Showing 1–50 of 55 results for author: Seiden, A

Gain suppression study on LGADs at the CENPA tandem accelerator

Authors: S. Braun, Q. Buat, J. Ding, P. Kammel, S. M. Mazza, F. McKinney-Martinez, A. Molnar, C. Lansdell, J. Ott, A. Seiden, B. Schumm, Y. Zhao

Abstract: Low-Gain Avalanche Detectors (LGADs) are a type of thin silicon detector with a highly doped gain layer that provides moderate internal signal amplification. One recent challenge in the use of LGADs, studied by several research groups, is the gain suppression mechanism for large localized charge deposits. Using the CENPA Tandem accelerator at the University of Washington, the response of the LGADs… ▽ More Low-Gain Avalanche Detectors (LGADs) are a type of thin silicon detector with a highly doped gain layer that provides moderate internal signal amplification. One recent challenge in the use of LGADs, studied by several research groups, is the gain suppression mechanism for large localized charge deposits. Using the CENPA Tandem accelerator at the University of Washington, the response of the LGADs to MeV-range energy deposits from a proton beam was studied. Two LGAD prototypes and a PIN diode were characterized, and the gain of the devices was determined as a function of bias voltage, incidence beam angle and proton energy. This study was conducted in the scope of the PIONEER experiment, an experiment proposed at the Paul Scherrer Institute to perform high-precision measurements of rare pion decays. %At the center of the experiment, a high-granularity active target (ATAR) will stop the pion and characterize its decay. A range of deposited charge from Minimum Ionizing Particle (MIP, few 10s of KeV) from positrons to several MeV from the stop** pions/muons is expected in PIONEER; the detection and separation of close-by hits in such a wide dynamic range will be a main challenge of the experiment. To achieve this goal, the gain suppression mechanism has to be understood fully. △ Less

Submitted 3 May, 2024; originally announced May 2024.

Long-Distance Signal Propagation in AC-LGAD

Authors: Casey Bishop, Ayan Das, Jane Ding, Matthew Gignac, Forest Martinez-McKinney, Simone M. Mazza, Adam Molnar, Noah Nagel, Mohammad Nizam, Jennifer Ott, Hartmut F. -W. Sadrozinski, Bruce Schumm, Abraham Seiden, Taylor Shin, Andrew Summerell, Max Wilder, Yuzhan Zhao

Abstract: We investigate the signal propagation in AC-LGAD (aka RSD), which are LGAD with a common N+ layer and segmented AC-coupled readout contacts, by measuring response to IR laser TCT on a large selection of AC-LGAD with strip readout. The interest for this topic derives from the realization that while large charge sharing between neighboring strips is essential for good position resolution, large shar… ▽ More We investigate the signal propagation in AC-LGAD (aka RSD), which are LGAD with a common N+ layer and segmented AC-coupled readout contacts, by measuring response to IR laser TCT on a large selection of AC-LGAD with strip readout. The interest for this topic derives from the realization that while large charge sharing between neighboring strips is essential for good position resolution, large sharing beyond the next neighbor generates background signals which in general are detrimental to the sensor goal of low occupancy. Using AC-LGAD with strip readout produced by Hamamatsu Photonics (HPK), we evaluate the effects of a variety of sensor properties, including geometrical parameters (strip length, width), process parameters like the N+ layer resistivity, the coupling capacitance, and the thickness of the bulk on the signal sharing and the position resolution. △ Less

Submitted 22 May, 2024; v1 submitted 1 March, 2024; originally announced March 2024.

Comments: 9 pages, 7 figures, 13th Hiroshima Symposium HSTD13

First test beam measurement of the 4D resolution of an RSD 450 microns pitch pixel matrix connected to a FAST2 ASIC

Authors: L. Menzio, F. Siviero, R. Arcidiacono, N. Cartiglia, M. Costa, T. Croci, M. Ferrero, C. Hanna, L. Lanteri, S. Mazza, R. Mulargiaa, H-F W. Sadrozinski, A. Seiden, V. Sola, R. Whitea, M. Wilder

Abstract: This paper reports on the spatial and temporal resolutions of an RSD 450 microns pitch pixels array measured at the DESY test beam facility. RSDs, Resistive Silicon Detectors, also known as AC-LGAD, achieve excellent position and temporal resolution by exploiting charge sharing among neighboring electrodes. The RSD matrix used in this study is part of the second FBK RSD production, RSD2, and it is… ▽ More This paper reports on the spatial and temporal resolutions of an RSD 450 microns pitch pixels array measured at the DESY test beam facility. RSDs, Resistive Silicon Detectors, also known as AC-LGAD, achieve excellent position and temporal resolution by exploiting charge sharing among neighboring electrodes. The RSD matrix used in this study is part of the second FBK RSD production, RSD2, and it is composed of 450 microns pitch pixel with cross-shaped electrodes. A 7-pixel matrix was read out by the FAST2 ASIC, a 16-channel amplifier fully custom ASIC developed by INFN Torino using the 110 nm CMOS technology. The total area covered by the matrix is about 1.5 mm$^2$. The position resolution reached in this test is 15 microns, about 4\% of the pitch. The temporal resolution achieved in this work is 60 ps, dominated by the FAST2 resolution. The work also demonstrates that RSD sensors with cross-shaped electrodes achieve 100% fill factor and homogenous resolutions over the whole matrix surface, making them a suitable choice for 4D tracking applications. △ Less

Submitted 17 February, 2024; v1 submitted 2 February, 2024; originally announced February 2024.

Comments: 33 pages, 21 figures

Synchrotron light source X-ray detection with Low-Gain Avalanche Diodes

Authors: S. M. Mazza, G. Saito, Y. Zhao, T. Kirkes, N. Yoho, D. Yerdea, N. Nagel, J. Ott, M. Nizam, M. Leite, M. Moralles, H. F. -W. Sadrozinski, A. Seiden, B. Schumm, F. McKinney-Martinez, G. Giacomini, W. Chen

Abstract: The response of Low Gain Avalanche Diodes (LGADs), which are a type of thin silicon detector with internal gain, to X-rays of energies between 6-70 keV was characterized at the SLAC light source (SSRL). The utilized beamline at SSRL was 11-2, with a nominal beam size of 3 cm x 0.5 cm, a repetition rate of 500 MHz, and very monochromatic. LGADs of different thicknesses and gain layer configurations… ▽ More The response of Low Gain Avalanche Diodes (LGADs), which are a type of thin silicon detector with internal gain, to X-rays of energies between 6-70 keV was characterized at the SLAC light source (SSRL). The utilized beamline at SSRL was 11-2, with a nominal beam size of 3 cm x 0.5 cm, a repetition rate of 500 MHz, and very monochromatic. LGADs of different thicknesses and gain layer configurations were read out using fast amplification boards and digitized with a fast oscilloscope. Standard PiN devices were characterized as well. The devices' energy resolution and time resolution as a function of X-ray energy were measured. The charge collection and multiplication mechanism were simulated using TCAD Sentaurus, and the results were compared with the collected data. △ Less

Submitted 1 September, 2023; v1 submitted 27 June, 2023; originally announced June 2023.

Comments: 18 pages, 18 figures

TCAD simulation of AC-LGADs

Authors: M. Nizam, K. W. Shin, S. M. Mazza, J. Ott, A. Seiden, B. Schumm, Y. Zhao

Abstract: Low Gain Avalanche Detectors (LGADs) are thin silicon detectors with moderate internal signal amplification and time resolution as good as 17 ps for minimum ionizing particles. However, the current major limiting factor in granularity is due to protection structures preventing breakdown caused by high electric fields at the edge of the segmented implants. This structure, called Junction Terminatio… ▽ More Low Gain Avalanche Detectors (LGADs) are thin silicon detectors with moderate internal signal amplification and time resolution as good as 17 ps for minimum ionizing particles. However, the current major limiting factor in granularity is due to protection structures preventing breakdown caused by high electric fields at the edge of the segmented implants. This structure, called Junction Termination Extension (JTE), causes a region of 50-100~\um\ of inactive space. Therefore, the granularity of LGAD sensors is currently limited to the mm scale. A solution would be AC-coupled LGADs (AC-LGADs) which can provide spatial resolution on the 10's of um scale. This is achieved by an un-segmented (p-type) gain layer and (n-type) N-layer, and a dielectric layer separating the metal readout pads. The high spatial precision is achieved by using the information from multiple pads, exploiting the intrinsic charge-sharing capabilities of the AC-LGAD provided by the common N-layer. TCAD software (Silvaco and Sentaurus) was used to simulate the behavior of AC-LGADs. A set of simulated devices was prepared by changing several parameters in the sensor: N+ resistivity, strip length, and bulk thickness. △ Less

Submitted 24 May, 2023; originally announced May 2023.

High-Precision 4D Tracking with Large Pixels using Thin Resistive Silicon Detectors

Authors: R. Arcidiacono, G. Borghi, M. Boscardin, N. Cartiglia, M. Centis Vignali, M. Costa, G-F. Dalla Betta, M. Ferrero, F. Ficorella, G. Gioachin, L. Lanteri, M. Mandurrino, L. Menzio, R. Mulargia, L. Pancheri, G. Paternoster, A. Rojas, H-F W. Sadrozinski, A. Seiden, F. Siviero, V. Sola, M. Tornago

Abstract: The basic principle of operation of silicon sensors with resistive read-out is built-in charge sharing. Resistive Silicon Detectors (RSD, also known as AC-LGAD), exploiting the signals seen on the electrodes surrounding the impact point, achieve excellent space and time resolutions even with very large pixels. In this paper, a TCT system using a 1064 nm picosecond laser is used to characterize sen… ▽ More The basic principle of operation of silicon sensors with resistive read-out is built-in charge sharing. Resistive Silicon Detectors (RSD, also known as AC-LGAD), exploiting the signals seen on the electrodes surrounding the impact point, achieve excellent space and time resolutions even with very large pixels. In this paper, a TCT system using a 1064 nm picosecond laser is used to characterize sensors from the second RSD production at the Fondazione Bruno Kessler. The paper first introduces the parametrization of the errors in the determination of the position and time coordinates in RSD, then outlines the reconstruction method, and finally presents the results. Three different pixel sizes are used in the analysis: 200 x 340, 450 x 450, and 1300 x 1300 microns^2. At gain = 30, the 450 x 450 microns^2 pixel achieves a time jitter of 20 ps and a spatial resolution of 15 microns concurrently, while the 1300 x 1300 microns^2 pixel achieves 30 ps and 30 micron, respectively. The implementation of cross-shaped electrodes improves considerably the response uniformity over the pixel surface. △ Less

Submitted 24 November, 2022; originally announced November 2022.

Comments: 28 pages, 23 figures submitted to NIMA

First Test Results of the Trans-Impedance Amplifier Stage of the Ultra-fast HPSoC ASIC

Authors: C. Chock, K. Flood, L. Macchiarulo, I. Mostafanezhad, R. Perron, D. Uehara, F. Martinez-Mckinney, A. Martinez- Rojas, S. Mazza, M. Nizam, J. Ott, E. Ryan, H. F. -W. Sadrozinski, B. Schumm, A. Seiden, K. Shin, M. Tarka, M. Wilder, Y. Zhao

Abstract: We present the first results from the HPSoC ASIC designed for readout of Ultra-fast Silicon Detectors. The 4-channel ASIC manufactured in 65 nm CMOS by TSMC has been optimized for 50 um thick AC-LGAD. The evaluation of the analog front end with \b{eta}-particles im**ing on 3x3 AC-LGAD arrays (500 um pitch, 200x200 um2 metal) confirms a fast output rise time of 600 ps and good timing performance… ▽ More We present the first results from the HPSoC ASIC designed for readout of Ultra-fast Silicon Detectors. The 4-channel ASIC manufactured in 65 nm CMOS by TSMC has been optimized for 50 um thick AC-LGAD. The evaluation of the analog front end with \b{eta}-particles im**ing on 3x3 AC-LGAD arrays (500 um pitch, 200x200 um2 metal) confirms a fast output rise time of 600 ps and good timing performance with a jitter of 45 ps. Further calibration experiments and TCT laser studies indicate some gain limitations that are being investigated and are driving the design of the second-generation pre-amplification stages to reach a jitter of 15 ps. △ Less

Submitted 10 December, 2022; v1 submitted 17 October, 2022; originally announced October 2022.

