-
An extreme thermal cycling reliability test of ATLAS ITk Strips barrel modules
Authors:
A. Tishelman-Charny,
A. Affolder,
F. Capocasa,
E. Duden,
V. Fadeyev,
M. Gignac,
C. Helling,
H. Herde,
J. Johnson,
D. Lynn,
M. Morii,
A. Mitra,
L. Poley,
G. Sciolla,
S. Stucci,
P. Sharma,
G. Van Nieuwenhuizen,
E. Wallin,
A. Wang,
S. Wonsak
Abstract:
At the end of Run 3 of the Large Hadron Collider (LHC), the accelerator complex will be upgraded to the High-Luminosity LHC (HL-LHC) in order to increase the total amount of data provided to its experiments. To cope with the increased rates of data, radiation, and pileup, the ATLAS detector will undergo a substantial upgrade, including a replacement of the Inner Detector with a future Inner Tracke…
▽ More
At the end of Run 3 of the Large Hadron Collider (LHC), the accelerator complex will be upgraded to the High-Luminosity LHC (HL-LHC) in order to increase the total amount of data provided to its experiments. To cope with the increased rates of data, radiation, and pileup, the ATLAS detector will undergo a substantial upgrade, including a replacement of the Inner Detector with a future Inner Tracker, called the ITk. The ITk will be composed of pixel and strip sub-detectors, where the strips portion will be composed of 17,888 silicon strip detector modules. During the HL-LHC running period, the ITk will be cooled and warmed a number of times from about ${-35}^\circ$C to room temperature as part of the operational cycle, including warm-ups during yearly shutdowns. To ensure ITk Strips modules are functional after these expected temperature changes, and to ensure modules are mechanically robust, each module must undergo ten thermal cycles and pass a set of electrical and mechanical criteria before it is placed on a local support structure. This paper describes the thermal cycling Quality Control (QC) procedure, and results from the barrel pre-production phase (about 5% of the production volume). Additionally, in order to assess the headroom of the nominal QC procedure of 10 cycles and to ensure modules don't begin failing soon after, four representative ITk Strips barrel modules were thermally cycled 100 times - this study is also described.
△ Less
Submitted 8 July, 2024;
originally announced July 2024.
-
Threshold bounce -- occupancy-dependent modulation of the discriminating threshold in silicon detectors
Authors:
M. J. Basso,
E. Buchanan,
B. J. Gallop,
J. J. John,
J. Kaplon,
P. T. Keener,
P. W. Phillips,
L. Poley,
C. A. Sawyer,
D. Sperlich,
M. Warren
Abstract:
The front-end electronics of silicon detectors are typically designed to ensure optimal noise performance for the expected input charge. A combination of preamplifiers and shaper circuits result in a nontrivial response of the front-end to injected charge, and the magnitude of the response may be sizeable in readout windows subsequent to that in which the charge was initially injected. The modulat…
▽ More
The front-end electronics of silicon detectors are typically designed to ensure optimal noise performance for the expected input charge. A combination of preamplifiers and shaper circuits result in a nontrivial response of the front-end to injected charge, and the magnitude of the response may be sizeable in readout windows subsequent to that in which the charge was initially injected. The modulation of the discriminator threshold due to the superposition of the front-end response across multiple readout windows is coined "threshold bounce".
In this paper, we report a measurement of threshold bounce using silicon modules built for the Phase-II Upgrade of the ATLAS detector at the Large Hadron Collider. These modules utilize ATLAS Binary Chips for their hit readout. The measurement was performed using a micro-focused 15 keV photon beam at the Diamond Light Source synchrotron. The effect of the choice of photon flux and discriminator threshold on the magnitude of the threshold bounce is studied. A Monte Carlo simulation which accounts for the front-end behaviour of the silicon modules is developed, and its predicted hit efficiency is found to be in good agreement with the measured hit efficiency.
△ Less
Submitted 15 June, 2024;
originally announced June 2024.
