-
Measurement of Volume Changes and Associated Stresses in Ge Electrodes Due to Na/Na$^+$ Redox Reactions
Authors:
Subhajit Rakshit,
Akshay S. Pakhare,
Olivia Ruiz,
M. Reza Khoshi,
Eric Detsi,
Huixin He,
Vijay A. Sethuraman,
Siva P. V. Nadimpalli
Abstract:
In situ electrochemical cells were assembled with an amorphous germanium (a-Ge) film as working electrode and sodium foil as reference and counter electrode. The stresses generated in a-Ge electrodes due to electrochemical reaction with sodium were measured in real-time during the galvanostatic cycling. A specially designed patterned a-Ge electrode was cycled against sodium and the corresponding v…
▽ More
In situ electrochemical cells were assembled with an amorphous germanium (a-Ge) film as working electrode and sodium foil as reference and counter electrode. The stresses generated in a-Ge electrodes due to electrochemical reaction with sodium were measured in real-time during the galvanostatic cycling. A specially designed patterned a-Ge electrode was cycled against sodium and the corresponding volume changes were measured using an AFM; it was observed that sodiation/desodiation of a-Ge results in more than 300% volume change, consistent with literature. The potential and stress response showed that the a-Ge film undergoes irreversible changes during the first sodiation process, but the subsequent desodiation/sodiation cycles are reversible. The stress response of the film reached steady-state after the initial sodiation and is qualitatively similar to the response of Ge during lithiation, i.e., initial linear elastic response followed by extensive plastic deformation of the film to accommodate large volume changes. However, despite being bigger ion, sodiation of Ge generated lower stress levels compared to lithiation. Consequently, the mechanical dissipation losses associated with plastic deformation are lower during sodiation process than it is for lithiation.
△ Less
Submitted 25 November, 2020;
originally announced December 2020.
-
In-situ Synthesis of Bismuth/Reduced Graphene Oxide Nanocomposites as High Capacity Anode Materials for Mg-ion Battery
Authors:
Tirupathi Rao Penki,
Geetha Valurouthu,
S. Shivakumara,
Vijay A. Sethuraman,
N. Munichandraiah
Abstract:
Herein, in-situ reduction of bismuth and graphene oxide was performed by a solvothermal method under a nitrogen atmosphere, and the resulting Bi on RGO nanocomposites were used as an anode material for Mg-ion batteries. The nanocomposite of 60% Bi:40% RGO is a beneficial anode material, delivering a discharge capacity as high as 413 and 372 mAh per g at the specific current of 39 mA per g in the 1…
▽ More
Herein, in-situ reduction of bismuth and graphene oxide was performed by a solvothermal method under a nitrogen atmosphere, and the resulting Bi on RGO nanocomposites were used as an anode material for Mg-ion batteries. The nanocomposite of 60% Bi:40% RGO is a beneficial anode material, delivering a discharge capacity as high as 413 and 372 mAh per g at the specific current of 39 mA per g in the 1st and 50th cycles, respectively. In addition, it shows high-rate capability with the discharge capacities of 381, 372, 354, 295, and 238 mAh per g at the specific currents of 53, 100, 200, 500, and 700 mA per g, respectively. The better electrochemical performance of the nanocomposite is due to improvement in the electronic conductivity and significant reduction of volume changes during electrochemical cycling. This study demonstrates the bismuth (Bi) on reduced graphene oxide (RGO) nanocomposite as a promising high-capacity anode for magnesium-ion batteries with longer life cycle and high-rate performance.
△ Less
Submitted 2 April, 2020;
originally announced April 2020.
-
Critical Evaluation of Relative Importance of Stress and Stress Gradient in Whisker Growth in Tin Coatings
Authors:
Piyush Jagtap,
Vijay A. Sethuraman,
Praveen Kumar
Abstract:
Here, we study the role of stress state and stress gradient in whisker growth in Sn coatings electrodeposited on brass. The bulk stress in Sn coatings was measured using a laser-optics based curvature setup, whereas glancing angle X-ray diffraction was employed to quantify the surface stress; this also allowed studying role of out-of-plane stress gradient in whisker growth. Both bulk stress and su…
▽ More
Here, we study the role of stress state and stress gradient in whisker growth in Sn coatings electrodeposited on brass. The bulk stress in Sn coatings was measured using a laser-optics based curvature setup, whereas glancing angle X-ray diffraction was employed to quantify the surface stress; this also allowed studying role of out-of-plane stress gradient in whisker growth. Both bulk stress and surface stress in Sn coating evolved with time, wherein both were compressive immediately after the deposition, and thereafter while the bulk stress monotonically became more compressive and subsequently saturated with aging at room temperature, the stress near the surface of the Sn coating continually became more tensile with aging. These opposing evolutionary behaviors of bulk and surface stresses readily established a negative out-of-plane stress gradient, required for spontaneous growth of whiskers. The importance of out-of-plane stress gradient was also validated by externally imposing widely different stress states and stress gradients in Sn coatings using a 3-point bending apparatus. It was consistently observed that whisker growth was more in the coatings under external tensile stress, however, with higher negative out-of-plane stress gradient. The results conclusively indicate the critical role of negative out-of-plane stress gradient on whisker growth, as compared to only the nature (i.e., sign and magnitude) of stress.
△ Less
Submitted 26 February, 2020;
originally announced March 2020.
-
The Influence of Elastic Strain on Catalytic Activity Towards the Hydrogen Evolution Reaction
Authors:
Kai Yan,
Tuhina Adit Maark,
Alireza Khorshidi,
Vijay A. Sethuraman,
Andrew Peterson,
Pradeep R. Guduru
Abstract:
Understanding the role of elastic strain in modifying catalytic reaction rates is crucial for catalyst design, but experimentally, this effect is often coupled with a ligand effect. To isolate the strain effect, we have investigated the influence of externally applied elastic strain on the catalytic activity of metal films towards the hydrogen evolution reaction (HER). We show that elastic strain…
▽ More
Understanding the role of elastic strain in modifying catalytic reaction rates is crucial for catalyst design, but experimentally, this effect is often coupled with a ligand effect. To isolate the strain effect, we have investigated the influence of externally applied elastic strain on the catalytic activity of metal films towards the hydrogen evolution reaction (HER). We show that elastic strain tunes the catalytic activity in a controlled and predictable way. Both theory and experiment show strain controls reactivity in a controlled manner consistent with the qualitative predictions of the HER volcano plot and the d-band theory: Ni and Pt activity were accelerated by compression, while Cu activity was accelerated by tension. By isolating the elastic strain effect from the ligand effect, this study provides a greater insight into the role of elastic strain in controlling electrocatalytic activity.