Comments: 7 pages, 6 figures

Solid State Detectors and Tracking for Snowmass

Authors: A. Affolder, A. Apresyan, S. Worm, M. Albrow, D. Ally, D. Ambrose, E. Anderssen, N. Apadula, P. Asenov, W. Armstrong, M. Artuso, A. Barbier, P. Barletta, L. Bauerdick, D. Berry, M. Bomben, M. Boscardin, J. Brau, W. Brooks, M. Breidenbach, J. Buckley, V. Cairo, R. Caputo, L. Carpenter, M. Centis-Vignali , et al. (110 additional authors not shown)

Abstract: Tracking detectors are of vital importance for collider-based high energy physics (HEP) experiments. The primary purpose of tracking detectors is the precise reconstruction of charged particle trajectories and the reconstruction of secondary vertices. The performance requirements from the community posed by the future collider experiments require an evolution of tracking systems, necessitating the… ▽ More Tracking detectors are of vital importance for collider-based high energy physics (HEP) experiments. The primary purpose of tracking detectors is the precise reconstruction of charged particle trajectories and the reconstruction of secondary vertices. The performance requirements from the community posed by the future collider experiments require an evolution of tracking systems, necessitating the development of new techniques, materials and technologies in order to fully exploit their physics potential. In this article we summarize the discussions and conclusions of the 2022 Snowmass Instrumentation Frontier subgroup on Solid State and Tracking Detectors (Snowmass IF03). △ Less

Submitted 19 October, 2022; v1 submitted 8 September, 2022; originally announced September 2022.

Comments: for the Snowmass Instrumentation Frontier Solid State Detector and Tracking community

Electronics for Fast Timing

Authors: D. Braga, G. Carini, G. Deptuch, A. Dragone, F. Fahim, K. Flood, G. Giacomini, D. Gorni, R. Lipton, B. Markovic, S. Mazza, S. Miryala, P. Rubinov, G. Saffier-Ewing, H. Sadrozinski, A. Schwartzman, A. Seiden, Q. Sun, T. Zimmerman

Abstract: Picosecond-level timing will be an important component of the next generation of particle physics detectors. The ability to add a 4$^{th}$ dimension to our measurements will help address the increasing complexity of events at hadron colliders and provide new tools for precise tracking and calorimetry for all experiments. Detectors are described in detail on other whitepapers. In this note, we addr… ▽ More Picosecond-level timing will be an important component of the next generation of particle physics detectors. The ability to add a 4$^{th}$ dimension to our measurements will help address the increasing complexity of events at hadron colliders and provide new tools for precise tracking and calorimetry for all experiments. Detectors are described in detail on other whitepapers. In this note, we address challenges in electronics design for the new generations of fast timing detectors △ Less

Submitted 31 March, 2022; originally announced April 2022.

Comments: Submitted to the Proceedings of the US Community Study on the Future of Particle Physics (Snowmass 2021)

Testing Lepton Flavor Universality and CKM Unitarity with Rare Pion Decays in the PIONEER experiment

Authors: PIONEER Collaboration, W. Altmannshofer, H. Binney, E. Blucher, D. Bryman, L. Caminada, S. Chen, V. Cirigliano, S. Corrodi, A. Crivellin, S. Cuen-Rochin, A. Di Canto, L. Doria, A. Gaponenko, A. Garcia, L. Gibbons, C. Glaser, M. Escobar Godoy, D. Göldi, S. Gori, T. Gorringe, D. Hertzog, Z. Hodge, M. Hoferichter, S. Ito , et al. (36 additional authors not shown)

Abstract: The physics motivation and the conceptual design of the PIONEER experiment, a next-generation rare pion decay experiment testing lepton flavor universality and CKM unitarity, are described. Phase I of the PIONEER experiment, which was proposed and approved at Paul Scherrer Institut, aims at measuring the charged-pion branching ratio to electrons vs.\ muons, $R_{e/μ}$, 15 times more precisely than… ▽ More The physics motivation and the conceptual design of the PIONEER experiment, a next-generation rare pion decay experiment testing lepton flavor universality and CKM unitarity, are described. Phase I of the PIONEER experiment, which was proposed and approved at Paul Scherrer Institut, aims at measuring the charged-pion branching ratio to electrons vs.\ muons, $R_{e/μ}$, 15 times more precisely than the current experimental result, reaching the precision of the Standard Model (SM) prediction at 1 part in $10^4$. Considering several inconsistencies between the SM predictions and data pointing towards the potential violation of lepton flavor universality, the PIONEER experiment will probe non-SM explanations of these anomalies through sensitivity to quantum effects of new particles up to the PeV mass scale. The later phases of the PIONEER experiment aim at improving the experimental precision of the branching ratio of pion beta decay (BRPB), $π^+\to π^0 e^+ ν(γ)$, currently at $1.036(6)\times10^{-8}$, by a factor of three (Phase II) and an order of magnitude (Phase III). Such precise measurements of BRPB will allow for tests of CKM unitarity in light of the Cabibbo Angle Anomaly and the theoretically cleanest extraction of $|V_{ud}|$ at the 0.02\% level, comparable to the deduction from superallowed beta decays. △ Less

Submitted 10 March, 2022; originally announced March 2022.

Comments: contribution to Snowmass 2021 based on the PIONEER proposal (arXiv:2203.01981)

PIONEER: Studies of Rare Pion Decays

Authors: PIONEER Collaboration, W. Altmannshofer, H. Binney, E. Blucher, D. Bryman, L. Caminada, S. Chen, V. Cirigliano, S. Corrodi, A. Crivellin, S. Cuen-Rochin, A. DiCanto, L. Doria, A. Gaponenko, A. Garcia, L. Gibbons, C. Glaser, M. Escobar Godoy, D. Göldi, S. Gori, T. Gorringe, D. Hertzog, Z. Hodge, M. Hoferichter, S. Ito , et al. (36 additional authors not shown)

Abstract: A next-generation rare pion decay experiment, PIONEER, is strongly motivated by several inconsistencies between Standard Model (SM) predictions and data pointing towards the potential violation of lepton flavor universality. It will probe non-SM explanations of these anomalies through sensitivity to quantum effects of new particles even if their masses are at very high scales. Measurement of the c… ▽ More A next-generation rare pion decay experiment, PIONEER, is strongly motivated by several inconsistencies between Standard Model (SM) predictions and data pointing towards the potential violation of lepton flavor universality. It will probe non-SM explanations of these anomalies through sensitivity to quantum effects of new particles even if their masses are at very high scales. Measurement of the charged-pion branching ratio to electrons vs. muons $R_{e/μ}$ is extremely sensitive to new physics effects. At present, the SM prediction for $R_{e/μ}$ is known to 1 part in $10^4$, which is 15 times more precise than the current experimental result. An experiment reaching the theoretical accuracy will test lepton flavor universality at an unprecedented level, probing mass scales up to the PeV range. Measurement of pion beta decay, $π^+\to π^0 e^+ ν(γ)$, with 3 to 10-fold improvement in sensitivity, will determine $V_{ud}$ in a theoretically pristine manner and test CKM unitarity, which is very important in light of the recently emerged tensions. In addition, various exotic rare decays involving sterile neutrinos and axions will be searched for with unprecedented sensitivity. The experiment design benefits from experience with the recent PIENU and PEN experiments at TRIUMF and the Paul Scherrer Institut (PSI). Excellent energy and time resolutions, greatly increased calorimeter depth, high-speed detector and electronics response, large solid angle coverage, and complete event reconstruction are all critical aspects of the approach. The PIONEER experiment design includes a 3$π$ sr 25 radiation length calorimeter, a segmented low gain avalanche detector stop** target, a positron tracker, and other detectors. Using intense pion beams, and state-of-the-art instrumentation and computational resources, the experiments can be performed at the PSI ring cyclotron. △ Less

Submitted 7 March, 2022; v1 submitted 3 March, 2022; originally announced March 2022.

Tuning of gain layer do** concentration and Carbon implantation effect on deep gain layer

Authors: S. M. Mazza, C. Gee, Y. Zhao, R. Padilla, E. Ryan, N. Tournebise, B. Darby, F. McKinney-Martinez, H. F. -W. Sadrozinski, A. Seiden, B. Schumm, V. Cindro, G. Kramberger, I. Mandić, M. Mikuž, M. Zavrtanik, R. Arcidiacono, N. Cartiglia, M. Ferrero, M. Mandurrino, V. Sola, A. Staiano, M. Boscardin, G. F. Della Betta, F. Ficorella , et al. (2 additional authors not shown)

Abstract: Next generation Low Gain Avalanche Diodes (LGAD) produced by Hamamatsu photonics (HPK) and Fondazione Bruno Kessler (FBK) were tested before and after irradiation with ~1MeV neutrons at the JSI facility in Ljubljana. Sensors were irradiated to a maximum 1-MeV equivalent fluence of 2.5E15 Neq/cm2. The sensors analysed in this paper are an improvement after the lessons learned from previous FBK and… ▽ More Next generation Low Gain Avalanche Diodes (LGAD) produced by Hamamatsu photonics (HPK) and Fondazione Bruno Kessler (FBK) were tested before and after irradiation with ~1MeV neutrons at the JSI facility in Ljubljana. Sensors were irradiated to a maximum 1-MeV equivalent fluence of 2.5E15 Neq/cm2. The sensors analysed in this paper are an improvement after the lessons learned from previous FBK and HPK productions that were already reported in precedent papers. The gain layer of HPK sensors was fine-tuned to optimize the performance before and after irradiation. FBK sensors instead combined the benefit of Carbon infusion and deep gain layer to further the radiation hardness of the sensors and reduced the bulk thickness to enhance the timing resolution. The sensor performance was measured in charge collection studies using \b{eta}-particles from a 90Sr source and in capacitance-voltage scans (C-V) to determine the bias to deplete the gain layer. The collected charge and the timing resolution were measured as a function of bias voltage at -30C. Finally a correlation is shown between the bias voltage to deplete the gain layer and the bias voltage needed to reach a certain amount of gain in the sensor. HPK sensors showed a better performance before irradiation while maintaining the radiation hardness of the previous production. FBK sensors showed exceptional radiation hardness allowing a collected charge up to 10 fC and a time resolution of 40 ps at the maximum fluence. △ Less

Submitted 31 January, 2022; v1 submitted 21 January, 2022; originally announced January 2022.

Comments: arXiv admin note: text overlap with arXiv:2004.05260

Optimization of the Gain Layer Design of Ultra-Fast Silicon Detectors

Authors: Federico Siviero, Roberta Arcidiacono, Giacomo Borghi, Maurizio Boscardin, Nicolo Cartiglia, Matteo Centis Vignali, Marco Costa, Gian Franco Dalla Betta, Marco Ferrero, Francesco Ficorella, Giulia Gioachin, Marco Mandurrino, Simone Mazza, Luca Menzio, Lucio Pancheri, Giovanni Paternoster, Hartmut F. W. Sadrozinski, Abraham Seiden, Valentina Sola, Marta Tornago

Abstract: In the past few years, the need of measuring accurately the spatial and temporal coordinates of the particles generated in high-energy physics experiments has spurred a strong R\&D in the field of silicon sensors. Within these research activities, the so-called Ultra-Fast Silicon Detectors (UFSDs), silicon sensors optimized for timing based on the Low-Gain Avalanche Diode (LGAD) design, have been… ▽ More In the past few years, the need of measuring accurately the spatial and temporal coordinates of the particles generated in high-energy physics experiments has spurred a strong R\&D in the field of silicon sensors. Within these research activities, the so-called Ultra-Fast Silicon Detectors (UFSDs), silicon sensors optimized for timing based on the Low-Gain Avalanche Diode (LGAD) design, have been proposed and adopted by the CMS and ATLAS collaborations for their respective timing layers. The defining feature of the Ultra-Fast Silicon Detectors (UFSDs) is the internal multiplication mechanism, determined by the gain layer design. In this paper, the performances of several types of gain layers, measured with a telescope instrumented with a $^{90}$Sr $β$-source, are reported and compared. The measured sensors are produced by Fondazione Bruno Kessler (FBK) and Hamamatsu Photonics (HPK). The sensor yielding the best performance, both when new and irradiated, is an FBK 45\mum-thick sensor with a carbonated deep gain implant, where the carbon and the boron implants are annealed concurrently with a low thermal load. This sensor is able to achieve a time resolution of 40~ps up to a radiation fluence of~\fluence{2.5}{15}, delivering at least 5~fC of charge. △ Less

Submitted 8 March, 2022; v1 submitted 1 December, 2021; originally announced December 2021.