-
Characterizing Novel Indium Phosphide Pad Detectors with Focused X-ray Beams and Laboratory Tests
Authors:
Earl Almazan,
Anthony Affolder,
Ian Dyckes,
Vitaliy Fadeyev,
Michael Hance,
Manoj Jadhav,
Sungjoon Kim,
Thomas McCoy,
Jessica Metcalfe,
Jason Nielsen,
Jennifer Ott,
Luise Poley,
Taylor Shin,
Dennis Sperlich,
Anirudha V. Sumant
Abstract:
Future tracking systems in High Energy Physics experiments will require large instrumented areas with low radiation length. Crystalline silicon sensors have been used in tracking systems for decades, but are difficult to manufacture and costly to produce for large areas. We are exploring alternative sensor materials that are amenable to fast fabrication techniques used for thin film devices. Indiu…
▽ More
Future tracking systems in High Energy Physics experiments will require large instrumented areas with low radiation length. Crystalline silicon sensors have been used in tracking systems for decades, but are difficult to manufacture and costly to produce for large areas. We are exploring alternative sensor materials that are amenable to fast fabrication techniques used for thin film devices. Indium Phosphide pad sensors were fabricated at Argonne National Lab using commercially available InP:Fe 2-inch mono-crystal substrates. Current-voltage and capacitance-voltage characterizations were performed to study the basic operating characteristics of a group of sensors. Micro-focused X-ray beams at Canadian Light Source and Diamond Light Source were used to study the response to ionizing radiation, and characterize the uniformity of the response for several devices. The results show a high degree of performance uniformity in our evaluations, both within a device and between the 48 tested devices. This motivates further studies into thin film devices for future tracking detectors.
△ Less
Submitted 10 July, 2024; v1 submitted 29 May, 2024;
originally announced May 2024.
-
Interaction networks in persistent Lotka-Volterra communities
Authors:
Lyle Poley,
Tobias Galla,
Joseph W. Baron
Abstract:
A central concern of community ecology is the interdependence between interaction strengths and the underlying structure of the network upon which species interact. In this work we present a solvable example of such a feedback mechanism in a generalised Lotka-Volterra dynamical system. Beginning with a community of species interacting on a network with arbitrary degree distribution, we provide an…
▽ More
A central concern of community ecology is the interdependence between interaction strengths and the underlying structure of the network upon which species interact. In this work we present a solvable example of such a feedback mechanism in a generalised Lotka-Volterra dynamical system. Beginning with a community of species interacting on a network with arbitrary degree distribution, we provide an analytical framework from which properties of the eventual `surviving community' can be derived. We find that highly-connected species are less likely to survive than their poorly connected counterparts, which skews the eventual degree distribution towards a preponderance of species with low degree, a pattern commonly observed in real ecosystems. Further, the average abundance of the neighbours of a species in the surviving community is lower than the community average (reminiscent of the famed friendship paradox). Finally, we show that correlations emerge between the connectivity of a species and its interactions with its neighbours. More precisely, we find that highly-connected species tend to benefit from their neighbours more than their neighbours benefit from them. These correlations are not present in the initial pool of species and are a result of the dynamics.
△ Less
Submitted 12 April, 2024;
originally announced April 2024.
-
Eigenvalue spectra of finely structured random matrices
Authors:
Lyle Poley,
Tobias Galla,
Joseph W. Baron
Abstract:
Random matrix theory allows for the deduction of stability criteria for complex systems using only a summary knowledge of the statistics of the interactions between components. As such, results like the well-known elliptical law are applicable in a myriad of different contexts. However, it is often assumed that all components of the complex system in question are statistically equivalent, which is…
▽ More
Random matrix theory allows for the deduction of stability criteria for complex systems using only a summary knowledge of the statistics of the interactions between components. As such, results like the well-known elliptical law are applicable in a myriad of different contexts. However, it is often assumed that all components of the complex system in question are statistically equivalent, which is unrealistic in many applications. Here, we introduce the concept of a finely-structured random matrix. These are random matrices with element-specific statistics, which can be used to model systems in which the individual components are statistically distinct. By supposing that the degree of `fine structure' in the matrix is small, we arrive at a succinct `modified' elliptical law. We demonstrate the direct applicability of our results to the niche and cascade models in theoretical ecology, as well as a model of a neural network, and a directed network with arbitrary degree distribution. The simple closed form of our central results allow us to draw broad qualitative conclusions about the effect of fine structure on stability.
△ Less
Submitted 3 November, 2023;
originally announced November 2023.
