Showing 1–25 of 25 results for author: Peters, I R

Bubble collapse near porous plates

Authors: Elijah D. Andrews, David Fernández Rivas, Ivo R. Peters

Abstract: The collapse of a gas or vapour bubble near a non-porous boundary is directed at the boundary due to the asymmetry induced by the nearby boundary. High surface pressure and shear stress from this collapse can damage, or clean, the surface. A porous boundary, such as a filter, would act similarly to a non-porous boundary but with reduced asymmetry and thus reduced effect. Prior research has measure… ▽ More The collapse of a gas or vapour bubble near a non-porous boundary is directed at the boundary due to the asymmetry induced by the nearby boundary. High surface pressure and shear stress from this collapse can damage, or clean, the surface. A porous boundary, such as a filter, would act similarly to a non-porous boundary but with reduced asymmetry and thus reduced effect. Prior research has measured the cleaning effect of bubbles on filters using ultrasonic cleaning, but it is not known how the bubble dynamics are fundamentally affected by the porosity of the surface. We address this question experimentally by investigating how the standoff distance, porosity, pore size, and pore shape affect two collapse properties: bubble displacement and bubble rebound size. We show that these properties depend primarily on the standoff distance and porosity of the boundary and extend a previously developed numerical model that approximates this behaviour. Using the numerical model in combination with experimental data, we show that bubble displacement and bubble rebound size each collapse onto respective single curves. △ Less

Submitted 29 March, 2023; v1 submitted 7 October, 2022; originally announced October 2022.

Modelling bubble collapse anisotropy in complex geometries

Authors: Elijah D. Andrews, Ivo R. Peters

Abstract: A gas or vapor bubble collapsing in the vicinity of a rigid boundary displaces towards the boundary and produces a high-speed jet directed at the boundary. This behavior has been shown to be a function of the 'anisotropy' of the collapse, measured by a dimensionless representation of the Kelvin impulse known as the anisotropy parameter [Supponen et al., J. Fluid Mech. 802, 263-293 (2016)]. However… ▽ More A gas or vapor bubble collapsing in the vicinity of a rigid boundary displaces towards the boundary and produces a high-speed jet directed at the boundary. This behavior has been shown to be a function of the 'anisotropy' of the collapse, measured by a dimensionless representation of the Kelvin impulse known as the anisotropy parameter [Supponen et al., J. Fluid Mech. 802, 263-293 (2016)]. However, characterisation of the anisotropy parameter in different geometries has been limited to simplified analytic solutions. In this work we develop an inexpensive numerical model, based on the Boundary Element Method, capable of predicting the anisotropy parameter for any rigid complex geometry. We experimentally explore a robust measure of bubble displacement, showing that the bubble displacement in a range of complex geometries behaves as a single function of the predicted anisotropy parameter values. △ Less

Submitted 15 November, 2022; v1 submitted 20 July, 2022; originally announced July 2022.

Lasting effects of discontinuous shear thickening in cornstarch suspensions upon flow cessation

Authors: Jae Hyung Cho, Andrew H. Griese, Ivo R. Peters, Irmgard Bischofberger

Abstract: Dense suspensions that exhibit discontinuous shear thickening (DST) undergo complex stress relaxation when the flow abruptly stops. Using rotational rheometry, we study the two-step relaxation of aqueous cornstarch suspensions out of the DST state upon flow cessation and show that the DST fluid retains the memory of its shear-thickening state until the shear stress reaches a constant value at late… ▽ More Dense suspensions that exhibit discontinuous shear thickening (DST) undergo complex stress relaxation when the flow abruptly stops. Using rotational rheometry, we study the two-step relaxation of aqueous cornstarch suspensions out of the DST state upon flow cessation and show that the DST fluid retains the memory of its shear-thickening state until the shear stress reaches a constant value at late times. We find that this residual stress at the end of the relaxation increases with the steady-state viscosity before the cessation. Furthermore, the timescales that characterize the two-step exponential decay of the shear stress exhibit near linear dependence on the steady-state viscosity. Within the current framework that ascribes DST to the breakdown of hydrodynamic lubrication layers leading to interparticle frictional contacts, the lasting effects of the steady-state viscosity suggest that the memory of frictional contacts persists until the end of the relaxation, despite the presence of repulsive forces between the particles. These results indicate that complete, spontaneous relaxation of the system out of DST is stalled by the partial retention of the frictional force chains, which may be caused by the stationary boundaries and the adhesion between cornstarch particles. △ Less

Submitted 2 November, 2021; originally announced November 2021.

