-
Development of RFSoC-based direct sampling highly multiplexed microwave SQUID readout for future CMB and submillimeter surveys
Authors:
Chao Liu,
Zeeshan Ahmed,
Shawn W. Henderson,
Ryan Herbst,
Larry Ruckman,
Thomas Satterthwaite
Abstract:
The SLAC Microresonator Radio Frequency (SMuRF) electronics is being deployed as the readout for the Cosmic Microwave Background (CMB) telescopes of the Simons Observatory (SO). A Radio Frequency System-on-Chip (RFSoC) based readout of microwave frequency resonator based cryogenic sensors is under development at SLAC as an upgrade path for SMuRF with simplified RF hardware, a more compact footprin…
▽ More
The SLAC Microresonator Radio Frequency (SMuRF) electronics is being deployed as the readout for the Cosmic Microwave Background (CMB) telescopes of the Simons Observatory (SO). A Radio Frequency System-on-Chip (RFSoC) based readout of microwave frequency resonator based cryogenic sensors is under development at SLAC as an upgrade path for SMuRF with simplified RF hardware, a more compact footprint, and lower total power consumption. The high-speed integrated data converters and digital data path in RFSoC enable direct RF sampling without analog up and down conversion for RF frequencies up to 6 GHz. A comprehensive optimization and characterization study has been performed for direct RF sampling for microwave SQUID multiplexers, which covers noise level, RF dynamic range, and linearity using a prototype implementation. The SMuRF firmware, including the implementation of closed-loop tone tracking, has been ported to the RFSoC platform and interfaced with the quadrature mixers for digital up and down conversion in the data converter data path to realize a full microwave SQUID multiplexer readout. In this paper, a selection of the performance characterization results of direct RF sampling for microwave SQUID multiplexer readout will be summarized and compared with science-driven requirements. Preliminary results demonstrating the read out of cryogenic sensors using the prototype system will also be presented here. We anticipate our new RFSoC-based SMuRF system will be an enabling readout for on-going and future experiments in astronomy and cosmology, which rely on large arrays of cryogenic sensors to achieve their science goals.
△ Less
Submitted 18 June, 2024;
originally announced June 2024.
-
Direct RF Sampling based LLRF Control System for C-band Linear Accelerator
Authors:
C. Liu,
R. Herbst,
B. Hong,
L. Ruckman,
E. A. Nanni
Abstract:
Low Level RF (LLRF) control systems of linear accelerators (LINACs) are typically implemented with heterodyne based architectures, which have complex analog RF mixers for up and down conversion. The Gen 3 Radio Frequency System-on-Chip (RFSoC) device from AMD Xilinx integrates data converters with maximum RF frequency of 6~GHz. This enables direct RF sampling of C-band LLRF signal typically operat…
▽ More
Low Level RF (LLRF) control systems of linear accelerators (LINACs) are typically implemented with heterodyne based architectures, which have complex analog RF mixers for up and down conversion. The Gen 3 Radio Frequency System-on-Chip (RFSoC) device from AMD Xilinx integrates data converters with maximum RF frequency of 6~GHz. This enables direct RF sampling of C-band LLRF signal typically operated at 5.712 GHz without any analogue mixers, which can significantly simplify the system architecture. The data converters sample RF signals in higher order Nyquist zones and then up or down convert digitally by the integrated data path in RFSoC. The closed-loop feedback control firmware implemented in FPGA integrated in RFSoC can process the base-band signal from the ADC data path and calculate the updated phase and amplitude to be up-mixed by the DAC data path. We have developed a C-band LLRF control RFSoC platform with direct RF sampling, which targets Cool Copper Collider (C3) and other C or S band LINAC research and development projects. In this paper, the architecture of the platform will be described. We have optimized the configuration of the data converter and characterized performance of them with RF pulses. The test results for some of the key performance parameters for the LLRF platform with our custom solid-state amplifier, such as phase and amplitude stability, will be discussed in this paper.
△ Less
Submitted 13 May, 2024;
originally announced May 2024.
-
Embedded FPGA Developments in 130nm and 28nm CMOS for Machine Learning in Particle Detector Readout
Authors:
Julia Gonski,
Aseem Gupta,
Haoyi Jia,
Hyunjoon Kim,
Lorenzo Rota,
Larry Ruckman,
Angelo Dragone,
Ryan Herbst
Abstract:
Embedded field programmable gate array (eFPGA) technology allows the implementation of reconfigurable logic within the design of an application-specific integrated circuit (ASIC). This approach offers the low power and efficiency of an ASIC along with the ease of FPGA configuration, particularly beneficial for the use case of machine learning in the data pipeline of next-generation collider experi…
▽ More
Embedded field programmable gate array (eFPGA) technology allows the implementation of reconfigurable logic within the design of an application-specific integrated circuit (ASIC). This approach offers the low power and efficiency of an ASIC along with the ease of FPGA configuration, particularly beneficial for the use case of machine learning in the data pipeline of next-generation collider experiments. An open-source framework called "FABulous" was used to design eFPGAs using 130 nm and 28 nm CMOS technology nodes, which were subsequently fabricated and verified through testing. The capability of an eFPGA to act as a front-end readout chip was assessed using simulation of high energy particles passing through a silicon pixel sensor. A machine learning-based classifier, designed for reduction of sensor data at the source, was synthesized and configured onto the eFPGA. A successful proof-of-concept was demonstrated through reproduction of the expected algorithm result on the eFPGA with perfect accuracy. Further development of the eFPGA technology and its application to collider detector readout is discussed.
△ Less
Submitted 2 July, 2024; v1 submitted 26 April, 2024;
originally announced April 2024.
-
LLRF System Considerations for a Compact, Commercial C-band Accelerator using the AMD Xilinx RF-SoC
Authors:
J. Einstein-Curtis,
J. Edelen,
B. Gur,
M. Henderson,
G. Khalsa,
M. Kilpatrick,
R. O'Rourke,
R. Augustsson,
A. Diego,
A. Smirnov,
S. Thielk,
B. Hong,
Z. Li,
C. Liu,
J. Merrick,
E. Nanni,
L. Ruckman,
S. Tantawi,
F. Zuo
Abstract:
This work describes the LLRF and control system in use for a novel accelerator structure developed for a compact design operating in C-band developed by SLAC, with collaboration from RadiaBeam and RadiaSoft. This design is a pulsed RF/pulsed beam system that only provides minimal monitoring for control of each two-cavity pair. Available signals include only a forward and reflected signal for each…
▽ More
This work describes the LLRF and control system in use for a novel accelerator structure developed for a compact design operating in C-band developed by SLAC, with collaboration from RadiaBeam and RadiaSoft. This design is a pulsed RF/pulsed beam system that only provides minimal monitoring for control of each two-cavity pair. Available signals include only a forward and reflected signal for each pair; such a design requires careful consideration of calibration and power-on routines, as well an understanding of how to correct for disturbances caused by the entire RF signal chain, including a new SSA, klystron, and distribution system. An AMD ** for larger-volume manufacturing.
This material is based upon work supported by the Defense Advanced Research Projects Agency under Contract Numbers 140D0423C0006 and 140D0423C0007. The views, opinions, and/or findings expressed are those of the author(s) and should not be interpreted as representing the official views or policies of the Department of Defense or the U.S. Government.
△ Less
Submitted 9 October, 2023; v1 submitted 6 October, 2023;
originally announced October 2023.
