-
Spatial Multiplexing of QPSK Signals with a Single Radio: Antenna Design and Over-the-Air Experiments
Authors:
Mohsen Yousefbeiki,
Andrew C. M. Austin,
Juan R. Mosig,
Andreas Burg,
Julien Perruisseau-Carrier
Abstract:
The paper describes the implementation and performance analysis of the first fully-operational beam-space MIMO antenna for the spatial multiplexing of two QPSK streams. The antenna is composed of a planar three-port radiator with two varactor diodes terminating the passive ports. Pattern reconfiguration is used to encode the MIMO information onto orthogonal virtual basis patterns in the far-field.…
▽ More
The paper describes the implementation and performance analysis of the first fully-operational beam-space MIMO antenna for the spatial multiplexing of two QPSK streams. The antenna is composed of a planar three-port radiator with two varactor diodes terminating the passive ports. Pattern reconfiguration is used to encode the MIMO information onto orthogonal virtual basis patterns in the far-field. A measurement campaign was conducted to compare the performance of the beam-space MIMO system with a conventional 2-by-?2 MIMO system under realistic propagation conditions. Propagation measurements were conducted for both systems and the mutual information and symbol error rates were estimated from Monte-Carlo simulations over the measured channel matrices. The results show the beam-space MIMO system and the conventional MIMO system exhibit similar finite-constellation capacity and error performance in NLOS scenarios when there is sufficient scattering in the channel. In comparison, in LOS channels, the capacity performance is observed to depend on the relative polarization of the receiving antennas.
△ Less
Submitted 30 August, 2016;
originally announced August 2016.
-
Gate-controlled mid-infrared light bending with aperiodic graphene nanoribbons array
Authors:
Eduardo Carrasco,
Michele Tamagnone,
Juan R. Mosig,
Tony Low,
Julien Perruisseau-Carrier
Abstract:
Graphene plasmonic nanostructures enable subwavelength confinement of electromagnetic energy from the mid-infrared down to the terahertz frequencies. By exploiting the spectrally varying light scattering phase at vicinity of the resonant frequency of the plasmonic nanostructure, it is possible to control the angle of reflection of an incoming light beam. We demonstrate, through full-wave electroma…
▽ More
Graphene plasmonic nanostructures enable subwavelength confinement of electromagnetic energy from the mid-infrared down to the terahertz frequencies. By exploiting the spectrally varying light scattering phase at vicinity of the resonant frequency of the plasmonic nanostructure, it is possible to control the angle of reflection of an incoming light beam. We demonstrate, through full-wave electromagnetic simulations based on Maxwell equations, the electrical control of the angle of reflection of a mid-infrared light beam by using an aperiodic array of graphene nanoribbons, whose widths are engineered to produce a spatially varying reflection phase profile that allows for the construction of a far-field collimated beam towards a predefined direction.
△ Less
Submitted 2 December, 2014;
originally announced December 2014.
-
Nonlocal Electromagnetic Response of Graphene Nanostructures
Authors:
Arya Fallahi,
Tony Low,
Michele Tamagnone,
Julien Perruisseau-Carrier
Abstract:
Nonlocal electromagnetic effects of graphene arise from its naturally dispersive dielectric response. We present semi-analytical solutions of nonlocal Maxwell's equations for graphene nano-ribbons array with features around 100 nm, where we found prominent departures from its local response. Interestingly, the nonlocal corrections are stronger for light polarization parallel to the ribbons, which…
▽ More
Nonlocal electromagnetic effects of graphene arise from its naturally dispersive dielectric response. We present semi-analytical solutions of nonlocal Maxwell's equations for graphene nano-ribbons array with features around 100 nm, where we found prominent departures from its local response. Interestingly, the nonlocal corrections are stronger for light polarization parallel to the ribbons, which manifests as additional broadening of the Drude peak. For the perpendicular polarization case, nonlocal effects lead to blue-shifts of the plasmon peaks. These manifestations provide a physical measure of nonlocal effects, and we quantify their dependence on ribbon width, do** and wavelength.
△ Less
Submitted 7 October, 2014;
originally announced October 2014.