Characterizing the surface texture of a dense suspension undergoing dynamic jamming

Authors: Olav Rømcke, Ivo R. Peters, R. Jason Hearst

Abstract: Measurements of the surface velocity and surface texture of a freely propagating shear jamming front in a dense suspension are compared. The velocity fields are captured with particle image velocimetry (PIV), while the surface texture is captured in a separated experiment by observing a direct reflection on the suspension surface with high-speed cameras. A method for quantifying the surface featur… ▽ More Measurements of the surface velocity and surface texture of a freely propagating shear jamming front in a dense suspension are compared. The velocity fields are captured with particle image velocimetry (PIV), while the surface texture is captured in a separated experiment by observing a direct reflection on the suspension surface with high-speed cameras. A method for quantifying the surface features and their orientation is presented based on the fast Fourier transform of localised windows. The region that exhibits strong surface features corresponds to the the solid-like jammed region identified via the PIV measurements. Moreover, the surface features within the jammed region are predominantly oriented in the same direction as the eigenvectors of the strain tensor. Thus, from images of the free surface, our analysis is able to show that the surface texture contains information on the principle strain directions and the propagation of the jamming front. △ Less

Submitted 3 September, 2021; v1 submitted 9 July, 2021; originally announced July 2021.

Collision of Dynamic Jamming Fronts in a Dense Suspension

Authors: Olav Ro mcke, Ivo R. Peters, R. Jason Hearst

Abstract: Dynamic jamming is a phenomenon whereby a dense suspension switches from a fluid-like to a solid-like state when subjected to sufficient stress and deformation. Large enough systems show that this transition is accompanied by a distinct jamming front. We present an experimental study where two jamming fronts are created simultaneously using two cylinders moving in parallel. We focus our observatio… ▽ More Dynamic jamming is a phenomenon whereby a dense suspension switches from a fluid-like to a solid-like state when subjected to sufficient stress and deformation. Large enough systems show that this transition is accompanied by a distinct jamming front. We present an experimental study where two jamming fronts are created simultaneously using two cylinders moving in parallel. We focus our observations on the collision of the jammed regions when the two fronts meet. Surprisingly, our measurements, combining surface texture visualization and time-resolved particle image velocimetry, show the formation of an unjammed region contained within the otherwise jammed suspension. △ Less

Submitted 9 July, 2021; originally announced July 2021.

Cavity collapse near slot geometries

Authors: Elijah D. Andrews, David Fernández Rivas, Ivo R. Peters

Abstract: The collapse of a gas or vapour bubble near a solid boundary produces a jet directed towards the boundary. High surface pressure and shear stress induced by this jet can damage, or clean, the surface. More complex geometries will result in changes in collapse behaviour, in particular the direction of the jet. The majority of prior research has focused on simple flat boundaries or limited cases wit… ▽ More The collapse of a gas or vapour bubble near a solid boundary produces a jet directed towards the boundary. High surface pressure and shear stress induced by this jet can damage, or clean, the surface. More complex geometries will result in changes in collapse behaviour, in particular the direction of the jet. The majority of prior research has focused on simple flat boundaries or limited cases with analytic solutions. We numerically and experimentally investigate how a slot in a flat boundary affects the jet direction for a single bubble. We use a boundary element model to predict how the jet direction depends on key geometric parameters and show that the results collapse to a single curve when the parameters are normalised appropriately. We then experimentally validate the predictions using laser-induced cavitation and compare the experimental results to the predicted dependencies. This research reveals a tendency for the jet to be directed away from a slot and shows that the jet direction is independent of slot height for slots of sufficient height. △ Less

Submitted 9 April, 2020; originally announced April 2020.

Journal ref: J. Fluid Mech. 901 (2020) A29

Getting jammed in all directions: Dynamic shear jamming around a cylinder towed through a dense suspension