-
Higher Order Nyquist Zone Sampling with RFSoC Data Converters for Astronomical and High Energy Physics Readout Systems
Authors:
Chao Liu,
Zeeshan Ahmed,
Shawn W. Henderson,
Ryan Herbst,
Larry Ruckman
Abstract:
From generation to generation, the maximum RF frequency and sampling rate of the integrated data converters in RF system-on-chip (RFSoC) family devices from Xilinx increases significantly. With the integrated digital mixers and up and down conversion blocks in the datapaths of the data converters, those RFSoC devices offer the capability for implementing a full readout system of ground and space-b…
▽ More
From generation to generation, the maximum RF frequency and sampling rate of the integrated data converters in RF system-on-chip (RFSoC) family devices from Xilinx increases significantly. With the integrated digital mixers and up and down conversion blocks in the datapaths of the data converters, those RFSoC devices offer the capability for implementing a full readout system of ground and space-based telescopes and detectors across the electromagnetic spectrum within the devices with minimum or no analog mixing circuit. In this paper, we present the characterization results for the the data converters sampling at higher orders of Nyquist zones to extend the frequency range covered for our targeted readout systems of microwave-frequency resonator-based cryogenic detector and multiplexer systems and other astronomical and high-energy physics instrumentation applications, such as, axion search and dark matter detection. The initial evaluation of the data converters operating higher order Nyquist zones covers two-tones and comb of tones tests to address the concerns in the RF inter-modulation distortion, which is the key performance index for our targeted applications. The characterization of the data converters is performed in the bandwidth of 4-6 GHz and results meet our requirements. The settings and operating strategies of the data converters for our targeted applications will be summarised.
△ Less
Submitted 14 September, 2023;
originally announced September 2023.
-
Evaluating Direct RF Sampling Performance for RFSoC-based Radio-frequency Astronomy Receivers
Authors:
Chao Liu,
Larry Ruckman,
Ryan Herbst
Abstract:
As the maximum RF input and output frequencies of the integrated data converters in RFSoC increase, it becomes practical to digitize and synthesize RF signals in the majority of C band directly without analogue up and down mixing circuits. The elimination of the mixer circuits can significantly simplify the architecture of the receivers or readouts for radio astronomy telescopes. For the systems w…
▽ More
As the maximum RF input and output frequencies of the integrated data converters in RFSoC increase, it becomes practical to digitize and synthesize RF signals in the majority of C band directly without analogue up and down mixing circuits. The elimination of the mixer circuits can significantly simplify the architecture of the receivers or readouts for radio astronomy telescopes. For the systems with large bandwidth or high channel counts, direct sampling can dramatically reduce the size and cost of overall system. This paper with focus on summarising part of the preliminary characterization results for direct sampling with RFSoC data converters in higher order Nyquist zones.
△ Less
Submitted 14 September, 2023;
originally announced September 2023.
-
Performance of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector
Authors:
C. Agapopoulou,
L. A. Beresford,
D. E. Boumediene,
L. Castillo García,
S. Conforti,
C. de la Taille,
L. D. Corpe,
M. J. Da Cunha Sargedas de Sousa,
P. Dinaucourt,
A. Falou,
V. Gautam,
D. Gong,
C. Grieco,
S. Grinstein,
S. Guindon,
A. Howard,
O. Kurdysh,
E. Kuwertz,
C. Li,
N. Makovec,
B. Markovic,
G. Martin-Chassal,
R. Mazzini,
C. Milke,
M. Morenas
, et al. (12 additional authors not shown)
Abstract:
This paper presents the design and characterisation of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector, which is planned for the High-Luminosity phase of the LHC. This prototype, called ALTIROC1, consists of a 5$\times$5-pad matrix and contains the analog part of the single-channel readout (preamplifier, discriminator, two TDCs and SRAM). Two preamplifier architectures (t…
▽ More
This paper presents the design and characterisation of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector, which is planned for the High-Luminosity phase of the LHC. This prototype, called ALTIROC1, consists of a 5$\times$5-pad matrix and contains the analog part of the single-channel readout (preamplifier, discriminator, two TDCs and SRAM). Two preamplifier architectures (transimpedance and voltage) were implemented and tested. The ASIC was characterised both alone and as a module when connected to a 5$\times$5-pad array of LGAD sensors. In calibration measurements, the ASIC operating alone was found to satisfy the technical requirements for the project, with similar performances for both preamplifier types. In particular, the jitter was found to be 15$\pm$1~ps (35$\pm$1~ps) for an injected charge of 10~fC (4~fC). A degradation in performance was observed when the ASIC was connected to the LGAD array. This is attributed to digital couplings at the entrance of the preamplifiers. When the ASIC is connected to the LGAD array, the lowest detectable charge increased from 1.5~fC to 3.4~fC. As a consequence, the jitter increased for an injected charge of 4~fC. Despite this increase, ALTIROC1 still satisfies the maximum jitter specification (below 65~ps) for the HGTD project. This coupling issue also affects the time over threshold measurements and the time-walk correction can only be performed with transimpedance preamplifiers. Beam test measurements with a pion beam at CERN were also undertaken to evaluate the performance of the module. The best time resolution obtained using only ALTIROC TDC data was 46.3$\pm$0.7~ps for a restricted time of arrival range where the coupling issue is minimized. The residual time-walk contribution is equal to 23~ps and is the dominant electronic noise contribution to the time resolution at 15~fC.
△ Less
Submitted 25 July, 2023; v1 submitted 15 June, 2023;
originally announced June 2023.
-
Implementation of a framework for deploying AI inference engines in FPGAs
Authors:
Ryan Herbst,
Ryan Coffee,
Nathan Fronk,
Kukhee Kim,
Kuktae Kim,
Larry Ruckman,
J. J. Russell
Abstract:
The LCLS2 Free Electron Laser FEL will generate xray pulses to beamline experiments at up to 1Mhz These experimentals will require new ultrahigh rate UHR detectors that can operate at rates above 100 kHz and generate data throughputs upwards of 1 TBs a data velocity which requires prohibitively large investments in storage infrastructure Machine Learning has demonstrated the potential to digest la…
▽ More
The LCLS2 Free Electron Laser FEL will generate xray pulses to beamline experiments at up to 1Mhz These experimentals will require new ultrahigh rate UHR detectors that can operate at rates above 100 kHz and generate data throughputs upwards of 1 TBs a data velocity which requires prohibitively large investments in storage infrastructure Machine Learning has demonstrated the potential to digest large datasets to extract relevant insights however current implementations show latencies that are too high for realtime data reduction objectives SLAC has endeavored on the creation of a software framework which translates MLs structures for deployment on Field Programmable Gate Arrays FPGAs deployed at the Edge of the data chain close to the instrumentation This framework leverages ** the maximum latency constrained to the needs of the experiment Our framework is designed to ensure the RTL implementation of the network layers supporting full redeployment of weights and biases without requiring resynthesis after training The ability to reduce the precision of the implemented networks through quantization is necessary to optimize the use of both DSP and memory resources in the FPGA We currently have a preliminary version of the toolset and are experimenting with both general purpose example networks and networks being designed for specific LCLS2 experiments.
△ Less
Submitted 30 May, 2023;
originally announced May 2023.