-
Setups for eliminating static charge of the ATLAS18 strip sensors
Authors:
P. Federicova,
A. Affolder,
G. A. Beck,
A. J. Bevand,
Z. Chen,
I. Dawson,
A. Deshmukh,
A. Dowling,
V. Fadeyev,
J. Fernandez-Tejero,
A. Fournier,
N. Gonzalez,
L. Hommels,
C. Jessiman,
S. Kachiguin,
Ch. Klein,
T. Koffas,
J. Kroll,
V. Latonova,
M. Mikestikova,
P. S. Miyagawa,
S. O'Toole,
Q. Paddock,
L. Poley,
E. Staats
, et al. (5 additional authors not shown)
Abstract:
Construction of the new all-silicon Inner Tracker (ITk), developed by the ATLAS collaboration for the High Luminosity LHC, started in 2020 and is expected to continue till 2028. The ITk detector will include 18,000 highly segmented and radiation hard n+-in-p silicon strip sensors (ATLAS18), which are being manufactured by Hamamatsu Photonics. Mechanical and electrical characteristics of produced s…
▽ More
Construction of the new all-silicon Inner Tracker (ITk), developed by the ATLAS collaboration for the High Luminosity LHC, started in 2020 and is expected to continue till 2028. The ITk detector will include 18,000 highly segmented and radiation hard n+-in-p silicon strip sensors (ATLAS18), which are being manufactured by Hamamatsu Photonics. Mechanical and electrical characteristics of produced sensors are measured upon their delivery at several institutes participating in a complex Quality Control (QC) program. The QC tests performed on each individual sensor check the overall integrity and quality of the sensor. During the QC testing of production ATLAS18 strip sensors, an increased number of sensors that failed the electrical tests was observed. In particular, IV measurements indicated an early breakdown, while large areas containing several tens or hundreds of neighbouring strips with low interstrip isolation were identified by the Full strip tests, and leakage current instabilities were measured in a long-term leakage current stability setup. Moreover, a high surface electrostatic charge reaching a level of several hundreds of volts per inch was measured on a large number of sensors and on the plastic sheets, which mechanically protect these sensors in their paper envelopes. Accumulated data indicates a clear correlation between observed electrical failures and the sensor charge-up. To mitigate the above-described issues, the QC testing sites significantly modified the sensor handling procedures and introduced sensor recovery techniques based on irradiation of the sensor surface with UV light or application of intensive flows of ionized gas. In this presentation, we will describe the setups implemented by the QC testing sites to treat silicon strip sensors affected by static charge and evaluate the effectiveness of these setups in terms of improvement of the sensor performance.
△ Less
Submitted 18 December, 2023; v1 submitted 27 September, 2023;
originally announced September 2023.
-
Generalised Lotka-Volterra model with hierarchical interactions
Authors:
Lyle Poley,
Joseph W. Baron,
Tobias Galla
Abstract:
In the analysis of complex ecosystems it is common to use random interaction coefficients, often assumed to be such that all species are statistically equivalent. In this work we relax this assumption by choosing interactions according to the cascade model, which we incorporate into a generalised Lotka-Volterra dynamical system. These interactions impose a hierarchy in the community. Species benef…
▽ More
In the analysis of complex ecosystems it is common to use random interaction coefficients, often assumed to be such that all species are statistically equivalent. In this work we relax this assumption by choosing interactions according to the cascade model, which we incorporate into a generalised Lotka-Volterra dynamical system. These interactions impose a hierarchy in the community. Species benefit more, on average, from interactions with species further below them in the hierarchy than from interactions with those above. Using dynamic mean-field theory, we demonstrate that a strong hierarchical structure is stabilising, but that it reduces the number of species in the surviving community, as well as their abundances. Additionally, we show that increased heterogeneity in the variances of the interaction coefficients across positions in the hierarchy is destabilising. We also comment on the structure of the surviving community and demonstrate that the abundance and probability of survival of a species is dependent on its position in the hierarchy.
△ Less
Submitted 2 August, 2022;
originally announced August 2022.
-
A Starry Byte -- proton beam measurements of single event upsets and other radiation effects in ABCStar ASIC Versions 0 and 1 for the ITk strip tracker
Authors:
M. J. Basso,
J. Fernandez-Tejero,
B. J. Gallop,
G. Greig,
J. J. John,
P. T. Keener,
K. Krizka,
P. V. Leitao,
B. Norman,
P. W. Phillips,
L. Poley,
C. Sawyer,
T. L. Stack,
S. Stucci,
D. A. Trischuk,
M. Warren
Abstract:
Single Event Effects (SEEs) - predominately bit-flips in electronics caused by particle interactions - are a major concern for ASICs operated in high radiation environments such as ABCStar ASICs, which are designed to be used in the future ATLAS ITk strip tracker. The chip design is therefore optimised to protect it from SEEs by implementing triplication techniques such as Triple Modular Redundanc…
▽ More
Single Event Effects (SEEs) - predominately bit-flips in electronics caused by particle interactions - are a major concern for ASICs operated in high radiation environments such as ABCStar ASICs, which are designed to be used in the future ATLAS ITk strip tracker. The chip design is therefore optimised to protect it from SEEs by implementing triplication techniques such as Triple Modular Redundancy (TMR). In order to verify the radiation protection mechanisms of the chip design, the cross-section for Single Event Upsets (SEUs), a particular class of SEEs, is measured by exposing the chip to high-intensity particle beams while monitoring it for observed SEUs. This study presents the setup, the performed measurements, and the results from SEU tests performed using the latest version of the ABCStar ASIC (ABCStar V1) using a 480 MeV proton beam.