Authors: Olav Rømcke, Ivo R. Peters, R. Jason Hearst

Abstract: Experimental results of towing a cylinder through a dense suspension of cornstarch and sucrose-water are presented. Focus is placed on the jamming fronts that exist in such systems. The literature has concentrated on the propagation of the jammed region under pushing, pulling or shearing conditions independently. How the different fronts interact and if the fronts are symmetric when generated simu… ▽ More Experimental results of towing a cylinder through a dense suspension of cornstarch and sucrose-water are presented. Focus is placed on the jamming fronts that exist in such systems. The literature has concentrated on the propagation of the jammed region under pushing, pulling or shearing conditions independently. How the different fronts interact and if the fronts are symmetric when generated simultaneously has remained unexplored. Investigating this is our main goal. With the current setup, we are able to view a continuous, quasi-2D field around the cylinder. As such, a new way of generating jamming fronts is presented whereby pushing, pulling and shearing can be examined simultaneously. In agreement with previous studies, the front propagates roughly twice as fast in the longitudinal direction compared to the transverse direction, which is attributed to a single underlying onset strain, regardless of orientation from the cylinder. Although the jamming front shows nearly perfect transverse symmetry, there is clear longitudinal asymmetry. This is evident in the velocity and strain fields, and is also detectable in the front propagation velocity and onset strain. △ Less

Submitted 11 June, 2021; v1 submitted 3 April, 2020; originally announced April 2020.

Journal ref: Phys. Rev. Fluids 6, 063301 (2021)

Jet direction in bubble collapse within rectangular and triangular channels

Authors: Lebo Molefe, Ivo R. Peters

Abstract: A vapor bubble collapsing near a solid boundary in a liquid produces a liquid jet that points toward the boundary. The direction of this jet has been studied for boundaries such as flat planes and parallel walls enclosing a channel. Extending these investigations to enclosed polygonal boundaries, we experimentally measure jet direction for collapsing bubbles inside a square and an equilateral tria… ▽ More A vapor bubble collapsing near a solid boundary in a liquid produces a liquid jet that points toward the boundary. The direction of this jet has been studied for boundaries such as flat planes and parallel walls enclosing a channel. Extending these investigations to enclosed polygonal boundaries, we experimentally measure jet direction for collapsing bubbles inside a square and an equilateral triangular channel. Following the method of Tagawa and Peters (Phys. Rev. Fluids 3, 081601, 2018) for predicting the jet direction in corners, we model the bubble as a sink in a potential flow and demonstrate by experiment that analytical solutions accurately predict jet direction within an equilateral triangle and square. We further use the method to develop predictions for several other polygons, specifically, a rectangle, an isosceles right triangle, and a $30^{\circ}$-$60^{\circ}$-$90^{\circ}$ right triangle. △ Less

Submitted 20 October, 2019; originally announced October 2019.

Journal ref: Phys. Rev. E 100, 063105 (2019)

Bubble Collapse and Jet Formation in Corner Geometries

Authors: Yoshiyuki Tagawa, Ivo R. Peters

Abstract: The collapse of a vapor bubble near a flat solid boundary results in the formation of a jet that is directed towards the boundary. In more complex geometries such as corners, predictions of the collapse cannot be made in a straightforward manner due to the loss of axial symmetry. We experimentally investigate the bubble collapse and jet formation in corners formed of two flat solid boundaries with… ▽ More The collapse of a vapor bubble near a flat solid boundary results in the formation of a jet that is directed towards the boundary. In more complex geometries such as corners, predictions of the collapse cannot be made in a straightforward manner due to the loss of axial symmetry. We experimentally investigate the bubble collapse and jet formation in corners formed of two flat solid boundaries with different opening angles. Using potential flow analysis, we accurately predict the direction of the jet and bubble displacement. We further show that for a corner with an opening angle $α$, there exist analytic solutions that predict the jet direction for all the cases $α=π/n$, where $n$ is a natural number. These solutions cover, in discrete steps, the full range of corners from the limiting case of a bubble near a single wall ($n=1$) up to a bubble in between parallel walls ($n\rightarrow\infty$). △ Less

Submitted 16 July, 2018; v1 submitted 29 May, 2018; originally announced May 2018.

Journal ref: Phys. Rev. Fluids 3, 081601 (2018)

Constitutive relations for shear fronts in shear-thickening suspensions

Authors: Endao Han, Matthieu Wyart, Ivo R. Peters, Heinrich M. Jaeger

Abstract: We study the fronts that appear when a shear-thickening suspension is submitted to a sudden driving force at a boundary. Using a quasi-one-dimensional experimental geometry, we extract the front shape and the propagation speed from the suspension flow field and map out their dependence on applied shear. We find that the relation between stress and velocity is quadratic, as is generally true for in… ▽ More We study the fronts that appear when a shear-thickening suspension is submitted to a sudden driving force at a boundary. Using a quasi-one-dimensional experimental geometry, we extract the front shape and the propagation speed from the suspension flow field and map out their dependence on applied shear. We find that the relation between stress and velocity is quadratic, as is generally true for inertial effects in liquids, but with a pre-factor that can be much larger than the material density. We show that these experimental findings can be explained by an extension of the Wyart-Cates model, which was originally developed to describe steady-state shear-thickening. This is achieved by introducing a sole additional parameter: the characteristic strain scale that controls the crossover from start-up response to steady-state behavior. The theoretical framework we obtain unifies both transient and steady-state properties of shear-thickening materials. △ Less

Submitted 6 November, 2017; originally announced November 2017.