Comments: v3 revised version as requested by Editor

Inter-pad dead regions of irradiated FBK Low Gain Avalanche Detectors

Authors: B. Darby, S. M. Mazza, F. McKinney-Martinez, R. Padilla, H. F. -W. Sadrozinski, A. Seiden, B. Schumm, M. Wilder, Y. Zhao, R. Arcidiacono, N. Cartiglia, M. Ferrero, M. Mandurrino, V. Sola, A. Staiano, V. Cindro, G. Kranberger, I. Mandiz, M. Mikuz, M. Zavtranik, M. Boscardin, G. F. Della Betta, F. Ficorella, L. Pancheri, G. Paternoster

Abstract: Low Gain Avalanche Detectors (LGADs) are a type of thin silicon detector with a highly doped gain layer. LGADs manufactured by Fondazione Bruno Kessler (FBK) were tested before and after irradiation with neutrons. In this study, the Inter-pad distances (IPDs), defined as the width of the distances between pads, were measured with a TCT laser system. The response of the laser was tuned using $β$-pa… ▽ More Low Gain Avalanche Detectors (LGADs) are a type of thin silicon detector with a highly doped gain layer. LGADs manufactured by Fondazione Bruno Kessler (FBK) were tested before and after irradiation with neutrons. In this study, the Inter-pad distances (IPDs), defined as the width of the distances between pads, were measured with a TCT laser system. The response of the laser was tuned using $β$-particles from a 90Sr source. These insensitive "dead zones" are created by a protection structure to avoid breakdown, the Junction Termination Extension (JTE), which separates the pads. The effect of neutron radiation damage at \fluence{1.5}{15}, and \fluence{2.5}{15} on IPDs was studied. These distances are compared to the nominal distances given from the vendor, it was found that the higher fluence corresponds to a better matching of the nominal IPD. △ Less

Submitted 19 September, 2022; v1 submitted 24 November, 2021; originally announced November 2021.

A new approach to achieving high granularity for silicon diode detectors with impact ionization gain

Authors: S. Ayyoub, C. Gee, R. Islam, S. M. Mazza, B. Schumm, A. Seiden, Y. Zhao

Abstract: Low Gain Avalanche Diodes (LGADs) are thin (20-50 $μm$)silicon di ode sensors with modest internal gain (typically 5 to 50) and exceptional time resolution (17 $ps$ to 50 $ps$). However, the granularity of such devices is limited to the millimeter scale due to the need to include protection structures at the boundaries of the readout pads to avoid premature breakdown due to large local electric fi… ▽ More Low Gain Avalanche Diodes (LGADs) are thin (20-50 $μm$)silicon di ode sensors with modest internal gain (typically 5 to 50) and exceptional time resolution (17 $ps$ to 50 $ps$). However, the granularity of such devices is limited to the millimeter scale due to the need to include protection structures at the boundaries of the readout pads to avoid premature breakdown due to large local electric fields. In this paper we present a new approach -- the Deep-Junction LGAD (DJ-LGAD) -- that decouples the high-field gain region from the readout plane. This approach is expected to improve the achievable LGAD granularity to the tens-of-micron scale while maintaining direct charge collection on the segmented electrodes. △ Less

Submitted 2 January, 2021; originally announced January 2021.

Comments: 16 pages, 12 figures

Picosecond Timing Resolution Measurements of Low Gain Avalanche Detectors with a 120 GeV Proton Beam for the TOPSiDE Detector Concept

Authors: M. Jadhav, W. Armstrong, I. Cloet, S. Joosten, S. M. Mazza, J. Metcalfe, Z. -E. Meziani, H. F. -W. Sadrozinski, B. Schumm, A. Seiden

Abstract: This paper presents results that take a critical step toward proving 10 ps timing resolution's feasibility for particle identification in the TOPSiDE detector concept for the Electron-Ion Collider. Measurements of LGADs with a thickness of 35 micro-m and 50 micro-m are evaluated with a 120 GeV proton beam. The performance of the gain and timing response is assessed, including the dependence on the… ▽ More This paper presents results that take a critical step toward proving 10 ps timing resolution's feasibility for particle identification in the TOPSiDE detector concept for the Electron-Ion Collider. Measurements of LGADs with a thickness of 35 micro-m and 50 micro-m are evaluated with a 120 GeV proton beam. The performance of the gain and timing response is assessed, including the dependence on the reverse bias voltage and operating temperature. The best timing resolution of UFSDs in a test beam to date is achieved using three combined planes of 35 micro-m thick LGADs at -30 degree celsius with a precision of 14.3 ps (uncertainty 1.5 ps). △ Less

Submitted 19 February, 2021; v1 submitted 6 October, 2020; originally announced October 2020.

Comments: 18 pages, 16 figures, 3 tables

The ABC130 barrel module prototy** programme for the ATLAS strip tracker

Authors: Luise Poley, Craig Sawyer, Sagar Addepalli, Anthony Affolder, Bruno Allongue, Phil Allport, Eric Anderssen, Francis Anghinolfi, Jean-François Arguin, Jan-Hendrik Arling, Olivier Arnaez, Nedaa Alexandra Asbah, Joe Ashby, Eleni Myrto Asimakopoulou, Naim Bora Atlay, Ludwig Bartsch, Matthew J. Basso, James Beacham, Scott L. Beaupré, Graham Beck, Carl Beichert, Laura Bergsten, Jose Bernabeu, Prajita Bhattarai, Ingo Bloch , et al. (224 additional authors not shown)

Abstract: For the Phase-II Upgrade of the ATLAS Detector, its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100 % silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000… ▽ More For the Phase-II Upgrade of the ATLAS Detector, its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100 % silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototy** programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-25) and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototy** program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests. △ Less

Submitted 7 September, 2020; originally announced September 2020.

Comments: 82 pages, 66 figures

Journal ref: published 3 September 2020, Journal of Instrumentation, Volume 15, September 2020

Resistive AC-Coupled Silicon Detectors: principles of operation and first results from a combined analysis of beam test and laser data

Authors: M. Tornago, R. Arcidiacono, N. Cartiglia, M. Costa, M. Ferrero, M. Mandurrino, F. Siviero, V. Sola, A. Staiano, A. Apresyan, K. Di Petrillo, R. Heller, S. Los, G. Borghi, M. Boscardin, G-F Dalla Betta, F. Ficorella, L. Pancheri, G. Paternoster, H. Sadrozinski, A. Seiden

Abstract: This paper presents the principles of operation of Resistive AC-Coupled Silicon Detectors (RSDs) and measurements of the temporal and spatial resolutions using a combined analysis of laser and beam test data. RSDs are a new type of n-in-p silicon sensor based on the Low-Gain Avalanche Diode (LGAD) technology, where the $n^+$ implant has been designed to be resistive, and the read-out is obtained v… ▽ More This paper presents the principles of operation of Resistive AC-Coupled Silicon Detectors (RSDs) and measurements of the temporal and spatial resolutions using a combined analysis of laser and beam test data. RSDs are a new type of n-in-p silicon sensor based on the Low-Gain Avalanche Diode (LGAD) technology, where the $n^+$ implant has been designed to be resistive, and the read-out is obtained via AC-coupling. The truly innovative feature of RSD is that the signal generated by an im**ing particle is shared isotropically among multiple read-out pads without the need for floating electrodes or an external magnetic field. Careful tuning of the coupling oxide thickness and the $n^+$ do** profile is at the basis of the successful functioning of this device. Several RSD matrices with different pad width-pitch geometries have been extensively tested with a laser setup in the Laboratory for Innovative Silicon Sensors in Torino, while a smaller set of devices have been tested at the Fermilab Test Beam Facility with a 120 GeV/c proton beam. The measured spatial resolution ranges between $2.5\; μm$ for 70-100 pad-pitch geometry and $17\; μm$ with 200-500 matrices, a factor of 10 better than what is achievable in binary read-out ($bin\; size/ \sqrt{12}$). Beam test data show a temporal resolution of $\sim 40\; ps$ for 200-$μm$ pitch devices, in line with the best performances of LGAD sensors at the same gain. △ Less

Submitted 11 February, 2021; v1 submitted 18 July, 2020; originally announced July 2020.

Comments: 34 pages, 33 figures

Potential for Improved Time Resolution Using Very Thin Ultra-Fast Silicon Detectors (UFSDs)

Authors: A. Seiden, H. Ren, Y. **, S. Christie, Z. Galloway, C. Gee, C. Labitan, M. Lockerby, F. Martinez-McKinney, S. M. Mazza, R. Padilla, H. F. -W. Sadrozinski, B. Schumm, M. Wilder, W. Wyatt, Y. Zhao, N. Cartiglia

Abstract: Ultra-Fast Silicon Detectors (UFSDs) are n-in-p silicon detectors that implement moderate gain (typically 5 to 25) using a thin highly doped p++ layer between the high resistivity p-bulk and the junction of the sensor. The presence of gain allows excellent time measurement for im**ing minimum ionizing charged particles. An important design consideration is the sensor thickness, which has a stron… ▽ More Ultra-Fast Silicon Detectors (UFSDs) are n-in-p silicon detectors that implement moderate gain (typically 5 to 25) using a thin highly doped p++ layer between the high resistivity p-bulk and the junction of the sensor. The presence of gain allows excellent time measurement for im**ing minimum ionizing charged particles. An important design consideration is the sensor thickness, which has a strong impact on the achievable time resolution. We present the result of measurements for LGADs of thickness between 20 micro-m and 50 micro-m. The data are fit to a formula that captures the impact of both electronic jitter and Landau fluctuations on the time resolution. The data illustrate the importance of having a saturated electron drift velocity and a large signal-to-noise in order to achieve good time resolution. Sensors of 20 micro-m thickness offer the potential of 10 to 15 ps time resolution per measurement, a significant improvement over the value for the 50 micro-m sensors that have been typically used to date. △ Less

Submitted 24 February, 2021; v1 submitted 7 June, 2020; originally announced June 2020.

Comments: 14 pages, 11 figures, 2 tables

Radiation Campaign of HPK Prototype LGAD sensors for the High-Granularity Timing Detector (HGTD)

Authors: X. Shi, M. K. Ayoub, J. Barreiro Guimarães da Costa, H. Cui, R. Kiuchi, Y. Fan, S. Han, Y. Huang, M. **g, Z. Liang, B. Liu, J. Liu, F. Lyu, B. Qi, K. Ran, L. Shan, L. Shi, Y. Tan, K. Wu, S. Xiao, T. Yang, Y. Yang, C. Yu, M. Zhao, X. Zhuang , et al. (52 additional authors not shown)

Abstract: We report on the results of a radiation campaign with neutrons and protons of Low Gain Avalanche Detectors (LGAD) produced by Hamamatsu (HPK) as prototypes for the High-Granularity Timing Detector (HGTD) in ATLAS. Sensors with an active thickness of 50~$μ$m were irradiated in steps of roughly 2$\times$ up to a fluence of $3\times10^{15}~\mathrm{n_{eq}cm^{-2}}$. As a function of the fluence, the co… ▽ More We report on the results of a radiation campaign with neutrons and protons of Low Gain Avalanche Detectors (LGAD) produced by Hamamatsu (HPK) as prototypes for the High-Granularity Timing Detector (HGTD) in ATLAS. Sensors with an active thickness of 50~$μ$m were irradiated in steps of roughly 2$\times$ up to a fluence of $3\times10^{15}~\mathrm{n_{eq}cm^{-2}}$. As a function of the fluence, the collected charge and time resolution of the irradiated sensors will be reported for operation at $-30^{\circ}$. △ Less

Submitted 28 April, 2020; originally announced April 2020.