△ Less
Submitted 23 March, 2022;
originally announced March 2022.
-
Map** the material distribution of a complex structure in an electron beam
Authors:
Luise Poley,
Ulf Stolzenberg,
Benjamin Schwenker,
Ariane Frey,
Peter Göttlicher,
Carlos Marinas,
Marcel Stanitzki,
Bernd Stelzer
Abstract:
The simulation and analysis of High Energy Physics experiments require a realistic simulation of the detector material and its distribution. The challenge is to describe all active and passive parts of large scale detectors like ATLAS in terms of their size, position and material composition. The common method for estimating the radiation length by weighing individual components, adding up their c…
▽ More
The simulation and analysis of High Energy Physics experiments require a realistic simulation of the detector material and its distribution. The challenge is to describe all active and passive parts of large scale detectors like ATLAS in terms of their size, position and material composition. The common method for estimating the radiation length by weighing individual components, adding up their contributions and averaging the resulting material distribution over extended structures provides a good general estimate, but can deviate significantly from the material actually present. A method has been developed to assess its material distribution with high spatial resolution using the reconstructed scattering angles and hit positions of high energy electron tracks traversing an object under investigation. The study presented here shows measurements for an extended structure with a highly inhomogeneous material distribution. The structure under investigation is an End-of-Substructure-card prototype designed for the ATLAS Inner Tracker strip tracker -- a PCB populated with components of a large range of material budgets and sizes. The measurements presented here summarise requirements for data samples and reconstructed electron tracks for reliable image reconstruction of large scale, inhomogeneous samples, choices of pixel sizes compared to the size of features under investigation as well as a bremsstrahlung correction for high material densities and thicknesses.
△ Less
Submitted 21 May, 2021;
originally announced May 2021.
-
Map** the in-plane electric field inside irradiated diodes
Authors:
L. Poley,
A. J. Blue,
C. Buttar,
V. Cindro,
C. Darroch,
V. Fadeyev,
J. Fernandez-Tejero,
C. Fleta,
C. Helling,
C. Labitan,
I. Mandić,
S. N. Santpur,
D. Sperlich,
M. Ullán,
Y. Unno
Abstract:
A significant aspect of the Phase-II Upgrade of the ATLAS detector is the replacement of the current Inner Detector with the ATLAS Inner Tracker (ITk). The ATLAS ITk is an all-silicon detector consisting of a pixel tracker and a strip tracker. Sensors for the ITk strip tracker have been developed to withstand the high radiation environment in the ATLAS detector after the High Luminosity Upgrade of…
▽ More
A significant aspect of the Phase-II Upgrade of the ATLAS detector is the replacement of the current Inner Detector with the ATLAS Inner Tracker (ITk). The ATLAS ITk is an all-silicon detector consisting of a pixel tracker and a strip tracker. Sensors for the ITk strip tracker have been developed to withstand the high radiation environment in the ATLAS detector after the High Luminosity Upgrade of the Large Hadron Collider at CERN, which will significantly increase the rate of particle collisions and resulting particle tracks. During their operation in the ATLAS detector, sensors for the ITk strip tracker are expected to accumulate fluences up to 1.6 x 10^15 n_eq/cm^2 (including a safety factor of 1.5), which will significantly affect their performance. One characteristic of interest for highly irradiated sensors is the shape and homogeneity of the electric field inside its active area. For the results presented here, diodes with edge structures similar to full size ATLAS sensors were irradiated up to fluences comparable to those in the ATLAS ITk strip tracker and their electric fields mapped using a micro-focused X-ray beam (beam diameter 2x3 μm^2). This study shows the extension and shape of the electric field inside highly irradiated diodes over a range of applied bias voltages. Additionally, measurements of the outline of the depleted sensor areas allow a comparison of the measured leakage current for different fluences with expectations for the corresponding active areas.