Comments: 17 pages, 13 figures

Journal ref: Phys. Rev. Fluids 3, 073301 (2018)

High-speed ultrasound imaging in dense suspensions reveals impact-activated solidification due to dynamic shear jamming

Authors: Endao Han, Ivo R. Peters, Heinrich M. Jaeger

Abstract: A remarkable property of dense suspensions is that they can transform from liquid-like at rest to solid-like under sudden impact. Previous work showed that this impact-induced solidification involves rapidly moving jamming fronts; however, details of this process have remained unresolved. Here we use high-speed ultrasound imaging to probe non-invasively how the interior of a dense suspension respo… ▽ More A remarkable property of dense suspensions is that they can transform from liquid-like at rest to solid-like under sudden impact. Previous work showed that this impact-induced solidification involves rapidly moving jamming fronts; however, details of this process have remained unresolved. Here we use high-speed ultrasound imaging to probe non-invasively how the interior of a dense suspension responds to impact. Measuring the speed of sound we demonstrate that the solidification proceeds without a detectable increase in packing fraction, and imaging the evolving flow field we find that the shear intensity is maximized right at the jamming front. Taken together, this provides direct experimental evidence for jamming by shear, rather than densification, as driving the transformation to solid-like behavior. Based on these findings we propose a new model to explain the anisotropy in the propagation speed of the fronts and delineate the onset conditions for dynamic shear jamming in suspensions. △ Less

Submitted 1 April, 2016; originally announced April 2016.

Comments: 9 pages, 3 figures

From splashing to bouncing: the influence of viscosity on the impact of suspension droplets on a solid surface

Authors: Martin H. Klein Schaarsberg, Ivo R. Peters, Menachem Stern, Kevin Dodge, Wendy W. Zhang, Heinrich M. Jaeger

Abstract: We experimentally investigated the splashing of dense suspension droplets impacting a solid surface, extending prior work to the regime where the viscosity of the suspending liquid becomes a significant parameter. The overall behavior can be described by a combination of two trends. The first one is that the splashing becomes favored when the kinetic energy of individual particles at the surface o… ▽ More We experimentally investigated the splashing of dense suspension droplets impacting a solid surface, extending prior work to the regime where the viscosity of the suspending liquid becomes a significant parameter. The overall behavior can be described by a combination of two trends. The first one is that the splashing becomes favored when the kinetic energy of individual particles at the surface of a droplet overcomes the confinement produced by surface tension. This is expressed by a particle-based Weber number $We_p$. The second is that splashing is suppressed by increasing the viscosity of the solvent. This is expressed by the Stokes number $St$, which influences the effective coefficient of restitution of colliding particles. We developed a phase diagram where the splashing onset is delineated as a function of both $We_p$ and $St$. A surprising result occurs at very small Stokes number, where not only splashing is suppressed but also plastic deformation of the droplet. This leads to a situation where droplets can bounce back after impact, an observation we are able to reproduce using discrete particle numerical simulations that take into account viscous interaction between particles and elastic energy. △ Less

Submitted 17 May, 2016; v1 submitted 10 March, 2016; originally announced March 2016.

Journal ref: Phys. Rev. E 93, 062609 (2016)

Dynamic shear jamming in dense granular suspensions under extension

Authors: Sayantan Majumdar, Ivo R. Peters, Endao Han, Heinrich M. Jaeger

Abstract: Unlike dry granular materials, a dense granular suspension like cornstarch in water can strongly resist extensional flows. At low extension rates, such a suspension behaves like a viscous liquid, but rapid extension results in a response where stresses far exceed the predictions of lubrication hydrodynamics and capillarity. To understand this remarkable mechanical response, we experimentally measu… ▽ More Unlike dry granular materials, a dense granular suspension like cornstarch in water can strongly resist extensional flows. At low extension rates, such a suspension behaves like a viscous liquid, but rapid extension results in a response where stresses far exceed the predictions of lubrication hydrodynamics and capillarity. To understand this remarkable mechanical response, we experimentally measure the normal force imparted by a large bulk of the suspension on a plate moving vertically upward at a controlled velocity. We observe that above a velocity threshold, the peak force increases by orders of magnitude. Using fast ultrasound imaging we map out the local velocity profiles inside the suspension which reveal the formation of a growing jammed region under rapid extension. This region interacts with the rigid boundaries of the container through strong velocity gradients, suggesting a direct connection to the recently proposed shear-jamming mechanism. △ Less

Submitted 9 December, 2016; v1 submitted 7 March, 2016; originally announced March 2016.