△ Less
Submitted 27 February, 2020;
originally announced March 2020.
-
Mathematical Model of a Direct Methanol Fuel Cell
Authors:
Brenda L. Garcia,
Vijay A. Sethuraman,
John W. Weidner,
Roger Dougal,
Ralph E. White
Abstract:
A one dimensional (1-D), isothermal model for a direct methanol fuel cell (DMFC) is presented. This model accounts for the kinetics of the multi-step methanol oxidation reaction at the anode. Diffusion and crossover of methanol are modeled and the mixed potential of the oxygen cathode due to methanol crossover is included. Kinetic and diffusional parameters are estimated by comparing the model to…
▽ More
A one dimensional (1-D), isothermal model for a direct methanol fuel cell (DMFC) is presented. This model accounts for the kinetics of the multi-step methanol oxidation reaction at the anode. Diffusion and crossover of methanol are modeled and the mixed potential of the oxygen cathode due to methanol crossover is included. Kinetic and diffusional parameters are estimated by comparing the model to data from a 25 cm2 DMFC. This semi-analytical model can be solved rapidly so that it is suitable for inclusion in real-time system level DMFC simulations.
△ Less
Submitted 27 February, 2020;
originally announced March 2020.
-
Effect of Di-phenyl Siloxane on the Catalytic Activity of Pt on Carbon
Authors:
Vijay A. Sethuraman,
John W. Weidner,
Lesia V. Protsailo
Abstract:
The effect of silicone on the catalytic activity of Pt for oxygen reduction and hydrogen adsorption was studied using di-phenyl siloxane as a source compound at a rotating disc electrode (RDE). Di-phenyl siloxane did not affect the catalytic activity of Pt when it was injected into the electrolyte. However, it blocked the oxygen reduction reaction when it was premixed with the catalyst. Proton tra…
▽ More
The effect of silicone on the catalytic activity of Pt for oxygen reduction and hydrogen adsorption was studied using di-phenyl siloxane as a source compound at a rotating disc electrode (RDE). Di-phenyl siloxane did not affect the catalytic activity of Pt when it was injected into the electrolyte. However, it blocked the oxygen reduction reaction when it was premixed with the catalyst. Proton transport was not blocked in either case. We postulate that di-phenyl siloxane induces hydrophobicity and causes local water starvation thereby blocking oxygen transport. Hence, the slow leaching of silicone seals in a fuel cell could cause silicon accumulation in the electrode, which will irreversibly degrade fuel cell performance by blocking oxygen transport to the catalyst sites.
△ Less
Submitted 26 February, 2020;
originally announced February 2020.
-
Hydrogen Peroxide Formation Rates in a PEMFC Anode and Cathode: Effect of Humidity and Temperature
Authors:
Vijay A. Sethuraman,
John W. Weidner,
Andrew T. Haug,
Sathya Motupally,
Lesia V. Protsailo
Abstract:
Hydrogen peroxide (H2O2) formation rates in a proton exchange membrane (PEM) fuel cell anode and cathode were estimated as a function of humidity and temperature by studying the oxygen reduction reaction (ORR) on a rotating ring disc electrode (RRDE). Fuel cell conditions were replicated by depositing a film of Pt/Vulcan XC-72 catalyst onto the disk and by varying the temperature, dissolved O2 con…
▽ More
Hydrogen peroxide (H2O2) formation rates in a proton exchange membrane (PEM) fuel cell anode and cathode were estimated as a function of humidity and temperature by studying the oxygen reduction reaction (ORR) on a rotating ring disc electrode (RRDE). Fuel cell conditions were replicated by depositing a film of Pt/Vulcan XC-72 catalyst onto the disk and by varying the temperature, dissolved O2 concentration and the acidity levels in hydrochloric acid (HClO4). The HClO4 acidity was correlated to ionomer water activity and hence fuel cell humidity. The H2O2 formation rates showed a linear dependence on oxygen concentration and square dependence on water activity. The H2O2 selectivity in ORR was independent of oxygen concentration but increased with decrease in water activity (i.e., decreased humidity). Potential dependent activation energy for the H2O2 formation reaction was estimated from data obtained at different temperatures.
△ Less
Submitted 20 February, 2020;
originally announced February 2020.
-
Investigation of Initial Lithiation of Silicon (100) Using Solid-State 7Li NMR
Authors:
Myeonghun Song,
Siva P. V. Nadimpalli,
Vijay A. Sethuraman,
Michael J. Chon,
Pradeep R. Guduru,
Li-Qiong Wang
Abstract:
Structural changes in amorphous LixSi during the initial lithiation of single crystal Si to amorphous LixSi were investigated as a function of Li flux and total charge using solid-state 7Li nuclear magnetic resonance (NMR) spectroscopy. Single crystal (100) Si wafers were used as a model system in this study, as the Li flux could be precisely controlled and uniformly distributed across the surface…
▽ More
Structural changes in amorphous LixSi during the initial lithiation of single crystal Si to amorphous LixSi were investigated as a function of Li flux and total charge using solid-state 7Li nuclear magnetic resonance (NMR) spectroscopy. Single crystal (100) Si wafers were used as a model system in this study, as the Li flux could be precisely controlled and uniformly distributed across the surface of the wafer. It was observed that peak shifts in solid-state 7Li NMR spectra varied as a function of the Li flux during the initial lithiation and stayed constant for samples of the same Li flux regardless of the total charge applied to the electrodes. We conclude from these results that the Li concentration in LixSi stays constant for a given flux regardless of the total coulombic charge applied to the electrode. The results from this study help better understand the kinetics, the reaction mechanisms, and the kinetic modeling of chemical reactions at the reaction front during the initial lithiation of Si (100).
△ Less
Submitted 8 November, 2015;
originally announced November 2015.