△ Less
Submitted 29 March, 2021;
originally announced March 2021.
-
Measuring the coefficient of moisture expansion of Hysol 9396 loaded with boron nitride powder
Authors:
Luise Poley,
Tim Jones
Abstract:
The future ATLAS ITk strip tracker will consist of 17,000 silicon strip detector modules mounted on support structures called cores. Cores are assembled from a number of components, among others carbon fibre facings, honeycomb structure and carbon foam surrounding titanium tubes used for cooling, using a two-component epoxy (Hysol 9396) loaded with boron nitride for good thermal conductivity. The…
▽ More
The future ATLAS ITk strip tracker will consist of 17,000 silicon strip detector modules mounted on support structures called cores. Cores are assembled from a number of components, among others carbon fibre facings, honeycomb structure and carbon foam surrounding titanium tubes used for cooling, using a two-component epoxy (Hysol 9396) loaded with boron nitride for good thermal conductivity. The adhesive constitutes about 20 % of a core's weight. During operation, the detector is cooled down to -40 $^\circ$C using bi-phase carbon dioxide and flushed with dry gas to prevent condensation. The effect of this temperature change has been simulated to study the impact of Coefficient of Thermal Expansion (CTE) mismatches between different materials and investigate resulting deformations and misalignment. In addition to the shrinking of an adhesive during cooling, which can be estimated well using its known CTE, flushing the detector volume with dry gas removes the moisture contained in the adhesive, leading to an additional shrinking. In order to estimate the impact of shrinking during drying, the Coefficient of Moisture Expansion (CME) of Hysol samples with different contents of boron nitride as well as their overall moisture absorption were measured and their extent compared to the contraction associated with cooling.
△ Less
Submitted 9 March, 2021;
originally announced March 2021.
-
The ABC130 barrel module prototy** programme for the ATLAS strip tracker
Authors:
Luise Poley,
Craig Sawyer,
Sagar Addepalli,
Anthony Affolder,
Bruno Allongue,
Phil Allport,
Eric Anderssen,
Francis Anghinolfi,
Jean-François Arguin,
Jan-Hendrik Arling,
Olivier Arnaez,
Nedaa Alexandra Asbah,
Joe Ashby,
Eleni Myrto Asimakopoulou,
Naim Bora Atlay,
Ludwig Bartsch,
Matthew J. Basso,
James Beacham,
Scott L. Beaupré,
Graham Beck,
Carl Beichert,
Laura Bergsten,
Jose Bernabeu,
Prajita Bhattarai,
Ingo Bloch
, et al. (224 additional authors not shown)
Abstract:
For the Phase-II Upgrade of the ATLAS Detector, its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100 % silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000…
▽ More
For the Phase-II Upgrade of the ATLAS Detector, its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100 % silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototy** programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-25) and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototy** program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests.
△ Less
Submitted 7 September, 2020;
originally announced September 2020.
-
Map** the depleted area of silicon diodes using a micro-focused X-ray beam
Authors:
Luise Poley,
Andrew Blue,
Ingo Bloch,
Craig Buttar,
Vitaliy Fadeyev,
Javier Fernandez-Tejero,
Celeste Fleta,
Johannes Hacker,
Carlos Lacasta Llacer,
Mercedes Miñano,
Martin Renzmann,
Edoardo Rossi,
Craig Sawyer,
Dennis Sperlich,
Martin Stegler,
Miguel Ullán,
Yoshinobu Unno
Abstract:
For the Phase-II Upgrade of the ATLAS detector at CERN, the current ATLAS Inner Detector will be replaced with the ATLAS Inner Tracker. The ATLAS Inner Tracker will be an all-silicon detector, consisting of a pixel tracker and a strip tracker. Sensors for the ITk strip tracker are required to have a low leakage current up to bias voltages of -700 V to maintain a low noise and power dissipation. In…
▽ More
For the Phase-II Upgrade of the ATLAS detector at CERN, the current ATLAS Inner Detector will be replaced with the ATLAS Inner Tracker. The ATLAS Inner Tracker will be an all-silicon detector, consisting of a pixel tracker and a strip tracker. Sensors for the ITk strip tracker are required to have a low leakage current up to bias voltages of -700 V to maintain a low noise and power dissipation. In order to minimise sensor leakage currents, particularly in the high-radiation environment inside the ATLAS detector, sensors are foreseen to be operated at low temperatures and to be manufactured from wafers with a high bulk resistivity of several kΩ cm. Simulations showed the electric field inside sensors with high bulk resistivity to extend towards the sensor edge, which could lead to increased surface currents for narrow dicing edges. In order to map the electric field inside biased silicon sensors with high bulk resistivity, three diodes from ATLAS silicon strip sensor prototype wafers were studied with a monochromatic, micro-focused X-ray beam at the Diamond Light Source. For all devices under investigation, the electric field inside the diode was mapped and its dependence on the applied bias voltage was studied. The findings showed that the electric field in each diode under investigation extended beyond its bias ring and reached the dicing edge.