Comments: Accepted for publication in Phys. Rev. E

Journal ref: Phys. Rev. E 95, 012603 (2017)

Volume entrained in the wake of a disc intruding into an oil-water interface

Authors: Ivo R. Peters, Matteo Madonia, Detlef Lohse, Devaraj van der Meer

Abstract: An object moving through a plane interface into a fluid deforms the interface in such a way that fluid from one side of the interface is entrained into the other side, a phenomenon known as Darwin's drift. We investigate this phenomenon experimentally using a disc which is started exactly at the interface of two immiscible fluids, namely oil and water. First, we observe that due to the density dif… ▽ More An object moving through a plane interface into a fluid deforms the interface in such a way that fluid from one side of the interface is entrained into the other side, a phenomenon known as Darwin's drift. We investigate this phenomenon experimentally using a disc which is started exactly at the interface of two immiscible fluids, namely oil and water. First, we observe that due to the density difference between the two fluids the deformation of the interface is influenced by gravity, and show that there exits a time window of universal behavior. Secondly, we show by comparing with boundary integral simulations that, even though the deformation is universal, our results cannot be fully explained by potential flow solutions. We attribute this difference to the starting vortex, which is created in the wake of the disc. Universal behavior is preserved, however, because the size and strength of the vortex shows the same universality as the potential flow solution. △ Less

Submitted 12 January, 2016; originally announced January 2016.

Journal ref: Phys. Rev. Fluids 1, 033901 (2016)

Dynamic jamming of iceberg-choked fjords

Authors: Ivo R. Peters, Jason M. Amundson, Ryan Cassotto, Mark Fahnestock, Kristopher N. Darnell, Martin Truffer, Wendy W. Zhang

Abstract: We investigate the dynamics of ice mélange by analyzing rapid motion recorded by a time-lapse camera and terrestrial radar during several calving events that occurred at Jakobshavn Isbræ, Greenland. During calving events (1) the kinetic energy of the ice mélange is two orders of magnitude smaller than the total energy released during the events, (2) a jamming front propagates through the ice mélan… ▽ More We investigate the dynamics of ice mélange by analyzing rapid motion recorded by a time-lapse camera and terrestrial radar during several calving events that occurred at Jakobshavn Isbræ, Greenland. During calving events (1) the kinetic energy of the ice mélange is two orders of magnitude smaller than the total energy released during the events, (2) a jamming front propagates through the ice mélange at a rate that is an order of magnitude faster than the motion of individual icebergs, (3) the ice mélange undergoes initial compaction followed by slow relaxation and extension, and (4) motion of the ice mélange gradually decays before coming to an abrupt halt. These observations indicate that the ice mélange experiences widespread jamming during calving events and is always close to being in a jammed state during periods of terminus quiescence. We therefore suspect that local jamming influences longer timescale ice mélange dynamics and stress transmission. △ Less

Submitted 3 December, 2014; originally announced December 2014.

Comments: 14 pages, 4 figures

Quasi-2D dynamic jamming in cornstarch suspensions: visualization and force measurements

Authors: Ivo R. Peters, Heinrich M. Jaeger

Abstract: We report experiments investigating jamming fronts in a floating layer of cornstarch suspension. The suspension has a packing fraction close to jamming, which dynamically turns into a solid when impacted at a high speed. We show that the front propagates in both axial and transverse direction from the point of impact, with a constant ratio between the two directions of propagation of approximately… ▽ More We report experiments investigating jamming fronts in a floating layer of cornstarch suspension. The suspension has a packing fraction close to jamming, which dynamically turns into a solid when impacted at a high speed. We show that the front propagates in both axial and transverse direction from the point of impact, with a constant ratio between the two directions of propagation of approximately 2. Inside the jammed solid, we observe an additional compression, which results from the increasing stress as the solid grows. During the initial growth of the jammed solid, we measure a force response that can be completely accounted for by added mass. Only once the jamming front reaches a boundary, the added mass cannot account for the measured force anymore. We do not, however, immediately see a strong force response as we would expect when compressing a jammed packing. Instead, we observe a delay in the force response on the pusher, which corresponds to the time it takes for the system to develop a close to uniform velocity gradient that spans the complete system. △ Less

Submitted 3 December, 2014; v1 submitted 24 April, 2014; originally announced April 2014.