-
SLAC Microresonator RF (SMuRF) Electronics: A tone-tracking readout system for superconducting microwave resonator arrays
Authors:
Cyndia Yu,
Zeeshan Ahmed,
Josef C. Frisch,
Shawn W. Henderson,
Max Silva-Feaver,
Kam Arnold,
David Brown,
Jake Connors,
Ari J. Cukierman,
J. Mitch D'Ewart,
Bradley J. Dober,
John E. Dusatko,
Gunther Haller,
Ryan Herbst,
Gene C. Hilton,
Johannes Hubmayr,
Kent D. Irwin,
Chao-Lin Kuo,
John A. B. Mates,
Larry Ruckman,
Joel Ullom,
Leila Vale,
Daniel D. Van Winkle,
Jesus Vasquez,
Edward Young
Abstract:
We describe the newest generation of the SLAC Microresonator RF (SMuRF) electronics, a warm digital control and readout system for microwave-frequency resonator-based cryogenic detector and multiplexer systems such as microwave SQUID multiplexers ($μ$mux) or microwave kinetic inductance detectors (MKIDs). Ultra-sensitive measurements in particle physics and astronomy increasingly rely on large arr…
▽ More
We describe the newest generation of the SLAC Microresonator RF (SMuRF) electronics, a warm digital control and readout system for microwave-frequency resonator-based cryogenic detector and multiplexer systems such as microwave SQUID multiplexers ($μ$mux) or microwave kinetic inductance detectors (MKIDs). Ultra-sensitive measurements in particle physics and astronomy increasingly rely on large arrays of cryogenic sensors, which in turn necessitate highly multiplexed readout and accompanying room-temperature electronics. Microwave-frequency resonators are a popular tool for cryogenic multiplexing, with the potential to multiplex thousands of detector channels on one readout line. The SMuRF system provides the capability for reading out up to 3328 channels across a 4-8 GHz bandwidth. Notably, the SMuRF system is unique in its implementation of a closed-loop tone-tracking algorithm that minimizes RF power transmitted to the cold amplifier, substantially relaxing system linearity requirements and effective noise from intermodulation products. Here we present a description of the hardware, firmware, and software systems of the SMuRF electronics, comparing achieved performance with science-driven design requirements. We focus in particular on the case of large channel count, low bandwidth applications, but the system has been easily reconfigured for high bandwidth applications. The system described here has been successfully deployed in lab settings and field sites around the world and is baselined for use on upcoming large-scale observatories.
△ Less
Submitted 22 August, 2022;
originally announced August 2022.
-
Smart sensors using artificial intelligence for on-detector electronics and ASICs
Authors:
Gabriella Carini,
Grzegorz Deptuch,
Jennet Dickinson,
Dionisio Doering,
Angelo Dragone,
Farah Fahim,
Philip Harris,
Ryan Herbst,
Christian Herwig,
** Huang,
Soumyajit Mandal,
Cristina Mantilla Suarez,
Allison McCarn Deiana,
Sandeep Miryala,
F. Mitchell Newcomer,
Benjamin Parpillon,
Veljko Radeka,
Dylan Rankin,
Yihui Ren,
Lorenzo Rota,
Larry Ruckman,
Nhan Tran
Abstract:
Cutting edge detectors push sensing technology by further improving spatial and temporal resolution, increasing detector area and volume, and generally reducing backgrounds and noise. This has led to a explosion of more and more data being generated in next-generation experiments. Therefore, the need for near-sensor, at the data source, processing with more powerful algorithms is becoming increasi…
▽ More
Cutting edge detectors push sensing technology by further improving spatial and temporal resolution, increasing detector area and volume, and generally reducing backgrounds and noise. This has led to a explosion of more and more data being generated in next-generation experiments. Therefore, the need for near-sensor, at the data source, processing with more powerful algorithms is becoming increasingly important to more efficiently capture the right experimental data, reduce downstream system complexity, and enable faster and lower-power feedback loops. In this paper, we discuss the motivations and potential applications for on-detector AI. Furthermore, the unique requirements of particle physics can uniquely drive the development of novel AI hardware and design tools. We describe existing modern work for particle physics in this area. Finally, we outline a number of areas of opportunity where we can advance machine learning techniques, codesign workflows, and future microelectronics technologies which will accelerate design, performance, and implementations for next generation experiments.
△ Less
Submitted 27 April, 2022;
originally announced April 2022.
-
100 Gb/s High Throughput Serial Protocol (HTSP) for Data Acquisition Systems with Interleaved Streaming
Authors:
L. Ruckman,
D. Doering
Abstract:
Demands on Field-Programmable Gate Array (FPGA) data transport have been increasing over the years as frame sizes and refresh rates increase. As the bandwidths requirements increase the ability to implement data transport protocol layers using "soft" programmable logic becomes harder and start to require harden IP blocks implementation. To reduce the number of physical links and interconnects, it…
▽ More
Demands on Field-Programmable Gate Array (FPGA) data transport have been increasing over the years as frame sizes and refresh rates increase. As the bandwidths requirements increase the ability to implement data transport protocol layers using "soft" programmable logic becomes harder and start to require harden IP blocks implementation. To reduce the number of physical links and interconnects, it is common for data acquisition systems to require interleaving of streams on the same link (e.g. streaming data and streaming register access). This paper presents a way to leverage existing FPGA harden IP blocks to achieve a robust, low latency 100 Gb/s point-to-point link with minimal programmable logic overhead geared towards the needs of data acquisition systems with interleaved streaming requirements.
△ Less
Submitted 22 June, 2022; v1 submitted 29 March, 2022;
originally announced March 2022.
-
Recent Progress and Next Steps for the MATHUSLA LLP Detector
Authors:
Cristiano Alpigiani,
Juan Carlos Arteaga-Velázquez,
Austin Ball,
Liron Barak,
Jared Barron,
Brian Batell,
James Beacham,
Yan Benhammo,
Benjamin Brau,
Karen Salomé Caballero-Mora,
Paolo Camarri,
Roberto Cardarelli,
John Paul Chou,
Wentao Cui,
David Curtin,
Miriam Diamond,
Keith R. Dienes,
Liam Andrew Dougherty,
William Dougherty,
Marco Drewes,
Sameer Erramilli,
Rouven Essig,
Erez Etzion,
Jared Evans,
Arturo Fernández Téllez
, et al. (71 additional authors not shown)
Abstract:
We report on recent progress and next steps in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC as part of the Snowmass 2021 process. Our understanding of backgrounds has greatly improved, aided by detailed simulation studies, and significant R&D has been performed on designing the scintillator detectors and understanding their performance. The collaboration is…
▽ More
We report on recent progress and next steps in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC as part of the Snowmass 2021 process. Our understanding of backgrounds has greatly improved, aided by detailed simulation studies, and significant R&D has been performed on designing the scintillator detectors and understanding their performance. The collaboration is on track to complete a Technical Design Report, and there are many opportunities for interested new members to contribute towards the goal of designing and constructing MATHUSLA in time for HL-LHC collisions, which would increase the sensitivity to a large variety of highly motivated LLP signals by orders of magnitude.
△ Less
Submitted 30 March, 2023; v1 submitted 15 March, 2022;
originally announced March 2022.
-
A Microwave SQUID Multiplexer Optimized for Bolometric Applications
Authors:
B. Dober,
Z. Ahmed,
K. Arnold,
D. T. Becker,
D. A. Bennett,
J. A. Connors,
A. Cukierman,
J. M. D'Ewart,
S. M. Duff,
J. E. Dusatko,
J. C. Frisch,
J. D. Gard,
S. W. Henderson,
R. Herbst,
G. C. Hilton,
J. Hubmayr,
Y. Li,
J. A. B. Mates,
H. McCarrick,
C. D Reintsema,
M. Silva-Feaver,
L. Ruckman,
J. N. Ullom,
L. R. Vale,
D. D. Van Winkle
, et al. (5 additional authors not shown)
Abstract:
A microwave SQUID multiplexer ($μ$MUX) has been optimized for coupling to large arrays of superconducting transition-edge sensor (TES) bolometers. We present the scalable cryogenic multiplexer chip design in a 1820-channel multiplexer configuration for the 4-8 GHz rf band. The key metrics of yield, sensitivity, and crosstalk are determined through measurements of 455 readout channels, which span 4…
▽ More
A microwave SQUID multiplexer ($μ$MUX) has been optimized for coupling to large arrays of superconducting transition-edge sensor (TES) bolometers. We present the scalable cryogenic multiplexer chip design in a 1820-channel multiplexer configuration for the 4-8 GHz rf band. The key metrics of yield, sensitivity, and crosstalk are determined through measurements of 455 readout channels, which span 4-5 GHz. The median white-noise level is 45 pA/$\sqrt{\textrm{Hz}}$, evaluated at 2 Hz, with a 1/f knee $\leq$ 20 mHz after common-mode subtraction. The white-noise level decreases the sensitivity of a TES bolometer optimized for detection of the cosmic microwave background at 150 GHz by only 3%. The measured crosstalk between any channel pair is $\leq$ 0.3%.