-
On the Role of Elastic Strain on Electrocatalysis of Oxygen Reduction Reaction on Pt
Authors:
Vijay A. Sethuraman,
Deepa Vairavapandian,
Manon C. Lafouresse,
Tuhina A. Maark,
Naba Karan,
Shouheng Sun,
Ugo Bertocci,
Andrew A. Peterson,
Gery R. Stafford,
Pradeep R. Guduru
Abstract:
The effect of elastic strain on catalytic activity of platinum (Pt) towards oxygen reduction reaction (ORR) is investigated through de-alloyed Pt-Cu thin films; stress evolution in the de-alloyed layer and the mass of the Cu removed are measured in real-time during electrochemical de-alloying of (111)-textured thin-film PtCu (1:1, atom %) electrodes. In situ stress measurements are made using the…
▽ More
The effect of elastic strain on catalytic activity of platinum (Pt) towards oxygen reduction reaction (ORR) is investigated through de-alloyed Pt-Cu thin films; stress evolution in the de-alloyed layer and the mass of the Cu removed are measured in real-time during electrochemical de-alloying of (111)-textured thin-film PtCu (1:1, atom %) electrodes. In situ stress measurements are made using the cantilever-deflection method and nano-gravimetric measurements are made using an electrochemical quartz crystal nanobalance. Upon de-alloying via successive voltammetric sweeps between -0.05 and 1.15 V vs. standard hydrogen electrode, compressive stress develops in the de-alloyed Pt layer at the surface of thin-film PtCu electrodes. The de-alloyed films also exhibit enhanced catalytic activity towards ORR compared to polycrystalline Pt. In situ nanogravimetric measurements reveal that the mass of de-alloyed Cu is approximately 210 +/- 46 ng/cm2, which corresponds to a de-alloyed layer thickness of 1.2 +/- 0.3 monolayers or 0.16 +/- 0.04 nm. The average biaxial stress in the de-alloyed layer is estimated to be 4.95 +/- 1.3 GPa, which corresponds to an elastic strain of 1.47 +/- 0.4%. In addition, density functional theory calculations have been carried out on biaxially strained Pt (111) surface to characterize the effect of strain on its ORR activity; the predicted shift in the limiting potentials due to elastic strain is found to be in good agreement with the experimental shift in the cyclic voltammograms for the dealloyed PtCu thin film electrodes.
△ Less
Submitted 8 November, 2015;
originally announced November 2015.
-
Stress Evolution in Lithium-ion Composite Electrodes during Electrochemical Cycling and Resulting Internal Pressures on the Cell Casing
Authors:
Siva P. V. Nadimpalli,
Vijay A. Sethuraman,
Daniel P. Abraham,
Allan F. Bower,
Pradeep R. Guduru
Abstract:
Composite cathode coatings made of a high energy density layered oxide (Li1.2Ni0.15Mn0.55Co0.1O2, theoretical capacity ~377 mAh/g), polyvinylidene fluoride (PVdF) binder, and electron-conduction additives, were bonded to an elastic substrate. An electrochemical cell, built by pairing the cathode with a capacity-matched graphite anode, was electrochemically cycled and the real-time average stress e…
▽ More
Composite cathode coatings made of a high energy density layered oxide (Li1.2Ni0.15Mn0.55Co0.1O2, theoretical capacity ~377 mAh/g), polyvinylidene fluoride (PVdF) binder, and electron-conduction additives, were bonded to an elastic substrate. An electrochemical cell, built by pairing the cathode with a capacity-matched graphite anode, was electrochemically cycled and the real-time average stress evolution in the cathode coating was measured using a substrate-curvature technique. Features in the stress evolution profile showed correlations with phase changes in the oxide, thus yielding data complementary to in situ XRD studies on this material. The stress evolution showed a complex variation with lithium concentration suggesting that the volume changes associated with phase transformations in the oxide are not monotonically varying functions of lithium concentration. The peak tensile stress in the cathode during oxide delithiation was approximately 1.5 MPa and the peak compressive stress during oxide lithiation was about 6 MPa. Stress evolution in the anode coating was also measured separately using the same technique. The measured stresses are used to estimate the internal pressures that develop in a cylindrical lithium-ion cell with jelly-roll electrodes.
△ Less
Submitted 8 November, 2015;
originally announced November 2015.
-
Real-time Stress Measurements in Germanium Thin Film Electrodes during Electrochemical Lithiation/delithiation Cycling
Authors:
Siva P. V. Nadimpalli,
Rajasekhar Tripuraneni,
Vijay A. Sethuraman
Abstract:
An in situ study of stress evolution and mechanical behavior of germanium as a lithium-ion battery electrode material is presented. Thin films of germanium are cycled in a half-cell configuration with lithium metal foil as counter/reference electrode, with 1M LiPF6 in ethylene carbonate, diethyl carbonate, dimethyl carbonate solution (1:1:1, wt. %) as electrolyte. Real-time stress evolution in the…
▽ More
An in situ study of stress evolution and mechanical behavior of germanium as a lithium-ion battery electrode material is presented. Thin films of germanium are cycled in a half-cell configuration with lithium metal foil as counter/reference electrode, with 1M LiPF6 in ethylene carbonate, diethyl carbonate, dimethyl carbonate solution (1:1:1, wt. %) as electrolyte. Real-time stress evolution in the germanium thin-film electrodes during electrochemical lithiation/delithiation is measured by monitoring the substrate curvature using the multi-beam optical sensing method. Upon lithiation a-Ge undergoes extensive plastic deformation, with a peak compressive stress reaching as high as -0.76 +/- 0.05 GPa (mean +/- standard deviation). The compressive stress decreases with lithium concentration reaching a value of approximately -0.3 GPa at the end of lithiation. Upon delithiation the stress quickly became tensile and follows a trend that mirrors the behavior on compressive side; the average peak tensile stress of the lithiated Ge samples was approximately 0.83 GPa. The peak tensile stress data along with the SEM analysis was used to estimate a lower bound fracture resistance of lithiated Ge, which is approximately 5.3 J/m^2. It was also observed that the lithiated Ge is rate sensitive, i.e., stress depends on how fast or slow the charging is carried out.
△ Less
Submitted 8 November, 2015;
originally announced November 2015.
-
Measurement and modeling of the mechanical and electrochemical response of amorphous Si thin film electrodes during cyclic lithiation
Authors:
Giovanna Bucci,
Siva P. V. Nadimpalli,
Vijay A. Sethuraman,
Allan F. Bower,
Pradeep R. Guduru
Abstract:
A combination of experimental measurements and numerical simulations are used to characterize the mechanical and electrochemical response of thin film amorphous Si electrodes during cyclic lithiation. Parameters extracted from the experiment include the variation of elastic modulus and the flow stress as functions of Li concentration; the strain rate sensitivity; the diffusion coefficient for Li t…
▽ More
A combination of experimental measurements and numerical simulations are used to characterize the mechanical and electrochemical response of thin film amorphous Si electrodes during cyclic lithiation. Parameters extracted from the experiment include the variation of elastic modulus and the flow stress as functions of Li concentration; the strain rate sensitivity; the diffusion coefficient for Li transport in the electrode; the free energy of mixing as a function of Li concentration in the electrode; the exchange current density for the Lithium insertion reaction; as well as reaction rates and diffusion coefficients characterizing the rate of formation of solid-electrolyte interphase layer at the electrode surface. Model predictions are compared with experimental measurements; and the implications for practical Si based electrodes are discussed.
△ Less
Submitted 22 November, 2013;
originally announced November 2013.