Comments: 7 pages, 7 figures

Journal ref: Soft Matter 10 (2014) 6564-6570

Oscillating and star-shaped drops levitated by an airflow

Authors: Wilco Bouwhuis, Koen G. Winkels, Ivo R. Peters, Philippe Brunet, Devaraj van der Meer, Jacco H. Snoeijer

Abstract: We investigate the spontaneous oscillations of drops levitated above an air cushion, eventually inducing a breaking of axisymmetry and the appearance of `star drops'. This is strongly reminiscent of the Leidenfrost stars that are observed for drops floating above a hot substrate. The key advantage of this work is that we inject the airflow at a constant rate below the drop, thus eliminating therma… ▽ More We investigate the spontaneous oscillations of drops levitated above an air cushion, eventually inducing a breaking of axisymmetry and the appearance of `star drops'. This is strongly reminiscent of the Leidenfrost stars that are observed for drops floating above a hot substrate. The key advantage of this work is that we inject the airflow at a constant rate below the drop, thus eliminating thermal effects and allowing for a better control of the flow rate. We perform experiments with drops of different viscosities and observe stable states, oscillations and chimney instabilities. We find that for a given drop size the instability appears above a critical flow rate, where the latter is largest for small drops. All these observations are reproduced by numerical simulations, where we treat the drop using potential flow and the gas as a viscous lubrication layer. Qualitatively, the onset of instability agrees with the experimental results, although the typical flow rates are too large by a factor 10. Our results demonstrate that thermal effects are not important for the formation of star drops, and strongly suggest a purely hydrodynamic mechanism for the formation of Leidenfrost stars. △ Less

Submitted 23 May, 2013; originally announced May 2013.

Splashing onset in dense suspension droplets

Authors: Ivo R. Peters, Qin Xu, Heinrich M. Jaeger

Abstract: We investigate the impact of droplets of dense suspensions onto a solid substrate. We show that a global hydrodynamic balance is unable to predict the splash onset and propose to replace it by an energy balance at the level of the particles in the suspension. We experimentally verify that the resulting, particle-based Weber number gives a reliable, particle size and density dependent splash onset… ▽ More We investigate the impact of droplets of dense suspensions onto a solid substrate. We show that a global hydrodynamic balance is unable to predict the splash onset and propose to replace it by an energy balance at the level of the particles in the suspension. We experimentally verify that the resulting, particle-based Weber number gives a reliable, particle size and density dependent splash onset criterion. We further show that the same argument also explains why in bimodal systems smaller particles are more likely to escape than larger ones. △ Less

Submitted 10 June, 2013; v1 submitted 1 March, 2013; originally announced March 2013.

Air flow in a collapsing cavity

Authors: Ivo R. Peters, Stephan Gekle, Detlef Lohse, Devaraj van der Meer

Abstract: We experimentally study the airflow in a collapsing cavity created by the impact of a circular disk on a water surface. We measure the air velocity in the collapsing neck in two ways: Directly, by means of employing particle image velocimetry of smoke injected into the cavity and indirectly, by determining the time rate of change of the volume of the cavity at pinch-off and deducing the air flow i… ▽ More We experimentally study the airflow in a collapsing cavity created by the impact of a circular disk on a water surface. We measure the air velocity in the collapsing neck in two ways: Directly, by means of employing particle image velocimetry of smoke injected into the cavity and indirectly, by determining the time rate of change of the volume of the cavity at pinch-off and deducing the air flow in the neck under the assumption that the air is incompressible. We compare our experiments to boundary integral simulations and show that close to the moment of pinch-off, compressibility of the air starts to play a crucial role in the behavior of the cavity. Finally, we measure how the air flow rate at pinch-off depends on the Froude number and explain the observed dependence using a theoretical model of the cavity collapse. △ Less

Submitted 18 February, 2013; originally announced February 2013.