-
Self-biased Reconfigurable Graphene Stacks for Terahertz Plasmonics
Authors:
J. S. Gomez-Diaz,
C. Moldovan,
S. Capdevilla,
J. Romeu,
L. S. Bernard,
A. Magrez,
A. M. Ionescu,
J. Perruisseau-Carrier
Abstract:
The gate-controllable complex conductivity of graphene offers unprecedented opportunities for reconfigurable plasmonics at THz and mid-IR frequencies. However, the requirement of a gating electrode close to graphene and the single `control knob' that this approach offers for graphene conductivity limits the practical implementation and performance of graphene-controllable plasmonic devices. Herein…
▽ More
The gate-controllable complex conductivity of graphene offers unprecedented opportunities for reconfigurable plasmonics at THz and mid-IR frequencies. However, the requirement of a gating electrode close to graphene and the single `control knob' that this approach offers for graphene conductivity limits the practical implementation and performance of graphene-controllable plasmonic devices. Herein, we report on graphene stacks composed of two or more graphene monolayers separated by electrically thin dielectrics and present a simple and rigorous theoretical framework for their characterization. In a first implementation, two graphene layers gate each other, thereby behaving as a controllable single equivalent layer but without any additional gating structure. Second, we show that adding an additional gate --a third graphene layer or an external gate-- allows independent control of the complex conductivity of each layer within the stack and hence provides enhanced control on the stack equivalent complex conductivity. The proposed concepts are first theoretically studied and then demonstrated experimentally via a detailed procedure allowing extraction of the parameters of each layer independently and for arbitrary pre-do**. These results are believed to be instrumental to the development of THz and mid-IR plasmonic devices with enhanced performance and reconfiguration capabilities.
△ Less
Submitted 2 March, 2015; v1 submitted 13 May, 2014;
originally announced May 2014.
-
MEMS-reconfigurable metamaterials and antenna applications
Authors:
Tomislav Debogovic,
Julien Perruisseau-Carrier
Abstract:
This paper reviews some of our contributions to reconfigurable metamaterials, where dynamic control is enabled by micro-electro-mechanical systems (MEMS) technology. First, we show reconfigurable composite right/left handed transmission lines (CRLH-TLs) having state of the art phase velocity variation and loss, thereby enabling efficient reconfigurable phase shifters and leaky-wave antennas (LWA).…
▽ More
This paper reviews some of our contributions to reconfigurable metamaterials, where dynamic control is enabled by micro-electro-mechanical systems (MEMS) technology. First, we show reconfigurable composite right/left handed transmission lines (CRLH-TLs) having state of the art phase velocity variation and loss, thereby enabling efficient reconfigurable phase shifters and leaky-wave antennas (LWA). Second, we present very low loss metasurface designs with reconfigurable reflection properties, applicable in reflectarrays and partially reflective surface (PRS) antennas. All the presented devices have been fabricated and experimentally validated. They operate in X- and Ku-bands.
△ Less
Submitted 7 May, 2014; v1 submitted 14 April, 2014;
originally announced April 2014.
-
Predicting input impedance and efficiency of graphene reconfigurable dipoles using a simple circuit model
Authors:
Michele Tamagnone,
Julien Perruisseau-Carrier
Abstract:
An analytical circuit model able to predict the input impedance of reconfigurable graphene plasmonic dipoles is presented. A suitable definition of plasmonic characteristic impedance, employing natural currents, is used to for consistent modeling of the antenna-load connection in the circuit. In its purely analytical form, the model shows good agreement with full-wave simulations, and explains the…
▽ More
An analytical circuit model able to predict the input impedance of reconfigurable graphene plasmonic dipoles is presented. A suitable definition of plasmonic characteristic impedance, employing natural currents, is used to for consistent modeling of the antenna-load connection in the circuit. In its purely analytical form, the model shows good agreement with full-wave simulations, and explains the remarkable tuning properties of graphene antennas. Furthermore, using a single full-wave simulation and scaling laws, additional parasitic elements can be determined for a vast parametric space, leading to very accurate modeling. Finally, we also show that the modeling approach allows fair estimation of radiation efficiency as well. The approach also applies to thin plasmonic antennas realized using noble metals or semiconductors.
△ Less
Submitted 6 February, 2014;
originally announced February 2014.