Effect of deep gain layer and Carbon infusion on LGAD radiation hardness

Authors: R Padilla, C. Labitan, Z. Galloway, C. Gee, S. M. Mazza, F. McKinney-Martinez, H. F. -W. Sadrozinski, A. Seiden, B. Schumm, M. Wilder, Y. Zhao, H. Ren, Y. **, M. Lockerby, V. Cindro, G. Kramberger, I. Mandiz, M. Mikuz, M. Zavrtanik, R. Arcidiacono, N. Cartiglia, M. Ferrero, M. Mandurrino, V. Sola, A. Staiano

Abstract: The properties of 50 um thick Low Gain Avalanche Diode (LGAD) detectors manufactured by Hamamatsu photonics (HPK) and Fondazione Bruno Kessler (FBK) were tested before and after irradiation with 1 MeV neutrons. Their performance were measured in charge collection studies using b-particles from a 90Sr source and in capacitance-voltage scans (C-V) to determine the bias to deplete the gain layer. Car… ▽ More The properties of 50 um thick Low Gain Avalanche Diode (LGAD) detectors manufactured by Hamamatsu photonics (HPK) and Fondazione Bruno Kessler (FBK) were tested before and after irradiation with 1 MeV neutrons. Their performance were measured in charge collection studies using b-particles from a 90Sr source and in capacitance-voltage scans (C-V) to determine the bias to deplete the gain layer. Carbon infusion to the gain layer of the sensors was tested by FBK in the UFSD3 production. HPK instead produced LGADs with a very thin, highly doped and deep multiplication layer. The sensors were exposed to a neutron fluence from 4e14 neq/cm2 to 4e15 neq/cm2. The collected charge and the timing resolution were measured as a function of bias voltage at -30C, furthermore the profile of the capacitance over voltage of the sensors was measured. △ Less

Submitted 27 July, 2020; v1 submitted 10 April, 2020; originally announced April 2020.

Comments: 13 pages, 10 figures, 16 references

Layout and Performance of HPK Prototype LGAD Sensors for the High-Granularity Timing Detector

Authors: X. Yang, S. Alderweireldt, N. Atanov, M. K. Ayoub, J. Barreiro Guimaraes da Costa, L. Castillo Garcia, H. Chen, S. Christie, V. Cindro, H. Cui, G. D'Amen, Y. Davydov, Y. Y. Fan, Z. Galloway, J. J. Ge, C. Gee, G. Giacomini, E. L. Gkougkousis, C. Grieco, S. Grinstein, J. Grosse-Knetter, S. Guindon, S. Han, A. Howard, Y. P. Huang , et al. (54 additional authors not shown)

Abstract: The High-Granularity Timing Detector is a detector proposed for the ATLAS Phase II upgrade. The detector, based on the Low-Gain Avalanche Detector (LGAD) technology will cover the pseudo-rapidity region of $2.4<|η|<4.0$ with two end caps on each side and a total area of 6.4 $m^2$. The timing performance can be improved by implanting an internal gain layer that can produce signal with a fast rising… ▽ More The High-Granularity Timing Detector is a detector proposed for the ATLAS Phase II upgrade. The detector, based on the Low-Gain Avalanche Detector (LGAD) technology will cover the pseudo-rapidity region of $2.4<|η|<4.0$ with two end caps on each side and a total area of 6.4 $m^2$. The timing performance can be improved by implanting an internal gain layer that can produce signal with a fast rising edge, which improve significantly the signal-to-noise ratio. The required average timing resolution per track for a minimum-ionising particle is 30 ps at the start and 50 ps at the end of the HL-LHC operation. This is achieved with several layers of LGAD. The innermost region of the detector would accumulate a 1 MeV-neutron equivalent fluence up to $2.5 \times 10^{15} cm^{-2}$ before being replaced during the scheduled shutdowns. The addition of this new detector is expected to play an important role in the mitigation of high pile-up at the HL-LHC. The layout and performance of the various versions of LGAD prototypes produced by Hamamatsu (HPK) have been studied by the ATLAS Collaboration. The breakdown voltages, depletion voltages, inter-pad gaps, collected charge as well as the time resolution have been measured and the production yield of large size sensors has been evaluated. △ Less

Submitted 31 March, 2020; originally announced March 2020.

Comments: 17 pages, 20 figures

Silicon Sensors for Future Particle Trackers

Authors: N. Cartiglia, R. Arcidiacono, G. Borghi, M. Boscardin, M. Costa, Z. Galloway, F. Fausti, M. Ferrero, F. Ficorella, M. Mandurrino, S. Mazza, E. J. Olave, G. Paternoster, F. Siviero, H. F-W. Sadrozinski, V. Sola, A. Staiano, A. Seiden, M. Tornago, Y. Zhao

Abstract: Several future high-energy physics facilities are currently being planned. The proposed projects include high energy $e^+ e^-$ circular and linear colliders, hadron colliders and muon colliders, while the Electron-Ion Collider (EIC) has already been approved for construction at the Brookhaven National Laboratory. Each proposal has its own advantages and disadvantages in term of readiness, cost, sc… ▽ More Several future high-energy physics facilities are currently being planned. The proposed projects include high energy $e^+ e^-$ circular and linear colliders, hadron colliders and muon colliders, while the Electron-Ion Collider (EIC) has already been approved for construction at the Brookhaven National Laboratory. Each proposal has its own advantages and disadvantages in term of readiness, cost, schedule and physics reach, and each proposal requires the design and production of specific new detectors. This paper first presents the performances required to the future silicon tracking systems at the various new facilities, and then it illustrates a few possibilities for the realization of such silicon trackers. The challenges posed by the future facilities require a new family of silicon detectors, where features such as impact ionization, radiation damage saturation, charge sharing, and analog readout are exploited to meet these new demands. △ Less

Submitted 31 March, 2020; originally announced March 2020.

Experimental Study of Acceptor Removal in UFSD

Authors: Y. **, H. Ren, S. Christie, Z. Galloway, C. Gee, C. Labitan, M. Lockerby, F. Martinez-McKinney, S. M. Mazza, R. Padilla, H. F. -W. Sadrozinski, B. Schumm, A. Seiden, M. Wilder, W. Wyatt, Y. Zhao, R. Arcidiacono, N. Cartiglia, M. Ferrero, M. Mandurrino, F. Siviero, V. Sola, M. Tornago, V. Cindro, A. Howard , et al. (3 additional authors not shown)

Abstract: The performance of the Ultra-Fast Silicon Detectors (UFSD) after irradiation with neutrons and protons is compromised by the removal of acceptors in the thin layer below the junction responsible for the gain. This effect is tested both with C-V measurements of the do** concentration and with measurements of charge collection using charged particles. We find a perfect linear correlation between t… ▽ More The performance of the Ultra-Fast Silicon Detectors (UFSD) after irradiation with neutrons and protons is compromised by the removal of acceptors in the thin layer below the junction responsible for the gain. This effect is tested both with C-V measurements of the do** concentration and with measurements of charge collection using charged particles. We find a perfect linear correlation between the bias voltage to deplete the gain layer determined with C-V and the bias voltage to collect a defined charge, measured with charge collection. An example for the usefulness of this correlation is presented. △ Less

Submitted 16 September, 2020; v1 submitted 16 March, 2020; originally announced March 2020.

Comments: 14 pages, 10 Figs., Sumitted to HSTD12 Hiroshima 2019

Tracking particles at fluences 5-10 $\cdot$1E16 $n_{eq}$/cm$^2$

Authors: N. Cartiglia, H. Sadrozinski, A. Seiden

Abstract: This paper presents the possibility of using very thin Low Gain Avalanche Diodes (LGAD) ($25 - 50μ$m thick) as tracking detector at future hadron colliders, where particle fluence will be above $10^{16}\; n_{eq}/cm^2$. In the present design, silicon sensors at the High-Luminosity LHC will be 100- 200 $μ$m thick, generating, before irradiation, signals of 1-2 fC. This contribution shows how very th… ▽ More This paper presents the possibility of using very thin Low Gain Avalanche Diodes (LGAD) ($25 - 50μ$m thick) as tracking detector at future hadron colliders, where particle fluence will be above $10^{16}\; n_{eq}/cm^2$. In the present design, silicon sensors at the High-Luminosity LHC will be 100- 200 $μ$m thick, generating, before irradiation, signals of 1-2 fC. This contribution shows how very thin LGAD can provide signals of the same magnitude via the interplay of gain in the gain layer and gain in the bulk up to fluences above $10^{16}\; n_{eq}/cm^2$: up to fluences of 0.1-0.3$\cdot 10^{16}\; n_{eq}/cm^2$, thin LGADs maintain a gain of $\sim$ 5-10 while at higher fluences the increased bias voltage will trigger the onset of multiplication in the bulk, providing the same gain as previously obtained in the gain layer. Key to this idea is the possibility of a reliable, high-density LGAD design able to hold large bias voltages ($\sim$ 500V). △ Less

Submitted 30 August, 2019; originally announced August 2019.

Proprieties of FBK UFSDs after neutron and proton irradiation up to 6*10e15 neq/cm2

Authors: S. M. Mazza, E. Estrada, Z. Galloway, C. Gee, A. Goto, Z. Luce, F. McKinney-Martinez, R. Rodriguez, H. F. -W. Sadrozinski, A. Seiden, B. Smithers, Y. Zhao, V. Cindro, G. Kramberger, I. Mandić, M. Mikuž, M. Zavrtanik R. Arcidiacono, N. Cartiglia, M. Ferrero, M. Mandurrino, V. Sola, A. Staiano, M. Boscardin, G. F. Della Betta, F. Ficorella , et al. (2 additional authors not shown)

Abstract: The properties of 60-μm thick Ultra-Fast Silicon Detectors (UFSD) detectors manufactured by Fondazione Bruno Kessler (FBK), Trento (Italy) were tested before and after irradiation with minimum ionizing particles (MIPs) from a 90Sr \b{eta}-source . This FBK production, called UFSD2, has UFSDs with gain layer made of Boron, Boron low-diffusion, Gallium, Carbonated Boron and Carbonated. The irradiati… ▽ More The properties of 60-μm thick Ultra-Fast Silicon Detectors (UFSD) detectors manufactured by Fondazione Bruno Kessler (FBK), Trento (Italy) were tested before and after irradiation with minimum ionizing particles (MIPs) from a 90Sr \b{eta}-source . This FBK production, called UFSD2, has UFSDs with gain layer made of Boron, Boron low-diffusion, Gallium, Carbonated Boron and Carbonated. The irradiation with neutrons took place at the TRIGA reactor in Ljubljana, while the proton irradiation took place at CERN SPS. The sensors were exposed to a neutron fluence of 4*10e14, 8*1014, 1.5*10e15, 3*10e15, 6*10e15 neq/cm2 and to a proton fluence of 9.6*10e14 p/cm2, equivalent to a fluence of 6*10e14 neq/cm2. The internal gain and the timing resolution were measured as a function of bias voltage at -20C. The timing resolution was extracted from the time difference with a second calibrated UFSD in coincidence, using the constant fraction method for both. △ Less

Submitted 18 March, 2020; v1 submitted 15 April, 2018; originally announced April 2018.