Splash wave and crown breakup after disc impact on a liquid surface

Authors: Ivo R. Peters, Devaraj van der Meer, J. M. Gordillo

Abstract: In this paper we analyze the impact of a circular disc on a free surface using experiments, potential flow numerical simulations and theory. We focus our attention both on the study of the generation and possible breakup of the splash wave created after the impact and on the calculation of the force on the disc. We have experimentally found that drops are only ejected from the rim located at the t… ▽ More In this paper we analyze the impact of a circular disc on a free surface using experiments, potential flow numerical simulations and theory. We focus our attention both on the study of the generation and possible breakup of the splash wave created after the impact and on the calculation of the force on the disc. We have experimentally found that drops are only ejected from the rim located at the top part of the splash --giving rise to what is known as the crown splash-- if the impact Weber number exceeds a threshold value $\Weber_{crit}\simeq 140$. We explain this threshold by defining a local Bond number $Bo_{tip}$ based on the rim deceleration and its radius of curvature, with which we show using both numerical simulations and experiments that a crown splash only occurs when $Bo_{tip}\gtrsim 1$, revealing that the rim disrupts due to a Rayleigh-Taylor instability. Neglecting the effect of air, we show that the flow in the region close to the disc edge possesses a Weber-number-dependent self-similar structure for every Weber number. From this we demonstrate that $\Bond_{tip}\propto\Weber$, explaining both why the transition to crown splash can be characterized in terms of the impact Weber number and why this transition occurs for $We_{crit}\simeq 140$. Next, including the effect of air, we have developed a theory which predicts the time-varying thickness of the very thin air cushion that is entrapped between the impacting solid and the liquid. Our analysis reveals that gas critically affect the velocity of propagation of the splash wave as well as the time-varying force on the disc, $F_D$. The existence of the air layer also limits the range of times in which the self-similar solution is valid and, accordingly, the maximum deceleration experienced by the liquid rim, what sets the length scale of the splash drops ejected when $We>\Weber_{crit}$. △ Less

Submitted 18 February, 2013; v1 submitted 28 November, 2012; originally announced November 2012.

Maximal air bubble entrainment at liquid drop impact

Authors: Wilco Bouwhuis, Roeland C. A. van der Veen, Tuan Tran, Diederik L. Keij, Koen G. Winkels, Ivo R. Peters, Devaraj van der Meer, Chao Sun, Jacco H. Snoeijer, Detlef Lohse

Abstract: At impact of a liquid drop on a solid surface an air bubble can be entrapped. Here we show that two competing effects minimize the (relative) size of this entrained air bubble: For large drop impact velocity and large droplets the inertia of the liquid flattens the entrained bubble, whereas for small impact velocity and small droplets capillary forces minimize the entrained bubble. However, we dem… ▽ More At impact of a liquid drop on a solid surface an air bubble can be entrapped. Here we show that two competing effects minimize the (relative) size of this entrained air bubble: For large drop impact velocity and large droplets the inertia of the liquid flattens the entrained bubble, whereas for small impact velocity and small droplets capillary forces minimize the entrained bubble. However, we demonstrate experimentally, theoretically, and numerically that in between there is an optimum, leading to maximal air bubble entrapment. Our results have a strong bearing on various applications in printing technology, microelectronics, immersion lithography, diagnostics, or agriculture. △ Less

Submitted 21 May, 2012; originally announced May 2012.

Comments: 4 pages

Highly focused supersonic microjets: numerical simulations

Authors: Ivo R. Peters, Yoshiyuki Tagawa, Nikolai Oudalov, Chao Sun, Andrea Prosperetti, Detlef Lohse, Devaraj van der Meer

Abstract: By focusing a laser pulse inside a capillary partially filled with liquid, a vapour bubble is created which emits a pressure wave. This pressure wave travels through the liquid and creates a fast, focused axisymmetric microjet when it is reflected at the meniscus. We numerically investigate the formation of this microjet using axisymmetric boundary-integral simulations, where we model the pressure… ▽ More By focusing a laser pulse inside a capillary partially filled with liquid, a vapour bubble is created which emits a pressure wave. This pressure wave travels through the liquid and creates a fast, focused axisymmetric microjet when it is reflected at the meniscus. We numerically investigate the formation of this microjet using axisymmetric boundary-integral simulations, where we model the pressure wave as a pressure pulse applied on the bubble. We find a good agreement between the simulations and experimental results in terms of the time evolution of the jet and on all parameters that can be compared directly. We present a simple analytical model that accurately predicts the velocity of the jet after the pressure pulse and its maximum velocity. △ Less

Submitted 27 September, 2012; v1 submitted 22 March, 2012; originally announced March 2012.

