Showing 1–9 of 9 results for author: Ortolano, M

Good practice guide on the graphene-based AC-QHE realization of the farad

Authors: Luca Callegaro, Stephan Bauer, Blaise Jeanneret, Mattias Kruskopf, Martina Marzano, Massimo Ortolano, Frederic Overney

Abstract: This Good Practice Guide provides information for the realization of the farad from the quantum Hall resistance in graphene devices by using digital impedance bridges. The fabrication and characterization of graphene quantum Hall effect devices, the cryogenic environment required to achieve the quantization conditions, the digital impedance bridges and calibration procedures are reported. The gu… ▽ More This Good Practice Guide provides information for the realization of the farad from the quantum Hall resistance in graphene devices by using digital impedance bridges. The fabrication and characterization of graphene quantum Hall effect devices, the cryogenic environment required to achieve the quantization conditions, the digital impedance bridges and calibration procedures are reported. The guide is a deliverable of the Joint Research Project EMPIR 18SIB07 GIQS: Graphene Impedance Quantum Standard. This project received funding from the European Metrology Programme for Innovation and Research (EMPIR) co-financed by the Participating States and from the European Unions' Horizon 2020 research and innovation programme. Funder ID: 10.13039/100014132 , Grant no: 18SIB07. △ Less

Submitted 10 May, 2022; originally announced May 2022.

Comments: 49 pages, 20 figures

Nonconventional Quantized Hall Resistances Obtained with $ν= 2$ Equilibration in Epitaxial Graphene $p-n$ Junctions

Authors: Albert F. Rigosi, Dinesh Patel, Martina Marzano, Mattias Kruskopf, Heather M. Hill, Hanbyul **, Jiuning Hu, Angela R. Hight Walker, Massimo Ortolano, Luca Callegaro, Chi-Te Liang, David B. Newell

Abstract: We have demonstrated the millimeter-scale fabrication of monolayer epitaxial graphene $p-n$ junction devices using simple ultraviolet photolithography, thereby significantly reducing device processing time compared to that of electron beam lithography typically used for obtaining sharp junctions. This work presents measurements yielding nonconventional, fractional multiples of the typical quantize… ▽ More We have demonstrated the millimeter-scale fabrication of monolayer epitaxial graphene $p-n$ junction devices using simple ultraviolet photolithography, thereby significantly reducing device processing time compared to that of electron beam lithography typically used for obtaining sharp junctions. This work presents measurements yielding nonconventional, fractional multiples of the typical quantized Hall resistance at $ν=2$ ($R_H\approx 12906 Ω$) that take the form: $\frac{a}{b}R_H$. Here, $a$ and $b$ have been observed to take on values such 1, 2, 3, and 5 to form various coefficients of $R_H$. Additionally, we provide a framework for exploring future device configurations using the LTspice circuit simulator as a guide to understand the abundance of available fractions one may be able to measure. These results support the potential for drastically simplifying device processing time and may be used for many other two-dimensional materials. △ Less

Submitted 24 January, 2022; originally announced January 2022.

Circuit models and SPICE macro-models for quantum Hall effect devices

Authors: Massimo Ortolano, Luca Callegaro

Abstract: Quantum Hall effect (QHE) devices are a pillar of modern quantum electrical metrology. Electrical networks including one or more QHE elements can be used as quantum resistance and impedance standards. The analysis of these networks allows metrologists to evaluate the effect of the inevitable parasitic parameters on their performance as standards. This paper presents a systematic analysis of the va… ▽ More Quantum Hall effect (QHE) devices are a pillar of modern quantum electrical metrology. Electrical networks including one or more QHE elements can be used as quantum resistance and impedance standards. The analysis of these networks allows metrologists to evaluate the effect of the inevitable parasitic parameters on their performance as standards. This paper presents a systematic analysis of the various circuit models for QHE elements proposed in the literature, and the development of a new model. This last model is particularly suited to be employed with the analogue electronic circuit simulator SPICE. The SPICE macro-model and examples of SPICE simulations, validated by comparison with the corresponding analytical solution and/or experimental data, are provided. △ Less

Submitted 14 January, 2015; originally announced January 2015.

A three-arm current comparator bridge, for impedance comparisons over the complex plane

Authors: Luca Callegaro, Vincenzo D'Elia, Massimo Ortolano, Faranak Pourdanesh

Abstract: We present here the concept of three-arm current comparator impedance bridge, which allows comparisons among three unlike impedances. Its purpose is the calibration of impedances having arbitrary phase angles, against calibrated nearly-pure impedances. An analysis of the bridge optimal setting and proper operation is presented. To test the concept, a two terminal-pair digitally-assisted bridge has… ▽ More We present here the concept of three-arm current comparator impedance bridge, which allows comparisons among three unlike impedances. Its purpose is the calibration of impedances having arbitrary phase angles, against calibrated nearly-pure impedances. An analysis of the bridge optimal setting and proper operation is presented. To test the concept, a two terminal-pair digitally-assisted bridge has been realized; measurements of an air-core inductor and of an RC network versus decade resistance and capacitance standards, at kHz frequency, have been performed. The bridge measurements are compatible with previous knowledge of the standards' values with relative deviations in the 10^-5 -- 10^-6 range. △ Less

Submitted 18 August, 2014; originally announced August 2014.