Comments: arXiv admin note: text overlap with arXiv:1803.02690

Beam test measurements of Low Gain Avalanche Detector single pads and arrays for the ATLAS High Granularity Timing Detector

Authors: C. Allaire, J. Benitez, M. Bomben, G. Calderini, M. Carulla, E. Cavallaro, A. Falou, D. Flores, P. Freeman, Z. Galloway, E. L. Gkougkousis, H. Grabas, S. Grinstein, B. Gruey, S. Guindon, A. M. Henriques Correia, S. Hidalgo, A. Kastanas, C. Labitan, D. Lacour, J. Lange, F. Lanni, B. Lenzi, Z. Luce, N. Makovec , et al. (19 additional authors not shown)

Abstract: For the high luminosity upgrade of the LHC at CERN, ATLAS is considering the addition of a High Granularity Timing Detector (HGTD) in front of the end cap and forward calorimeters at |z| = 3.5 m and covering the region 2.4 < |η| < 4 to help reducing the effect of pile-up. The chosen sensors are arrays of 50 μm thin Low Gain Avalanche Detectors (LGAD). This paper presents results on single LGAD sen… ▽ More For the high luminosity upgrade of the LHC at CERN, ATLAS is considering the addition of a High Granularity Timing Detector (HGTD) in front of the end cap and forward calorimeters at |z| = 3.5 m and covering the region 2.4 < |η| < 4 to help reducing the effect of pile-up. The chosen sensors are arrays of 50 μm thin Low Gain Avalanche Detectors (LGAD). This paper presents results on single LGAD sensors with a surface area of 1.3x1.3 mm2 and arrays with 2x2 pads with a surface area of 2x2 mm^2 or 3x3 mm^2 each and different implant doses of the p+ multiplication layer. They are obtained from data collected during a beam test campaign in Autumn 2016 with a pion beam of 120 GeV energy at the CERN SPS. In addition to several quantities measured inclusively for each pad, the gain, efficiency and time resolution have been estimated as a function of the position of the incident particle inside the pad by using a beam telescope with a position resolution of few μm. Different methods to measure the time resolution are compared, yielding consistent results. The sensors with a surface area of 1.3x1.3 mm^2 have a time resolution of about 40 ps for a gain of 20 and of about 27 ps for a gain of 50 and fulfill the HGTD requirements. Larger sensors have, as expected, a degraded time resolution. All sensors show very good efficiency and time resolution uniformity. △ Less

Submitted 9 August, 2018; v1 submitted 2 April, 2018; originally announced April 2018.

Journal ref: JINST 13 P06017 (2018)

Production and Integration of the ATLAS Insertable B-Layer

Authors: B. Abbott, J. Albert, F. Alberti, M. Alex, G. Alimonti, S. Alkire, P. Allport, S. Altenheiner, L. Ancu, E. Anderssen, A. Andreani, A. Andreazza, B. Axen, J. Arguin, M. Backhaus, G. Balbi, J. Ballansat, M. Barbero, G. Barbier, A. Bassalat, R. Bates, P. Baudin, M. Battaglia, T. Beau, R. Beccherle , et al. (352 additional authors not shown)

Abstract: During the shutdown of the CERN Large Hadron Collider in 2013-2014, an additional pixel layer was installed between the existing Pixel detector of the ATLAS experiment and a new, smaller radius beam pipe. The motivation for this new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the robustness and performance of the ATLAS tracking system, given the higher instantaneous and i… ▽ More During the shutdown of the CERN Large Hadron Collider in 2013-2014, an additional pixel layer was installed between the existing Pixel detector of the ATLAS experiment and a new, smaller radius beam pipe. The motivation for this new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the robustness and performance of the ATLAS tracking system, given the higher instantaneous and integrated luminosities realised following the shutdown. Because of the extreme radiation and collision rate environment, several new radiation-tolerant sensor and electronic technologies were utilised for this layer. This paper reports on the IBL construction and integration prior to its operation in the ATLAS detector. △ Less

Submitted 6 June, 2018; v1 submitted 2 March, 2018; originally announced March 2018.

Comments: 90 pages in total. Author list: ATLAS IBL Collaboration, starting page 2. 69 figures, 20 tables. Published in Journal of Instrumentation. All figures available at: https://atlas.web.cern.ch/Atlas/GROUPS/PHYSICS/PLOTS/PIX-2018-001

Journal ref: Journal of Instrumentation JINST 13 T05008 (2018)

Radiation resistant LGAD design

Authors: M. Ferrero, R. Arcidiacono, M. Barozzi, M. Boscardin, N. Cartiglia, G. F. Dalla Betta, Z. Galloway, M. Mandurrino, S. Mazza, G. Paternoster, F. Ficorella, L. Pancheri, H-F W. Sadrozinski, V. Sola, A. Staiano, A. Seiden, F. Siviero, M. Tornago, Y. Zhao

Abstract: In this paper, we report on the radiation resistance of 50-micron thick LGAD detectors manufactured at the Fondazione Bruno Kessler employing several different do** combinations of the gain layer. LGAD detectors with gain layer do** of Boron, Boron low-diffusion, Gallium, Carbonated Boron and Carbonated Gallium have been designed and successfully produced. These sensors have been exposed to ne… ▽ More In this paper, we report on the radiation resistance of 50-micron thick LGAD detectors manufactured at the Fondazione Bruno Kessler employing several different do** combinations of the gain layer. LGAD detectors with gain layer do** of Boron, Boron low-diffusion, Gallium, Carbonated Boron and Carbonated Gallium have been designed and successfully produced. These sensors have been exposed to neutron fluences up to $φ_n \sim 3 \cdot 10^{16}\; n/cm^2$ and to proton fluences up to $φ_p \sim 9\cdot10^{15}\; p/cm^2$ to test their radiation resistance. The experimental results show that Gallium-doped LGADs are more heavily affected by initial acceptor removal than Boron-doped LGAD, while the presence of Carbon reduces initial acceptor removal both for Gallium and Boron do**. Boron low-diffusion shows a higher radiation resistance than that of standard Boron implant, indicating a dependence of the initial acceptor removal mechanism upon the implant width. This study also demonstrates that proton irradiation is at least twice more effective in producing initial acceptor removal, making proton irradiation far more damaging than neutron irradiation. △ Less

Submitted 31 August, 2018; v1 submitted 5 February, 2018; originally announced February 2018.

Comments: 22 pages, 17 figures

Radiation Hardness of Thin Low Gain Avalanche Detectors

Authors: G. Kramberger, M. Carulla, E. Cavallaro, V. Cindro, D. Flores, Z. Galloway, S. Grinstein, S. Hidalgo, V. Fadeyev, J. Lange, I. Mandic, G. Medin, A. Merlos, F. McKinney-Martinez, M. Mikuz, D. Quirion, G. Pellegrini, M. Petek, H. F-W. Sadrozinski, A. Seiden, M. Zavrtanik

Abstract: Low Gain Avalanche Detectors (LGAD) are based on a n++-p+-p-p++ structure where an appropriate do** of the multiplication layer (p+) leads to high enough electric fields for impact ionization. Gain factors of few tens in charge significantly improve the resolution of timing measurements, particularly for thin detectors, where the timing performance was shown to be limited by Landau fluctuations.… ▽ More Low Gain Avalanche Detectors (LGAD) are based on a n++-p+-p-p++ structure where an appropriate do** of the multiplication layer (p+) leads to high enough electric fields for impact ionization. Gain factors of few tens in charge significantly improve the resolution of timing measurements, particularly for thin detectors, where the timing performance was shown to be limited by Landau fluctuations. The main obstacle for their operation is the decrease of gain with irradiation, attributed to effective acceptor removal in the gain layer. Sets of thin sensors were produced by two different producers on different substrates, with different gain layer do** profiles and thicknesses (45, 50 and 80 um). Their performance in terms of gain/collected charge and leakage current was compared before and after irradiation with neutrons and pions up to the equivalent fluences of 5e15 cm-2. Transient Current Technique and charge collection measurements with LHC speed electronics were employed to characterize the detectors. The thin LGAD sensors were shown to perform much better than sensors of standard thickness (~300 um) and offer larger charge collection with respect to detectors without gain layer for fluences <2e15 cm-2. Larger initial gain prolongs the beneficial performance of LGADs. Pions were found to be more damaging than neutrons at the same equivalent fluence, while no significant difference was found between different producers. At very high fluences and bias voltages the gain appears due to deep acceptors in the bulk, hence also in thin standard detectors. △ Less

Submitted 16 November, 2017; originally announced November 2017.

Properties of HPK UFSD after neutron irradiation up to 6e15 n/cm2

Authors: Z. Galloway, V. Fadeyev, P. Freeman, E. Gkougkousis, B. Gruey, C. A. Labitan, Z. Luce, F. McKinney-Martinez, H. F. -W. Sadrozinski, A. Seiden, E. Spencer, M. Wilder, N. Woods, A. Zatserklyaniy, Y. Zhao, N. Cartiglia, M. Ferrero, S. Giordanengo, M. Mandurrino, A. Staiano, V. Sola, F. Cenna, F. Fausti, R. Arcidiacono, F. Carnasecchi , et al. (5 additional authors not shown)

Abstract: In this paper we report results from a neutron irradiation campaign of Ultra-Fast Silicon Detectors (UFSD) with fluences of 1e14, 3e14, 6e14, 1e15, 3e15, 6e15 n/cm2. The UFSD used in this study are circular 50 micro-meter thick Low-Gain Avalanche Detectors (LGAD), with a 1.0 mm diameter active area. They have been produced by Hamamatsu Photonics (HPK), Japan, with pre-radiation internal gain in th… ▽ More In this paper we report results from a neutron irradiation campaign of Ultra-Fast Silicon Detectors (UFSD) with fluences of 1e14, 3e14, 6e14, 1e15, 3e15, 6e15 n/cm2. The UFSD used in this study are circular 50 micro-meter thick Low-Gain Avalanche Detectors (LGAD), with a 1.0 mm diameter active area. They have been produced by Hamamatsu Photonics (HPK), Japan, with pre-radiation internal gain in the range 10-100 depending on the bias voltage. The sensors were tested pre-irradiation and post-irradiation with minimum ionizing particle (MIPs) from a 90Sr based \b{eta}-source. The leakage current, internal gain and the timing resolution were measured as a function of bias voltage at -20C and -30C. The timing resolution was extracted from the time difference with a second calibrated UFSD in coincidence, using the constant fraction method for both. The dependence of the gain upon the irradiation fluence is consistent with the concept of acceptor removal and the gain decreases from about 80 pre-irradiation to 7 after a fluence of 6e15 n/cm2. Consequently, the timing resolution was found to deteriorate from 20 ps to 50 ps. The results indicate that the most accurate time resolution is obtained at a value of the constant fraction discriminator (CFD) threshold used to determine the time of arrival varying with fluence, from 10% pre-radiation to 60% at the highest fluence. Key changes to the pulse shape induced by irradiation, i.e. (i) a reduce sensitivity of the pulse shape on the initial non-uniform charge deposition, (ii) the shortening of the rise time and (iii) the reduced pulse height, were compared with the WF2 simulation program and found to be in agreement. △ Less

Submitted 10 April, 2020; v1 submitted 16 July, 2017; originally announced July 2017.

Comments: 18 pages, 21 figures, 1 table

4-Dimensional Tracking with Ultra-Fast Silicon Detectors

Authors: Hartmut F. -W. Sadrozinski, Abraham Seiden, Nicolò Cartiglia

Abstract: The evolution of particle detectors has always pushed the technological limit in order to provide enabling technologies to researchers in all fields of science. One archetypal example is the evolution of silicon detectors, from a system with a few channels 30 years ago, to the tens of millions of independent pixels currently used to track charged particles in all major particle physics experiments… ▽ More The evolution of particle detectors has always pushed the technological limit in order to provide enabling technologies to researchers in all fields of science. One archetypal example is the evolution of silicon detectors, from a system with a few channels 30 years ago, to the tens of millions of independent pixels currently used to track charged particles in all major particle physics experiments. Nowadays, silicon detectors are ubiquitous not only in research laboratories but in almost every high-tech apparatus, from portable phones to hospitals. In this contribution, we present a new direction in the evolution of silicon detectors for charge particle tracking, namely the inclusion of very accurate timing information. This enhancement of the present silicon detector paradigm is enabled by the inclusion of controlled low gain in the detector response, therefore increasing the detector output signal sufficiently to make timing measurement possible. After providing a short overview of the advantage of this new technology, we present the necessary conditions that need to be met for both sensor and readout electronics in order to achieve 4-dimensional tracking. In the last section we present the experimental results, demonstrating the validity of our research path. △ Less

Submitted 3 July, 2017; v1 submitted 27 April, 2017; originally announced April 2017.