-
Efficient MIMO Transmission of PSK Signals With a Single-Radio Reconfigurable Antenna
Authors:
Mohsen Yousefbeiki,
Osama N. Alrabadi,
Julien Perruisseau-Carrier
Abstract:
Crucial developments to the recently introduced signal-space approach for multiplexing multiple data symbols using a single-radio switched antenna are presented. First, we introduce a general framework for expressing the spatial multiplexing relation of the transmit signals only from the antenna scattering parameters and the modulating reactive loading. This not only avoids tedious far-field calcu…
▽ More
Crucial developments to the recently introduced signal-space approach for multiplexing multiple data symbols using a single-radio switched antenna are presented. First, we introduce a general framework for expressing the spatial multiplexing relation of the transmit signals only from the antenna scattering parameters and the modulating reactive loading. This not only avoids tedious far-field calculations, but more importantly provides an efficient and practical strategy for spatially multiplexing PSK signals of any modulation order. The proposed approach allows ensuring a constant impedance matching at the input of the driving antenna for all symbol combinations, and as importantly uses only passive reconfigurable loads. This obviates the use of reconfigurable matching networks and active loads, respectively, thereby overcoming stringent limitations of previous single-feed MIMO techniques in terms of complexity, efficiency, and power consumption. The proposed approach is illustrated by the design of a realistic very compact antenna system optimized for multiplexing QPSK signals. The results show that the proposed approach can bring the MIMO benefits to the low-end user terminals at a reduced RF complexity.
△ Less
Submitted 5 February, 2014;
originally announced February 2014.
-
Copper and Transparent-Conductor Reflectarray Elements on Thin-Film Solar Cell Panels
Authors:
Philippe Dreyer,
Monica Morales-Masis,
Sylvain Nicolay,
Christophe Ballif,
Julien Perruisseau-Carrier
Abstract:
This work addresses the integration of reflectarray antennas (RA) on thin film Solar Cell (SC) panels, as a mean to save real estate, weight, or cost in platforms such as satellites or transportable autonomous antenna systems. Our goal is to design a good RA unit cell in terms of phase response and bandwidth, while simultaneously achieving high optical transparency and low microwave loss, to prese…
▽ More
This work addresses the integration of reflectarray antennas (RA) on thin film Solar Cell (SC) panels, as a mean to save real estate, weight, or cost in platforms such as satellites or transportable autonomous antenna systems. Our goal is to design a good RA unit cell in terms of phase response and bandwidth, while simultaneously achieving high optical transparency and low microwave loss, to preserve good SC and RA energy efficiencies, respectively. Since there is a trade-off between the optical transparency and microwave surface conductivity of a conductor, here both standard copper and transparent conductors are considered. The results obtained at the unit cell level demonstrates the feasibility of integrating RA on a thin-film SC, preserving for the first time good performance in terms of both SC and RA efficiency. For instance, measurement at X-band demonstrate families of cells providing a phase range larger than 270° with average microwave loss of -2.45dB (resp. -0.25dB) and average optical transparency in the visible spectrum of 90% (resp. 85%) using transparent conductive multilayer (resp. a copper layer).
△ Less
Submitted 19 November, 2013;
originally announced November 2013.
-
User Effects in Beam-Space MIMO
Authors:
Mohsen Yousefbeiki,
Halima Najibi,
Julien Perruisseau-Carrier
Abstract:
The performance and design of the novel single-RF-chain beam-space MIMO antenna concept is evaluated for the first time in the presence of the user. First, the variations of different performance parameters are evaluated when placing a beam-space MIMO antenna in close proximity to the user body in several typical operating scenarios. In addition to the typical degradation of conventional antennas…
▽ More
The performance and design of the novel single-RF-chain beam-space MIMO antenna concept is evaluated for the first time in the presence of the user. First, the variations of different performance parameters are evaluated when placing a beam-space MIMO antenna in close proximity to the user body in several typical operating scenarios. In addition to the typical degradation of conventional antennas in terms of radiation efficiency and impedance matching, it is observed that the user body corrupts the power balance and the orthogonality of the beam-space MIMO basis. However, capacity analyses show that throughput reduction mainly stems from the absorption in user body tissues rather than from the power imbalance and the correlation of the basis. These results confirm that the beam-space MIMO concept, so far only demonstrated in the absence of external perturbation, still performs very well in typical human body interaction scenarios.
△ Less
Submitted 6 February, 2014; v1 submitted 30 October, 2013;
originally announced October 2013.