△ Less
Submitted 27 March, 2019; v1 submitted 7 September, 2018;
originally announced September 2018.
-
Summary and Conclusions of the First DESY Test Beam User Workshop
Authors:
Jan-Hendrik Arling,
M. Sohail Amjad,
Laura Bandiera,
Ties Behnke,
Dominik Dannheim,
Ralf Diener,
Jan Dreyling-Eschweiler,
Heiko Ehrlichmann,
Andreas Gerbershagen,
Ingrid-Maria Gregor,
Avetik Hayrapetyan,
Hendrik Jansen,
Jochen Kaminski,
Jiri Kroll,
Paolo Martinengo,
Norbert Meyners,
Christian Müntz,
Luise Poley,
Benjamin Schwenker,
Marcel Stanitzki
Abstract:
On October 5/6, 2017, DESY hosted the first DESY Test Beam User Workshop [1] which took place in Hamburg. Fifty participants from different user communities, ranging from LHC (ALICE, ATLAS, CMS, LHCb) to FAIR (CBM, PANDA), DUNE, Belle-II, future linear colliders (ILC, CLIC) and generic detector R&D presented their experiences with the DESY II Test Beam Facility, their concrete plans for the upcomi…
▽ More
On October 5/6, 2017, DESY hosted the first DESY Test Beam User Workshop [1] which took place in Hamburg. Fifty participants from different user communities, ranging from LHC (ALICE, ATLAS, CMS, LHCb) to FAIR (CBM, PANDA), DUNE, Belle-II, future linear colliders (ILC, CLIC) and generic detector R&D presented their experiences with the DESY II Test Beam Facility, their concrete plans for the upcoming years and a first estimate of their needs for beam time in the long-term future beyond 2025. A special focus was also on additional improvements to the facility beyond its current capabilities.
△ Less
Submitted 15 May, 2018; v1 submitted 1 February, 2018;
originally announced February 2018.
-
Prototy** of petalets for the Phase-II Upgrade of the silicon strip tracking detector of the ATLAS Experiment
Authors:
S. Kuehn,
V. Benítez,
J. Fernández-Tejero,
C. Fleta,
M. Lozano,
M. Ullán,
H. Lacker,
L. Rehnisch,
D. Sperlich,
D. Ariza,
I. Bloch,
S. Díez,
I. Gregor,
J. Keller,
K. Lohwasser,
L. Poley,
V. Prahl,
N. Zakharchuk,
M. Hauser,
K. Jakobs,
K. Mahboubi,
R. Mori,
U. Parzefall,
J. Bernabéu,
C. Lacasta
, et al. (9 additional authors not shown)
Abstract:
In the high luminosity era of the Large Hadron Collider, the HL-LHC, the instantaneous luminosity is expected to reach unprecedented values, resulting in about 200 proton-proton interactions in a typical bunch crossing. To cope with the resultant increase in occupancy, bandwidth and radiation damage, the ATLAS Inner Detector will be replaced by an all-silicon system, the Inner Tracker (ITk). The I…
▽ More
In the high luminosity era of the Large Hadron Collider, the HL-LHC, the instantaneous luminosity is expected to reach unprecedented values, resulting in about 200 proton-proton interactions in a typical bunch crossing. To cope with the resultant increase in occupancy, bandwidth and radiation damage, the ATLAS Inner Detector will be replaced by an all-silicon system, the Inner Tracker (ITk). The ITk consists of a silicon pixel and a strip detector and exploits the concept of modularity. Prototy** and testing of various strip detector components has been carried out. This paper presents the developments and results obtained with reduced-size structures equivalent to those foreseen to be used in the forward region of the silicon strip detector. Referred to as petalets, these structures are built around a composite sandwich with embedded cooling pipes and electrical tapes for routing the signals and power. Detector modules built using electronic flex boards and silicon strip sensors are glued on both the front and back side surfaces of the carbon structure. Details are given on the assembly, testing and evaluation of several petalets. Measurement results of both mechanical and electrical quantities are shown. Moreover, an outlook is given for improved prototy** plans for large structures.