-
On plastic deformation and fracture in Si films during electrochemical lithiation/delithiation cycling
Authors:
Siva P. V. Nadimpalli,
Vijay A. Sethuraman,
Giovanna Bucci,
Venkat Srinivasan,
Allan F. Bower,
Pradeep R. Guduru
Abstract:
An in situ study of deformation, fracture, and fatigue behavior of silicon as a lithium-ion battery electrode material is presented. Thin films (100-200 nm) of silicon are cycled in a half-cell configuration with lithium metal foil as counter/reference electrode, with 1M lithium hexafluorophosphate in ethylene carbonate, diethylene carbonate, dimethyl carbonate solution (1:1:1, wt.%) as electrolyt…
▽ More
An in situ study of deformation, fracture, and fatigue behavior of silicon as a lithium-ion battery electrode material is presented. Thin films (100-200 nm) of silicon are cycled in a half-cell configuration with lithium metal foil as counter/reference electrode, with 1M lithium hexafluorophosphate in ethylene carbonate, diethylene carbonate, dimethyl carbonate solution (1:1:1, wt.%) as electrolyte. Stress evolution in the Si thin-film electrodes during electrochemical lithiation and delithiation is measured by monitoring the substrate curvature using the multi-beam optical sensing method. The stress measurements have been corrected for contributions from residual stress arising from sputter-deposition. An indirect method for estimating the potential errors due to formation of the solid-electrolyte-interphase layer and surface charge on the stress measurements was presented. The films undergo extensive inelastic deformation during lithiation and delithiation. The peak compressive stress during lithiation was 1.48 GPa. The stress data along with the electron microscopy observations are used to estimate an upper bound fracture resistance of lithiated Si, which is approximately 9-11 J/m^2. Fracture initiation and crack density evolution as a function of cycle number is also reported.
△ Less
Submitted 8 September, 2013;
originally announced September 2013.
-
Parameter Estimates for a Polymer Electrolyte Membrane Fuel Cell Cathode
Authors:
Qingzhi Guo,
Vijay A. Sethuraman,
Ralph E. White
Abstract:
Five parameters of a model of a polymer electrolyte membrane fuel cell cathode (the porosity of the gas diffusion layer, the porosity of the catalyst layer, the exchange current density of the oxygen reduction reaction, the effective ionic conductivity of the electrolyte, and the ratio of the effective diffusion coefficient of oxygen in a flooded spherical agglomerate particle to the squared parti…
▽ More
Five parameters of a model of a polymer electrolyte membrane fuel cell cathode (the porosity of the gas diffusion layer, the porosity of the catalyst layer, the exchange current density of the oxygen reduction reaction, the effective ionic conductivity of the electrolyte, and the ratio of the effective diffusion coefficient of oxygen in a flooded spherical agglomerate particle to the squared particle radius) were determined by the least square fitting of experimental polarization curves. The values of parameters obtained in this work indicate that ionic conduction and gas-phase transport are two processes significantly influencing the performance of PEMFC air cathodes. While ionic conduction influences cathode performance over a wide range of current densities, gas-phase transport influences cathode performance only at high current densities.
△ Less
Submitted 21 August, 2013;
originally announced August 2013.
-
Quantifying Oxidation Rates of Carbon Monoxide on a Pt/C Electrode
Authors:
Siva Balasubramanian,
Balasubramanian Lakshmanan,
Christine E. Hetzke,
Vijay A. Sethuraman,
John W. Weidner
Abstract:
The electrochemical oxidation of carbon monoxide adsorbed (COad) on platinum-on-carbon electrodes was studied via a methodology in which pre-adsorbed CO was partially oxidized by applying potentiostatic pulses for certain durations. The residual COad was analyzed using strip** voltammetry that involved the deconvolution of COad oxidation peaks of voltammograms to quantify the weakly and strongly…
▽ More
The electrochemical oxidation of carbon monoxide adsorbed (COad) on platinum-on-carbon electrodes was studied via a methodology in which pre-adsorbed CO was partially oxidized by applying potentiostatic pulses for certain durations. The residual COad was analyzed using strip** voltammetry that involved the deconvolution of COad oxidation peaks of voltammograms to quantify the weakly and strongly bound species of COad. The data obtained for various potentials and temperatures were fit to a model based on a nucleation and growth mechanism. The resulting fit produced potential- and temperature-dependent rate parameters that provided insight into the oxidation mechanism of the two COad species. Irrespective of the applied potential or temperature, the concentration of weakly bound COad species decreased exponentially with time. In contrast, the strongly bound COad species showed a gradual transition of mechanisms, from progressive nucleation at relatively low potentials to exponential decay at high potentials.
△ Less
Submitted 20 August, 2013;
originally announced August 2013.
-
Importance of Catalyst Stability vis-à-vis Hydrogen Peroxide Formation Rates in PEM Fuel Cell Electrodes
Authors:
Vijay A. Sethuraman,
John W. Weidner,
Andrew T. Haug,
Marianne Pemberton,
Lesia V. Protsailo
Abstract:
The role of catalyst stability on the adverse effects of hydrogen peroxide (H2O2) formation rates in a proton exchange membrane fuel cell (PEMFC) is investigated for Pt, Pt binary (PtX, X = Co, Ru, Rh, V, Ni) and ternary (PtCoX, X = Ir, Rh) catalysts. The selectivity of these catalysts towards H2O2 formation in the oxygen reduction reaction (ORR) was measured on a rotating ring disc electrode. The…
▽ More
The role of catalyst stability on the adverse effects of hydrogen peroxide (H2O2) formation rates in a proton exchange membrane fuel cell (PEMFC) is investigated for Pt, Pt binary (PtX, X = Co, Ru, Rh, V, Ni) and ternary (PtCoX, X = Ir, Rh) catalysts. The selectivity of these catalysts towards H2O2 formation in the oxygen reduction reaction (ORR) was measured on a rotating ring disc electrode. These measured values were used in conjunction with local oxygen and proton concentrations to estimate local H2O2 formation rates in a PEMFC anode and cathode. The effect of H2O2 formation rates on the most active and durable of these catalysts (PtCo and PtIrCo) on Nafion membrane durability was studied using a single-sided membrane electrode assembly (MEA) with a built-in reference electrode. Fluoride ion concentration in the effluent water was used as an indicator of the membrane degradation rate. PtIrCo had the least fluorine emission rate (FER) followed by PtCo/KB and Pt/KB. Though PtCo and PtIrCo show higher selectivity for H2O2 formation than unalloyed Pt, they did not contribute to membrane degradation. This result is explained in terms of catalyst stability as measured in potential cycling tests in liquid electrolyte as well as in a functional PEM fuel cell.