-
Reconfigurable Reflectarrays and Array Lenses for Dynamic Antenna Beam Control: A Review
Authors:
Sean Victor Hum,
Julien Perruisseau-Carrier
Abstract:
Advances in reflectarrays and array lenses with electronic beam-forming capabilities are enabling a host of new possibilities for these high-performance, low-cost antenna architectures. This paper reviews enabling technologies and topologies of reconfigurable reflectarray and array lens designs, and surveys a range of experimental implementations and achievements that have been made in this area i…
▽ More
Advances in reflectarrays and array lenses with electronic beam-forming capabilities are enabling a host of new possibilities for these high-performance, low-cost antenna architectures. This paper reviews enabling technologies and topologies of reconfigurable reflectarray and array lens designs, and surveys a range of experimental implementations and achievements that have been made in this area in recent years. The paper describes the fundamental design approaches employed in realizing reconfigurable designs, and explores advanced capabilities of these nascent architectures, such as multi-band operation, polarization manipulation, frequency agility, and amplification. Finally, the paper concludes by discussing future challenges and possibilities for these antennas.
△ Less
Submitted 21 August, 2013;
originally announced August 2013.
-
Fundamental limits and near-optimal design of graphene modulators and non-reciprocal devices
Authors:
Michele Tamagnone,
Arya Fallahi,
Juan R. Mosig,
Julien Perruisseau-Carrier
Abstract:
The potential of graphene for use in photonic applications was evidenced by recent demonstrations of modulators, polarisation rotators, and isolators. These promising yet preliminary results raise crucial questions: what is the optimal performance achievable by more complex designs using multilayer structures, graphene patterning, metal additions, or a combination of these approaches, and how can…
▽ More
The potential of graphene for use in photonic applications was evidenced by recent demonstrations of modulators, polarisation rotators, and isolators. These promising yet preliminary results raise crucial questions: what is the optimal performance achievable by more complex designs using multilayer structures, graphene patterning, metal additions, or a combination of these approaches, and how can this optimum design be achieved in practice? Today, the complexity of the problem, which is magnified by the variability in graphene parameters, leaves the design of these new devices to time-consuming and suboptimal trial-and-error procedures. We address this issue by first demonstrating that the relevant figures of merit for the devices above are subject to absolute theoretical upper bounds. Strikingly these limits are related only to the conductivity tensor of graphene; thus, we can provide essential roadmap information such as the best possible device performance versus wavelength and graphene quality. Second, based on the theory developed, physical insight, and detailed simulations, we demonstrate how structures closely approaching these fundamental limits can be designed, demonstrating the possibility of significant improvement. These results are believed to be of paramount importance for the design of graphene-based modulators, rotators, and isolators and are also directly applicable to other 2-dimensional materials.
△ Less
Submitted 22 August, 2013; v1 submitted 14 August, 2013;
originally announced August 2013.
-
Towards Compact and Frequency-Tunable Antenna Solutions for MIMO Transmission with a Single RF Chain
Authors:
Mohsen Yousefbeiki,
Julien Perruisseau-Carrier
Abstract:
Recently, a technique called beam-space MIMO has been demonstrated as an effective approach for transmitting multiple signals while using a single RF-chain. In this work, we present novel design considerations and a compact antenna solution to stimulate the deployment of beam-space MIMO in future wireless applications. Targeting integration in small wireless devices, the novel antenna is made of a…
▽ More
Recently, a technique called beam-space MIMO has been demonstrated as an effective approach for transmitting multiple signals while using a single RF-chain. In this work, we present novel design considerations and a compact antenna solution to stimulate the deployment of beam-space MIMO in future wireless applications. Targeting integration in small wireless devices, the novel antenna is made of a single integrated radiator rather than an array of physically-separated dipoles. It also drastically simplifies the implementation of variable loads and DC bias circuits for BPSK modulated signals, and does not require any external reconfigurable matching circuit. Finally, we show that this antenna system could be reconfigured by dynamic adjustment of terminating loads to preserve its beam-space multiplexing capabilities over a 1:2 tuning range, thereby promoting the convergence of MIMO and dynamic spectrum allocation via reduced-complexity hardware. A prototype achieving single-RF-chain multiplexing at a fixed frequency is designed and measured, showing excellent agreement between simulations and measurements.
△ Less
Submitted 19 June, 2013;
originally announced June 2013.