Comments: 72 pages, 3 tables, 55 figures

Energy and time measurements with high-granular silicon devices

Authors: Marcello Mannelli, Roman Pöschl, Abraham Seiden

Abstract: This note is a short summary of the workshop on "Energy and time measurements with high-granular silicon devices" that took place on the 13/6/16 and the 14/6/16 at DESY/Hamburg in the frame of the first AIDA-2020 Annual Meeting. This note tries to put forward trends that could be spotted and to emphasise in particular open issues that were addressed by the speakers. This note is a short summary of the workshop on "Energy and time measurements with high-granular silicon devices" that took place on the 13/6/16 and the 14/6/16 at DESY/Hamburg in the frame of the first AIDA-2020 Annual Meeting. This note tries to put forward trends that could be spotted and to emphasise in particular open issues that were addressed by the speakers. △ Less

Submitted 6 April, 2017; v1 submitted 5 April, 2017; originally announced April 2017.

Report number: AIDA-2020-NOTE-2017-005, LAL 17-023

Beam test results of a 16 ps timing system based on ultra-fast silicon detectors

Authors: N. Cartiglia, A. Staiano, V. Sola, R. Arcidiacono, R. Cirio, F. Cenna, M. Ferrero, V. Monaco, R. Mulargia, M. Obertino, F. Ravera, R. Sacchi, A. Bellora, S. Durando, M. Mandurrino, N. Minafra, V. Fadeyev, P. Freeman, Z. Galloway, E. Gkougkousis, H. Grabas, B. Gruey, C. A. Labitan, R. Losakul, Z. Luce , et al. (18 additional authors not shown)

Abstract: In this paper we report on the timing resolution of the first production of 50 micro-meter thick Ultra-Fast Silicon Detectors (UFSD) as obtained in a beam test with pions of 180 GeV/c momentum. UFSD are based on the Low-Gain Avalanche Detectors (LGAD) design, employing n-on-p silicon sensors with internal charge multiplication due to the presence of a thin, low-resistivity diffusion layer below th… ▽ More In this paper we report on the timing resolution of the first production of 50 micro-meter thick Ultra-Fast Silicon Detectors (UFSD) as obtained in a beam test with pions of 180 GeV/c momentum. UFSD are based on the Low-Gain Avalanche Detectors (LGAD) design, employing n-on-p silicon sensors with internal charge multiplication due to the presence of a thin, low-resistivity diffusion layer below the junction. The UFSD used in this test belongs to the first production of thin (50 μm) sensors, with an pad area of 1.4 mm2. The gain was measured to vary between 5 and 70 depending on the bias voltage. The experimental setup included three UFSD and a fast trigger consisting of a quartz bar readout by a SiPM. The timing resolution, determined comparing the time of arrival of the particle in one or more UFSD and the trigger counter, for single UFSD was measured to be 35 ps for a bias voltage of 200 V, and 26 ps for a bias voltage of 240 V, and for the combination of 3 UFSD to be 20 ps for a bias voltage of 200 V, and 15 ps for a bias voltage of 240 V. △ Less

Submitted 3 January, 2017; v1 submitted 30 August, 2016; originally announced August 2016.

Comments: 7 pages, 8 figures, 1 table, Subm. to NIM A

Journal ref: NIM A850, 1 April 2017, pages 83-88

First Observation of CP Violation in B0->D(*)CP h0 Decays by a Combined Time-Dependent Analysis of BaBar and Belle Data

Authors: The BaBar, Belle Collaborations, :, A. Abdesselam, I. Adachi, A. Adametz, T. Adye, H. Ahmed, H. Aihara, S. Akar, M. S. Alam, J. Albert, S. Al Said, R. Andreassen, C. Angelini, F. Anulli, K. Arinstein, N. Arnaud, D. M. Asner, D. Aston, V. Aulchenko, T. Aushev, R. Ayad, V. Babu, I. Badhrees , et al. (450 additional authors not shown)

Abstract: We report a measurement of the time-dependent CP asymmetry of B0->D(*)CP h0 decays, where the light neutral hadron h0 is a pi0, eta or omega meson, and the neutral D meson is reconstructed in the CP eigenstates K+ K-, K0S pi0 or K0S omega. The measurement is performed combining the final data samples collected at the Y(4S) resonance by the BaBar and Belle experiments at the asymmetric-energy B fac… ▽ More We report a measurement of the time-dependent CP asymmetry of B0->D(*)CP h0 decays, where the light neutral hadron h0 is a pi0, eta or omega meson, and the neutral D meson is reconstructed in the CP eigenstates K+ K-, K0S pi0 or K0S omega. The measurement is performed combining the final data samples collected at the Y(4S) resonance by the BaBar and Belle experiments at the asymmetric-energy B factories PEP-II at SLAC and KEKB at KEK, respectively. The data samples contain ( 471 +/- 3 ) x 10^6 BB pairs recorded by the BaBar detector and ( 772 +/- 11 ) x 10^6, BB pairs recorded by the Belle detector. We measure the CP asymmetry parameters -eta_f S = +0.66 +/- 0.10 (stat.) +/- 0.06 (syst.) and C = -0.02 +/- 0.07 (stat.) +/- 0.03 (syst.). These results correspond to the first observation of CP violation in B0->D(*)CP h0 decays. The hypothesis of no mixing-induced CP violation is excluded in these decays at the level of 5.4 standard deviations. △ Less

Submitted 20 July, 2015; v1 submitted 15 May, 2015; originally announced May 2015.

Comments: 9 pages, 2 figures, submitted to Physical Review Letters

The Physics of the B Factories

Authors: A. J. Bevan, B. Golob, Th. Mannel, S. Prell, B. D. Yabsley, K. Abe, H. Aihara, F. Anulli, N. Arnaud, T. Aushev, M. Beneke, J. Beringer, F. Bianchi, I. I. Bigi, M. Bona, N. Brambilla, J. B rodzicka, P. Chang, M. J. Charles, C. H. Cheng, H. -Y. Cheng, R. Chistov, P. Colangelo, J. P. Coleman, A. Drutskoy , et al. (2009 additional authors not shown)

Abstract: This work is on the Physics of the B Factories. Part A of this book contains a brief description of the SLAC and KEK B Factories as well as their detectors, BaBar and Belle, and data taking related issues. Part B discusses tools and methods used by the experiments in order to obtain results. The results themselves can be found in Part C. Please note that version 3 on the archive is the auxiliary… ▽ More This work is on the Physics of the B Factories. Part A of this book contains a brief description of the SLAC and KEK B Factories as well as their detectors, BaBar and Belle, and data taking related issues. Part B discusses tools and methods used by the experiments in order to obtain results. The results themselves can be found in Part C. Please note that version 3 on the archive is the auxiliary version of the Physics of the B Factories book. This uses the notation alpha, beta, gamma for the angles of the Unitarity Triangle. The nominal version uses the notation phi_1, phi_2 and phi_3. Please cite this work as Eur. Phys. J. C74 (2014) 3026. △ Less

Submitted 31 October, 2015; v1 submitted 24 June, 2014; originally announced June 2014.

Comments: 928 pages, version 3 (arXiv:1406.6311v3) corresponds to the alpha, beta, gamma version of the book, the other versions use the phi1, phi2, phi3 notation

Report number: SLAC-PUB-15968, KEK Preprint 2014-3

Journal ref: Eur. Phys. J. C74 (2014) 3026

Planning the Future of U.S. Particle Physics (Snowmass 2013): Chapter 8: Instrumentation Frontier

Authors: M. Demarteau, R. Lipton, H. Nicholson, I. Shipsey, D. Akerib, A. Albayrak-Yetkin, J. Alexander, J. Anderson, M. Artuso, D. Asner, R. Ball, M. Battaglia, C. Bebek, J. Beene, Y. Benhammou, E. Bentefour, M. Bergevin, A. Bernstein, B. Bilki, E. Blucher, G. Bolla, D. Bortoletto, N. Bowden, G. Brooijmans, K. Byrum , et al. (189 additional authors not shown)

Abstract: These reports present the results of the 2013 Community Summer Study of the APS Division of Particles and Fields ("Snowmass 2013") on the future program of particle physics in the U.S. Chapter 8, on the Instrumentation Frontier, discusses the instrumentation needs of future experiments in the Energy, Intensity, and Cosmic Frontiers, promising new technologies for particle physics research, and iss… ▽ More These reports present the results of the 2013 Community Summer Study of the APS Division of Particles and Fields ("Snowmass 2013") on the future program of particle physics in the U.S. Chapter 8, on the Instrumentation Frontier, discusses the instrumentation needs of future experiments in the Energy, Intensity, and Cosmic Frontiers, promising new technologies for particle physics research, and issues of gathering resources for long-term research in this area. △ Less

Submitted 23 January, 2014; originally announced January 2014.

Comments: 50 pages

Benefits to the U.S. from Physicists Working at Accelerators Overseas

Authors: Jacob Anderson, Raymond Brock, Yuri Gershtein, Nicholas Hadley, Michael Harrison, Meenakshi Narain, Jason Nielsen, Fred Olness, Bjoern Penning, Michael Peskin, Eric Prebys, Marc Ross, Salvatore Rappoccio, Abraham Seiden, Ryszard Stroynowski

Abstract: We illustrate benefits to the U.S. economy and technological infrastructure of U.S. participation in accelerators overseas. We discuss contributions to experimental hardware and analysis and to accelerator technology and components, and benefits stemming from the involvement of U.S. students and postdoctoral fellows in global scientific collaborations. Contributed to the proceedings of the Snowmas… ▽ More We illustrate benefits to the U.S. economy and technological infrastructure of U.S. participation in accelerators overseas. We discuss contributions to experimental hardware and analysis and to accelerator technology and components, and benefits stemming from the involvement of U.S. students and postdoctoral fellows in global scientific collaborations. Contributed to the proceedings of the Snowmass 2013 Community Summer Study. △ Less

Submitted 17 December, 2013; originally announced December 2013.

Comments: 23 pages, 1 figure

Report number: SLAC-PUB-15859

Performance of Ultra-Fast Silicon Detectors

Authors: N. Cartiglia, M. Baselga, G. Dellacasa, S. Ely, V. Fadeyev, Z. Galloway, F. Marchetto, S. Maroiu, G. Mazza, J. Ngo, M. Obertino, C. Parker, A. Rivetti, D. Shumacher, H. F-W. Sadrozinski, A. Seiden, A. Zatserklyaniy

Abstract: The development of Low-Gain Avalanche Detectors has opened up the possibility of manufacturing silicon detectors with signal larger than that of traditional sensors. In this paper we explore the timing performance of Low-Gain Avalanche Detectors, and in particular we demonstrate the possibility of obtaining ultra-fast silicon detector with time resolution of less than 20 picosecond. The development of Low-Gain Avalanche Detectors has opened up the possibility of manufacturing silicon detectors with signal larger than that of traditional sensors. In this paper we explore the timing performance of Low-Gain Avalanche Detectors, and in particular we demonstrate the possibility of obtaining ultra-fast silicon detector with time resolution of less than 20 picosecond. △ Less

Submitted 5 December, 2013; v1 submitted 4 December, 2013; originally announced December 2013.