Experiences with a two terminal-pair digital impedance bridge

Authors: Luca Callegaro, Vincenzo D'Elia, Marian Kampik, Dan Bee Kim, Massimo Ortolano, Faranak Pourdanesh

Abstract: This paper describes the realization of a two terminal-pair digital impedance bridge and the test measurements performed with it. The bridge, with a very simple architecture, is based on a commercial two-channel digital signal synthesizer and a synchronous detector. The bridge can perform comparisons between impedances having arbitrary phase and magnitude ratio: its balance is achieved automatical… ▽ More This paper describes the realization of a two terminal-pair digital impedance bridge and the test measurements performed with it. The bridge, with a very simple architecture, is based on a commercial two-channel digital signal synthesizer and a synchronous detector. The bridge can perform comparisons between impedances having arbitrary phase and magnitude ratio: its balance is achieved automatically in less than a minute. $R$-$C$ comparisons with calibrated standards, at kHz frequency and 100 kohm magnitude level, give ratio errors of the order of $10^{-6}$, with potential for further improvements. △ Less

Submitted 12 August, 2014; originally announced August 2014.

On the synthesis of Quantum Hall Array Resistance Standards

Authors: Massimo Ortolano, Marco Abrate, Luca Callegaro

Abstract: Quantum Hall effect (QHE) is the basis of modern resistance metrology. In Quantum Hall Array Resistance Standards (QHARS), several individual QHE elements, each one having the same QHE resistance (typically half of the von Klitzing constant), are arranged in networks that realize resistance values close to decadic values (such as 1 kiloohm or 100 kiloohm), of direct interest for dissemination. The… ▽ More Quantum Hall effect (QHE) is the basis of modern resistance metrology. In Quantum Hall Array Resistance Standards (QHARS), several individual QHE elements, each one having the same QHE resistance (typically half of the von Klitzing constant), are arranged in networks that realize resistance values close to decadic values (such as 1 kiloohm or 100 kiloohm), of direct interest for dissemination. The same decadic value can be approximated with different grades of precision, and even for the same approximation several networks of QHE elements can be conceived. The paper investigates the design of QHARS networks by giving methods to find a proper approximation of the resistance of interest, and to design the corresponding network with a small number of elements. Results for several decadic cases are given. △ Less

Submitted 4 November, 2013; originally announced November 2013.

Bridge connection of quantum Hall elementary devices

Authors: Luca Callegaro, Massimo Ortolano

Abstract: Multiple-series and multiple-parallel connections of quantum Hall elementary devices allow the realization of multiple or fractional values of the quantized Hall resistance, rejecting the effect of contact and wiring resistances. We introduce here the multiple-bridge connection, which maintains the properties of multiple-series and parallel connections and allows more freedom in the choice of the… ▽ More Multiple-series and multiple-parallel connections of quantum Hall elementary devices allow the realization of multiple or fractional values of the quantized Hall resistance, rejecting the effect of contact and wiring resistances. We introduce here the multiple-bridge connection, which maintains the properties of multiple-series and parallel connections and allows more freedom in the choice of the topology of networks composed of quantum Hall elements, and the design of more efficient quantum Hall array resistance standards (and other devices). As an example, a 5-element network is analyzed in detail. △ Less

Submitted 21 October, 2013; originally announced October 2013.

Matrix method analysis of quantum Hall effect device connections

Authors: Massimo Ortolano, Luca Callegaro

Abstract: The modelling of electrical connections of single, or several, multiterminal quantum Hall effect (QHE) devices is relevant for electrical metrology: it is known, in fact, that certain particular connections allow i) the realization of multiples or fractions of the quantised resistance, or ii) the rejection of stray impedances, so that the configuration maintains the status of quantum standard. Ric… ▽ More The modelling of electrical connections of single, or several, multiterminal quantum Hall effect (QHE) devices is relevant for electrical metrology: it is known, in fact, that certain particular connections allow i) the realization of multiples or fractions of the quantised resistance, or ii) the rejection of stray impedances, so that the configuration maintains the status of quantum standard. Ricketts-Kemeny and Delahaye equivalent circuits are known to be accurate models of the QHE: however, the numerical or analytical solution of electrical networks including these equivalent circuits can be difficult. In this paper, we introduce a method of analysis based on the representation of a QHE device by means of the \emph{indefinite admittance matrix}: external connections are then represented with another matrix, easily written by inspection. Some examples, including the solution of double- and triple-series connections, are shown. △ Less

Submitted 12 July, 2011; originally announced July 2011.

Systematic errors in the correlation method for Johnson noise thermometry: residual correlations due to amplifiers

Authors: Luca Callegaro, Marco Pisani, Massimo Ortolano

Abstract: Johnson noise thermometers (JNT) measure the equilibrium electrical noise, proportional to thermodynamic temperature, of a sensing resistor. In the correlation method, the same resistor is connected to two amplifiers and a correlation of their outputs is performed, in order to reject amplifiers' noise. Such rejection is not perfect: the residual correlation gives a systematic error in the JNT re… ▽ More Johnson noise thermometers (JNT) measure the equilibrium electrical noise, proportional to thermodynamic temperature, of a sensing resistor. In the correlation method, the same resistor is connected to two amplifiers and a correlation of their outputs is performed, in order to reject amplifiers' noise. Such rejection is not perfect: the residual correlation gives a systematic error in the JNT reading. In order to put an upper limit, or to achieve a correction, for such error, a careful electrical modelling of the amplifiers and connections must be performed. Standard numerical simulation tools are inadequate for such modelling. In literature, evaluations have been performed by the painstaking solving of analytical modelling. We propose an evaluation procedure for the JNT error due to residual correlations which blends analytical and numerical approaches, with the benefits of both: a rigorous and accurate circuit noise modelling, and a fast and flexible evaluation with an user-friendly commercial tool. The method is applied to a simple but very effective ultralow-noise amplifier employed in a working JNT. △ Less

Submitted 28 December, 2009; originally announced December 2009.

Comments: 7 figures