-
Integral Equation Analysis of Plane Wave Scattering by Coplanar Graphene-Strip Gratings in the THz Range
Authors:
Olga V. Shapoval,
Juan Sebastian Gomez-Diaz,
Julien Perruisseau-Carrier,
Juan R. Mosig,
Alexander I. Nosich
Abstract:
The plane wave scattering and absorption by finite and infinite gratings of free-space standing infinitely long graphene strips are studied in the THz range. A novel numerical approach, based on graphene surface impedance, hyper-singular integral equations, and the Nystrom method, is proposed. This technique guarantees fast convergence and controlled accuracy of computations. Reflectance, transmit…
▽ More
The plane wave scattering and absorption by finite and infinite gratings of free-space standing infinitely long graphene strips are studied in the THz range. A novel numerical approach, based on graphene surface impedance, hyper-singular integral equations, and the Nystrom method, is proposed. This technique guarantees fast convergence and controlled accuracy of computations. Reflectance, transmittance, and absorbance are carefully studied as a function of graphene and grating parameters, revealing the presence of surface plasmon resonances. Specifically, larger graphene relaxation times increases the number of resonances in the THz range, leading to higher wave transmittance due to the reduced losses; on the other hand an increase of graphene chemical potential up-shifts the frequency of plasmon resonances. It is also shown that a relatively low number of graphene strips (>10) are able to reproduce Rayleigh anomalies. These features make graphene strips good candidates for many applications, including tunable absorbers and frequency selective surfaces.
△ Less
Submitted 22 May, 2013;
originally announced May 2013.
-
Sinusoidally-Modulated Graphene Leaky-Wave Antenna for Electronic Beamscanning at THz
Authors:
Marc Esquius-Morote,
Juan Sebastian Gomez-Diaz,
Julien Perruisseau-Carrier
Abstract:
This paper proposes the concept, analysis and design of a sinusoidally-modulated graphene leaky-wave antenna with beam scanning capabilities at a fixed frequency. The antenna operates at terahertz frequencies and is composed of a graphene sheet transferred onto a back-metallized substrate and a set of polysilicon DC gating pads located beneath it. In order to create a leaky-mode, the graphene surf…
▽ More
This paper proposes the concept, analysis and design of a sinusoidally-modulated graphene leaky-wave antenna with beam scanning capabilities at a fixed frequency. The antenna operates at terahertz frequencies and is composed of a graphene sheet transferred onto a back-metallized substrate and a set of polysilicon DC gating pads located beneath it. In order to create a leaky-mode, the graphene surface reactance is sinusoidally-modulated via graphene's field effect by applying adequate DC bias voltages to the different gating pads. The pointing angle and leakage rate can be dynamically controlled by adjusting the applied voltages, providing versatile beamscanning capabilities. The proposed concept and achieved performance, computed using realistic material parameters, are extremely promising for beamscanning at THz frequencies, and could pave the way to graphene-based reconfigurable transceivers and sensors.
△ Less
Submitted 20 January, 2014; v1 submitted 21 May, 2013;
originally announced May 2013.
-
Graphene Based Plasmonic Tunable Low Pass Filters in the THz Band
Authors:
D. Correas Serrano,
J. S. Gomez Diaz,
J. Perruisseau-Carrier,
A. Alvarez Melcon
Abstract:
We propose the concept, synthesis, analysis, and design of graphene-based plasmonic tunable low-pass filters operating in the THz band. The proposed structure is composed of a graphene strip transferred onto a dielectric and a set of polysilicon DC gating pads located beneath it. This structure implements a stepped impedance low-pass filter for the propagating surface plasmons by adequately contro…
▽ More
We propose the concept, synthesis, analysis, and design of graphene-based plasmonic tunable low-pass filters operating in the THz band. The proposed structure is composed of a graphene strip transferred onto a dielectric and a set of polysilicon DC gating pads located beneath it. This structure implements a stepped impedance low-pass filter for the propagating surface plasmons by adequately controlling the guiding properties of each strip section through graphene's field effect. A synthesis procedure is presented to design filters with desired specifications in terms of cut-off frequency, in-band performance, and rejection characteristics. The electromagnetic modeling of the structure is efficiently performed by combining an electrostatic scaling law to compute the guiding features of each strip section with a transmission line and transfer-matrix framework, approach further validated via full wave simulations. The performance of the proposed filters is evaluated in practical scenarios, taking into account the presence of the gating bias and the influence of graphene's losses. These results, together with the high miniaturization associated with plasmonic propagation, are very promising for the future use and integration of the proposed filters with other graphene and silicon-based elements in innovative THz communication systems.
△ Less
Submitted 25 October, 2014; v1 submitted 23 April, 2013;
originally announced April 2013.
-
Graphene Antennas: Can Integration and Reconfigurability Compensate for the Loss?