△ Less
Submitted 19 August, 2013;
originally announced August 2013.
-
Stress Evolution in Composite Silicon Electrodes during Lithiation/Delithiation
Authors:
Vijay A. Sethuraman,
Annam Nguyen,
Michael J. Chon,
Siva P. V. Nadimpalli,
Hailong Wang,
Daniel P. Abraham,
Allan F. Bower,
Vivek B. Shenoy,
Pradeep R. Guduru
Abstract:
We report real-time average stress measurements on composite silicon electrodes made with two different binders [Carboxymethyl cellulose (CMC), and polyvinylidene fluoride (PVDF)] during electrochemical lithiation and delithiation. During galvanostatic lithiation at very slow rates, the stress in a CMC-based electrode becomes compressive and increases to 70 MPa, where it reaches a plateau and incr…
▽ More
We report real-time average stress measurements on composite silicon electrodes made with two different binders [Carboxymethyl cellulose (CMC), and polyvinylidene fluoride (PVDF)] during electrochemical lithiation and delithiation. During galvanostatic lithiation at very slow rates, the stress in a CMC-based electrode becomes compressive and increases to 70 MPa, where it reaches a plateau and increases slowly thereafter with capacity. The PVDF-based electrode exhibits similar behavior, although with lower peak compressive stress of about 12 MPa. These initial experiments indicate that the stress evolution in a Si composite electrode depends strongly on the mechanical properties of the binder. Stress data obtained from a series of lithiation/delithiation cycles suggests plasticity induced irreversible shape changes in contacting Si particles, and as a result, the stress response of the system during any given lithiation/delithiation cycle depends on the cycling history of the electrode. While these results constitute the first in-situ stress measurements on composite Si electrodes during electrochemical cycling, the diagnostic technique described herein can be used to assess the mechanical response of a composite electrode made with other active material/binder combinations.
△ Less
Submitted 18 August, 2013;
originally announced August 2013.
-
Quantifying Capacity Loss due to Solid-Electrolyte-Interphase Layer Formation on Silicon Negative Electrodes in Lithium-ion Batteries
Authors:
Siva P. V. Nadimpalli,
Vijay A. Sethuraman,
Swapnil Dalavi,
Brett Lucht,
Michael J. Chon,
Vivek B. Shenoy,
Pradeep R. Guduru
Abstract:
Charge lost per unit surface area of a silicon electrode due to the formation of solid-electrolyte-interphase (SEI) layer during initial lithiation was quantified, and the species that constitute this layer were identified. Coin cells made with Si thin-film electrodes were subjected to a combination of galvanostatic and potentiostatic lithiation and delithiation cycles to accurately measure the ca…
▽ More
Charge lost per unit surface area of a silicon electrode due to the formation of solid-electrolyte-interphase (SEI) layer during initial lithiation was quantified, and the species that constitute this layer were identified. Coin cells made with Si thin-film electrodes were subjected to a combination of galvanostatic and potentiostatic lithiation and delithiation cycles to accurately measure the capacity lost to SEI-layer formation. While the planar geometry of amorphous thin films allows accurate calculation of surface area, creation of additional surface by cracking was prevented by minimizing the thickness of the Si film. The cycled electrodes were analyzed with X-ray photoelectron spectroscopy to characterize the composition of the SEI layer. The charge lost due to SEI formation measured from coin cell experiments was found to be in good agreement with the first-cycle capacity loss during the initial lithiation of a Si (100) crystal with planar geometry. The methodology presented in this work is expected to provide a useful practical tool for battery-material developers in estimating the expected capacity loss due to first cycle SEI-layer formation and in choosing an appropriate particle size distribution that balances mechanical integrity and the first cycle capacity loss in large volume expansion electrodes for lithium-ion batteries.
△ Less
Submitted 24 May, 2012;
originally announced May 2012.
-
Real-Time Stress Measurements in Lithium-ion Battery Negative-electrodes
Authors:
Vijay A. Sethuraman,
Nathan Van Winkle,
Daniel P. Abraham,
Allan F. Bower,
Pradeep R. Guduru
Abstract:
Real-time stress evolution in a graphite-based lithium-ion battery negative-electrode during electrolyte wetting and electrochemical cycling is measured through wafer-curvature method. Upon electrolyte addition, the composite electrode rapidly develops compressive stress of the order of 1-2 MPa due to binder swelling; upon continued exposure, the stress continues to evolve towards an apparent plat…
▽ More
Real-time stress evolution in a graphite-based lithium-ion battery negative-electrode during electrolyte wetting and electrochemical cycling is measured through wafer-curvature method. Upon electrolyte addition, the composite electrode rapidly develops compressive stress of the order of 1-2 MPa due to binder swelling; upon continued exposure, the stress continues to evolve towards an apparent plateau. During electrochemical intercalation at a slow rate, the compressive stress increases with the electrode's state-of-charge, reaching a maximum value of 10 - 12 MPa. There appears to be an approximate correlation between the rate of stress rise and the staging behavior of the lithiated graphite. De-intercalation at a slow rate results in a similar linear decrease in electrode stress. Tensile stress of a few MPa develops at the end of deintercalation in the first few cycles, after which the electrode remains under compressive stress only. Although higher peak stresses are seen at high C-rates, the dependence appears to be relatively weak (up to 5C). These measurements reveal, for the first time, the nature of stress evolution in practical lithium-ion-battery electrodes and provide useful data to quantify the driving force for mechanical damage that accrues in composite electrodes upon repeated cycling. While the reported results can serve as reference for calibrating theoretical and computational models to predict electrode stress and damage evolution, the methodology demonstrated can be used to measure stresses and characterize fatigue damage in any composite lithium-ion-battery electrode as well as optimize its microstructure to mitigate stress-related damage mechanisms.
△ Less
Submitted 10 January, 2012;
originally announced January 2012.