△ Less
Submitted 19 January, 2021; v1 submitted 15 October, 2020;
originally announced October 2020.
-
Upward-Pointing Cosmic-Ray-like Events Observed with ANITA
Authors:
Andres Romero-Wolf,
P. W. Gorham,
J. Nam,
S. Hoover,
P. Allison,
O. Banerjee,
L. Batten,
J. J. Beatty,
K. Belov,
D. Z. Besson,
W. R. Binns,
V. Bugaev,
P. Cao,
C. Chen,
P. Chen,
J. M. Clem,
A. Connolly,
B. Dailey,
C. Deaconu,
L. Cremonesi,
P. F. Dowkontt,
M. A. DuVernois,
R. C. Field,
B. D. Fox,
D. Goldstein
, et al. (51 additional authors not shown)
Abstract:
These proceedings address a recent publication by the ANITA collaboration of four upward- pointing cosmic-ray-like events observed in the first flight of ANITA. Three of these events were consistent with stratospheric cosmic-ray air showers where the axis of propagation does not inter- sect the surface of the Earth. The fourth event was consistent with a primary particle that emerges from the surf…
▽ More
These proceedings address a recent publication by the ANITA collaboration of four upward- pointing cosmic-ray-like events observed in the first flight of ANITA. Three of these events were consistent with stratospheric cosmic-ray air showers where the axis of propagation does not inter- sect the surface of the Earth. The fourth event was consistent with a primary particle that emerges from the surface of the ice suggesting a possible τ-lepton decay as the origin of this event. These proceedings follow-up on the modeling and testing of the hypothesis that this event was of τ neutrino origin.
△ Less
Submitted 30 September, 2018;
originally announced October 2018.
-
Characteristics of Four Upward-pointing Cosmic-ray-like Events Observed with ANITA
Authors:
P. W. Gorham,
J. Nam,
A. Romero-Wolf,
S. Hoover,
P. Allison,
O. Banerjee,
J. J. Beatty,
K. Belov,
D. Z. Besson,
W. R. Binns,
V. Bugaev,
P. Cao,
C. Chen,
P. Chen,
J. M. Clem,
A. Connolly,
B. Dailey,
C. Deaconu,
L. Cremonesi,
P. F. Dowkonnt,
M. A. Duvernois,
R. C. Field,
B. D. Fox,
D. Goldstein,
J. Gordon
, et al. (44 additional authors not shown)
Abstract:
We report on four radio-detected cosmic-ray (CR) or CR-like events observed with the Antarctic Impulsive Transient Antenna (ANITA), a NASA-sponsored long-duration balloon payload. Two of the four were previously identified as stratospheric CR air showers during the ANITA-I flight. A third stratospheric CR was detected during the ANITA-II flight. Here we report on characteristics these three unusua…
▽ More
We report on four radio-detected cosmic-ray (CR) or CR-like events observed with the Antarctic Impulsive Transient Antenna (ANITA), a NASA-sponsored long-duration balloon payload. Two of the four were previously identified as stratospheric CR air showers during the ANITA-I flight. A third stratospheric CR was detected during the ANITA-II flight. Here we report on characteristics these three unusual CR events, which develop nearly horizontally, 20-30~km above the surface of the Earth. In addition, we report on a fourth steeply upward-pointing ANITA-I CR-like radio event which has characteristics consistent with a primary that emerged from the surface of the ice. This suggests a possible $τ$-lepton decay as the origin of this event, but such an interpretation would require significant suppression of the Standard Model $τ$-neutrino cross section.
△ Less
Submitted 29 June, 2016; v1 submitted 16 March, 2016;
originally announced March 2016.
-
Energy and Flux Measurements of Ultra-High Energy Cosmic Rays Observed During the First ANITA Flight
Authors:
H. Schoorlemmer,
K. Belov,
A. Romero-Wolf,
D. García-Fernández,
V. Bugaev,
S. A. Wissel,
P. Allison,
J. Alvarez-Muñiz,
S. W. Barwick,
J. J. Beatty,
D. Z. Besson,
W. R. Binns,
W. R. Carvalho Jr.,
C. Chen,
P. Chen,
J. M. Clem,
A. Connolly,
P. F. Dowkontt,
M. A. DuVernois,
R. C. Field,
D. Goldstein,
P. W. Gorham,
C. Hast,
C. L. Heber,
T. Huege
, et al. (33 additional authors not shown)
Abstract:
The first flight of the Antarctic Impulsive Transient Antenna (ANITA) experiment recorded 16 radio signals that were emitted by cosmic-ray induced air showers. For 14 of these events, this radiation was reflected from the ice. The dominant contribution to the radiation from the deflection of positrons and electrons in the geomagnetic field, which is beamed in the direction of motion of the air sho…
▽ More
The first flight of the Antarctic Impulsive Transient Antenna (ANITA) experiment recorded 16 radio signals that were emitted by cosmic-ray induced air showers. For 14 of these events, this radiation was reflected from the ice. The dominant contribution to the radiation from the deflection of positrons and electrons in the geomagnetic field, which is beamed in the direction of motion of the air shower. This radiation is reflected from the ice and subsequently detected by the ANITA experiment at a flight altitude of 36km. In this paper, we estimate the energy of the 14 individual events and find that the mean energy of the cosmic-ray sample is 2.9 EeV. By simulating the ANITA flight, we calculate its exposure for ultra-high energy cosmic rays. We estimate for the first time the cosmic-ray flux derived only from radio observations. In addition, we find that the Monte Carlo simulation of the ANITA data set is in agreement with the total number of observed events and with the properties of those events.
△ Less
Submitted 8 February, 2016; v1 submitted 17 June, 2015;
originally announced June 2015.
-
Antarctic Radio Frequency Albedo and Implications for Cosmic Ray Reconstruction
Authors:
D. Z. Besson,
J. Stockham,
M. Sullivan,
P. Allison,
S. W. Barwick,
B. M. Baughman,
J. J. Beatty,
K. Belov,
S. Bevan,
W. R. Binns,
C. Chen,
P. Chen,
J. M. Clem,
A. Connolly,
D. De Marco,
P. F. Dowkontt,
M. DuVernois,
D. Goldstein,
P. W. Gorham,
E. W. Grashorn,
B. Hill,
S. Hoover,
M. Huang,
M. H. Israel,
A. Javaid
, et al. (20 additional authors not shown)
Abstract:
From an elevation of ~38 km, the balloon-borne ANtarctic Impulsive Transient Antenna (ANITA) is designed to detect the up-coming radio frequency (RF) signal resulting from a sub-surface neutrino-nucleon collision. Although no neutrinos have been discovered thus far, ANITA is nevertheless the only experiment to self-trigger on radio frequency emissions from cosmic-ray induced atmospheric air shower…
▽ More
From an elevation of ~38 km, the balloon-borne ANtarctic Impulsive Transient Antenna (ANITA) is designed to detect the up-coming radio frequency (RF) signal resulting from a sub-surface neutrino-nucleon collision. Although no neutrinos have been discovered thus far, ANITA is nevertheless the only experiment to self-trigger on radio frequency emissions from cosmic-ray induced atmospheric air showers. In the majority of those cases, down-coming RF signals are observed via their reflection from the Antarctic ice sheet and back up to the ANITA interferometer. Estimating the energy scale of the incident cosmic rays therefore requires an estimate of the fractional power reflected at the air-ice interface. Similarly, inferring the energy of neutrinos interacting in-ice from observations of the upwards-directed signal refracting out to ANITA also requires consideration of signal coherence across the interface. By comparing the direct Solar RF signal intensity measured with ANITA to the surface-reflected Solar signal intensity, as a function of incident elevation angle relative to the surface Θ, we estimate the power reflection coefficients R(Θ). We find general consistency between our average measurements and the values of R(Θ) expected from the Fresnel equations, separately for horizontal- vs. vertical-polarizations.