Authors:
Julien Perruisseau-Carrier,
Michele Tamagnone,
Juan Sebastian Gomez-Diaz,
Eduardo Carrasco
Abstract:
In this opening presentation we will first recall the main characteristics of graphene conductivity and electromagnetic wave propagation on graphene-based structures. Based on these observations and different graphene antenna simulations from microwave to Terahertz, we will discuss the issue of antenna efficiency, integration and reconfigurability, as function of the operation frequency range. Whi…
▽ More
In this opening presentation we will first recall the main characteristics of graphene conductivity and electromagnetic wave propagation on graphene-based structures. Based on these observations and different graphene antenna simulations from microwave to Terahertz, we will discuss the issue of antenna efficiency, integration and reconfigurability, as function of the operation frequency range. While the applicability of graphene for antennas at microwave appears limited to particular cases where very low efficiency can be tolerated for integration or transparency purpose, the plasmonic nature of graphene conductivity at terahertz frequency allows unprecedented antenna properties and in particular efficient dynamic reconfiguration.
△ Less
Submitted 26 May, 2013; v1 submitted 16 April, 2013;
originally announced April 2013.
-
Further Comment on 'Encoding many channels on the same frequency through radio vorticity: first experimental test'
Authors:
Michele Tamagnone,
Christophe Craeye,
Julien Perruisseau-Carrier
Abstract:
We show that the reply by Tamburini et al (2012 New J. Phys. 14 118002) to our previous comment (2012 New J. Phys. 14 118001) on the experiment reported in (2012 New J. Phys. 14 033001) actually does not invalidate any of the issues raised in our initial comment.
We show that the reply by Tamburini et al (2012 New J. Phys. 14 118002) to our previous comment (2012 New J. Phys. 14 118001) on the experiment reported in (2012 New J. Phys. 14 033001) actually does not invalidate any of the issues raised in our initial comment.
△ Less
Submitted 30 July, 2013; v1 submitted 17 February, 2013;
originally announced February 2013.
-
Graphene-based plasmonic switches at near infrared frequencies
Authors:
J. S. Gomez-Diaz,
J. Perruisseau-Carrier
Abstract:
The concept, analysis, and design of series switches for graphene-strip plasmonic waveguides at near infrared frequencies are presented. Switching is achieved by using graphene's field effect to selectively enable or forbid propagation on a section of the graphene strip waveguide, thereby allowing good transmission or high isolation, respectively. The electromagnetic modeling of the proposed struc…
▽ More
The concept, analysis, and design of series switches for graphene-strip plasmonic waveguides at near infrared frequencies are presented. Switching is achieved by using graphene's field effect to selectively enable or forbid propagation on a section of the graphene strip waveguide, thereby allowing good transmission or high isolation, respectively. The electromagnetic modeling of the proposed structure is performed using full-wave simulations and a transmission line model combined with a matrix-transfer approach, which takes into account the characteristics of the plasmons supported by the different graphene-strip waveguide sections of the device. The performance of the switch is evaluated versus different parameters of the structure, including surrounding dielectric media, electrostatic gating and waveguide dimensions.
△ Less
Submitted 2 September, 2013; v1 submitted 4 February, 2013;
originally announced February 2013.
-
Effect of Spatial Dispersion on Surface Waves Propagating Along Graphene Sheets
Authors:
J. S. Gomez-Diaz,
J. R. Mosig,
J. Perruisseau-Carrier
Abstract:
We investigate the propagation of surface waves along a spatially dispersive graphene sheet, including substrate effects. The proposed analysis derives the admittances of an equivalent circuit of graphene able to handle spatial dispersion, using a non-local model of graphene conductivity. Similar to frequency selective surfaces, the analytical admittances depend on the propagation constant of the…
▽ More
We investigate the propagation of surface waves along a spatially dispersive graphene sheet, including substrate effects. The proposed analysis derives the admittances of an equivalent circuit of graphene able to handle spatial dispersion, using a non-local model of graphene conductivity. Similar to frequency selective surfaces, the analytical admittances depend on the propagation constant of the waves traveling along the sheet. Dispersion relations for the supported TE and TM modes are then obtained by applying a transverse resonance equation. Application of the method demonstrates that spatial dispersion can dramatically affect the propagation of surface plasmons, notably modifying their mode confinement and increasing losses, even at frequencies where intraband transitions are the dominant contribution to graphene conductivity. These results show the need for correctly assessing spatial dispersion effects in the development of plasmonic devices at the low THz band.
△ Less
Submitted 2 September, 2013; v1 submitted 7 January, 2013;
originally announced January 2013.