Highly focused supersonic microjets

Authors: Yoshiyuki Tagawa, Nikolai Oudalov, Claas Willem Visser, Ivo R. Peters, Deveraj van der Meer, Chao Sun, Andrea Prosperetti, Detlef Lohse

Abstract: The paper describes the production of thin, focused microjets with velocities up to 850 m/s by the rapid vaporization of a small mass of liquid in an open liquid-filled capillary. The vaporization is caused by the absorption of a low-energy laser pulse. A likely explanation of the observed phenomenon is based on the im**ement of the shock wave caused by the nearly-instantaneous vaporization on t… ▽ More The paper describes the production of thin, focused microjets with velocities up to 850 m/s by the rapid vaporization of a small mass of liquid in an open liquid-filled capillary. The vaporization is caused by the absorption of a low-energy laser pulse. A likely explanation of the observed phenomenon is based on the im**ement of the shock wave caused by the nearly-instantaneous vaporization on the free surface of the liquid. An experimental study of the dependence of the jet velocity on several parameters is conducted, and a semi-empirical relation for its prediction is developed. The coherence of the jets, their high velocity and good reproducibility and controllability are unique features of the system described. A possible application is to the development of needle-free drug injection systems which are of great importance for global health care. △ Less

Submitted 27 April, 2012; v1 submitted 12 December, 2011; originally announced December 2011.

Comments: 10 pages, 11figures

Journal ref: Phys. Rev. X 2, 031002 (2012)

Collapse of a non-axisymmetric, impact-created air cavity in water

Authors: Oscar R. Enriquez, Ivo R. Peters, Stephan Gekle, Laura E. Schmidt, Detlef Lohse, Devaraj Van Der Meer

Abstract: The axisymmetric collapse of a cylindrical air cavity in water follows a universal power law with logarithmic corrections. Nonetheless, it has been suggested that the introduction of a small azimuthal disturbance induces a long term memory effect, reflecting in oscillations which are no longer universal but remember the initial condition. In this work, we create non-axisymmetric air cavities by dr… ▽ More The axisymmetric collapse of a cylindrical air cavity in water follows a universal power law with logarithmic corrections. Nonetheless, it has been suggested that the introduction of a small azimuthal disturbance induces a long term memory effect, reflecting in oscillations which are no longer universal but remember the initial condition. In this work, we create non-axisymmetric air cavities by driving a metal disc through an initially-quiescent water surface and observe their subsequent gravity-induced collapse. The cavities are characterized by azimuthal harmonic disturbances with a single mode number $m$ and amplitude $a_m$. For small initial distortion amplitude (1 or 2% of the mean disc radius), the cavity walls oscillate linearly during collapse, with nearly constant amplitude and increasing frequency. As the amplitude is increased, higher harmonics are triggered in the oscillations and we observe more complex pinch-off modes. For small amplitude disturbances we compare our experimental results with the model for the amplitude of the oscillations by Schmidt et al. (2009) and the model for the collapse of an axisymmetric impact-created cavity previously proposed by Bergmann et al. (2009b). By combining these two models we can reconstruct the three-dimensional shape of the cavity at any time before pinch-off. △ Less

Submitted 2 March, 2012; v1 submitted 27 September, 2011; originally announced September 2011.

Comments: 18 pages, 13 figures

Collapse of Non-Axisymmetric Cavities

Authors: Oscar R. Enriquez, Ivo R. Peters, Stephan Gekle, Laura Schmidt, Michel Versluis, Devaraj van der Meer, Detlef Lohse

Abstract: A round disk with a harmonic disturbance impacts on a water surface and creates a non-axisymmetric cavity which collapses under the influence of hydrostatic pressure. We use disks deformed with mode m=2 to m=6. For all mode numbers we find clear evidence for a phase inversion of the cavity wall during the collapse. We present a fluid dynamics video showing high speed imaging of different modes,… ▽ More A round disk with a harmonic disturbance impacts on a water surface and creates a non-axisymmetric cavity which collapses under the influence of hydrostatic pressure. We use disks deformed with mode m=2 to m=6. For all mode numbers we find clear evidence for a phase inversion of the cavity wall during the collapse. We present a fluid dynamics video showing high speed imaging of different modes, pointing out the characteristic features during collapse. △ Less

Submitted 14 October, 2009; originally announced October 2009.