS is also found to be resistant to lubricant depletion, maintaining stable dropwise condensation for at least ~7 hours with no significant change of advancing contact angle and contact angle hysteresis. The lubricant consumed by the vertical graphene LIS is 52.6% less than the existing state-of-the-art CuO LIS, making also the fabrication process more economical.
△ Less
Submitted 7 April, 2021;
originally announced April 2021.
-
Sprayable Thin and Robust Carbon Nanofiber Composite Coating for Extreme Jum** Dropwise Condensation Performance
Authors:
Matteo Donati,
Cheuk Wing Edmond Lam,
Athanasios Milionis,
Chander Shekhar Sharma,
Abinash Tripathy,
Armend Zendeli,
Dimos Poulikakos
Abstract:
Condensation of water on metallic surfaces is critical for multiple energy conversion processes. Enhancement in condensation heat transfer efficiency often requires surface texturing and hydrophobicity, usually achieved through coatings, to maintain dropwise condensation. However, such surface treatments face conflicting challenges of minimal coating thermal resistance, enhanced coating durability…
▽ More
Condensation of water on metallic surfaces is critical for multiple energy conversion processes. Enhancement in condensation heat transfer efficiency often requires surface texturing and hydrophobicity, usually achieved through coatings, to maintain dropwise condensation. However, such surface treatments face conflicting challenges of minimal coating thermal resistance, enhanced coating durability and scalable fabrication. Here we present a thin (~ 2 μm) polytetrafluoroethylene - carbon nanofiber nanocomposite coating which meets these challenges and sustains coalescence-induced jum** droplet condensation for extended periods under highly demanding condensation conditions. Coating durability is achieved through improved substrate adhesion by depositing a sub-micron thick aluminum primer layer. Carbon nanofibers in a polytetrafluoroethylene matrix increase coating thermal conductivity and promote spontaneous surface nano-texturing to achieve superhydrophobicity for condensate microdroplets. The coating material can be deposited through direct spraying, ensuring economical scalability and versatility for a wide range of substrates. We know of no other coating for metallic surfaces that is able to sustain jum** dropwise condensation under shear of steam at 111 degC flowing at ~ 3 m s-1 over the surface for 10 hours and dropwise condensation for an additional 50 hours. Up to ~ 900% improvement in condensation heat transfer coefficient is achieved compared to conventional filmwise condensation.
△ Less
Submitted 5 October, 2020;
originally announced October 2020.
-
On the mechanism of hydrophilicity of graphene
Authors:
Guo Hong,
Yang Han,
Thomas M. Schutzius,
Yuming Wang,
Ying Pan,
Ming Hu,
Jiansheng Jie,
Chander S. Sharma,
Ulrich Müller,
Dimos Poulikakos
Abstract:
It is generally accepted that the hydrophilic property of graphene can be affected by the underlying substrate. However, the role of intrinsic vs. substrate contributions and the related mechanisms are vividly debated. Here we show that the intrinsic hydrophilicity of graphene can be intimately connected to the position of its Fermi level, which affects the interaction between graphene and water m…
▽ More
It is generally accepted that the hydrophilic property of graphene can be affected by the underlying substrate. However, the role of intrinsic vs. substrate contributions and the related mechanisms are vividly debated. Here we show that the intrinsic hydrophilicity of graphene can be intimately connected to the position of its Fermi level, which affects the interaction between graphene and water molecules. The underlying substrate, or dopants, can tune hydrophilicity by modulating the Fermi level of graphene. By shifting the Fermi level of graphene away from its Dirac point, via either chemical or electrical voltage do**, we show enhanced hydrophilicity with experiments and first principle simulations. Increased vapor condensation on graphene, induced by a simple shifting of its Fermi level, exemplifies applications in the area of interfacial transport phenomena.
△ Less
Submitted 23 August, 2016;
originally announced August 2016.
-
Micro-fabrication of Carbon Structures by Pattern Miniaturization in Resorcinol-Formaldehyde Gel
Authors:
Chandra S. Sharma,
Ankur Verma,
Manish M. Kulkarni,
Devendra K. Upadhyay,
Ashutosh Sharma
Abstract:
A simple and novel method to fabricate and miniaturize surface and sub-surface micro-structures and micro-patterns in glassy carbon is proposed and demonstrated. An aqueous resorcinol-formaldehyde (RF) sol is employed for micro-molding of the master-pattern to be replicated, followed by controlled drying and pyrolysis of the gel to reproduce an isotropically shrunk replica in carbon. The miniaturi…
▽ More
A simple and novel method to fabricate and miniaturize surface and sub-surface micro-structures and micro-patterns in glassy carbon is proposed and demonstrated. An aqueous resorcinol-formaldehyde (RF) sol is employed for micro-molding of the master-pattern to be replicated, followed by controlled drying and pyrolysis of the gel to reproduce an isotropically shrunk replica in carbon. The miniaturized version of the master-pattern thus replicated in carbon is about one order of magnitude smaller than original master by repeating three times the above cycle of molding and drying. The micro-fabrication method proposed will greatly enhance the toolbox for a facile fabrication of a variety of Carbon-MEMS and C-microfluidic devices.
△ Less
Submitted 20 September, 2010;
originally announced September 2010.