-
Tunable Graphene Reflective Cells for THz Reflectarrays and Generalized Law of Reflection
Authors:
Eduardo Carrasco,
Michele Tamagnone,
Julien Perruisseau-Carrier
Abstract:
A tunable graphene-based reflective cell operating at THz is proposed for use in reconfigurable-beam reflectarrays, or similarly to implement the so-called generalized law of reflection. The change in the complex conductivity of graphene when biased by an electric field allows controlling the phase of the reflected field at each element of the array. Additionally, the slow wave propagation support…
▽ More
A tunable graphene-based reflective cell operating at THz is proposed for use in reconfigurable-beam reflectarrays, or similarly to implement the so-called generalized law of reflection. The change in the complex conductivity of graphene when biased by an electric field allows controlling the phase of the reflected field at each element of the array. Additionally, the slow wave propagation supported by graphene drastically reduces the dimensions of the cell, which allows smaller inter-element spacing hence better array performance. An elementary cell is optimized and its scattering parameters computed, demonstrating a dynamic phase range of 300 degrees and good loss figure for realistic chemical potential variations. Finally, a circuit model is proposed and shown to very accurately predict the element response.
△ Less
Submitted 13 December, 2012;
originally announced December 2012.
-
Manipulation of Giant Faraday Rotation in Graphene Metasurfaces
Authors:
Arya Fallahi,
Julien Perruisseau-Carrier
Abstract:
Faraday rotation is a fundamental magneto-optical phenomenon used in various optical control and magnetic field sensing techniques. Recently, it was shown that a giant Faraday rotation can be achieved in the low-THz regime by a single monoatomic graphene layer. Here, we demonstrate that this exceptional property can be manipulated through adequate nano-patterning, notably achieving giant rotation…
▽ More
Faraday rotation is a fundamental magneto-optical phenomenon used in various optical control and magnetic field sensing techniques. Recently, it was shown that a giant Faraday rotation can be achieved in the low-THz regime by a single monoatomic graphene layer. Here, we demonstrate that this exceptional property can be manipulated through adequate nano-patterning, notably achieving giant rotation up to 6THz with features no smaller than 100nm. The effect of the periodic patterning on the Faraday rotation is predicted by a simple physical model, which is then verified and refined through accurate full-wave simulations.
△ Less
Submitted 2 November, 2012;
originally announced November 2012.
-
Reconfigurable THz Plasmonic Antenna Concept Using a Graphene Stack
Authors:
Michele Tamagnone,
Juan Sebastian Gomez Diaz,
Juan Ramon Mosig,
Julien Perruisseau-Carrier
Abstract:
The concept and analysis of a Terahertz (THz) frequency-reconfigurable antenna using graphene are presented. The antenna exploits dipole-like plasmonic resonances that can be frequency-tuned on large range via the electric field effect in a graphene stack. In addition to efficient dynamic control, the proposed approach allows high miniaturization and good direct matching with continuous wave THz s…
▽ More
The concept and analysis of a Terahertz (THz) frequency-reconfigurable antenna using graphene are presented. The antenna exploits dipole-like plasmonic resonances that can be frequency-tuned on large range via the electric field effect in a graphene stack. In addition to efficient dynamic control, the proposed approach allows high miniaturization and good direct matching with continuous wave THz sources. A qualitative model is used to explain the excellent impedance stability under reconfiguration. These initial results are very promising for future all-graphene THz transceivers and sensors. Keywords: Reconfigurable antenna, Graphene, Plasmons, Terahertz, frequency-tuning.
△ Less
Submitted 6 February, 2014; v1 submitted 30 October, 2012;
originally announced October 2012.
-
Design of Tunable Biperiodic Graphene Metasurfaces
Authors:
Arya Fallahi,
Julien Perruisseau-Carrier
Abstract:
Periodic structures with subwavelength features are instrumental in the versatile and effective control of electromagnetic waves from radio frequencies up to optics. In this paper, we theoretically evaluate the potential applications and performance of electromagnetic metasurfaces made of periodically patterned graphene. Several graphene metasurfaces are presented, thereby demonstrating that such…
▽ More
Periodic structures with subwavelength features are instrumental in the versatile and effective control of electromagnetic waves from radio frequencies up to optics. In this paper, we theoretically evaluate the potential applications and performance of electromagnetic metasurfaces made of periodically patterned graphene. Several graphene metasurfaces are presented, thereby demonstrating that such ultrathin surfaces can be used to dynamically control the electromagnetic wave reflection, absorption, or polarization. Indeed, owing to the graphene properties, the structure performance in terms of resonance frequencies and bandwidths changes with the variation of electrostatic bias fields. To demonstrate the applicability of the concept at different frequency ranges, the examples provided range from microwave to infrared, corresponding to graphene features with length-scales of a few millimeters down to about a micrometer, respectively. The results are obtained using a full-vector semianalytical numerical technique developed to accurately model the graphene-based multilayer periodic structures under study.