△ Less
Submitted 6 October, 2014; v1 submitted 18 January, 2013;
originally announced January 2013.
-
TARGET: A multi-channel digitizer chip for very-high-energy gamma-ray telescopes
Authors:
K. Bechtol,
S. Funk,
A. Okumura,
L. Ruckman,
A. Simons,
H. Tajima,
J. Vandenbroucke,
G. Varner
Abstract:
The next-generation very-high-energy (VHE) gamma-ray observatory, the Cherenkov Telescope Array, will feature dozens of imaging atmospheric Cherenkov telescopes (IACTs), each with thousands of pixels of photo-sensors. To be affordable and reliable, reading out such a mega-channel array requires event recording technology that is highly integrated and modular, with a low cost per channel. We presen…
▽ More
The next-generation very-high-energy (VHE) gamma-ray observatory, the Cherenkov Telescope Array, will feature dozens of imaging atmospheric Cherenkov telescopes (IACTs), each with thousands of pixels of photo-sensors. To be affordable and reliable, reading out such a mega-channel array requires event recording technology that is highly integrated and modular, with a low cost per channel. We present the design and performance of a chip targeted to this application: the TeV Array Readout with GSa/s sampling and Event Trigger (TARGET). This application-specific integrated circuit (ASIC) has 16 parallel input channels, a 4096-sample buffer for each channel, adjustable input termination, self-trigger functionality, and tight window-selected readout. We report the performance of TARGET in terms of sampling frequency, power consumption, dynamic range, current-mode gain, analog bandwidth, and cross talk. The large number of channels per chip allows a low cost per channel ($\10 to $\20 including front-end and back-end electronics but not including photosensors) to be achieved with a TARGET-based IACT readout system. In addition to basic performance parameters of the TARGET chip itself, we present a camera module prototype as well as a second-generation chip (TARGET~2), both of which have been produced.
△ Less
Submitted 28 June, 2012; v1 submitted 9 May, 2011;
originally announced May 2011.
-
The First Limits on the Ultra-high Energy Neutrino Fluence from Gamma-ray Bursts
Authors:
A. G. Vieregg,
K. Palladino,
P. Allison,
B. M. Baughman,
J. J. Beatty,
K. Belov,
D. Z. Besson,
S. Bevan,
W. R. Binns,
C. Chen,
P. Chen,
J. M. Clem,
A. Connolly,
M. Detrixhe,
D. De Marco,
P. F. Dowkontt,
M. DuVernois,
P. W. Gorham,
E. W. Grashorn,
B. Hill,
S. Hoover,
M. Huang,
M. H. Israel,
A. Javaid,
K. M. Liewer
, et al. (12 additional authors not shown)
Abstract:
We set the first limits on the ultra-high energy (UHE) neutrino fluence at energies greater than 10^9 GeV from gamma-ray bursts (GRBs) based on data from the second flight of the ANtarctic Impulsive Transient Antenna (ANITA). During the 31 day flight of ANITA-II, 26 GRBs were recorded by Swift or Fermi. Of these, we analyzed the 12 GRBs which occurred during quiet periods when the payload was away…
▽ More
We set the first limits on the ultra-high energy (UHE) neutrino fluence at energies greater than 10^9 GeV from gamma-ray bursts (GRBs) based on data from the second flight of the ANtarctic Impulsive Transient Antenna (ANITA). During the 31 day flight of ANITA-II, 26 GRBs were recorded by Swift or Fermi. Of these, we analyzed the 12 GRBs which occurred during quiet periods when the payload was away from anthropogenic activity. In a blind analysis, we observe 0 events on a total background of 0.0044 events in the combined prompt window for all 12 low-background bursts. We also observe 0 events from the remaining 14 bursts. We place a 90% confidence level limit on the E^-4 prompt neutrino fluence of 2.5x10^17 GeV^3/cm^2 between 10^8 and 10^12 GeV from GRB090107A. This is the first reported limit on the UHE neutrino fluence from GRBs above 10^9 GeV, and the strongest limit above 10^8 GeV.
△ Less
Submitted 15 February, 2011;
originally announced February 2011.
-
Erratum: Observational Constraints on the Ultra-high Energy Cosmic Neutrino Flux from the Second Flight of the ANITA Experiment
Authors:
P. W. Gorham,
P. Allison,
B. M. Baughman,
J. J. Beatty,
K. Belov,
D. Z. Besson,
S. Bevan,
W. R. Binns,
C. Chen,
P. Chen,
J. M. Clem,
A. Connolly,
M. Detrixhe,
D. De Marco,
P. F. Dowkontt,
M. DuVernois,
E. W. Grashorn,
B. Hill,
S. Hoover,
M. Huang,
M. H. Israel,
A. Javaid,
K. M. Liewer,
S. Matsuno,
B. C. Mercurio
, et al. (13 additional authors not shown)
Abstract:
This is an erratum to our paper in Physical Review D82:022004,2010, corresponding to preprint: arXiv:1003.2961 .
This is an erratum to our paper in Physical Review D82:022004,2010, corresponding to preprint: arXiv:1003.2961 .
△ Less
Submitted 22 November, 2010;
originally announced November 2010.
-
Belle II Technical Design Report
Authors:
T. Abe,
I. Adachi,
K. Adamczyk,
S. Ahn,
H. Aihara,
K. Akai,
M. Aloi,
L. Andricek,
K. Aoki,
Y. Arai,
A. Arefiev,
K. Arinstein,
Y. Arita,
D. M. Asner,
V. Aulchenko,
T. Aushev,
T. Aziz,
A. M. Bakich,
V. Balagura,
Y. Ban,
E. Barberio,
T. Barvich,
K. Belous,
T. Bergauer,
V. Bhardwaj
, et al. (387 additional authors not shown)
Abstract:
The Belle detector at the KEKB electron-positron collider has collected almost 1 billion Y(4S) events in its decade of operation. Super-KEKB, an upgrade of KEKB is under construction, to increase the luminosity by two orders of magnitude during a three-year shutdown, with an ultimate goal of 8E35 /cm^2 /s luminosity. To exploit the increased luminosity, an upgrade of the Belle detector has been pr…
▽ More
The Belle detector at the KEKB electron-positron collider has collected almost 1 billion Y(4S) events in its decade of operation. Super-KEKB, an upgrade of KEKB is under construction, to increase the luminosity by two orders of magnitude during a three-year shutdown, with an ultimate goal of 8E35 /cm^2 /s luminosity. To exploit the increased luminosity, an upgrade of the Belle detector has been proposed. A new international collaboration Belle-II, is being formed. The Technical Design Report presents physics motivation, basic methods of the accelerator upgrade, as well as key improvements of the detector.
△ Less
Submitted 1 November, 2010;
originally announced November 2010.
-
IceCube's In-Ice Radio Extension: Status and Results
Authors:
H. Landsman,
E. Cheng,
E. Kulcyk,
A. W. Laundrie,
B. Rotter,
L. Ruckman,
P. W. Sandstrom,
G. S. Varner
Abstract:
In 2006-2010, several Radio Frequency (RF) detectors and calibration equipment were deployed as part of the IceCube array at depths between 5 to 1400 meters in preparation for a future large scale GZK neutrino detector. IceCube's deep holes and well-established data handling system provide a unique opportunity for deep-ice RF detection studies at the South-Pole. We will present verification and ca…
▽ More
In 2006-2010, several Radio Frequency (RF) detectors and calibration equipment were deployed as part of the IceCube array at depths between 5 to 1400 meters in preparation for a future large scale GZK neutrino detector. IceCube's deep holes and well-established data handling system provide a unique opportunity for deep-ice RF detection studies at the South-Pole. We will present verification and calibration results as well as a status-review of ongoing analyses such as ice-properties, RF noise and reconstruction algorithms.