Comments: 10 pages, 10 figures

Evidence for the decay B0 --> omega omega and search for B0 --> omega phi

Authors: The BABAR Collaboration, J. P. Lees, V. Poireau, V. Tisserand, E. Grauges, A. Palano, G. Eigen, B. Stugu, D. N. Brown, L. T. Kerth, Yu. G. Kolomensky, M. J. Lee, G. Lynch, H. Koch, T. Schroeder, C. Hearty, T. S. Mattison, J. A. McKenna, R. Y. So, A. Khan, V. E. Blinov, A. R. Buzykaev, V. P. Druzhinin, V. B. Golubev, E. A. Kravchenko , et al. (312 additional authors not shown)

Abstract: We describe searches for B meson decays to the charmless vector-vector final states omega omega and omega phi with 471 x 10^6 B Bbar pairs produced in e+ e- annihilation at sqrt(s) = 10.58 GeV using the BABAR detector at the PEP-II collider at the SLAC National Accelerator Laboratory. We measure the branching fraction B(B0 --> omega omega) = (1.2 +- 0.3 +0.3-0.2) x 10^-6, where the first uncertain… ▽ More We describe searches for B meson decays to the charmless vector-vector final states omega omega and omega phi with 471 x 10^6 B Bbar pairs produced in e+ e- annihilation at sqrt(s) = 10.58 GeV using the BABAR detector at the PEP-II collider at the SLAC National Accelerator Laboratory. We measure the branching fraction B(B0 --> omega omega) = (1.2 +- 0.3 +0.3-0.2) x 10^-6, where the first uncertainty is statistical and the second is systematic, corresponding to a significance of 4.4 standard deviations. We also determine the upper limit B(B0 --> omega phi) < 0.7 x 10^-6 at 90% confidence level. These measurements provide the first evidence for the decay B0 --> omega omega, and an improvement of the upper limit for the decay B0 --> omega phi. △ Less

Submitted 6 March, 2014; v1 submitted 29 November, 2013; originally announced December 2013.

Comments: 7 pages, 2 postscript figures

Report number: BABAR-PUB-13/018, SLAC-PUB-15846

Journal ref: Phys. Rev. D 89, 051101 (2014)

Sensor Compendium

Authors: M. Artuso, M. Battaglia, G. Bolla, D. Bortoletto, B. Cabrera, J. E. Carlstrom, C. L. Chang, W. Cooper, C. Da Via, M. Demarteau, J. Fast, H. Frisch, M. Garcia-Sciveres, S. Golwala, C. Haber, J. Hall, E. Hoppe, K. D. Irwin, H. Kagan, C. Kenney, A. T. Lee, D. Lynn, J. Orrell, M. Pyle, R. Rusack , et al. (7 additional authors not shown)

Abstract: Sensors play a key role in detecting both charged particles and photons for all three frontiers in Particle Physics. The signals from an individual sensor that can be used include ionization deposited, phonons created, or light emitted from excitations of the material. The individual sensors are then typically arrayed for detection of individual particles or groups of particles. Mounting of new, e… ▽ More Sensors play a key role in detecting both charged particles and photons for all three frontiers in Particle Physics. The signals from an individual sensor that can be used include ionization deposited, phonons created, or light emitted from excitations of the material. The individual sensors are then typically arrayed for detection of individual particles or groups of particles. Mounting of new, ever higher performance experiments, often depend on advances in sensors in a range of performance characteristics. These performance metrics can include position resolution for passing particles, time resolution on particles impacting the sensor, and overall rate capabilities. In addition the feasible detector area and cost frequently provides a limit to what can be built and therefore is often another area where improvements are important. Finally, radiation tolerance is becoming a requirement in a broad array of devices. We present a status report on a broad category of sensors, including challenges for the future and work in progress to solve those challenges △ Less

Submitted 25 October, 2013; v1 submitted 18 October, 2013; originally announced October 2013.

Comments: 66 pages, Prepared for the Snowmass 2013 Community Summer Study

Report number: Fermilab--?FN--?0971--?PPD, ANL--?HEP--?TR--?13--?51

ATLAS Upgrade Instrumentation in the US

Authors: Gustaaf Brooijmans, Hal Evans, Abe Seiden

Abstract: Planned upgrades of the LHC over the next decade should allow the machine to operate at a center of mass energy of 14 TeV with instantaneous luminosities in the range 5--7e34 cm^-2 s^-1. With these parameters, ATLAS could collect 3,000 fb^-1 of data in approximately 10 years. However, the conditions under which this data would be acquired are much harsher than those currently encountered at the LH… ▽ More Planned upgrades of the LHC over the next decade should allow the machine to operate at a center of mass energy of 14 TeV with instantaneous luminosities in the range 5--7e34 cm^-2 s^-1. With these parameters, ATLAS could collect 3,000 fb^-1 of data in approximately 10 years. However, the conditions under which this data would be acquired are much harsher than those currently encountered at the LHC. For example, the number of proton-proton interactions per bunch crossing will rise from the level of 20--30 per 50 ns crossing observed in 2012 to 140--200 every 25 ns. In order to deepen our understanding of the newly discovered Higgs boson and to extend our searches for physics beyond that new particle, the ATLAS detector, trigger, and readout will have to undergo significant upgrades. In this whitepaper we describe R&D necessary for ATLAS to continue to run effectively at the highest luminosities foreseen from the LHC. Emphasis is placed on those R&D efforts in which US institutions are playing a leading role. △ Less

Submitted 22 July, 2013; originally announced July 2013.

Comments: Snowmass contributed paper, 24 pages, 12 figures

Study of the decay $\bar{B}^{0}\rightarrowΛ_{c}^{+}\bar{p}π^{+}π^{-}$ and its intermediate states

Authors: The Babar Collaboration, J. P. Lees, V. Poireau, V. Tisserand, E. Grauges, A. Palano, G. Eigen, B. Stugu, D. N. Brown, L. T. Kerth, Yu. G. Kolomensky, G. Lynch, H. Koch, T. Schroeder, D. J. Asgeirsson, C. Hearty, T. S. Mattison, J. A. McKenna, R. Y. So, A. Khan, V. E. Blinov, A. R. Buzykaev, V. P. Druzhinin, V. B. Golubev, E. A. Kravchenko , et al. (330 additional authors not shown)

Abstract: We study the decay $\bar{B}^{0}\rightarrowΛ_{c}^{+}\bar{p}π^{+}π^{-}$, reconstructing the Λ_{c}^{+} baryon in the $p K^{-}π^{+}$ mode, using a data sample of $467\times 10^{6}$ $B\bar{B}$ pairs collected with the BaBar detector at the PEP-2 storage rings at SLAC. We measure branching fractions for decays with intermediate $Σ_{c}$ baryons to be… ▽ More We study the decay $\bar{B}^{0}\rightarrowΛ_{c}^{+}\bar{p}π^{+}π^{-}$, reconstructing the Λ_{c}^{+} baryon in the $p K^{-}π^{+}$ mode, using a data sample of $467\times 10^{6}$ $B\bar{B}$ pairs collected with the BaBar detector at the PEP-2 storage rings at SLAC. We measure branching fractions for decays with intermediate $Σ_{c}$ baryons to be ${\cal B}[\bar{B}^{0}\rightarrowΣ_{c}(2455)^{++}\bar{p}π^{-}]=(21.3 \pm 1.0 \pm 1.0 \pm 5.5) \times 10^{-5}$, ${\cal B}[\bar{B}^{0}\rightarrowΣ_{c}(2520)^{++}\bar{p}π^{-}]=(11.5\pm 1.0 \pm 0.5 \pm 3.0)\times 10^{-5}$, ${\cal B}[\bar{B}^{0}\rightarrowΣ_{c}(2455)^{0}\bar{p}π^{+}]=(9.1 \pm 0.7 \pm 0.4 \pm 2.4)\times10^{-5}$, and ${\cal B}[\bar{B}^{0}\rightarrowΣ_{c}(2520)^{0}\bar{p}π^{+}]= (2.2 \pm 0.7 \pm 0.1\pm 0.6) \times 10^{-5}$, where the uncertainties are statistical, systematic, and due to the uncertainty on the $Λ_{c}^{+}\rightarrow\proton\Kmπ^{+}$ branching fraction, respectively. For decays without $Σ_{c}(2455)$ or $Σ_{c}(2520)$ resonances, we measure ${\cal B}[\bar{B}^{0}\rightarrowΛ_{c}^{+}\bar{p}π^{+}π^{-}]_{\mathrm{non-Σ_{c}}}=(79 \pm 4 \pm 4 \pm 20)\times10^{-5}$. The total branching fraction is determined to be ${\cal B}[\bar{B}^{0}\rightarrowΛ_{c}^{+}\bar{p}π^{+}π^{-}]_{\mathrm{total}}=(123 \pm 5 \pm 7 \pm 32)\times10^{-5}$. We examine multibody mass combinations in the resonant three-particle $Σ_{c}\bar{p}π$ final states and in the four-particle $Λ_{c}^{+}\bar{p}π^{+}π^{-}$ final state, and observe different characteristics for the $\bar{p}π$ combination in neutral versus doubly-charged $Σ_{c}$ decays. △ Less

Submitted 28 March, 2013; v1 submitted 1 February, 2013; originally announced February 2013.

Comments: 20 pages, 30 figures

Report number: Babar-PUB-12/028, SLAC-PUB-15363

Search for direct CP-violation in singly-Cabibbo suppressed D+- --> K+ K- pi+- decays

Authors: BaBar Collaboration, J. P. Lees, V. Poireau, V. Tisserand, J. Garra Tico, E. Grauges, A. Palano, G. Eigen, B. Stugu, D. N. Brown, L. T. Kerth, Yu. G. Kolomensky, G. Lynch, H. Koch, T. Schroeder, D. J. Asgeirsson, C. Hearty, T. S. Mattison, J. A. McKenna, R. Y. So, A. Khan, V. E. Blinov, A. R. Buzykaev, V. P. Druzhinin, V. B. Golubev , et al. (338 additional authors not shown)

Abstract: We report on a search for direct CP asymmetry in the singly Cabibbo-suppressed decay D+- --> K+ K- pi+- using a data sample of 476 fb-1 accumulated with the BaBar detector running at and just below the Y(4S) resonance. The CP-violating decay rate asymmetry A_CP is determined to be (0.35 +- 0.30 +- 0.15)%. Model-dependent and model-independent Dalitz plot analysis techniques are used to search for… ▽ More We report on a search for direct CP asymmetry in the singly Cabibbo-suppressed decay D+- --> K+ K- pi+- using a data sample of 476 fb-1 accumulated with the BaBar detector running at and just below the Y(4S) resonance. The CP-violating decay rate asymmetry A_CP is determined to be (0.35 +- 0.30 +- 0.15)%. Model-dependent and model-independent Dalitz plot analysis techniques are used to search for CP-violating asymmetries in the various intermediate states. △ Less

Submitted 21 February, 2013; v1 submitted 8 December, 2012; originally announced December 2012.

Comments: 14 pages, 6 eps figures, to be submitted to PRD

Report number: BABAR-PUB-12/014, SLAC-PUB-15077

Branching fraction and form-factor shape measurements of exclusive charmless semileptonic B decays, and determination of |V_{ub}|

Authors: BABAR Collaboration, J. P. Lees, V. Poireau, V. Tisserand, J. Garra Tico, E. Grauges, A. Palano, G. Eigen, B. Stugu, D. N. Brown, L. T. Kerth, Yu. G. Kolomensky, G. Lynch, H. Koch, T. Schroeder, D. J. Asgeirsson, C. Hearty, T. S. Mattison, J. A. McKenna, R. Y. So, A. Khan, V. E. Blinov, A. R. Buzykaev, V. P. Druzhinin, V. B. Golubev , et al. (340 additional authors not shown)

Abstract: We report the results of a study of the exclusive charmless semileptonic decays, B^0 --> pi^- l^+ nu, B^+ --> pi^0 l^+ nu, B^+ --> omega l^+ nu, B^+ --> eta l^+ nu and B^+ --> eta^' l^+ nu, (l = e or mu) undertaken with approximately 462x10^6 B\bar{B} pairs collected at the Upsilon(4S) resonance with the BABAR detector. The analysis uses events in which the signal B decays are reconstructed with a… ▽ More We report the results of a study of the exclusive charmless semileptonic decays, B^0 --> pi^- l^+ nu, B^+ --> pi^0 l^+ nu, B^+ --> omega l^+ nu, B^+ --> eta l^+ nu and B^+ --> eta^' l^+ nu, (l = e or mu) undertaken with approximately 462x10^6 B\bar{B} pairs collected at the Upsilon(4S) resonance with the BABAR detector. The analysis uses events in which the signal B decays are reconstructed with a loose neutrino reconstruction technique. We obtain partial branching fractions in several bins of q^2, the square of the momentum transferred to the lepton-neutrino pair, for B^0 --> pi^- l^+ nu, B^+ --> pi^0 l^+ nu, B^+ --> omega l^+ nu and B^+ --> eta l^+ nu. From these distributions, we extract the form-factor shapes f_+(q^2) and the total branching fractions BF(B^0 --> pi^- l^+ nu) = (1.45 +/- 0.04_{stat} +/- 0.06_{syst})x10^-4 (combined pi^- and pi^0 decay channels assuming isospin symmetry), BF(B^+ --> omega l^+ nu) = (1.19 +/- 0.16_{stat} +/- 0.09_{syst})x10^-4 and BF(B^+ --> eta l^+ nu) = (0.38 +/- 0.05_{stat} +/- 0.05_{syst})x10^-4. We also measure BF(B^+ --> eta^' l^+ nu) = (0.24 +/- 0.08_{stat} +/- 0.03_{syst})x10^-4. We obtain values for the magnitude of the CKM matrix element V_{ub} by direct comparison with three different QCD calculations in restricted q^2 ranges of B --> pi l^+ nu decays. From a simultaneous fit to the experimental data over the full q^2 range and the FNAL/MILC lattice QCD predictions, we obtain |V_{ub}| = (3.25 +/- 0.31)x10^-3, where the error is the combined experimental and theoretical uncertainty. △ Less

Submitted 6 November, 2012; v1 submitted 6 August, 2012; originally announced August 2012.