△ Less
Submitted 20 October, 2012;
originally announced October 2012.
-
Comment on 'Encoding many channels on the same frequency through radio vorticity: first experimental test'
Authors:
Michele Tamagnone,
Christophe Craeye,
Julien Perruisseau-Carrier
Abstract:
We show that the public experiment held in Venice by F. Tamburini et al and reported in (2012 New J. Phys. 14 033001) can be regarded as a particular implementation of Multiple-Input Multiple-Output (MIMO) communications, hence bringing no advantages with respect to known techniques. Moreover, we explain that the use of a 'vortex' mode (orbital angular momentum OAM l = 1) at one of the transmit an…
▽ More
We show that the public experiment held in Venice by F. Tamburini et al and reported in (2012 New J. Phys. 14 033001) can be regarded as a particular implementation of Multiple-Input Multiple-Output (MIMO) communications, hence bringing no advantages with respect to known techniques. Moreover, we explain that the use of a 'vortex' mode (orbital angular momentum OAM l = 1) at one of the transmit antennas is not necessary to encode different channels since only different patterns -or similarly different pointing angles- of the transmit antennas are required. Finally, we identify why this MIMO transmission allowed decoding of two signals despite being line-of-sight. This is due to the large separation between the receiving antennas, which places the transmit antennas in the near-field Fresnel region of the receiving 'array'. This strongly limits the application of this technique in practice, since, for a fixed separation between receiving antennas, the detectable signal power from any additional vortex mode decays at least as 1/r^4.
△ Less
Submitted 19 October, 2012;
originally announced October 2012.
-
Polarimetric Control of Reflective Metasurfaces
Authors:
Xavier Artiga,
Daniele Bresciani,
Hervé Legay,
Julien Perruisseau-Carrier
Abstract:
This letter addresses the synthesis of reflective cells approaching a given desired Floquet's scattering matrix. This work is motivated by the need to obtain much finer control of reflective metasurfaces by controlling not only their co-polarized reflection but also their cross-coupling behavior. The demonstrated capability will enable more powerful design approaches -involving all field component…
▽ More
This letter addresses the synthesis of reflective cells approaching a given desired Floquet's scattering matrix. This work is motivated by the need to obtain much finer control of reflective metasurfaces by controlling not only their co-polarized reflection but also their cross-coupling behavior. The demonstrated capability will enable more powerful design approaches -involving all field components in phase and magnitude- and consequently better performance in applications involving reflective metasurfaces. We first expose some fundamental theoretical constraints on the cell scattering parameters. Then, a successful procedure for controlling all four scattering parameters by applying parallelogram and trapezoid transformations to square patches is presented, considering both normal and oblique incidence.
△ Less
Submitted 17 October, 2012;
originally announced October 2012.
-
Graphene for Antenna Applications: Opportunities and Challenges from Microwaves to THz
Authors:
Julien Perruisseau-Carrier
Abstract:
The use of graphene for antennas and other electromagnetic passives could bring significant benefit such as extreme miniaturization, monolithic integration with graphene RF nanoelectronics, efficient dynamic tuning, and even transparency and mechanical flexibility. Though recently different related theoretical works have been presented, relatively few applications have been proposed and realistica…
▽ More
The use of graphene for antennas and other electromagnetic passives could bring significant benefit such as extreme miniaturization, monolithic integration with graphene RF nanoelectronics, efficient dynamic tuning, and even transparency and mechanical flexibility. Though recently different related theoretical works have been presented, relatively few applications have been proposed and realistically assessed. In this invited talk we will briefly review the main properties of graphene and the state of the art in its theoretical and experimental characterization. Then, we will discuss a number of potential antenna applications from microwave to THz, providing in each case a critical assessment of the benefits, limitations, and remaining issues towards actual real-life implementations. Here we provide a brief overview of different devices and associated developments in our group discussed in the talk, including graphene antennas and reflectarrays at microwave and THz, plasmonic switches, isotropic and anisotropic meta-surfaces, or graphene RF-NEMS.
△ Less
Submitted 12 October, 2012;
originally announced October 2012.