△ Less
Submitted 19 October, 2010;
originally announced October 2010.
-
Ultra-Relativistic Magnetic Monopole Search with the ANITA-II Balloon-borne Radio Interferometer
Authors:
M. Detrixhe,
D. Besson,
P. W. Gorham,
P. Allison,
B. Baughmann,
J. J. Beatty,
K. Belov,
S. Bevan,
W. R. Binns,
C. Chen,
P. Chen,
J. M. Clem,
A. Connolly,
D. DeMarco,
P. F. Dowkontt,
M. A. Duvernois,
C. Frankenfeld,
E. W. Grashorn,
D. P. Hogan,
N. Griffith,
B. Hill,
S. Hoover,
M. H. Israel,
A. Javaid,
K. M. Liewer
, et al. (14 additional authors not shown)
Abstract:
We have conducted a search for extended energy deposition trails left by ultra-relativistic magnetic monopoles interacting in Antarctic ice. The non-observation of any satisfactory candidates in the 31 days of accumulated ANITA-II flight data results in an upper limit on the diffuse flux of relativistic monopoles. We obtain a 90% C.L. limit of order 10^{-19}/(cm^2-s-sr) for values of Lorentz boost…
▽ More
We have conducted a search for extended energy deposition trails left by ultra-relativistic magnetic monopoles interacting in Antarctic ice. The non-observation of any satisfactory candidates in the 31 days of accumulated ANITA-II flight data results in an upper limit on the diffuse flux of relativistic monopoles. We obtain a 90% C.L. limit of order 10^{-19}/(cm^2-s-sr) for values of Lorentz boost factor 10^{10}<gamma at the anticipated energy E=10^{16} GeV. This bound is stronger than all previously published experimental limits for this kinematic range.
△ Less
Submitted 11 January, 2011; v1 submitted 6 August, 2010;
originally announced August 2010.
-
Observation of Ultra-high-energy Cosmic Rays with the ANITA Balloon-borne Radio Interferometer
Authors:
S. Hoover,
J. Nam,
P. W. Gorham,
E. Grashorn,
P. Allison,
S. W. Barwick,
J. J. Beatty,
K. Belov,
D. Z. Besson,
W. R. Binns,
C. Chen,
P. Chen,
J. M. Clem,
A. Connolly,
P. F. Dowkontt,
M. A. DuVernois,
R. C. Field,
D. Goldstein,
A. G. Vieregg,
C. Hast,
C. L. Hebert,
M. H. Israel,
A. Javaid,
J. Kowalski,
J. G. Learned
, et al. (20 additional authors not shown)
Abstract:
We report the observation of sixteen cosmic ray events of mean energy of 1.5 x 10^{19} eV, via radio pulses originating from the interaction of the cosmic ray air shower with the Antarctic geomagnetic field, a process known as geosynchrotron emission. We present the first ultra-wideband, far-field measurements of the radio spectral density of geosynchrotron emission in the range from 300-1000 MHz.…
▽ More
We report the observation of sixteen cosmic ray events of mean energy of 1.5 x 10^{19} eV, via radio pulses originating from the interaction of the cosmic ray air shower with the Antarctic geomagnetic field, a process known as geosynchrotron emission. We present the first ultra-wideband, far-field measurements of the radio spectral density of geosynchrotron emission in the range from 300-1000 MHz. The emission is 100% linearly polarized in the plane perpendicular to the projected geomagnetic field. Fourteen of our observed events are seen to have a phase-inversion due to reflection of the radio beam off the ice surface, and two additional events are seen directly from above the horizon.
△ Less
Submitted 11 May, 2010; v1 submitted 30 April, 2010;
originally announced May 2010.
-
Observational Constraints on the Ultra-high Energy Cosmic Neutrino Flux from the Second Flight of the ANITA Experiment
Authors:
The ANITA Collaboration,
P. W. Gorham,
P. Allison,
B. M. Baughman,
J. J. Beatty,
K. Belov,
D. Z. Besson,
S. Bevan,
W. R. Binns,
C. Chen,
P. Chen,
J. M. Clem,
A. Connolly,
M. Detrixhe,
D. De Marco,
P. F. Dowkontt,
M. DuVernois,
E. W. Grashorn,
B. Hill,
S. Hoover,
M. Huang,
M. H. Israel,
A. Javaid,
K. M. Liewer,
S. Matsuno
, et al. (13 additional authors not shown)
Abstract:
The Antarctic Impulsive Transient Antenna (ANITA) completed its second long-duration balloon flight in January 2009, with 31 days aloft (28.5 live days) over Antarctica. ANITA searches for impulsive coherent radio Cherenkov emission from 200 to 1200 MHz, arising from the Askaryan charge excess in ultra-high energy neutrino-induced cascades within Antarctic ice. This flight included significant imp…
▽ More
The Antarctic Impulsive Transient Antenna (ANITA) completed its second long-duration balloon flight in January 2009, with 31 days aloft (28.5 live days) over Antarctica. ANITA searches for impulsive coherent radio Cherenkov emission from 200 to 1200 MHz, arising from the Askaryan charge excess in ultra-high energy neutrino-induced cascades within Antarctic ice. This flight included significant improvements over the first flight in the payload sensitivity, efficiency, and a flight trajectory over deeper ice. Analysis of in-flight calibration pulses from surface and sub-surface locations verifies the expected sensitivity. In a blind analysis, we find 2 surviving events on a background, mostly anthropogenic, of 0.97+-0.42 events. We set the strongest limit to date for 1-1000 EeV cosmic neutrinos, excluding several current cosmogenic neutrino models.
△ Less
Submitted 18 May, 2010; v1 submitted 15 March, 2010;
originally announced March 2010.
-
An imaging time-of-propagation system for charged particle identification at a super B factory
Authors:
K. Nishimura,
T. Browder,
H. Hoedlmoser,
B. Jacobson,
J. Kennedy,
M. Rosen,
L. Ruckman,
G. Varner,
A. Wong,
W. Yen
Abstract:
Super B factories that will further probe the flavor sector of the Standard Model and physics beyond will demand excellent charged particle identification (PID), particularly K/pi separation, for momenta up to 4 GeV/c, as well as the ability to operate under beam backgrounds significantly higher than current B factory experiments. We describe an Imaging Time-of-Propagation (iTOP) detector which…
▽ More
Super B factories that will further probe the flavor sector of the Standard Model and physics beyond will demand excellent charged particle identification (PID), particularly K/pi separation, for momenta up to 4 GeV/c, as well as the ability to operate under beam backgrounds significantly higher than current B factory experiments. We describe an Imaging Time-of-Propagation (iTOP) detector which shows significant potential to meet these requirements. Photons emitted from charged particle interactions in a Cerenkov radiator bar are internally reflected to the end of the bar, where they are collected on a compact image plane using photodetectors with fine spatial segmentation in two dimensions. Precision measurements of photon arrival time are used to enhance the two dimensional imaging, allowing the system to provide excellent PID capabilities within a reduced detector envelope. Results of the ongoing optimization of the geometric and physical properties of such a detector are presented, as well as simulated PID performance. Validation of simulations is being performed using a prototype in a cosmic ray test stand at the University of Hawaii.
△ Less
Submitted 3 September, 2009;
originally announced September 2009.