△ Less
Submitted 5 November, 2017;
originally announced November 2017.
-
Investigations into the impact of locally modified sensor architectures on the detection efficiency of silicon micro-strip sensors
Authors:
Luise Poley,
Kristin Lohwasser,
Andrew Blue,
Mathieu Benoit,
Ingo Bloch,
Sergio Diez,
Vitaliy Fadeyev,
Bruce Gallop,
Ashley Greenall,
Ingrid-Maria Gregor,
John Keller,
Carlos Lacasta,
Dzmitry Maneuski,
Lingxin Meng,
Marko Milovanovic,
Ian Pape,
Peter W. Phillips,
Laura Rehnisch,
Kawal Sawhney,
Craig Sawyer,
Dennis Sperlich,
Martin Stegler,
Yoshinobu Unno,
Matt Warren,
Eda Yildirim
Abstract:
The High Luminosity Upgrade of the LHC will require the replacement of the Inner Detector of ATLAS with the Inner Tracker (ITk) in order to cope with higher radiation levels and higher track densities. Prototype silicon strip detector modules are currently developed and their performance is studied in both particle test beams and X-ray beams. In previous test beam studies of prototype modules, sil…
▽ More
The High Luminosity Upgrade of the LHC will require the replacement of the Inner Detector of ATLAS with the Inner Tracker (ITk) in order to cope with higher radiation levels and higher track densities. Prototype silicon strip detector modules are currently developed and their performance is studied in both particle test beams and X-ray beams. In previous test beam studies of prototype modules, silicon sensor strips were found to respond in regions varying from the strip pitch of 74.5 {\upmu}m. The variations have been linked to local features of the sensor architecture. This paper presents results of detailed sensor measurements in both X-ray and particle beams investigating the impact of sensor features (metal pads and p-stops) on the responding area of a sensor strip.
△ Less
Submitted 3 July, 2017; v1 submitted 18 November, 2016;
originally announced November 2016.
-
Enabling Technologies for Silicon Microstrip Tracking Detectors at the HL-LHC
Authors:
C. Barth,
C. A. Betancourt,
I. Bloch,
F. Bögelspacher,
W. de Boer,
M. Daniels,
A. Dierlamm,
R. Eber,
G. Eckerlin,
D. Eckstein,
T. Eichhorn,
J. Erfle,
L. Feld,
E. Garutti,
I. -M. Gregor,
M. Guthoff,
F. Hartmann,
M. Hauser,
U. Husemann,
K. Jakobs,
A. Junkes,
W. Karpinski,
K. Klein,
S. Kuehn,
H. Lacker
, et al. (16 additional authors not shown)
Abstract:
While the tracking detectors of the ATLAS and CMS experiments have shown excellent performance in Run 1 of LHC data taking, and are expected to continue to do so during LHC operation at design luminosity, both experiments will have to exchange their tracking systems when the LHC is upgraded to the high-luminosity LHC (HL-LHC) around the year 2024. The new tracking systems need to operate in an env…
▽ More
While the tracking detectors of the ATLAS and CMS experiments have shown excellent performance in Run 1 of LHC data taking, and are expected to continue to do so during LHC operation at design luminosity, both experiments will have to exchange their tracking systems when the LHC is upgraded to the high-luminosity LHC (HL-LHC) around the year 2024. The new tracking systems need to operate in an environment in which both the hit densities and the radiation damage will be about an order of magnitude higher than today. In addition, the new trackers need to contribute to the first level trigger in order to maintain a high data-taking efficiency for the interesting processes. Novel detector technologies have to be developed to meet these very challenging goals. The German groups active in the upgrades of the ATLAS and CMS tracking systems have formed a collaborative "Project on Enabling Technologies for Silicon Microstrip Tracking Detectors at the HL-LHC" (PETTL), which was supported by the Helmholtz Alliance "Physics at the Terascale" during the years 2013 and 2014. The aim of the project was to share experience and to work together on key areas of mutual interest during the R&D phase of these upgrades. The project concentrated on five areas, namely exchange of experience, radiation hardness of silicon sensors, low mass system design, automated precision assembly procedures, and irradiations. This report summarizes the main achievements.
△ Less
Submitted 28 April, 2016;
originally announced April 2016.