-
Capacity Fade due to Side-reactions in Silicon Anodes in Lithium-ion Batteries
Authors:
Vijay A. Sethuraman
Abstract:
It is shown that continuously occurring electrolyte-reduction reaction on freshly-exposed electrode surfaces during lithiation/delithiation cycles causes the lowering of cycling efficiency, and hence, capacity fade in well-cycled silicon anodes in lithium-ion batteries. Using galvanostatic lithiation/delithiation data from multiple cycles on a Li/Si half-cell, a methodology to separate the charge…
▽ More
It is shown that continuously occurring electrolyte-reduction reaction on freshly-exposed electrode surfaces during lithiation/delithiation cycles causes the lowering of cycling efficiency, and hence, capacity fade in well-cycled silicon anodes in lithium-ion batteries. Using galvanostatic lithiation/delithiation data from multiple cycles on a Li/Si half-cell, a methodology to separate the charge due to the main reaction (lithiation/delithiation of Si) from the side-reaction (electrolyte-reduction) is presented. The rate of this parasitic side reaction is estimated on well-cycled amorphous silicon thin-film electrodes at ambient temperature for the following three commonly-used lithium-ion electrolyte formulations: mixtures of ethylene carbonate and diethylene carbonate (EC:DEC) with and without a fluoroethylene carbonate (FEC) additive, and propylene carbonate (PC), all containing 1.2 M lithium hexafluorophosphate. Among the three formulations, the electrolyte containing EC:DEC with the FEC additive exhibits the lowest coulombic losses due to side-reactions, followed by PC, and EC:DEC without the FEC additive (i.e., EC:DEC + FEC > PC > EC:DEC). The importance of estimating side-reaction rates on a well-cycled electrode is discussed in the context of self-discharge, capacity fade, development of battery management system algorithms and precise mathematical modeling of lithium-ion batteries.
△ Less
Submitted 17 February, 2020; v1 submitted 6 January, 2012;
originally announced January 2012.
-
Analysis of Lithiation and Delithiation Kinetics in Silicon
Authors:
Vijay A. Sethuraman,
Venkat Srinivasan,
John Newman
Abstract:
Analysis of lithiation and delithiation kinetics in pulse-laser-deposited crystalline thin-film silicon (Si) electrodes is presented. Data from open-circuit relaxation experiments are used in conjunction with a model based on Tafel kinetics and double-layer capacitance to estimate the apparent transfer coefficients (αa, αc), and exchange current density to capacitance ratio (i0/Cdl) for lithiation…
▽ More
Analysis of lithiation and delithiation kinetics in pulse-laser-deposited crystalline thin-film silicon (Si) electrodes is presented. Data from open-circuit relaxation experiments are used in conjunction with a model based on Tafel kinetics and double-layer capacitance to estimate the apparent transfer coefficients (αa, αc), and exchange current density to capacitance ratio (i0/Cdl) for lithiation and delithiation reactions in a lithiated silicon (LixSi) system. Parameters estimated from data sets obtained during first-cycle amorphization of crystalline Si, as well as from cycled crystalline Si and amorphous Si thin-film electrodes do not show much variation, indicating that they are intrinsic to lithiation/delithiation in Si. A methodology to estimate the side-reaction rate and its role in the evolution of the open-circuit potential of the LixSi system are discussed. We conclude that the large potential offset between lithiation and delithiation reactions at any given state of charge is partially caused by a large kinetic resistance (i.e., small i0). Using the estimated parameters, the model is shown to predict successfully the behavior of the system under galvanostatic lithiation and delithiation.
△ Less
Submitted 6 January, 2012;
originally announced January 2012.
-
Measuring Oxygen, Carbon Monoxide and Hydrogen Sulfide Diffusion Coefficient and Solubility in Nafion Membranes
Authors:
Vijay A. Sethuraman,
Saahir Khan,
Jesse S. Jur,
Andrew T. Haug,
John W. Weidner
Abstract:
A Devanathan-Stachurski type diffusion cell made from a fuel cell assembly is designed to evaluate the gas transport properties of a proton exchange membrane as a function of cell temperature and gas pressure. Data obtained on this cell using the electrochemical monitoring technique (EMT) is used to estimate solubility and diffusion coefficient of oxygen (O2), carbon monoxide (CO) and hydrogen sul…
▽ More
A Devanathan-Stachurski type diffusion cell made from a fuel cell assembly is designed to evaluate the gas transport properties of a proton exchange membrane as a function of cell temperature and gas pressure. Data obtained on this cell using the electrochemical monitoring technique (EMT) is used to estimate solubility and diffusion coefficient of oxygen (O2), carbon monoxide (CO) and hydrogen sulfide (H2S) in Nafion membranes. Membrane swelling and reverse-gas diffusion due to water flux are accounted for in the parameter estimation procedure. Permeability of all three gases was found to increase with temperature. The estimated activation energies for O2, CO and H2S diffusion in Nafion 112 are 12.58, 20 and 8.85 kJ mol^-1, respectively. The estimated enthalpies of mixing for O2, CO and H2S in Nafion 112 are 5.88, 3.74 and 7.61 kJ mol^-1, respectively. An extensive comparison of transport properties estimated in this study to those reported in the literature suggests good agreement. Oxygen permeability in Nafion 117 was measured as a function of gas pressures between 1 and 3 atm. Oxygen diffusion coefficient in Nafion 117 is invariant with pressure and the solubility increases with pressure and obeys Henry's law. The estimated Henry's constant is 3.5 x 10^3 atm.
△ Less
Submitted 11 August, 2011;
originally announced August 2011.
-
Surface Structural Disordering in Graphite upon Lithium Intercalation/Deintercalation
Authors:
Vijay A. Sethuraman,
Laurence J. Hardwick,
Venkat Srinivasan,
Robert Kostecki
Abstract:
We report on the origin of the surface structural disordering in graphite anodes induced by lithium intercalation and deintercalation processes. Average Raman spectra of graphitic anodes reveal that cycling at potentials that correspond to low lithium concentrations in LixC (0 \leq x < 0.16) is responsible for most of the structural damage observed at the graphite surface. The extent of surface st…
▽ More
We report on the origin of the surface structural disordering in graphite anodes induced by lithium intercalation and deintercalation processes. Average Raman spectra of graphitic anodes reveal that cycling at potentials that correspond to low lithium concentrations in LixC (0 \leq x < 0.16) is responsible for most of the structural damage observed at the graphite surface. The extent of surface structural disorder in graphite is significantly reduced for the anodes that were cycled at potentials where stage-1 and stage-2 compounds (x > 0.33) are present. Electrochemical impedance spectra show larger interfacial impedance for the electrodes that were fully delithiated during cycling as compared to electrodes that were cycled at lower potentials (U < 0.15 V vs. Li/Li+). Steep Li+ surface-bulk concentration gradients at the surface of graphite during early stages of intercalation processes, and the inherent increase of the LixC d-spacing tend to induce local stresses at the edges of graphene layers, and lead to the breakage of C-C bonds. The exposed graphite edge sites react with the electrolyte to (re)form the SEI layer, which leads to gradual degradation of the graphite anode, and causes reversible capacity loss in a lithium-ion battery.
△ Less
Submitted 3 August, 2011;
originally announced August 2011.