Comments: 35 pages, 14 figures, submitted to PRD

Report number: BABAR-PUB12/015; SLAC-PUB-15208

Journal ref: Phys.Rev.D86:092004,2012

Observation of Time Reversal Violation in the B0 Meson System

Authors: The BABAR Collaboration, J. P. Lees, V. Poireau, V. Tisserand, J. Garra Tico, E. Grauges, A. Palanoab, G. Eigen, B. Stugu, D. N. Brown, L. T. Kerth, Yu. G. Kolomensky, G. Lynch, H. Koch, T. Schroeder, D. J. Asgeirsson, C. Hearty, T. S. Mattison, J. A. McKenna, R. Y. So, A. Khan, V. E. Blinov, A. R. Buzykaev, V. P. Druzhinin, V. B. Golubev , et al. (343 additional authors not shown)

Abstract: Although CP violation in the B meson system has been well established by the B factories, there has been no direct observation of time reversal violation. The decays of entangled neutral B mesons into definite flavor states ($B^0$ or $\bar{B}^0$), and $J/ψK_S^0$ or $c\bar{c} K_S^0$ final states (referred to as $B_+$ or $B_-$), allow comparisons between the probabilities of four pairs of T-conjugat… ▽ More Although CP violation in the B meson system has been well established by the B factories, there has been no direct observation of time reversal violation. The decays of entangled neutral B mesons into definite flavor states ($B^0$ or $\bar{B}^0$), and $J/ψK_S^0$ or $c\bar{c} K_S^0$ final states (referred to as $B_+$ or $B_-$), allow comparisons between the probabilities of four pairs of T-conjugated transitions, for example, $\bar{B}^0 \rightarrow B_-$ and $B_- \rightarrow \bar{B}^0$, as a function of the time difference between the two B decays. Using 468 million $B\bar{B}$ pairs produced in $Υ(4S)$ decays collected by the BABAR detector at SLAC, we measure T-violating parameters in the time evolution of neutral B mesons, yielding $ΔS_T^+ = -1.37 \pm 0.14 (stat.) \pm 0.06 (syst.)$ and $ΔS_T^- = 1.17 \pm 0.18 (stat.) \pm 0.11 (syst.)$. These nonzero results represent the first direct observation of T violation through the exchange of initial and final states in transitions that can only be connected by a T-symmetry transformation. △ Less

Submitted 2 January, 2013; v1 submitted 24 July, 2012; originally announced July 2012.

Comments: 7 pages, 3 postscript figures, 1 table, appendix with 4 pages containing supplementary material. Accepted by Phys. Rev. Lett

Report number: BABAR-PUB-12/011; SLAC-PUB-15192

Journal ref: Phys. Rev. Lett. 109, 211801 (2012)

Initial-State Radiation Measurement of the e+e- -> pi+pi-pi+pi- Cross Section

Authors: J. P. Lees, V. Poireau, V. Tisserand, J. Garra Tico, E. Grauges, M. Martinelli, D. A. Milanes, A. Palano, M. Pappagallo, G. Eigen, B. Stugu, D. N. Brown, L. T. Kerth, Yu. G. Kolomensky, G. Lynch, H. Koch, T. Schroeder, D. J. Asgeirsson, C. Hearty, T. S. Mattison, J. A. McKenna, A. Khan, V. E. Blinov, A. R. Buzykaev, V. P. Druzhinin , et al. (362 additional authors not shown)

Abstract: We study the process e+e- -> pi+pi-pi+pi-gamma, with a photon emitted from the initial-state electron or positron, using 454.3 fb^-1 of data collected with the BABAR detector at SLAC, corresponding to approximately 260,000 signal events. We use these data to extract the non-radiative sigma(e+e- ->pi+pi-pi+pi-) cross section in the energy range from 0.6 to 4.5 Gev. The total uncertainty of the cros… ▽ More We study the process e+e- -> pi+pi-pi+pi-gamma, with a photon emitted from the initial-state electron or positron, using 454.3 fb^-1 of data collected with the BABAR detector at SLAC, corresponding to approximately 260,000 signal events. We use these data to extract the non-radiative sigma(e+e- ->pi+pi-pi+pi-) cross section in the energy range from 0.6 to 4.5 Gev. The total uncertainty of the cross section measurement in the peak region is less than 3%, higher in precision than the corresponding results obtained from energy scan data. △ Less

Submitted 27 August, 2012; v1 submitted 26 January, 2012; originally announced January 2012.

Report number: SLAC-PUB-14857

Journal ref: PRD 85, 112009 (2012)

A Measurement of the Semileptonic Branching Fraction of the B_s Meson

Authors: The BaBar Collaboration, J. P. Lees, V. Poireau, V. Tisserand, J. Garra Tico, E. Grauges, M. Martinelli, D. A. Milanes, A. Palano, M. Pappagallo, G. Eigen, B. Stugu, D. N. Brown, L. T. Kerth, Yu. G. Kolomensky, G. Lynch, H. Koch, T. Schroeder, D. J. Asgeirsson, C. Hearty, T. S. Mattison, J. A. McKenna, A. Khan, V. E. Blinov, A. R. Buzykaev , et al. (362 additional authors not shown)

Abstract: We report a measurement of the inclusive semileptonic branching fraction of the B_s meson using data collected with the BaBar detector in the center-of-mass (CM) energy region above the Upsilon(4S) resonance. We use the inclusive yield of phi mesons and the phi yield in association with a high-momentum lepton to perform a simultaneous measurement of the semileptonic branching fraction and the pr… ▽ More We report a measurement of the inclusive semileptonic branching fraction of the B_s meson using data collected with the BaBar detector in the center-of-mass (CM) energy region above the Upsilon(4S) resonance. We use the inclusive yield of phi mesons and the phi yield in association with a high-momentum lepton to perform a simultaneous measurement of the semileptonic branching fraction and the production rate of B_s mesons relative to all B mesons as a function of CM energy. The inclusive semileptonic branching fraction of the B_s meson is determined to be B(B_s to l nu X)=9.5 (+2.5/-2.0)(stat)(+1.1/-1.9)(syst)%, where l indicates the average of e and mu. △ Less

Submitted 10 January, 2012; v1 submitted 25 October, 2011; originally announced October 2011.

Comments: 8 pages, 7 eps figures

Report number: BaBar-Pub-11/021; SLAC-PUB-14653

Journal ref: Phys. Rev. D 85, 011101(R) (2012)

Search for hadronic decays of a light Higgs boson in the radiative decay Upsilon --> gamma A0

Authors: The BABAR Collaboration, J. P. Lees, V. Poireau, V. Tisserand, J. Garra Tico, E. Grauges, M. Martinelli, D. A. Milanes, A. Palano, M. Pappagallo, G. Eigen, B. Stugu, D. N. Brown, L. T. Kerth, Yu. G. Kolomensky, G. Lynch, H. Koch, T. Schroeder, D. J. Asgeirsson, C. Hearty, T. S. Mattison, J. A. McKenna, R. Y. So, A. Khan, V. E. Blinov , et al. (364 additional authors not shown)

Abstract: We search for hadronic decays of a light Higgs boson (A0) produced in radiative decays of an Upsilon(2S) or Upsilon(3S) meson, Upsilon --> gamma A0. The data have been recorded by the BABAR experiment at the Upsilon(3S) and Upsilon(2S) center of mass energies, and include (121.3 \pm 1.2) x 10^6 Upsilon(3S) and (98.3 \pm 0.9) x 10^6 Upsilon(2S) mesons. No significant signal is observed. We set 90%… ▽ More We search for hadronic decays of a light Higgs boson (A0) produced in radiative decays of an Upsilon(2S) or Upsilon(3S) meson, Upsilon --> gamma A0. The data have been recorded by the BABAR experiment at the Upsilon(3S) and Upsilon(2S) center of mass energies, and include (121.3 \pm 1.2) x 10^6 Upsilon(3S) and (98.3 \pm 0.9) x 10^6 Upsilon(2S) mesons. No significant signal is observed. We set 90% confidence level upper limits on the product branching fractions B(Upsilon(nS)-->gamma A0) x B(A0-->hadrons) (n=2 or 3) that range from 1 x 10^{-6} for an A0 mass of 0.3 GeV/c^2 to 8 x 10^{-5} at 7 GeV/c^2. △ Less

Submitted 17 August, 2011; originally announced August 2011.

Comments: 7 pages, 5 postscript figures, submitted to Physical Review Letters

Report number: Report-no: BABAR-PUB-11/019, SLAC-PUB-14541

Observation of the baryonic B decay B0bar --> Lambda_c^+ anti-Lambda K-

Authors: The BABAR Collaboration, J. P. Lees, V. Poireau, V. Tisserand, J. Garra Tico, E. Grauges, M. Martinelli, D. A. Milanes, A. Palano, M. Pappagallo, G. Eigen, B. Stugu, L. Sun, D. N. Brown, L. T. Kerth, Yu. G. Kolomensky, G. Lynch, H. Koch, T. Schroeder, D. J. Asgeirsson, C. Hearty, T. S. Mattison, J. A. McKenna, A. Khan, V. E. Blinov , et al. (363 additional authors not shown)

Abstract: We report the observation of the baryonic B decay B0bar --> Lambda_c^+ anti-Lambda K- with a significance larger than 7 standard deviations based on 471x10^6$ BBbar pairs collected with the BABAR detector at the PEP-II storage ring at SLAC. We measure the branching fraction for the decay B0bar --> Lambda_c^+ anti-Lambda K- to be (3.8 \pm 0.8_{stat} \pm 0.2_{sys} \pm 1.0_{Lambda_c^+})x10^{-5}. The… ▽ More We report the observation of the baryonic B decay B0bar --> Lambda_c^+ anti-Lambda K- with a significance larger than 7 standard deviations based on 471x10^6$ BBbar pairs collected with the BABAR detector at the PEP-II storage ring at SLAC. We measure the branching fraction for the decay B0bar --> Lambda_c^+ anti-Lambda K- to be (3.8 \pm 0.8_{stat} \pm 0.2_{sys} \pm 1.0_{Lambda_c^+})x10^{-5}. The uncertainties are statistical, systematic, and due to the uncertainty in the Lambda_c^+ branching fraction. We find that the Lambda_c^+ K^- invariant mass distribution shows an enhancement above 3.5 GeV/c^2. △ Less

Submitted 16 August, 2011; originally announced August 2011.

Comments: 7 pages, 7 figures, submitted to Phys. Rev. D (Rapid Communications)