-
IceRay: An IceCube-centered Radio-Cherenkov GZK Neutrino Detector
Authors:
P. Allison,
J. Beatty,
P. Chen,
A. Connolly,
M. DuVernois,
P. Gorham,
F. Halzen,
K. Hanson,
K. Hoffman,
A. Karle,
J. L. Kelley,
H. Landsman,
J. Learned,
C. Miki,
R. Morse,
R. Nichol,
C. Rott,
L. Ruckman,
D. Seckel,
G. Varner,
D. Williams
Abstract:
We discuss design considerations and simulation results for IceRay, a proposed large-scale ultra-high energy (UHE) neutrino detector at the South Pole. The array is designed to detect the coherent Askaryan radio emission from UHE neutrino interactions in the ice, with the goal of detecting the cosmogenic neutrino flux with reasonable event rates. Operating in coincidence with the IceCube neutrin…
▽ More
We discuss design considerations and simulation results for IceRay, a proposed large-scale ultra-high energy (UHE) neutrino detector at the South Pole. The array is designed to detect the coherent Askaryan radio emission from UHE neutrino interactions in the ice, with the goal of detecting the cosmogenic neutrino flux with reasonable event rates. Operating in coincidence with the IceCube neutrino detector would allow complete calorimetry of a subset of the events. We also report on the status of a testbed IceRay station which incorporates both ANITA and IceCube technology and will provide year-round monitoring of the radio environment at the South Pole.
△ Less
Submitted 8 April, 2009;
originally announced April 2009.
-
New Limits on the Ultra-high Energy Cosmic Neutrino Flux from the ANITA Experiment
Authors:
ANITA collaboration,
P. Gorham,
P. Allison,
S. Barwick,
J. Beatty,
D. Besson,
W. Binns,
C. Chen,
P. Chen,
J. Clem,
A. Connolly,
P. Dowkontt,
M. DuVernois,
R. Field,
D. Goldstein,
A. Goodhue,
C. Hast,
C. Hebert,
S. Hoover,
M. Israel,
J. Kowalski,
J. Learned,
K. Liewer,
J. Link,
E. Lusczek
, et al. (18 additional authors not shown)
Abstract:
We report initial results of the first flight of the Antarctic Impulsive Transient Antenna (ANITA-1) 2006-2007 Long Duration Balloon flight, which searched for evidence of a diffuse flux of cosmic neutrinos above energies of 3 EeV. ANITA-1 flew for 35 days looking for radio impulses due to the Askaryan effect in neutrino-induced electromagnetic showers within the Antarctic ice sheets. We report…
▽ More
We report initial results of the first flight of the Antarctic Impulsive Transient Antenna (ANITA-1) 2006-2007 Long Duration Balloon flight, which searched for evidence of a diffuse flux of cosmic neutrinos above energies of 3 EeV. ANITA-1 flew for 35 days looking for radio impulses due to the Askaryan effect in neutrino-induced electromagnetic showers within the Antarctic ice sheets. We report here on our initial analysis, which was performed as a blind search of the data. No neutrino candidates are seen, with no detected physics background. We set model-independent limits based on this result. Upper limits derived from our analysis rule out the highest cosmogenic neutrino models. In a background horizontal-polarization channel, we also detect six events consistent with radio impulses from ultra-high energy extensive air showers.
△ Less
Submitted 14 December, 2008;
originally announced December 2008.
-
The Antarctic Impulsive Transient Antenna Ultra-high Energy Neutrino Detector Design, Performance, and Sensitivity for 2006-2007 Balloon Flight
Authors:
ANITA collaboration,
P. Gorham,
P. Allison,
S. Barwick,
J. Beatty,
D. Besson,
W. Binns,
C. Chen,
P. Chen,
J. Clem,
A. Connolly,
P. Dowkontt,
M. DuVernois,
R. Field,
D. Goldstein,
A. Goodhue,
C. Hast,
C. Hebert,
S. Hoover,
M. Israel,
J. Kowalski,
J. Learned,
K. Liewer,
J. Link,
E. Lusczek
, et al. (18 additional authors not shown)
Abstract:
We present a detailed report on the experimental details of the Antarctic Impulsive Transient Antenna (ANITA) long duration balloon payload, including the design philosophy and realization, physics simulations, performance of the instrument during its first Antarctic flight completed in January of 2007, and expectations for the limiting neutrino detection sensitivity. Neutrino physics results wi…
▽ More
We present a detailed report on the experimental details of the Antarctic Impulsive Transient Antenna (ANITA) long duration balloon payload, including the design philosophy and realization, physics simulations, performance of the instrument during its first Antarctic flight completed in January of 2007, and expectations for the limiting neutrino detection sensitivity. Neutrino physics results will be reported separately.
△ Less
Submitted 9 December, 2008;
originally announced December 2008.
-
AURA - A radio frequency extension to IceCube
Authors:
H. Landsman,
L. Ruckman,
G. S. Varner
Abstract:
The excellent radio frequency transparency of cold polar ice, combined with the coherent Cherenkov emission produced by neutrino-induced showers when viewed at wavelengths longer than a few centimeters, has spurred considerable interest in a large-scale radio-wave neutrino detector array.
The AURA (Askaryan Under-ice Radio Array) experimental effort, within the IceCube collaboration, seeks to…
▽ More
The excellent radio frequency transparency of cold polar ice, combined with the coherent Cherenkov emission produced by neutrino-induced showers when viewed at wavelengths longer than a few centimeters, has spurred considerable interest in a large-scale radio-wave neutrino detector array.
The AURA (Askaryan Under-ice Radio Array) experimental effort, within the IceCube collaboration, seeks to take advantage of the opportunity presented by IceCube drilling through 2010 to establish the radio frequency technology needed to achieve 100-1000 km^3 effective volumes.
In the 2006-2007 Austral summer 3 deep in-ice radio frequency (RF) clusters were deployed at depths of 1300m and 300m on top of the IceCube strings. Additional 3 clusters will be deployed in the Austral summer of 2008-2009. Verification and calibration results from the current deployed clusters are presented, and the detector design and performances are discussed. Augmentation of IceCube with large-scale 1000km^3sr radio and acoustic arrays would extend the physics reach of IceCube into the EeV-ZeV regime and offer substantial technological redundancy.
△ Less
Submitted 15 November, 2008;
originally announced November 2008.
-
The PRO1 ASIC for Fast Wilkinson Encoding
Authors:
L. L. Ruckman,
G. S. Varner
Abstract:
Wilkinson conversion of stored samples in large Switch Capacitor Array (SCA) ASICs, such as used for high speed waveform sampling, has many benefits in terms of compactness, no missing output codes, low power requirements and robustness. However such Analog-to-Digital conversions are relatively slow, limited by the encoder clock speed. By repeating the same fast sampling technique used by the SC…
▽ More
Wilkinson conversion of stored samples in large Switch Capacitor Array (SCA) ASICs, such as used for high speed waveform sampling, has many benefits in terms of compactness, no missing output codes, low power requirements and robustness. However such Analog-to-Digital conversions are relatively slow, limited by the encoder clock speed. By repeating the same fast sampling technique used by the SCA, combined with a fast priority encoder, significantly faster conversion is demonstrated for a prototype ASIC designated PRO1. For 8-10 bits of resolution, this technique is compact and requires far fewer system resources.
△ Less
Submitted 4 November, 2008; v1 submitted 3 September, 2008;
originally announced September 2008.
-
High Voltage CMOS Control Interface for Astronomy - Grade Charged Coupled Devices
Authors:
Elena Martin,
Gary Varner,
Aaron Koga,
Larry Ruckman,
Peter Onaka,
John Tonry,
Aaron Lee
Abstract:
The Pan-STARRS telescope consists of an array of smaller mirrors viewed by a Gigapixel arrays of CCDs. These focal planes employ Orthogonal Transfer CCDs (OTCCDs) to allow on-chip image stabilization. Each OTCCD has advanced logic features that are controlled externally. A CMOS Interface Device for High Voltage has been developed to provide the appropiate voltage signal levels from a readout and…
▽ More
The Pan-STARRS telescope consists of an array of smaller mirrors viewed by a Gigapixel arrays of CCDs. These focal planes employ Orthogonal Transfer CCDs (OTCCDs) to allow on-chip image stabilization. Each OTCCD has advanced logic features that are controlled externally. A CMOS Interface Device for High Voltage has been developed to provide the appropiate voltage signal levels from a readout and control system designated STARGRASP. OTCCD chip output levels range from -3.3V to 16.7V, with two different output drive strenghts required depending on load capacitance (50pF and 1000pF), with 24mA of drive and a rise time on the order of 100ns. Additional testing ADC structures have been included in this chip to evaluate future functional additions for a next version of the chip.
