-
Multi-Scale Experimental Characterization for LS-DYNA MAT213 Modeling of Composite Structures under High Strain Rate
Authors:
Jackob Black,
Ryan Premo,
Robert K. Goldberg,
Trenton M. Ricks,
Troy Lyons,
Han-Gyu Kim
Abstract:
Aerospace structures often experience high strain rate events such as ballistic impact, crash, or crush. A material model has been developed that enhances the capability to simulate the dynamic response of composite materials under these loading conditions. The material model has been implemented into the commercially available transient dynamic finite element code LS-DYNA as MAT213. The model can…
▽ More
Aerospace structures often experience high strain rate events such as ballistic impact, crash, or crush. A material model has been developed that enhances the capability to simulate the dynamic response of composite materials under these loading conditions. The material model has been implemented into the commercially available transient dynamic finite element code LS-DYNA as MAT213. The model can simulate the nonlinear deformation, damage, and failure that takes place in a composite under dynamic loading conditions. The specific goal of this work is to characterize the MAT213 input for the representative material. The specific composite material being examined consists of T700G unidirectional carbon fibers and a low-melt PolyArylEtherKetone (LMPAEK) thermoplastic resin system. It is formally referred to as Toray TC1225 LMPAEK T700G. As the initial part of this work, this paper is focused on characterizing the material parameters for the MAT213 deformation model based on results obtained from multi-scale experimentation. The effort concentrated on characterizing the in-plane material response suitable for use with thin shell elements. For shell elements within MAT213, tabulated stress-strain results from tension and compression tests in the longitudinal and transverse directions and in-plane shear tests are required. Due to the difficulty of measuring small strains in the transverse direction, a multi-scale testing method was developed. Macro-scale testing is performed per the typical ASTM methods while micro-scale testing uses a microscope along with smaller coupon sizes to obtain the smaller strains in the transverse direction of each test. For both testing methods, a VIC-2D camera and software for digital image correlation analysis are used. Using the DIC combined with each test fixture, reliable stress and strain data are collected.
△ Less
Submitted 17 March, 2024;
originally announced March 2024.
-
Experimental Characterization of Non-Associative Plasticity Flow Rule Coefficients for the LS-DYNA MAT213 Model
Authors:
Ryan Premo,
Jackob Black,
Michael Pereira,
Robert K. Goldberg,
Trenton M. Ricks,
Han-Gyu Kim
Abstract:
This project is focused on develo** an experimental framework for characterizing non-associative plasticity flow rule coefficients through coupon-scale tests for the LS-DYNA MAT213 model. The main objective is to characterize these coefficients based on the multi-scale (i.e., both microscopic and macroscopic) full-field measurement of the evolution of strain and stress fields. This paper focuses…
▽ More
This project is focused on develo** an experimental framework for characterizing non-associative plasticity flow rule coefficients through coupon-scale tests for the LS-DYNA MAT213 model. The main objective is to characterize these coefficients based on the multi-scale (i.e., both microscopic and macroscopic) full-field measurement of the evolution of strain and stress fields. This paper focuses on presenting the experimental work on characterizing the full-scale stress-strain curves of T700/LM-PAEK composites under tension, compression, and shear loads. The experimental data set was intended to build a deformation sub-model in the MAT213 model for the material. The strain data were collected using both microscopic and macroscopic digital image correlation techniques. The microscopic technique was particularly useful for fracture cases under small strains. A preliminary simulation result obtained from the MAT213 model is also presented in the paper. The experimental framework herein will be extended to characterize post-peak stress degradation in the composite material and to develop a damage sub-model for the material. This project will contribute to develo** a simulation tool based on the MAT213 model for simulating the rate-dependent impact damages in composites under multi-axial loading.
△ Less
Submitted 5 December, 2023;
originally announced December 2023.
-
Phase transition kinetics revealed by in situ X-ray diffraction in laser-heated dynamic diamond anvil cells
Authors:
Matthew Ricks,
Arianna E. Gleason,
Francesca Miozzi,
Hong Yang,
Stella Chariton,
Vitali B. Prakapenka,
Stanislav V. Sinogeikin,
Richard L. Sandberg,
Wendy L. Mao,
Silvia Pandolfi
Abstract:
We report on a novel approach to dynamic compression of materials that bridges the gap between previous static- and dynamic- compression techniques, allowing to explore a wide range of pathways in the pressure-temperature space. By combining a dynamic-diamond anvil cell setup with double-sided laser-heating and in situ X-ray diffraction, we are able to perform dynamic compression at high temperatu…
▽ More
We report on a novel approach to dynamic compression of materials that bridges the gap between previous static- and dynamic- compression techniques, allowing to explore a wide range of pathways in the pressure-temperature space. By combining a dynamic-diamond anvil cell setup with double-sided laser-heating and in situ X-ray diffraction, we are able to perform dynamic compression at high temperature and characterize structural transitions with unprecedented time resolution. Using this method, we investigate the $γ-ε$ phase transition of iron under dynamic compression for the first time, reaching compression rates of hundreds of GPa/s and temperatures of 2000 K. Our results demonstrate a distinct response of the $γ-ε$ and $α-ε$ transitions to the high compression rates achieved. These findings open up new avenues to study tailored dynamic compression pathways in the pressure-temperature space and highlight the potential of this platform to capture kinetic effects in a diamond anvil cell.
△ Less
Submitted 29 January, 2024; v1 submitted 15 March, 2023;
originally announced March 2023.