-
In Situ Measurements of Stress Evolution in Silicon Thin Films During Electrochemical Lithiation and Delithiation
Authors:
Vijay A. Sethuraman,
Michael J. Chon,
Maxwell Shimshak,
Venkat Srinivasan,
Pradeep R. Guduru
Abstract:
We report in situ measurements of stress evolution in a silicon thin-film electrode during electrochemical lithiation and delithiation by using the Multi-beam Optical Sensor (MOS) technique. Upon lithiation, due to substrate constraint, the silicon electrode initially undergoes elastic deformation, resulting in rapid rise of compressive stress. The electrode begins to deform plastically at a compr…
▽ More
We report in situ measurements of stress evolution in a silicon thin-film electrode during electrochemical lithiation and delithiation by using the Multi-beam Optical Sensor (MOS) technique. Upon lithiation, due to substrate constraint, the silicon electrode initially undergoes elastic deformation, resulting in rapid rise of compressive stress. The electrode begins to deform plastically at a compressive stress of ca. -1.75 GPa; subsequent lithiation results in continued plastic strain, dissipating mechanical energy. Upon delithiation, the electrode first undergoes elastic straining in the opposite direction, leading to a tensile stress of ca. 1 GPa; subsequently, it deforms plastically during the rest of delithiation. The plastic flow stress evolves continuously with lithium concentration. Thus, mechanical energy is dissipated in plastic deformation during both lithiation and delithiation, and it can be calculated from the stress measurements; we show that it is comparable to the polarization loss. Upon current interrupt, both the film stress and the electrode potential relax with similar time-constants, suggesting that stress contributes significantly to the chemical potential of lithiated-silicon.
△ Less
Submitted 2 August, 2011;
originally announced August 2011.
-
Analysis of Sulfur Poisoning on a PEM Fuel Cell Electrode
Authors:
Vijay A. Sethuraman,
John W. Weidner
Abstract:
The extent of irreversible deactivation of Pt towards hydrogen oxidation reaction (HOR) due to sulfur adsorption and subsequent electrochemical oxidation is quantified in a functional PEM fuel cell. At 70 °C, sequential hydrogen sulfide (H2S) exposure and electrochemical oxidation experiments indicate that as much as 6% of total Pt sites are deactivated per monolayer sulfur adsorption at open circ…
▽ More
The extent of irreversible deactivation of Pt towards hydrogen oxidation reaction (HOR) due to sulfur adsorption and subsequent electrochemical oxidation is quantified in a functional PEM fuel cell. At 70 °C, sequential hydrogen sulfide (H2S) exposure and electrochemical oxidation experiments indicate that as much as 6% of total Pt sites are deactivated per monolayer sulfur adsorption at open circuit potential of a PEM fuel cell followed by its removal. The extent of such deactivation is much higher when the electrode is exposed to H2S when the fuel cell is operating at a finite load, and is dependent on the local overpotential and the duration of exposure. Regardless of this deactivation, the H2/O2 polarization curves obtained on post-recovery electrodes do not show performance losses suggesting that such performance curves alone cannot be used to assess the extent of recovery due to sulfur poisoning. A concise mechanism for the adsorption and electro-oxidation of H2S on Pt anode is presented. H2S dissociatively adsorbs onto Pt as two different sulfur species and at intermediate oxidation potentials, undergoes electro-oxidation to sulfur and then to sulfur dioxide (SO2). This mechanism is validated by charge balances between hydrogen desorption and sulfur electro-oxidation on Pt. The ignition potential for sulfur oxidation decreases with increase in temperature, which coupled with faster electro-oxidation kinetics result in the easier removal of adsorbed sulfur at higher temperatures. Furthermore, the adsorption potential is found to influence sulfur coverage of an electrode exposed to H2S. As an implication, the local potential of a PEM fuel cell anode exposed to H2S contaminated fuel should be kept below the equilibrium potential for sulfur oxidation to prevent irreversible loss of Pt sites.
△ Less
Submitted 2 August, 2011;
originally announced August 2011.
-
Lithium Diffusion in Graphitic Carbon
Authors:
Kristin Persson,
Vijay A. Sethuraman,
Laurence J. Hardwick,
Yoyo Hinuma,
Ying Shirley Meng,
Anton van der Ven,
Venkat Srinivasan,
Robert Kostecki,
Gerbrand Ceder
Abstract:
Graphitic carbon is currently considered the state-of-the-art material for the negative electrode in lithium-ion cells, mainly due to its high reversibility and low operating potential. However, carbon anodes exhibit mediocre charge/discharge rate performance, which contributes to severe transport-induced surface-structural damage upon prolonged cycling, and limits the lifetime of the cell. Lithiu…
▽ More
Graphitic carbon is currently considered the state-of-the-art material for the negative electrode in lithium-ion cells, mainly due to its high reversibility and low operating potential. However, carbon anodes exhibit mediocre charge/discharge rate performance, which contributes to severe transport-induced surface-structural damage upon prolonged cycling, and limits the lifetime of the cell. Lithium bulk diffusion in graphitic carbon is not yet completely understood, partly due to the complexity of measuring bulk transport properties in finite-sized, non-isotropic particles. To solve this problem for graphite, we use the Devanathan-Stachurski electrochemical methodology combined with ab-initio computations to deconvolute, and quantify the mechanism of lithium-ion diffusion in highly oriented pyrolytic graphite (HOPG). The results reveal inherent high lithium-ion diffusivity in the direction parallel to the graphene plane (ca. 10^-7 - 10^-6 cm2 s-1), as compared to sluggish lithium-ion transport along grain boundaries (ca. 10^-11 cm^2 s^-1), indicating the possibility of rational design of carbonaceous materials and composite electrodes with very high rate capability.
△ Less
Submitted 2 August, 2011;
originally announced August 2011.
-
In situ Measurement of Biaxial Modulus of Si Anode for Li-ion Batteries
Authors:
Vijay A. Sethuraman,
Michael J. Chon,
Maxwell Shimshak,
Nathan Van Winkle,
Pradeep R. Guduru
Abstract:
We report in situ measurement of biaxial moduli of a Si thin-film electrode as a function of its lithium concentration. During lithiation, biaxial compressive stress is induced in the Si film and it undergoes plastic flow. At any state-of-charge (SOC), a relatively small delithiation-relithiation sequence unloads and reloads the film elastically. From the stress and strain changes during a delithi…
▽ More
We report in situ measurement of biaxial moduli of a Si thin-film electrode as a function of its lithium concentration. During lithiation, biaxial compressive stress is induced in the Si film and it undergoes plastic flow. At any state-of-charge (SOC), a relatively small delithiation-relithiation sequence unloads and reloads the film elastically. From the stress and strain changes during a delithiation-relithiation cycle, the biaxial modulus of the film is calculated. Stress change is obtained by measuring the change in substrate curvature using a Multi-beam Optical Sensor; the elastic strain change is obtained from the change in SOC. By repeating these measurements at several different values of SOC, the biaxial modulus was seen to decrease from ca. 70 GPa for Li0.32Si to ca. 35 GPa for Li3.0Si. Such a significant reduction in elastic modulus has important implications for modeling stress evolution and mechanical degradation in Si-based anodes.