△ Less
Submitted 12 August, 2008; v1 submitted 2 June, 2008;
originally announced June 2008.
-
Sub-10ps Monolithic and Low-power Photodetector Readout
Authors:
Gary S. Varner,
Larry L. Ruckman
Abstract:
Recent advances in photon detectors have resulted in high-density imaging arrays that offer many performance and cost advantages. In particular, the excellent transit time spread of certain devices show promise to provide tangible benefits in applications such as Positron Emission Tomography (PET). Meanwhile, high-density, high-performance readout techniques have not kept on pace for exploiting…
▽ More
Recent advances in photon detectors have resulted in high-density imaging arrays that offer many performance and cost advantages. In particular, the excellent transit time spread of certain devices show promise to provide tangible benefits in applications such as Positron Emission Tomography (PET). Meanwhile, high-density, high-performance readout techniques have not kept on pace for exploiting these developments. Photodetector readout for next generation high event rate particle identification and time-resolved PET requires a highly-integrated, low-power, and cost-effective readout technique. We propose fast waveform sampling as a method that meets these criteria and demonstrate that sub-10ps resolution can be obtained for an existing device.
△ Less
Submitted 15 May, 2008;
originally announced May 2008.
-
The first version Buffered Large Analog Bandwidth (BLAB1) ASIC for high luminosity collider and extensive radio neutrino detectors
Authors:
Gary S. Varner,
Larry L. Ruckman,
Andrew Wong
Abstract:
Future detectors for high luminosity particle identification and ultra high energy neutrino observation would benefit from a digitizer capable of recording sensor elements with high analog bandwidth and large record depth, in a cost-effective, compact and low-power way. A first version of the Buffered Large Analog Bandwidth (BLAB1) ASIC has been designed based upon the lessons learned from the d…
▽ More
Future detectors for high luminosity particle identification and ultra high energy neutrino observation would benefit from a digitizer capable of recording sensor elements with high analog bandwidth and large record depth, in a cost-effective, compact and low-power way. A first version of the Buffered Large Analog Bandwidth (BLAB1) ASIC has been designed based upon the lessons learned from the development of the Large Analog Bandwidth Recorder and Digitizer with Ordered Readout (LABRADOR) ASIC. While this LABRADOR ASIC has been very successful and forms the basis of a generation of new, large-scale radio neutrino detectors, its limited sampling depth is a major drawback. A prototype has been designed and fabricated with 65k deep sampling at multi-GSa/s operation. We present test results and directions for future evolution of this sampling technique.
△ Less
Submitted 4 May, 2008; v1 submitted 15 February, 2008;
originally announced February 2008.
-
In situ radioglaciological measurements near Taylor Dome, Antarctica and implications for UHE neutrino astronomy
Authors:
D. Besson,
J. Jenkins,
S. Matsuno,
J. Nam,
M. Smith,
S. W. Barwick,
J. J. Beatty,
W. R. Binns,
C. Chen,
P. Chen,
J. M. Clem,
A. Connolly,
P. F. Dowkontt,
M. A. DuVernois,
R. C. Field,
D. Goldstein,
P. W. Gorham,
A. Goodhue,
C. Hast,
C. L. Hebert,
S. Hoover,
M. H. Israel,
J. Kowalski,
J. G. Learned,
K. M. Liewer
, et al. (18 additional authors not shown)
Abstract:
Radiowave detection of the Cherenkov radiation produced by neutrino-ice collisions requires an understanding of the radiofrequency (RF) response of cold polar ice. We herein report on a series of radioglaciological measurements performed approximately 10 km north of Taylor Dome Station, Antarctica from Dec. 6, 2006 - Dec. 16, 2006. Using RF signals broadcast from: a) an englacial discone, submer…
▽ More
Radiowave detection of the Cherenkov radiation produced by neutrino-ice collisions requires an understanding of the radiofrequency (RF) response of cold polar ice. We herein report on a series of radioglaciological measurements performed approximately 10 km north of Taylor Dome Station, Antarctica from Dec. 6, 2006 - Dec. 16, 2006. Using RF signals broadcast from: a) an englacial discone, submerged to a depth of 100 meters and broadcasting to a surface dual polarization horn receiver, and b) a dual-polarization horn antenna on the surface transmitting signals which reflect off the underlying bed and back up to the surface receiver, we have made time-domain estimates of both the real (index-of-refraction) and imaginary (attenuation length) components of the complex ice dielectric constant. We have also measured the uniformity of ice response along two orthogonal axes in the horizontal plane. We observe a wavespeed asymmetry of order 0.1%, projected onto the vertical propagation axis, consistent with some previous measurements, but somewhat lower than others.
△ Less
Submitted 7 October, 2008; v1 submitted 15 March, 2007;
originally announced March 2007.
-
A Monolithic Time Stretcher for Precision Time Recording
Authors:
Gary S. Varner,
Larry L. Ruckman
Abstract:
Identifying light mesons which contain only up/down quarks (pions) from those containing a strange quark (kaons) over the typical meter length scales of a particle physics detector requires instrumentation capable of measuring flight times with a resolution on the order of 20ps. In the last few years a large number of inexpensive, multi-channel Time-to-Digital Converter (TDC) chips have become a…
▽ More
Identifying light mesons which contain only up/down quarks (pions) from those containing a strange quark (kaons) over the typical meter length scales of a particle physics detector requires instrumentation capable of measuring flight times with a resolution on the order of 20ps. In the last few years a large number of inexpensive, multi-channel Time-to-Digital Converter (TDC) chips have become available. These devices typically have timing resolution performance in the hundreds of ps regime. A technique is presented that is a monolithic version of ``time stretcher'' solution adopted for the Belle Time-Of-Flight system to address this gap between resolution need and intrinsic multi-hit TDC performance.
△ Less
Submitted 6 April, 2007; v1 submitted 23 January, 2007;
originally announced January 2007.
-
The Large Analog Bandwidth Recorder And Digitizer with Ordered Readout (LABRADOR) ASIC
Authors:
G. S. Varner,
L. L. Ruckman,
J. W. Nam,
R. J. Nichol,
J. Cao,
P. W. Gorham,
M. Wilcox
Abstract:
Three generations of full-custom analog integrated circuits designed for low-power, high-speed sampling of Radio-Frequency (RF) transients in excess of the Nyquist minimum have been developed. These 0.25$μm$ CMOS devices are denoted the Large Analog Bandwidth Recorder and Digitizer with Ordered Readout (LABRADOR) ASICs and finally consist of 9 channels of 260 deep sampling. Continuous sampling i…
▽ More
Three generations of full-custom analog integrated circuits designed for low-power, high-speed sampling of Radio-Frequency (RF) transients in excess of the Nyquist minimum have been developed. These 0.25$μm$ CMOS devices are denoted the Large Analog Bandwidth Recorder and Digitizer with Ordered Readout (LABRADOR) ASICs and finally consist of 9 channels of 260 deep sampling. Continuous sampling is provided with common stop capability. Input analog bandwidth is approximately 1GHz and sampling speeds are adjustable from 0.02 to 3.7GSa/s. Completely parallel internal conversion supports 12-bit digitization and readout of all 2340 cells in under 50$μs$.
△ Less
Submitted 14 June, 2007; v1 submitted 2 September, 2005;
originally announced September 2005.