-
Characterisation of silicon microstrip detectors for the ATLAS Phase-II Upgrade with a micro-focused X-ray beam
Authors:
Luise Poley,
Andrew Blue,
Richard Bates,
Ingo Bloch,
Sergio Diez,
Javier Fernandez-Tejero,
Celeste Fleta,
Bruce Gallop,
Ashley Greenall,
Ingrid-Maria Gregor,
Kazuhiko Hara,
Yoichi Ikegami,
Carlos Lacasta,
Kristin Lohwasser,
Dzmitry Maneuski,
Sebastian Nagorski,
Ian Pape,
Peter W. Phillips,
Dennis Sperlich,
Kawal Sawhney,
Urmila Soldevila,
Miguel Ullan,
Yoshinobu Unno,
Matt Warren
Abstract:
The planned HL-LHC (High Luminosity LHC) in 2025 is being designed to maximise the physics potential through a sizable increase in the luminosity up to 6*10^34 cm^-2 s^-1. A consequence of this increased luminosity is the expected radiation damage at 3000 fb^-1 after ten years of operation, requiring the tracking detectors to withstand fluences to over 1*10^16 1 MeV n_eq/cm^2 . In order to cope wi…
▽ More
The planned HL-LHC (High Luminosity LHC) in 2025 is being designed to maximise the physics potential through a sizable increase in the luminosity up to 6*10^34 cm^-2 s^-1. A consequence of this increased luminosity is the expected radiation damage at 3000 fb^-1 after ten years of operation, requiring the tracking detectors to withstand fluences to over 1*10^16 1 MeV n_eq/cm^2 . In order to cope with the consequent increased readout rates, a complete re-design of the current ATLAS Inner Detector (ID) is being developed as the Inner Tracker (ITk). Two proposed detectors for the ATLAS strip tracker region of the ITk were characterized at the Diamond Light Source with a 3 um FWHM 15 keV micro focused X-ray beam. The devices under test were a 320 Um thick silicon stereo (Barrel) ATLAS12 strip mini sensor wire bonded to a 130 nm CMOS binary readout chip (ABC130) and a 320 Um thick full size radial (end-cap) strip sensor - utilizing bi-metal readout layers - wire bonded to 250 nm CMOS binary readout chips (ABCN-25). A resolution better than the inter strip pitch of the 74.5 um strips was achieved for both detectors. The effect of the p-stop diffusion layers between strips was investigated in detail for the wire bond pad regions. Inter strip charge collection measurements indicate that the effective width of the strip on the silicon sensors is determined by p-stop regions between the strips rather than the strip pitch.
△ Less
Submitted 1 July, 2016; v1 submitted 15 March, 2016;
originally announced March 2016.
-
Alternative glues for the production of ATLAS silicon strip modules for the Phase-II upgrade of the ATLAS Inner Detector
Authors:
Luise Poley,
Ingo Bloch,
Sam Edwards,
Conrad Friedrich,
Ingrid-Maria Gregor,
Tim Jones,
Heiko Lacker,
Simon Pyatt,
Laura Rehnisch,
Dennis Sperlich,
John Wilson
Abstract:
The Phase-II upgrade of the ATLAS detector for the High Luminosity Large Hadron Collider (HL-LHC) includes the replacement of the current Inner Detector with an all-silicon tracker consisting of pixel and strip detectors. The current Phase-II detector layout requires the construction of 20,000 strip detector modules consisting of sensor, circuit boards and readout chips, which are connected mechan…
▽ More
The Phase-II upgrade of the ATLAS detector for the High Luminosity Large Hadron Collider (HL-LHC) includes the replacement of the current Inner Detector with an all-silicon tracker consisting of pixel and strip detectors. The current Phase-II detector layout requires the construction of 20,000 strip detector modules consisting of sensor, circuit boards and readout chips, which are connected mechanically using adhesives. The adhesive between readout chips and circuit board is a silver epoxy glue as was used in the current ATLAS SemiConductor Tracker (SCT). This glue has several disadvantages, which motivated the search for an alternative.
This paper presents a study concerning the use of six ultra-violet (UV) cure glues and a glue pad for use in the assembly of silicon strip detector modules for the ATLAS upgrade. Trials were carried out to determine the ease of use, the thermal conduction and shear strength, thermal cycling, radiation hardness, corrosion resistance and shear strength tests. These investigations led to the exclusion of three UV cure glues as well as the glue pad.
Three UV cure glues were found to be possible better alternatives. Results from electrical tests of first prototype modules constructed using these glues are presented.
△ Less
Submitted 26 April, 2016; v1 submitted 24 August, 2015;
originally announced August 2015.