△ Less
Submitted 2 August, 2011;
originally announced August 2011.
-
In Situ Measurements of Stress-Potential Coupling in Lithiated Silicon
Authors:
Vijay A. Sethuraman,
Venkat Srinivasan,
Allan F. Bower,
Pradeep R. Guduru
Abstract:
An analysis of the dependence of electric potential on the state of stress of a lithiated-silicon electrode is presented. Based on the Larché and Cahn chemical potential for a solid solution, a thermodynamic argument is made for the existence of the stress-potential coupling in lithiated-silicon; based on the known properties of the material, the magnitude of the coupling is estimated to be ca. 60…
▽ More
An analysis of the dependence of electric potential on the state of stress of a lithiated-silicon electrode is presented. Based on the Larché and Cahn chemical potential for a solid solution, a thermodynamic argument is made for the existence of the stress-potential coupling in lithiated-silicon; based on the known properties of the material, the magnitude of the coupling is estimated to be ca. 60 mV/GPa in thin-film geometry. An experimental investigation is carried out on silicon thin-film electrodes in which the stress is measured in situ during electrochemical lithiation and delithiation. By progressively varying the stress through incremental delithiation, the relation between stress change and electric-potential change is measured to be 100 - 120 mV/GPa, which is of the same order of magnitude as the prediction of the analysis. The importance of the coupling is discussed in interpreting the hysteresis observed in potential vs. state-of-charge plots, and the role of stress in modifying the maximum charge capacity of a silicon electrode under stress.
△ Less
Submitted 1 August, 2011;
originally announced August 2011.
-
Increased Cycling Efficiency and Rate Capability of Copper-coated Silicon Anodes in Lithium-ion Batteries
Authors:
Vijay A. Sethuraman,
Kristin Kowolik,
Venkat Srinivasan
Abstract:
Cycling efficiency and rate capability of porous copper-coated, amorphous silicon thin-film negative electrodes are compared to equivalent silicon thin-film electrodes in lithium-ion batteries. The presence of a copper layer coated on the active material plays a beneficial role in increasing the cycling efficiency and the rate capability of silicon thin-film electrodes. Between 3C and C/8 discharg…
▽ More
Cycling efficiency and rate capability of porous copper-coated, amorphous silicon thin-film negative electrodes are compared to equivalent silicon thin-film electrodes in lithium-ion batteries. The presence of a copper layer coated on the active material plays a beneficial role in increasing the cycling efficiency and the rate capability of silicon thin-film electrodes. Between 3C and C/8 discharge rates, the available cell energy decreased by 8% and 18% for 40 nm copper-coated silicon and equivalent silicon thin-film electrodes, respectively. Copper-coated silicon thin-film electrodes also show higher cycling efficiency, resulting in lower capacity fade, than equivalent silicon thin-film electrodes. We believe that copper appears to act as a glue that binds the electrode together and prevents the electronic isolation of silicon particles, thereby decreasing capacity loss. Rate capability decreases significantly at higher copper-coating thicknesses as the silicon active-material is not accessed, suggesting that the thickness and porosity of the copper coating need to be optimized for enhanced capacity retention and rate capability in this system.
△ Less
Submitted 1 August, 2011;
originally announced August 2011.
-
A Finite Strain Model of Stress, Diffusion, Plastic Flow and Electrochemical Reactions in a Lithium-ion Half-cell
Authors:
Allan F. Bower,
Pradeep R. Guduru,
Vijay A. Sethuraman
Abstract:
We formulate the continuum field equations and constitutive equations that govern deformation, stress, and electric current flow in a Li-ion half-cell. The model considers mass transport through the system, deformation and stress in the anode and cathode, electrostatic fields, as well as the electrochemical reactions at the electrode/electrolyte interfaces. It extends existing analyses by accounti…
▽ More
We formulate the continuum field equations and constitutive equations that govern deformation, stress, and electric current flow in a Li-ion half-cell. The model considers mass transport through the system, deformation and stress in the anode and cathode, electrostatic fields, as well as the electrochemical reactions at the electrode/electrolyte interfaces. It extends existing analyses by accounting for the effects of finite strains and plastic flow in the electrodes, and by exploring in detail the role of stress in the electrochemical reactions at the electrode-electrolyte interfaces. In particular, we find that that stress directly influences the rest potential at the interface, so that a term involving stress must be added to the Nernst equation if the stress in the solid is significant. The model is used to predict the variation of stress and electric potential in a model 1-D half-cell, consisting of a thin film of Si on a rigid substrate, a fluid electrolyte layer, and a solid Li cathode. The predicted cycles of stress and potential are shown to be in good agreement with experimental observations.
△ Less
Submitted 29 July, 2011;
originally announced July 2011.
-
Real-time Measurement of Stress and Damage Evolution During Initial Lithiation of Crystalline Silicon
Authors:
Michael J. Chon,
Vijay A. Sethuraman,
Anthony McCormick,
Venkat Srinivasan,
Pradeep R. Guduru
Abstract:
Crystalline to amorphous phase transformation during initial lithiation in (100) silicon-wafers is studied in an electrochemical cell with lithium metal as the counter and reference electrode. It is demonstrated that severe stress jumps across the phase boundary lead to fracture and damage, which is an essential consideration in designing silicon based anodes for lithium ion batteries. During init…
▽ More
Crystalline to amorphous phase transformation during initial lithiation in (100) silicon-wafers is studied in an electrochemical cell with lithium metal as the counter and reference electrode. It is demonstrated that severe stress jumps across the phase boundary lead to fracture and damage, which is an essential consideration in designing silicon based anodes for lithium ion batteries. During initial lithiation, a moving phase boundary advances into the wafer starting from the surface facing the lithium electrode, transforming crystalline silicon into amorphous LixSi. The resulting biaxial compressive stress in the amorphous layer is measured in situ and it was observed to be ca. 0.5 GPa. HRTEM images reveal that the crystalline-amorphous phase boundary is very sharp, with a thickness of ~ 1 nm. Upon delithiation, the stress rapidly reverses, becomes tensile and the amorphous layer begins to deform plastically at around 0.5 GPa. With continued delithiation, the yield stress increases in magnitude, culminating in sudden fracture of the amorphous layer into micro-fragments and the cracks extend into the underlying crystalline silicon.
△ Less
Submitted 28 July, 2011;
originally announced July 2011.
